Cisco Wireless LAN Controller Command Reference, Release 4.1 - Controller Commands [Cisco 4400 Series Wireless LAN Controllers]

Table Of Contents

Cisco Wireless LAN Controller
Command Reference

Using the ? command

Using the Help Command

Viewing Configurations

show 802.11a

show 802.11a l2roam

show 802.11b

show 802.11b l2roam

show 802.11h

show aaa auth

show acl

show acl cpu

SHOW ADVANCED 802.11A COMMANDS

show advanced 802.11a channel

show advanced 802.11a group

show advanced 802.11a logging

show advanced 802.11a monitor

show advanced 802.11a profile

show advanced 802.11a receiver

show advanced 802.11a summary

show advanced 802.11a txpower

SHOW ADVANCED 802.11B COMMANDS

show advanced 802.11b channel

show advanced 802.11b group

show advanced 802.11b logging

show advanced 802.11b monitor

show advanced 802.11b profile

show advanced 802.11b receiver

show advanced 802.11b summary

show advanced 802.11b txpower

show advanced client-handoff

show advanced eap

show advanced location

show advanced max-1x-sessions

show advanced probe-limit

show advanced rate

show advanced send-disassoc-on-handoff

show advanced statistics

show advanced timers

SHOW AP COMMANDS

show ap auto-rf

show ap bmode

show ap bhrate

show ap ccx rm

show ap cdp neighbors detail

show ap config

show ap core-dump

show ap crash-file

show ap inventory

show ap stats

show ap summary

show ap wlan

show arp switch

show auth-list

show boot

SHOW CERTIFICATE COMMANDS

show certificate compatibility

show certificate summary

SHOW CLIENT COMMANDS

show client ap

show client ccx log-response

show client ccx rm

show client ccx stats-report

show client detail

show client location-calibration summary

show client report

show client summary

show client username

show country

show country channels

show country supported

show cpu

show custom-web

show database summary

show debug

show dhcp

show dhcp proxy

show eventlog

show exclusionlist

show ike

show interface

show inventory

show ipsec

show known ap

show l2tp

show lag summary

show ldap summary

show load-balancing

show local-auth certificates

show local-auth config

show local-auth statistics - TBD Need Info

show local-auth registrations

show local-auth statistics

show location summary

show loginsession

show macfilter

SHOW MESH COMMANDS

show mesh cac bwused

show mesh cac calls

show mesh client-access

show mesh env summary

show mesh linkrate

show mesh neigh

show mesh neigh summary

show mesh path

show mesh range

show mesh secondary-backhaul

show mesh stats

show mesh summary

show mgmtuser

SHOW MOBILITY COMMANDS

show mobility anchor

show mobility statistics

show mobility summary

show msglog

show nac statistics

show nac summary

show netuser

show network

show pmk-cache

show port

show qos queue_length all

SHOW RADIUS COMMANDS

show radius acct statistics

show radius auth statistics

show radius rfc3576 statistics

show radius summary

SHOW RFID COMMANDS

show rfid config

show rfid detail

show rfid summary

SHOW ROGUE ADHOC COMMANDS

show rogue adhoc detailed

show rogue adhoc summary

SHOW ROGUE AP COMMANDS

show rogue ap clients

show rogue ap detailed

show rogue ap summary

SHOW ROGUE CLIENT COMMANDS

show rogue client detailed

show rogue client summary

show route summary

show rules

show run-config

show serial

show sessions

show snmpcommunity

show snmptrap

show snmpv3user

show snmpversion

show spanningtree port

show spanningtree switch

SHOW STATS COMMANDS

show stats port

show stats switch

show switchconfig

show sysinfo

show syslog

show tacacs acct statistics

show tacacs athr statistics

show tacacs auth statistics

show tacacs summary - TBD Need Info

show tech-support

show time

show trapflags

show traplog

show version

show watchlist

show wlan

show wps

show wps cids-sensor detail

show wps cids-sensor summary

show wps client-exclusion

show wps signature events standard

show wps signature events summary

show wps signature summary

show wps summary

Setting Configurations

CONFIG 802.11A COMMANDS

config 802.11a antenna extAntGain

config 802.11a antenna diversity

config 802.11a antenna mode

config 802.11a antenna selection

config 802.11a beaconperiod

802.11a CAC Video and Voice Commands

config 802.11a cac video acm

config 802.11a cac video max-bandwidth

config 802.11a cac video roam-bandwidth

config 802.11a cac video tspec-inactivity-timeout

config 802.11a cac voice acm

config 802.11a cac voice max-bandwidth

config 802.11a cac voice roam-bandwidth

config 802.11a cac voice tspec-inactivity-timeout

config 802.11a cac voice load-based

config 802.11a cac voice stream-size

End of CAC 802.11a Commands

config 802.11a channel

config 802.11a disable

config 802.11a dtim

config 802.11a dtpc

config 802.11a enable

config 802.11a exp-bwreq

config 802.11a fragmentation

config 802.11a l2roam

config 802.11a pico-cell

config 802.11a rate

config 802.11a txPower

CONFIG 802.11B COMMANDS

config 802.11b 11gSupport

config 802.11b antenna diversity

config 802.11b antenna extAntGain

config 802.11b antenna selection

config 802.11b beaconperiod

802.11b CAC Video and Voice Commands

config 802.11b cac video acm

config 802.11b cac video max-bandwidth

config 802.11b cac video roam-bandwidth

config 802.11b cac video tspec-inactivity-timeout

config 802.11b cac voice acm

config 802.11b cac voice max-bandwidth

config 802.11b cac voice roam-bandwidth

config 802.11b cac voice tspec-inactivity-timeout

config 802.11b cac voice load-based

config 802.11b cac voice stream-size

End of CAC 802.11b Commands

config 802.11b channel

config 802.11b disable

config 802.11b dtim

config 802.11b dtpc

config 802.11b enable

config 802.11b exp-bwreq

config 802.11b fragmentation

config 802.11b l2roam

config 802.11b pico-cell

config 802.11b preamble

config 802.11b rate

config 802.11b txPower

CONFIG 802.11h COMMANDS

config 802.11h channelswitch

config 802.11h powerconstraint

config 802.11h setchannel

config aaa auth

config acl apply

config acl create

config acl cpu

config acl delete

config acl rule

CONFIG ADVANCED 802.11A COMMANDS

config advanced 802.11a channel foreign

config advanced 802.11a channel load

config advanced 802.11a channel noise

config advanced 802.11a channel update

config advanced 802.11a factory

config advanced 802.11a group-mode

config advanced 802.11a logging channel

config advanced 802.11a logging coverage

config advanced 802.11a logging foreign

config advanced 802.11a logging load

config advanced 802.11a logging noise

config advanced 802.11a logging performance

config advanced 802.11a logging txpower

config advanced 802.11a monitor channel-list

config advanced 802.11a monitor coverage

config advanced 802.11a monitor load

config advanced 802.11a monitor mode

config advanced 802.11a monitor noise

config advanced 802.11a monitor signal

config advanced 802.11a profile clients

config advanced 802.11a profile coverage

config advanced 802.11a profile customize

config advanced 802.11a profile exception

config advanced 802.11a profile foreign

config advanced 802.11a profile level

config advanced 802.11a profile noise

config advanced 802.11a profile throughput

config advanced 802.11a profile utilization

config advanced 802.11a receiver

config advanced 802.11a txpower-update

CONFIG ADVANCED 802.11B COMMANDS

config advanced 802.11b 7920VSIEConfig

config advanced 802.11b channel foreign

config advanced 802.11b channel load

config advanced 802.11b channel noise

config advanced 802.11b channel update

config advanced 802.11b factory

config advanced 802.11b group-mode

config advanced 802.11b logging channel

config advanced 802.11b logging coverage

config advanced 802.11b logging foreign

config advanced 802.11b logging load

config advanced 802.11b logging noise

config advanced 802.11b logging performance

config advanced 802.11b logging txpower

config advanced 802.11b monitor channel-list

config advanced 802.11b monitor coverage

config advanced 802.11b monitor load

config advanced 802.11b monitor mode

config advanced 802.11b monitor noise

config advanced 802.11b monitor signal

config advanced 802.11b profile clients

config advanced 802.11b profile coverage

config advanced 802.11b profile customize

config advanced 802.11b profile exception

config advanced 802.11b profile foreign

config advanced 802.11b profile level

config advanced 802.11b profile noise

config advanced 802.11b profile throughput

config advanced 802.11b profile utilization

config advanced 802.11b receiver

config advanced 802.11b txpower-update

config advanced arp

config advanced client-handoff

config advanced eap

config advanced location

config advanced rate

config advanced statistics

CONFIG ADVANCED TIMERS COMMANDS

config advanced timers ap-discovery-timeout

config advanced timers ap-heartbeat-timeout

config advanced timers auth-timeout

config advanced timers eap-timeout

config advanced timers eap-identity-request-delay

CONFIG AP COMMANDS

config ap add

config ap bhmode

config ap bhrate

config ap bridgegroupname

config ap bridging

config ap cdp

config ap core-dump

config ap crash-file clear-all

config ap crash-file delete

config ap crash-file get-crash-file

config ap crash-file get-radio-core-dump

config ap delete

config ap disable

config ap enable

config ap group-name

config ap led-state

config ap location

config ap mode

config ap name

config ap port

config ap power injector

config ap power pre-standard

config ap primary-base

config ap remote-debug

config ap reporting-period

config ap reset

config ap role

config ap rst-button

config ap secondary-base

config ap sniff 802.11a

config ap sniff 802.11b

config ap static-ip

config ap stats-timer

config ap tertiary-base

config ap tftp-downgrade

config ap wlan

config ap username

config auth-list add

config auth-list ap-policy

config auth-list delete

config boot

config cdp timer

config certificate

config client ccx log-request

config client ccx stats-request

config client deauthenticate

config client location-calibration

config country

config custom-web ext-webauth-mode

config custom-web ext-webauth-url

config custom-web ext-webserver

config custom-web redirectUrl

config custom-web weblogo

config custom-web webmessage

config custom-web webtitle

config database size

config dhcp

config dhcp proxy

config exclusionlist

CONFIG INTERFACE COMMANDS

config interface acl

config interface address

config interface ap-manager

config interface create

config interface delete

config interface dhcp

config interface hostname

config interface port

config interface vlan

config known ap

config lag

config ldap

config ldap add

config load-balancing

config local-auth eap-profile

config local-auth method fast

config local-auth method tls

config local-auth user-credentials

config location add

config location delete

config location description

config location disable

config location enable

config location interface-mapping

config logging buffered

config loginsession close

CONFIG MACFILTER COMMANDS

config macfilter add

config macfilter delete

config macfilter description

config macfilter interface

config macfilter ip-address

config macfilter mac-delimiter

config macfilter radius-compat

config macfilter wlan-id

config mesh client-access

config mesh linktest

config mesh linkdata

config mesh mac-filter

config mesh range

config mesh secondary-backhaul

config mesh security

CONFIG MGMTUSER COMMANDS

config mgmtuser add

config mgmtuser delete

config mgmtuser description

config mgmtuser password

CONFIG MOBILITY COMMANDS

config mobility group anchor

config mobility group domain

config mobility group member

config mobility secure-mode

config mobility statistics reset

CONFIG MSGLOG LEVEL COMMANDS

config msglog level critical

config msglog level error

config msglog level security

config msglog level verbose

config msglog level warning

config nac acl

config nac add

config nac delete

config nac disable

config nac enable

CONFIG NETUSER COMMANDS

config netuser add

config netuser delete

config netuser description

config netuser maxEapUserLogin

config netuser maxuserLogin

config netuser password

config netuser wlan-id

CONFIG NETWORK COMMANDS

config network 802.3-bridging

config network allow-old-bridge-aps

config network ap-fallback

config network apple-talk

config network arptimeout

config network arpunicast

config network bridging-shared-secret

config network fast-ssid-change

config network master-base

config network mgmt-via-wireless

config network multicast

config network otap-mode

config network peer-blocking

config network rf-network-name

config network secureweb

config network ssh

config network telnet

config network usertimeout

config network web-auth-port

config network webmode

config network zero-config

config pmk-cache delete

CONFIG PORT COMMANDS

config port adminmode

config port autoneg

config port linktrap

config port multicast appliance

config port physicalmode

config port power

config prompt

config qos queue_length

CONFIG RADIUS ACCT COMMANDS

config radius acct add

config radius acct delete

config radius acct disable

config radius acct enable

config radius acct network

config radius acct ipsec authentication

config radius acct ipsec disable

config radius acct ipsec enable

config radius acct ipsec encryption

config radius acct ipsec ike

config radius acct retransmit-timeout

CONFIG RADIUS AUTH COMMANDS

config radius auth add

config radius auth delete

config radius auth disable

config radius auth enable

config radius auth ipsec authentication

config radius auth ipsec disable

config radius auth ipsec enable

config radius auth ipsec encryption

config radius auth ipsec ike

config radius auth management

config radius auth network

config radius auth retransmit-timeout

config radius auth rfc3576

config radius aggressive-failover disabled

config radius backward compatibility

config radius callStationIdType

config rfid auto-timeout

config rfid status

config rfid timeout

config rogue adhoc

config rogue ap

config rogue client

config route add

config route delete

CONFIG SERIAL COMMANDS

config serial baudrate

config serial timeout

CONFIG SESSIONS COMMANDS

config sessions maxsessions

config sessions timeout

CONFIG SNMP COMMUNITY COMMANDS

config snmp community accessmode

config snmp community create

config snmp community delete

config snmp community ipaddr

config snmp community mode

config snmp syscontact

config snmp syslocation

CONFIG SNMP TRAPRECEIVER COMMANDS

config snmp trapreceiver create

config snmp trapreceiver delete

config snmp trapreceiver mode

CONFIG SNMP V3USER COMMANDS

config snmp v3user create

config snmp v3user delete

config snmp version

CONFIG SPANNINGTREE PORT COMMANDS

config spanningtree port mode

config spanningtree port pathcost

config spanningtree port priority

CONFIG SPANNINGTREE SWITCH COMMANDS

config spanningtree switch bridgepriority

config spanningtree switch forwarddelay

config spanningtree switch hellotime

config spanningtree switch maxage

config spanningtree switch mode

CONFIG SWITCHCONFIG COMMANDS

config switchconfig flowcontrol

config switchconfig mode

config syslog

config sysname

config tacacs

config tacacs acct

config tacacs athr

config tacacs auth

config tacacs all ....

