IPv6 Configuration Guide, Cisco IOS Release 12.4T
Implementing VoIP for IPv6
Download this chapter
Implementing VoIP for IPv6Implementing VoIP for IPv6
Download the complete book
IPv6 Configuration Guide, Cisco IOS Release 12.4TIPv6 Configuration Guide, Cisco IOS Release 12.4T (PDF - 6 MB)
 Feedback

Contents

Implementing VoIP for IPv6

Last Updated: February 15, 2012

This document describes VoIP in IPv6 (VoIPv6), a feature that adds IPv6 capability to existing VoIP features. This feature adds dual-stack (IPv4 and IPv6) support on voice gateways and media termination points (MTPs), IPv6 support for Session Initiation Protocol (SIP) trunks, and support for Skinny Client Control Protocol (SCCP)-controlled analog voice gateways. In addition, the Session Border Controller (SBC) functionality of connecting a SIP IPv4 or H.323 IPv4 network to a SIP IPv6 network is implemented on a Cisco Unified Border Element to facilitate migration from VoIPv4 to VoIPv6.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the Feature Information Table at the end of this document.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.

Prerequisites for Implementing VoIP for IPv6

  • This document assumes that you are familiar with IPv6 and IPv4. See the publications referenced in the Additional References section for IPv6 and IPv4 configuration and command reference information.
  • Perform basic IPv6 addressing and basic connectivity as described in Implementing IPv6 Addressing and Basic Connectivity.
  • Cisco Express Forwarding for IPv6 must be enabled.
  • Perform basic voice configurations as described in the Voice Configuration Library .

Restrictions for Implementing VoIP for IPv6

The following platforms are supported in Cisco IOS Release 12.4(22)T:

  • Integrated Services Routers (2801, 2821, 2851, 3825, 3845)
  • VG202/204 (Orbity)
  • VG224
  • IAD2430
  • AS5400XM

Information About Implementing VoIP for IPv6

SIP Voice Gateways in VoIPv6

SIP is a simple, ASCII-based protocol that uses requests and responses to establish communication among the various components in the network and to ultimately establish a conference between two or more endpoints.

For further information about this feature and information about configuring the SIP voice gateway for VoIPv6, see the Configuring a SIP Voice Gateway for IPv6.

Cisco Unified Border Element in VoIPv6

The Cisco Unified Border Element feature adds IPv6 capability to existing VoIP features. This feature adds dual-stack support on voice gateways and MTP, IPv6 support for SIP trunks, and support for SCCP-controlled analog voice gateways. Real-time control protocol (RTCP) Pass-through and T.38 Fax over IPv6 have also been added to Cisco UBE. For more information on this feature, see the "Configuring RTCP Pass-through and T.38 Fax Support on Cisco UBE for IPv6" section on page 19

For further information about this feature and information about configuring the Cisco Unified Border Element in VoIPv6see the Configuring H.323 IPv4-to-SIPv6 Connections in a Cisco Unified Border Element.

MTP Used with Voice Gateways in VoIPv6

Cisco IOS MTP trusted relay point (TRP) supports media interoperation between IPv4 and IPv6 networks.

For further information about this feature and information about configuring the SIP voice gateway for IPv6, see the Configuring MTP Used with Voice Gateways.

How to Implement VoIP for IPv6

Configuring a SIP Voice Gateway for IPv6

SIP is a simple, ASCII-based protocol that uses requests and responses to establish communication among the various components in the network and to ultimately establish a conference between two or more endpoints.

Users in a SIP network are identified by unique SIP addresses. A SIP address is similar to an e-mail address and is in the format of sip:userID@gateway.com. The user ID can be either a username or an E.164 address. The gateway can be either a domain (with or without a hostname) or a specific Internet IPv4 or IPv6 address.

A SIP trunk can operate in one of three modes: SIP trunk in IPv4-only mode, SIP trunk in IPv6-only mode, and SIP trunk in dual-stack mode, which supports both IPv4 and IPv6.

A SIP trunk uses the Alternative Network Address Transport (ANAT) mechanism to exchange multiple IPv4 and IPv6 media addresses for the endpoints in a session. ANAT is automatically enabled on SIP trunks in dual-stack mode. The ANAT Session Description Protocol (SDP) grouping framework allows user agents (UAs) to include both IPv4 and IPv6 addresses in their SDP session descriptions. The UA is then able to use any of its media addresses to establish a media session with a remote UA.

A Cisco Unified Border Element can interoperate between H.323/SIP IPv4 and SIP IPv6 networks in media flow-through mode. In media flow-through mode, both signaling and media flows through the Cisco Unified Border Element, and the Cisco Unified Border Element performs both signaling and media interoperation between H.323/SIP IPv4 and SIP IPv6 networks (see the figure below).

Figure 1H.323/SIP IPv4--SIP IPv6 Interoperating in Media Flow-Through Mode


Perform the tasks in the following sections to configure a SIP voice gateway for IPv6:

Restrictions

Virtual routing and forwarding (VRF) is not supported in IPv6 calls.

Shutting Down or Enabling VoIPv6 Service on Cisco Gateways

Perform this task to shut down or enable VoIPv6 service on Cisco gateways.

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    voice service voip

4.    shutdown [forced]


DETAILED STEPS
 Command or ActionPurpose
Step 1
enable


Example:

Router> enable

 

Enables privileged EXEC mode.

  • Enter your password if prompted.
 
Step 2
configure terminal


Example:

Router# configure terminal

 

Enters global configuration mode.

 
Step 3
voice service voip


Example:

Router(config)# voice service voip

 

Enters voice service VoIP configuration mode.

 
Step 4
shutdown [forced]


Example:

Router(config-voi-serv)# shutdown forced

 

Shuts down or enables VoIP call services.

 

Shutting Down or Enabling VoIPv6 Submodes on Cisco Gateways

Perform this task to shut down or enable VoIPv6 submodes on Cisco gateways.

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    voice service voip

4.    sip

5.    call service stop [forced] [maintain-registration


DETAILED STEPS
 Command or ActionPurpose
Step 1
enable


Example:

Router> enable

 

Enables privileged EXEC mode.

  • Enter your password if prompted.
 
Step 2
configure terminal


Example:

Router# configure terminal

 

Enters global configuration mode.

 
Step 3
voice service voip


Example:

Router(config)# voice service voip

 

Enters voice service VoIP configuration mode.

 
Step 4
sip


Example:

Router(config-voi-serv)# sip

 

Enters SIP configuration mode.

 
Step 5
call service stop [forced] [maintain-registration


Example:

Router(config-serv-sip)# call service stop

 

Shuts down or enables VoIPv6 for the selected submode.

 

Configuring the Protocol Mode of the SIP Stack

Perform this task to configure the SIP stack's protocol mode.

Before You Begin

SIP service should be shut down before configuring the protocol mode. After configuring the protocol mode as IPv6, IPv4, or dual-stack, SIP service should be reenabled.


