IP SLAs Configuration Guide, Cisco IOS Release 15S - IPSLA Y1731 On-Demand and Concurrent Operations [Support]

Contents
IPSLA Y1731 On-Demand and Concurrent Operations
Finding Feature Information
Prerequisites for ITU-T Y.1731 Operations
Restrictions for IP SLAs Y.1731 On-Demand Operations
Information About IP SLAs Y.1731 On-Demand and Concurrent Operations
IPSLA Y1731 SLM Feature Enhancements
How to Configure IP SLAs Y.1731 On-Demand and Concurrent Operations
Configuring a Direct On-Demand Operation on a Sender MEP
Configuring a Referenced On-Demand Operation on a Sender MEP
Configuring an IP SLAs Y.1731 Concurrent Operation on a Sender MEP
Configuration Examples for IP SLAs Y.1731 On-Demand and Concurrent Operations
Example: On-Demand Operation in Direct Mode
Example: On-Demand Operation in Referenced Mode
Additional References for IP SLAs Y.1731 On-Demand and Concurrent Operations
Feature Information for IP SLAs Y.1731 On-Demand and Concurrent Operations
IPSLA Y1731 On-Demand and Concurrent Operations

This module describes how to configure the IPSLA Y1731 SLM Feature Enhancements feature for enabling real-time Ethernet service troubleshooting for users without configuration privileges. This feature supports on-demand Synthetic Loss Measurement (SLM) operations that can be run by issuing a single command in privileged EXEC mode.

Finding Feature Information
Prerequisites for ITU-T Y.1731 Operations
Restrictions for IP SLAs Y.1731 On-Demand Operations
Information About IP SLAs Y.1731 On-Demand and Concurrent Operations
How to Configure IP SLAs Y.1731 On-Demand and Concurrent Operations
Configuration Examples for IP SLAs Y.1731 On-Demand and Concurrent Operations
Additional References for IP SLAs Y.1731 On-Demand and Concurrent Operations
Feature Information for IP SLAs Y.1731 On-Demand and Concurrent Operations

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.

Prerequisites for ITU-T Y.1731 Operations

IEEE-compliant Connectivity Fault Management (CFM) must be configured and enabled for Y.1731 performance monitoring to function.

Restrictions for IP SLAs Y.1731 On-Demand Operations

SNMP is not supported for reporting threshold events or collecting performance statistics for on-demand operations.

On-demand operation statistics are not stored and are not supported by the statistic history and aggregation functions.

Information About IP SLAs Y.1731 On-Demand and Concurrent Operations
IPSLA Y1731 SLM Feature Enhancements

On-demand IP SLAs Synthetic Loss Measurement (SLM) operations, in the IPSLA Y1731 SLM Feature Enhancements feature, enable users without configuration access to perform real-time troubleshooting of Ethernet services. There are two operational modes for on-demand operations: direct mode that creates and runs an operation immediately and referenced mode that starts and runs a previously configured operation.
In the direct mode, a single command can be used to create multiple pseudo operations for a range of class of service (CoS) values to be run, in the background, immediately. A single command in privileged EXEC mode can be used to specify frame size, interval, frequency, and duration for the direct on-demand operation. Direct on-demand operations start and run immediately after the command is issued.

In the referenced mode, you can start one or more already-configured operations for different destinations, or for the same destination, with different CoS values. Issuing the privileged EXEC command creates a pseudo version of a proactive operation that starts and runs in the background, even while the proactive operation is running.

Once an on-demand operation is completed, statistical output is displayed on the console. On-demand operation statistics are not stored and are not supported by the statistic history and aggregation functions.

After an on-demand operation is completed, and the statistics handled, the direct and referenced on-demand operation is deleted. The proactive operations are not deleted and continue to be available to be run in referenced mode, again.

A concurrent operation consists of a group of operations, all configured with the same operation ID number, that run concurrently. Concurrent operations are supported for a given Ethernet Virtual Circuit (EVC), CoS, and remote Maintenance End Point (MEP) combination, or for multiple MEPs for a given multipoint EVC, for delay or loss measurements. A new keyword was added to the appropriate commands to specify that concurrent Ethernet frame Delay Measurement (ETH-DM) synthetic frames are sent during the operation.

