This document explains how to download a software image to a Cisco 2600/2800/3800 Series Router using Trivial File Transfer Protocol (TFTP) over the first LAN port using the ROMmon tftpdnld command.
You can only download files to the router. You cannot use ROMmon TFTP to get files from the router.
The transfer does not support route bridging on Token Ring ports.
There are no specific requirements for this document.
This document is not restricted to specific software and hardware versions.
Refer to Cisco Technical Tips Conventions for more information on document conventions.
First, you must set ROMmon environment variables prior to the TFTP download. All variable names are case sensitive.
You can view the ROMmon environment variables by using the set command, as shown here:
rommon 3 > set PS1=rommon ! > IP_ADDRESS=172.18.16.76 IP_SUBNET_MASK=255.255.255.192 DEFAULT_GATEWAY=172.18.16.65 TFTP_SERVER=172.18.16.2 TFTP_FILE=quake/rel22_Jan_16/c2600-i-mz
The variables to set for tftpdnld are shown here:
usage: tftpdnld [-ur] Use this command for disaster recovery only to recover an image via TFTP. Monitor variables are used to set up parameters for the transfer. (Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.) "ctrl-c" or "break" stops the transfer before flash erase begins. The following variables are REQUIRED to be set for tftpdnld: IP_ADDRESS: The IP address for this unit IP_SUBNET_MASK: The subnet mask for this unit DEFAULT_GATEWAY: The default gateway for this unit TFTP_SERVER: The IP address of the server to fetch from TFTP_FILE: The filename to fetch The following variables are OPTIONAL: TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=7) TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200) TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1) Command line options: -r: do not write flash, load to DRAM only and launch image -u: upgrade the rommon, system will reboot once upgrade is complete rommon 14 >
Note: As detailed in Cisco bug ID CSCdk81077 (registered customers only) , for Cisco 2600 and 1720 Series Routers running the ROM monitor command tftpdnld, the command might report a bad checksum comparison when it loads Cisco IOS software images of Cisco IOS Software Release 12.0(2.2)T or later.
Note: As a workaround to this problem, set the ROM monitor variable TFTP_CHECKSUM to 0. This is done by defining the variable TFTP_CHECKSUM=0 from the ROM monitor set command, and then proceeding with the tftpdnld procedure.
The variables to set for Token Ring are shown here:
|On the Cisco 2612, this variable sets the Token Ring or Ethernet port. 0 = use Ethernet port 1 = use Token Ring port Default is 0||For a Token Ring port, this variable sets the ring speed and duplex mode. 0 = 4 Mbps half-duplex mode 1 = 4 Mbps full-duplex mode 2 = 16 Mbps half-duplex mode 3 = 16 Mbps full-duplex mode Default is 2|
The variables to set for Fast Ethernet are shown here:
|0 = 10 Mbps half-duplex mode 1 = 10 Mbps full-duplex mode 2 = 100 Mbps half-duplex mode 3 = 100 Mbps full-duplex mode 4 = auto-negotiation Default is 4|
You must use the sync command to save ROMmon environment variables to nonvolatile RAM (NVRAM).
rommon 16 > IP_ADDRESS=184.108.40.206 rommon 17 > IP_SUBNET_MASK=255.255.254.0 rommon 18 > DEFAULT_GATEWAY=220.127.116.11 rommon 19 > TFTP_SERVER=18.104.22.168 rommon 20 > TFTP_FILE=c2600-is-mz.113-2.0.3.Q rommon 21 > tftpdnld IP_ADDRESS: 22.214.171.124 IP_SUBNET_MASK: 255.255.254.0 DEFAULT_GATEWAY: 126.96.36.199 TFTP_SERVER: 188.8.131.52 TFTP_FILE: c2600-is-mz.113-2.0.3.Q Invoke this command for disaster recovery only. WARNING: all existing data in all partitions on flash will be lost! Do you wish to continue? y/n: [n]: y Receiving c2600-is-mz.113-2.0.3.Q from 184.108.40.206 !!!!!.!!!!!!!!!!!!!!!!!!!.!! File reception completed. Copying file c2600-is-mz.113-2.0.3.Q to flash. Erasing flash at 0x607c0000 program flash location 0x60440000 rommon 22 >
The Cisco Support Community is a forum for you to ask and answer questions, share suggestions, and collaborate with your peers.
Refer to Cisco Technical Tips Conventions for information on conventions used in this document.