Table Of Contents

Cisco Aironet 1130 Series Access Points

Channels and Maximum Power Levels

IEEE 802.11b/g (2.4-GHz Band)

IEEE 802.11b/g (2.4-GHz Band)

IEEE 802.11a (5-GHz Band)

Special Country Restrictions

Changing Access Point Output Power

Cisco Aironet 1130 Series Access Points

---

This chapter lists the 1130 series autonomous access point (models: AIR-AP1131AG-x-K9 and AIR-AP1131G-x-K9) IEEE 802.11b/g (2.4-GHz) and the IEEE 802.11a (5-GHz) channels and maximum power levels supported by the world's regulatory domains. For additional product hardware information refer to the Cisco Aironet 1130AG Series Access Point Hardware Installation Guide.

The following topics are covered in this chapter:

•Channels and Maximum Power Levels

•Special Country Restrictions

•Changing Access Point Output Power

Channels and Maximum Power Levels

IEEE 802.11b/g (2.4-GHz Band)

When shipped from the factory, the AIR-AP1131G-x-K9 (single radio) access points support the channels and maximum power levels listed in Table 2-1 for their regulatory domain.

---

Note The B columns indicate IEEE 802.11b data rates and the G columns indicate IEEE 802.11g data rates.

---

.

Table 2-1 Channels and Maximum Conducted Power for the 802.11g Radio `
with 3-dBi Integrated Antenna 

Channel Id	Center Freq (MHz)	Maximum Conducted Power Levels (dBm) in the Regulatory Domains
		-A		-E		-P
		B	G	B	G	B	G
1	2412	20	17	14	14	14	14
2	2417	20	17	14	14	14	14
3	2422	20	17	14	14	14	14
4	2427	20	17	14	14	14	14
5	2432	20	17	14	14	14	14
6	2437	20	17	14	14	14	14
7	2442	20	17	14	14	14	14
8	2447	20	17	14	14	14	14
9	2452	20	17	14	14	14	14
10	2457	20	17	14	14	14	14
11	2462	20	17	14	14	14	14
12	2467	-	-	14	14	14	14
13	2472	-	-	14	14	14	14
14	2484	-	-	-	-	14	-

IEEE 802.11b/g (2.4-GHz Band)

When shipped from the factory, the AIR-AP1131AG-x-K9 (dual radio) access points support the channels and maximum power levels listed in Table 2-2 for their regulatory domain.

---

Note The B columns indicate IEEE 802.11b data rates and the G columns indicate IEEE 802.11g data rates.

---

.

Table 2-2 Channels and Maximum Conducted Power for the 802.11b/g Radio with 3-dBi Integrated Antenna 

Channel Id	Center Freq (MHz)	Maximum Conducted Power Levels (dBm) in the Regulatory Domains
		-A		-C		-E		-I		-J		-K		-N		-P		-Q		-S		-T
		B	G	B	G	B	G	B	G	B	G	B	G	B	G	B	G	B	G	B	G	B	G
1	2412	20	17	14	14	14	14	14	14	14	14	14	14	20	17	14	14	14	14	14	14	20	17
2	2417	20	17	14	14	14	14	14	14	14	14	14	14	20	17	14	14	14	14	14	14	20	17
3	2422	20	17	14	14	14	14	14	14	14	14	14	14	20	17	14	14	14	14	14	14	20	17
4	2427	20	17	14	14	14	14	14	14	14	14	14	14	20	17	14	14	14	14	14	14	20	17
5	2432	20	17	14	14	14	14	14	14	14	14	14	14	20	17	14	14	14	14	14	14	20	17
6	2437	20	17	14	14	14	14	14	14	14	14	14	14	20	17	14	14	14	14	14	14	20	17
7	2442	20	17	14	14	14	14	14	14	14	14	14	14	20	17	14	14	14	14	14	14	20	17
8	2447	20	17	14	14	14	14	14	14	14	14	14	14	20	17	14	14	14	14	14	14	20	17
9	2452	20	17	14	14	14	14	14	14	14	14	14	14	20	17	14	14	14	14	14	14	20	17
10	2457	20	17	14	14	14	14	14	14	14	14	14	14	20	17	14	14	14	14	14	14	20	17
11	2462	20	17	14	14	14	14	14	14	14	14	14	14	20	17	14	14	14	14	14	14	20	17
12	2467	-	-	14	14	14	14	14	14	14	14	14	14	-	-	14	14	14	14	14	14	-	-
13	2472	-	-	14	14	14	14	14	14	14	14	14	14	-	-	14	14	14	14	14	14	-	-
14	2484	-	-	-	-	-	-	-	-	14	-	-	-	-	-	14	-	14	-	-	-	-	-

IEEE 802.11a (5-GHz Band)

When shipped from the factory, the AIR-AP1131AG-x-K9 (dual radio) access points support the channels and maximum power levels listed in Table 2-3 for their regulatory domain.