The IPSLA Y.1731 SLM Feature Enhancements feature also supports burst mode for concurrent operations, one-way dual-ended, and single-ended delay and delay variation operations, as well as for single-ended loss operations. A new keyword was added to the appropriate commands to support bursts of PDU transmission during an aggregation interval. The maximum number of services monitored is 50 every 30 minutes, with an average of 25 services every 2 hours.

How to Configure IP SLAs Y.1731 On-Demand and Concurrent Operations
Configuring a Direct On-Demand Operation on a Sender MEP
Before You Begin
Class of Service (CoS)-level monitoring must be enabled on MEPs associated to the Ethernet frame loss operation by using the monitor loss counter command on the devices at both ends of the operation. See the Cisco IOS Carrier Ethernet Command Reference for command information. See the “Configuration Examples for IP SLAs Metro-Ethernet 3.0 (ITU-T Y.1731) Operations” section for configuration information.

Note

The Cisco IOS Y.1731 implementation allows monitoring of frame loss on an EVC regardless of the CoS value (any CoS or aggregate CoS cases). See the “Configuration Examples for IP SLAs Metro-Ethernet 3.0 (ITU-T Y.1731) Operations” section for configuration information.

SUMMARY STEPS
1. enable

2. ip sla on-demand ethernet {DMMv1 | SLM} domain domain-name {evc evc-id | vlan vlan-id} {mpid target-mp-id | mac-address target-address} cos cos {source {mpid source-mp-id | mac-address source-address}} {continuous [interval milliseconds] | burst [interval milliseconds] [number number-of-frames] [frequency seconds]} [size bytes] aggregation seconds {duration seconds | max number-of-packets}

DETAILED STEPS
Command or Action Purpose
Step 1
enable

Example:
Device> enable
          
Enables privileged EXEC mode.
Enter your password if prompted.
Step 2
ip sla on-demand ethernet {DMMv1 | SLM} domain domain-name {evc evc-id | vlan vlan-id} {mpid target-mp-id | mac-address target-address} cos cos {source {mpid source-mp-id | mac-address source-address}} {continuous [interval milliseconds] | burst [interval milliseconds] [number number-of-frames] [frequency seconds]} [size bytes] aggregation seconds {duration seconds | max number-of-packets}

Example:
Device# ip sla on-demand ethernet SLM domain xxx vlan 12 mpid 34 cos 4 source mpid 23 continuous aggregation 10 duration 60 
Creates and runs an on-demand operation in direct mode.
To create and run concurrent on-demand operations, configure this command using the DMMv1 keyword.

Statistical output is posted on the console after the operation is finished.

Repeat this step for each on-demand operation to be run.

After an on-demand operation is finished and the statistics handled, the operation is deleted.
Configuring a Referenced On-Demand Operation on a Sender MEP
Note
After an on-demand operation is finished and the statistics handled, the on-demand version of the operation is deleted.

Before You Begin

Single-ended and concurrent Ethernet delay, or delay variation, and frame loss operations to be referenced must be configured. See the “Configuring IP SLAs Metro-Ethernet 3.0 (ITU-T Y.1731) Operations” module of the IP SLAs Configuration Guide.

SUMMARY STEPS
1. enable

2. ip sla on-demand ethernet [dmmv1 | slm] operation-number {duration seconds | max number-of-packets

DETAILED STEPS
Command or Action Purpose
Step 1
enable

Example:
Device> enable
          
Enables privileged EXEC mode.
Enter your password if prompted.
Step 2
ip sla on-demand ethernet [dmmv1 | slm] operation-number {duration seconds | max number-of-packets

Example:
Device# ip sla on-demand ethernet slm 11 duration 38
Creates and runs a pseudo operation of the operation being referenced, in the background.
Statistical output is posted on the console after the operation is finished.

