Examples

The following is sample output from the show metadata application table command:

Router# show metadata application table

ID     Name                  Vendor      Version   
--------------------------------------------------------------------------------
218103921  telepresence-media    -           -         
218103922  telepresence-contr$   -           -         
218104286  telepresence-data     -           -         
218104220  webex-voice           -           -         
218104221  webex-video           -           -         
218104222  webex-meeting         -           -         
218103864  citrix                -           -         
218103889  cisco-phone           -           -         
218104284  vmware-view           -           -         
218104281  wyze-zero-client      -           -         
218103869  rtp                   -           -         
218103872  h323                  -           -         
218108868  sip                   -           -         
218104362  rtsp                  -           -         
      

The table below describes the significant fields shown in the display.

Examples

The following is sample output from the show metadata flow classification table command:

Router# show metadata flow classification table

Target          Flow ID    Dir   Policy          Class           Type       Value                    

Et0/0           3          IN/CL                                                                    
Et0/0           4          IN/CL                                                                    
Et0/1           3          OUT                                                                      
Et0/1           4          OUT                                                                      
      

Table below describes the significant fields shown in the display.

The following is sample output from the show metadata flow local-flow-id command:

Router# show metadata flow local-flow-id 1

To               From            Protocol  SPort   DPort    Ingress I/F        Egress I/F               
10.6.6.6         10.4.4.4         UDP      1000    1000     Ethernet0/0        Ethernet0/1             

Metadata Attributes :

Application Tag             :   218103921 (telepresence-media)
Application Name            :   telepresence-media

Table below describes the significant fields shown in the display.

The following is sample output from the show metadata flow statistics command:

Router# show metadata flow statistics

Interface specific report :

Ethernet0/0: Ingress flows 0, Egress flows 0
Ethernet0/1: Ingress flows 0, Egress flows 0

Chunk statistics: 

Type               Allocated       Returned        Failed         

IPV4 Flow           0                0                0              
Flow Key            3                1                0              
Source List         1                0                0              
Flow Info           3                3                0              
Attribute Data      3                3                0              
Feature Object      0                0                0              

Event Statistics: 

Add Flow                 : 2         Delete Flow              : 0       
Recieved                 : 3         Rejected                 : 0       
Transient                : 0         Posted                   : 3       
Ingress Change           : 0         Egress Change            : 0       
Unkown                   : 0         Source Limit Exceeded    : 0       

Table below describes the significant fields shown in the display.

The following is sample output from the show metadata flow table command.

The table above describes the significant fields shown in the display.

Router# show metadata flow table

Flow ID    To               From             Protocol DPort SPort Ingress I/F    Egress I/F     

1          10.6.6.6         10.4.4.4         UDP      1000  1000  Et0/0          Et0/1         
2          10.6.6.6         10.4.4.4         UDP      1001  1001  Et0/0          Et0/1 

The following is sample output from the show metadata flow table filter command. You can specify the source or destination IPv4 address as the filter criteria.

The table above describes the significant fields shown in the display.

Router# show metadata flow table filter destination 10.6.6.6

Entries To: 10.6.6.6         

Flow ID    From             Protocol DPort   SPort   Ingress I/F    Egress I/F     
1          10.4.4.4         UDP      1000    1000    Et0/0          Et0/1         
2          10.4.4.4         UDP      1001    1001    Et0/0          Et0/1         
Total Flows: 2

Examples

Last Logged Packet Example

This example shows how to display information about the last logged packet:

Router# show mls qos last
QoS engine last packet information:
    Packet was transmitted
    Output TOS/DSCP: 0xC0/48[unchanged]   Output COS: 0[unchanged]
    Aggregate policer index: 0(none)
    Microflow policer index: 0(none)                                 

IPv6 Example

This example shows how to display IPv6 information:

Router# show mls qos ipv6
QoS Summary [IPv6]:      (* - shared aggregates, Mod - switch module)
     Int Mod Dir  Class-map DSCP  Agg  Trust Fl   AgForward-By   AgPoliced-By
                                  Id         Id
------------------------------------------------------------------------------
      All  7   -    Default    0    0*    No  0      189115356              0

Example

This example shows how to display QoS information:

Router# show mls qos
QoS is enabled globally
Microflow policing is enabled globally
QoS ip packet dscp rewrite enabled globally
QoS is disabled on the following interfaces:
Fa6/3 Fa6/4
QoS DSCP-mutation map is enabled on the following interfaces:
Fa6/5
Vlan or Portchannel(Multi-Earl) policies supported: Yes
Egress policies supported: Yes
----- Module [5] -----
QoS global counters:
Total packets: 164
IP shortcut packets: 0
Packets dropped by policing: 0
IP packets with TOS changed by policing: 0
IP packets with COS changed by policing: 0
Non-IP packets with COS changed by policing: 0
MPLS packets with EXP changed by policing: 0

Example

This example shows the output if you do not enter any keywords:

Router# show mls qos
  QoS is enabled globally
  Microflow QoS is enabled globally
QoS global counters:
    Total packets: 217500
    IP shortcut packets: 344
    Packets dropped by policing: 344
    IP packets with TOS changed by policing 18323
    IP packets with COS changed by policing 1602
    Non-IP packets with COS changed by policing 0

Catalyst 6500 Series Switches Example

The showmlsqos command output in Cisco IOS Release 12.2(33)SXI and later releases contains more packet counter information than in previous releases.

This example shows the Cisco IOS Release 12.2(33)SXI output with the detailed keyword:

Router# show mls qos detailed
  QoS is enabled globally
  Policy marking depends on port_trust
  QoS ip packet dscp rewrite enabled globally
  Input mode for GRE Tunnel is Pipe mode
  Input mode for MPLS is Pipe mode
  Vlan or Portchannel(Multi-Earl) policies supported: Yes
  Egress policies supported: Yes
 ----- Module [5] -----
Traffic:            Total pkt's   30-s pkt's    peak pkts  5-min avg pps   peak pps
-----------------------------------------------------------------------------------
Total packets:           775606           46           22              2          5
IP shortcut packets:     5465402          33           16              1          1
Packets dropped by 
policing:                      0           0            0              0          0
IP packets with TOS 
changed by policing:          41          10            4              0          0
IP packets with COS 
changed by policing:           2           0            0              0          0
Non-IP packets with COS 
changed by policing:           0           0            0              0          0
MPLS packets with EXP 
changed by policing:           0           0            0              0          0

The table below describes the significant fields added when you enter the detailed keyword.

Examples

This example shows how to display information about the aggregate policer for MLS QoS:

Router# show mls qos aggregate-policer
ag1 (undefined)
    AgId=0 [ pol1 pol2 ]
ag2 64000 64000 conform-action set-dscp-transmit 56 exceed-action drop
    AgId=0 [ pol3 ]
ag3 32000 32000 conform-action set-dscp-transmit 34 exceed-action drop

In the output, the following applies:

• The AgId parameter displays the hardware-policer ID and is nonzero if assigned.
• The policy maps using the policer, if any, are listed in the square brackets ([]).
• If there are no policies using the policer, no AgId line is displayed.
• If the policer is referred to in policy maps, but has not been defined, [undefined] is displayed.

Examples

This example shows how to display the number of free aggregate RAM indexes on the switch processor and the DFCs:

Router# show mls qos free-agram 
Total Number of Available AG RAM indices : 1023
 Module [1]
 Free AGIDs : 1023
 Module [6]
 Free AGIDs : 1023

Examples

The following is sample output from the showmlsqosinterfacefastethernet0/1command:

Router# show mls qos interface fastethernet0/1
FastEthernet0/1
trust state: trust cos
COS override: dis
default COS: 0

The following example shows that there is no mls QoS command configured on the interface. the CoS/IP Precidence/DSCP values of incoming traffic will not be remarked as it passes through the switch.

Router# show mls qos interface f1/1
FastEthernet1/1
trust state: none  <<<
trust mode: none  <<<
COS override: dis
default COS: 0
pass-through: none

Examples

The following is sample output from the showmlsqosmapscos-dscp command displaying the DSCP values to which each CoS value will be mapped:

Router# show mls qos maps cos-dscp
Cos-dscp map:
        cos:  0  1  2  3  4  5  6  7
     --------------------------------
       dscp:  8  8  8  8 24 32 56 56

The following is sample output from the showmlsqosmapsdscp-cos command displaying the CoS values to which each DSCP value will be mapped:

Router# show mls qos maps dscp-cos
Dscp-cos map:
       dscp:  0  8 10 16 18 24 26 32 34 40 46 48 56
     -----------------------------------------------
        cos:  0  1  1  1  2  2  3  3  4  4  5  6  7

This example shows how to display the QoS-map settings:

Router# show mls qos maps
   Policed-dscp map:
            0  1  2  3  4  5  6  7  8  9
   ----------------------------------
      00:  00 01 02 03 04 05 06 07 08 09
      10:  10 11 12 13 14 15 16 17 18 19
      20:  20 21 22 23 24 25 26 27 28 29
      30:  30 31 32 33 34 35 36 37 38 39
      40:  40 41 42 43 44 45 46 47 48 49
      50:  50 51 52 53 54 55 56 57 58 59
      60:  60 61 62 63
   Dscp-cos map:
            0  1  2  3  4  5  6  7  8  9
   ----------------------------------
      00:  00 00 00 00 00 00 00 00 01 01
      10:  01 01 01 01 01 01 02 02 02 02
      20:  02 02 02 02 03 03 03 03 03 03
      30:  03 03 04 04 04 04 04 04 04 04
      40:  05 05 05 05 05 05 05 05 06 06
      50:  06 06 06 06 06 06 07 07 07 07
      60:  07 07 07 07
   Cos-dscp map:
          cos:   0  1  2  3  4  5  6  7
       ----------------------------------
        dscp:   0  8 16 24 32 40 48 56
   IpPrecedence-dscp map:
       ipprec:   0  1  2  3  4  5  6  7
       ----------------------------------
        dscp:   0  8 16 24 32 40 48 56
Router# 

In the policed DSCP and DSCP-CoS map displays, the new DSCP or CoS values are shown in the body of the table. The decade of the original DSCP value is shown in the left-side vertical column, and the units digit is in the top row. For example, the DSCP-CoS map indicates that if the original DSCP value is between 32 and 39, the CoS will be set to 4.