SUMMARY STEPS

1.    enable

2.    configure terminal

3.    sip-ua

4.    protocol mode ipv4 | ipv6 | dual-stack [preference {ipv4 | ipv6}]}


DETAILED STEPS
 Command or ActionPurpose
Step 1
enable


Example:

Router> enable

 

Enables privileged EXEC mode.

  • Enter your password if prompted.
 
Step 2
configure terminal


Example:

Router# configure terminal

 

Enters global configuration mode.

 
Step 3
sip-ua


Example:

Router(config)# sip-ua

 

Enters SIP user agent configuration mode.

 
Step 4
protocol mode ipv4 | ipv6 | dual-stack [preference {ipv4 | ipv6}]}


Example:

Router(config-sip-ua)# protocol mode dual-stack

 

Configures the Cisco IOS SIP stack in dual-stack mode.

 
Disabling ANAT Mode

ANAT is automatically enabled on SIP trunks in dual-stack mode. Perform this task to disable ANAT in order to use a single-stack mode.

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    voice service voip

4.    sip

5.    no anat


DETAILED STEPS
 Command or ActionPurpose
Step 1
enable


Example:

Router> enable

 

Enables privileged EXEC mode.

  • Enter your password if prompted.
 
Step 2
configure terminal


Example:

Router# configure terminal

 

Enters global configuration mode.

 
Step 3
voice service voip


Example:

Router(config)# voice service voip

 

Enters voice service VoIP configuration mode.

 
Step 4
sip


Example:

Router(config-voi-serv)# sip

 

Enters SIP configuration mode.

 
Step 5
no anat


Example:

router(conf-serv-sip)# no anat

 

Disables ANAT on a SIP trunk.

 

Configuring the Source IPv6 Address of Signaling and Media Packets

Users can configure the source IPv4 or IPv6 address of signaling and media packets to a specific interface's IPv4 or IPv6 address. Thus, the address that goes out on the packet is bound to the IPv4 or IPv6 address of the interface specified with the bind command.

The bind command also can be configured with one IPv6 address to force the gateway to use the configured address when the bind interface has multiple IPv6 addresses. The bind interface should have both IPv4 and IPv6 addresses to send out ANAT.

When you do not specify a bind address or if the interface is down, the IP layer still provides the best local address.

Perform this task to configure the source IPv6 address of signaling and media packets.

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    voice service voip

4.    sip

5.    bind {control | media | all} source interface interface-id [ipv6-address ipv6-address


DETAILED STEPS
 Command or ActionPurpose
Step 1
enable


Example:

Router> enable

 

Enables privileged EXEC mode.

  • Enter your password if prompted.
 
Step 2
configure terminal


Example:

Router# configure terminal

 

Enters global configuration mode.

 
Step 3
voice service voip


Example:

Router(config)# voice service voip

 

Enters voice service VoIP configuration mode.

 
Step 4
sip


Example:

Router(config-voi-serv)# sip

 

Enters SIP configuration mode.

 
Step 5
bind {control | media | all} source interface interface-id [ipv6-address ipv6-address


Example:

Router(config-serv-sip)# bind control source- interface FastEthernet0/0

 

Binds the source address for signaling and media packets to the IPv6 address of a specific interface.

 

Configuring the SIP Server

Perform this task to configure a SIP server.

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    sip-ua

4.    sip-server {dns: host-name] | ipv4: ipv4-address | ipv6: [ipv6-address] :[port-nums]}

5.    keepalive target {{ipv4 : address | ipv6 : address}[: port] | dns : hostname } [ tcp [ tls ]] | udp] [secondary]


DETAILED STEPS
 Command or ActionPurpose
Step 1
enable


Example:

Router> enable

 

Enables privileged EXEC mode.

  • Enter your password if prompted.
 
Step 2
configure terminal


Example:

Router# configure terminal

 

Enters global configuration mode.

 
Step 3
sip-ua


Example:

Router(config)# sip-ua

 

Enters SIP user agent configuration mode.

 
Step 4
sip-server {dns: host-name] | ipv4: ipv4-address | ipv6: [ipv6-address] :[port-nums]}

Example:

Router(config-sip-ua)# sip-server ipv6:[2001:DB8:0:0:8:800:200C:417A]

 

Configures a network address for the SIP server interface.

 
Step 5
keepalive target {{ipv4 : address | ipv6 : address}[: port] | dns : hostname } [ tcp [ tls ]] | udp] [secondary]


Example:

Router(config-sip-ua)# keepalive target ipv6:[2001:DB8:0:0:8:800:200C:417A

 

Identifies SIP servers that will receive keepalive packets from the SIP gateway.

 

Configuring the Session Target

Perform this task to configure the session target.

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    dial-peer voice tag {mmoip | pots | vofr | voip}

4.    destination pattern [+ string T

5.    session target {ipv4: destination-address| ipv6: [ destination-address ]| dns : $s$. | $d$. | $e$. | $u$.] host-name | enum:table -num | loopback:rtp | ras| sip-server} [: port


DETAILED STEPS
 Command or ActionPurpose
Step 1
enable


Example:

Router> enable

 

Enables privileged EXEC mode.

  • Enter your password if prompted.
 
Step 2
configure terminal


Example:

Router# configure terminal

 

Enters global configuration mode.

 
Step 3
dial-peer voice tag {mmoip | pots | vofr | voip}


Example:

Router(config)# dial-peer voice 29 voip

 

Defines a particular dial peer, specifies the method of voice encapsulation, and enters dial peer configuration mode.

 
Step 4
destination pattern [+ string T


Example:

Router(config-dial-peer)# destination-pattern 7777

 

Specifies either the prefix or the full E.164 telephone number to be used for a dial peer.

 
Step 5
session target {ipv4: destination-address| ipv6: [ destination-address ]| dns : $s$. | $d$. | $e$. | $u$.] host-name | enum:table -num | loopback:rtp | ras| sip-server} [: port


Example:

Router(config-dial-peer)# session target [ipv6:2001:DB8:0:0:8:800:200C:417A]

 

Designates a network-specific address to receive calls from a VoIP or VoIPv6 dial peer.

 

Configuring SIP Register Support

Perform this task to configure SIP register support.

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    sip-ua

4.    registrar {dns: address | ipv4: destination-address [: port] | ipv6: destination-address : port] } aor-domain expires seconds [tcp tls] ] type [secondary] [scheme string]

5.    retry register retries

6.    timers register milliseconds


DETAILED STEPS
 Command or ActionPurpose
Step 1
enable


Example:

Router> enable

 

Enables privileged EXEC mode.

  • Enter your password if prompted.
 
Step 2
configure terminal


Example:

Router# configure terminal

 

Enters global configuration mode.

 
Step 3
sip-ua


Example:

Router(config)# sip-ua

 

Enters SIP user agent configuration mode.

