Table Of Contents

Mapping LMS 3.2 Features and Terminologies to LMS 4.2 functions

Mapping LMS 3.2 Features in Monitor

Mapping IPM Features and Terminologies in Monitor

Mapping HUM Features and Terminologies in Monitor

Mapping DFM Features and Terminologies in Monitor

Mapping LMS 3.2 Features in Inventory

Mapping Common Services Features and Terminologies in Inventory

Mapping RME Features and Terminologies in Inventory

Mapping CM Features and Terminologies in Inventory

Mapping IPM Features and Terminologies in Inventory

Mapping CiscoView Features and Terminologies in Inventory

Mapping DFM Features and Terminologies in Inventory

Mapping LMS 3.2 Features in Configuration

Mapping RME Features and Terminologies in Configuration

Mapping CM Features and Terminologies in Configuration

Mapping LMS 3.2 Features in Reports

Mapping RME Reports and Terminologies in Reports

Mapping CS Reports and Terminologies in Reports

Mapping CM Reports and Terminologies in Reports

Mapping HUM Reports and Terminologies in Reports

Mapping DFM Reports and Terminologies in Reports

Mapping IPM Reports and Terminologies in Reports

Mapping LMS 3.2 Features in Admin

Mapping RME Features and Terminologies in Admin

Mapping CS Features and Terminologies in Admin

Mapping CM Features and Terminologies in Admin

Mapping HUM Features and Terminologies in Admin

Mapping DFM Features and Terminologies in Admin

Mapping IPM Features and Terminologies in Admin

Mapping LMS 3.2 Features and Terminologies to LMS 4.2 functions

---

This chapter provides information on the LMS 3.2 features and terminologies mapped to LMS 4.2 functions.

CiscoPrime LMS 4.2 has the following core functions in this release:

•Monitor (See Mapping LMS 3.2 Features in Monitor)

•Inventory (See Mapping LMS 3.2 Features in Inventory)

•Configuration (See Mapping LMS 3.2 Features in Configuration)

•Reports (See Mapping LMS 3.2 Features in Reports)

•Admin (See Mapping LMS 3.2 Features in Admin)

•Work Center (Features in this function are new in LMS 4.2)

Mapping LMS 3.2 Features in Monitor

Monitoring and Troubleshooting in LMS allows you to monitor the health and performance of network devices, notifies the list of active problems on the network and the changes occurring on the network, and helps you to identify the problems from a single place.

LMS provides you with monitoring dashboards and tools that provide summarized information about the health of the network and allows you to monitor the network.

Features in Monitor function are derived from the following LMS 3.2 applications:

•Internetwork Performance Monitor (IPM), see Mapping IPM Features and Terminologies in Monitor.

•Cisco Prime Health and Utilization Monitor (HUM), see Mapping HUM Features and Terminologies in Monitor.

•Device Fault Manager (DFM), see Mapping DFM Features and Terminologies in Monitor.

See Monitoring and Troubleshooting With Cisco Prime LAN Management Solution 4.2for more information.

Mapping IPM Features and Terminologies in Monitor

This section provides information on the IPM features and terminologies mapped in Monitor function in LMS 4.2.

Table 9-1 Mapping IPM Features in Monitor 

IPM Features	Monitor Function	Description
Collectors	Collectors Monitor> Performance Settings> IPSLA> Collectors	Collector feature in Monitor allows you to manage the collector details and also provides the various collector status and their validation details.
Devices	Devices Monitor> Performance Settings> IPSLA> Devices	Device feature in Monitor allows you to: •Add adhoc target devices •Edit the device attributes •Update the IPSLA responder enable or disable status •Enable responder for the selected devices. •Delete devices from managing IPSLA Monitoring functionality
Operations	Operations Monitor> Performance Settings> IPSLA> Operations	IPSLA is a portfolio of technology embedded in most devices that run Cisco IOS software. IPSLA Monitoring supports the following IP SLA operations: •Echo Operations •Jitter Operations •VoIP Operations •Operation based on Services •Metro Ethernet Operations
Outage Settings	Outage Settings Monitor> Performance Settings> IPSLA> Outage Settings	Outages or downtime refers to the time span when the network fails to provide its primary function. Outage Settings in Monitor allows you to can create, edit, and delete planned outage.

Mapping HUM Features and Terminologies in Monitor

This section provides information on the HUM features and terminologies mapped in Monitor function in LMS 4.2.

Table 9-2 Mapping HUM Features in Monitor 

HUM Features	Monitor Function	Description
Threshold Setup	Performance Monitor > Threshold Settings > Performance	Performance feature in Monitor allows you to: •Create a Threshold •Edit a Threshold •Delete a Threshold •Filter Thresholds •View Threshold Configuration Details
Poller Management	Pollers Monitor > Performance Settings > Setup > Pollers	Poller feature in Monitor allows you to: •Create a Poller •Modify the configuration of a Poller •Delete a Poller •Stop a Poller from polling the devices •View polling failures
Template Management	Templates Monitor > Performance Settings > Setup > Templates	Template feature in Monitor allows you to: •Create a user-defined template •Modify the configuration of a user-defined template •Export a user-defined template •Import a user-defined template •Delete a user-defined template
TrendWatch Setup	TrendWatch Monitor > Threshold Settings > TrendWatch	TrendWatch feature in Monitor allows you to: •Create a TrendWatch •Edit a TrendWatch •Delete a TrendWatch •Deactivate a TrendWatch •Activate a TrendWatch •Copy a TrendWatch •Filter TrendWatch

Mapping DFM Features and Terminologies in Monitor

This section provides information on the DFM features and terminologies mapped in Monitor function in LMS 4.2.

Table 9-3 Mapping DFM Features in Monitor 

DFM Features	Monitor Function	Description
Fault Monitor	Fault Monitor Monitor > Monitoring Tools > Fault Monitor	Fault Monitor is a centralized browser where you can view the information on faults, system events, and performance management events of devices in a single place.
Managing Thresholds	Threshold Settings Monitor > Fault Settings > Setup > Threshold Settings	Threshold Settings feature in Monitor will allow you to manage thresholds for: •All devices managed by LMS Monitoring •LMS System Defined Groups •Customizable Fault Groups (for devices) •System Defined Fault groups, for example Access Port Groups, Interface Groups and Trunk Port Groups and their own sub groups.
Polling Parameters	Polling Parameters Monitor > Fault Settings > Setup > Polling Parameters	Polling Parameter feature in Monitor allows you to: •View Polling Parameters •Preview Polling Parameters •Edit Polling Parameters •Restore Factory Setting Polling Parameters •Restore Factory Setting Polling Parameters •Set Device Polling
Setting Priorities	Priority Settings Monitor > Fault Settings > Setup > Priority Settings	Priority Setting feature in Monitor allows you to change the priorities of System-defined groups and customizable groups.
SNMP Trap Notification	Notification Monitor > Fault Settings > SNMP Traps > Notification	Notification feature in Monitor allows you to view information related to subscription, subscription status and notification group.
Device Details	Fault Device Details Monitor > Fault Settings > Setup > Fault Device Details	You can view the details of fault devices in LMS.

Mapping LMS 3.2 Features in Inventory

Inventory Management in Cisco Prime LAN Management Solution (LMS) 4.2 groups the various activities in LMS involved in managing your network devices. You can add devices, discover devices, manage them, and manage groups using Inventory Management.