config time manual

config time ntp

config time timezone

CONFIG TRAPFLAGS COMMANDS

config trapflags 802.11-Security

config trapflags aaa

config trapflags ap

config trapflags authentication

config trapflags client

config trapflags configsave

config trapflags ipsec

config trapflags linkmode

config trapflags multiusers

config trapflags rogueap

config trapflags rrm-params

config trapflags rrm-profile

config trapflags stpmode

config trapflags wps

CONFIG WATCHLIST COMMANDS

config watchlist add

config watchlist delete

config watchlist disable

config watchlist enable

CONFIG WIRELESS LAN COMMANDS

config wlan 7920-support

config wlan 802.11e

config wlan aaa-override

config wlan acl

config wlan broadcast-ssid

config wlan create

config wlan delete

config wlan dhcp_server

config wlan diag-channel

config wlan disable

config wlan enable

config wlan exclusionlist

config wlan interface

config wlan IPv6Support

config wlan mac-filtering

config wlan mfp

config wlan mobility

config wlan qos

config wlan radio

config wlan radius_server

CONFIG WIRELESS LAN SECURITY COMMANDS

config wlan security 802.1X

config wlan security ckip ....

config wlan security cranite

config wlan security fortress

config wlan security ipsec disable

config wlan security ipsec enable

config wlan security ipsec authentication

config wlan security ipsec encryption

config wlan security ipsec config

config wlan security ipsec ike authentication

config wlan security ipsec ike dh-group

config wlan security ipsec ike lifetime

config wlan security ipsec ike phase1

config wlan security ipsec ike contivity

config wlan security passthru

config wlan security static-wep-key authentication

config wlan security static-wep-key disable

config wlan security static-wep-key enable

config wlan security static-wep-key encryption

config wlan security web-auth

config wlan security web-passthrough acl

config wlan security web-passthrough disable

config wlan security web-passthrough email-input

config wlan security web-passthrough enable

config wlan security wpa1 disable

config wlan security wpa1 enable

config wlan security wpa1 pre-shared-key

config wlan security wpa2 disable

config wlan security wpa2 enable

config wlan security wpa2 pre-shared-key

config wlan security wpa2 tkip

config wlan security wpa2 wpa-compat

config wlan timeout

config wlan wmm

CONFIG WPS COMMANDS

config wps ap-authentication

config wps cids-sensor

config wps rogue-ap

config wps signature

lwapp ap controller ip address

Saving Configurations

save config

Clearing Configurations, Logfiles, and Other Actions

clear ap-config

clear arp

clear config

clear lwapp private-config

clear radius acct statistics

clear radius auth statistics

clear stats mobility

clear stats port

clear stats switch

clear stats tacacs

clear redirect-url

clear transfer

clear traplog

clear webimage

clear webmessage

clear webtitle

clear ext-webauth-url

Uploading and Downloading Files and Configurations

transfer download certpassword

transfer download datatype

transfer download filename

transfer download mode

transfer download path

transfer download serverip

transfer download start

transfer download tftpPktTimeout

transfer download tftpMaxRetries

transfer encrypt

transfer upload datatype

transfer upload filename

transfer upload mode

transfer upload pac

transfer upload path

transfer upload serverip

transfer upload start

Troubleshooting

debug aaa

debug aaa local-auth eap

debug ap

debug airewave-director

debug arp

debug bcast

debug cac

debug crypto

debug dhcp

debug disable-all

debug dot11

debug dot1x

debug l2age

debug lwapp

debug lwapp console cli

debug mac

debug mesh security

debug mobility

debug nac

debug ntp

debug pem

debug pm

debug poe

debug rbcp

debug snmp

debug transfer

debug wcp

debug wps

eping

mping

Cisco Wireless LAN Controller
Command Reference

The Cisco Wireless LAN Solution command line interface (CLI) enables operators to connect an ASCII console to the Cisco Wireless LAN Controller and configure the controller and its associated access points.

This document covers the Cisco CLI release 4.1 commands for the following platforms:

•Cisco 2000 series Wireless LAN Controllers

•Cisco 2100 series Wireless LAN Controllers

•Cisco 4400 series Wireless LAN Controllers

•Catalyst 3750G Wireless LAN Controller Switches

•Cisco Wireless Services Module (WiSM) for Cisco Catalyst 6500 Series Switches and Cisco Catalyst 7600 Series Routers

•Cisco Wireless LAN Controller Network Module (WLCM) for Cisco Integrated Services Routers

This chapter contains the following sections:

•Using the Help Command

•Viewing Configurations

•Setting Configurations

•Saving Configurations

•Clearing Configurations, Logfiles, and Other Actions

•Uploading and Downloading Files and Configurations

•Troubleshooting

Using the ? command

To display all of the commands in your current level of the command tree, or to display more information about a particular command, use the ? command.

?
command name ?
When you enter a command information request, put a space between command name and ?.

Examples

The following command shows you all the commands and levels available from the root level.
> ?
clear          Clear selected configuration elements.
config         Configure switch options and settings.
debug          Manages system debug options.
help           Help
linktest       Perform a link test to a specified MAC address.
logout         Exit this session. Any unsaved changes are lost.
ping           Send ICMP echo packets to a specified IP address.
reset          Reset options.
save           Save switch configurations.
show           Display switch options and settings.
transfer       Transfer a file to or from the switch.
The following command shows you that datatype is the only entry at the transfer download level:
> transfer download d?
datatype
The following command shows you the permissible entries for the transfer download datatype command:
> transfer download datatype ?
config         Download Configuration File.
code           Download an executable image to the system.
image          Download a web page logo to the system.
signature      Download a signature file to the system.
webadmincert   Download a certificate for web administration to the system.
webauthcert    Download a web certificate for web portal to the system.
Using the Help Command

To look up keyboard commands, use the help command at the root level.

help
Examples
> help
HELP:
Special keys:
  DEL, BS... delete previous character
  Ctrl-A  .... go to beginning of line
  Ctrl-E  .... go to end of line
  Ctrl-F  .... go forward one character
  Ctrl-B  .... go backward one character
  Ctrl-D  .... delete current character
  Ctrl-U, X. delete to beginning of line
  Ctrl-K  .... delete to end of line
  Ctrl-W  .... delete previous word
  Ctrl-T  .... transpose previous character
  Ctrl-P  .... go to previous line in history buffer
  Ctrl-N  .... go to next line in history buffer
  Ctrl-Z  .... return to root command prompt
  Tab, <SPACE> command-line completion
  Exit    .... go to next lower command prompt
  ?       .... list choices
Viewing Configurations

To view Cisco Wireless LAN controller options and settings, use the show commands.

show 802.11a

To display basic 802.11a options and settings, use the show 802.11a command.

show 802.11a
Syntax Description

show

Display configurations.

802.11a

802.11a configurations.

Defaults

None.

Examples
> show 802.11a
802.11a Network................................. Enabled
       802.11a Low Band......................... Enabled
       802.11a Mid Band......................... Enabled
       802.11a High Band........................ Enabled
802.11a Operational Rates
     802.11a 6M Rate............................ Mandatory
     802.11a 9M Rate............................ Supported
     802.11a 12M Rate........................... Mandatory
     802.11a 18M Rate........................... Supported
     802.11a 24M Rate........................... Mandatory
     802.11a 36M Rate........................... Supported
     802.11a 48M Rate........................... Supported
     802.11a 54M Rate........................... Supported
Beacon Interval................................. 100
CF Pollable mandatory........................... Disabled
CF Poll Request mandatory....................... Disabled
CFP Period...................................... 4
CFP Maximum Duration............................ 100
Default Channel................................. 36
Default Tx Power Level.......................... 1
DTPC Status..................................... Enabled
DTIM Period..................................... 10
Fragmentation Threshold......................... 2346
Long Retry Limit................................ 4
Maximum Rx Life Time............................ 512
Max Tx MSDU Life Time........................... 512
Medium Occupancy Limit.......................... 100
Pico-Cell Status................................ Disabled
RTS Threshold................................... 2347
Short Retry Limit............................... 7
TI Threshold.................................... -50
Related Commands

show 802.11b, show advanced 802.11a channel, show advanced 802.11a group, show advanced 802.11a logging, show advanced 802.11a monitor, show advanced 802.11a power, show advanced 802.11a profile, show advanced 802.11a summary

show 802.11a l2roam

To display Layer 2 client roaming information for the 802.11a network, use the show 802.11a l2roam command.

show 802.11a l2roam {rf-param | statistics mac_address}
Syntax Description

show

Display configurations.

802.11a

802.11a Cisco radio.

l2roam

Layer 2 client roaming configurations.

rf-param

Radio frequency parameters.

statistics

Layer 2 client roaming statistics.

mac_address

The MAC address of the client.

Defaults

None.

Examples
> show 802.11a l2roam rf-param
 
L2Roam 802.11a RF Parameters.....................
    Config Mode.................................. Default
    Minimum RSSI................................. -85
    Roam Hysteresis.............................. 2
    Scan Threshold............................... -72
    Transition time.............................. 5
> show 802.11a l2roam statistics
 
RadioMAC            Request  Report  Broadcast  Roam Report
-----------------   -------  ------  ---------  -----------
00:15:c7:2a:e8:f0      16      12       14           14
Related Commands

config 802.11a l2roam, show client roam-history, debug l2roam

show 802.11b

To display basic 802.11b/g options and settings, use the show 802.11b command.

show 802.11b
Syntax Description

show

Display configurations.

802.11b

802.11b/g configurations.

Defaults

None.

Examples
> show 802.11b
802.11b Network.................................. Enabled
11gSupport....................................... Enabled
802.11b/g Operational Rates
    802.11b/g 1M Rate............................ Mandatory
    802.11b/g 2M Rate............................ Mandatory
    802.11b/g 5.5M Rate.......................... Mandatory
    802.11b/g 11M Rate........................... Mandatory
    802.11g 6M Rate.............................. Supported
    802.11g 9M Rate.............................. Supported
    802.11g 12M Rate............................. Supported
    802.11g 18M Rate............................. Supported
    802.11g 24M Rate............................. Supported
    802.11g 36M Rate............................. Supported
    802.11g 48M Rate............................. Supported
    802.11g 54M Rate............................. Supported
Beacon Interval.................................. 100
CF Pollable mode................................. Disabled
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 1
Default Tx Power Level........................... 1
DTPC  Status..................................... Enabled
Call Admission Limit  ........................... 105
G711 CU Quantum ................................. 15
DTIM Period...................................... 1
ED Threshold..................................... -50
Fragmentation Threshold.......................... 2346
Long Retry Limit................................. 4
Maximum Rx Life Time............................. 512
Max Tx MSDU Life Time............................ 512
Medium Occupancy Limit........................... 100
PBCC mandatory................................... Disabled
Pico-Cell Status................................. Disabled
RTS Threshold.................................... 2347
Short Preamble mandatory......................... Enabled
Short Retry Limit................................ 7
Related Commands

show 802.11a, show advanced 802.11b channel, show advanced 802.11b group, show advanced 802.11b logging, show advanced 802.11b monitor, show advanced 802.11b txpower, show advanced 802.11b profile, show advanced 802.11b summary

show 802.11b l2roam

To display Layer 2 client roaming information for the 802.11b network, use the show 802.11b l2roam command.

show 802.11a l2roam {rf-param | statistics mac_address}
Syntax Description

show

Display configurations.

802.11b

802.11b Cisco radio.

l2roam

Layer 2 client roaming configurations.

rf-param

Radio frequency parameters.

statistics

Layer 2 client roaming statistics.

mac_address

The MAC address of the client.

Defaults

None.

Examples
> show 802.11b l2roam rf-param
 
L2Roam 802.11b RF Parameters.....................
    Config Mode.................................. Default
    Minimum RSSI................................. -85
    Roam Hysteresis.............................. 2
    Scan Threshold............................... -72
    Transition time.............................. 5
> show 802.11b l2roam statistics
 
RadioMAC            Request  Report  Broadcast  Roam Report
-----------------   -------  ------  ---------  -----------
00:15:c7:2a:e8:f0      16      12       14           14
Related Commands

config 802.11b l2roam, show client roam-history, debug l2roam

show 802.11h

To display basic 802.11h options and settings, use the show 802.11h command.

show 802.11h
Syntax Description

show

Display configurations.

802.11h

802.11h configurations.

Defaults

None.

Examples
> show 802.11h
802.11h ......................................... powerconstraint : 0
802.11h ......................................... channelswitch : Disable
802.11h ......................................... channelswitch mode : 0
Related Commands

show 802.11a, show 802.11b, config 802.11h

show aaa auth

To display the configuration settings for the AAA authentication server database search order, use the show aaa auth command.

show aaa auth
Syntax Description

This command has no arguments or keywords.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show aaa auth
Management authentication server order:
    1............................................ local
    2............................................ tacacs
Related Commands

config trapflags aaa, config aaa auth, config wlan aaa-override, debug aaa, debug aaa local-auth

show acl

To display the access control lists (ACLs) that are configured on the controller, use the show acl command.

show acl {summary | detailed acl_name}
Syntax Description

show acl

Command action.

summary

Display a summary of all ACLs configured on the controller.

detailed

Display detailed information about a specific ACL.

acl_name

ACL name up to 32 alphanumeric characters.

Defaults

None.

Examples
> show acl summary
ACL Name                         Applied
-------------------------------- -------
Pubs Only                        Yes
Mannina                          Yes
Related Commands

config interface acl

show acl cpu

To display the access control lists (ACLs) configured on the central processing unit (CPU), use the show acl cpu command.

show acl cpu
Syntax Description

show acl

Command action.

cpu

Displays a summary of all the ACLs configured on the CPU.

Command Default

None

Examples
> show acl cpu
CPU Acl Name................................
Wireless Traffic............................ Disabled
Wired Traffic............................... Disabled
Applied to NPU.............................. No
Related Commands

config acl cpu

SHOW ADVANCED 802.11A COMMANDS

Use the SHOW ADVANCED 802.11a commands to display advanced 802.11a configuration parameters.

show advanced 802.11a channel

To display the automatic channel assignment configuration and statistics, use the show advanced 802.11a channel command.

show advanced 802.11a channel
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

802.11a

802.11a network.

channel

Channel status.

Defaults

None.