Repeat this step for each on-demand operation to be run.
Configuring an IP SLAs Y.1731 Concurrent Operation on a Sender MEP

To configure concurrent Ethernet delay, delay variation, and frame loss operations, see the “Configuring IP SLAs Metro-Ethernet 3.0 (ITU-T Y.1731) Operations” module of the
IP SLAs Configuration Guide.

Configuration Examples for IP SLAs Y.1731 On-Demand and Concurrent Operations
Example: On-Demand Operation in Direct Mode
Device# ip sla on-demand ethernet SLM domain xxx vlan 10 mpid 3 cos 1 source mpid 1 continuous aggregation 35 duration 38 

Loss Statistics for Y1731 Operation 2984884426
Type of operation: Y1731 Loss Measurement
Latest operation start time: *20:17:41.535 PST Wed May 16 2012
Latest operation return code: OK
Distribution Statistics:


Interval 1
 Start time:  *20:17:41.535 PST Wed May 16 2012
 End time:  *20:18:16.535 PST Wed May 16 2012
 Number of measurements initiated: 35
 Number of measurements completed: 35
 Flag: OK

Forward
  Number of Observations 3
  Available indicators: 0
  Unavailable indicators: 3
  Tx frame count: 30
  Rx frame count: 30
    Min/Avg/Max - (FLR % ): 0:9/000.00%/0:9
  Cumulative - (FLR % ): 000.00%
  Timestamps forward:
    Min - *20:18:10.586 PST Wed May 16 2012
    Max - *20:18:10.586 PST Wed May 16 2012
Backward
  Number of Observations 3
  Available indicators: 0
  Unavailable indicators: 3
  Tx frame count: 30
  Rx frame count: 30
    Min/Avg/Max - (FLR % ): 0:9/000.00%/0:9
  Cumulative - (FLR % ): 000.00%
  Timestamps backward:
    Min - *20:18:10.586 PST Wed May 16 2012
    Max - *20:18:10.586 PST Wed May 16 2012
Loss Statistics for Y1731 Operation 2984884426
Type of operation: Y1731 Loss Measurement
Latest operation start time: *20:17:41.535 PST Wed May 16 2012
Latest operation return code: OK
Distribution Statistics:


Interval 1
 Start time:  *20:17:41.535 PST Wed May 16 2012
 End time:  *20:18:16.535 PST Wed May 16 2012
 Number of measurements initiated: 35
 Number of measurements completed: 35
 Flag: OK

Forward
  Number of Observations 3
  Available indicators: 0
  Unavailable indicators: 3
  Tx frame count: 30
  Rx frame count: 30
    Min/Avg/Max - (FLR % ): 0:9/000.00%/0:9
  Cumulative - (FLR % ): 000.00%
  Timestamps forward:
    Min - *20:18:10.586 PST Wed May 16 2012
    Max - *20:18:10.586 PST Wed May 16 2012
Backward
  Number of Observations 3
  Available indicators: 0
  Unavailable indicators: 3
  Tx frame count: 30
  Rx frame count: 30
    Min/Avg/Max - (FLR % ): 0:9/000.00%/0:9
  Cumulative - (FLR % ): 000.00%
  Timestamps backward:
    Min - *20:18:10.586 PST Wed May 16 2012
    Max - *20:18:10.586 PST Wed May 16 2012
Example: On-Demand Operation in Referenced Mode
Device(config)# ip sla 11
Device(config-ip-sla)# ethernet y1731 loss SLM domain xxx vlan 10 mpid 3 cos 1 source mpid 1
Device(config-sla-y1731-loss)# end
Device# ip sla on-demand ethernet slm 11 duration 38

Loss Statistics for Y1731 Operation 2984884426
Type of operation: Y1731 Loss Measurement
Latest operation start time: *20:17:41.535 PST Wed May 16 2012
Latest operation return code: OK
Distribution Statistics:


Interval 1
 Start time:  *20:17:41.535 PST Wed May 16 2012
 End time:  *20:18:16.535 PST Wed May 16 2012
 Number of measurements initiated: 35
 Number of measurements completed: 35
 Flag: OK