It also provides various Inventory Tools like Ciscoview, Mini-RMON, and SmartCase.

Features in Inventory Management are derived from the following LMS 3.2 applications:

•CiscoWorks Common Services (CS), see Mapping Common Services Features and Terminologies in Inventory.

•CiscoWorks Resource Manager Essentials (RME), see Mapping RME Features and Terminologies in Inventory

•CiscoWorks Campus Manager (CM), see Mapping CM Features and Terminologies in Inventory.

•CiscoWorks Internetwork Performance Monitor (IPM), see Mapping IPM Features and Terminologies in Inventory.

•CiscoWorks CiscoView (CV), see Mapping CiscoView Features and Terminologies in Inventory

•CiscoWorks Device Fault Manager (DFM), see Mapping DFM Features and Terminologies in Inventory.

See Configuration Management with Cisco Prime LAN Management Solution 4.2 for more information.

Mapping Common Services Features and Terminologies in Inventory

This section provides information on the CS features and terminologies mapped in Inventory Management in LMS 4.2.

Table 9-4 Mapping CS Features in Inventory Management 

CS Features	Inventory Function	Description
Device Management	Device Management (Inventory > Device Administration > Add / Import / Manage Devices)	Device Management feature in Configuration allows you to: •Add Devices •Delete Devices •Edit Device Credentials •Edit Device Identity •Import Devices and Credentials •Export Devices and Credentials •Exclude Devices •View Devices List •Verify Device Credentials
Device Discovery	Discovery (Inventory > Device Administration > Discovery )	Discovery feature in Inventory allows you to peform: •View Device Discovery Summary •Schedule a Device Discovery •Configure Device Discovery Settings
Alias Devices	Device Aliases (Inventory > Device Administration > Device Aliases)	Device Aliases feature in Inventory allows you to resolve Alias devices.
Auto Update Server Management	Auto Update Server Management (Inventory > Device Administration > Auto Update Server Management)	Auto Update Server management feature helps you to add, edit, or delete Auto Update Server.
Groups	Device Group Administration (Inventory > Group Management > Device)	LMS 4.2 combines the device grouping with a new attribute list. The Unified Grouping Services can support 600 groups.
Device Center	Device Center: Device Diagnostics (Inventory > Tools > Device Center)	Device Center provides a central point from where you can see a summary and reports for the selected device, invoke various tools on the selected device, and perform the tasks that can be performed on the selected device.

Mapping RME Features and Terminologies in Inventory

This section provides information on the RME features and terminologies mapped in Inventory Management in LMS 4.2.

Table 9-5 Mapping RME Features in Inventory Management 

RME Features	Inventory Function	Description
Group Administration	Device Group Administration (Inventory > Group Management > Device)	LMS 4.2 combines the device grouping with a new attribute list. The Unified Grouping Services can support 600 groups.
SmartCase	SmartCase (Inventory > Tools > SmartCase)	SmartCase lets you access Cisco.com to open a Cisco.com case or to query and update an existing case. You can submit, review, and update problems or questions about your Cisco products.
Port and Module Group Admin	Port and Module Group Browser (Inventory > Group Management > Port and Module)	You can create groups based on ports and modules for a selected set of devices or device groups.
Device Credential Verification Jobs	Device Credential Verification (Inventory > Job Browsers > Device Credentials Verification)	You can verify device credentials and view a detailed list of all scheduled CDA jobs.
Inventory Jobs	Inventory Collection (Inventory > Job Browsers > Inventory Collection)	Displays all user-defined inventory jobs. It also displays the system-defined inventory collection and polling jobs.

Mapping CM Features and Terminologies in Inventory

This section provides information on the CM features and terminologies mapped in Inventory Management in LMS 4.2.

Table 9-6 Mapping CM Features in Inventory Management 

CM Features	Inventory Function	Description
Group Administration	Device Group Administration (Inventory > Group Management > Device)	LMS 4.2 combines the device grouping with a new attribute list. The Unified Grouping Services can support 600 groups.
Acquisition Actions	Acquisition Actions (Inventory > User Tracking Settings > Acquisition Actions)	You can trigger the following acquisitions: •Device based Acquisition •Subnet based Acquisition IP Phone Acquisition
Acquisition	Acquisition Summary (Inventory > User Tracking Settings > Acquisition Summary)	You can view acquisition information.

Mapping IPM Features and Terminologies in Inventory

This section provides information on the IPM features and terminologies mapped in Inventory Management in LMS 4.2.

Table 9-7 Mapping IPM Features in Inventory Management 

IPM Features	Inventory Function	Description
Devices	IPSLA Devices (Inventory > Device Administration > IPSLA Devices)	For IPSLA Monitoring function work with devices, you must first add devices from Device Credential Repository (DCR). You can also add adhoc target devices for IPSLA Monitoring.
Group Admin	IPSLA Collector Groups (Inventory > Group Management > IPSLA Collector)	You can manage IPSLA Collector groups.

Mapping CiscoView Features and Terminologies in Inventory

This section provides information on the CiscoView features and terminologies mapped in Inventory Management in LMS 4.2.

Table 9-8 Mapping CiscoView Features in Inventory Management 

CiscoView Features	Inventory Function	Description
CiscoView	CiscoView (Inventory > Tools > CiscoView)	CiscoView is a graphical SNMP-based device management tool that provides real-time views of networked Cisco Systems devices.
Mini-RMON	Mini-RMON (Inventory > Tools > Mini-RMON )	Mini-RMON is a real-time remote monitoring tool that provides option to enable RMON collection, display the collected ethernet statistics and lets you set thresholds against any of thecollected statistics.

Mapping DFM Features and Terminologies in Inventory

This section provides information on the DFM features and terminologies mapped in Inventory Management in LMS 4.2.

Table 9-9 Mapping DFM Features in Inventory Management 

CiscoView Features	Inventory Function	Description
Group Administration	Fault Groups (Inventory > Group Management > Fault)	You can manage fault groups.

Mapping LMS 3.2 Features in Configuration

Configuration management in Cisco Prime LMS 4.2 allows you to manage, deploy and modify the configuration files used by devices in your network.

Configuration function allows you to:

•Run tools that can compare configuration files and perform software image management tasks.

•Create configuration jobs

•Manage configuration archive settings

•Define baseline configuration templates and determine the devices that are non-compliant in your network

•Perform VLANs configurations

•Create and manage Virtual Switching System (VSS) conversions

Features in Configuration function are derived from the following LMS 3.2 applications:

•CiscoWorks Resource Manager Essentials (RME), see Mapping RME Features and Terminologies in Configuration.

•CiscoWorks Campus Manager (CM), see Mapping CM Features and Terminologies in Configuration.

See Configuration Management with Cisco Prime LAN Management Solution 4.2 for more information.

Mapping RME Features and Terminologies in Configuration

This section provides information on the RME features and terminologies mapped in Configuration function in LMS 4.2.