Examples
> show advanced 802.11a channel
Automatic Channel Assignment
  Channel Assignment Mode........................ AUTO
  Channel Update Interval........................ 600 seconds
  Channel Update Contribution.................... SNI.
  Channel Assignment Leader...................... xx:xx:xx:xx:xx:xx
  Last Run....................................... 374 seconds ago
  Channel Energy Levels
    Minimum...................................... -84 dBm
    Average...................................... -84 dBm
    Maximum...................................... -84 dBm
  Channel Dwell Times
    Minimum...................................... 0 days, 19 h 07 m 57 s
    Average...................................... 0 days, 19 h 08 m 29 s
    Maximum...................................... 0 days, 19 h 09 m 11 s
Related Commands

config 802.11a channel

show advanced 802.11a group

To display the advanced 802.11a Cisco radio RF grouping, use the show advanced 802.11a group command.

show advanced 802.11a group
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

802.11a

802.11a network.

group

RF grouping values.

Defaults

None.

Examples
> show advanced 802.11a group
Radio RF Grouping
  802.11a Group Mode................................... AUTO
  802.11a Group Update Interval........................ 600 seconds
  802.11a Group Leader................................. xx:xx:xx:xx:xx:xx
    802.11a Group Member............................... xx:xx:xx:xx:xx:xx
  802.11a Last Run..................................... 133 seconds ago
Related Commands

config advanced 802.11a group-mode

show advanced 802.11a logging

To display advanced 802.11a RF event and performance logging, use the show advanced 802.11a logging command.

show advanced 802.11a logging
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

802.11a

802.11a network.

logging

RF event and performance logging.

Defaults

None.

Examples
> show advanced 802.11a logging
RF Event and Performance Logging
  Channel Update Logging......................... Off
  Coverage Profile Logging....................... Off
  Foreign Profile Logging........................ Off
  Load Profile Logging........................... Off
  Noise Profile Logging.......................... Off
  Performance Profile Logging.................... Off
  TxPower Update Logging......................... Off
Related Commands

config advanced 802.11a logging channel, config advanced 802.11a logging coverage, config advanced 802.11a logging foreign, config advanced 802.11a logging load, config advanced 802.11a logging noise, config advanced 802.11a logging performance, config advanced 802.11a logging power

show advanced 802.11a monitor

To display the advanced 802.11a default Cisco radio monitoring, use the show advanced 802.11a monitor command.

show advanced 802.11a monitor
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

802.11a

802.11a network.

monitor

Cisco radio monitoring values.

Defaults

None.

Examples
> show advanced 802.11a monitor
Default 802.11a AP monitoring
  802.11a Monitor Mode........................... enable
  802.11a Monitor Channels....................... Country channels
  802.11a AP Coverage Interval................... 180 seconds
  802.11a AP Load Interval....................... 60 seconds
  802.11a AP Noise Interval...................... 180 seconds
  802.11a AP Signal Strength Interval............ 60 seconds
Related Commands

config advanced 802.11a monitor coverage, config advanced 802.11a monitor load, config advanced 802.11a monitor noise, config advanced 802.11a monitor signal

show advanced 802.11a profile

To display the advanced 802.11a Cisco 1000 series lightweight access point performance profiles, use the show advanced 802.11a profile command.

show advanced 802.11a profile {global | Cisco_AP}
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

802.11a

802.11a network.

profile

Cisco radio performance profile.

global

All Cisco 1000 series lightweight access points.

Cisco_AP

Cisco 1000 series lightweight access point name.

Defaults

None.

Examples
> show advanced 802.11a profile global
Default 802.11a AP performance profiles
  802.11a Global Interference threshold.............. 10%
  802.11a Global noise threshold..................... -70 dBm
  802.11a Global RF utilization threshold............ 80%
  802.11a Global throughput threshold................ 1000000 bps
  802.11a Global clients threshold................... 12 clients
  802.11a Global coverage threshold.................. 12 dB
  802.11a Global coverage exception level............ 80%
  802.11a Global client minimum exception lev........ 3 clients
> show advanced 802.11a profile AP1
Cisco 1000 series lightweight access point performance profile not customized
This response indicates that the performance profile for this Cisco 1000 series lightweight access point is using the global defaults and has not been individually configured.

Related Commands

config advanced 802.11b profile clients, config advanced 802.11b profile coverage, config advanced 802.11b profile customize, config advanced 802.11b profile exception, config advanced 802.11b profile foreign, config advanced 802.11b profile level, config advanced 802.11b profile noise, config advanced 802.11b profile throughput, config advanced 802.11b profile utilization

show advanced 802.11a receiver

To display the configuration and statistics of the 802.11a receiver, use the show advanced 802.11a receiver command.

show advanced 802.11a receiver
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

802.11a

802.11a network.

receiver

Receiver.

Defaults

None.

Examples
> show advanced 802.11a receiver
802.11a Advanced Receiver Settings
  RxStart   : Signal Threshold........................... 15
  RxStart   : Signal Lamp Threshold...................... 5
  RxStart   : Preamble Power Threshold................... 2
  RxReStart : Signal Jump Status......................... Enabled
  RxReStart : Signal Jump Threshold...................... 10
  TxStomp : Low RSSI Status.............................. Enabled
  TxStomp : Low RSSI Threshold........................... 30
  TxStomp : Wrong BSSID Status........................... Enabled
  TxStomp : Wrong BSSID Data Only Status................. Enabled
  RxAbort : Raw Power Drop Status........................ Disabled
  RxAbort : Raw Power Drop Threshold..................... 10
  RxAbort : Low RSSI Status.............................. Disabled
  RxAbort : Low RSSI Threshold........................... 0
  RxAbort : Wrong BSSID Status........................... Disabled
  RxAbort : Wrong BSSID Data Only Status................. Disabled
Related Commands

config advanced 802.11a monitor coverage, config advanced 802.11a monitor load, config advanced 802.11a monitor noise, config advanced 802.11a monitor signal

show advanced 802.11a summary

To display the advanced 802.11a Cisco 1000 series lightweight access point name, channel, and transmit level summary, use the show advanced 802.11a summary command.

show advanced 802.11a summary
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

802.11a

802.11a network.

summary

Cisco 1000 series lightweight access point name, channel, and transmit level summary.

Defaults

None.

Examples
> show advanced 802.11a summary
AP Name                          Channel     TxPower Level
-------------------------------- ----------- -------------
AP03                                 36*           1*
AP02                                 52            5*
AP01                                 64            5
Note An asterisk (*) next to a channel number or power level indicates that it is being controlled by the global algorithm settings.

Related Commands

show advanced 802.11b summary

show advanced 802.11a txpower

To view the advanced 802.11a automatic transmit power assignment, use the show advanced 802.11a txpower command.

show advanced 802.11a txpower
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

802.11a

802.11a network.

txpower

Transmit power.

Defaults

None.

Examples
> show advanced 802.11a txpower
Automatic Transmit Power Assignment
  Transmit Power Assignment Mode.................. AUTO
  Transmit Power Update Interval.................. 600 seconds
  Transmit Power Threshold........................ -65 dBm
  Transmit Power Neighbor Count................... 3 APs
  Transmit Power Update Contribution.............. SN.
  Transmit Power Assignment Leader................ xx:xx:xx:xx:xx:xx
  Last Run........................................ 384 seconds ago
Related Commands

config advanced 802.11a txpower-update, config 802.11a txPower

SHOW ADVANCED 802.11B COMMANDS

Use the SHOW ADVANCED 802.11b commands show advanced 802.11b parameters.

show advanced 802.11b channel

To display the automatic channel assignment status and statistics, use the show advanced 802.11b channel command.

show advanced 802.11b channel
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

802.11b

802.11b/g network.

channel

Channel status.

Defaults

None.

Examples
> show advanced 802.11b channel
Automatic Channel Assignment
  Channel Assignment Mode........................ OFF
  Channel Update Interval........................ 600 seconds
  Channel Update Contribution.................... SNI.
  Channel Assignment Leader...................... xx:xx:xx:xx:xx:xx
  Last Run....................................... 157 seconds ago
  Channel Energy Levels
    Minimum...................................... unknown
    Average...................................... unknown
    Maximum...................................... unknown
  Channel Dwell Times
    Minimum...................................... unknown
    Average...................................... unknown
    Maximum...................................... unknown
Related Commands

config 802.11b channel

show advanced 802.11b group

To display the advanced 802.11b/g Cisco radio RF grouping, use the show advanced 802.11b group command.

show advanced 802.11b group
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

802.11b

802.11b/g network.

group

RF grouping values.

Defaults

None.

Examples
> show advanced 802.11b group
Radio RF Grouping
   802.11b Group Mode.............................. AUTO
   802.11b Group Update Interval................... 600 seconds
   802.11b Group Leader............................ xx:xx:xx:xx:xx:xx
     802.11b Group Member.......................... xx:xx:xx:xx:xx:xx
   802.11b Last Run................................ 511 seconds ago
Related Commands

config advanced 802.11b group-mode

show advanced 802.11b logging

To display advanced 802.11b/g RF event and performance logging, use the show advanced 802.11b logging command.

show advanced 802.11b logging
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

802.11b

802.11b network.

logging

RF event and performance logging.

Defaults

None.

Examples
> show advanced 802.11b logging
RF Event and Performance Logging
   Channel Update Logging........................... Off
   Coverage Profile Logging......................... Off
   Foreign Profile Logging.......................... Off
   Load Profile Logging............................. Off
   Noise Profile Logging............................ Off
   Performance Profile Logging...................... Off
   Transmit Power Update Logging.................... Off
Related Commands

config advanced 802.11b logging channel, config advanced 802.11b logging coverage, config advanced 802.11b logging foreign, config advanced 802.11b logging load, config advanced 802.11b logging noise, config advanced 802.11b logging performance, config advanced 802.11b logging power

show advanced 802.11b monitor

To display the advanced 802.11b/g default Cisco radio monitoring, use the show advanced 802.11b monitor command.

show advanced 802.11b monitor
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

802.11b

802.11b/g network.

monitor

Cisco radio monitoring values.

Defaults

None.

Examples
> show advanced 802.11b monitor
Default 802.11b AP monitoring
  802.11b Monitor Mode......................... enable
  802.11b Monitor Channels..................... Country channels
  802.11b AP Coverage Interval................. 180 seconds
  802.11b AP Load Interval..................... 60 seconds
  802.11b AP Noise Interval.................... 180 seconds
  802.11b AP Signal Strength Interval.......... 60 seconds
Related Commands

config advanced 802.11b monitor coverage, config advanced 802.11b monitor load, config advanced 802.11b monitor noise, config advanced 802.11b monitor signal

show advanced 802.11b profile

To display the advanced 802.11b/g Cisco radio performance profiles, use the show advanced 802.11b profile command.

show advanced 802.11b profile {global | Cisco_AP}
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

802.11b

802.11b/g network.

profile

Cisco 1000 series lightweight access point performance profile.

global

All Cisco 1000 series lightweight access points.

Cisco_AP

Cisco 1000 series lightweight access point name.

Defaults

None.

Examples
> show advanced 802.11b profile global
Default 802.11b AP performance profiles
   802.11b Global Interference threshold.............. 10%
   802.11b Global noise threshold..................... -70 dBm
   802.11b Global RF utilization threshold............ 80%
   802.11b Global throughput threshold................ 1000000 bps
   802.11b Global clients threshold................... 12 clients
   802.11b Global coverage threshold.................. 12 dB
   802.11b Global coverage exception level............ 80%
   802.11b Global client minimum exception lev........ 3 clients
> show advanced 802.11b profile AP1
Cisco 1000 series lightweight access point performance profile not customized
This response indicates that the performance profile for this Cisco 1000 series lightweight access point is using the global defaults and has not been individually configured.

Related Commands

config advanced 802.11b profile clients, config advanced 802.11b profile coverage, config advanced 802.11b profile customize, config advanced 802.11b profile exception, config advanced 802.11b profile foreign, config advanced 802.11b profile level, config advanced 802.11b profile noise, config advanced 802.11b profile throughput, config advanced 802.11b profile utilization

show advanced 802.11b receiver

To display the advanced 802.11b/g default Cisco radio receiver parameters, use the show advanced 802.11b receiver command.

show advanced 802.11b receiver
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

802.11b

802.11b/g network.

receiver

Cisco radio receiver values.

Defaults

None.

Examples
> show advanced 802.11b receiver
Default 802.11b Receiver Settings
  RxStart    :  Signal Threshold............... 15
  RxStart    :  Signal Jump Threshold.......... 5
  RxStart    :  Preamble Power Threshold....... 2
  RxRestart  :  Signal Jump Status............. Enabled
  RxRestart  :  Signal Jump Threshold.......... 10
  TxStomp    :  Low RSS Status.  .............. Disabled
  TxStomp    :  Low RSSI Threshold............. 37
  TxStomp    :  Wrong BSSID Status............. Disabled
  TxStomp    :  Wrong BSSID Data Only Status... Disabled
  RxAbort    :  Raw Power Drop Status.......... Disabled
  RxAbort    :  Raw Power Drop Threshold....... 0
  RxAbort    :  Low RSSI Status................ Enabled
  RxAbort    :  Low RSSI Threshold............. 0
  RxAbort    :  Wrong BSSID Status............. Disabled
  RxAbort    :  Wrong BSSID Data Only Status... Disabled
Related Commands

config advanced 802.11b monitor coverage, config advanced 802.11b monitor load, config advanced 802.11b monitor noise, config advanced 802.11b monitor signal

show advanced 802.11b summary

To display the advanced 802.11b/g Cisco 1000 series lightweight access point name, channel, and transmit level summary, use the show advanced 802.11b summary command.

show advanced 802.11b summary
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

802.11b

802.11b/g network.

summary

Cisco 1000 series lightweight access point name, channel, and transmit level summary.

Defaults

None.

Examples
> show advanced 802.11b summary
AP name               Channel      Txpower Level
-------------------   ----------   ------------
AP1                    11*            1*
AP2                    10*            4
AP3                    6*             2
Note Asterisks next to channel numbers or power levels indicate that they are being controlled by the global algorithm settings.

Related Commands

show advanced 802.11a summary

show advanced 802.11b txpower

To view the advanced 802.11b/g automatic transmit power assignment, use the show advanced 802.11b txpower command.

show advanced 802.11b txpower
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

802.11b

802.11b/g network.

txpower

Transmit power.

Defaults

None.

Examples
> show advanced 802.11b txpower
Automatic Transmit Power Assignment
  Transmit Power Assignment Mode................. AUTO
  Transmit Power Update Interval................. 600 seconds
  Transmit Power Threshold....................... -65 dBm
  Transmit Power Neighbor Count.................. 3 APs
  Transmit Power Update Contribution............. SNI.
  Transmit Power Assignment Leader............... xx:xx:xx:xx:xx:xx
  Last Run....................................... 427 seconds ago
Related Commands

config 802.11b txPower

show advanced client-handoff

To display the number of automatic client handoffs after retries, use the show advanced client-handoff command.

show advanced client-handoff
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

client-handoff

Advanced client handoff count.