---

Note Access points with FCC Certification Number (LDK102054) do not support dynamic frequency selection (DFS) on channels 52 to 64 and 100 to 140 in the US and Canada. The FCC Certification Number (also called FCC ID number) is shown on the product label on the bottom of the unit. Only access points with LDK102054E on the product label can support DFS in the US and Canada.

---

.

Table 2-3 Channels and Maximum Conducted Power for IEEE 802.11a Radio with 3-dBI Integrated Antenna 

Channel ID	Center Freq (MHz)	Maximum Conducted Power Levels (dBm) in the Regulatory Domains
		-A	-C	-E	-I	-J	-K	-N	-P	-Q	-U	-S	-T
5150 to 5250 MHz
34	5170	-	-	-	-	15	-	-	-	-	-	-	-
36	5180	15	-	17	17	-	15	15	15	15	15	17	-
38	5190	-	-	-	-	15	-	-	-	-	-	-	-
40	5200	15	-	17	17	-	15	15	15	15	15	17	-
42	5210	-	-	-	-	15	-	-	-	-	-	-	-
44	5220	15	-	17	17	-	15	15	15	15	15	17	-
46	5230	-	-	-	-	15	-	-	-	-	-	-	-
48	5240	15	-	17	17	-	15	15	15	15	15	17	-
5250 to 5350 MHz
52	5260	17	-	171	171	-	171	171	151	151	-	141	-
56	5280	17	-	171	171	-	171	171	151	151	-	141	15
60	5300	17	-	171	171	-	171	171	151	151	-	141	15
64	5320	17	-	171	171	-	171	171	151	151	-	141	15
5450 to 5725 MHz
100	5500	171	-	171	-	-	171	-	-	171	-	-	171
104	5520	171	-	171	-	-	171	-	-	171	-	-	171
108	5540	171	-	171	-	-	171	-	-	171	-	-	171
112	5560	171	-	171	-	-	171	-	-	171	-	-	171
116	5580	171	-	171	-	-	171	-	-	171	-	-	171
120	5600	-	-	171	-	-	171	-	-	171	-	-	171
124	5620	-	-	171	-	-	171	-	-	171	-	-	171
128	5640	-	-	171	-	-	-	-	-	171	-	-	171
132	5660	171	-	171	-	-	-	-	-	171	-	-	171
136	5680	171	-	171	-	-	-	-	-	171	-	-	171
140	5700	171	-	171	-	-	-	-	-	171	-	-	171
5725 to 5850 MHz
149	5745	17	17	-	-	-	17	17	-	-	-	17	17
153	5765	17	17	-	-	-	17	17	-	-	-	17	17
157	5785	17	17	-	-	-	17	17	-	-	-	17	17
161	5805	17	17	-	-	-	17	17	-	-	-	17	17
165	5825	-	-	-	-	-	-	-	-	-	-	-	-

1 Frequencies require DFS (Uniform spreading not required for the -P and -U regulatory domains).

Special Country Restrictions

Table 2-4 lists special restrictions for wireless operation in some countries.

Table 2-4 Special Country Restrictions for Wireless Operation

Country	Frequency Band (GHz)	Regulatory Domain	Special Limitation and Restrictions
Japan	5	-J, -P, and -U	Operation limited to indoor use only.
Mexico	2.4	-N	End user must limit 2.4 GHz operation to 2450 to 2483.5 MHz and 36 dBm EIRP1 .
Russian Federation	5	-E	End user must limit 5 GHz operation to 5150 to 5350 and 5650 to 5725 MHz.
United States	5	-A	Operation limited to indoor use only from 5150-5250 MHz.

1 EIRP (dBm) = maximum output power (dBm) + antenna gain (dBi)

Changing Access Point Output Power

This section provides instructions for changing the 1130AG series autonomous access point output power to comply with the maximum power limits imposed by special regulatory and country restrictions (see the "Special Country Restrictions" section).

---

Note Administrator privileges may be required in order to change access point settings.

---

---

Note Regulatory domains are set at the factory and cannot be changed by the user.

---

---

Caution To meet regulatory restrictions, the access point and the external antenna must be professionally installed. The network administration or other IT professional responsible for installing and configuring the unit is a suitable professional installer. Following configuration, access to the unit should be password protected by the network administrator to maintain regulatory compliance.

---

To change the access point output power level, follow these instructions:

---

Step 1 Use your web-browser to access your access point.

Step 2 When the Summary Status page appears, click Radio0-802.11G or Radio0-802.11A and the radio status page appears.

Step 3 Click Settings and the radio settings page appears.

Step 4 For the 802.11G radio, follow these steps:

a. Scroll down to the CCK Transmit Power (dBm) settings and click the desired output power level.

b. For the OFDM Transmit Power (dBm) settings, click the desired output power level.

Step 5 For the 802.11A radio, scroll down to the Transmit Power (dBm) settings and click the desired output power level.

Step 6 Scroll down to the bottom of the page and click Apply.

Step 7 Close your web-browser.

---