Guest

Cisco Line Cards

Cisco 10000 Series 8-Port E3/DS3 ATM Line Card

Data Sheet


Cisco 10000 Series 8-Port E3/DS3 ATM Line Card


The Cisco 10000 Series 8-Port E3/DS3 ATM Line Card provides high-density connectivity and deployment flexibility for the Cisco 10000 Series. Combined with comprehensive features for broadband aggregation, the high-performance, carrier-class Cisco 10000 Series delivers unmatched deployment flexibility, reliability, and high-density connectivity for service provider broadband aggregation (Figure 1).

Figure 1
Cisco 10000 Series 8-Port E3/DS3 ATM Line Card

Product Description

The Cisco 10000 Series 8-Port E3/DS3 ATM Line Card features high-performance programmable segmentation and reassembly (SAR), adapted for various applications, including advanced traffic management, cell scheduling, and integrated buffer management. The programmable nature of SAR allows flexibility for software upgrades and support for new standards. By mapping IP class of service (CoS) to ATM quality of service (QoS) on the Cisco 10000 Series ATM line cards, the flow of mission-critical data can be effectively managed across heterogeneous IP and ATM networks.

Key Features and Benefits

  • Per-virtual circuit and per-virtual path traffic shaping—The Cisco 10000 Series 8-Port E3/DS3 ATM Line Card supports both per-virtual circuit and per-virtual path traffic shaping, providing flexibility and control over every virtual circuit and virtual path configured. Per-virtual circuit and per-virtual path traffic shaping allows bursts of traffic to conform to a predetermined contract, ensuring that excessive traffic from one virtual circuit does not incur data loss on other virtual circuits. This function is very important when connecting to an ATM WAN or public ATM network, where ATM switches may discard excessive traffic at the point of ingress.
  • Hardware-based traffic shaping—The Cisco 10000 Series 8-Port E3/DS3 ATM Line Card supports IP layer traffic shaping on the high-performance Parallel Express Forwarding (PXF) network processors of the Cisco 10000 Series Performance Routing Engine (PRE). The ATM layer traffic shaping is supported on the module. Supporting traffic shaping in hardware means that there is no performance degradation when traffic shaping is enabled, allowing line-rate performance with traffic shaping.
  • Standards-based ATM implementation for interoperability—The 8-port E3/DS3 ATM line card is a standards-based ATM interface that allows customers to integrate the Cisco 10000 Series into existing ATM networks. By implementing a standards-based version of ATM, Cisco ensures that customers will be able to easily and quickly integrate the Cisco 10000 Series into their current ATM network. Further, by using standard operations, administration, and management (OA&M) F4 and F5, customers will benefit from lower management and administrative expenses and improved overall manageability. Network managers can take advantage of Cisco 10000 Series traffic management and QoS features on the E3/DS3 ATM module.

ATM Features

  • Supports ATM Forum traffic management service categories: non-real-time variable bit rate (nrt-VBR) and universal bit rate (UBR)
  • Supports User-Network Interface (UNI) Versions 3.0 and 3.1
  • Supports Integrated Local Management Interface (ILMI) permanent-virtual-circuit (PVC) autodiscovery feature
  • Supports up to 4000 virtual circuits per port; up to 32,000 virtual circuits per module on the broadband aggregation Cisco IOS® trains, beginning with release 12.2(16)BX
  • Offers full support for virtual-path-identifier (VPI) and virtual-circuit-identifier (VCI) address width (16-bit VCI, 8-bit VPI)
  • Supports PVCs and permanent virtual path (PVPs)
  • Supports per-virtual circuit queuing and shaping for nrt-VBR
  • Supports Class-Based Weighted Fair Queuing (CBWFQ) and Priority Queuing for nrt-VBR virtual circuits
  • Offers RFC 1483 support for routed protocols
  • Offers RFC 2684 support for ATM adaptation layer 5 (AAL5) Logical Link Control (LLC) and subnetwork attachment point Subnetwork Access Protocol (SNAP) encapsulations and AAL5 multiplexing IPv4 encapsulation
  • Supports PVCs over AAL5
  • Supports call admission control (does not allow configuration of nrt-VBR PVCs if requested bandwidth is not available on the port)
  • Supports OA&M F4 and F5 segment and end-to-end loopback
  • Supports OA&M management (allows management of PVCs using this feature via OA&M)
  • Supports SONET/SDH OC-3 STS-3c/STM-1c framing format

