Table C-1 Access Point, Power Injector, and Power Module Specifications
Category
|
Access Point
|
Power Injector and Power Module
|
Size
|
Integrated antenna configuration:
8.00 in. W x 8.10 in. H 2.62 in. D
(20.32 cm W x 20.57 cm H 6.66 cm D)
|
Power injector:
4.62 in. W x 4.76 in. H x 1.07 in. D
(11.74 cm W x 12.09 cm H x 2.72 cm D)
Power module:
3.88 in. L x 1.24 in. W x 2.17 in. D
(98.5 mm L x 31.4 mm W x 55.0 mm D)
|
LEDs
|
Four LEDs on the back panel: Radio (R), Ethernet (E), Status (S), and Install (I).
|
One bi-color power LED on the side panel
|
Connectors
|
Bottom panel (left to right): Power injector dual-coax ports (two F-type connectors) and two reverse-TNC antenna connectors
|
Side panel (left to right): Two coaxial uplink F-type connectors, 48-VDC power connector, RJ-45 connector for 100BASE-T Ethernet, and a RJ-45 serial console port connector
|
Operating temperature
|
-22 to 131oF (-30 to 55oC)
|
Power injector:
-22 to 131oF (-30 to 55oC)
Power module:
32 to 104oF (0 to 40oC)
|
Non-operational temperature
|
-40 to 185oF (-40 to 85oC)
|
Power injector:
-40 to 185oF (-40 to 85oC))
Power module:
-40 to 185oF (-40 to 85oC)
(10,000 ft. limit)
|
Humidity
|
0 to 90% (condensing)
|
Power injector:
0 to 90% (non-condensing)
Power module:
0 to 95% (non-condensing)
|
Operational vibration
|
SAE J1455
|
Power injector—SAE J1455
|
Non-operational vibration
|
SAE J1455
|
Power injector—SAE J1455
|
Environmental testing compliance
|
The enclosure has been successfully tested and is in compliance with a NEMA 4 enclosure rating.
|
—
|
Weight
|
2.5 lbs (1.13 kg)
|
Power injector—0.8 lbs (0.36 kg)
Power module—1.0 lbs (0.5 kg)
|
Input voltage
|
48 VDC (nominal)
53 VDC (maximum)
|
Power injector (nominal):
48 VDC (LR2 power injector)
12 to 40 VDC (LR2T power injector)
Power module:
100 to 240 VAC
|
Power consumption
|
13W (typical)
|
—
|
Radio output power
|
For autonomous access points/bridges:
100, 50, 30, 20, 10, 5, or 1 mW
(at 1, 2, 5.5, and 11 Mbps)
30, 20, 10, 5, or 1 mW
(at 6, 9, 12, 18, 24, 48, and 54 Mbps)
For lightweight access points:
100, 50, 25, 12, 6, 3, 2, or 1 mW
(at 1, 2, 5.5, and 11 Mbps)
30, 15, 8, 4, 2, or 1 mW
(at 6, 9, 12, 18, 24, 48, and 54 Mbps)
(Depending on the regulatory domain in which the access point/bridge is installed)
|
Power injector:
18W (maximum at 48 VDC) supplied to the access point/bridge through dual-coax cables
Power module:
18W (maximum at 48 VDC)
|
Frequency
|
2.400 to 2.497 GHz
(Depending on the regulatory domain in which the access point/bridge is installed)
|
—
|
Modulation
|
IEEE 802.11b-compliant radio:
Direct Sequence Spread Spectrum (DSSS)
Complementary Code Keying (CCK)
IEEE 802.11g-compliant radio:
Orthogonal Frequency Division Multiplex (OFDM)
|
—
|
Subcarrier modulation
|
CCK (5.5 Mbps and 11 Mbps)
BPSK (1 Mbps, 6 Mbps and 9 Mbps)
QPSK (2 Mbps, 12 Mbps and 18 Mbps)
16-QAM (24 Mbps and 36 Mbps)
64-QAM (48 Mbps and 54 Mbps)
|
—
|
Data rates
|
IEEE 802.11b/g-compliant radio:
1, 2, 5.5 and 11 Mbps
6, 9, 12, 18, 24, 48, and 54 Mbps
(Depending on the regulatory domain in which the access point/bridge is installed)
|
—
|
Non-overlapping channels
|
3
|
—
|
Antenna
|
Integrated antenna
13-dBi patch array
Some external antennas:
5.2-dBi omnidirectional
12-dBi omnidirectional
9-dBi patch
10-dBi yagi
13.5-dBi yagi
14-dBi sector
21-dBi dish
(Depending on the regulatory region)
|
—
|
Environmental air space
|
The access point/bridge and power injector provide adequate fire resistance and low smoke-producing characteristics suitable for operation in a building's environmental air space, such as above suspended ceilings, in accordance with Section 300-22(C) of the National Electrical Code (NEC) and Sections 2-128, 12-010(3) and 12-100 of the Canadian Electrical Code, Part 1, C22.1.
Caution  The power module is not tested to UL 2043 and should not be placed in a building's air-handling spaces, such as above suspended ceilings.
|
Safety
|
UL 60950
UL 2043
CSA C22.2 No. 60950
IEC 60950
EN 60950
|
Power injector:
UL 2043
Power injector and power module:
UL 60950
CSA C22.2 No. 60950
IEC 60950
EN 60950
Note The power injector and power module must be used in an indoor environment.
|
Electromagnetic Compatibility (EMC)
|
FCC Part 15.107 and 15.109 Class B
ICES-003 Class B (Canada)
EN 55022 Class B
EN 55024
EN 60601-1-2:2001
AS/NZS 3548 Class B
VCCI Class B
EN 301.489-1
EN 301.489-17
|
FCC Part 15.107 and 15.109 Class B
ICES-003 Class B (Canada)
EN 55022 Class B
EN 55024
|
Radio type approvals
|
FCC Parts 15.247, 15.205, 15.209
FCC Bulletin OET-65C
Canada RSS-102, and RSS-210
Japan ARIB-STD-33B
Japan ARIB-STD-66
Europe EN 300.328
|
—
|