Defaults

None.

Examples
> show advanced client-handoff
Client auto handoff after retries................  130
Related Commands

config advanced timers auth-timeout, config advanced timers rogue-ap

show advanced eap

To displayadvanced Extensible Authentication Potocol settings, use the show advanced eap command.

show advanced eap
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

eap

Advanced client handoff count.

Defaults

None.

Examples
> show advanced eap
EAP-Identity-Request Timeout (seconds)........... 1
EAP-Identity-Request Max Retries................. 20
EAP Key-Index for Dynamic WEP.................... 0
EAP-Request Timeout (seconds).................... 1
EAP-Request Max Retries.......................... 2
Related Commands

(tbd)

show advanced location

To display advanced location system information, use the show advanced location command.

show advanced location [detail mac_address | summary]
Syntax Description

detail

Displays detailed location information

mac_address

Specifies the MAC address of a client.

summary

Displays summary location information.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show advanced location summary
Advanced Location Summary :
 Algorithm used:                         Average
 Client RSSI expiry timeout:             10 sec, half life: 60 sec
 Calibrating Client RSSI expiry timeout: 10 sec, half life: 0 sec
 Rogue AP RSSI expiry timeout:           600 sec, half life: 120 sec
 RFID Tag RSSI expiry timeout:           60 sec, half life: 120 sec
> show advanced location advanced 32:16:13:1a:57:9f
...... TBD
Related Commands

Command

Description

config advanced location

Configures location settings.

show location summary

Displays information about defined locations.

show advanced max-1x-sessions

To display the maximum number of simultaneous 802.1x sessions allowed per access point, use the show advanced max-1x-sessions command.

show advanced max-1x-sessions
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

max-1x-sessions

Maximum number of simultaneous 802.1x sessions allowed per access point.

Defaults

None.

Examples
> show advanced max-1x-sessions
Max 802.1x session per AP at a given time........ 0
Related Commands

(tbd)

show advanced probe-limit

To display the number of probes sent to the WLAN controller per access point per client and the probe interval in milliseconds, use the show advanced probe-limit command.

show advanced probe-limit
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

probe-limit

Number of probes sent to the WLAN controller per access point per client and the probe interval in milliseconds.

Defaults

None.

Examples
> show advanced probe-limit
Probes sent to switch per AP slot per client ....  2
Probe interval in msec...........................  500
Related Commands

(tbd)

show advanced rate

To display whether control path rate limiting is enabled or disabled, use the show advanced rate command.

show advanced rate
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

rate

Control path rate limiting enabled or disabled.

Defaults

None.

Examples
> show advanced rate
Control Path Rate Limiting.......................  Disabled
Related Commands

(tbd)

show advanced send-disassoc-on-handoff

To display whether the WLAN controller disassociates clients after a handoff, use the show advanced send-disassoc-on-handoff command.

show advanced send-disassoc-on-handoff
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

send-disassoc-on-handoff

WLAN controller disassociates clients after a handoff enabled or disabled.

Defaults

None.

Examples
> show advanced send-disassoc-on-handoff
Send Disassociate on Handoff..................... Disabled
Related Commands

(tbd)

show advanced statistics

To display whether or not the Cisco Wireless LAN controller port statistics are enabled or disabled, use the show advanced statistics command.

show advanced statistics
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

statistics

Show Cisco Wireless LAN controller port statistics state.

Defaults

None.

Examples
> show advanced statistics
Switch port statistics...........................  Enabled
Related Commands

config advanced timers auth-timeout, config advanced timers rogue-ap

show advanced timers

To display the advanced mobility anchor, authentication response, and rogue access point entry timers, use the show advanced timers command.

show advanced timers
Syntax Description

show

Display configurations.

advanced

Advanced parameters.

timers

Advanced system timers.

Defaults

Shown below in examples.

Examples
> show advanced timers
Authentication Response Timeout (seconds)...... 10
Rogue Entry Timeout (seconds).................. 1200
AP Heart Beat Timeout (seconds)................ 30
AP Discovery Timeout (seconds)................. 10
EAP Request Timeout (seconds).................. 8        (only when EAP is enabled)
Related Commands

config advanced timers auth-timeout, config advanced timers rogue-ap

SHOW AP COMMANDS

Use the SHOW AP commands to show access point parameters.

show ap auto-rf

To display the auto-rf settings for a Cisco 1000 series lightweight access point, use the show ap auto-rf command.

show ap auto-rf {802.11a | 802.11b} Cisco_AP
Syntax Description

show

Display configurations.

ap auto-rf

Cisco radio.

{802.11a | 802.11b}

802.11a or 802.11b/g setting.

Cisco_AP

Cisco 1000 series lightweight access point name.

Defaults

None.

Examples
> show ap auto-rf 802.11a AP1
Number Of Slots.................................. 2
Rad Name......................................... AP03
MAC Address...................................... 00:0b:85:01:18:b7
  Radio Type..................................... RADIO_TYPE_80211a
  Noise Information
    Noise Profile................................ PASSED
    Channel 36...................................  -88 dBm
    Channel 40...................................  -86 dBm
    Channel 44...................................  -87 dBm
    Channel 48...................................  -85 dBm
    Channel 52...................................  -84 dBm
    Channel 56...................................  -83 dBm
    Channel 60...................................  -84 dBm
    Channel 64...................................  -85 dBm
  Interference Information
    Interference Profile......................... PASSED
    Channel 36...................................  -66 dBm @  1% busy
    Channel 40................................... -128 dBm @  0% busy
    Channel 44................................... -128 dBm @  0% busy
    Channel 48................................... -128 dBm @  0% busy
    Channel 52................................... -128 dBm @  0% busy
    Channel 56...................................  -73 dBm @  1% busy
    Channel 60...................................  -55 dBm @  1% busy
    Channel 64...................................  -69 dBm @  1% busy
  Load Information
    Load Profile................................. PASSED
    Receive Utilization.......................... 0%
    Transmit Utilization......................... 0%
    Channel Utilization.......................... 1%
    Attached Clients............................. 1 clients
  Coverage Information
    Coverage Profile............................. PASSED
    Failed Clients............................... 0 clients
  Client Signal Strengths
    RSSI -100 dBm................................ 0 clients
    RSSI  -92 dBm................................ 0 clients
    RSSI  -84 dBm................................ 0 clients
    RSSI  -76 dBm................................ 0 clients
    RSSI  -68 dBm................................ 0 clients
    RSSI  -60 dBm................................ 0 clients
    RSSI  -52 dBm................................ 0 clients
  Client Signal To Noise Ratios
    SNR    0 dBm................................. 0 clients
    SNR    5 dBm................................. 0 clients
    SNR   10 dBm................................. 0 clients
    SNR   15 dBm................................. 0 clients
    SNR   20 dBm................................. 0 clients
    SNR   25 dBm................................. 0 clients
    SNR   30 dBm................................. 0 clients
    SNR   35 dBm................................. 0 clients
    SNR   40 dBm................................. 0 clients
    SNR   45 dBm................................. 0 clients
  Nearby RADs
    RAD 00:0b:85:01:05:08 slot 0.................  -46 dBm on 10.1.30.170
    RAD 00:0b:85:01:12:65 slot 0.................  -24 dBm on 10.1.30.170
  Channel Assignment Information
    Current Channel Average Energy...............  -86 dBm 
    Previous Channel Average Energy..............  -75 dBm 
    Channel Change Count.........................  109 
    Last Channel Change Time..................... Wed Sep 29 12:53e:34 2004
    Recommended Best Channel..................... 44 
  RF Parameter Recommendations
    Power Level.................................. 1
    RTS/CTS Threshold............................ 2347
    Fragmentation Threshold...................... 2346
    Antenna Pattern.............................. 0
Related Commands

config 802.11a antenna, config 802.11b antenna, config cell

show ap bmode

To display the backhaul mode for a Cisco 1030 or 1500 Series lightweight access point deployed in bridging or mesh mode, use the show ap bhmode command.

show ap bhmode Cisco_AP
Syntax Description

show

Display configurations.

ap

Cisco radio.

bhmode

Display the mesh or bridging backhaul mode for a Cisco 1030 or 1500 Series lightweight access point.

Cisco_AP

Cisco 1000 series lightweight access point name.

Defaults

None.

Examples
> show ap bhmode AP02
Related Commands

config ap stats-timer

show ap bhrate

To display the backhaul rate for a Cisco 1030 or 1500 Series lightweight access point deployed in bridging or mesh mode, use the show ap bhrate command.

show ap bhrate Cisco_AP
Syntax Description

show

Display configurations.

ap

Cisco radio.

bhrate

Display the mesh or bridging backhaul rate for a Cisco 1030 or 1500 Series lightweight access point.

Cisco_AP

Cisco 1000 series lightweight access point name.

Defaults

None.

Examples
> show ap bhrate AP02
Related Commands

config ap stats-timer

show ap ccx rm

To display an access point's ccx radio management status information, use the show ap ccx rm command.

show ap ccxrm ap_name status
Syntax Description

ap_name

Specified the access point name.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show ap ccx rm AP1240-21ac status
A Radio
Channel Load Request ..................... Disabled
Noise Histogram Request .................. Disabled
Beacon Request ........................... Disabled
Frame Request ............................ Disabled
Interval ................................. 60
Iteration ................................ 10
G Radio
Channel Load Request ..................... Disabled
Noise Histogram Request .................. Disabled
Beacon Request ........................... Disabled
Frame Request ............................ Disabled
Interval ................................. 60
Iteration ................................ 10
Related Commands

Command

Description

show client ccx

Displays client ccx information.

show ap cdp neighbors detail

This command is used display information regarding the access point's CDP neighbors ----TBD.

show ap cdp neighbors detail [all | ap_name]
Syntax Description

all

Displays the CDP neighbors for all the access points.

ap_name

Displays the CDP neighbors for the specified access point.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show ap cdp neighbors all
AP Name:A10-1020
AP IP address:10.00.231.100
-------------------------
Device ID: Switch
Entry address(es): 10.00.231.2
Platform: cisco WS-C3750-24P,  Capabilities: Router Switch IGMP
Interface: enet,  Port ID (outgoing port): FastEthernet1/0/23 Holdtime : 180 sec
Version :
Cisco Internetwork Operating System Software  IOS (tm) C3750 Software (C3750-I9- M),  
Version 12.2(20)SE4, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2005 by Cisco  Systems, 
Inc. Compiled Sun 09-Jan-05 00:09 by antonino
advertisement version: 2
Related Commands

Command

Description

TBD

TBD

TBD

show ap config

To display the detailed configuration for a lightweight access point, use the show ap config command.

show ap config {802.11a | 802.11b | general} Cisco_AP
Syntax Description

802.11a

Displays the 802.11a radio settings.

802.11b

Displays the 802.11b/g radio settings.

general

Displays general access point settings.

Cisco_AP

Specifies the lightweight access point name.

Defaults

None.