 
Step 4
registrar {dns: address | ipv4: destination-address [: port] | ipv6: destination-address : port] } aor-domain expires seconds [tcp tls] ] type [secondary] [scheme string]


Example:

Router(config-sip-ua)# registrar ipv6:[2001:DB8::1:20F:F7FF:FE0B:2972] expires 3600 secondary

 

Enables SIP gateways to register E.164 numbers on behalf of analog telephone voice ports, IP phone virtual voice ports, and SCCP phones with an external SIP proxy or SIP registrar.

 
Step 5
retry register retries


Example:

Router(config-sip-ua)# retry register 10

 

Configures the total number of SIP register messages that the gateway should send.

 
Step 6
timers register milliseconds


Example:

Router(config-sip-ua)# timers register 500

 

Configures how long the SIP UA waits before sending register requests.

 

Configuring Outbound Proxy Server Globally on a SIP Gateway

Perform this task to configure an outbound-proxy server globally on a SIP gateway.

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    voice service voip

4.    sip

5.    outbound-proxy {ipv4: ipv4-address | ipv6: ipv6-address | dns: host : domain} [: port-number]


DETAILED STEPS
 Command or ActionPurpose
Step 1
enable


Example:

Router> enable

 

Enables privileged EXEC mode.

  • Enter your password if prompted.
 
Step 2
configure terminal


Example:

Router# configure terminal

 

Enters global configuration mode.

 
Step 3
voice service voip


Example:

Router(config)# voice service voip

 

Enters voice service VoIP configuration mode.

 
Step 4
sip


Example:

Router(config-voi-serv)# sip

 

Enters sip configuration mode.

 
Step 5
outbound-proxy {ipv4: ipv4-address | ipv6: ipv6-address | dns: host : domain} [: port-number]


Example:

Router(config-serv-sip)# outbound-proxy ipv6 [2001:DB8:0:0:8:800:200C:417A]

 

Specifies the SIP outbound proxy globally for a Cisco IOS voice gateway using an IPv6 address.

 

Verifying SIP Gateway Status

SUMMARY STEPS

1.    show sip-ua calls

2.    show sip-ua connections

3.    show sip-ua status


DETAILED STEPS
Step 1   show sip-ua calls

The show sip-ua calls command displays active user agent client (UAC) and user agent server (UAS) information on SIP calls:

Router# show sip-ua calls 


          
SIP UAC CALL INFO


          


          
Call 1


          
SIP Call ID                : 8368ED08-1C2A11DD-80078908-BA2972D0@2001::21B:D4FF:FED7:B000


          
   State of the call       : STATE_ACTIVE (7)


          
   Substate of the call    : SUBSTATE_NONE (0)


          
   Calling Number          : 2000


          
   Called Number           : 1000


          
   Bit Flags               : 0xC04018 0x100 0x0


        
         

Example:
          
   CC Call ID              : 2
   Source IP Address (Sig ): 2001:DB8:0:ABCD::1
   Destn SIP Req Addr:Port : 2001:DB8:0:0:FFFF:5060
   Destn SIP Resp Addr:Port: 2001:DB8:0:1:FFFF:5060
   Destination Name        : 2001::21B:D5FF:FE1D:6C00
   Number of Media Streams : 1
   Number of Active Streams: 1
   RTP Fork Object         : 0x0
   Media Mode              : flow-through
   Media Stream 1
     State of the stream      : STREAM_ACTIVE
     Stream Call ID           : 2
     Stream Type              : voice-only (0)
     Stream Media Addr Type   : 1709707780
     Negotiated Codec         :  (20 bytes)
     Codec Payload Type       : 18 
     Negotiated Dtmf-relay    : inband-voice
     Dtmf-relay Payload Type  : 0
     Media Source IP Addr:Port: [2001::21B:D4FF:FED7:B000]:16504
     Media Dest IP Addr:Port  : [2001::21B:D5FF:FE1D:6C00]:19548
Options-Ping    ENABLED:NO    ACTIVE:NO
   Number of SIP User Agent Client(UAC) calls: 1
SIP UAS CALL INFO
   Number of SIP User Agent Server(UAS) calls: 0



        
      


      
Step 2  
        
          
            show
            sip-ua
            connections
          
        

         
          

Use the show sip-ua connections command to display SIP UA transport connection tables:


        
         

Example:
          
Router# show sip-ua connections udp brief 
Total active connections      : 1
No. of send failures          : 0
No. of remote closures        : 0
No. of conn. failures         : 0
No. of inactive conn. ageouts : 0
Router# show sip-ua connections udp detail
 
Total active connections      : 1
No. of send failures          : 0
No. of remote closures        : 0
No. of conn. failures         : 0
No. of inactive conn. ageouts : 0
---------Printing Detailed Connection Report---------
Note:
 ** Tuples with no matching socket entry
    - Do 'clear sip <tcp[tls]/udp> conn t ipv4:<addr>:<port>'
      to overcome this error condition
 ++ Tuples with mismatched address/port entry
    - Do 'clear sip <tcp[tls]/udp> conn t ipv4:<addr>:<port> id <connid>'
      to overcome this error condition
Remote-Agent:2001::21B:D5FF:FE1D:6C00, Connections-Count:1
  Remote-Port Conn-Id Conn-State  WriteQ-Size
  =========== ======= =========== ===========
         5060       2 Established           0



        
      


      
Step 3  
        
          
            show
            sip-ua
            status
          
        

         
          

Use the show sip-ua status command to display the status of the SIP UA:


        
         

Example:
          
Router# show sip-ua status
SIP User Agent Status
SIP User Agent for UDP : ENABLED
SIP User Agent for TCP : ENABLED
SIP User Agent for TLS over TCP : ENABLED
SIP User Agent bind status(signaling): DISABLED 
SIP User Agent bind status(media): DISABLED 
SIP early-media for 180 responses with SDP: ENABLED
SIP max-forwards : 70
SIP DNS SRV version: 2 (rfc 2782)
NAT Settings for the SIP-UA
Role in SDP: NONE
Check media source packets: DISABLED
Maximum duration for a telephone-event in NOTIFYs: 2000 ms
SIP support for ISDN SUSPEND/RESUME: ENABLED
Redirection (3xx) message handling: ENABLED
Reason Header will override Response/Request Codes: DISABLED
Out-of-dialog Refer: DISABLED
Presence support is DISABLED
protocol mode is ipv6
SDP application configuration:
 Version line (v=) required
 Owner line (o=) required
 Timespec line (t=) required
 Media supported: audio video image 
 Network types supported: IN 
 Address types supported: IP4 IP6 
 Transport types supported: RTP/AVP udptl 


        
      


    














Configuring H.323 IPv4-to-SIPv6 Connections in a Cisco Unified Border Element


 
		
 An organization with an IPv4 network can deploy a Cisco Unified Border Element on the boundary to connect with the service provider's IPv6 network (see the figure below). 
		