Table 9-10 Mapping RME Features in Configuration 

RME Features	Configuration Function	Description
Software Management	Software Image Management (Configuration > Software Image Management)	Software image management feature in Configuration allows you to perform: •Patch Distribution •Software Distribution •Software Repository •Repository Synchronization •Upgrade Analysis •Jobs
VSS Config	Virtual Switching System (Configuration > Workflows)	VSS feature in Configuration allows you to peform: •VSS Conversion •VSS Reverse Conversion
Archive Mgmt	Configuration Archive (Configuration > Configuration Archive)	Configuration Archive feature in Configuration allows you to: •View Configuration archival summary •Create Custom Queries •Search Archives •View Version Summary •View Version Tree •Synchronization configurations •Compare Config files •Create Label Configs •View Protocol Usage Summary
NetConfig	NetConfig (Configuration > Tools: NetConfig)	NetConfig feature in Configuration allows you to: •Deploy configurations •Assigning Tasks •Create User Defined Tasks
Config Editor	Config Editor (Configuration > Tools:Config Editor)	Config Editor feature in Configurtion allows you to: •Open configuration files for editing •Edit Private Configs •Edit Public Configs •Set Edit Mode Preferences
Template Mgmt	Compliance (Configuration > Compliance)	Compliance feature in Configuration allows you to: •Manage Baseline Templates •Run Compliance Check •Deploy Baseline templates •View the status of Baseline jobs •Generate Out-of-Sync summary report
Compliance Check
Direct Deploy
Compliance/Deploy Jobs	Compliance (Configuration > Job Browsers: Compliance)	You can check the status of the Baseline jobs.

Mapping CM Features and Terminologies in Configuration

This section provides information on the CM features and terminologies mapped in Configuration function in LMS 4.2.

Table 9-11 Mapping CM Features in Configuration

CM Features	Configuration Function	Description
Topology Services	Topology (Configuration > Topology)	Topology feature in Configuration allows you to view and monitor your network including the links and the ports of each link. Topology Services displays the network topology of the devices discovered by LMS through Topology Maps.
Configuration	VLAN (Configuration > Workflows: VLAN)	VLAN feature in Configuration allows you to: •Configure VLAN •Delete VLAN •Create Private VLAN •Delete Private VLAN •Configure Port Assignment •Configure Promiscuous Ports •Create Trunk •Modify Trunk Attributes
Virtual Network Manager (VNM)	VRF Lite (Configuration > Workflows: VRF Lite)	VRF Lite feature in Configuration allows you to: •Create VRF •Edit VRF •Extend VRF •Delete VRF •Edge VLAN Configuration

Mapping LMS 3.2 Features in Reports

Reports Management in Cisco Prime LAN Management Solution 4.2 provides a single launch point for all the reports that can be generated and viewd in Cisco Prime LMS 4.2.

All the reports have been grouped under various heads based on the information displayed.

In Cisco Prime LAN Management Solution 4.2, the reports have been categorized as:

•Inventory Reports

•Switch Port Report

•Technology Reports

•Fault and Events Reports

•Performance Reports

•Online Reports

•System Reports

•Audit Reports

•Report Designer

•Report Settings

•Report Archives

The various reports have been from the following LMS 3.2 applications:

•CiscoWorks Resource Manager Essentials (RME), see Mapping RME Reports and Terminologies in Reports.

•CiscoWorks Common Services (CS), see Mapping CS Reports and Terminologies in Reports.

•CiscoWorks Campus Manager (CM), see Mapping CM Reports and Terminologies in Reports.

•CiscoWorks Health and Utilization Monitor (HUM), see Mapping HUM Reports and Terminologies in Reports.

•CiscoWorks Device Fault Manager (DFM), see Mapping DFM Reports and Terminologies in Reports.

•CiscoWorks Internetwork Performance Monitor (IPM), see Mapping IPM Reports and Terminologies in Reports.

See Reports Management with CiscoPrime LAN Management Solution 4.2 for more information.

Mapping RME Reports and Terminologies in Reports

Table 9-12 Mapping RME Features and Terminologies in Admin

RME Reports	Name of the report in LMS 4.2	Description
AuditTrail Report	Inventory and Config (Reports > Audit > Inventory and Config)	This option lets you compile a report on all Audit Trail changes that occurred in the network during a specific time period.
BugToolkit Reports	Bug Summary (Reports > Cisco.com > Bug Summary)	You can generate reports based on bugs filed against IOS and CATOS devices that are managed in the your network.
ChangeAudit Report	Standard (Reports > Audit > Change Audit > Standard)	This option lets you compile a report on all changes that occurred in the network during a specific time period. You can compile a report based on the selection criteria, such as application, users, connection mode.
Contract Connection Reports	Contract Connection (Reports > Cisco.com > Contract Connection)	Cisco Contract Connection lets you verify which of your Cisco IOS devices are covered by a service contract. Contract Connection (CC) uses Inventory Manager, Cisco.com, and Cisco's internal contract tracking service, Contract Agent, to provide the status of your service coverage.
Check Device Credential Reports	Credential Verification (Reports > Inventory > Management Status > Credential Verification)	The Credential Verification Report displays the names and the credential status for each device. This report can be used to view the static device credentials
Inventory Reports	Detailed Device (Reports > Inventory > Detailed Device)	You can display complete inventory information for selected devices.
Syslog Reports	Syslog (Reports > Fault and Event > Syslog )	You can generate a system message report for a device or set of devices.
Custom Report Templates	Custom Report Template (Reports > Report Designer > Syslog and Inventory > Custom Report Template)	The Custom Templates option lets you create new report templates customized according to your requirements. You can also edit, or delete existing custom templates.
Report Archives	Report Archives (Reports > Report Archives > Inventory and Syslog)	The report output that is created from a scheduled report is stored in the reports archive. The archive displays the list for completed report jobs and you can view or delete them.

Mapping CS Reports and Terminologies in Reports

Table 9-13 Mapping RME Features and Terminologies in Admin

CS Reports	Name of the report in LMS 4.2	Description
System Report	Status Reports > System > Status > Log File Reports > System > Status > Process Users Reports > System > Users > Permission Reports > System > Users > Who is Logged On System Reports > Audit > System.	This option lets you compile a report on all Audit Trail changes that occurred in the network during a specific time period.
Device List Report	Known Device List Reports > Inventory > Management Status > Known Device List	The Device List Report displays the complete list and information of all devices in the repository.
Audit Report
Excluded Devices Report	Excluded Devices Reports > Inventory > Management Status > Excluded Devices	The Excluded Devices Report displays the list of devices that should not be added in DCR.
Import Status Report	Imported Device Status Reports > Inventory > Management Status > Imported Device Status	The Imported Device List Report displays the information about the devices that are imported into DCR.
Unreachable Device Report	Unreachable Devices Reports > Inventory > Management Status > Unreachable Devices	This report displays all the unreachable devices.

