Table Of Contents
Building the Table Assembly
Parts List
Where to Go Next
Building the Table Assembly
Revised: July 13, 2012, OL-21177-01
This chapter descibes the procedures you perform to install the table assembly.
Note 
You install all table sections in this chapter except the table door. You must install the presentation display and speaker screens before installing the table door as shown in Chapter 8 "Assembling and Mounting the Presentation Display, Speakers, Speaker Screens, and Table Door." After unpacking the table sections, keep the table door in a secure place until you are ready to install it.
Parts List
Key
|
Part Description
|
Part Number
|
Qty
|
Ctn
|
Notes
|
1
|
Tabletop leg
|
800-33522-01
Kit #69-2046-01
|
3
|
22
|
|
2
|
Tabletop leg for door (left)
|
800-33523-01
Kit #69-2046-01
|
1
|
22
|
|
3
|
Not used
|
|
|
|
|
4
|
Tabletop section: right-wing
|
700-23593-xx
|
1
|
21
|
|
5
|
Tabletop section: center-right
|
700-23594-xx
|
1
|
21
|
|
6
|
Tabletop section: center
|
700-23595-xx
|
1
|
21
|
|
7
|
Tabletop section: center-left
|
700-23596-xx
|
1
|
21
|
|
8
|
Not used
|
700-23597-xx
|
1
|
21
|
|
9
|
Connecting plate
|
700-27292-xx
|
12
|
21
|
|
10
|
Wooden biscuits
|
700-23909-xx
|
40
|
21
|
|
11
|
Not used
|
51-4539-xx
|
2
|
21
|
|
12
|
Not used
|
|
1
|
1
|
|
13
|
Cam lock rods
|
51-4579-xx
|
6
|
12
|
|
14
|
M4 x 12 mm pan head screws
|
48-2426-01
|
|
1
Sub-carton 1
|
|
15
|
M8 x 16 mm pan head screws, black
|
48-2430-01
|
|
1
Sub-carton 1
|
|
16
|
Not used
|
|
|
|
|
17
|
Cam lock
|
51-4580-xx
|
20
|
12
|
|
18
|
"Please close" label
|
47-21001-xx
|
1
|
1
Sub-carton 2
|
|
19
|
Table hinge safety strap
|
700-23825-xx
|
1
|
1
|
Use the screws included with the strap to attach.
|
20
|
Diamond-shaped connecting plate
|
700-23345-01
Kit #69-2032
|
1
|
2
|
|
21-25
|
Not used
|
|
|
1
|
|
26
|
Microphone
|
74-4743-xx
|
3
|
1
|
|
27
|
M4 x 30 screws
|
|
|
|
Included in microphone kit
|
28
|
M4 washers
|
|
|
|
Included in microphone kit
|
Caution The table segments are unstable during assembly. Use caution, and support all structures as required.
Caution Some system components have metal and plastic edges with hard angles. These edges are exposed until you complete system assembly. Use caution when you move around the system during assembly to avoid contact with any exposed system edges.
 |
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
|
Caution Table elements are heavy, and metal edges can be very sharp. Protect your hands and eyes from injury by wearing safety gloves and glasses.
Caution In order to prevent scratching the tabletops, you should avoid putting any tools on the table surfaces.
Note The directions left and right refer to the assembly as you face it from the front.
|
Warning Table legs are unstable until they are fully attached to the tabletop. Do not use unattached table legs as tabletop supports while you attach tabletop segments. They can fall and cause injury or damage.
|
Step 1 Attach the Right-wing tabletop section to the right tabletop section using the diamond-shaped connecting plate.
Note Each tabletop has clips on the underside of the tabletop. Remove all clips before you install each tabletop.
Figure 6-1 Right-wing tabletop section
Step 2 Attach the right Table segment using the cam lock, cam lock rods, plates, and screws.
Note Use the following guidelines when installing the cam locks and cam lock rods:
•Cam Lock rods have two adjustable halves that screw into a center piece. Make sure you screw the two halves of the Cam Lock rod equally into the center piece, so both halves are of equal length when inserted into the Cam Lock in each Table segment.
•While a cam lock is being tightened, hold the table edges together to avoid damage to the cam lock or the table segment.
•Use an Allen wrench to tighten the cam lock so the two table segments are connected snugly.
•While one person is tightening the cam locks from below, it is important for the support person to maintain the alignment of the table segment edges.
Figure 6-2 Right Table segment
Step 3 Attach the right-most Table Leg.
Figure 6-3 Right-most Table Leg
Step 4 Attach the center Table segment using the cam locks, cam lock rods, plates, and screws.
Figure 6-4 Center Table segment
Step 5 Attach the Right-center Table leg.
Figure 6-5 Right-center Table leg
Step 6 Attach the left Table segment.
a. Cam Lock rods have two adjustable halves that screw into a center piece. Make sure you screw the two halves of the Cam Lock rod equally into the center piece, so both halves are of equal length when inserted into the Cam Lock in each Table segment.
b. While a cam lock is being tightened, hold the table edges together to avoid damage to the cam lock or the table segment.
c. Use an Allen wrench to tighten the cam lock so the two table segments are connected snugly.
d. While one person is tightening the cam locks from below, it is important for the support person to maintain the alignment of the table segment edges.
Figure 6-6 Left Table segment
Step 7 Attach the left center Table leg.
Figure 6-7 Left center Table leg
Step 8 Attach the left-most Table leg.
Note The left-most Table leg is different from the other three table legs. It has only one flange on the right side of the leg, to attach to the left Table segment.
Figure 6-8 Left-most Table leg
Step 9 Attach the Microphones to the left, right, and center Table segments.
Note Steps for routing and connecting the microphone extension cables from the audio/video extension unit to the microphones are in Chapter 9 "Routing Power and Signal Cables."
Figure 6-9 Microphone Assembly
Step 10 Level the table and display shelves.
Tip Use a laser level inside of the table. Using this method, you can rotate the level 360 degrees and make sure that all table sections are level in relation to each other.
Figure 6-10 Leveling the Table Sections
Where to Go Next
Continue to Chapter 7 "Assembling the Cisco TelePresence Peripheral Electrical Components," to continue assembly of the Cisco TelePresence System.
Feedback
