This document explains the Exec and Virtual Exec processes, and how to troubleshoot high CPU utilization in these processes.
Cisco recommends that you read Troubleshooting High CPU Utilization on Cisco Routers before you proceed with this document.
This document is not restricted to specific software and hardware versions.
The information presented in this document was created from devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If you are working in a live network, ensure that you understand the potential impact of any command before using it.
For more information on document conventions, refer to the Cisco Technical Tips Conventions.
The Exec process in Cisco IOS® software is responsible for communication on the tty lines (console, auxiliary, asynchronous) of the router. The Virtual Exec process is responsible for the vty lines (telnet sessions).
The Exec and Virtual Exec processes are Medium-priority processes, so if there are other processes that have a higher priority (High or Critical), the higher priority processes get the CPU resources.
router#show process | i CPU|Exec CPU utilization for five seconds: 0%/0%; one minute: 0%; five minutes: 0% PID QTy PC Runtime (ms) Invoked uSecs Stacks TTY Process 22 M* 0 9644 1733 5564 9732/12000 0 Exec 46 ME 80468980 28 6 466610520/12000 66 Virtual Exec
Refer to The show processes Command for a full explanation of the output from this command.
If there is a lot of data transferred through these sessions, the CPU utilization for the Exec process increases.
This is because when the router wants to send a simple character through these lines, the router uses some CPU resources:
For the console (Exec), the router uses one interrupt per character.
The console interrupt can be seen in the show stacks command output:
router#show stacks Minimum process stacks: Free/Size Name 11516/12000 Router Init 9404/12000 Init 5520/6000 AIM_MIB_CREATION 5448/6000 RADIUS INITCONFIG 9728/12000 Virtual Exec Interrupt level stacks: Level Called Unused/Size Name 1 23035463 7008/9000 Network interfaces 2 0 9000/9000 Timebase Reference Interrupt 3 0 9000/9000 PA Management Int Handler 6 9791 8892/9000 16552 Con/Aux Interrupt 7 1334963882 8920/9000 MPC860 TIMER INTERRUPT
For the vty line (Virtual Exec), the telnet session has to build a TCP packet and send the character(s) to the telnet client.
Listed here are some possible reasons for high CPU utilization in the Exec process:
Too much data is sent through the console port.
Too many console messages generated by the router is a possible cause.
There is a bug in the Cisco IOS software.
The exec command is configured for asynchronous and auxiliary lines.
If a line has only outgoing traffic, the Exec process should be disabled for this line, because if the device (for example, a modem) attached to this line sends some unsolicited data, the Exec process starts on this line.
If the router is used as terminal-server (for reverse telnet to other device consoles), it is recommended that you configure no exec on the lines that are connected to the console of the other devices. Data that comes back from the console might otherwise start an EXEC process, which uses CPU resources.
Listed here are some possible reasons for high CPU utilization in the Virtual Exec process:
A software bug in the Cisco IOS software
Too much data is sent across the telnet sessions.
The most common reason for high CPU utilization in the Virtual Exec process is that too much data is transferred from the router to the telnet session.
This can happen when commands with long outputs (such as show tech-support, show memory, and so on) are executed from the telnet session.
The amount of data transferred through each vty session can be verified with the show tcp command:
router#show tcp vty 0 tty66, virtual tty from host 10.48.77.64 Connection state is ESTAB, I/O status: 1, unread input bytes: 1 Local host: 10.48.77.27, Local port: 23 Foreign host: 10.48.77.64, Foreign port: 11006 ........ Datagrams (max data segment is 1460 bytes): Rcvd: 525 (out of order: 0), with data: 53, total data bytes: 87 Sent: 366 (retransmit: 257, fastretransmit: 0), with data: 356, total data bytes: 158187
A hung telnet session leads to a high CPU due to the Virtual Exec process. In order to clear the hung telnet session, the device needs to be reloaded in most cases. The other way to clear the hung telnet session is to clear the TCP process. The TCP process can be identified with the command show tcp brief as in this output:
Router#show tcp brief TCB Local Address Foreign Address (state) 02FA62D0 172.16.152.75.23 dhcp-171-69-104-.3013 ESTAB
From the above output, the TCP process 02FA62D0 needs to be cleared in order to clear the hung telnet session with the command clear tcp tcb 0x02fa62d0 .
The Cisco Support Community is a forum for you to ask and answer questions, share suggestions, and collaborate with your peers.
Refer to Cisco Technical Tips Conventions for information on conventions used in this document.