Mapping CM Reports and Terminologies in Reports

Table 9-14 Mapping RME Features and Terminologies in Admin

CM Reports	Name of the report in LMS 4.2	Description
Custom Reports	Custom Reportsl Reports > Report Designer > User Tracking > Custom Reports	You can customize the layout and columns displayed in the reports to suit your needs.
Custom Layouts	Custom Layouts Reports > Report Designer > User Tracking > Custom Layouts	You can create or customize the columns displayed in Custom Reports using Custom Layouts option.
User Tracking Reports	Domain Name Display Admin > Network > Display Settings > Domain Name Display	You can specify the way in which domain names are to be displayed in User Tracking Reports, using the Domain Name Display option.
Admin Reports	System reports Reports > System > ANI Server Analysis Reports > System > Data Collection Metrics Reports > System > Device Support	You can view an analysis of the ANI Server, details of devices discovered, Data Collection metrics, and list of devices supported.
Mac Tracking Reports	All Host Entries Reports > Inventory > User Tracking > All Host Entries	Displays the User Tracking Report Generator from you can generate All Host Entries report.
Switch Port Reports	Reports > Switch Port > Ports > Port Attributes	Displays Port Attributes Report. The report gives complete information about the ports in the devices such as Port Name, type, Speed and Duplex mode.
Discrepancies Reports	Discrepancies Reports > Fault and Event > Best Practices > Discrepancies	Displays discrepancies or anomalies in the discovered network. You can generate a report on the discrepancies.
VLAN Reports	VLAN Reports Reports > Technology > VLAN	Displays VLAN reports for devices, switch clouds, or VTP domains. You must select a VTP domain or a switch cloud for generating the report.
VRF Reports	VRF-Lite Reports > Technology > VRF Lite > VRF Lite	View the details of the VRF Supported devices, VRF Capable devices and other devices in your network. You can also generate VRF Reports that includes Device Based VRF report and VRF Based Report
Readiness Reports	Readiness Reports > Technology > VRF Lite > Readiness	The Readiness Report provides the VRF readiness of the devices in the network. The Readiness Report provides information of the VRF Supported and VRF Capable devices.

Mapping HUM Reports and Terminologies in Reports

Table 9-15 Mapping RME Features and Terminologies in Admin

HUM Reports	Name of the report in LMS 4.2	Description
Quick Reports	Device Reports Reports > Performance > Device > CPU Utilization Reports > Performance > Device > Device Performance Reports > Performance > Device > Availability Reports > Performance > Device > Memory Utilization Interface Reports Reports > Performance > Interface > Availability Reports > Performance > Interface > Error Rate Reports > Performance > Interface > Utilization PoE Port Utilization Reports > Technology > PoE > PoE Port Utilization PSE Consumtion Reports > Technology > PoE > PSE Consumption	Cisco Prime LMS 4.2 contains a set of predefined system generated reports called Device Reports and Interface Reports. These reports run periodically and are stored in the server. These Reports provide detailed information about the devices polled. The Reports page provides information only on the Top-10 and Bottom-10 devices. The Top-10 and Bottom-10 devices are devices that have the highest or lowest utilization or availability value. POE Port Utilization report displays the port level utilization for each device polled for the Power Over Ethernet Port Utilization template. PSE Consumption displays the power utilization and losses for each device polled for the Power Over Ethernet PSE Consumption template.
Poller Reports	Poller Reports Reports > Performance > Poller	You to create Poller Reports based on the template added in a given Poller.
Threshold Violation Reports	Threshold Violation Reports Reports > Fault and Event > Threshold Violation > Thresholds.	This report displays the Threshold Violations details for each device based on the polled data
TrendWatch Report	TrendWatch Report Reports > Fault and Event > Threshold Violation > Trendwatch Details	You allows you to create reports based on each TrendWatch configured for the MIB variable
Trendwatch Summary Reports	Trendwatch Summary Reports > Fault and Event > Threshold Violation > Trendwatch Summary	You can create consolidated reports based on the TrendWatches configured for the MIB variable

Mapping DFM Reports and Terminologies in Reports

Table 9-16 Mapping RME Features and Terminologies in Admin

DFM Reports	Name of the report in LMS 4.2	Description
Group/Device Filtering	Device Fault Reports > Fault and Event > History > Device Fault	You can use the Group/Device Filtering option to get information about the alerts and events that occur on a specific device or device group.
Alert/Event ID Filtering	Event History Reports > Fault and Event > History > Event History	You can use the Alert/Event ID Filtering option to get information about all instances of alerts and events that occur in your network.

Mapping IPM Reports and Terminologies in Reports

Table 9-17 Mapping RME Features and Terminologies in Admin

IPM Reports	Name of the report in LMS 4.2	Description
Report Archives	Report Archives Reports > Report Archives > IPSLA	You can manage the archived reports and create report jobs.
Audit Reports	IPSLA Audit Reports > Audit > IPSLA	You can generate audit reports on all Audit changes that occurred in the network during a specified time period.
System Reports	IPSLA System Summary Reports > Performance > IPSLA System Summary > Daily	You can generate system reports automatically for all collectors based on the report types and granularity after the consolidation of the statistical data. The system reports generated are in tabular format.
IPSLA Reports	IPSLA Detailed Reports > Performance > IPSLA Detailed	You can generate the following statistical reports and graphs based on the granularity (such as Minute, Hourly, Daily, Weekly, Monthly).
Summarized Reports	IPSLA Summary Reports > Performance > IPSLA Summary	You can generate portlet reports in LMS 4.2. Scheduling and generating e-mail notification will be provided for these reports.

Mapping LMS 3.2 Features in Admin

Admin function in Cisco Prime LAN Management Solution (LMS) 4.2 groups all the activities and tasks that a user with Network or System Administrator privileges needs to perform.

Admin function allows you to:

•Prevent unauthenticated access to LMS server, Cisco Prime applications, and data.

•Manage security while operating in single-server and multi-server modes

•Manage process, set up backup parameters, update licensing information, collect server information, manage jobs and resources, and configure system-wide information on the Cisco Prime Server

•Configure discovery settings, and perform administrative tasks in Device and Credential Repository

•Combine the device grouping for various LMS functionalities with a consolidated attribute list.

•Modify SNMP Timeouts and Retries, schedule Data Collection. and configure Polling options.

•Locate and track end hosts in your network to troubleshoot and analyze any connectivity issues.

•Administer Collection Settings

•Perform administrative tasks that are required to monitor and troubleshoot your network using LMS

•Perform administrative tasks involved in setting up notification, syslog settings.

•Customize the names and event severity, create and activate notification subscriptions, and setup up automated actions for Change Audit tasks and syslogs

•Administer Change Audit and Software Management

•Configure Job Policies, approve, and reject jobs

•Check for software and device support updates, download them to their server file system along with the related dependent packages, and install the device updates.

•View and interpret the discrepancies and best practices deviations in your network.

•Administer report and purge settings

•Set the debugging settings of various modules in LMS.

Features in Admin function are derived from the following LMS 3.2 applications:

•CiscoWorks Resource Manager Essentials (RME), see Mapping RME Features and Terminologies in Admin.

•CiscoWorks Common Services (CS), see Mapping CS Features and Terminologies in Admin.

•CiscoWorks Campus Manager (CM), see Mapping CM Features and Terminologies in Admin.

•CiscoWorks Health and Utilization Monitor (HUM), see Mapping HUM Features and Terminologies in Admin.

•CiscoWorks Device Fault Manager (DFM), see Mapping DFM Features and Terminologies in Admin.

•CiscoWorks Internetwork Performance Monitor (IPM), see Mapping IPM Features and Terminologies in Admin.

See Administration of Cisco Prime LAN Management Solution 4.2 for more information.

Mapping RME Features and Terminologies in Admin

This section provides information on the RME features and terminologies mapped to Admin function in LMS 4.2.