 
		
Figure 2Cisco Unified Border Element Interoperating IPv4 Networks with IPv6 Service Provider


 
		   
		   
		

 
		
 A Cisco Unified Border Element can interoperate between H.323/SIP IPv4 and SIP IPv6 networks in media flow-through mode. In media flow-through mode, both signaling and media flows through the Cisco Unified Border Element, and the Cisco Unified Border Element performs both signaling and media interoperation between H.323/SIP IPv4 and SIP IPv6 networks (see the figure below). 
		

 
		
Figure 3IPv4 to IPv6 Media Interoperating Through Cisco IOS MTP


 
		   
		   
		

 
		
 The Cisco Unified Border Element feature adds IPv6 capability to existing VoIP features. This feature adds dual-stack support on voice gateways and MTP, IPv6 support for SIP trunks, and SCCP-controlled analog voice gateways. In addition, the SBC functionality of connecting SIP IPv4 or H.323 IPv4 network to a SIP IPv6 network is implemented on an Cisco Unified Border Element to facilitate migration from VoIPv4 to VoIPv6. 
		

 
		
 Perform this task to configure H.323 IPv4-to-SIPv6 connections in an Cisco Unified Border Element. 
		

 
	 


Before You Begin 
		
 Cisco Unified Border Element must be configured in IPv6-only or dual-stack mode to support IPv6 calls. 
		

 
		

Note
 
		  
 A Cisco Unified Border Element interoperates between H.323/SIP IPv4 and SIP IPv6 networks only in media flow-through mode. 
		  

 > 
		

 
	 

SUMMARY STEPS 
		
1.    
			  
				enable 
			  
		  

 
		
2.    
			  
				configure 
			  
			  
				terminal 
			  
		  

 
		
3.    
			  
				voice 
				service 
				voip 
			  
		  

 
		
4.    
			  
				allow-connections 
			  
			  
				from 
			  
			  
				type 
			  
			  
				to 
			  
			  
				to 
			  
			  
				type 
			  
		  

 
	 
DETAILED STEPS
 Command or ActionPurpose
 
		
Step 1
 
			  
				enable 
			  
		  
 

Example: 
			 

Router> enable

 
		   
  
			 
 Enables privileged EXEC mode. 
			 

 
			 
     
				
  •  Enter your password if prompted. 
				
    • 
 
			 

 
		   

 
		
Step 2
 
			  
				configure 
			  
			  
				terminal 
			  
		  
 

Example: 
			 

Router# configure terminal

 
		   
  
			 
 Enters global configuration mode. 
			 

 
		   

 
		
Step 3
 
			  
				voice 
				service 
				voip 
			  
		  
 

Example: 
			 

Router(config)# voice service voip

 
		   
  
			 
 Enters voice service VoIP configuration mode. 
			 

 
		   

 
		
Step 4
 
			  
				allow-connections 
			  
			  
				from 
			  
			  
				type 
			  
			  
				to 
			  
			  
				to 
			  
			  
				type 
			  
		  
 

Example: 
			 

Router(config-voi-serv)# allow-connections h323 to sip

 
		   
  
			 
 Allows connections between specific types of endpoints in a VoIPv6 network. 
			 

 
			 
 Arguments are as follows: 
			 

 
			 
     
				
  •  
				  from-type --Type of connection. Valid values: 
				  h323, 
				  sip. 
				
    • 
 
				
  •  
				  to-type --Type of connection. Valid values: 
				  h323, 
				  sip. 
				
    • 
 
			 

 
		   

 
	 












Configuring MTP Used with Voice Gateways


 
	 
 Cisco IOS MTP trusted relay point (TRP) supports media interoperation between IPv4 and IPv6 networks (see the figure below). This functionality is used when an IPv4 phone (registered to Cisco Unified Communications Manager, formerly known as Cisco Unified Call Manager) communicates with an IPv6 phone (registered to another Cisco Unified Communications Manager). In this case, one of the Cisco Unified Communications Managers inserts a Cisco IOS MTP to perform the IPv4-to-IPv6 media translation between the phones. 
	 

 
	 
 MTP for IPv4-to-IPv6 media translation operates only in dual-stack mode. Communication between Cisco IOS MTP and Cisco Unified Communications Manager occurs over SCCP for IPv4 only. 
	 

 
	 
Figure 4IPv4 to IPv6 Media Interoperating Through Cisco IOS MTP


 
		 
		 
	 

 
	 
 The VoIPv6 feature includes IPv4 and IPv6 dual-stack support on voice gateways and MTP, IPv6 support for SIP trunks, and SCCP-controlled analog phones. In addition, connecting a SIP IPv4 or H.323 IPv4 network to a SIP IPv6 network is implemented on Cisco Unified Border Element. 
	 

 
	 
 Perform this task to configure IPv6 with media interoperating using Cisco Unified Communications Manager-controlled MTP: 
	 

 
  


Restrictions



    
    
      
  • 
MTP for IPv4-to-IPv6 media translation operates in dual-stack mode only.
    • 

      
  • 
A SIP trunk can be configured over IPv4 only, over IPv6 only, or in dual-stack mode. In dual-stack mode, ANAT is used to describe both IPv4 and IPv6 media capabilities.
    • 

    


  










Configuring MTP for IPv4-to-IPv6 Translation



      

Perform this task to configure MTP for IPv4-to-IPv6 translation.


    

SUMMARY STEPS
      
1.   
          
            enable
          
        


      
2.   
          
            configure
          
          
            terminal
          
        


      
3.   
          
            sccp
            ccm
           {ipv4-address | ipv6-address | dns} identifier  identifier-number [priority priority] [port port-number] [version version-number]


      
4.   
          
            sccp
            ccm
            group
          
          
            group
          -number


      
5.   
          
            associate
            profile
          
          
            profile-identifier
          
          
            register
          
          
            device
          -name


      
6.   
          
            exit
          
        


      
7.   
          
            dspfarm
            profile
          
          
            profile
          -identifier {conference | mtp | transcode} [security]


      
8.   
          
            codec
           {codec-type | pass-through}


      
9.   
          
            maximum
            sessions
           {hardware | software} number


      
10.   
          
            associate
            application
            sccp
          
        


    
DETAILED STEPS
 Command or ActionPurpose

      
Step 1

          
            enable
          
        
 

Example:
          

Router> enable


         
 
          

Enables privileged EXEC mode. 


          
    
            
  • 
Enter your password if prompted.
    • 

          


         


      
Step 2

          
            configure
          
          
            terminal
          
        
 

Example:
          

Router# configure terminal


         
 
          

Enters global configuration mode.


         


      
Step 3

          
            sccp
            ccm
           {ipv4-address | ipv6-address | dns} identifier  identifier-number [priority priority] [port port-number] [version version-number]
 

Example:
          

Router(config)# sccp ccm 2001:DB8:C18:1::102 identifier 2 version 7.0


         
 
          

Adds a Cisco Unified CallManager server to the list of available servers and set various parameters--including IP address, IPv6 address, or Domain Name System (DNS) name, port number, and version number. 