Examples
> show ap config 802.11a AP02
Cisco AP Identifier.............................. 0
Cisco AP Name.................................... AP02
AP Regulatory Domain............................. Unconfigured
Switch Port Number .............................. 1
MAC Address...................................... 00:0b:85:18:b6:50
IP Address Configuration......................... DHCP
IP Address....................................... 1.100.49.240
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 1.100.49.1
Cisco AP Location................................ default-location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch............................. Cisco_32:ab:63
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W  Version .................................... 3.1.61.0
Boot  Version ................................... 1.2.59.6
Stats Re--More-- or (q)uit
porting Period .................................. 180
LED State........................................ Enabled
ILP Pre Standard Switch.......................... Disabled
ILP Power Injector............................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AS-1200
AP Serial Number................................. 044110223A
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot  0
    Radio Type................................... RADIO_TYPE_80211a
    Administrative State ........................ ADMIN_ENABLED
    Operation State ............................. UP
    WLAN Override................................ Disabled
    CellId ...................................... 0
    Station Configuration
      Configuration ............................. AUTOMATIC
      Number Of WLANs ........................... 1
      Medium Occupancy Limit .................... 100
      CFP Period ................................ 4
      CFP MaxDuration ........................... 60
      BSSID ..................................... 00:0b:85:18:b6:50
    Operation Rate Set
        6000 Kilo Bits........................... MANDATORY
        9000 Kilo Bits........................... SUPPORTED
        12000 Kilo Bits.......................... MANDATORY
        18000 Kilo Bits.......................... SUPPORTED
        24000 Kilo Bits.......................... MANDATORY
        36000 Kilo Bits.......................... SUPPORTED
        48000 Kilo Bits.......................... SUPPORTED
        54000 Kilo Bits.......................... SUPPORTED
      Beacon Period ............................. 100
      DTIM Period ............................... 1
      Fragmentation Threshold ................... 2346
      Multi Domain Capability Implemented ....... TRUE
      Multi Domain Capability Enabled ........... TRUE
      Country String ............................ US
    Multi Domain Capability
      Configuration ............................. AUTOMATIC
      First Chan Num ............................ 36
      Number Of Channels ........................ 4
    MAC Operation Parameters
      Configuration ............................. AUTOMATIC
      RTS Threshold ............................. 2347
      Short Retry Limit ......................... 7
      Long Retry Limit .......................... 4
      Fragmentation Threshold ................... 2346
      Maximum Tx MSDU Life Time ................. 512
      Maximum Rx Life Time ...................... 512
    Tx Power
      Num Of Supported Power Levels ............. 5
      Tx Power Level 1 .......................... 18 dBm
      Tx Power Level 2 .......................... 15 dBm
      Tx Power Level 3........................... 12 dBm
      Tx Power Level 4 .......................... 9 dBm
      Tx Power Level 5 .......................... 6 dBm
      Tx Power Configuration .................... CUSTOMIZED
      Current Tx Power Level..................... 5
    Phy OFDM parameters
      Configuration ............................. AUTOMATIC
      Current Channel ........................... 36
      TI Threshold .............................. -50
      Antenna Type............................... INTERNAL_ANTENNA
      Internal Antenna Gain (in .5 dBm units).... 11
      AntennaMode................................ ANTENNA_OMNI
    Performance Profile Parameters
      Configuration ............................. AUTOMATIC
      Interference threshold..................... 10%
      Noise threshold............................  -70 dBm
      RF utilization threshold................... 80%
      Data-rate threshold........................ 1000000 bps
      Client threshold........................... 12 clients
      Coverage SNR threshold..................... 16 dB
      Coverage exception level................... 25%
      Client minimum exception level............. 3 clients
    Rogue Containment Information
    Containment Count............................ 0
> show ap config 802.11b AP02
Cisco AP Identifier.............................. 0
Cisco AP Name.................................... AP02
AP Regulatory Domain............................. Unconfigured
Switch Port Number .............................. 1
MAC Address...................................... 00:0b:85:18:b6:50
IP Address Configuration......................... DHCP
IP Address....................................... 1.100.49.240
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 1.100.49.1
Cisco AP Location................................ default-location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch............................. Cisco_32:ab:63
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W  Version .................................... 3.1.61.0
Boot  Version ................................... 1.2.59.6
Stats Reporting Period .......................... 180
LED State........................................ Enabled
ILP Pre Standard Switch.......................... Disabled
ILP Power Injector............................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AS-1200
AP Serial Number................................. 044110223A
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot  1
    Radio Type................................... RADIO_TYPE_80211g
    Administrative State ........................ ADMIN_ENABLED
    Operation State ............................. UP
    WLAN Override ............................... Disabled
    CellId ...................................... 0
    Station Configuration
      Configuration ............................. AUTOMATIC
      Number Of WLANs ........................... 1
      Medium Occupancy Limit .................... 100
      CFP Period ................................ 4
      CFP MaxDuration ........................... 60
      BSSID ..................................... 00:0b:85:18:b6:50
      Operation Rate Set
        1000 Kilo Bits........................... MANDATORY
        2000 Kilo Bits........................... MANDATORY
        5500 Kilo Bits........................... MANDATORY
        11000 Kilo Bits.......................... MANDATORY
        6000 Kilo Bits........................... SUPPORTED
        9000 Kilo Bits........................... SUPPORTED
        12000 Kilo Bits.......................... SUPPORTED
        18000 Kilo Bits.......................... SUPPORTED
        24000 Kilo Bits.......................... SUPPORTED
        36000 Kilo Bits.......................... SUPPORTED
        48000 Kilo Bits.......................... SUPPORTED
        54000 Kilo Bits.......................... SUPPORTED
      Beacon Period ............................. 100
      DTIM Period ............................... 1
      Fragmentation Threshold ................... 2346
      Multi Domain Capability Implemented ....... TRUE
      Multi Domain Capability Enabled ........... TRUE
      Country String ............................ US
    Multi Domain Capability
      Configuration ............................. AUTOMATIC
      First Chan Num ............................ 1
      Number Of Channels ........................ 11
    MAC Operation Parameters
      Configuration ............................. AUTOMATIC
      RTS Threshold ............................. 2347
      Short Retry Limit ......................... 7
      Long Retry Limit .......................... 4
      Fragmentation Threshold ................... 2346
      Maximum Tx MSDU Life Time ................. 512
      Maximum Rx Life Time....................... 512
    Tx Power
      Num Of Supported Power Levels.............. 5
      Tx Power Level 1 .......................... 17 dBm
      Tx Power Level 2........................... 14 dBm
      Tx Power Level 3........................... 11 dBm
      Tx Power Level 4........................... 8 dBm
      Tx Power Level 5........................... 5 dBm
      Tx Power Configuration..................... CUSTOMIZED
      Current Tx Power Level..................... 5
    Phy OFDM parameters
      Configuration.............................. CUSTOMIZED
      Current Channel............................ 1
      TI Threshold............................... -50
      Antenna Type............................... INTERNAL_ANTENNA
      Internal Antenna Gain (in5 dBm units)...... 11
      Diversity.................................. DIVERSITY_ENABLED
    Performance Profile Parameters
      Configuration.............................. AUTOMATIC
      Interference threshold..................... 10%
      Noise threshold............................  -70 dBm
      RF utilization threshold................... 80%
      Data-rate threshold........................ 1000000 bps
      Client threshold........................... 12 clients
      Coverage SNR threshold..................... 12 dB
      Coverage exception level................... 25%
      Client minimum exception level............. 3 clients
    Rogue Containment Information
    Containment Count............................ 0
> show ap config general AP02
Cisco AP Identifier.............................. 0
Cisco AP Name.................................... AP02
AP Regulatory Domain............................. Unconfigured
Switch Port Number............................... 1
MAC Address...................................... xx:xx:xx:xx:xx:xx
IP Address Configuration......................... DHCP
IP Address....................................... 1.100.49.240
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 1.100.49.1
Cisco AP Location................................ default-location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch............................. Cisco_32:ab:63
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State............................. ADMIN_ENABLED
Operation State.................................. REGISTERED
Mirroring Mode................................... Disabled
AP Mode.......................................... Local
Remote AP Debug.................................. Disabled
S/W  Version..................................... 3.1.61.0
Boot  Version.................................... 1.2.59.6
porting Period................................... 180
LED State........................................ Enabled
ILP Pre Standard Switch.......................... Disabled
ILP Power Injector............................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AS-1200
AP Serial Number................................. 044110223A
AP Certificate Type.............................. Manufacture Installed
Related Commands

config 802.11a antenna

Configures the access point's 802.11a antennas settings.

config 802.11b antenna

Configures the access point's 802.11b antennas settings.

config 802.11a enable

Enables the access point's 802.11a radio.

config 802.11b enable

Enables the access point's 802.11b/g radio

show ap core-dump

To display the memory core dump setting for a lightweight access point, use the show ap core-dump command.

show ap core-dump Cisco_AP
Syntax Description

Cisco_AP

Cisco 1000 series lightweight access point name.

Defaults

None.

Examples
> show ap core-dump AP02
Related Commands

config ap core-dump

Configures the access point's memory core dump settings.

show ap crash-file

To display the list of both crash and radio core dump files generated by lightweight access points, use the show ap crash-file command.

show ap crash-file
Syntax Description

This command has no arguments or keywords.

Defaults

This command has no defaults.

Examples
> show ap crash-file
Related Commands

config ap crash-file

Configures the access point's crash-file settings.

show ap inventory

This command is used display inventory information for an access point. ----TBD.

show ap ap inventory ap_name]
Syntax Description

ap_name

Displays the inventory for the specified access point.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show ap inventory test101
----- TBD

Related Commands

Command

Description

TBD

TBD

TBD

show ap stats

To display the statistics for a Cisco 1000 series lightweight access point, use the show ap stats command.

show ap stats {802.11a | 802.11b} Cisco_AP
Syntax Description

show

Display configurations.

ap stats

Cisco radio.

802.11a

802.11a statistics.

802.11b

802.11b/g statistics.

Cisco_AP

Cisco 1000 series lightweight access point name.

Defaults

None.

Examples
> show ap stats 802.11b AP02
Number Of Slots.................................. 2
AP Name.......................................... AP02
MAC Address...................................... 00:0b:85:18:b6:50
  Radio Type..................................... RADIO_TYPE_80211a
  Stats Information
    Number of Users.............................. 0
    TxFragmentCount.............................. 1679
    MulticastTxFrameCnt.......................... 1260
    FailedCount.................................. 15892
    RetryCount................................... 331
    MultipleRetryCount........................... 0
    FrameDuplicateCount.......................... 0
    RtsSuccessCount.............................. 0
    RtsFailureCount.............................. 0
    AckFailureCount.............................. 80212
    RxFragmentCount.............................. 248671
    MulticastRxFrameCnt.......................... 0
    FcsErrorCount................................ 105968
    TxFrameCount................................. 1679
    WepUndecryptableCount........................ 0
Related Commands

config ap enable

Enables a lightweight access point.

show ap summary

Displays a list of access points connected to the controller.

show ap summary

To display a summary of all lightweight access points attached to the controller, use the show ap summary command. A list containing each lightweight access point name, number of slots, manufacturer, MAC address, location and the controller port number is displayed.

show ap summary
Syntax Description

show

Display configurations.

ap

All Cisco 1000 series lightweight access points.

summary

Summary of all Cisco 1000 series lightweight access points.

Defaults

None.

Examples
> show ap summary
Number of APs.................................... 3
AP Name

Slots

AP Model

Ethernet MAC

Location

Port

Country

---------------

-----

---------

-----------------

----------------

----

-------

ap1020:5f:be:90

2

AP1020

00:0c:85:5f:32:90

default location

29

US

ap1131:3e:ba:10

2

AIR-LAP 1131

00:0b:81:2c:be:01

default location

29

US

ap1242:df:ac:15

2

AIR-LAP1242

00:0e:15:3d:fd:24

default location

29

US
Related Commands

show advanced 802.11a summary

Displays advanced 802.11a radio configuration settings and statistics.

show advanced 802.11b summary

Displays advanced 802.11b/g radio configuration settings and statistics.

config ap enable

Enables an access point's 802.11 radio.

show ap wlan

To display whether or not a Cisco Wireless LAN controller radio is in wireless LAN override mode (as described in the related product guide), use the show ap wlan command.

show ap wlan {802.11a | 802.11b} Cisco_AP
Syntax Description

show

Display configurations.

ap

All Cisco 1000 series lightweight access points.

wlan

Wireless LAN parameter.

802.11a

Displays the access point's 802.11a radio statistics.

802.11b

Displays the access point's 802.11b radio statistics.

ap_name

Specifies the lightweight access point name.

Defaults

None.

Examples
> show ap wlan 802.11a AP01
AP has following wlan Id's configured as override wlanId
        Wlan Id:........................................ 3
> show ap wlan 802.11a AP15
Cisco AP is not in override mode. 
Related Commands

show ap summary

Displays summary information on all access points connected to the controller.

config ap wlan enable

Enables a wireless LAN override on an access point.

show arp switch

To display the Cisco Wireless LAN controller MAC addresses, IP Addresses, and port types, use the show arp switch command.

show arp switch
Syntax Description

show

Display configurations.

arp

arp MAC addresses, IP Addresses, and port types.

switch

Cisco Wireless LAN controller parameters.

Defaults

None.

Examples
> show arp switch
MAC Address          IP Address         Port      VLAN      Type
------------------- ---------------- ------------ ---- -------------------
xx:xx:xx:xx:xx:xx   xxx.xxx.xxx.xxx  service port    1         
xx:xx:xx:xx:xx:xx   xxx.xxx.xxx.xxx  service port               
xx:xx:xx:xx:xx:xx   xxx.xxx.xxx.xxx  service port               
Related Commands

debug arp

show auth-list

To display the access point authorization list, use the show auth-list command.

show auth-list
Syntax Description

show

Display configurations.

auth-list

Display access point authorization list.

Defaults

None.

Examples
> show auth-list
Authorize APs against AAA...................... disabled
Allow APs with Self-signed Certificate (SSC)... disabled
Mac Addr                  Cert Type    Key Hash
-----------------------   ----------   ------------------------------------------
xx:xx:xx:xx:xx:xx         MIC
Related Commands

config auth-list

show boot

Each Cisco Wireless LAN controller retains one primary and one backup operating system software load in non-volatile RAM. This allows operators to have the Cisco Wireless LAN controllers boot off the primary load (default), or revert to the backup load when desired. To display the primary and backup software build numbers with an indication of which is active, use the show boot command.

show boot
Syntax Description

show

Display configurations.

boot

Software bootable versions.

Defaults

None.

Examples
> show boot
Primary Boot Image............................... 3.2.13.0 (active)
Backup Boot Image................................ 3.2.15.0
Related Commands

config exclusionlist add, config exclusionlist delete, config exclusionlist description, show client

SHOW CERTIFICATE COMMANDS

Use the SHOW CERTIFICATE commands to display certificate settings.

show certificate compatibility

To display whether or not certificates are verified as compatible in the Cisco Wireless LAN controller, use the show certificate compatibility command.

show certificate compatibility
Syntax Description

show

Display configurations.

certificate

All certificates.

compatibility

Compatibility of certificates.

Defaults

None.

Examples
> show certificate compatibility
Certificate compatibility mode:................ off
Related Commands

show certificate summary

show certificate summary

To display a summary of all certificates active in the Cisco Wireless LAN controller, use the show certificate summary command.

show certificate summary
Syntax Description

show

Display configurations.

certificate

All certificates.

summary

Synopsis of all certificates.

Defaults

None.

Examples
> show certificate summary
Web Administration Certificate................. Locally Generated
Web Authentication Certificate................. Locally Generated
Certificate compatibility mode:................ off
Related Commands

show certificate compatibility

SHOW CLIENT COMMANDS

Use the SHOW CLIENT commands to display client settings.

show client ap

To display the clients on a Cisco 1000 series lightweight access point, use the show client ap command.

Note The show client ap command may list the status of automatically disabled clients. Use the show exclusionlist command to view clients on the exclusion list (blacklisted).

show client ap {802.11a | 802.11b} Cisco_AP
Syntax Description

show

Display configurations.

client ap

Cisco radio.

802.11a

802.11a clients.

802.11b

802.11b/g clients.

Cisco_AP

Cisco 1000 series lightweight access point name.

Defaults

None.