Packet Layer Features

  • Supports all IP routing protocols
  • Supports application of QoS (Priority Queuing and CBWFQ, Weighted Random Early Detection [WRED], committed access rate [CAR]) to each nrt-VBR PVC, and to all UBR PVCs as a group using Cisco modular command-line interface (CLI)
    • Supports ATM cell loss priority (CLP) bit
  • Supports multicast
  • Supports access control lists (ACLs)
  • Supports Multiprotocol Label Switching (MPLS)
    • Frame-mode MPLS over ATM
    • MPLS cell mode with Label-Controlled ATM Interface (LC-ATM) interface support; this value-added feature allows service providers with existing ATM backbone to upgrade their switches with label switch controllers to support the MPLS control plane; it is a great value proposition, enabling new services to be provisioned over the infrastructure while protecting the investment
  • Supports turbo QoS classification, 802.1Q virtual LAN (VLAN), policy-based routing, and per-packet load balancing

High-Availability Features

  • Supports online insertion and removal (OIR)
  • Supports Cisco IOS Software Route Processor Redundancy Plus (RPR+)

Specifications

Physical

  • Full height; occupies a single slot in the Cisco 10000 Series chassis
  • Hot-swappable, no slot dependency
  • Weight: 4.75 lb (2.16 kg)
  • Dimensions (H x W x D): 16.0 x 1.12 x 9.97 in. (40.64 x 2.83 x 25.32 cm)
  • Network Equipment Building Standards (NEBS) Level 3 compliant

Environmental

  • Storage temperature: -38 to 150° F (-40 to 70° C)
  • Operating temperature, nominal: 41 to 104° F (5 to 40° C)
  • Operating temperature, short term: 23 to 131° F (-5 to 55° C)
  • Storage relative humidity: 5 to 95% relative humidity
  • Operating humidity, nominal: 5 to 85% relative humidity
  • Operating humidity, short term: 5 to 90% relative humidity
  • Operating altitude: -60 to 4000m

Regulatory Compliance Safety

  • UL60950/CAN/CSA-C22.2 No. 60950-00, third edition, dated December 1, 2000, with no deviation considered to be less stringent than IEC 60950
  • EN60950 with Amendments 1-4, for CE Marking to the LVD directive
  • IEC 60950 third edition with Amendments 1-4, including all national and group deviations
  • AS/NZS 60950:2000
  • AS/NZS 3260-1993 with Amendments 1-4
  • ACA TS001-1997

Electromagnetic Emissions Certification

  • AS/NZ 3548:1995 (including AMD I + II) Class B
  • EN55022:1998 Class B
  • CISPR 22:1997
  • EN55022:1994 (including Amendments I+ II)
  • 47 CFR Part 15:2000 (FCC) Class B
  • VCCI V-3/01.4 Class 2
  • CNS-13438:1997 Class B
  • GR1089:1997 (including Rev. 1: 1999)

Immunity

  • EN300386:2000TNE EMC requirements; product family standard; high priority of service; central office and noncentral office locations
  • EN50082-1:1992/1997
  • EN50082-2:1995 Generic Immunity Standard, Heavy Industrial CISPR24:1997
  • EN55024: 1998 Generic ITE immunity standard
  • EN61000-4-2:1995+AMD I + IIESD, Level 4/8 kV contact,15 kV air
  • IEC-1000-4-3:1995+AMD 1 Radiated Immunity, 10 V/m
  • IEC-1000-4-4:1995 Electrical Fast Transients, Level 4/4 kV/B
  • IEC-1000-4-5:1995+AMD 1 DC surge-Class 3; AC surge-Class 4
  • EN61000-4-6:1996+AMD 1 RF conducted immunity, 10 Vrms
  • EN61000-4-11:1995 Voltage Dips and Sags
  • ETS300 132-2:1996+corregendum, Dec. 1996
  • GR1089:1997 (including Rev. 1: 1999)