Forward
  Number of Observations 3
  Available indicators: 0
  Unavailable indicators: 3
  Tx frame count: 30
  Rx frame count: 30
    Min/Avg/Max - (FLR % ): 0:9/000.00%/0:9
  Cumulative - (FLR % ): 000.00%
  Timestamps forward:
    Min - *20:18:10.586 PST Wed May 16 2012
    Max - *20:18:10.586 PST Wed May 16 2012
Backward
  Number of Observations 3
  Available indicators: 0
  Unavailable indicators: 3
  Tx frame count: 30
  Rx frame count: 30
    Min/Avg/Max - (FLR % ): 0:9/000.00%/0:9
  Cumulative - (FLR % ): 000.00%
  Timestamps backward:
    Min - *20:18:10.586 PST Wed May 16 2012
    Max - *20:18:10.586 PST Wed May 16 2012
Loss Statistics for Y1731 Operation 2984884426
Type of operation: Y1731 Loss Measurement
Latest operation start time: *20:17:41.535 PST Wed May 16 2012
Latest operation return code: OK
Distribution Statistics:


Interval 1
 Start time:  *20:17:41.535 PST Wed May 16 2012
 End time:  *20:18:16.535 PST Wed May 16 2012
 Number of measurements initiated: 35
 Number of measurements completed: 35
 Flag: OK

Forward
  Number of Observations 3
  Available indicators: 0
  Unavailable indicators: 3
  Tx frame count: 30
  Rx frame count: 30
    Min/Avg/Max - (FLR % ): 0:9/000.00%/0:9
  Cumulative - (FLR % ): 000.00%
  Timestamps forward:
    Min - *20:18:10.586 PST Wed May 16 2012
    Max - *20:18:10.586 PST Wed May 16 2012
Backward
  Number of Observations 3
  Available indicators: 0
  Unavailable indicators: 3
  Tx frame count: 30
  Rx frame count: 30
    Min/Avg/Max - (FLR % ): 0:9/000.00%/0:9
  Cumulative - (FLR % ): 000.00%
  Timestamps backward:
    Min - *20:18:10.586 PST Wed May 16 2012
    Max - *20:18:10.586 PST Wed May 16 2012


      
Additional References for IP SLAs Y.1731 On-Demand and Concurrent Operations

Related Documents

Related Topic

Document Title

Cisco IOS commands

Cisco IOS Master Commands List, All Releases

Cisco IOS IP SLAs commands

Cisco IOS IP SLAs Command Reference

Ethernet CFM for ITU-T Y.1731

“ITU-T Y.1731 Performance Monitoring in a Service Provider Network” module of the Carrier Ethernet Configuration Guide

Ethernet operations

“Configuring IP SLAs Metro-Ethernet 3.0 (ITU-T Y.1731) Operations” module of the IP SLAs Configuration Guide

Network Time Protocol (NTP)

“Configuring NTP” module of the Network Management Configuration Guide

Standards and RFCs

Standard/RFC

Title

ITU-T Y.1731

OAM functions and mechanisms for Ethernet-based networks

MIBs

MIB

MIBs Link

CISCO-IPSLA-ETHERNET-MIB

CISCO-RTTMON-MIB

To locate and download MIBs for selected platforms, Cisco software releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs

Technical Assistance

Description

Link

The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

http://www.cisco.com/cisco/web/support/index.html

Feature Information for IP SLAs Y.1731 On-Demand and Concurrent Operations

The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.

Table 1 Feature Information for IP SLAs Y.1731 On-Demand and Concurrent Operations
Feature Name

Releases

Feature Information

IPSLA Y1731 SLM Feature Enhancements

15.3(1)S

Cisco IOS XE Release 3.8S

This feature enhancement allows you to run on-demand Synthetic Loss Measurement (SLM) operations, independent from previously scheduled operations, for the purpose of troubleshooting Etherent services in your network.

In Cisco IOS XE Release 3.8S, support was added for the Cisco ASR 903 Router.

The following commands were introduced or modified: ethernet y1731 delay, ethernet y1737 loss, ip sla on-demand ethernet.