          
Note   
SCCP communication between Cisco IOS MTP and Cisco Unified Border Element is supported only for an IPv4-only network. Do not use the ipv6-address
 argument with this command if you are configuring for the Cisco Unified Border Element. 


         


      
Step 4

          
            sccp
            ccm
            group
          
          
            group
          -number
 

Example:
          

Router(config)# sccp ccm group 1


         
 
          

Creates a Cisco CallManager group and enters SCCP Cisco CallManager configuration mode


         


      
Step 5

          
            associate
            profile
          
          
            profile-identifier
          
          
            register
          
          
            device
          -name
 

Example:
          

Router(conif-sccp-ccm)# associate profile 5 register MTP3825


         
 
          

Associates a digital signal processor (DSP) farm profile with a Cisco CallManager group.


         


      
Step 6

          
            exit
          
        
 

Example:
          

Router(config-sip-ua)# exit


         
 
          

Exits the current configuration mode.


         


      
Step 7

          
            dspfarm
            profile
          
          
            profile
          -identifier {conference | mtp | transcode} [security]
 

Example:
          

Router(config)# dspfarm profile 5 mtp 


         
 
          
Enters DSP farm profile configuration mode and defines a profile for DSP farm services.


         


      
Step 8

          
            codec
           {codec-type | pass-through}
 

Example:
          

Router(config-dspfarm-profile)# codec g711ulaw


         
 
          

Specifies the codecs that are supported by a DSP farm profile.


         


      
Step 9

          
            maximum
            sessions
           {hardware | software} number
 

Example:
          

Router(config-dspfarm-profile)# maximum sessions software 100	


         
 
          

Specifies the maximum number of sessions that are supported by the profile.


         


      
Step 10

          
            associate
            application
            sccp
          
        
 

Example:
          

Router(config-dspfarm-profile)# associate application SCCP


         
 
          

Associates SCCP to the DSP farm profile.


         


    














Configuring RTCP Pass-Phrough and T.38 Fax Support on the Cisco UBE for IPv6



    

Real-time control protocol (RTCP) pass-through and T.38 fax support on the Cisco Unified Border Element (Cisco UBE) for IPv6 provides support for RTCP pass-through and T.38-based fax calls on Cisco UBE for IPv6.


  


Restrictions



    
    
      
  • 
IPv4 and IPv6 addresses embedded within RTCP packets, for example RTCP CNAME, are passed on to Cisco UBE (ISR) without being masked. On the Cisco UBE ASR1000 these addresses are masked.
    • 

      
  • 
The Cisco UBE ASR 1000 does not support printing of RTCP debugs.
    • 

    


    

Note

RTCP is passed through by default; no configuration is required for RTCP pass-through.


  










Configuring T.38 Fax Globally



      

Perform this task to configure T.38 fax globally.


    

SUMMARY STEPS
      
1.   
          
            enable
          
        


      
2.   
          
            configure
          
          
            terminal
          
        


      
3.   
          
            voice
            service
          
          
            voip
          
        


      
4.   
          
            no
            ip
            address
            trusted
            authenticate
          
        


      
5.   
          
            allow-connections
           {h323 | sip} to {h323 | sip} 


      
6.   
          
            fax
            protocol
            t38
           [nse [force]] [version {0 | 3}] [ls-redundancy value [hs-redundancy value]] [fallback {cisco | none | pass-through {g711ulaw | g711alaw}}] 	


      
7.   
          
            sip
          
        


      
8.   
          
            bind
            control
            source-interface
          
          
            type
          
          
            number
          
        


      
9.   
          
            bind
            media
            source-interface
          
          
            type
          
          
            number
          
        


      
10.   
          
            no
            anat
          
        


      
11.   
          
            end
          
        


    
DETAILED STEPS
 Command or ActionPurpose

      
Step 1

          
            enable
          
        
 

Example:
          

Router> enable


         
 
          

Enables privileged EXEC mode. 


          
    
            
  • 
Enter your password if prompted.
    • 

          


         


      
Step 2

          
            configure
          
          
            terminal
          
        
 

Example:
          

Router# configure terminal


         
 
          

Enters global configuration mode.


         


      
Step 3

          
            voice
            service
          
          
            voip
          
        
 

Example:
          

Router(config)# voice service voip


         
 
          

Enters voice service configuration mode.


         


      
Step 4

          
            no
            ip
            address
            trusted
            authenticate
          
        
 

Example:
          

Router(conf-voi-serv)# no ip address trusted authenticate


         
 
          

Disables the IP address trusted authentication feature for incoming H.323 or SIP trunk calls for toll-fraud prevention.


         


      
Step 5

          
            allow-connections
           {h323 | sip} to {h323 | sip} 
 

Example:
          

Router(conf-voi-serv)# allow-connections sip to sip 


         
 
          

Allows connections between specific types of endpoints in a VoIP network.


         


      
Step 6

          
            fax
            protocol
            t38
           [nse [force]] [version {0 | 3}] [ls-redundancy value [hs-redundancy value]] [fallback {cisco | none | pass-through {g711ulaw | g711alaw}}] 	
 

Example:
          

Router(conf-voi-serv)# fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback cisco


         
 
          

Specifies the global default ITU-T T.38 standard fax protocol to be used for all VoIP dial peers.


         


      
Step 7

          
            sip
          
        
 

Example:
          

Router(conf-voi-serv)# sip


         
 
          

Enters SIP configuration mode.


         


      
Step 8

          
            bind
            control
            source-interface
          
          
            type
          
          
            number
          
        
 

Example:
          

Router(conf-serv-sip)# bind control source-interface GigabitEthernet 0/0


         
 
          

Binds Session Initiation Protocol (SIP) signaling packets and specifies an interface as the source address of SIP packets. 


         


      
Step 9

          
            bind
            media
            source-interface
          
          
            type
          
          
            number
          
        
 

Example:
          

Router(conf-serv-sip)# bind media source-interface GigabitEthernet 0/0


         
 
          

Binds only media packets to the IPv4 or IPv6 address of a specific interface and specifies an interface as the source address of SIP packets. 


         


      
Step 10

          
            no
            anat
          
        
 

Example:
          

Router(conf-serv-sip)# no anat 


         
 
          

Enables Alternative Network Address Types (ANAT) on a SIP trunk.


         


      
Step 11

          
            end
          
        
 

Example:
          

Router(conf-serv-sip)# end


         
 
          

Exits SIP configuration mode and returns to the privileged EXEC mode.


         


    












Configuring IPv6 Support for Cisco UBE



      

Perform this task to configure IPv6 support for Cisco UBE.


      

Note

        

In Cisco UBE, IPv4-only and IPv6-only modes are not supported when endpoints are dual-stack. In this case, Cisco UBE must also be configured in dual-stack mode.