Table 9-18 Mapping RME Features and Terminologies in Admin

RME Features	Admin Function	Description
Group Administration	Group Management (Admin > System: Group Management) The Group Management function is also available under Inventory (Inventory > Group Management)	Group Management feature in Admin allows you to perform: •Device •Fault •IPSLA Collector •Port and Module
Change Audit	Change Audit Settings (Admin > Network: Change Audit Settings)	Change Audit Settings feature in Admin allows you to perform: •Inventory Change Filter •Config Change Filter •Exception Periods
Syslog Collector Status	Syslog Collector Status (Admin > Collection Settings: Syslog > Syslog Collector Status)	Syslog Collector Status feature in Admin allows you to: •View the status of your Common Syslog Collector •Subscribe/Unsubscribe a Common Syslog Collector •Test Syslog Collector Subscription •Understand the Syslog Collector Properties File
Automated Actions	Syslog Automated Actions (Admin > Network: Notification and Action Settings > Syslog Automated Actions)	Syslog Automated Actions feature in Admin allows you to: •Create an Automated Action •Edit an Automated Action •Write Automated Script •Enable or Disable an Automated Action •Exporte or Importe an Automated Action •Delete an Automated Action
Message Filters	Syslog Message Filters (Admin > Network: Notification and Action Settings > Syslog Message Filters)	Syslog Message Filters feature in Admin allows you to: •Create a Filter •Edit a Filter •Enable or Disable a Filter •Export or Import a Filter •Delete a Filter
Force Purge	ChangeAudit Force Purge (Admin > Network: Purge Settings > ChangeAudit Force Purge)	ChangeAudit Force Purge feature allows you to perform a Forced Purge of Change Audit, as required
Config Change Filter	Config Change Filter (Admin > Network: Change Audit Settings > Config Change Filter)	Config Change Filter feature allows you to enable or disable VLAN Change audit filtering.
Transport Settings	Config Transport Settings (Admin > Collection Settings: Config > Config Transport Settings)	Config Transport Settings feature allows you to set the protocol order for Configuration Management features such as Archive Management, Config Editor, and NetConfig jobs to download configurations and to fetch configurations.
Archive Mgmt	Config Archive Settings (Admin > Collection Settings: Config > Config Archive Settings)	Config Archive Settings feature allows you to move the directory where the configuration of the devices can be archived on the LMS server.
Archive Settings	Config Archive Settings (Admin > Collection Settings: Config > Config Archive Settings)	Config Archive Settings feature allows you to move the directory where the configuration of the devices can be archived on the LMS server.
Collection Settings	Config Collection Settings (Admin > Collection Settings: Config > Config Collection Settings)	Config Collection Settings feature allows you to define the configuration collection settings
Purge Settings	Config Archive Purge Settings (Admin > Network: Purge Settings > Config Archive Purge Settings)	Config Archive Purge Settings feature allows you to Purge Configurations from the Configuration Archive
Exclude Settings	Config compare Exclude Commands Configuration (Admin > Collection Settings: Config > Config compare Exclude Commands Configuration)	Config compare Exclude Commands Configuration feature allows you to list the commands that have to be excluded while comparing configuration
Fetch Settings	Config Job Timeout Settings (Admin > Collection Settings: Config > Config Job Timeout Settings)	Config Job Timeout Settings feature allows you to configure the Job Result Wait Time per device for the Sync Archive Jobs.
Config Job Policies	Config Job Policies (Admin > Network: Configuration Job Settings > Config Job Policies)	Config Job Policies feature allows you to define the default job policies for Configuration Management applications like NetConfig, ArchiveMgmt, ConfigEditor, Netshow
CDA Settings	Verification Settings (Admin > Network: Device Credential Settings > Verification Settings)	Verification Settings feature allows you to verify Device Credentials
Inventory	Inventory (Admin > Collection Settings: Inventory)	Inventory feature in Admin allows you to create and manage inventory jobs
Inventory Change Filter	Inventory Change Filter (Admin > Network: Change Audit Settings > Inventory Change Filter)	Inventory Change Filter feature allows you to select the attributes that you do not wish to log using Change Audit
System Job Schedule	Inventory System Job Schedule (Admin > Collection Settings: Inventory > Inventory System Job Schedule)	Inventory System Job Schedule feature allows you to change the schedule of default, periodic system jobs
PSIRT/EOX Reports	PSIRT/EOX reports option (Admin > Network: PSIRT, EOS and EOL Settings > PSIRT/EOX reports option)	PSIRT/EOX reports option feature allows you to change the data source for generating a PSIRT or End-of-Sale or End-of-Life report.
Software Mgmt	Software Image Management (Admin > Network: Software Image Management)	Software Image Management feature allows you to View/Edit Preferences
Set Backup Policy	Syslog Backup Settings (Admin > Network: Purge Settings > Syslog Backup Settings)	Syslog Backup Settings feature allows you to set up the Syslog backup policy
Set Purge Policy	Syslog Purge Settings (Admin > Network: Purge Settings > Syslog Purge Settings)	Syslog Purge Settings feature allows you to specify a default policy for the periodic purging of Syslog messages.
Force Purge	Syslog Force Purge (Admin > Network: Purge Settings > Syslog Force Purge)	Syslog Force Purge feature allows you to perform a forced purge of Syslog messages, as required.

Mapping CS Features and Terminologies in Admin

This section provides information on the CS features and terminologies mapped to Admin function in LMS 4.2.