Examples
> show client ap 802.11b AP1
MAC Address        AP Id   Status         WLAN Id    Authenticated
-----------------  ------  -------------  ---------  -------------
xx:xx:xx:xx:xx:xx      1   Associated     1          No
Related Commands

show client detail, show client summary, show client username, show exclusionlist

show client ccx log-response

This command is used display ----TBD.

show client ccx log-response [ roam | rsna | syslog] client_mac_address
Syntax Description

roam

Displays CCX client roaming log response.

rsna

Display CCX client RSNA log response.

syslog

Display CCX client system log response.

client_mac_address

Displays the inventory for the specified access point.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> config client ccx log-request syslog 00:40:96:a8:f7:98 
> show client ccx log-response syslog 00:40:96:a8:f7:98 
Tue Oct 05 13:05:21 2006  
SysLog Response LogID=1: Status=Successful
Event Timestamp=121212121212
Client SysLog = 'This is a test syslog 2'
Event Timestamp=121212121212
Client SysLog = 'This is a test syslog 1'
Tue Oct 05 13:04:04 2006  
SysLog Request LogID=1
> config client ccx log-request roam 00:40:96:a8:f7:98
> show client ccx log-response roam 00:40:96:a8:f7:98
Thu Jun 22 11:55:14 2006 
Roaming Response LogID=20: Status=Successful
Event Timestamp=121212121212 
Source BSSID=00:40:96:a8:f7:98, Target BSSID=00:0b:85:23:26:70, 
Transition Time=100(ms) 
Transition Reason: Unspecified Transition Result: Success
Thu Jun 22 11:55:04 2006  
Roaming Request LogID=20
Thu Jun 22 11:54:54 2006  
Roaming Response LogID=19: Status=Successful
Event Timestamp=121212121212
Source BSSID=00:40:96:a8:f7:98, Target BSSID=00:0b:85:23:26:70,
Transition Time=100(ms) 
Transition Reason: Unspecified Transition Result: Success
Thu Jun 22 11:54:33 2006  Roaming Request LogID=19
> config client ccx log-request rsna 00:40:96:a8:f7:98
> show client ccx log-response rsna 00:40:96:a8:f7:98
Tue Oct 05 11:06:48 2006  
RSNA Response LogID=2: Status=Successful
Event Timestamp=242424242424
Target BSSID=00:0b:85:23:26:70
RSNA Version=1
Group Cipher Suite=00-0f-ac-01 
Pairwise Cipher Suite Count = 2
Pairwise Cipher Suite 0 = 00-0f-ac-02 
Pairwise Cipher Suite 1 = 00-0f-ac-04 
AKM Suite Count = 2 
KM Suite 0 = 00-0f-ac-01 
KM Suite 1 = 00-0f-ac-02 
SN Capability = 0x1 
PMKID Count = 2 
PMKID 0 = 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 
PMKID 1 = 0a 0b 0c 0d 0e 0f 17 18 19 20 1a 1b 1c 1d 1e 1f 
802.11i Auth Type: EAP_FAST
RSNA Result: Success
Tue Oct 05 11:05:48 2006  
RSNA Request LogID=2
Related Commands

Command

Description

config client ccx log-request

Configures the CCX client log request.

show client ccx rm

This command is used display ccx client information ----TBD.

show client ccx rm client_MAC [ status |
report ( chan-load | noise-hist | frame request | beacon | frame )]
Syntax Description

client_MAC

Specifies the client MAC address.

status

Displays client ccx radio management status information.

report

Displays client ccx radio management report.

chan-load

Displays radio management channel load reports.

noise-hist

Displays radio management noise histogram reports.

beacon

Displays radio managemant beacon load reports.

frame

Displays radio management frame reports.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show client ccx rm 00:40:96:15:21:ac status
Client Mac Address............................... 00:40:96:15:21:ac 
Channel Load Request............................. Enabled 
Noise Histogram Request.......................... Enabled 
Beacon Request................................... Enabled 
Frame Request.................................... Enabled 
Interval......................................... 30 
Iteration........................................... 10
> show client ccx rm 00:40:96:15:21:ac report chan-load

Channel Load Report
Client Mac Address............................... 00:40:96:ae:53:bc
Timestamp........................................ 788751121
Incapable Flag................................... On
Refused Flag........................................ On

Chan CCA Busy Fraction
-----------------------
1 194
2 86
3 103
4 0
5 178
6 82
7 103
8 95
9 	13  
10 	222 
11 	75 
> show client ccx rm 00:40:96:15:21:ac report noise-hist
Noise Histogram Report
Client Mac Address............................... 00:40:96:15:21:ac
Timestamp........................................ 4294967295
Incapable Flag................................... Off
Refused Flag........................................ Off
Chan RPI0 RPI1 RPI2 RPI3 RPI4 RPI5 RPI6 RPI7 
> show client ccx rm 00:40:96:ae:53:bc report beacon
Beacon Report
Client Mac Address............................... 00:40:96:ae:53:bc
Timestamp....................................... 788853242
Incapable Flag.................................. On
Refused Flag....................................... On

Channel No...................................... 3
Phy Type........................................ ERP
Received signal Power........................... -80dbm
BSSID........................................... 00:12:7f:50:93:10
Parent TFS...................................... bc729d5e
Parent TFS...................................... 42f637ec02000000
Beacon Interval................................. 100
Capability Information............................. 0401
 
Channel No...................................... 7  
Phy Type........................................ ERP 
Received signal Power........................... -62dbm 
BSSID........................................... 00:12:44:b3:b9:e0 
Parent TFS...................................... 4f46aa5e 
Parent TFS...................................... bd1ba60f00000000 
Beacon Interval................................. 100 
Capability Information............................. 0421
> show client ccx rm 00:40:96:ae:53:bc report frame
Frame Report
Client Mac Address.............................. 00:40:96:ae:53:bc
Timestamp....................................... 789140437
Incapable Flag.................................. On
Refused Flag....................................... On
Chan Tx Address Bssid RcxSigPwr Frame Count 
--------------------------------------------------------------
Related Commands

Command

Description

TBD

TBD

show client ccx stats-report

To display the CCX statistics report from a specified client device, use the show slient ccx stats-report command.

show client ccx stats-report client_mac_address
Syntax Description

client_mac_address

Displays the MAC address for the specified client device.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> config client ccx stats-request 1 dot11 00:40:96:a8:f7:98 
> show client ccx stats-report 00:40:96:a8:f7:98 
Measurement duration = 1
dot11TransmittedFragmentCount       = 1
dot11MulticastTransmittedFrameCount = 2
dot11FailedCount                    = 3
dot11RetryCount                     = 4
dot11MultipleRetryCount             = 5
dot11FrameDuplicateCount            = 6
dot11RTSSuccessCount                = 7
dot11RTSFailureCount                = 8
dot11ACKFailureCount                = 9
dot11ReceivedFragmentCount          = 10
dot11MulticastReceivedFrameCount    = 11
dot11FCSErrorCount                  = 12
dot11TransmittedFrameCount          = 13
Related Commands

Command

Description

config client ccx stats-request

Configures the CCX client statistics request.

show client detail

To display detailed information for a client on a Cisco 1000 series lightweight access point, use the show client detail command.

Note The show client ap command may list the status of automatically disabled clients. Use the show exclusionlist command to view clients on the exclusion list (blacklisted).

show client detail MAC
Syntax Description

show

Display configurations.

client

802.11a or 802.11b/g client.

detail

Connectivity information.

MAC

MAC address of the specific client.

Defaults

None.

Examples
> show client detail 00:0c:41:07:33:a6
Client MAC Address............................... xx:xx:xx:xx:xx:xx
Client Username.................................. N/A
AP MAC Address................................... xx:xx:xx:xx:xx:xx
Client State..................................... Associated
Wireless LAN Id.................................. 1
IP Address....................................... Unknown
Association Id................................... 1
Authentication Algorithm......................... Shared Key
Reason Code...................................... 0
Status Code...................................... 0
Session Timeout.................................. 0
Mirroring........................................ Disabled
QoS Level........................................ Gold
Diff Serv Code Point (DSPC)...................... disabled
802.1P Priority Tag.............................. disabled
Mobility State................................... Local
Mobility Move Count.............................. 0
Security Policy Completed........................ No
Policy Manager State............................. DHCP_REQD
Policy Manager Rule Created...................... No
NPU Fast Notified................................ Yes
Policy Type...................................... N/A
Encryption Cipher................................ WEP (104 bits)
EAP Type......................................... Unknown
Interface........................................ management
VLAN............................................. 0
Client Capabilities:
      CF Pollable................................ Not implemented
      CF Poll Request............................ Not implemented
      Short Preamble............................. Not implemented
      PBCC....................................... Not implemented
      Channel Agility............................ Not implemented
      Listen Interval............................ 0
Client Statistics:
      Number of Bytes Received................... 0
      Number of Bytes Sent....................... 0
      Number of Packets Received................. 0
      Number of Packets Sent..................... 0
      Number of Policy Errors.................... 0
      Radio Signal Strength Indicator............ Unavailable
      Signal to Noise Ratio...................... Unavailable
Nearby AP Statistics:
      AP03(slot 0) 24643 seconds ago............. -11 dBm
Related Commands

show client ap, show client summary, show client username, show exclusionlist

show client location-calibration summary

To display client location calibration summary information, use the show client lcoation-calibration summary command. ...... TBD.....

show client location-calibration summary
Syntax Description

This command has no arguments or keywords.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show client location-calibration summary
PUT TABLE HER ***************
MAC Address Inerval 
----------- ----------
10:10:10:10:10:10 60
21:21:21:21:21:21 45
Related Commands

Command

Description

TBD

TBD

TBD

show client report

To display detail client nformation, use the show client detail command.

show client detail
Syntax Description

This command has no arguments or keywords.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show client detail 00:14:6c:0a:57:77
Client MAC Address............................... 00:14:6c:0a:57:77
Client Username ................................. N/A
AP MAC Address................................... 00:0b:85:0e:19:a0
Client State..................................... Diagnostics
Wireless LAN Id.................................. 1
BSSID............................................ 00:0b:85:0e:19:a0
Channel.......................................... 40
IP Address....................................... 1.100.150.53
Association Id................................... 1
Authentication Algorithm......................... Open System
Reason Code...................................... 0
Status Code...................................... 0
Session Timeout.................................. 1800
Client CCX version............................... CCXv5
Re-Authentication Timeout........................ 1800
QoS Level........................................ Silver
Related CommandsNumber of Clients................................ 2

Related Commands

Related CommandsMAC Address AP Name Status WLAN Auth Protocol Port

Related Commands----------------- ----------------- ------------- ---- ---- -------- ----

Related Commands

Related Commands00:13:02:1e:9b:c6 ap:0e:19:a0 Probing N/A No 802.11a 1

Related Commands00:14:6c:0a:57:77 ap:0e:19:a0 Diagnostics 1 Yes 802.11a 1

Related Commands

Command

Description

TBD

TBD

TBD

show client summary

To display a summary of clients associated with a Cisco 1000 series lightweight access point, use the show client summary command.

Note The show client ap command may list the status of automatically disabled clients. Use the show exclusionlist command to view clients on the exclusion list (blacklisted).

show client summary
Syntax Description

show

Display configurations.

client

802.11a or 802.11b/g client.

summary

All attached clients.

Defaults

None.

Examples
> show client summary
Number of Clients................................ 24
MAC Address        AP Name            Status         WLAN  Auth  Protocol  Port
-----------------  -----------------  -------------  ----  ----  --------  ----
xx:xx:xx:xx:xx:xx  AP02               Probing        N/A   No    802.11a   1
xx:xx:xx:xx:xx:xx  AP02               Probing        N/A   No    802.11a   1
xx:xx:xx:xx:xx:xx  AP02               Probing        N/A   No    802.11b   1
xx:xx:xx:xx:xx:xx  AP02               Probing        N/A   No    802.11a   1
xx:xx:xx:xx:xx:xx  AP02               Probing        N/A   No    802.11b   1
xx:xx:xx:xx:xx:xx  AP02               Probing        N/A   No    802.11b   1
xx:xx:xx:xx:xx:xx  AP02               Probing        N/A   No    802.11b   1
xx:xx:xx:xx:xx:xx  AP02               Probing        N/A   No    802.11b   1
xx:xx:xx:xx:xx:xx  AP02               Probing        N/A   No    802.11b   1
xx:xx:xx:xx:xx:xx  AP02               Probing        N/A   No    802.11a   1
xx:xx:xx:xx:xx:xx  AP02               Probing        N/A   No    802.11a   1
xx:xx:xx:xx:xx:xx  AP02               Probing        N/A   No    802.11b   1
xx:xx:xx:xx:xx:xx  AP02               Probing        N/A   No    802.11a   1
xx:xx:xx:xx:xx:xx  AP02               Probing        N/A   No    802.11a   1
Related CommandsNumber of Clients................................ 2

Related Commands

Related CommandsMAC Address AP Name Status WLAN Auth Protocol Port

Related Commands----------------- ----------------- ------------- ---- ---- -------- ----

Related Commands

Related Commands00:13:02:1e:9b:c6 ap:0e:19:a0 Probing N/A No 802.11a 1

Related Commands00:14:6c:0a:57:77 ap:0e:19:a0 Diagnostics 1 Yes 802.11a 1

Related Commands

Command

Description

TBD

TBD

TBD

show client username

To display client data by username, use the show client username command.

show client username username
Syntax Description

show

Display configurations.

client

Display client data.

username

Cisco radio.

username

Client's username.

Defaults

None.

Examples
> show client username IT_007
MAC Address        AP ID   Status         WLAN Id    Authenticated
-----------------  ------  -------------  ---------  -------------
xx:xx:xx:xx:xx:xx  1       Associated     1          No
Related Commands

show client ap, show client detail, show client summary

show country

To display the configured country and the radio types supported, use the show country channels command.

show country
This command has no arguments or keywords.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show country
Configured Country............................. United States
Configured Country Codes
US  - United States............................. 802.11a / 802.11b / 802.11g
Related Commands

Command

Description

config country

Configures the controller's regulatory country of operation.

display country supported

Displays a list of the supported country options.

show country channels

Displays the radio channels supported in the configured country.

show country channels

To display the radio channels supported in the configured country, use the show country channels command.

show country channels
Syntax Description

This command has no arguments or keywords.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show country channels
Configured Country............................. United States
      KEY: * = Channel is legal in this country and may be configured manually.
           A = Channel is the Auto-RF default in this country.
           . = Channel is not legal in this country.
           C = Channel has been configured for use by Auto-RF.
           x = Channel is available to be configured for use by Auto-RF.
---------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11BG :
Channels :                   1 1 1 1 1
         : 1 2 3 4 5 6 7 8 9 0 1 2 3 4
---------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
     US  : A * * * * A * * * * A . . .
---------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
 802.11A :                         1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Channels : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6
         : 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5
---------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
     US  : . A . A . A . A A A A A * * * * * . . . * * * A A A A *
---------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
Related Commands

Command

Description

config country

Configures the controller's regulatory country of operation.

display country supported

Displays a list of the supported country options.

show country

Displays the configured country and the radio types supported.

show country supported

To display a list of the supported country options, use the show country supported command.

