Table Of Contents

McAfee Foundstone

Enable McAfee Foundstone 5.x and later to Use TCP/IP

Enable McAfee Foundstone (versions prior to 5.0) to Use TCP/IP

Add and Configure a McAfee Foundstone Device in MARS

McAfee Foundstone

---

To configure MARS to pull data from McAfee Foundstone (formerly known as Foundstone FoundScan), you must perform three tasks:

1. Configure McAfee Foundstone to enable data retrieval by MARS.

2. Add the McAfee Foundstone server to MARS using the web interface.

3. Schedule the interval at which the McAfee Foundstone server data is pulled by MARS.

This chapter contains the following topics:

•Enable McAfee Foundstone 5.x and later to Use TCP/IP

•Enable McAfee Foundstone (versions prior to 5.0) to Use TCP/IP

•Add and Configure a McAfee Foundstone Device in MARS

Enable McAfee Foundstone 5.x and later to Use TCP/IP

To enable TCP/IP on Foundstone 5.0 and 6.0, use the SQL Server Configuration Manager. As part of this configuraiton, you must disable the secure communications.

To enable the TCP/IP network protocol, perform the following steps:

---

Step 1 On the Start menu, choose All Programs, point to Microsoft SQL Server and then click SQL Server Configuration Manager.

---

Tip Optionally, you can open Computer Manager by right-clicking My Computer and choosing Manage. In Computer Management, expand Services and Applications, expand SQL Server Configuration Manager.

---

Step 2 Expand SQL Server Network Configuration, and then click Protocols forInstanceName.

Step 3 In the list of protocols, right-click the TCP/IP protocol, and then click Enable.

The icon for the protocol changes to show that the protocol is enabled.

Step 4 In the right pane, enable the IP address of the Local Controller that is monitoring this Foundstone server.

Step 5 Click Apply.

Step 6 Right-click on Protocols forInstanceName, and select Properties.

Step 7 In the Force Protocol Encryption box, verify the OFF option is selected.

This option disables secure communications between the MARS appliance and the Foundstone Server.

Step 8 Click OK to close Properties.

Step 9 Click OK to close SQL Server Configuration Manager.

---

Enable McAfee Foundstone (versions prior to 5.0) to Use TCP/IP

---

Note This procedure is only required for Foundstone versions prior to 5.0.

---

To configure McAfee Foundstone to provide data to MARS, follow these steps:

---

Step 1 Run command svrnetcn at the DOS prompt on the host where McAfee Foundstone is installed.

Step 2 In the SQL Server Network Utility dialog box, enable TCP/IP by moving TCP/IP from the Disabled Protocols list to Enabled Protocols list.

Step 3 Verify that the Force protocol encryption checkbox is cleared.

Step 4 Click Apply.

Step 5 Click OK to close SQL Server Network Utility.

---

Add and Configure a McAfee Foundstone Device in MARS

To add a McAfee Foundstone device in MARS, follow these steps:

---

Step 1 Select Admin > System Setup > Security and Monitor Devices > Add.

Step 2 Select Add SW Security apps on a new host or Add SW security apps on existing host from the Device Type list.

Step 3 Enter the device name and IP addresses if adding a new host.

Step 4 Click Apply.

Step 5 Click the Reporting Application tab.

Step 6 From the Select Application list, select McAfee Foundstone ANY.

Step 7 Click Add.

Step 8 Enter the following information:

•Database Name—The name for this database.

•Access Port—The default access port is 1433.

•Access Type—Verify the value is MS SQL.

•Login—The login information for the database.

•Password—The password for the database.

Step 9 Click Submit.

Step 10 Click Apply.

Once you activate this device (click Activate in the web interface), you must define the schedule at which MARS should pull data from it. For more information, see Scheduling Topology Updates, page 1-18.

---