The CoS-DSCP and IP precedence-DSCP maps display the DSCP values to which each CoS or IP precedence value will be mapped. For example, the IP precedence-DSCP map indicates that if the original IP precedence value is 3, the DSCP will be set to 24.

This example shows how to verify the configuration of DSCP-mutation mapping:

Router# show mls qos maps | begin DSCP mutation
 
DSCP mutation map mutmap1:                  (dscp= d1d2)
     d1 :  d2 0  1  2  3  4  5  6  7  8  9 
     -------------------------------------
      0 :    00 01 02 03 04 05 06 07 08 09 
      1 :    10 11 12 13 14 15 16 17 18 19 
      2 :    20 21 22 23 24 25 26 27 28 29 
      3 :    08 31 32 33 34 35 36 37 38 39 
      4 :    40 41 42 43 44 45 46 47 48 49 
 <...Output Truncated...>
Router#

In the DSCP mutation map display, the marked-down DSCP values are shown in the body of the table. The first digit (d1) of the original DSCP value is in the left-side vertical column labeled d1, and the second digit (d2) is in the top row. For example, a DSCP value of 30 maps to a new DSCP value of 08.

Examples

The following example shows an interface summary for MPLS QoS classes in policy maps:

Router# show mls qos mpls
QoS Summary [MPLS]: (* - shared aggregates, Mod - switch module)
Int Mod Dir Class-map DSCP Agg Trust Fl AgForward-By AgPoliced-By 
Id Id 
---------------------------------------------------------------------------------------------------------------------- 
Fa3/38 5 In exp2 0 1 dscp 0 378900 0 
Fa3/41 5 In exp4 0 3 dscp 0 0 0
All 5 - Default 0 0* No 0 1191011240 0 

The table below describes the significant fields shown in the display.

Examples

This example shows how to display protocol pass-through information:

Router# show mls qos protocol
RIP : Passthru mode 
OSPF : Passthru mode
ND : Policing mode Cir = 32000 Burst = 1000
----- Module [5] ----- 
Routing protocol RIP is using AgId 0* 
Routing protocol OSPF is using AgId 0*
Routing protocol ND is using AgId 1
----- Module [6] ----- 
Routing protocol RIP is using AgId 0* 
Routing protocol OSPF is using AgId 0*

Examples

The following example shows sample output from the showmlsqosqueuinginterfacegigabitethernet5/1command on the Endor (RSP720-10G) card.

Router# show mls qos queuing interface gig5/1
Weighted Round-Robin
  Port QoS is enabled
  Port is untrusted
  Extend trust state: not trusted [COS = 0]
  Default COS is 0
    Queueing Mode In Tx direction: mode-cos
    Transmit queues [type = 1p3q8t]:
    Queue Id    Scheduling  Num of thresholds
    -----------------------------------------
       01         WRR                 08
       02         WRR                 08
       03         WRR                 08
       04         Priority            01
WRR bandwidth ratios:  100[queue 1] 150[queue 2] 200[queue 3] 
    queue-limit ratios:     50[queue 1]  20[queue 2]  15[queue 3]  15[Pri Queue]
    queue tail-drop-thresholds
    --------------------------
    1     70[1] 100[2] 100[3] 100[4] 100[5] 100[6] 100[7] 100[8] 
    2     70[1] 100[2] 100[3] 100[4] 100[5] 100[6] 100[7] 100[8] 
    3     100[1] 100[2] 100[3] 100[4] 100[5] 100[6] 100[7] 100[8] 
    queue random-detect-min-thresholds
    ----------------------------------
      1    40[1] 70[2] 70[3] 70[4] 70[5] 70[6] 70[7] 70[8] 
      2    40[1] 70[2] 70[3] 70[4] 70[5] 70[6] 70[7] 70[8] 
      3    70[1] 70[2] 70[3] 70[4] 70[5] 70[6] 70[7] 70[8] 
    queue random-detect-max-thresholds
    ----------------------------------
      1    70[1] 100[2] 100[3] 100[4] 100[5] 100[6] 100[7] 100[8] 
      2    70[1] 100[2] 100[3] 100[4] 100[5] 100[6] 100[7] 100[8] 
      3    100[1] 100[2] 100[3] 100[4] 100[5] 100[6] 100[7] 100[8] 
    WRED disabled queues:    
    queue thresh cos-map
    ---------------------------------------
    1     1      0 
    1     2      1 
    1     3      
    1     4      
    1     5      
    1     6      
    1     7      
    1     8      
    2     1      2 
    2     2      3 4 
    2     3      
    2     4      
    2     5      
    2     6      
    2     7      
    2     8      
    3     1      6 7 
    3     2      
    3     3      
    3     4      
    3     5      
    3     6      
    3     7      
    3     8      
    4     1      5 
    Queueing Mode In Rx direction: mode-cos
    Receive queues [type = 2q8t]:
    Queue Id    Scheduling  Num of thresholds
    -----------------------------------------
       01         WRR                 08
       02         WRR                 08
    WRR bandwidth ratios:  100[queue 1]   0[queue 2] 
    queue-limit ratios:    100[queue 1]   0[queue 2] 
    queue tail-drop-thresholds
    --------------------------
    1     100[1] 100[2] 100[3] 100[4] 100[5] 100[6] 100[7] 100[8] 
    2     100[1] 100[2] 100[3] 100[4] 100[5] 100[6] 100[7] 100[8] 
    queue random-detect-min-thresholds
    ----------------------------------
      1    40[1] 40[2] 50[3] 50[4] 50[5] 50[6] 50[7] 50[8] 
      2    100[1] 100[2] 100[3] 100[4] 100[5] 100[6] 100[7] 100[8] 
    queue random-detect-max-thresholds
    ----------------------------------
      1    70[1] 80[2] 90[3] 100[4] 100[5] 100[6] 100[7] 100[8] 
      2    100[1] 100[2] 100[3] 100[4] 100[5] 100[6] 100[7] 100[8] 
    queue thresh cos-map
    ---------------------------------------
    1     1      0 1 2 3 4 5 6 7 
    1     2      
    1     3      
    1     4      
    1     5      
    1     6      
    1     7      
    1     8      
    2     1      
    2     2      
    2     3      
    2     4      
    2     5      
    2     6      
    2     7      
    2     8      
  Packets dropped on Transmit:
    queue     dropped  [cos-map]
    ---------------------------------------------
    1                        0  [0 1 ]
    2                        0  [2 3 4 ]
    3                        0  [6 7 ]
    4                        0  [5 ]
  Packets dropped on Receive:
    BPDU packets:  0
    queue              dropped  [cos-map]
    ---------------------------------------------------
    1                        0  [0 1 2 3 4 5 6 7 ]
    2                        0  []
.
.
.

Examples

This example shows how to display information about the MLS-statistics data-export status and configuration:

Router# show mls qos statistics-export info 
QoS Statistics Data Export Status and Configuration information
---------------------------------------------------------------
Export Status : enabled
Export Interval : 250 seconds
Export Delimiter : @
Export Destination : 172.20.52.3, UDP port 514 Facility local6, Severity debug
 
QoS Statistics Data Export is enabled on following ports:
---------------------------------------------------------
FastEthernet5/24
 
QoS Statistics Data export is enabled on following shared aggregate policers:
-----------------------------------------------------------------------------
aggr1M
 
QoS Statistics Data Export is enabled on following class-maps:
---------------------------------------------------------------
class3

Examples

The following sample output from the showplatformhardwareaclentryglobal-qos command displays one result for inbound Address Resolution Protocol entries:

Switch# show platform hardware acl entry global-qos in arp
 
0x0000000000000003 arp ip any any mac any 

The following sample output from the showplatformhardwareaclentryglobal-qos command displays the detailed results for inbound Address Resolution Protocol entries (the legend provides definitions for abbreviations that may appear in the output):

Switch# show platform hardware acl entry global-qos in arp detail
------------------------------------------------------------------------------------------
ENTRY TYPE: A - ARP I - IPv4 M - MPLS O - MAC Entry S - IPv6(Six) C - Compaction L - L2V4 Suffix: D - dynamic entry E - exception entry R - reserved entry 
FIELDS: FS - first_seen/from_rp ACOS - acos/group_id F - ip_frag FF - frag_flag DPORT - dest_port SPORT - src_port LM - L2_miss GP - gpid_present ETYPE - enc_etype CEVLD - ce_vlan_valid MM - mpls_mcast FN - exp_from_null IV - ip_hdr_vld MV - mpls_valid E_CAU - exception_cause UK - U_key ACO - acos A/R - arp_rarp RR - req_repl GM - global_acl_fmt_match D-S-S-A - dest_mac_bcast, src_snd_mac_same, snd_tar_mac_same, arp_rarp_vld OM - ofe_mode SVLAN - Src_vlan
------------------------------------------------------------------------------------------