show country supported
Syntax Description

This command has no arguments or keywords.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show country supported
CConfigured Country............................. United States
Supported Country Codes
AR  - Argentina................................. 802.11a / 802.11b / 802.11g
AT  - Austria................................... 802.11a / 802.11b / 802.11g
AU  - Australia................................. 802.11a / 802.11b / 802.11g
BR  - Brazil.................................... 802.11a / 802.11b / 802.11g
BE  - Belgium................................... 802.11a / 802.11b / 802.11g
BG  - Bulgaria.................................. 802.11a / 802.11b / 802.11g
CA  - Canada.................................... 802.11a / 802.11b / 802.11g
CH  - Switzerland............................... 802.11a / 802.11b / 802.11g
CL  - Chile.....................................           802.11b / 802.11g
CN  - China..................................... 802.11a / 802.11b / 802.11g
CO  - Colombia..................................           802.11b / 802.11g
CY  - Cyprus.................................... 802.11a / 802.11b / 802.11g
CZ  - Czech Republic............................ 802.11a / 802.11b
DE  - Germany................................... 802.11a / 802.11b / 802.11g
DK  - Denmark................................... 802.11a / 802.11b / 802.11g
EE  - Estonia................................... 802.11a / 802.11b / 802.11g
ES  - Spain..................................... 802.11a / 802.11b / 802.11g
FI  - Finland................................... 802.11a / 802.11b / 802.11g
FR  - France.................................... 802.11a / 802.11b / 802.11g
GB  - United Kingdom............................ 802.11a / 802.11b / 802.11g
GI  - Gibraltar................................. 802.11a / 802.11b / 802.11g
GR  - Greece.................................... 802.11a / 802.11b / 802.11g
HK  - Hong Kong................................. 802.11a / 802.11b / 802.11g
HU  - Hungary................................... 802.11a / 802.11b / 802.11g
ID  - Indonesia.................................           802.11b / 802.11g
IE  - Ireland................................... 802.11a / 802.11b / 802.11g
IN  - India..................................... 802.11a / 802.11b / 802.11g
IL  - Israel.................................... 802.11a / 802.11b / 802.11g
ILO - Israel (outdoor)..........................           802.11b / 802.11g
IS  - Iceland................................... 802.11a / 802.11b / 802.11g
IT  - Italy..................................... 802.11a / 802.11b / 802.11g
JP  - Japan (J)................................. 802.11a / 802.11b / 802.11g
J2  - Japan 2(P)................................ 802.11a / 802.11b / 802.11g
J3  - Japan 3(U)................................ 802.11a / 802.11b / 802.11g
KR  - Korea Republic (C)........................ 802.11a / 802.11b / 802.11g
KE  - Korea Extended (K)........................ 802.11a / 802.11b / 802.11g
LI  - Liechtenstein............................. 802.11a / 802.11b / 802.11g
LT  - Lithuania................................. 802.11a / 802.11b / 802.11g
LU  - Luxembourg................................ 802.11a / 802.11b / 802.11g
LV  - Latvia.................................... 802.11a / 802.11b / 802.11g
MC  - Monaco.................................... 802.11a / 802.11b / 802.11g
MT  - Malta..................................... 802.11a / 802.11b / 802.11g
MX  - Mexico.................................... 802.11a / 802.11b / 802.11g
MY  - Malaysia.................................. 802.11a / 802.11b / 802.11g
NL  - Netherlands............................... 802.11a / 802.11b / 802.11g
NZ  - New Zealand............................... 802.11a / 802.11b / 802.11g
NO  - Norway.................................... 802.11a / 802.11b / 802.11g
PA  - Panama....................................           802.11b / 802.11g
PE  - Peru......................................           802.11b / 802.11g
PH  - Philippines............................... 802.11a / 802.11b / 802.11g
PL  - Poland.................................... 802.11a / 802.11b / 802.11g
PT  - Portugal.................................. 802.11a / 802.11b / 802.11g
RU  - Russian Federation........................ 802.11a / 802.11b / 802.11g
RO  - Romania................................... 802.11a / 802.11b / 802.11g
SA  - Saudi Arabia.............................. 802.11a / 802.11b / 802.11g
SE  - Sweden.................................... 802.11a / 802.11b / 802.11g
SG  - Singapore................................. 802.11a / 802.11b / 802.11g
SI  - Slovenia.................................. 802.11a / 802.11b / 802.11g
SK  - Slovak Republic........................... 802.11a / 802.11b / 802.11g
TH  - Thailand..................................           802.11b / 802.11g
TR  - Turkey....................................           802.11b / 802.11g
TW  - Taiwan.................................... 802.11a / 802.11b / 802.11g
UA  - Ukraine................................... 802.11a / 802.11b / 802.11g
US  - United States............................. 802.11a / 802.11b / 802.11g
USL - United States (Legacy).................... 802.11a / 802.11b / 802.11g
USX - United States (US + chan165).............. 802.11a / 802.11b / 802.11g
VE  - Venezuela.................................           802.11b / 802.11g
ZA  - South Africa.............................. 802.11a / 802.11b / 802.11g
Related Commands

Command

Description

config country

Configures the controller's regulatory country of operation.

display country channels

Displays a list of the supported channels used by Auto-RF.

show country

Displays the configured country and the radio types supported.

show cpu

To display current WLAN Controller CPU usage information, use the show cpu command.

show cpu
Syntax Description

show cpu

Command action.

Defaults

None.

Examples
> show cpu
Current CPU load: 2.50%
Related Commands

show sysinfo

show custom-web

To display web authentication customization information, use the show custom-web command.

show custom-web
Syntax Description

show custom-web

Command action.

Defaults

None.

Examples
> show custom-web
Radius Authentication Method..................... PAP
Cisco Logo....................................... Enabled
CustomLogo....................................... None
Custom Title..................................... None
Custom Message................................... None
Custom Redirect URL.............................. None
External web authentication Mode................. Disabled
External web authentication URL.................. None
Related Commands

config custom-web

show database summary

To display the maximum number of entries in the database, use the show database summary command.

show database summary
Syntax Description

This command has no arguments or keywords.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show database summary
Current Max database entries..................... 512
Max database entries on next reboot.............. 512
Related Commands

Command

Description

config database size

Configures the maximum number of entries in the database.

show debug

Use the show debug command, to determine if MAC address and other flag debugging is enabled or disabled.

show debug
Syntax Description

show

Display configurations.

debug

MAC address debugging.

Defaults

disabled.

Examples
> show debug
MAC debugging............................... disabled
Debug Flags Enabled:
  arp error enabled.
  bcast error enabled.
Related Commands

debug mac

show dhcp

Use the show dhcp command, to display the internal DHCP server configuration.

show dhcp {leases | summary | scope}
Syntax Description

show dhcp

Display internal DHCP server configuration information.

leases

Enter leases to display allocated DHCP leases.

summary

Enter summary to display DHCP summary information.

scope

Enter the name of a scope to display the DHCP information for that scope.

Defaults

None.

Examples
> show dhcp leases
No leases allocated.
> show dhcp summary
Scope Name           Enabled           Address Range
003                    No            0.0.0.0 -> 0.0.0.0
> show dhcp 003
Enabled....................................... No
Lease Time.................................... 0
Pool Start.................................... 0.0.0.0
Pool End...................................... 0.0.0.0
Network....................................... 0.0.0.0
Netmask....................................... 0.0.0.0
Default Routers............................... 0.0.0.0 0.0.0.0 0.0.0.0
DNS Domain.................................... 
DNS........................................... 0.0.0.0 0.0.0.0 0.0.0.0
Netbios Name Servers.......................... 0.0.0.0 0.0.0.0 0.0.0.0
Related Commands

config dhcp

show dhcp proxy

Use the show dhcp proxy command to display the status of DHCP proxy handling.

show dhcp proxy
Syntax Description

show dhcp proxy

Display the status of DHCP proxy handling.

Defaults

None.

Examples
> show dhcp proxy 
DHCP Proxy Behaviour: enabled

Related Commands

config dhcp proxy

show eventlog

Use the show eventlog command, to display the event log.

show eventlog
Syntax Description

show

Display configurations.

eventlog

System events.

Defaults

None.

Examples
> show eventlog
                                             Time
       File     Line TaskID   Code        d  h  m  s
EVENT> bootos.c  788 125CEBCC AAAAAAAA    0  0  0  6
EVENT> bootos.c  788 125CEBCC AAAAAAAA    0  0  0  6
EVENT> bootos.c  788 125C597C AAAAAAAA    0  0  0  6
EVENT> bootos.c  788 125C597C AAAAAAAA    0  0  0  6
EVENT> bootos.c  788 125C597C AAAAAAAA    0  0  0  6
EVENT> bootos.c  788 125C597C AAAAAAAA    0  0  0  6
EVENT> bootos.c  788 125C597C AAAAAAAA    0  0  0  6
EVENT> bootos.c  788 125C597C AAAAAAAA    0  0  0  6
EVENT> bootos.c  788 1216C36C AAAAAAAA    0  0  0  6
EVENT> bootos.c  788 1216C36C AAAAAAAA    0  0  0  6
EVENT> bootos.c  788 1216C36C AAAAAAAA    0  0  0  6
EVENT> bootos.c  788 1216C36C AAAAAAAA    0  0  0 11
Related Commands

show msglog

show exclusionlist

To display a summary of all clients on the manual exclusion list (blacklisted) from associating with this Cisco Wireless LAN controller, use the show exclusionlist command. A list containing each manually Excluded MAC address is displayed.

show exclusionlist
Syntax Description

show

Display configurations.

exclusionist

Manual exclusion list.

Defaults

None.

Examples
> show exclusionlist
MAC Address              Description
-----------------------  --------------------------------
xx:xx:xx:xx:xx:xx        Disallowed Client
Related Commands

config exclusionlist add, config exclusionlist delete, config exclusionlist description, show client

show ike

Use the show ike command to display active IKE SAs.

show ike {brief | IP_or_MAC_address}
Syntax Description

show

Command action.

ike

Display active IKE SAs.

brief

List of all active IKE SAs.

IP_or_MAC_address

IP or MAC address of active IKE SA.

Defaults

None.

Examples
> show ike
Related Commands

None

show interface

Use the show interface command to display details of the system interfaces.

show interface {summary | detailed interface_name}
Syntax Description

show interface

Command action

summary

Display a summary of the local interfaces.

detailed

Display detailed interface information.

interface_name

Identifies interface name for detailed display

Defaults

None.

Examples
> show interface summary
Interface Name                    Vlan Id   IP Address       Type     Ap Mgr
--------------------------------  --------  ---------------  -------  ------
ap-manager                        149       xxx.xxx.xxx.xxx  Static   Yes
management                        149       xxx.xxx.xxx.xxx  Static   No
service-port                      N/A       xxx.xxx.xxx.xxx  Static   No
virtual                           N/A       xxx.xxx.xxx.xxx  Static   No
> show interface detailed management
Interface Name................................... management
MAC Address...................................... 00:0b:85:32:ab:60
IP Address....................................... 1.100.49.30
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 1.100.49.1
VLAN............................................. 149
Active Physical Port............................. 1
Primary Physical Port............................ 1
Backup Physical Port............................. Unconfigured
Primary DHCP Server.............................. 1.100.2.15
Secondary DHCP Server............................ Unconfigured
ACL.............................................. Unconfigured
AP Manager....................................... No
Note Some WLAN controllers may have only one physical port listed because they have only one physical port.

Related Commands

config interface

show inventory

To display a physical inventory of the Cisco Wireless LAN controller, use the show inventory command.

show inventory
Syntax Description

show

Display configurations.

inventory

Physical Cisco Wireless LAN controller configuration.

Defaults

None.

Examples
> show inventory
Switch Description............................... Cisco Controller
Machine Model.................................... WLC4404-100
Serial Number.................................... FLS0923003B
Burned-in MAC Address............................ 00:0B:85:32:AB:60
Crypto Accelerator 1............................. Absent
Crypto Accelerator 2............................. Absent
Power Supply 1................................... Absent
Power Supply 2................................... Present, OK
Note Some wireless LAN controllers may have no crypto accelerator (VPN termination module) or power supplies listed because they have no provisions for VPN termination modules or power supplies.

Related Commands

show sysinfo

show ipsec

Use the show ipsec command to display active IPSec SAs.

show ipsec {brief | IP_or_MAC_address}
Syntax Description

show

Command action.

ipsec

Display active IPSec SAs

{brief |
IP_or_MAC_address}

Enter brief to display active IPSec SAs.

Enter the IP address of MAC address of an IPSec SA.

Defaults

None.

Examples
> show ipsec brief
Related Commands

None

show known ap

To display known Cisco 1000 series lightweight access point information, use the show known ap command.

show known ap {summary | detailed MAC}
Syntax Description

show

Display configurations.

known ap

Known Cisco 1000 series lightweight access point information.

summary

Displays a list of all known access points.

detailed

Provides detailed information for all known access points.

MAC

MAC address of the known AP

Defaults

None.

Examples
> show known ap summary
MAC Address         State        # APs  # Clients   Last Heard
-----------         -----------  -----   --------   -----------------
Related Commands

config ap

show l2tp

To display L2TP sessions, use the show l2tp command.

show l2tp {summary | ip_address}
Syntax Description

show l2tp

Display configurations.

summary

Displays all L2TP sessions.

ip_address

Displays an L2TP session.

Defaults

None.

Examples
> show l2tp summary
LAC_IPaddr LTid LSid RTid RSid ATid ASid State
---------- ---- ---- ---- ---- ---- ---- -----
Related Commands

None

show lag summary

To display the current LAG status, use the show lag summary command.

show lag summary
Syntax Description

This command has no arguments or keywords.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show lag summary
LAG Enabled
Related Commands

Command

Description

config lag

Enables or disables LAG settings.

show ldap summary

To display the current LDAP status, use the show ldap summary command.

show ldap summary
Syntax Description

This command has no arguments or keywords.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show ldap summary
Idx
Server Address
Port
Enabled
----
--------------
----
--------
10
10.31.15.45
2
Yes
Related Commands

Command

Description

config ldap

Configures LDAP server settings.

show load-balancing

To display the status of the load-balancing feature, use the show load-balancing command.

show load-balancing
Syntax Description

show

Display configurations.

load-balancing

Display the load-balancing status.

Defaults

None.