Network Equipment Building Standards

The line card meets the following NEBS:

  • Level 3 compliant
  • Telcordia SR-3580 Criteria Levels, issued 11/95
  • GR-1089-CORE: Electromagnetic Compatibility & Electrical Safety, issued 10/02
  • GR-63-CORE: Physical Protection Requirements, issued 4/02
  • SBC Equipment Requirements: TP76200 MP and TP76400 MP
  • Verizon Equipment Requirements: SIT.NEBS.TE.NPI.2002.010

European Telecommunication Standards Institute

  • ETSI 300 386-1—Levels for equipment with a "high priority of service" that is installed in "locations other than telecommunication centers"
  • ETSI 300 386-2: 1997—Levels for equipment with a "high priority of service" that is installed in "locations other than telecommunication centers"
  • ETSI 300 132-2: December 1994—Power-supply interfaces at the input to telecommunications equipment Sections 4.8 and 4.9

ATM Standards

  • ATM Forum Traffic Management Specification Version 4.0
  • UNI Versions 3.1 and 3.0
  • UNI 4.0 Traffic Management Specification
  • ILMI Specification Version 4.0

Network Management

  • Simple Network Management Protocol (SNMP)
  • Cisco Discovery Protocol
  • SNMP Management Information Base (MIB)-II (RFC 1213)
  • ILMI MIB

Power Budget

  • Component: 8-port E3/DS3 ATM line card
  • Unit power: 30W

LEDs

  • CARRIER STATUS (green, one per port)
  • LOOPBACK (yellow, one per port)
  • ALARM (yellow, one per port)
  • FAIL (yellow, one per card)

Product System Requirements and Compatibility

Hardware Requirements

  • Chassis: The Cisco 10000 Series 8-Port E3/DS3 ATM Line Card is supported in the Cisco 10008 chassis.
  • PREs: The Cisco 10000 Series 8-Port E3/DS3 ATM Line Card is supported on the PRE-2s available on the Cisco 10000 Series in the software trains in which PRE-2s are available.

Software Requirements

The line card is supported in Cisco IOS Software Release 12.2(16)BX and later releases. For information about releases that support the PRE-2, refer to:

http://www.cisco.com/pcgi-bin/front.x/Support/HWSWmatrix/hwswmatrix.cgi

Product Ordering Details

Visit:

http://www.cisco.com/public/ordering_info.shtml

to place an order.

Ordering Information

Table 1 gives part numbers for the Cisco 10000 Series 8-Port E3/DS3 ATM Line Card.

Table 1   Part Numbers for Cisco 10000 Series 8-Port E3/DS3 ATM Line Card

Part Number Description
ESR-8E3DS3-ATM

8-port E3/DS3 ATM line card for the Cisco 10000 Series

ESR-8E3DS3-ATM=

8-port E3/DS3 ATM line card for the Cisco 10000 Series, spare

Product Ordering Details: Migration Program

A Cisco Technology Migration Plan (TMP) has been established for this product. The TMP is a sales program that allows customers to trade in Cisco products to receive a trade-in credit toward the purchase of any new Cisco product. The program underscores Cisco's commitment to the customer in terms of end-to-end product solutions as well as emphasizing the company's commitment to provide effective migration options for ever-changing network requirements. More specifics about this program are available at:

http://www.cisco.com/go/tradein .

Service and Support

Cisco Systems® offers a wide range of service and support options for its customers. More information about Cisco service and support programs and benefits are available at:

http://www.cisco.com/en/US/support/index.html