A

INDEX

LABEL

A/R

RR

IP SA

IP DA

SRC MAC

D-S-S-A

GM

LM

OM

RSLT

CNT

AR V

963

8191

1

7

0.0.0.0

0.0.0.0

FFFF.
FFFF.
FFFF

1-1-1-1

1

1

0

0x0000000000000003

0

AR M

963

0x0000

0

0x0

0.0.0.0

0.0.0.0

0000.
0000.
0000

0-0-0-1

0

0

1

Examples

The following is sample output from the show platform hardware pp active infrastructure pi npd rx policer command:

            
Router# show platform hardware pp active infrastructure pi npd rx policer 

PUNT POLICER
Ring |          Queue Name |           Punt rate |          Burst rate
-----+---------------------+---------------------+--------------------
 0   |     SW FORWARDING Q |                 500 |                1000 
 1   |  ROUTING PROTOCOL Q |                 500 |                1000 
 2   |              ICMP Q |                 500 |                1000 
 3   |              HOST Q |                1000 |                2000 
 4   |       ACL LOGGING Q |                 500 |                1000 
 5   |               STP Q |                3000 |                6000 
 6   |       L2 PROTOCOL Q |                1000 |                2000 
 7   |     MCAST CONTROL Q |                1000 |                2000 
 8   |         BROADCAST Q |                 500 |                1000 
 9   |               REP Q |                3000 |                6000 
10   |               CFM Q |                3000 |                6000 
11   |           CONTROL Q |                1000 |                2000 
12   |       IP MPLS TTL Q |                1000 |                2000 
13   |     DEFAULT MCAST Q |                 500 |                1000 
14   |  MCAST ROUTE DATA Q |                 500 |                1000 
15   |    MCAST MISMATCH Q |                 500 |                1000 
16   |          RPF FAIL Q |                 500 |                1000 
17   |  ROUTING THROTTLE Q |                 500 |                1000 
18   |             MCAST Q |                 500 |                1000 
19   |          MPLS OAM Q |                1000 |                2000 
20   |       IP MPLS MTU Q |                 500 |                1000 
21   |               PTP Q |                3000 |                6000 
22   |          LINUX ND Q |                 500 |                1000 
23   |         KEEPALIVE Q |                1000 |                2000 
24   |              ESMC Q |                3000 |                6000 
25   |          FPGA BFD Q |                3000 |                6000 
26   |          FPGA CCM Q |                3000 |                6000 
27   |          FPGA CFE Q |                3000 |                6000 
28   |          L2PT DUP Q |                4000 |                8000                   

      

The table below describes the significant fields shown in the display.

Examples

The following example shows how to see if the QoS: Packet Marking Statistics or QoS: Packet Matching Statistics feature is enabled:

Router# 
show platform hardware qfp active feature qos config global

Marker statistics are: enabled
Match per filter statistics are: enabled

The table below describes the significant fields shown in the display.

Examples

The following is a sample output of the showplatformlowqcommand.

Router# show platform lowq
TenGigabitEthernet10/1
Input Queue count:8     Output Queue count:8    Total Queue count:16

The following table describes the fields in the command:

Examples

The following example shows a router that has service policies configured only on VLAN interfaces:

Router# show platform qos policy-map
 
 service policy configured on int vlan: TRUE 
 # of int vlan service policy instances: 3 
 match input vlan service policy configured: FALSE 
 # of match input vlan service policy instances: 0 

The following example shows a router that has service policies configured on VLAN interfaces and that has a service policy configured with matchinputvlan. In this configuration, you must remove all service policies from their interfaces, and then configure only one type or another.

Router# show platform qos policy-map
 
 service policy configured on int vlan: TRUE 
 # of int vlan service policy instances: 1 
 match input vlan service policy configured: TRUE 
 # of match input vlan service policy instances: 1 

The table below describes each field shown in the showplatformqospolicy-map command:

Examples

The following is sample output from the show platform software infrastructure punt statistics command:

        Router# show platform software infrastructure punt statistics             
UEA Punt Statistics

Global drops : 0

 Queue Name             | Rx count                  |  Drop count
------------------------+---------------------------+-----------------------
 SW FORWARDING Q        | 0                         | 0                        
 ROUTING PROTOCOL Q     | 0                         | 0                        
 ICMP Q                 | 0                         | 0                        
 HOST Q                 | 57115                     | 0                        
 ACL LOGGING Q          | 0                         | 0                        
 STP Q                  | 0                         | 0                        
 L2 PROTOCOL Q          | 6571                      | 0                        
 MCAST CONTROL Q        | 208839                    | 0                        
 BROADCAST Q            | 4                         | 0                        
 REP Q                  | 0                         | 0                        
 CFM Q                  | 0                         | 0                        
 CONTROL Q              | 0                         | 0                        
 IP MPLS TTL Q          | 0                         | 0                        
 DEFAULT MCAST Q        | 0                         | 0                        
 MCAST ROUTE DATA Q     | 0                         | 0                        
 MCAST MISMATCH Q       | 0                         | 0                        
 RPF FAIL Q             | 0                         | 0                        
 ROUTING THROTTLE Q     | 87                        | 0                        
 MCAST Q                | 0                         | 0                        
 MPLS OAM Q             | 0                         | 0                        
 IP MPLS MTU Q          | 0                         | 0                        
 PTP Q                  | 0                         | 0                        
 LINUX ND Q             | 0                         | 0                        
 KEEPALIVE Q            | 0                         | 0                        
 ESMC Q                 | 0                         | 0                        
 FPGA BFD Q             | 0                         | 0                        
 FPGA CCM Q             | 0                         | 0                        
 FPGA CFE Q             | 0                         | 0                        
 L2PT DUP Q             | 0                         | 0                        

      

The table below describes the significant fields shown in the display.

Examples

The following is sample output from the showpolicy-managereventscommand:

Router# show policy-manager events
Event Statistics
0          catastrophic
0          critical
0          high
0          medium
0          low
0          positive
The following events were discarded
0          unknown
Event buffer pool
Number of free event buffers = 300
Number of events awaiting processing by Policy Manager process = 0

The table below describes the significant fields shown in the display.

Examples

The following is sample output from the showpolicy-managerpolicy command. The field descriptions are self-explanatory.

Router# show policy-manager policy 
Status (S) codes:
A = active
D = deactivated
S ID    Subsystem                 Name

Examples

This section provides sample output from typical showpolicy-mapcommands. Depending upon the interface or platform in use and the options enabled (for example, Weighted Fair Queueing [WFQ]), the output you see may vary slightly from the ones shown below.

Weighted Fair Queueing: Example

The following example displays the contents of the service policy map called po1. In this example, WFQ is enabled.

Router# show policy-map po1
Policy Map po1
 Weighted Fair Queueing
    Class class1
       Bandwidth 937 (kbps) Max thresh 64 (packets)
    Class class2
        Bandwidth 937 (kbps)  Max thresh 64 (packets)
    Class class3
        Bandwidth 937 (kbps)  Max thresh 64 (packets)
    Class class4
        Bandwidth 937 (kbps)  Max thresh 64 (packets)
    Class class5
        Bandwidth 937 (kbps)  Max thresh 64 (packets)
    Class class6
        Bandwidth 937 (kbps)  Max thresh 64 (packets)
    Class class7
        Bandwidth 937 (kbps)  Max thresh 64 (packets)
    Class class8
         Bandwidth 937 (kbps)  Max thresh 64 (packets)

The following example displays the contents of all policy maps on the router. Again, WFQ is enabled.

Router# show policy-map
 
Policy Map poH1
 Weighted Fair Queueing
    Class class1
       Bandwidth 937 (kbps) Max thresh 64 (packets)
    Class class2
        Bandwidth 937 (kbps)  Max thresh 64 (packets)
    Class class3
        Bandwidth 937 (kbps)  Max thresh 64 (packets)
    Class class4
        Bandwidth 937 (kbps)  Max thresh 64 (packets)
    Class class5
        Bandwidth 937 (kbps)  Max thresh 64 (packets)
    Class class6
        Bandwidth 937 (kbps)  Max thresh 64 (packets)
    Class class7
Bandwidth 937 (kbps)  Max thresh 64 (packets)
    Class class8
         Bandwidth 937 (kbps)  Max thresh 64 (packets)
Policy Map policy2
 Weighted Fair Queueing
    Class class1
       Bandwidth 300 (kbps) Max thresh 64 (packets)
    Class class2
        Bandwidth 300  (kbps)  Max thresh 64 (packets)
    Class class3
        Bandwidth 300 (kbps)  Max thresh 64 (packets)
    Class class4
        Bandwidth 300 (kbps)  Max thresh 64 (packets)
    Class class5
        Bandwidth 300 (kbps)  Max thresh 64 (packets)
    Class class6
        Bandwidth 300 (kbps)  Max thresh 64 (packets) 

The table below describes the significant fields shown in the display.

Frame Relay Voice-Adaptive Traffic-Shaping: Example

The following sample output for the show-policymap command indicates that Frame Relay voice-adaptive traffic-shaping is configured in the class-default class in the policy map MQC-SHAPE-LLQ1 and that the deactivation timer is set to 30 seconds.