Examples
> show load-balancing
Aggressive Load Balancing...................... Enabled
Aggressive Load Balancing Window............... 0 clients
Related Commands

config load-balancing

show local-auth certificates

This command is used display local authentication certificate information:

show local-auth certificates
Syntax Description

This command has no arguments or keywords.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show local-auth certificates 
Certificates available for Local EAP authentication: 
 
Certificate issuer .............................. vendor
CA certificate:
Subject: C=AU, ST=NSW, L=Sydney, O=Cisco Systems 
OU=WNBU Sydney, CN=wnbu-syd-acs-a.cisco.com 
Issuer: C=AU, ST=NSW, L=Sydney, O=Cisco Systems 
OU=WNBU Sydney, CN=wnbu-syd-acs-a.cisco.com 
Valid: 2005 Jun 15th, 04:53:49 GMT to 2008 Jun 15th, 05:03:34 GMT 
Device certificate: 
Subject: MAILTO=test@test.net, C=AU, ST=NSW, L=Sydney 
O=Cisco Systems, OU=WNBU Sydney, CN=concannon 
Issuer: C=AU, ST=NSW, L=Sydney, O=Cisco Systems 
OU=WNBU Sydney, CN=wnbu-syd-acs-a.cisco.com 
Valid: 2006 Aug 9th, 05:14:16 GMT to 2007 Aug 9th, 05:24:16 GMT
Certificate issuer .............................. cisco
CA certificate:
Subject: C=US, ST=California, L=San Jose, O=airespace Inc 
OU=none, CN=ca, MAILTO=support@airespace.com 
Issuer: C=US, ST=California, L=San Jose, O=airespace Inc 
OU=none, CN=ca, MAILTO=support@airespace.com 
Valid: 2003 Feb 12th, 23:38:55 GMT to 2012 Nov 11th, 23:38:55 GMT 
Device certificate: 
Subject: C=US, ST=California, L=San Jose, O=airespace Inc 
CN=000b85335340, MAILTO=support@airespace.com 
Issuer: C=US, ST=California, L=San Jose, O=airespace Inc 
OU=none, CN=ca, MAILTO=support@airespace.com 
Valid: 2005 Feb 22nd, 10:52:58 GMT to 2014 Nov 22nd, 10:52:58 GMT
Certificate issuer .............................. legacy
CA certificate:
Subject: C=US, ST=California, L=San Jose, O=airespace Inc 
OU=none, CN=ca, MAILTO=support@airespace.com 
Issuer: C=US, ST=California, L=San Jose, O=airespace Inc 
OU=none, CN=ca, MAILTO=support@airespace.com 
Valid: 2003 Feb 12th, 23:38:55 GMT to 2012 Nov 11th, 23:38:55 GMT 
 
Device certificate: 
Subject: C=US, ST=California, L=San Jose, O=airespace Inc 
CN=000b85335340, MAILTO=support@airespace.com 
Issuer: C=US, ST=California, L=San Jose, O=airespace Inc 
OU=none, CN=ca, MAILTO=support@airespace.com 
Valid: 2005 Feb 22nd, 10:52:58 GMT to 2014 Nov 22nd, 10:52:58 GMT
Related Commands

Command

Description

TBD

TBD

TBD

show local-auth config

This command is used display local authentication configuration information:

show local-auth config
Syntax Description

This command has no arguments or keywords.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show local-auth config
User credentials database search order:
Primary ................................... Local DB
Configured EAP profiles:
Name ...................................... fast-test
Certificate issuer .................... default
Enabled methods ....................... fast
Configured on WLANs ................... 2
EAP Method configuration:
EAP-TLS:
Certificate issuer .................... default
Peer verification options:
	Check against CA certificates ..... Enabled
	Verify certificate CN identity .... Disabled
	Check certificate date validity ... Enabled
EAP-FAST:
TTL for the PAC ....................... 3 600
Initial client message ................ <none>
Local certificate required ............ No
Client certificate required ........... No
Vendor certificate required ........... No
Anonymous provision allowed ........... Yes
Authenticator ID ...................... 7b7fffffff0000000000000000000000
Authority Information ................. Test
EAP Profile.................................... tls-prof
Enabled methods for this profile .......... tls
Active on WLANs ........................... 1 3
EAP Method configuration:
EAP-TLS:
Certificate issuer used ............... cisco
Peer verification options:
	Check against CA certificates ..... disabled
	Verify certificate CN identity .... disabled
	Check certificate date validity ... disabled
Related Commands

Command

Description

config local-auth fast

Configures a certificate issuer to use EAP-FAST authentication.

config local-auth method tls

Configures a certificate issuer to use EAP-TLS authentication.

show local-auth statistics - TBD Need Info

This command is used display local EAP authentication statistics:

show local-auth statistics
Syntax Description

This command has no arguments or keywords.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show local-auth stat
Local EAP authentication DB statistics:
Requests received .................................. 14
Responses returned ................................. 14
Requests dropped (no EAP AVP) ...................... 0
Requests dropped (other) ........................... 0
Authentication responses returned:
Success ........................................ 1
Failed ......................................... 1
Local EAP backend request statistics:
Requests sent to LDAP DB ........................... 0
Requests sent to File DB ........................... 2
Requests failed .................................... 0
Authentication responses received:
Success ........................................ 2
Fail ........................................... 0
Related Commands

Command

Description

show local-auth registrations

This command is used display the local EAP method and the lower layer registrations:

show local-auth registrations
Syntax Description

This command has no arguments or keywords.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
# show local-auth registrations
Registered EAP Methods:
Method
Type
Name
4
Auth and Peer
MD5
6
Auth and Peer
GTC
13
Auth and Peer
TLS
17
Auth and Peer
LEAP
26
Auth and Peer
MSCHAPV2
43
Auth and Peer
EAP-FAST
Registered EAP Lower Layers
Handle
Type
Name
2
Authenticator
LOCAL_EAP_DB
1
Auth and Peer
EAP-FAST
Related Commands

Command

Description

show local-auth statistics

This command is used display local EAP authentication statistics:

show local-auth statistics
Syntax Description

This command has no arguments or keywords.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show local-auth stat
Local EAP authentication DB statistics:
Requests received .................................. 14
Responses returned ................................. 14
Requests dropped (no EAP AVP) ...................... 0
Requests dropped (other) ........................... 0
Authentication responses returned:
Success ........................................ 1
Failed ......................................... 1
Local EAP backend request statistics:
Requests sent to LDAP DB ........................... 0
Requests sent to File DB ........................... 2
Requests failed .................................... 0
Authentication responses received:
Success ........................................ 2
Fail ........................................... 0
Related Commands

Command

Description

show location summary

To display information about defined locations, use the show location summary command.

show location summary
Syntax Description

show location

Display command for locations.

summary

Display all location information defined in the system.

Defaults

None.

Examples
> show location summary
Status...................................................... disabled
Related Commands

config location

show loginsession

To display the existing sessions, use the show loginsession command.

show loginsession
Syntax Description

show

Display configurations.

loginsession

Current session details.

Defaults

None.

Examples
> show loginsession
ID    User Name     Connection From   Idle Time    Session Time
-- ---------------  ---------------  ------------  ------------
00 admin            EIA-232          00:00:00      00:19:04
Related Commands

config loginsession close

show macfilter

To display the MAC filter parameters, use the show macfilter command. The MAC delimiter (none, colon, or hyphen) for MAC addresses sent to RADIUS servers is displayed. The MAC filter table lists the clients that are always allowed to associate with a wireless LAN.

show macfilter {summary | detail MAC}
Syntax Description

show

Display configurations.

macfilter

Filter details.

summary

Display a summary of all MAC filter entries.

detail MAC

Detailed display of a MAC filter entry.

Defaults

None.

Examples
> show macfilter detail xx:xx:xx:xx:xx:xx
MAC Address...................................... xx:xx:xx:xx:xx:xx
WLAN Identifier.................................. Any
Interface Name................................... management
Description...................................... RAP
> show macfilter summary
MAC Filter RADIUS Compatibility mode............. Cisco ACS
MAC Filter Delimiter............................. None
Local Mac Filter Table
MAC Address               WLAN Id          Description
-----------------------   --------------   --------------------------------
xx:xx:xx:xx:xx:xx         Any              RAP
xx:xx:xx:xx:xx:xx         Any              PAP2 (2nd hop)
xx:xx:xx:xx:xx:xx         Any              PAP1 (1st hop)
Related Commands

config macfilter mac-delimiter, config macfilter add, config macfilter delete, config macfilter description, config macfilter ip-address, config macfilter wlan-id

SHOW MESH COMMANDS

Use the SHOW MESH commands to display mesh settings.

show mesh cac bwused

To display the mesh CAC topology and the bandwidth used or available, use the show mesh cac bwused command.

show mesh cac bwused [voice | video ] ap_name
Syntax Description

voice

Displays the mesh topology and the voice bandwidth used or available.

video

Displays the mesh topology and the video bandwidth used or available.

ap_name

Specifies the mesh access point name.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show mesh cac bwused voice ap1510-9119c0
AP Name

Model

Radio

Bw used/max

Radio

Bw used/max

--------------

-------

------

-------------

-------

--------------

AP1510-9119c0

LAP1510

11a

2032/12500

11b/g

2728/12500
Related Commands

Command

Description

TBD

TBD

TBD

show mesh cac calls

To display the mesh CAC topology and the calls inprogress, use the show mesh cac calls command.

show mesh cac calls ap_name
Syntax Description

ap_name

Specifies the mesh access point name.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> debug mesh cac calls
Related Commands

Command

Description

TBD

TBD

TBD

show mesh client-access

To display the backhaul client access configuration setting, use the show mesh client-access command.

show mesh client-access
Syntax Description

This command has no arguments or keywords.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show mesh client-access
Backhaul with client access status: enabled
Related Commands

Command

Description

config mesh client-access

TBD

show mesh env summary

To display summary information on the mesh environment, use the show mesh env summary command.

show mesh env summary
Syntax Description

This command has no arguments or keywords.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show mesh env summary
AP Name             Temperature(C)  Heater   Ethernet  Battery
------------------  --------------  ------   --------  -------
ap1020:5f:be:90      N/A             N/A      DOWN     N/A
AP1242:b2.31.ea      N/A             N/A      DOWN     N/A
AP1131:f2.8d.92      N/A             N/A      DOWN     N/A
AP1131:46f2.98ac     N/A             N/A      DOWN     N/A
ap1500:62:39:70      -36             OFF      UP       N/A
Related Commands

Command

Description

show mesh neigh summary

Displays summary information on the mesh neighbors.

show mesh linkrate

To display the mesh link rate for Cisco 1000 series lightweight access points, use the show mesh linkrate command.

show mesh linkrate <from Cisco_AP> <to Cisco_AP name|MAC address>
Syntax Description

show

Display configurations.

mesh

Mesh configuration.

linkrate

Show link rate statistics

from Cisco_AP

From Cisco 1000 series lightweight access point name.

to Cisco_AP name|MAC address

To Cisco 1000 series lightweight access point name or MAC address.

Defaults

None.

Examples
> show mesh linkrate
Related Commands

None.

show mesh neigh

To display the mesh neighbors for a Cisco 1000 series lightweight access point, use the show mesh neigh command.

show mesh neigh Cisco_AP
Syntax Description

show

Display configurations.

mesh

Mesh configuration.

neigh

Show Cisco 1000 series lightweight access point neighborhood list.

Cisco_AP

Cisco 1000 series lightweight access point name.

Defaults

None.

Examples
> show mesh neigh
Related Commands

None.

show mesh neigh summary

This command is used display mesh access point neighbor summary information ---TBD.

show mesh neigh [ detail | summary ] ap_name ]
Syntax Description

detail

Displays

summary

Displays mesh neighbor summary information for all the access points.

ap_name

Displays the mesh neighbors for the specified access point.

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show mesh neighbor summary ap1500:62:39:70
AP MAC : 00:0B:85:5F:FB:30
FLAGS : 860 BEACON
worstDv 255, Ant 0, channel 161, biters 0, ppiters 0
Numroutes 0, snr 0, snrUp 0, snrDown 0, linkSnr 0
adjustedEase 0, unadjustedEase 0
txParent 0, rxParent 0
poorSnr  0
lastUpdate   1162403569 (Wed Nov  1 17:52:49 2006)
parentChange 0
Per antenna smoothed snr values: 0 0 0 0
Vector through 00:0B:85:5F:FB:30
AP MAC : 00:0B:85:64:01:B0
FLAGS : 160 CHILD
worstDv 255, Ant 0, channel 161, biters 0, ppiters 10
Numroutes 0, snr 0, snrUp 0, snrDown 37, linkSnr 0
adjustedEase 0, unadjustedEase 0
txParent 0, rxParent 0
poorSnr  0
lastUpdate   1162410596 (Wed Nov  1 19:49:56 2006)
parentChange 0
Per antenna smoothed snr values: 0 0 0 0
Vector through 00:0B:85:64:01:B0
> show mesh neigh detail ap1500:62:39:70
AP MAC : 00:0B:85:5F:FB:30
FLAGS : 860 BEACON
worstDv 255, Ant 0, channel 161, biters 0, ppiters 0
Numroutes 0, snr 0, snrUp 0, snrDown 0, linkSnr 0
adjustedEase 0, unadjustedEase 0
txParent 0, rxParent 0
poorSnr  0
lastUpdate   1162403569 (Wed Nov  1 17:52:49 2006)
parentChange 0
Per antenna smoothed snr values: 0 0 0 0
Vector through 00:0B:85:5F:FB:30
AP MAC : 00:0B:85:64:01:B0
FLAGS : 160 CHILD
worstDv 255, Ant 0, channel 161, biters 0, ppiters 10
Numroutes 0, snr 0, snrUp 0, snrDown 36, linkSnr 0
adjustedEase 0, unadjustedEase 0
txParent 0, rxParent 0
poorSnr  0
lastUpdate   1162410929 (Wed Nov  1 19:55:29 2006)
parentChange 0
Per antenna smoothed snr values: 0 0 0 0
Vector through 00:0B:85:64:01:B0
Related Commands

Command

Description

config mesh mac-filter

Configures bridge MAC filter mode.

show mesh env

Displays the mesh environment

show mesh path

To display the mesh configuration for a Cisco 1000 series lightweight access point, use the show mesh path command.

show mesh path Cisco_AP
Syntax Description

show

Display configurations.

mesh

Mesh configuration.

path

Show Cisco 1000 series lightweight access point path.

Cisco_AP

Cisco 1000 series lightweight access point name.

Defaults

None.

Examples
> show mesh path
Related Commands

None.

show mesh range

This command displays the current mesh range configuration settings:

show mesh range
Syntax Description

This command has no arguments or keywords

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show mesh range
MESH Range: 12000
Related Commands

Command

Description

config mesh range

Configures maximum mesh operating range.

show mesh secondary-backhaul

This command displays the current mesh secondary backhaul configuration settings:

show mesh secondary-backhaul
Syntax Description

This command has no arguments or keywords

Defaults

This command has no defaults.

Command History

Release

Modification

4.1

This command was first introduced.

Examples
> show mesh secondary-backhaul
MESH secondary-backhaul: enabled
Related Commands

Command

Description

config mesh secondary-backhaul

Configures mesh secondary backhaul capability.

show mesh stats

To display the mesh statistics for a Cisco 1000 series lightweight access point, use the show mesh stats command.

show mesh stats Cisco_AP
Syntax Description

show

Display configurations.

mesh

Mesh configuration.

stats

Show Cisco 1000 series lightweight access point statistics.

Cisco_AP

Cisco 1000 series lightweight access point name.

Defaults

None.

Examples
> show mesh stats
Related Commands

None.

show mesh summary

To display the mesh configuration for a Cisco 1000 series lightweight access pointr, use the show mesh summary command.

show mesh summary Cisco_AP
Syntax Description