Table 9-19 Mapping CS Features in Admin

CS Features	Admin Function	Description
Server	Server Monitoring (Admin > System: Server Monitoring)	The Server Monitoring feature allows you to: •Collect Server Information •DiskWatcher Configuration •Processes •Selftest
Single-Server Management	Single-Server Management (Admin > Trust Management: Local Server > Single-Server Management)	Single-Server Management feature allows you to view the mode of server security and the information on self signed certificate.
Browser-Server Security Mode Setup	Browser-Server Security Mode Setup (Admin > Trust Management: Local Server > Browser-Server Security Mode Setup)	Browser-Server Security Mode Setup feature allows you to enable or disable the Browser Server Security
Local User Policy Setup	Local User Policy Setup (Admin > System: User Management > Local User Policy Setup)	Local User Policy Setup feature allows you to setup username and password policies for CiscoWorks local users in LMS
Local User Setup	Local User Setup (Admin > System: User Management > Local User Setup)	Local User Setup feature allows you to: •Import users •Export users •Modify your profile •Add a local user •Edit user profiles •Delete local users
Certificate Setup	Certificate Setup (Admin > Trust Management: Local Server > Certificate Setup)	Certificate Setup feature allows you to create security certificates that enable SSL communication between your client browser and management server.
Multi-Server Trust Management	Multi Server (Admin > Trust Management: Multi Server)	You can configure the following in Multi-Server mode: •Peer Server Account Setup •System Identity Setup •Peer Server Certificate Setup •Single Sign-On Setup
Peer Server Account Setup	Peer Server Account Setup (Admin > Trust Management: Multi Server > Peer Server Account Setup)	Peer Server Account Setup feature allows you to create users who can login to CiscoWorks Servers and perform certain tasks.
System Identity Setup	System Identity Setup (Admin > Trust Management: Multi Server > System Identity Setup)	System Identity Setup feature allows you to create a trust user on servers that are part of a multi-server setup.
Peer Server Certificate Setup	Peer Server Certificate Setup (Admin > Trust Management: Multi Server > Peer Server Certificate Setup)	Peer Server Certificate Setup feature allows you to add certificates of any number of peer CiscoWorks Servers to the trusted store of each server.
Single Sign-On Setup	Single Sign-On Setup (Admin > Trust Management: Multi Server > Single Sign-On Setup)	Single Sign-On Setup feature allows you to use your browser session to transparently navigate to multiple CiscoWorks Servers without authenticating to each of them.
Authentication Mode Setup	Authentication Mode Setup (Admin > System: Authentication Mode Setup)	Authentication Mode Setup feature allows you to select login modules and set their options.
Cisco.com Connection Management	Connection Management (Admin > System: Cisco.com Settings > Connection Management)	Connection Management feature allows you to view the Cisco.com Connection Details
Cisco.com User Account Setup	User Account Setup (Admin > System: Cisco.com Settings > User Account Setup)	User Account Setup feature allows you to add and modify Cisco.com user login names and password.
Proxy Server Setup	Proxy Server Setup (Admin > System: Cisco.com Settings > Proxy Server Setup)	Proxy Server Setup feature allows you to update the proxy server configuration.
Processes	Processes (Admin > System: Server Monitoring > Processes)	Processes feature allows you to: •View the details of all processes •Filter and show only processes of a specific state •Start the processes •Stop the processes
Backup	Backup (Admin > System: Backup)	Backup feature allows you to schedule immediate, daily, weekly, or monthly automatic database backups.
Log Rotation	Log Rotation (Admin > System: Log Rotation)	Log Rotation feature allows you manage the log files more efficiently.
Licensing	License Management (Admin > System: License Management)	License Management feature allows you to: •Obtain a License for CiscoWorks LMS •License the Application •View License Information •Update Licenses
Collect Server Information	Collect Server Information (Admin > System: Server Monitoring > Collect Server Information)	Collect Server Information feature helps you to get the following server information: •System information •Environment •Configuration •Logs •Web server information •Device and credentials administration information •Grouping services information
Selftest	Selftest (Admin > System: Server Monitoring > Selftest)	Selftest feature allows you to •View self test reports •Test certain basic functions of the server.
Notify Users	Notify Users (Admin > System: User Management > Notify Users)	Notify Users feature allows you to broadcast messages to online users.
Job Browser	Browser (Admin > Jobs: Browser)	Browser feature allows you to view the status of all the LMS admin-related Jobs.
Resource Browser	Resource Browser (Admin > Network: Resource Browser)	Resource Browser feature allows you to: •View Resource details •Free locked resources
System Preferences	System Preferences (Admin > System: System Preferences)	System Preferences feature allows you to configure system-wide information on the CiscoWorks Server
Common Services Log Configurations	Common Services Log Configurations (Admin > System: Debug Settings > Common Services Log Configurations)	Common Services Log Configurations feature allows you to enable the debugging option for the Common Services components.
DiskWatcher Configuration	DiskWatcher Configuration (Admin > System: Server Monitoring > DiskWatcher Configuration)	DiskWatcher Configuration feature allows you to calculate the disk space information of a drive (on Windows) or a file system (on Solaris) where CiscoWorks LMS is installed, and stores them in diskWatcher.log file.
Groups	Group Management (Admin > System: Group Management) The Group Management function is also available under Inventory (Inventory > Group Management)	Group Management feature allows you to perform: •Device •Fault •IPSLA Collector •Port and Module
Software Center	Software Center (Admin > System: Software Center)	Software Center feature allows you to check for software and device support updates, download them to their server file system along with the related dependent packages, and install the device updates.
Software Update	Software Update (Admin > System: Software Center > Software Update)	Software Update feature allows you to: •Select Software Updates •Download Software Updates
Device Update	Device Update (Admin > System: Software Center > Device Update)	Device Update feature allows you to: •View a list of all CiscoWorks related devices packages on your system •Check for the device updates •Delete the device packages
Schedule Device Downloads	Schedule Device Downloads (Admin > System: Software Center > Schedule Device Downloads)	Schedule Device Downloads feature allows you to: •Schedule device package downloads and specify the time, frequency of the downloads. •Specify download policies.
Activity Log	Activity Log (Admin > System: Software Center > Activity Log)	The Activity Log page displays the following: •Scheduled Job Details: This page displays the details of scheduled jobs in the software center. •Event Log: This page displays the logs of events in the software center.
Device Selector Settings	Device Selector Settings (Admin > Network: Display Settings > Device Selector Settings)	The Device Selector Settings section contains the following features. These settings are stored on a per-user basis. •Group Customization: Provides options to select/remove the Device Selector groups. •Group Ordering: Provides options to select/remove the groups to be displayed in the device selectors.
Mode Settings	Mode Settings (Admin > Network: Device Credential Settings > Mode Settings)	Mode Settings feature allows you to change the current mode.
Device Polling	Device Polling (Admin > Network: Device Credential Settings > Device Polling)	Device Polling feature allows you to: •Activate Device Polling to check whether the devices can be reached •Configure Device Polling policy •Schedule Device Polling •Display a list of devices that are not reachable for a certain period of time •Delete the selected unreachable devices from DCR
Device Poll Settings	Device Poll Settings (Admin > Network: Device Credential Settings > Device Poll Settings)	Device Poll Settings feature allows you to configure a Device Polling policy and schedule a Device Polling job to check whether the devices can be reached.
User Defined Fields	User Defined Fields (Admin > Network: Device Credential Settings > User Defined Fields)	User Defined Fields feature allows you to: •Add User Defined Fields •Rename User Defined Fields •Delete User Defined Fields
Default Credential Sets	Default Credential Sets (Admin > Network: Device Credential Settings > Default Credential Sets)	Default Credential Sets feature allows you to: •Configuring a Default Credentials Set •Deleting a Default Credentials Set
Default Credential Sets Policy Configuration	Default Credential Sets Policy Configuration (Admin > Network: Device Credential Settings > Default Credential Sets Policy Configuration)	Default Credential Sets Policy Configuration feature allows you to configure default credential set policies and apply the default credentials for a range of devices to be added or imported to DCR.

Mapping CM Features and Terminologies in Admin

This section provides information on the CM features and terminologies mapped to Admin function in LMS 4.2.