>


    

SUMMARY STEPS
      
1.   
          
            enable
          
        


      
2.   
          
            configure
          
          
            terminal
          
        


      
3.   
          
            sip-ua
          
        


      
4.   
          
            protocol
            mode
           {ipv4 | ipv6 | dual-stack [preference {ipv4 | ipv6}]}


      
5.   
          
            end
          
        


    
DETAILED STEPS
 Command or ActionPurpose

      
Step 1

          
            enable
          
        
 

Example:
          

Router> enable


         
 
          

Enables privileged EXEC mode. 


          
    
            
  • 
Enter your password if prompted.
    • 

          


         


      
Step 2

          
            configure
          
          
            terminal
          
        
 

Example:
          

Router# configure terminal


         
 
          

Enters global configuration mode.


         


      
Step 3

          
            sip-ua
          
        
 

Example:
          

Router(config)# sip-ua


         
 
          

Enters SIP user-agent configuration mode.


         


      
Step 4

          
            protocol
            mode
           {ipv4 | ipv6 | dual-stack [preference {ipv4 | ipv6}]}
 

Example:
          

Router(config-sip-ua)# protocol mode ipv6


         
 
          

Configures the Cisco IOS SIP stack.


          
    
            
  • 
              
                protocol
                mode
              
              
                dual-stack
              
              
                preference
               {ipv4 | ipv6}--Sets the IP preference when the anat command is configured.
    • 

            
  • 
              
                protocol
                mode
               {ipv4 | ipv6}--Passes the IPv4 or IPv6 address in the SIP invite.
    • 

            
  • 
              
                protocol
                mode
              
              
                dual-stack
              --Passes both the IPv4 addresses and the IPv6 addresses in the SIP invite and sets priority based on the far-end IP address.
    • 

          


         


      
Step 5

          
            end
          
        
 

Example:
          

Router(config-sip-ua)# end


         
 
          

Exits SIP user-agent configuration mode.


         


    












Verifying RTCP Pass-Through



      

Perform this task to verify the RTCP pass-through support on Cisco UBE.


    

SUMMARY STEPS
      
1.   
          
            debug
            voip
            rtcp
            packets
          
        


    
DETAILED STEPS

      

        
          
            debug
            voip
            rtcp
            packets
          
        

         
          

Enables RTCP packet-related debugging.


          

Router# debug voip rtcp packets


        
         

Example:
          
*Feb 14 06:24:58.799: //1/xxxxxxxxxxxx/RTP//Packet/voip_remote_rtcp_packet: Received RTCP packet
*Feb 14 06:24:58.799: (src ip=2001:DB8:C18:5:21B:D4FF:FEDD:35F0, src port=17699,
 dst ip=2001:DB8:C18:5:21D:A2FF:FE72:4D00, dst port=17103)
*Feb 14 06:24:58.799: SR: ssrc=0x1F7A35F0 sr_ntp_h=0xD10346B4 sr_ntp_l=0x13173D8
F sr_timestamp=0x0 sr_npackets=381 sr_nbytes=62176
*Feb 14 06:24:58.799: RR: ssrc=0x1A1752F0 rr_loss=0x0 rr_ehsr=5748 rr_jitter=0 r
r_lsr=0x0 rr_dlsr=0x0
*Feb 14 06:24:58.799: SDES: ssrc=0x1F7A35F0 name=1 len=39 data=0.0.0@2001:DB8:C1
8:5:21B:D4FF:FEDD:35F0
*Feb 14 06:24:58.799: //2/xxxxxxxxxxxx/RTP//Packet/voip_remote_rtcp_packet: Send
ing RTCP packet
*Feb 14 06:24:58.799: (src ip=2001:DB8:C18:5:21D:A2FF:FE72:4D00, src port=23798,
 dst ip=2001:DB8:C18:5:21B:D4FF:FED7:52F0, dst port=19416)
*Feb 14 06:24:58.799: SR: ssrc=0x0 sr_ntp_h=0xD10346B4 sr_ntp_l=0x13173D8F sr_ti
mestamp=0x0 sr_npackets=381 sr_nbytes=62176
*Feb 14 06:24:58.799: RR: ssrc=0x1A1752F0 rr_loss=0x0 rr_ehsr=5748 rr_jitter=0 r
r_lsr=0x0 rr_dlsr=0x0
*Feb 14 06:24:58.799: SDES: ssrc=0x1F7A35F0 name=1 len=39 data=0.0.0@2001:DB8:C1
8:5:21B:D4FF:FEDD:35F0
*Feb 14 06:24:58.919:


        
      


    












Verifying T.38 Fax Configuration



      

Perform this task to verify the T.38 fax support on Cisco UBE. The show and debug commands need not be entered in any specific order.


    

SUMMARY STEPS
      
1.   
          
            enable
          
        


      
2.   
          
            debug
            ccsip
            all
          
        


      
3.   
          
            show
            call
            active
            voice
            compact
          
        


    
DETAILED STEPS

      
Step 1  
        
          
            enable
          
        

         
          

Enables privileged EXEC mode. 


        
         

Example:
          
Router> enable



        
      


      
Step 2  
        
          
            debug
            ccsip
            all
          
        

         
          

Enables all SIP-related debugging.


        
         

Example:
          