Router# show policy-map
  Policy Map VSD1
    Class VOICE1
      Strict Priority
      Bandwidth 10 (kbps) Burst 250 (Bytes)
    Class SIGNALS1
      Bandwidth 8 (kbps) Max Threshold 64 (packets)
    Class DATA1
      Bandwidth 15 (kbps) Max Threshold 64 (packets)
  Policy Map MQC-SHAPE-LLQ1
    Class class-default
      Traffic Shaping
         Average Rate Traffic Shaping
                 CIR 63000 (bps) Max. Buffers Limit 1000 (Packets)
                 Adapt to 8000 (bps)
                 Voice Adapt Deactivation Timer 30 Sec 
      service-policy VSD1

Note	In Cisco IOS Release 12.4(20)T, if an interface configured with a policy map is full of heavy traffic, the implicit policer allows the traffic as defined in the bandwidth statement of each traffic class.

The table below describes the significant fields shown in the display.

Traffic Policing: Example

The following is sample output from the showpolicy-map command. This sample output displays the contents of a policy map called policy1. In policy 1, traffic policing on the basis of a committed information rate (CIR) of 20 percent has been configured, and the bc and be have been specified in milliseconds. As part of the traffic policing configuration, optional conform, exceed, and violate actions have been specified.

Router# show policy-map policy1
  Policy Map policy1
    Class class1
     police cir percent 20 bc 300 ms pir percent 40 be 400 ms
       conform-action transmit 
       exceed-action drop 
       violate-action drop 

The table below describes the significant fields shown in the display.

Two-Rate Traffic Policing: Example

The following is sample output from the showpolicy-map command when two-rate traffic policing has been configured. As shown below, two-rate traffic policing has been configured for a class called police. In turn, the class called police has been configured in a policy map called policy1. Two-rate traffic policing has been configured to limit traffic to an average committed rate of 500 kbps and a peak rate of 1 Mbps.

Router(config)# class-map police
Router(config-cmap)# match access-group 101
Router(config-cmap)# policy-map policy1
Router(config-pmap)# class police
Router(config-pmap-c)# police cir 500000 bc 10000 pir 1000000 be 10000 conform-action
transmit exceed-action set-prec-transmit 2 violate-action drop
Router(config-pmap-c)# interface serial3/0
Router(config-pmap-c)# exit
Router(config-pmap)# exit
Router(config)# interface serial3/0
Router(config-if)# service-policy output policy1
Router(config-if)# end
The following sample output shows the contents of the policy map called policy1 :
Router# show policy-map policy1

 Policy Map policy1
  Class police
   police cir 500000 conform-burst 10000 pir 1000000 peak-burst 10000 conform-action
   transmit exceed-action set-prec-transmit 2 violate-action drop

Traffic marked as conforming to the average committed rate (500 kbps) will be sent as is. Traffic marked as exceeding 500 kbps, but not exceeding 1 Mbps, will be marked with IP Precedence 2 and then sent. All traffic exceeding 1 Mbps will be dropped. The burst parameters are set to 10000 bytes.

The table below describes the significant fields shown in the display.

Multiple Traffic Policing Actions: Example

The following is sample output from the showpolicy-map command when the Policer Enhancement--Multiple Actions feature has been configured. The following sample output from the showpolicy-mapcommand displays the configuration for a service policy called police. In this service policy, traffic policing has been configured to allow multiple actions for packets marked as conforming to, exceeding, or violating the CIR or the PIR shown in the example.

Router# show policy-map police
  Policy Map police
    Class class-default
     police cir 1000000 bc 31250 pir 2000000 be 31250
       conform-action transmit 
       exceed-action set-prec-transmit 4
       exceed-action set-frde-transmit 
       violate-action set-prec-transmit 2
       violate-action set-frde-transmit 

Packets conforming to the specified CIR (1000000 bps) are marked as conforming packets. These are transmitted unaltered.

Packets exceeding the specified CIR (but not the specified PIR, 2000000 bps) are marked as exceeding packets. For these packets, the IP Precedence level is set to 4, the discard eligibility (DE) bit is set to 1, and the packet is transmitted.

Packets exceeding the specified PIR are marked as violating packets. For these packets, the IP Precedence level is set to 2, the DE bit is set to 1, and the packet is transmitted.

Note	Actions are specified by using the action argument of the police command. For more information about the available actions, see the police command reference page.

The table below describes the significant fields shown in the display.

Explicit Congestion Notification: Example

The following is sample output from the showpolicy-map command when the WRED--Explicit Congestion Notification (ECN) feature has been configured. The words "explicit congestion notification" (along with the ECN marking information) included in the output indicate that ECN has been enabled.

Router# show policy-map
   Policy Map pol1
     Class class-default
       Weighted Fair Queueing
             Bandwidth 70 (%)
             exponential weight 9
             explicit congestion notification
             class    min-threshold    max-threshold    mark-probability
             ----------------------------------------------------------
             ----------------------------------------------------------
 
             0        -                -                1/10
             1        -                -                1/10
             2        -                -                1/10
             3        -                -                1/10
             4        -                -                1/10
             5        -                -                1/10
             6        -                -                1/10
             7        -                -                1/10
             rsvp     -                -                1/10

The table below describes the significant fields shown in the display.

Modular QoS CLI (MQC) Unconditional Packet Discard: Example

The following example displays the contents of the policy map called policy1. All the packets belonging to the class called c1 are discarded.

Router# show policy-map
 policy1
 Policy Map policy1
  Class c1
   drop

The table below describes the significant fields shown in the display.

Percentage-Based Policing and Shaping: Example

The following example displays the contents of two service policy maps--one called policy1 and one called policy2. In policy1, traffic policing based on a CIR of 50 percent has been configured. In policy 2, traffic shaping based on an average rate of 35 percent has been configured.

Router# show policy-map policy1
Policy Map policy1
 class class1
    police cir percent 50
Router# show policy-map policy2
Policy Map policy2
 class class2
    shape average percent 35

The following example displays the contents of the service policy map called po1 :

Router# show policy-map po1
Policy Map po1
 Weighted Fair Queueing
    Class class1
Bandwidth 937 (kbps) Max thresh 64 (packets)
    Class class2
        Bandwidth 937 (kbps)  Max thresh 64 (packets)
    Class class3
        Bandwidth 937 (kbps)  Max thresh 64 (packets)
    Class class4
        Bandwidth 937 (kbps)  Max thresh 64 (packets)

The following example displays the contents of all policy maps on the router:

Router# show policy-map
 
Policy Map poH1
 Weighted Fair Queueing
    Class class1
       Bandwidth 937 (kbps) Max thresh 64 (packets)
    Class class2
        Bandwidth 937 (kbps)  Max thresh 64 (packets)
    Class class3
        Bandwidth 937 (kbps)  Max thresh 64 (packets)
    Class class4
        Bandwidth 937 (kbps)  Max thresh 64 (packets)
Policy Map policy2
 Weighted Fair Queueing
    Class class1
       Bandwidth 300 (kbps) Max thresh 64 (packets)
    Class class2
        Bandwidth 300  (kbps)  Max thresh 64 (packets)
    Class class3
        Bandwidth 300 (kbps)  Max thresh 64 (packets)
    Class class4
        Bandwidth 300 (kbps)  Max thresh 64 (packets)

The table below describes the significant fields shown in the display.

Enhanced Packet Marking: Example

The following sample output from the showpolicy-mapcommand displays the configuration for policy maps called policy1 and policy2.

In policy1 , a table map called table-map-cos1 has been configured to determine the precedence based on the class of service (CoS) value. Policy map policy 1 converts and propagates the packet markings defined in the table map called table-map-cos1.

The following sample output from the showpolicy-mapcommand displays the configuration for service polices called policy1 and policy2 . In policy1 , a table map called table-map1 has been configured to determine the precedence according to the CoS value. In policy2 , a table map called table-map2 has been configured to determine the CoS value according to the precedence value.

Router# show policy-map policy1
  Policy Map policy1
    Class class-default
      set precedence cos table table-map1
Router# show policy-map policy2
   Policy Map policy2
    Class class-default
      set cos precedence table table-map2

The table below describes the fields shown in the display.

Bandwidth-Remaining Ratio: Example

The following sample output for the show policy-map command indicates that the class-default class of the policy map named vlan10_policy has a bandwidth-remaining ratio of 10. When congestion occurs, the scheduler allocates class-default traffic 10 times the unused bandwidth allocated in relation to other subinterfaces.

Router# show policy-map vlan10_policy
  Policy Map vlan10_policy
    Class class-default
      Average Rate Traffic Shaping
      cir 1000000 (bps)
      bandwidth remaining ratio 10
      service-policy child_policy

The table below describes the fields shown in the display.

ATM Overhead Accounting: Example

The following sample output for the show policy-map command indicates that ATM overhead accounting is enabled for the class-default class. The BRAS-DSLAM encapsulation is dot1q and the subscriber encapsulation is snap-rbe for the AAL5 service.

Policy Map unit-test
Class class-default
Average Rate Traffic Shaping
cir 10% account dot1q aal5 snap-rbe

The table below describes the significant fields shown in the display.

Tunnel-Marking: Example

In this sample output of theshowpolicy-map command, the character string "ip precedence tunnel 4" indicates that tunnel marking (either L2TPv3 or GRE) has been configured to set the IP precedence value to 4 in the header of a tunneled packet.