Table 9-20 Mapping CM Features in Admin

CM Features	Admin Function	Description
User Tracking	User Tracking (Admin > Collection Settings: User Tracking)	User Tracking feature allows you to locate and track the end hosts in your network
Acquisition	Acquisitions Info (Admin > Collection Settings: User Tracking > Acquisitions Info)	Acquisitions Info feature allows you to view acquisition information
Acquisition Actions	Acquisition Action (Admin > Collection Settings: User Tracking > Acquisition Action)	Acquisition Action feature allows you to trigger the following acquisitions: •Device based Acquisition •Subnet based Acquisition •IP Phone Acquisition
Acquisition Settings	Acquisition Settings (Admin > Collection Settings: User Tracking > Acquisition Settings)	Acquisition Settings feature allows you to modify User Tracking Acquisition settings
Schedule Acquisition	Acquisition Schedule (Admin > Collection Settings: User Tracking > Acquisition Schedule)	Acquisition Schedule feature allows you to modify UT acquisition schedule
Ping Sweep	Ping Sweep (Admin > Collection Settings: User Tracking > Ping Sweep)	Ping Sweep feature allows you to determine the range of IP addresses that map to live end hosts (computers).
Configure Subnet Acquistion	Subnet Acquisition Configuration (Admin > Collection Settings: User Tracking > Subnet Acquisition Configuration)	Subnet Acquisition Configuration feature allows you to configure LMS to perform User Tracking Acquisition on selected subnets.
Delete Interval	User Tracking Purge Policy (Admin > Network: Purge Settings > User Tracking Purge Policy)	User Tracking Purge Policy feature allows you to modify the time interval for deleting entries from the End Host Table, IP Phone Table or the History Table from the database.
Configure Trunk for End Hosts Discovery	Acquisition Configuration in Trunk (Admin > Collection Settings: User Tracking > Acquisition Configuration in Trunk)	Normally UT Acquisition discovers end hosts connected only to access ports. If you enable this feature UT Acquisition discovers end hosts connected to non-link trunk ports also.
Reports	Domain Name Display (Admin > Network: Display Settings > Domain Name Display)	Domain Name Display feature allows you to specify the way in which domain names are to be displayed in User Tracking Reports
User Tracking Purge Policy	User Tracking Report Purge Policy (Admin > Network: Purge Settings > User Tracking Report Purge Policy)	User Tracking Report Purge Policy feature allows you specify the intervals at which old reports and jobs are to be purged.
End Host Table Import	Table Import (Admin > Collection Settings: User Tracking > Table Import)	Table Import feature allows you to mport from a file, user names and notes for end hosts already discovered
Dynamic Updates	Dynamic Update Process Status (Admin > Collection Settings: User Tracking > Dynamic Update Process Status)	Dynamic Update Process Status feature allow you to: •Check whether the Dynamic Updates processes are running or not. •Start or Stop dynamic updates
Device Trap Configuration	Device Trap Configuration (Admin > Collection Settings: User Tracking > Device Trap Configuration)	Device Trap Configuration feature allows you to configure the Cisco switches for sending SNMPv1/SNMPv2 MAC Notification Traps when a host is connected to or disconnected from that port.
Trap Listener Configuration	Trap Listener Configuration (Admin > Collection Settings: User Tracking > Trap Listener Configuration)	Trap Listener Configuration feature allows you to configure the trap listener
Dynamic User Tracking Configuration	Dynamic User Tracking Configuration (Admin > Collection Settings: User Tracking > Dynamic User Tracking Configuration)	Dynamic User Tracking Configuration feature allows you configure certain properties in Dynamic User Tracking to enhance the security of the system.
Debugging Options	Dynamic User Tracking (Admin > System: Debug Settings > Dynamic User Tracking)	Dynamic User Tracking feature allows you to set the debugging options required for Dynamic Updates
Dynamic User Tracking Console	Dynamic User Tracking Console (Admin > System: Debug Settings > Dynamic User Tracking Console)	Dynamic User Tracking Console feature allows you to troubleshoot Dynamic User Tracking updates in a detailed way.
User Tracking Reports	User Tracking Reports (Admin > System: Debug Settings > User Tracking Reports)	User Tracking Reports feature allows you to debug events related to User Tracking client side activities
SNMP Timeouts and Retries	Data Collection SNMP Timeouts and Retries (Admin > Collection Settings: Data Collection > Data Collection SNMP Timeouts and Retries)	Data Collection SNMP Timeouts and Retries feature allows you to modify the SNMP timeouts and retries when Data Collection fails for a particular device with SNMP timeout exceptions.
Schedule Data Collection	Data Collection Schedule (Admin > Collection Settings: Data Collection > Data Collection Schedule)	Data Collection Schedule feature allows you to schedule the day and time of data collection
Device Poller	Data Collection Critical Devices Poller (Admin > Collection Settings: Data Collection > Data Collection Critical Devices Poller)	Data Collection Critical Devices Poller feature allows you to: •Configure the time interval at which the network is polled •Poll only a critical set of devices •View the device and link status without running Data Collection
Restricted Topology View	Restricted Topology View (Admin > Network: Monitor / Troubleshoot > Restricted Topology View)	Restricted Topology View feature allows you to view the Restricted Topology
DFM Poller Settings	Fault Poller settings for topology (Admin > Network: Monitor / Troubleshoot > Fault Poller settings for topology)	Fault Poller settings for topology feature allows you to view Fault Poller information in Topology Maps and N-Hop view portlet
Discrepencies	Best Practices Deviation Settings (Admin > Network: Best Practices Deviation Settings)	Best Practices Deviation Settings feature allows you to: •View Reports on Discrepancies •View Reports on Best Practices Deviations •Acknowledge Discrepancies •Acknowledge Best Practices Deviations •Resolve Discrepancies and Best Practices Deviations •Customize Discrepancies Reporting
Purge Settings	Layer2 Services Purge Settings (Admin > Network: Purge Settings > Layer2 Services Purge Settings)	Layer2 Services Purge Settings feature allows you to purge Layer2 services jobs or report archives in LMS
Data Collection	Data Collection (Admin > System: Debug Settings > Data Collection)	Data Collection feature allows you to set the trace, and debugging, for Data Collection
Configuration and Reports	Layer2 Configuration and Reports (Admin > System: Debug Settings > Layer2 Configuration and Reports)	Layer2 Configuration and Reports feature allows you to set up Debugging Options for Network Reports
Topology	Topology (Admin > System: Debug Settings > Topology)	Topology feature allows you to enable debugging for Topology Services client side activities.
User Tracking Server	User Tracking Server (Admin > System: Debug Settings > User Tracking Server)	User Tracking Server feature allows you to debug events related to all User Tracking server side processes
User Tracking Reports	User Tracking Reports (Admin > System: Debug Settings > User Tracking Reports)	User Tracking Reports feature allows you to debug events related to User Tracking client side activities
Dynamic User Tracking	Dynamic User Tracking (Admin > System: Debug Settings > Dynamic User Tracking)	Dynamic User Tracking feature allows you to set the debugging options required for Dynamic Updates
RMON Configuration	RMON Configuration (Admin > Network: Monitor / Troubleshoot > RMON Configuration)	RMON Configuration feature allows you to enable RMON to Measure Bandwidth Utilization
VRF Collector Schedule	VRF Lite Collector Schedule (Admin > Collection Settings: VRF Lite > VRF Lite Collector Schedule)	VRF Lite Collector Schedule feature allows you to: •Schedule the day and the time of VRF Lite Collection •Add a new schedule, edit or delete existing schedules
VRF SNMP Timeouts and Retries	VRF Lite SNMP Timeouts and Retries (Admin > Collection Settings: VRF Lite > VRF Lite SNMP Timeouts and Retries)	VRF Lite SNMP Timeouts and Retries feature allows you to modify the SNMP timeouts and retries when VRF Lite Collection fails for a particular device with SNMP timeout exceptions.
VNM Purge Settings	VRF Lite Purge Settings (Admin > Network: Purge Settings > VRF Lite Purge Settings)	VRF Lite Purge Settings feature allows you to purge VRF Management jobs or report archives in LMS.
Debugging Options	VRF Lite Server Debugging (Admin > System: Debug Settings > VRF Lite Server Debugging)	VRF Lite Server Debugging feature allows you to set an Application Logging Level to VRF Lite Server details.
VNM Server Debugging	VRF Lite Server Debugging (Admin > System: Debug Settings > VRF Lite Server Debugging)	VRF Lite Server Debugging feature allows you to o set an Application Logging Level to VRF Lite Server details.
VNM Collector Debugging	VRF Lite Collector Debugging (Admin > System: Debug Settings > VRF Lite Collector Debugging)	VRF Lite Collector Debugging feature allows you to set an Application Logging Level to VRF Collector details.
VNM Client Debugging	VRF Lite Client Debugging (Admin > System: Debug Settings > VRF Lite Client Debugging)	VRF Lite Client Debugging feature allows you to set an Application Logging Level to VRF Lite Client
VNM Utility Debugging	VRF Lite Utility Debugging (Admin > System: Debug Settings > VRF Lite Utility Debugging)	VRF Lite Utility Debugging feature allows you to set an Application Logging Level to VRF Lite Utility

Mapping HUM Features and Terminologies in Admin

This section provides information on the HUM features and terminologies mapped to Admin function in LMS 4.2.