Router# debug ccsip all
Received:
INVITE sip:5555555555@[2001:DB8:1:1:1:1:1:1118]:5060 SIP/2.0
Via: SIP/2.0/UDP [2001:DB8:1:1:1:1:1:1115]:5060;branch=z9hG4bK83AE3
Remote-Party-ID: <sip:2222222222@[2001:DB8:1:1:1:1:1:1115]>;party=calling;screen=no;privacy=off
From: <sip:2222222222@[2001:DB8:1:1:1:1:1:1115]>;tag=627460F0-1259
To: <sip:5555555555@[2001:DB8:1:1:1:1:1:1118]>
Date: Tue, 01 Mar 2011 08:49:48 GMT
Call-ID: B30FCDEB-431711E0-8EDECB51-E9F6B1F1@2001:DB8:1:1:1:1:1:1115
Supported: 100rel,timer,resource-priority,replaces
Require: sdp-anat
Min-SE:  1800
Cisco-Guid: 2948477781-1125585376-2396638033-3925258737
User-Agent: Cisco-SIPGateway/IOS-15.1(3.14.2)PIA16
Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
CSeq: 101 INVITE
Max-Forwards: 70
Timestamp: 1298969388
Contact: <sip:2222222222@[22001:DB8:1:1:1:1:1:1115]:5060>
Expires: 180
Allow-Events: telephone-event
Content-Type: application/sdp
Content-Disposition: session;handling=required
Content-Length: 495
v=0
o=CiscoSystemsSIP-GW-UserAgent 7880 7375 IN IP6 2001:DB8:1:1:1:1:1:1115
s=SIP Call
c=IN IP6 2001:DB8:1:1:1:1:1:1115
t=0 0
a=group:ANAT 1 2
m=audio 17836 RTP/AVP 0 101 19
c=IN IP6 2001:DB8:1:1:1:1:1:1115
a=mid:1                                                
a=rtpmap:0 PCMU/8000
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-16
a=rtpmap:19 CN/8000
a=ptime:20
m=audio 18938 RTP/AVP 0 101 19
c=IN IP4 9.45.36.111
a=mid:2                                                
a=rtpmap:0 PCMU/8000
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-16
a=rtpmap:19 CN/8000
a=ptime:20
"Received: 
INVITE sip:2222222222@[2001:DB8:1:1:1:1:1:1117]:5060 SIP/2.0
Via: SIP/2.0/UDP [2001:DB8:1:1:1:1:1:1116]:5060;branch=z9hG4bK38ACE
Remote-Party-ID: <sip:5555555555@[2001:DB8:1:1:1:1:1:1116]>;party=calling;screen=no;privacy=off
From: <sip:5555555555@[2001:DB8:1:1:1:1:1:1116]>;tag=4FE8C9C-1630
To: <sip:2222222222@[2001:DB8:1:1:1:1:1:1117]>;tag=1001045C-992
Date: Thu, 10 Feb 2011 12:15:08 GMT
Call-ID: 5DEDB77E-ADC11208-808BE770-8FCACF34@2001:DB8:1:1:1:1:1:1117
Supported: 100rel,timer,resource-priority,replaces,sdp-anat
Min-SE:  1800
Cisco-Guid: 1432849350-0876876256-2424621905-3925258737
User-Agent: Cisco-SIPGateway/IOS-15.1(3.14.2)PIA16
Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
CSeq: 101 INVITE
Max-Forwards: 70
Timestamp: 1297340108
Contact: <sip:5555555555@[2001:DB8:1:1:1:1:1:1116]:5060>
Expires: 180
Allow-Events: telephone-event
Content-Type: application/sdp
Content-Length: 424
v=0
o=CiscoSystemsSIP-GW-UserAgent 8002 7261 IN IP6 2001:DB8:1:1:1:1:1:1116
s=SIP Call
c=IN IP6 2001:DB8:1:1:1:1:1:1116
t=0 0
m=image 17278 udptl t38
c=IN IP6 2001:DB8:1:1:1:1:1:1116
a=T38FaxVersion:0
a=T38MaxBitRate:14400
a=T38FaxFillBitRemoval:0
a=T38FaxTranscodingMMR:0
a=T38FaxTranscodingJBIG:0
a=T38FaxRateManagement:transferredTCF
a=T38FaxMaxBuffer:200
a=T38FaxMaxDatagram:320
a=T38FaxUdpEC:t38UDPRedundancy"



        
      


      
Step 3  
        
          
            show
            call
            active
            voice
            compact
          
        

         
          

Displays a compact version of call information. 


        
         

Example:
          
Router# show call active voice compact
<callID>  A/O FAX T<sec> Codec       type        Peer Address       IP R<ip>:<udp>
Total call-legs: 2
         9 ANS     T10      g711ulaw    VOIP        P2222222222 2208:......:1115:16808
        10 ORG     T10      g711ulaw    VOIP        P5555555555 2208:......:1116:17326


        
      


    
















Configuration Examples for Implementing VoIP over IPv6



  


Example  Configuring the SIP Trunk



    

      

This example shows how to configure the SIP trunk to use dual-stack mode, with IPv6 as the preferred mode. The SIP service must be shut down before any changes are made to protocol mode configuration.


      
Router(config)# sip-ua



      
Router(config-sip-ua)# protocol mode dual-stack preference ipv6


    


  










Example  Configuring the Source IPv6 Address of Signaling and Media Packets



    

      

This example shows how to configure the bind command:


      
Router(config)# voice service voip


      
Router(config-voi-serv)# sip


      

Router(config-serv-sip)# bind control source-interface FastEthernet 0/0


    


  










Example  Configuring the SIP Server



    

      

This example shows how to configure the SIP server:


      
Router(config)# sip-ua
Router(config-sip-ua)# sip-server ipv6:[2001:DB8:0:0:8:800:200C:417A]



    


  










Example  Configuring the Session Target



    

      

This example shows how to configure the session target:


      
Router(config)# dial-peer voice 29 voip


      
Router(config-dial-peer)# destination-pattern 7777


      
Router(config-dial-peer)# session target ipv6:[2001:DB8:0:0:8:800:200C:417A]


    


  










Example  Configuring SIP Register Support



    

      

This example shows how to configure SIP register support:


      
Router(config)# sip-ua


      
Router(config-sip-ua)# registrar ipv6:[2001:DB8:0:0:8:800:200C:417A] expires 3600 secondary 


      
Router(config-sip-ua)# retry register 10 


      
Router(config-sip-ua)# timers register 500 


    


  










Example  Configuring H.323 IPv4 to SIPv6 Connections in a Cisco Unified Border Element



    

      

This example shows how to configure H.323 IPv4 to IPv6 connections in an Cisco Unified Border Element.


      
Router(config)# voice service voip


      
Router(config-voi-serv)# allow-connections h323 to sip


    


  










Example  Configuring MTP for IPv4-to-IPv6 Translation



    

      

The following example shows how to configure MTP for IPv4-to-IPv6 translation and provides sample configuration output: 


      
Router(config)# sccp ccm group 1


      
Router(config-sccp-ccm)# associate profile 5 register MTP3825


      
Router(config-sccp-ccm)# exit


      
Router(config)# dspfarm profile 5 mtp 


      
Router(config-dspfarm-profile)# codec g711ulaw


      
Router(config-dspfarm-profile)# maximum sessions software 100


      
Router(config-dspfarm-profile)# associate application SCCP


      


      
Router# show sccp


      


      
sccp ccm group 1


      
associate profile 5 register MTP3825


      
!


      
dspfarm profile 5 mtp  


      
 codec g711ulaw


      
 maximum sessions software 100	


      
 associate application SCCP


    


  












Additional References


 
	 
 
	 

 
	 
Related Documents
 
		 
		

 
			  
			  
			  
				
 
				   
					 
 Related Topic
					 

 
				  		
 
				   
					 
 Document Title
					 

 
				  		
 
				

 
			 
 
			  
				
 
				   
					 
 Master Command Lists, All Releases
					 

 
				  		
 
				   
					 
 Master Command Lists
					 

 
				  		
 
				

 
				
 
				   
					 
 Cisco Express Forwarding for IPv6
					 

 
				  		
 
				   
					 
 " Implementing IPv6 Addressing and Basic Connectivity ," 
						Cisco IOS IPv6 Configuration Guide
					 

 
				  		
 
				

 
				
 
				   
					 
 IPv4-to-IPv6 media translation
					 

 
				  		
 
				   
					 
 " Configuring Cisco IOS Hosted NAT Traversal for Session Border Controller ," 
						Cisco IOS NAT Configuration Guide
					 

 
				  		
 
				

 
				
 
				   
					 
 Cisco IOS voice configuration
					 

 
				  		
 
				   
					 
 Cisco IOS Voice Configuration Library 
					 

 
				  		
 
				

 
				
