Table Of Contents
Console and Auxiliary Port Cables and Pinouts
Console Port Cables and Pinouts
Auxiliary Port Signals and Pinouts
Cabling Specifications
This appendix provides the following cabling and pinout information for the Cisco AS5400 and Cisco AS5400HPX universal gateways:
•
Console and Auxiliary Port Cables and Pinouts
Note
Note
Console and Auxiliary Port Cables and Pinouts
The universal gateway arrives with a console and auxiliary cable kit, which contains the cable and adapters you need to connect a console (an ASCII terminal or PC running terminal emulation software) or modem to your universal gateway. The console and auxiliary cable kit includes:
•
•
•
•
For console connections, proceed to the section "Console Port Cables and Pinouts" on page C-2. For modem connections, proceed to the section "Auxiliary Port Signals and Pinouts" on page C-4.
Identifying a Rollover Cable
You can identify a rollover cable by comparing the two modular ends of the cable. Holding the cables side by side, with the tab at the back, the wire connected to the pin on the outside of the left plug should be the same color as the wire connected to the pin on the outside of the right plug. (See Figure C-1.) If your cable was purchased from Cisco Systems, pin 1 will be white on one connector, and pin 8 will be white on the other connector (a rollover cable reverses pins 1 and 8, 2 and 7, 3 and 6, and 4 and 5).
Figure C-1 Identifying a Rollover Cable
Console Port Cables and Pinouts
Use the RJ-45-to-RJ-45 rollover cable and RJ-45-to-DB-9 female DTE adapter (labeled TERMINAL) to connect the console port to a PC running terminal emulation software. Figure C-2 shows how to connect the console port to a PC. Table C-1 lists the pinouts for the asynchronous serial console port, the RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-9 female DTE adapter (labeled TERMINAL).
Figure C-2 Connecting the Console Port to a PC
Table C-1 Console Port Signaling and Cabling Using a DB-9 Adapter
RTS
11
8
8
CTS
DTR
2
7
6
DSR
TxD
3
6
2
RxD
GND
4
5
5
GND
GND
5
4
5
GND
RxD
6
3
3
TxD
DSR
7
2
4
DTR
CTS
81
1
7
RTS
1 Pin 1 is connected internally to pin 8.
Use the RJ-45-to-RJ-45 rollover cable and RJ-45-to-DB-25 female DTE adapter (labeled TERMINAL) to connect the console port to a terminal. Figure C-3 shows how to connect the console port to a terminal. Table C-2 lists the pinouts for the asynchronous serial console port, the RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-25 female DTE adapter (labeled TERMINAL).
Figure C-3 Connecting the Console Port to a Terminal
Table C-2 Console Port Signaling and Cabling Using a DB-25 Adapter
RTS
12
8
5
CTS
DTR
2
7
6
DSR
TxD
3
6
3
RxD
GND
4
5
7
GND
GND
5
4
7
GND
RxD
6
3
2
TxD
DSR
7
2
20
DTR
CTS
81
1
4
RTS
1 You can use the same cabling to connect a console to the auxiliary port.
2 Pin 1 is connected internally to pin 8.
Auxiliary Port Signals and Pinouts
Use the RJ-45-to-RJ-45 rollover cable and RJ-45-to-DB-25 male DCE adapter (labeled MODEM) to connect the auxiliary port to a modem. Figure C-4 shows how to connect the auxiliary port to a modem. Table C-3 lists the pinouts for the asynchronous serial auxiliary port, the RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-25 male DCE adapter (labeled MODEM).
Figure C-4 Connecting the Auxiliary Port to a Modem
Ethernet Port Pinouts
Table C-4 lists the pinouts for the Ethernet ports.
Table C-4 10/100BASE-T Port Pinouts
1
TXD+
2
TXD-
3
RXD+
4
-
5
-
6
RXD-
7
-
8
-
BITS Cable and Port Pinouts
Figure C-5 shows how the BITS port is connected and Table C-5 lists the BITS port pinouts.
Figure C-5 BITS Port Connection
Alarm Port Pinouts
Table C-6 lists the pinouts for the alarm port.
Bantam Jack Port Pinouts
Table C-7 lists the port pinouts for the bantam jacks on the AS54-DFC-8CT1/CE1 and AS54-DFC-CT3.
