Table Of Contents
Change Node Settings
Before You Begin
NTP-C78 Change Node Management Information
NTP-C79 Change CTC Network Access
NTP-C133 Modify OSI Provisioning
NTP-C80 Customize the CTC Network View
NTP-C143 Modify or Delete Card Protection Settings
NTP-C82 Change Node Timing
NTP-C83 Modify Users and Change Security
NTP-C84 Change SNMP Settings
NTP-C85 Modify or Delete Communications Channel Terminations and Provisionable Patchcords
Change Node Settings
Note 
The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration. Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's path protection feature, which may be used in any topological network configuration. Cisco does not recommend using its path protection feature in any particular topological network configuration.
This chapter explains how to modify node provisioning for the Cisco ONS 15310-CL and Cisco ONS 15310-MA. To provision a new node, see Chapter 4 "Turn Up a Node." To change default card-level and node-level settings, refer to the "Network Element Defaults" appendix in the Cisco ONS 15310-CL and Cisco ONS 15310-MA Reference Manual.
Before You Begin
Before performing the following procedures, investigate all alarms and clear any trouble conditions. Refer to the Cisco ONS 15310-CL and Cisco ONS 15310-MA Troubleshooting Guide as necessary.
This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).
1. C78 Change Node Management Information—As needed, complete this procedure to change the node name, contact information, latitude, longitude, date, time, and login legal disclaimer.
2. C79 Change CTC Network Access—As needed, complete this procedure to change the IP address, default router, subnet mask, network configuration settings, and static routes.
3. C133 Modify OSI Provisioning—Complete this procedure as needed to modify Open System Interconnection (OSI) parameters including the OSI routing mode, Target Identifier Address Resolution Protocol (TARP), routers, subnets, and IP-over-OSI tunnels.
4. C80 Customize the CTC Network View—As needed, complete this procedure to customize the appearance of the network map, including specifying the default map, selecting your own map or image, consolidating links, and changing the background color.
5. C143 Modify or Delete Card Protection Settings—Complete as needed.
6. C82 Change Node Timing—Complete as needed.
7. C83 Modify Users and Change Security—As needed, complete this procedure to change the security policy on one or more nodes, change the node access and PM clearing privilege, grant superuser privileges to provisioning users, change the user password and security settings on one or more nodes, delete and logout users on one or more nodes, and configure the node for RADIUS authentication.
8. C84 Change SNMP Settings—Complete as needed.
9. C85 Modify or Delete Communications Channel Terminations and Provisionable Patchcords—Complete as needed.
NTP-C78 Change Node Management Information
Purpose
|
This procedure changes basic information about the node such as node name, date, time, contact information, and the login legal disclaimer.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
C20 Set Up Name, Date, Time, and Contact Information
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Step 1 Complete the "DLP-C29 Log into CTC" task. If you are already logged in, continue with Step 2.
Step 2 Complete the "NTP-C102 Back Up the Database" procedure.
Step 3 As needed, complete the "DLP-C123 Change the Node Name, Date, Time, and Contact Information" task.
Step 4 As needed, complete the "DLP-C124 Change the Login Legal Disclaimer" task.
Step 5 After confirming the changes, complete the "NTP-C102 Back Up the Database" procedure.
Stop. You have completed this procedure.
NTP-C79 Change CTC Network Access
Purpose
|
This procedure changes essential network information, including IP settings, static routes, and OSPF options.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
C21 Set Up CTC Network Access
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note Additional ONS 15310-CL and ONS 15310-MA networking information and procedures, including IP addressing examples, static route scenarios, Open Shortest Path First (OSPF) protocol, routing information protocol options, and Open System Interconnection (OSI) information, are provided in the "Management Network Connectivity" chapter of the Cisco ONS 15310-CL and Cisco ONS 15310-MA Reference Manual.
Step 1 Complete the "DLP-C29 Log into CTC" task. If you are already logged in, continue with Step 2.
Step 2 Complete the "NTP-C102 Back Up the Database" procedure.
Step 3 Perform any of the following tasks as needed:
•C125 Change IP Settings
•C40 Create a Static Route
•C126 Modify a Static Route
•C127 Delete a Static Route
•C128 Disable Open Shortest Path First Protocol
•C41 Set Up or Change Open Shortest Path First Protocol
•C47 Provision a Proxy Tunnel
•C129 Delete a Proxy Tunnel
•C48 Provision a Firewall Tunnel
•C130 Delete a Firewall Tunnel
Step 4 Complete the "NTP-C102 Back Up the Database" procedure.
Stop. You have completed this procedure.
NTP-C133 Modify OSI Provisioning
Purpose
|
This procedure modifies the ONS 15310-CL and ONS 15310-MA OSI parameters including the OSI routing mode, TARP, routers, subnets, and IP-over-CLNS tunnels.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
C131 Provision OSI
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note The "Management Network Connectivity" chapter of the Cisco ONS 15310-CL and Cisco ONS 15310-MA Reference Manual includes additional information about the ONS 15310-CL or
ONS 15310-MA implementation of OSI.
Step 1 Complete the "DLP-C29 Log into CTC" task. If you are already logged in, continue with Step 2.
Step 2 Complete the "NTP-C102 Back Up the Database" procedure.
Step 3 Perform any of the following tasks as needed:
•C201 Provision or Modify TARP Operating Parameters
•C202 Add a Static TID to NSAP Entry to the TARP Data Cache
•C203 Remove a Static TID to NSAP Entry from the TARP Data Cache
•C204 Add a TARP Manual Adjacency Table Entry
•C209 Remove a TARP Manual Adjacency Table Entry
•C235 Change the OSI Routing Mode
•C211 Edit the OSI Router Configuration
•C212 Edit the OSI Subnetwork Point of Attachment
•C208 Create an IP-Over-CLNS Tunnel
•C214 Delete an IP-Over-CLNS Tunnel
Step 4 Complete the "NTP-C102 Back Up the Database" procedure.