Note	In Cisco IOS Release 12.4(15)T2, GRE-tunnel marking is supported on the RPM-XF platform only .

Router# show policy-map
Policy Map TUNNEL_MARKING
    Class MATCH_FRDE
      set ip precedence tunnel 4

The table below describes the fields shown in the display.

HQF: Example 1

The following sample output from the showpolicy-mapcommand displays the configuration for a policy map called test1:

Router# show policy-map test1
  Policy Map test1
    Class class-default
      Average Rate Traffic Shaping
      cir 1536000 (bps)
      service-policy test2

The table below describes the fields shown in the display.

HQF: Example 2

The following sample output from the showpolicy-mapcommand displays the configuration for a policy map called test2:

Router# show policy-map test2
  Policy Map test2
    Class RT
      priority 20 (%)
    Class BH
      bandwidth 40 (%)
      queue-limit 128 packets
    Class BL
      bandwidth 35 (%)
       packet-based wred, exponential weight 9
 
      dscp    min-threshold    max-threshold    mark-probablity
      ----------------------------------------------------------
      af21 (18)     100              400              1/10
      default (0)   -                -                1/10

The table below describes the fields shown in the display.

Examples

The following example displays configurations for the class called class7 that belongs to the policy map called po1:

Router# show policy-map po1 class class7


Class class7
 Bandwidth 937 (kbps) Max Thresh 64 (packets)

Examples

The following example shows that the policy map TEST is associated with the control plane. This policy map polices traffic that matches the class map TEST, while allowing all other traffic (that matches the class map called "class-default") to go through as is.

Router# show policy-map control-plane
 
Control Plane 
Service-policy input:TEST
Class-map:TEST (match-all)
      20 packets, 11280 bytes
      5 minute offered rate 0 bps, drop rate 0 bps
      Match:access-group 101
      police:
        8000 bps, 1500 limit, 1500 extended limit
        conformed 15 packets, 6210 bytes; action:transmit
        exceeded 5 packets, 5070 bytes; action:drop
        violated 0 packets, 0 bytes; action:drop
        conformed 0 bps, exceed 0 bps, violate 0 bps
Class-map:class-default (match-any)
      105325 packets, 11415151 bytes
      5 minute offered rate 0 bps, drop rate 0 bps
      Match:any

The table below describes the significant fields shown in the display.

Examples

This section provides sample output from typical showpolicy-mapinterfacecommands. Depending upon the interface or platform in use and the options enabled, the output you see may vary slightly from the ones shown below.

Weighted Fair Queueing (WFQ) on Serial Interface: Example

The following sample output of the showpolicy-mapinterface command displays the statistics for the serial 3/1 interface, to which a service policy called mypolicy (configured as shown below) is attached. Weighted fair queueing (WFQ) has been enabled on this interface. See the table below for an explanation of the significant fields that commonly appear in the command output.

policy-map mypolicy
 class voice
  priority 128
 class gold
  bandwidth 100
 class silver
  bandwidth 80
  random-detect
Router# show policy-map interface
 serial3/1 output
 Serial3/1 
  Service-policy output: mypolicy
    Class-map: voice (match-all)
      0 packets, 0 bytes
      5 minute offered rate 0 bps, drop rate 0 bps
      Match: ip precedence 5 
      Weighted Fair Queueing
        Strict Priority
        Output Queue: Conversation 264 
        Bandwidth 128 (kbps) Burst 3200 (Bytes)
        (pkts matched/bytes matched) 0/0
        (total drops/bytes drops) 0/0
    Class-map: gold (match-all)
      0 packets, 0 bytes
      5 minute offered rate 0 bps, drop rate 0 bps
      Match: ip precedence 2 
      Weighted Fair Queueing
        Output Queue: Conversation 265 
        Bandwidth 100 (kbps) Max Threshold 64 (packets)
        (pkts matched/bytes matched) 0/0
        (depth/total drops/no-buffer drops) 0/0/0
    Class-map: silver (match-all)
      0 packets, 0 bytes
      5 minute offered rate 0 bps, drop rate 0 bps
      Match: ip precedence 1 
      Weighted Fair Queueing
        Output Queue: Conversation 266 
        Bandwidth 80 (kbps)
        (pkts matched/bytes matched) 0/0
        (depth/total drops/no-buffer drops) 0/0/0
         exponential weight: 9
         mean queue depth: 0
class     Transmitted       Random drop      Tail drop    Minimum Maximum  Mark
          pkts/bytes        pkts/bytes       pkts/bytes    thresh  thresh  prob
0             0/0               0/0              0/0           20      40  1/10
1             0/0               0/0              0/0           22      40  1/10
2             0/0               0/0              0/0           24      40  1/10
3             0/0               0/0              0/0           26      40  1/10
4             0/0               0/0              0/0           28      40  1/10
5             0/0               0/0              0/0           30      40  1/10
6             0/0               0/0              0/0           32      40  1/10
7             0/0               0/0              0/0           34      40  1/10
rsvp          0/0               0/0              0/0           36      40  1/10
Class-map: class-default (match-any)
      0 packets, 0 bytes
      5 minute offered rate 0 bps, drop rate 0 bps
      Match: any 

Traffic Shaping on Serial Interface: Example

The following sample output from the showpolicy-mapinterface command displays the statistics for the serial 3/2 interface, to which a service policy called p1 (configured as shown below) is attached. Traffic shaping has been enabled on this interface. See the table below for an explanation of the significant fields that commonly appear in the command output.

Note	In HQF images for Cisco IOS Releases 12.4(20)T and later, the packets delayed and bytes delayed counters were removed for traffic shaping classes.

policy-map p1
 class c1
  shape average 320000
Router# show policy-map interface serial3/2 output
 Serial3/2 
  Service-policy output: p1
    Class-map: c1 (match-all)
      0 packets, 0 bytes
      5 minute offered rate 0 bps, drop rate 0 bps
      Match: ip precedence 0 
      Traffic Shaping
        Target    Byte   Sustain   Excess    Interval  Increment Adapt
        Rate      Limit  bits/int  bits/int  (ms)      (bytes)   Active
        320000    2000   8000      8000      25        1000      -
        Queue     Packets   Bytes     Packets   Bytes     Shaping
        Depth                         Delayed   Delayed   Active
        0         0         0         0         0         no
    Class-map: class-default (match-any)
      0 packets, 0 bytes
      5 minute offered rate 0 bps, drop rate 0 bps
      Match: any 

The table below describes significant fields commonly shown in the displays. The fields in the table are grouped according to the relevant QoS feature.

Precedence-Based Aggregate WRED on ATM Shared Port Adapter: Example

The following sample output of the showpolicy-mapinterface command displays the statistics for the ATM shared port adapter interface 4/1/0.10, to which a service policy called prec-aggr-wred (configured as shown below) is attached. Because aggregate WRED has been enabled on this interface, the classthrough Mark Prob statistics are aggregated by subclasses. See the table below for an explanation of the significant fields that commonly appear in the command output.

Router(config)# policy-map prec-aggr-wred
Router(config-pmap)# class class-default
Router(config-pmap-c)# random-detect aggregate
Router(config-pmap-c)# random-detect precedence values 0 1 2 3 minimum thresh 10 maximum-thresh 100 mark-prob 10
Router(config-pmap-c)# random-detect precedence values 4 5 minimum-thresh 40 maximum-thresh 400 mark-prob 10
Router(config-pmap-c)# random-detect precedence values 6 minimum-thresh 60 maximum-thresh 600 mark-prob 10
Router(config-pmap-c)# random-detect precedence values 7 minimum-thresh 70 maximum-thresh 700 mark-prob 10
Router(config-pmap-c)# exit
Router(config-pmap)# exit
Router(config)# interface ATM4/1/0.10 point-to-point
Router(config-if)# ip address 10.0.0.2 255.255.255.0
Router(config-if)# pvc 10/110

Router(config-if)# service-policy output prec-aggr-wred

Router# show policy-map interface atm4/1/0.10
 ATM4/1/0.10: VC 10/110 -
  Service-policy output: prec-aggr-wred
    Class-map: class-default (match-any)
      0 packets, 0 bytes
      5 minute offered rate 0 bps, drop rate 0 bps
      Match: any 
        Exp-weight-constant: 9 (1/512)
        Mean queue depth: 0
        class       Transmitted     Random drop      Tail drop     Minimum   Maximum  Mark
	pkts/bytes	pkts/bytes	pkts/bytes	thresh	thresh	prob
        
        0  1  2  3       0/0               0/0              0/0           10     100  1/10
        4  5             0/0               0/0              0/0           40     400  1/10
        6                0/0               0/0              0/0           60     600  1/10
        7                0/0               0/0              0/0           70     700  1/10

DSCP-Based Aggregate WRED on ATM Shared Port Adapter: Example

The following sample output of the showpolicy-mapinterface command displays the statistics for the ATM shared port adapter interface 4/1/0.11, to which a service policy called dscp-aggr-wred (configured as shown below) is attached. Because aggregate WRED has been enabled on this interface, the classthrough Mark Prob statistics are aggregated by subclasses. See the table below for an explanation of the significant fields that commonly appear in the command output.