 
				   
					 
 Cisco Unified Border Element configuration
					 

 
				  		
 
				   
					 
Cisco Unified Border Element Configuration Guide 
					 

 
				  		
 
				

 
				
 
				   
					 
 Cisco Unified Communications Manager
					 

 
				  		
 
				   
					 
 
						Cisco Unified Communications Manager 
					 

 
				  		
 
				

 
				
 
				   
					 
 Dual-stack information and configuration
					 

 
				  		
 
				   
					 
 " Implementing IPv6 Addressing and Basic Connectivity ," 
						Cisco IOS IPv6 Configuration Guide
					 

 
				  		
 
				

 
				
 
				   
					 
 IPv4 VoIP gateway
					 

 
				  		
 
				   
					 
 VoIP Gateway Trunk and Carrier Based Routing Enhancements 
					 

 
				  		
 
				

 
				
 
				   
					 
 VoIPv4 dial peer information and configuration
					 

 
				  		
 
				   
					 
 Dial Peer Features and Configuration 
					 

 
				  		
 
				

 
				
 
				   
					 
 SIP bind information
					 

 
				  		
 
				   
					 
 Configuring SIP Bind Features 
					 

 
				  		
 
				

 
				
 
				   
					 
 Basic H.323 gateway configuration
					 

 
				  		
 
				   
					 
 
						"Configuring H.323 Gateways," 
						 
						 
						  Cisco IOS Voice, Video, and Fax Configuration Guide 
						 
					 

 
				  		
 
				

 
				
 
				   
					 
 Basic H.323 gatekeeper configuration
					 

 
				  		
 
				   
					 
 
						Configuring H.323 Gatekeepers," 
						 
						 
						  Cisco IOS Voice, Video, and Fax Configuration Guide 
						 
					 

 
				  		
 
				

 
				
 
				   
					 
 IPv6 commands, including voice commands
					 

 
				  		
 
				   
					 
 
						Cisco IOS IPv6 Command Reference 
						
					 

 
				  		
 
				

 
				
 
				   
					 
 Troubleshooting and debugging guides
					 

 
				  		
 
				   
					 
 
				  
 
				

 
			 
 
		  



 
	 

 
	 
Standards
 
		 
		

 
			  
			  
			  
				
 
				   
					 
 Standard
					 

 
				  		
 
				   
					 
 Title
					 

 
				  		
 
				

 
			 
 
			  
				
 
				   
					 
 No new or modified standards are supported and support for existing standards has not been modified.
					 

 
				  		
 
				   
					 
 --
					 

 
				  		
 
				

 
			 
 
		  



 
	 

 
	 
MIBs
 
		 
		

 
			  
			  
			  
				
 
				   
					 
 MIB
					 

 
				  		
 
				   
					 
 MIBs Link
					 

 
				  		
 
				

 
			 
 
			  
				
 
				   
					 
 None
					 

 
				  		
 
				   
					 
 To locate and download MIBs for selected platforms, Cisco software releases, and feature sets, use Cisco MIB Locator found at the following URL:
					 

 
					 
 
						http://www.cisco.com/go/mibs 
					 

 
				  		
 
				

 
			 
 
		  



 
	 

 
	 
RFCs
 
		 
		

 
			  
			  
			  
				
 
				   
					 
 RFC
					 

 
				  		
 
				   
					 
 Title
					 

 
				  		
 
				

 
			 
 
			  
				
 
				   
					 
 RFC 3095
					 

 
				  		
 
				   
					 
 
						RObust Header Compression (ROHC): Framework and Four Profiles: RTP, UDP, ESP, and Uncompressed 
						 
					 

 
				  		
 
				

 
				
 
				   
					 
 RFC 3759
					 

 
				  		
 
				   
					 
 
						RObust Header Compression (ROHC): Terminology and Channel Mapping Examples 
						 
					 

 
				  		
 
				

 
				
 
				   
					 
 RFC 4091
					 

 
				  		
 
				   
					 
 
						The Alternative Network Address Types (ANAT) Semantics for the Session Description Protocol (SDP) Grouping Framework 
						 
					 

 
				  		
 
				

 
				
 
				   
					 
 RFC 4092
					 

 
				  		
 
				   
					 
 
						Usage of the Session Description Protocol (SDP) Alternative Network Address Types (ANAT) Semantics in the Session Initiation Protocol (SIP) 
						 
					 

 
				  		
 
				

 
			 
 
		  



 
	 

 
	 
Technical Assistance
 
		 
		

 
			  
			  
			  
				
 
				   
					 
 Description
					 

 
				  		
 
				   
					 
 Link
					 

 
				  		
 
				

 
			 
 
			  
				
 
				   
					 
 The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password. 
					 

 
				  		
 
				   
					 
 
						http://www.cisco.com/cisco/web/support/index.html 
					 

 
				  		
 
				

 
			 
 
		  



 
	 

 
  










Feature Information for Implementing VoIP for IPv6


 
	 
 
		
The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature. 
		

 
		
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to 
		  www.cisco.com/go/cfn. An account on Cisco.com is not required. 
		

 
	 


	 
 
		

Table 1Feature Information for Implementing VoIP for IPv6
 
		   
		   
		   
		   
			 
 
				 
				  
 Feature Name
				  

 
						
 
				 
				  
 Releases
				  

 
						
 
				 
				  
 Feature Information
				  

 
						
 
			 

 
		  
 
		   
			 
 
				 
				  
 VoIP for IPv6
				  

 
						
 
				 
				  
 12.4(22)T
				  

 
						
 
				 
				  
 VoIPv6 adds IPv6 capability to existing VoIP features. VoIPv6 requires IPv6 and IPv4 dual-stack support on voice gateways and MTP, IPv6 support for SIP trunks, and SCCP-controlled analog voice phones. In addition, the SBC functionality of connecting SIP IPv4 or H.323 IPv4 network to SIP IPv6 network is implemented on a Cisco Unified Border Element to facilitate migration from VoIPv4 to VoIPv6.
				  

 
						
 
			 

 
			 
 
				 
				  
 Cisco UBE RTCP voice pass-through for IPv6
				  

 
						
 
				 
				  
 15.2(1)T
				  

 
						
 
				 
				  
 RTCP pass-through on Cisco UBE adds IPv6 capability to the existing feature.
				  

 
				  
 No commands were introduced or modified.
				  

 
						
 
			 

 
			 
 
				 
				  
 T.38 Fax Support on Cisco UBE for IPv6
				  

 
						
 
				 
				  
 15.2(1)T
				  

 
						
 
				 
				  
 T.38 fax support on Cisco UBE adds IPv6 capability to the existing feature.
				  

 
				  
 No commands were introduced or modified.
				  

 
						
 
			 

 
		  
 
		



 
	 

 
  










 


 
	 
 
		
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: 
		  www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) 
		

 
		
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. 
		

 
	 

 
  














































































































































© 2012 Cisco Systems, Inc. All rights reserved.