The Cisco® ATA 187 Analog Telephone Adaptor is a handset-to-Ethernet adaptor that turns traditional telephone devices into IP devices. Customers can take advantage of the many new and exciting IP telephony applications by connecting their analog devices to Cisco ATAs.
The Cisco ATA products are standards-based communication devices that deliver true, next-generation voice-over-IP (VoIP) terminations to businesses and residences worldwide.
• Protects existing telephone investment: The Cisco ATA 187 supports two voice ports, each with its own independent telephone number, and a single RJ-45 10/100 BASE-T Ethernet port. This adaptor can make use of existing Ethernet LANs in addition to broadband pipes such as DSL, fixed wireless, and cable modem deployments.
• Cost effective: The Cisco ATA 187 helps customers turn their analog phone devices into IP devices cost effectively and is the preferred solution to address the needs of customers who connect to enterprise networks, small-office environments, or the emerging VoIP managed voice services and local services market.
Enterprise customers are using the Cisco ATA 187 to connect analog phones and fax machines to their VoIP network. Service providers are taking advantage of emerging telephony applications and the ease of deploying second-line services using the Cisco ATA 187 (Figures 1 and 2).
Figure 1. Cisco ATA 187: Endpoint for an End-to-End Broadband System
Figure 2. Cisco ATA 187 as Endpoint in Session Initiation Protocol (SIP) Network
* DSL and cable mode need SIP support.
Features and Benefits
Table 1 lists the features and benefits of the Cisco ATA 187.
Table 1. Features and Benefits
Configuration and Provisioning
• Configuration as per Cisco endpoints devices
• Autoprovisioning with Trivial File Transfer Protocol (TFTP) for servers
• Automatic assignment of IP address, network routing IP, and subnet mask using Dynamic Host Configuration Protocol (DHCP)
• Touch-tone telephone keypad configuration with voice prompt
• Administration password to protect configuration and access
• Remote upgrades through network
• Cisco Unified Communications Manager (UCM) standard configuration and provisioning options
• Ease of administration
• Advanced preprocessing to optimize full-duplex voice compression
• High-performance line-echo cancellation to eliminate noise and echo
• Voice activity detection (VAD) and comfort noise generation (CNG) to save bandwidth by delivering voice, not silence
• Dynamic network monitoring to reduce jitter artifacts such a packet loss
Clear, natural-sounding voice quality
• Session Initiation Protocol (SIP) on the Cisco line side
Allows interoperation with Cisco UCM SIP solution
• Secure Real-Time Transfer Protocol and Transport Layer Security (SRTP/TLS) over SIP
Secure media and secure signaling support, for secure solutions
• T38 fax support
Standard fax capability to send faxes over the IP network
• Fits in most environments
New form-factor design based on the Cisco endpoints portfolio
Cisco UCM Version Compatibility
• Cisco UCM Versions 7.1.5, 8.0.2, or higher
Table 2 presents the specifications for the Cisco ATA 187.
Table 2. Product Specifications
Power supply: Universal AC power supply 100 and 240V
Power adaptor output voltage: +12.0 VDC at 1A maximum
Less than 34 dBA at 3 feet
2 RJ 11
Operating temperature: 23 to 113°F (5 to 45 °C)
Non-operating temperature: -13 to 158ºF (-25 to 70ºC)
Operating humidity: 5 to 95% noncondensing
Mean time between failure (MTBF)
(H x W x D) and weight
Dimensions: 1.5 x 5.4 x 6.7 in. (3.8 x 13.7 x 17.0 cm)
Weight: 9.2 oz (260g)
RoHS- and WEEE-compliant materials
To turn device on and off
Cisco ATA SIP services
• IP address assignment: Provided by DHCP or statically configured
• Cisco ATA configuration through Cisco UCM configuration interface
• Comfort noise during silence period when using G.711
• Advanced audio mode
• Caller ID format
• Ring cadence format
• Silence suppression
• Hook-flash detection timing configuration
• Configurable on-hook delay
• Type of service (ToS) configuration for audio and signaling Ethernet packets
• Debugging and diagnostic tools
Cisco ATA supports the methods listed here (for more information, refer to RFC-3261):
• Caller ID
• Call-waiting caller ID
• Voice-mail indication
• Conference call
• Call waiting
• Call forwarding
• Calling-line identification
• Unattended transfer
• Attended transfer
• Shared line
• Speed dial
• Meet me
• Pick up
Other supported protocols
• IEEE 802.1Q VLAN tagging
• Cisco Discovery Protocol
• Internet Control Message Protocol (ICMP)
• Real-Time Transport Protocol (RTP)
• Trivial File Transfer Protocol (TFTP)
• User Datagram Protocol (UDP)
The Cisco ATA supports two modes of fax services, in which fax signals are transmitted using the G.711 codec:
• Fax pass-through mode: The mode enables receiver-side called-station-identification (CED) tone detection with automatic G.711A-law or G.711μ-law switching.
• T38 fax relay mode: The T.38 fax relay feature enables devices to use fax machines to send files over the IP network. In general, when a fax is received, it is converted to an image, sent to the T.38 fax device, and converted back to an analog fax signal. T.38 fax relays configured with voice gateways decode or demodulate the fax signals before they are transported over IP.
Note: Success of fax transmission depends on network conditions and the fax modem response to these conditions. The network must have reasonably low network jitter, network delay, and packet loss rate.
Voice codecs supported
• SRTP secures voice conversations on the network and provides protection against replay attacks.
• TLS is a cryptographic protocol that secures data communications such as email on the Internet. TLS is functionally equivalent to SSL.
• LAN port: One RJ-45 10/100BASE-T Fast Ethernet port
• Quality of service (QoS): Precedence setting and differentiated services code point (DSCP)
Call progress tones
Configurable based on network locale
• Echo canceller for each port
• 8-millisecond (ms) echo length
• Nonlinear echo suppression (echo return loss [ERL] greater than 28 dB for f = 300 to 3400 Hz)
Help customers understand all the components or parts they need to purchase to install and use the product. This section also provides a direct link to the Cisco Ordering Tool, and Table 3 lists part numbers for customer convenience.
Cisco Services integrates closely with consumer marketing teams as an essential element of any technology solution. Please contact your Cisco Services marketing communications manager if you have not already received targeted services content blocks for integration. Please email firstname.lastname@example.org if you are not sure of the appropriate contact.
Cisco Services make networks, applications, and the people who use them work better together.
Today, the network is a strategic platform in a world that demands better integration between people, information, and ideas. The network works better when services, together with products, create solutions aligned with business needs and opportunities.
The unique Cisco Lifecycle approach to services defines the requisite activities at each phase of the network lifecycle to help ensure service excellence. With a collaborative delivery methodology that joins the forces of Cisco, our skilled network of partners, and our customers, we achieve the best results.
For More Information
Use this section to a "call to action" message. Insert your product-specific content in the standard wording below. If there is no alias, delete the "or" and the alias blank, and add a period after "representative." Local account representative" should be linked to an appropriate general rep page, if available. Consider directing data sheet readers to white papers, solution overviews, case studies, or other marketing materials.
For more information about the Cisco Enter Product Name, visit Enter URL for Product Home Page or contact your local account representative or Enter Cisco alias.