Router(config)# policy-map dscp-aggr-wred
Router(config-pmap)# class class-default
Router(config-pmap-c)# random-detect dscp-based aggregate minimum-thresh 1 maximum-thresh 10 mark-prob 10
Router(config-pmap-c)# random-detect dscp values 0 1 2 3 4 5 6 7 minimum-thresh 10 maximum-thresh 20 mark-prob 10
Router(config-pmap-c)# random-detect dscp values 8 9 10 11 minimum-thresh 10 maximum-thresh 40 mark-prob 10
Router(config-pmap-c)# exit
Router(config-pmap)# exit
Router(config)# interface ATM4/1/0.11 point-to-point
Router(config-subif)# ip address 10.0.0.2 255.255.255.0
Router(config-subif)# pvc 11/101
Router(config-subif)# service-policy output dscp-aggr-wred
Router# show policy-map interface atm4/1/0.11
 ATM4/1/0.11: VC 11/101 -
  Service-policy output: dscp-aggr-wred
    Class-map: class-default (match-any)
      0 packets, 0 bytes
      5 minute offered rate 0 bps, drop rate 0 bps
      Match: any 
        Exp-weight-constant: 0 (1/1)
        Mean queue depth: 0
        class       Transmitted     Random drop      Tail drop     Minimum   Maximum  Mark
                  	pkts/bytes	pkts/bytes	pkts/bytes	thresh	thresh	prob
        default          0/0               0/0              0/0            1      10  1/10
        0  1  2  3 
        4  5  6  7       0/0               0/0              0/0           10      20  1/10
        8  9  10 11      0/0               0/0              0/0           10      40  1/10

The table below describes the significant fields shown in the display when aggregate WRED is configured for an ATM shared port adapter.

Frame Relay Voice-Adaptive Traffic-Shaping: Example

The following sample output shows that Frame Relay voice-adaptive traffic shaping is currently active and has 29 seconds left on the deactivation timer. With traffic shaping active and the deactivation time set, this means that the current sending rate on DLCI 201 is minCIR, but if no voice packets are detected for 29 seconds, the sending rate will increase to CIR.

Note	In HQF images for Cisco IOS Releases 12.4(20)T and later, the packets delayed and bytes delayed counters were removed for traffic shaping classes.

Router# show policy interface Serial3/1.1
 Serial3/1.1:DLCI 201 -
  Service-policy output:MQC-SHAPE-LLQ1
    
    Class-map:class-default (match-any)
      1434 packets, 148751 bytes
      30 second offered rate 14000 bps, drop rate 0 bps
      Match:any
      Traffic Shaping
           Target/Average   Byte   Sustain   Excess    Interval  Increment
             Rate           Limit  bits/int  bits/int  (ms)      (bytes)
            63000/63000     1890   7560      7560      120       945
    
        Adapt  Queue     Packets   Bytes     Packets   Bytes     Shaping
        Active Depth                         Delayed   Delayed   Active
        BECN   0         1434      162991    26        2704      yes
        Voice Adaptive Shaping active, time left 29 secs 

The table below describes the significant fields shown in the display. Significant fields that are not described in the table below are described in the table above (for "show policy-map interface Field Descriptions").

Two-Rate Traffic Policing: Example

The following is sample output from the showpolicy-mapinterfacecommand when two-rate traffic policing has been configured. In the example below, 1.25 Mbps of traffic is sent ("offered") to a policer class.

Router# show policy-map interface serial3/0

 Serial3/0
  Service-policy output: policy1
   Class-map: police (match all)
    148803 packets, 36605538 bytes
    30 second offered rate 1249000 bps, drop rate 249000 bps
    Match: access-group 101
    police:
     cir 500000 bps, conform-burst 10000, pir 1000000, peak-burst 100000
     conformed 59538 packets, 14646348 bytes; action: transmit
     exceeded 59538 packets, 14646348 bytes; action: set-prec-transmit 2
     violated 29731 packets, 7313826 bytes; action: drop
     conformed 499000 bps, exceed 500000 bps violate 249000 bps
   Class-map: class-default (match-any)
    19 packets, 1990 bytes
    30 seconds offered rate 0 bps, drop rate 0 bps
    Match: any

The two-rate traffic policer marks 500 kbps of traffic as conforming, 500 kbps of traffic as exceeding, and 250 kbps of traffic as violating the specified rate. Packets marked as conforming will be sent as is, and packets marked as exceeding will be marked with IP Precedence 2 and then sent. Packets marked as violating the specified rate are dropped.

The table below describes the significant fields shown in the display.

Multiple Traffic Policing Actions: Example

The following is sample output from the showpolicy-map command when the Policer Enhancement--Multiple Actions feature has been configured. The sample output from the showpolicy-mapinterface command displays the statistics for the serial 3/2 interface, to which a service policy called "police" (configured as shown below) is attached.

policy-map police
 class class-default
  police cir 1000000 pir 2000000
   conform-action transmit 
   exceed-action set-prec-transmit 4
   exceed-action set-frde-transmit 
   violate-action set-prec-transmit 2
   violate-action set-frde-transmit 
Router# show policy-map interface serial3/2
Serial3/2: DLCI 100 -
Service-policy output: police
    Class-map: class-default (match-any)
      172984 packets, 42553700 bytes
      5 minute offered rate 960000 bps, drop rate 277000 bps
      Match: any 
     police:
         cir 1000000 bps, bc 31250 bytes, pir 2000000 bps, be 31250 bytes
       conformed 59679 packets, 14680670 bytes; actions:
         transmit 
exceeded 59549 packets, 14649054 bytes; actions:
         set-prec-transmit 4
         set-frde-transmit 
       violated 53758 packets, 13224468 bytes; actions: 
         set-prec-transmit 2
         set-frde-transmit 
       conformed 340000 bps, exceed 341000 bps, violate 314000 bps

The sample output from showpolicy-mapinterface command shows the following:

• 59679 packets were marked as conforming packets (that is, packets conforming to the CIR) and were transmitted unaltered.
• 59549 packets were marked as exceeding packets (that is, packets exceeding the CIR but not exceeding the PIR). Therefore, the IP Precedence value of these packets was changed to an IP Precedence level of 4, the discard eligibility (DE) bit was set to 1, and the packets were transmitted with these changes.
• 53758 packets were marked as violating packets (that is, exceeding the PIR). Therefore, the IP Precedence value of these packets was changed to an IP Precedence level of 2, the DE bit was set to 1, and the packets were transmitted with these changes.

Note	Actions are specified by using the action argument of the police command. For more information about the available actions, see the policecommand reference page.

The table below describes the significant fields shown in the display.

Explicit Congestion Notification: Example

The following is sample output from the showpolicy-mapinterfacecommand when the WRED -- Explicit Congestion Notification (ECN) feature has been configured. The words "explicit congestion notification" included in the output indicate that ECN has been enabled.

Router# show policy-map interface
 Serial4/1
 Serial4/1
  Service-policy output:policy_ecn
        Class-map:prec1 (match-all)
          1000 packets, 125000 bytes
          30 second offered rate 14000 bps, drop rate 5000 bps
          Match:ip precedence 1
          Weighted Fair Queueing
            Output Queue:Conversation 42
            Bandwidth 20 (%)
            Bandwidth 100 (kbps)
            (pkts matched/bytes matched) 989/123625
        (depth/total drops/no-buffer drops) 0/455/0
             exponential weight:9
             explicit congestion notification
             mean queue depth:0
     class   Transmitted  Random drop  Tail drop   Minimum     Maximum     Mark
             pkts/bytes   pkts/bytes    pkts/bytes threshold   threshold   probability
       0       0/0          0/0          0/0          20          40        1/10
       1     545/68125      0/0          0/0          22          40        1/10
       2       0/0          0/0          0/0          24          40        1/10
       3       0/0          0/0          0/0          26          40        1/10
       4       0/0          0/0          0/0          28          40        1/10
       5       0/0          0/0          0/0          30          40        1/10
       6       0/0          0/0          0/0          32          40        1/10
       7       0/0          0/0          0/0          34          40        1/10
     rsvp      0/0          0/0          0/0          36          40        1/10
     class   ECN Mark 
            pkts/bytes
       0     0/0
       1    43/5375
       2     0/0
       3     0/0
       4     0/0
       5     0/0
       6     0/0
       7     0/0
     rsvp    0/0

The table below describes the significant fields shown in the display.

Class-Based RTP and TCP Header Compression: Example

The following sample output from the showpolicy-mapinterface command shows the RTP header compression has been configured for a class called "prec2" in the policy map called "p1".

The showpolicy-mapinterface command output displays the type of header compression configured (RTP), the interface to which the policy map called "p1" is attached (Serial 4/1), the total number of packets, the number of packets compressed, the number of packets saved, the number of packets sent, and the rate at which the packets were compressed (in bits per second (bps)).

In this example, User Datagram Protocol (UDP)/RTP header compressions have been configured, and the compression statistics are included at the end of the display.

Router# show policy-map interface Serial4/1
Serial4/1
Service-policy output:p1
    Class-map:class-default (match-any)
      1005 packets, 64320 bytes
      30 second offered rate 16000 bps, drop rate 0 bps
      Match:any
compress:
          header ip rtp
          UDP/RTP Compression:
          Sent:1000 total, 999 compressed,
                41957 bytes saved, 17983 bytes sent
                3.33 efficiency improvement factor
                99% hit ratio, five minute miss rate 0 misses/sec, 0 max
                 rate 5000 bps

The table below describes the significant fields shown in the display.