Stop. You have completed this procedure.
NTP-C80 Customize the CTC Network View
Purpose
|
This procedure modifies the CTC network view, including grouping nodes into domains for a clearer display, changing the network view background color, and using a custom image for the network view background.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
None
|
Required/As needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Superuser
|
Step 1 Complete the "DLP-C29 Log into CTC" task. If you are already logged in, continue with Step 2.
Step 2 Complete the following tasks, as needed:
•C131 Change the Network View Background Color
•C132 Change to the Default Network View Background Map
•C133 Apply a Custom Network View Background Map
•C134 Create Domain Icons
•C135 Manage Domain Icons
•C136 Enable Dialog Box Do-Not-Display Option
•C229 Consolidate Links in Network View
Stop. You have completed this procedure.
NTP-C143 Modify or Delete Card Protection Settings
Caution Modifying and deleting protection groups can be service affecting.
Step 1 Complete the "DLP-C29 Log into CTC" task. If you are already logged in, continue with Step 2.
Step 2 Complete the "NTP-C102 Back Up the Database" procedure.
Step 3 For the ONS 15310-CL, perform any of the following tasks as needed:
•C137 Modify a 1+1 Protection Group
•C138 Delete a Protection Group
Step 4 For the ONS 15310-MA, perform any of the following tasks as needed:
•C245 Modify a 1:1 Protection Group for the ONS 15310-MA
•C137 Modify a 1+1 Protection Group
•C244 Modify an Optimized 1+1 Protection Group for the ONS 15310-MA
•C138 Delete a Protection Group
Note 1:1 protection groups are created automatically and can only be deleted when the protect card of a 1:1 protection group is deleted.
Step 5 Complete the "NTP-C102 Back Up the Database" procedure.
Stop. You have completed this procedure.
NTP-C82 Change Node Timing
Purpose
|
This procedure changes the SONET timing settings for the ONS 15310-CL and ONS 15310-MA.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
C23 Set Up Timing
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Caution Internal timing is Stratum 3 and not intended for permanent use. All ONS 15310-CL and
ONS 15310-MA nodes should be timed to a Stratum 2 or better primary reference source.
Step 1 Complete the "DLP-C29 Log into CTC" task. If you are already logged in, continue with Step 2.
Step 2 Complete the "NTP-C102 Back Up the Database" procedure.
Step 3 As needed, complete the "DLP-C139 Change the Node Timing Source" task.
Step 4 If you need to change any internal timing settings, follow the "DLP-C46 Set Up Internal Timing" task for the settings you need to modify.
Step 5 If you need to verify timing after removing a node from a path protection, see the "DLP-C140 Verify Timing in a Reduced Ring" task.
Step 6 Complete the "NTP-C102 Back Up the Database" procedure.
Stop. You have completed this procedure.
NTP-C83 Modify Users and Change Security
Purpose
|
This procedure modifies user and security properties for the ONS 15310-CL or ONS 15310-MA.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
C19 Create Users and Assign Security
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Superuser only
|
Step 1 Complete the "DLP-C29 Log into CTC" task. If you are already logged in, continue with Step 2.
Step 2 Complete the "NTP-C102 Back Up the Database" procedure.
Step 3 Perform any of the following tasks as needed:
•C141 Change the Security Policy on a Single Node
•C142 Change the Security Policy on Multiple Nodes
•C143 Change Node Access and PM Clearing Privilege
•C234 Grant Superuser Privileges to Provisioning Users
•C144 Change User Password and Security Settings on a Single Node
•C145 Change User Password and Security Settings on Multiple Nodes
•C146 Delete a User on a Single Node
•C147 Delete a User on Multiple Nodes
•C148 Log Out a User on a Single Node
•C149 Log Out a User on Multiple Nodes
•C196 Configure the Node for RADIUS Authentication
Step 4 Complete the "NTP-C102 Back Up the Database" procedure.
Stop. You have completed this procedure.
NTP-C84 Change SNMP Settings
Purpose
|
This procedure modifies SNMP settings for the ONS 15310-CL and
ONS 15310-MA.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
C25 Set Up SNMP
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Superuser only
|
Step 1 Complete the "DLP-C29 Log into CTC" task. If you are already logged in, continue with Step 2.
Step 2 Complete the "NTP-C102 Back Up the Database" procedure.
Step 3 Perform any of the following tasks as needed:
•C150 Modify SNMP Trap Destination
•C151 Delete SNMP Trap Destinations
Step 4 Complete the "NTP-C102 Back Up the Database" procedure.
Stop. You have completed this procedure.
NTP-C85 Modify or Delete Communications Channel Terminations and Provisionable Patchcords
Caution Deleting a DCC termination can cause you to lose visibility of nodes that do not have other DCCs or network connections to the CTC computer.
Step 1 Complete the "DLP-C29 Log into CTC" task. If you are already logged in, continue with Step 2.
Step 2 As needed, complete the following tasks to modify data communication channel settings:
•C152 Change a Section DCC Termination
•C153 Change a Line DCC Termination
Step 3 As needed, complete the following tasks to delete data communication channel terminations:
•C154 Delete a Section DCC Termination.
•C155 Delete a Line DCC Termination.
Step 4 As needed, complete the "DLP-C156 Delete a Provisionable Patchcord" task.
Stop. You have completed this procedure.
Feedback