Table 9-21 Mapping HUM Features in Admin

HUM Features	Admin Function	Description
Data Purge	Performance data purge settings (Admin > Network: Purge Settings > Performance data purge settings)	Performance data purge settings feature allows you to: •Periodically purge polled data that you no longer need in the database. •Purge data records such as summarization records, Poller failure records, threshold violation records, audit trail records.
Job Purge	Performance Job Purge Settings (Admin > Network: Purge Settings > Performance Job Purge Settings)	Performance Job Purge Settings feature allows you to periodically purge job data that you no longer need.
Load MIB	Load MIB (Admin > Network: Monitor / Troubleshoot > Load MIB)	Load MIB feature allows you to load a new MIB file into LMS
Log Level Settings	Performance Debugging Settings (Admin > System: Debug Settings > Performance Debugging Settings)	Performance Debugging Settings allows you to configure and manage log level settings in Device Performance Management function of LMS.
Poll Settings	Performance Management SNMP timeouts and retry settings (Admin > Collection Settings: Performance > Performance Management SNMP timeouts and retry settings)	Performance Management SNMP timeouts and retry settings feature allows you to configure the Performance Management SNMP timeout and SNMP retries
Purge Details	Performance Data Purge Summary (Admin > Network: Purge Settings > Performance Data Purge Summary)	Performance Data Purge Summary feature allows you to view the details of the data purged
Syslog Receiver Groups	Performance - Syslog notification (Admin > Network: Notification and Action Settings > Performance - Syslog notification)	Performance - Syslog notification feature allows you to create Syslog Receiver Groups
Trap Receiver Groups	Performance - SNMP Trap notification (Admin > Network: Notification and Action Settings > Performance - SNMP Trap notification)	Performance - SNMP Trap notification feature allows you to create SNMP Trap Receiver Groups

Mapping DFM Features and Terminologies in Admin

This section provides information on the DFM features and terminologies mapped to Admin function in LMS 4.2.

Table 9-22 Mapping DFM Features in Admin

DFM Features	Admin Function	Description
Daily Purging Schedule	Fault History Purging Schedule (Admin > Network: Purge Settings > Fault History Purging Schedule)	Fault History Purging Schedule feature allows you to configure the Daily Fault History Purging Schedule
Group Administration	Group Management (Admin > System: Group Management) The Group Management function is also available under Inventory (Inventory > Group Management)	Group Management feature in Admin allows you to perform: •Device •Fault •IPSLA Collector •Port and Module
Logging	Fault Debugging Settings (Admin > System: Debug Settings > Fault Debugging Settings)	Fault Debugging Settings feature allows you to set the Fault Management debug settings
Rediscovery Schedule	Fault Management Rediscovery Schedule (Admin > Collection Settings: Fault > Fault Management Rediscovery Schedule)	Fault Management Rediscovery Schedule feature allows you to: •Suspend and Resume a Rediscovery Schedule •Add and Modify a Rediscovery Schedule
SNMP Trap Forwarding	Fault - SNMP trap forwarding (Admin > Network: Notification and Action Settings > Fault - SNMP trap forwarding)	Fault - SNMP trap forwarding feature allows you to configure SNMP Trap Forwarding
SNMP Trap Receiving	Fault - SNMP trap receiving settings (Admin > Network: Notification and Action Settings > Fault - SNMP trap receiving settings)	Fault - SNMP trap receiving settings feature allows you to update the SNMP Trap Receiving Port
SNMP Default Server	SMTP Default Server (Admin > System: SMTP Default Server)	SMTP Default Server feature allows you to configure a Default SMTP Server
Event Sets	Event Sets (Admin > Network: Notification and Action Settings > Event Sets)	Event Sets feature allows you to configure Event Sets
E-mail Notification	Fault - Email notification (Admin > Network: Notification and Action Settings > Fault - Email notification)	Fault - Email notification feature allows you to manage Fault E-Mail Notification Subscriptions
E-mail Subject Customization	Fault - Email subject customization (Admin > Network: Notification and Action Settings > Fault - Email subject customization)	Fault - Email subject customization feature allows you to customize the e-mail subject for forwarded events.
Notification Customization	Fault Notification Customization (Admin > Network: Notification and Action Settings > Fault Notification Customization)	Fault Notification Customization feature allows you to customize the names and event severity in LMS
Notification Groups	Fault Notification Group (Admin > Network: Notification and Action Settings > Fault Notification Group)	Fault Notification Group feature allows you to configure Fault Notification Groups
Syslog Notification	Fault - Syslog notification (Admin > Network: Notification and Action Settings > Fault - Syslog notification)	Fault - Syslog notification feature allows you to manage Fault Syslog Notifications
SNMP Config	Fault Management SNMP Timeouts and Retries (Admin > Collection Settings: Fault > Fault Management SNMP Timeouts and Retries)	Fault Management SNMP Timeouts and Retries feature allows you to modify Fault Management SNMP Timeout and Retries

Mapping IPM Features and Terminologies in Admin

This section provides information on the IPM features and terminologies mapped to Admin function in LMS 4.2.

Table 9-23 Mapping IPM Features in Admin

IPM Features	Admin Function	Description
Application Settings	IPSLA application settings (Admin > Collection Settings: Performance > IPSLA application settings)	IPSLA application settings feature allows you to copy IPSLA (Internet Protocol Service Level Agreement) configuration to running-config, and set managed source interface.
Syslog Configuration	IPSLA Syslog Configuration (Admin > Network: Notification and Action Settings > IPSLA Syslog Configuration)	IPSLA Syslog Configuration feature allows you to enable or disable the IPSLA Syslog
Log Level Settings	IPSLA Debugging Settings (Admin > System: Debug Settings > IPSLA Debugging Settings)	IPSLA Debugging Settings feature allows you to set the log levels for IPSLA Performance Management
Purge Settings	IPSLA data Purge Settings (Admin > Network: Purge Settings > IPSLA data Purge Settings)	IPSLA data Purge Settings feature allows you to set the Purge period for Historical and Audit reports. You can also set the Purge period from the Setup Center.
Group Admin	Group Management (Admin > System: Group Management) The Group Management function is also available under Inventory (Inventory > Group Management)	Group Management feature in Admin allows you to perform: •Device •Fault •IPSLA Collector •Port and Module