Modular QoS CLI (MQC) Unconditional Packet Discard: Example

The following sample output from the showpolicy-mapinterface command displays the statistics for the Serial2/0 interface, to which a policy map called "policy1" is attached. The discarding action has been specified for all the packets belonging to a class called "c1." In this example, 32000 bps of traffic is sent ("offered") to the class and all of them are dropped. Therefore, the drop rate shows 32000 bps.

Router# show policy-map interface
 Serial2/0
 Serial2/0 
  Service-policy output: policy1
    Class-map: c1 (match-all)
       10184 packets, 1056436 bytes
       5 minute offered rate 32000 bps, drop rate 32000 bps
       Match: ip precedence 0
       drop

The table below describes the significant fields shown in the display.

Percentage-Based Policing and Shaping: Example

The following sample output from the showpolicy-mapinterface command shows traffic policing configured using a CIR based on a bandwidth of 20 percent. The CIR and committed burst (Bc) in milliseconds (ms) are included in the display.

Router# show policy-map interface
 Serial3/1
 Serial3/1 
  Service-policy output: mypolicy
    Class-map: gold (match-any)
      0 packets, 0 bytes
      5 minute offered rate 0 bps, drop rate 0 bps
      Match: any
      police:
          cir 20 % bc 10 ms
          cir 2000000 bps, bc 2500 bytes
          pir 40 % be 20 ms
          pir 4000000 bps, be 10000 bytes
     conformed 0 packets, 0 bytes; actions:
      transmit
     exceeded 0 packets, 0 bytes; actions:
       drop
      violated 0 packets, 0 bytes; actions:
       drop
      conformed 0 bps, exceed 0 bps, violate 0 bps

The table below describes the significant fields shown in the display.

Traffic Shaping: Example

The following sample output from the showpolicy-mapinterface command (shown below) displays the statistics for the serial 3/2 interface. Traffic shaping has been enabled on this interface, and an average rate of 20 percent of the bandwidth has been specified.

Note	In HQF images for Cisco IOS Releases 12.4(20)T and later, the packets delayed and bytes delayed counters were removed for traffic shaping classes.

Router# show policy-map interface
 Serial3/2
Serial3/2 
  Service-policy output: p1
    Class-map: c1 (match-all)
      0 packets, 0 bytes
      5 minute offered rate 0 bps, drop rate 0 bps
      Match: any
      Traffic Shaping
        Target/Average      Byte   Sustain    Excess      Interval  Increment  Adapt
        Rate              Limit  bits/int  bits/int    (ms)     (bytes)   Active
         20 %                       10 (ms)    20 (ms)
        201500/201500       1952   7808       7808        38         976       -
        Queue     Packets   Bytes     Packets   Bytes     Shaping
        Depth                         Delayed   Delayed   Active
        0         0         0         0         0         no

The table below describes the significant fields shown in the display.

Packet Classification Based on Layer 3 Packet Length: Example

The following sample output from the showpolicy-mapinterface command displays the packet statistics for the Ethernet4/1 interface, to which a service policy called "mypolicy" is attached. The Layer 3 packet length has been specified as a match criterion for the traffic in the class called "class1".

Router# show policy-map interface
 Ethernet4/1
 Ethernet4/1 
  Service-policy input: mypolicy
    Class-map: class1 (match-all)
       500 packets, 125000 bytes
       5 minute offered rate 4000 bps, drop rate 0 bps
       Match: packet length min 100 max 300
       QoS Set
         qos-group 20
           Packets marked 500

The table below describes the significant fields shown in the display.

Enhanced Packet Marking: Example

The following sample output of the showpolicy-mapinterface command shows the service policies attached to a FastEthernet subinterface. In this example, a service policy called "policy1" has been attached. In "policy1", a table map called "table-map1" has been configured. The values in "table-map1" will be used to map the precedence values to the corresponding class of service (CoS) values.

Router# show policy-map interface
 FastEthernet1/0.1 
  Service-policy input: policy1
    Class-map: class-default (match-any)
      0 packets, 0 bytes
      5 minute offered rate 0 bps, drop rate 0 bps
      Match: any 
      QoS Set
        precedence cos table table-map1
          Packets marked 0

The table below describes the fields shown in the display.

Traffic Policing: Example

The following is sample output from the showpolicy-mapinterface command. This sample displays the statistics for the serial 2/0 interface on which traffic policing has been enabled. The committed (conform) burst (bc) and excess (peak) burst (be) are specified in milliseconds (ms).

Router# show policy-map interface serial2/0
 Serial2/0 
  Service-policy output: policy1 (1050)
    Class-map: class1 (match-all) (1051/1)
      0 packets, 0 bytes
      5 minute offered rate 0 bps, drop rate 0 bps
      Match: ip precedence 0  (1052)
      police:
          cir 20 % bc 300 ms
          cir 409500 bps, bc 15360 bytes
          pir 40 % be 400 ms
          pir 819000 bps, be 40960 bytes
        conformed 0 packets, 0 bytes; actions:
          transmit 
        exceeded 0 packets, 0 bytes; actions:
          drop 
        violated 0 packets, 0 bytes; actions:
          drop 
        conformed 0 bps, exceed 0 bps, violate 0 bps
    Class-map: class-default (match-any) (1054/0)
      0 packets, 0 bytes
      5 minute offered rate 0 bps, drop rate 0 bps
      Match: any  (1055)
        0 packets, 0 bytes
        5 minute rate 0 bps

In this example, the CIR and PIR are displayed in bps, and both the committed burst (bc) and excess burst (be) are displayed in bits.

The CIR, PIR bc, and be are calculated on the basis of the formulas described below.

Formula for Calculating the CIR: Example

When calculating the CIR, the following formula is used:

• CIR percentage specified (as shown in the output from the showpolicy-mapcommand) * bandwidth (BW) of the interface (as shown in the output from theshowinterfaces command) = total bits per second

According to the output from the showinterfacescommand for the serial 2/0 interface, the interface has a bandwidth (BW) of 2048 kbps.

Router# show interfaces serial2/0
Serial2/0 is administratively down, line protocol is down 
  Hardware is M4T
  MTU 1500 bytes, BW 2048 Kbit, DLY 20000 usec, rely 255/255, load 1/255 

The following values are used for calculating the CIR:

20 % * 2048 kbps = 409600 bps

Formula for Calculating the PIR: Example

When calculating the PIR, the following formula is used:

• PIR percentage specified (as shown in the output from the showpolicy-mapcommand) * bandwidth (BW) of the interface (as shown in the output from theshowinterfaces command) = total bits per second

According to the output from the showinterfaces command for the serial 2/0 interface, the interface has a bandwidth (BW) of 2048 kbps.

Router# show interfaces serial2/0
Serial2/0 is administratively down, line protocol is down 
  Hardware is M4T
  MTU 1500 bytes, BW 2048 Kbit, DLY 20000 usec, rely 255/255, load 1/255 

The following values are used for calculating the PIR:

40 % * 2048 kbps = 819200 bps

Note	Discrepancies between this total and the total shown in the output from theshowpolicy-mapinterface command can be attributed to a rounding calculation or to differences associated with the specific interface configuration.

Formula for Calculating the Committed Burst (bc): Example

When calculating the bc, the following formula is used:

• The bc in milliseconds (as shown in the showpolicy-map command) * the CIR in bits per seconds = total number bytes

The following values are used for calculating the bc:

300 ms * 409600 bps = 15360 bytes

Formula for Calculating the Excess Burst (be): Example

When calculating the bc and the be, the following formula is used:

• The be in milliseconds (as shown in the showpolicy-map command) * the PIR in bits per seconds = total number bytes

The following values are used for calculating the be:

400 ms * 819200 bps = 40960 bytes

The table below describes the significant fields shown in the display.

Bandwidth Estimation: Example

The following sample output from the showpolicy-mapinterface command displays statistics for the Fast Ethernet 0/1 interface on which bandwidth estimates for quality of service (QoS) targets have been generated.

The Bandwidth Estimation section indicates that bandwidth estimates for QoS targets have been defined. These targets include the packet loss rate, the packet delay rate, and the timeframe in milliseconds. Confidence refers to the drop-one-in value (as a percentage) of the targets. Corvil Bandwidth means the bandwidth estimate in kilobits per second.

When no drop or delay targets are specified, "none specified, falling back to drop no more than one packet in 500" appears in the output.

Router# show policy-map interface FastEthernet0/1
 FastEthernet0/1
  Service-policy output: my-policy
    Class-map: icmp (match-all)
      199 packets, 22686 bytes
      30 second offered rate 0 bps, drop rate 0 bps
      Match: access-group 101
      Bandwidth Estimation:
        Quality-of-Service targets:
          drop no more than one packet in 1000 (Packet loss < 0.10%)
          delay no more than one packet in 100 by 40 (or more) milliseconds
            (Confidence: 99.0000%)
        Corvil Bandwidth: 1 kbits/sec
    Class-map: class-default (match-any)
      112 packets, 14227 bytes
      30 second offered rate 0 bps, drop rate 0 bps
      Match: any
      Bandwidth Estimation:
        Quality-of-Service targets:
          <none specified, falling back to drop no more than one packet in 500
        Corvil Bandwidth: 1 kbits/sec

Shaping with HQF Enabled: Example

The following sample output from the showpolicy-mapinterface command shows that shaping is active (as seen in the queue depth field) with HQF enabled on the serial 4/3 interface. All traffic is classified to the class-default queue.

Note	In HQF images for Cisco IOS Releases 12.4(20)T and later, the packets delayed and bytes delayed counters were removed for traffic shaping classes.

Router# show policy-map interface serial4/3
 Serial4/3
  Service-policy output: shape
    Class-map: class-default (match-any)
      2203 packets, 404709 bytes
      30 second offered rate 74000 bps, drop rate 14000 bps
      Match: any
      Queueing
      queue limit 64 packets
      (queue depth/total drops/no-buffer drops) 64/354/0
      (pkts output/bytes output) 1836/337280
      shape (average) cir 128000, bc 1000, be 1000
      target shape rate 128000
        lower bound cir 0,  adapt to fecn 0
      Service-policy : LLQ
        queue stats for all priority classes:
         
          queue limit 64 packets
          (queue depth/total drops/no-buffer drops) 0/0/0
          (pkts output/bytes output) 0/0
        Class-map: c1 (match-all)
          0 packets, 0 bytes
          30 second offered rate 0 bps, drop rate 0 bps
          Match: ip precedence 1
          Priority: 32 kbps, burst bytes 1500, b/w exceed drops: 0
        Class-map: class-default (match-any)
          2190 packets, 404540 bytes
          30 second offered rate 74000 bps, drop rate 14000 bps
          Match: any
          queue limit 64 packets
          (queue depth/total drops/no-buffer drops) 63/417/0
          (pkts output/bytes output) 2094/386300

Packets Matched on the Basis of VLAN ID Number: Example

Note	As of Cisco IOS Release 12.2(31)SB2, matching packets on the basis of VLAN ID numbers is supported on the Catalyst 1000 platform only.

The following is a sample configuration in which packets are matched and classified on the basis of the VLAN ID number. In this sample configuration, packets that match VLAN ID number 150 are placed in a class called "class1."

Router# show class-map
Class Map match-all class1 (id 3)
Match vlan 150

Class1 is then configured as part of the policy map called "policy1." The policy map is attached to Fast Ethernet subinterface 0/0.1.

The following sample output of the showpolicy-mapinterface command displays the packet statistics for the policy maps attached to Fast Ethernet subinterface 0/0.1. It displays the statistics for policy1, in which class1 has been configured.

Router# show policy-map interface
FastEthernet0/0.1
! Policy-map name.
Service-policy input: policy1
! Class configured in the policy map.
Class-map: class1 (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
! VLAN ID 150 is the match criterion for the class.
Match: vlan 150
police:
cir 8000000 bps, bc 512000000 bytes
conformed 0 packets, 0 bytes; actions:
transmit
exceeded 0 packets, 0 bytes; actions:
drop
conformed 0 bps, exceed 0 bps
Class-map: class-default (match-any)
10 packets, 1140 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
10 packets, 1140 bytes
5 minute rate 0 bps

The table below describes the significant fields shown in the display.

Cisco 7600 Series Routers: Example

The following example shows how to display the statistics and the configurations of all the input and output policies that are attached to an interface on a Cisco 7600 series router:

Router# show policy-map interface
 FastEthernet5/36
  service-policy input: max-pol-ipp5
    class-map: ipp5 (match-all)
      0 packets, 0 bytes
      5 minute rate 0 bps
      match: ip precedence 5
  class ipp5
    police 2000000000 2000000 conform-action set-prec-transmit 6 exceed-action p
policed-dscp-transmit

The following example shows how to display the input-policy statistics and the configurations for a specific interface on a Cisco 7600 series router:

Router# show policy-map interface fastethernet 5/36 input
 FastEthernet5/36
  service-policy input: max-pol-ipp5
    class-map: ipp5 (match-all)
      0 packets, 0 bytes
      5 minute rate 0 bps
      match: ip precedence 5
  class ipp5
    police 2000000000 2000000 conform-action set-prec-transmit 6 exceed-action p
policed-dscp-transmit

The table below describes the significant fields shown in the display.

Cisco 7200 Series Routers: Example

The following example shows the automatic rounding-off of the bc and be values, in the MQC police policy-map, to the interface's MTU size in a Cisco 7200 series router. The rounding-off is done only when the bc and be values are lesser than the interface's MTU size.

Router# show policy-map interface
Service-policy output: p2
Service-policy output: p2
    Class-map: class-default (match-any)
      2 packets, 106 bytes
      30 second offered rate 0000 bps, drop rate 0000 bps
      Match: any 
        2 packets, 106 bytes
        30 second rate 0 bps
      police:
          cir 10000 bps, bc 4470 bytes
          pir 20000 bps, be 4470 bytes
        conformed 0 packets, 0 bytes; actions:
          transmit
        exceeded 0 packets, 0 bytes; actions:
          drop
        violated 0 packets, 0 bytes; actions:
          drop

conformed 0000 bps, exceed 0000 bps, violate 0000 bps

Multiple Priority Queues on Serial Interface: Example

The following sample output from the show policy-map interface command shows the types of statistical information that displays when multiple priority queues are configured. Depending upon the interface in use and the options enabled, the output that you see may vary slightly from the output shown below.

Router# show policy-map interface
Serial2/1/0
Service-policy output: P1
Queue statistics for all priority classes:
.
.
.
Class-map: Gold (match-all)
0 packets, 0 bytes			/*Updated for each priority level configured.*/
5 minute offered rate 0 bps, drop rate 0 bps
Match: ip precedence 2
Priority: 0 kbps, burst bytes 1500, b/w exceed drops: 0
Priority Level 4:
0 packets, 0 bytes

Bandwidth-Remaining Ratios: Example

The following sample output from the show policy-map interface command indicates that bandwidth-remaining ratios are configured for class queues. As shown in the example, the classes precedence_0, precedence_1, and precedence_2 have bandwidth-remaining ratios of 20, 40, and 60, respectively.

Router# show policy-map interface GigabitEthernet1/0/0.10
  Service-policy output: vlan10_policy
    Class-map: class-default (match-any)
      0 packets, 0 bytes
      30 second offered rate 0 bps, drop rate 0 bps
      Match: any
        0 packets, 0 bytes
        30 second rate 0 bps
      Queueing
      queue limit 250 packets
      (queue depth/total drops/no-buffer drops) 0/0/0
      (pkts output/bytes output) 0/0
      shape (average) cir 1000000, bc 4000, be 4000
      target shape rate 1000000
      bandwidth remaining ratio 10
      Service-policy : child_policy
        Class-map: precedence_0 (match-all)
          0 packets, 0 bytes
          30 second offered rate 0 bps, drop rate 0 bps
          Match: ip precedence 0
          Queueing
          queue limit 62 packets
          (queue depth/total drops/no-buffer drops) 0/0/0
          (pkts output/bytes output) 0/0
          shape (average) cir 500000, bc 2000, be 2000
          target shape rate 500000
          bandwidth remaining ratio 20
        Class-map: precedence_1 (match-all)
          0 packets, 0 bytes
          30 second offered rate 0 bps, drop rate 0 bps
          Match: ip precedence 1
          Queueing
          queue limit 62 packets
          (queue depth/total drops/no-buffer drops) 0/0/0
          (pkts output/bytes output) 0/0
          shape (average) cir 500000, bc 2000, be 2000
          target shape rate 500000
          bandwidth remaining ratio 40
        Class-map: precedence_2 (match-all)
          0 packets, 0 bytes
          30 second offered rate 0 bps, drop rate 0 bps
          Match: ip precedence 2
          Queueing
          queue limit 62 packets
          (queue depth/total drops/no-buffer drops) 0/0/0
          (pkts output/bytes output) 0/0
          shape (average) cir 500000, bc 2000, be 2000
          target shape rate 500000
          bandwidth remaining ratio 60
        Class-map: class-default (match-any)
          0 packets, 0 bytes
          30 second offered rate 0 bps, drop rate 0 bps
          Match: any
            0 packets, 0 bytes
            30 second rate 0 bps
         
          queue limit 62 packets
          (queue depth/total drops/no-buffer drops) 0/0/0
          (pkts output/bytes output) 0/0 

The table below describes the significant fields shown in the display.

Tunnel Marking: Example

In this sample output of theshowpolicy-mapinterface command, the character string "ip dscp tunnel 3" indicates that L2TPv3 tunnel marking has been configured to set the DSCP value to 3 in the header of a tunneled packet.

Router# show policy-map interface
 Serial0 
  Service-policy input: tunnel
    Class-map: frde (match-all)
      0 packets, 0 bytes
      30 second offered rate 0 bps, drop rate 0 bps
      Match: fr-de 
      QoS Set
        ip dscp tunnel 3
          Packets marked 0
    Class-map: class-default (match-any) 
      13736 packets, 1714682 bytes
      30 second offered rate 0 bps, drop rate 0 bps
      Match: any 
        13736 packets, 1714682 bytes
        30 second rate 0 bps

The table below describes the significant fields shown in the display.

Traffic Shaping Overhead Accounting for ATM: Example

The following output from the show policy-map interface command indicates that ATM overhead accounting is enabled for shaping and disabled for bandwidth:

Router# show policy-map interface
Service-policy output:unit-test
Class-map: class-default (match-any)
100 packets, 1000 bytes
30 second offered rate 800 bps, drop rate 0 bps
Match: any
shape (average) cir 154400, bc 7720, be 7720
target shape rate 154400
overhead accounting: enabled
bandwidth 30% (463 kbps)
overhead accounting: disabled
queue limit 64 packets
(queue depth/total drops/no-buffer drops) 0/0/0
(packets output/bytes output) 100/1000

The table below describes the significant fields shown in the display.