-
Asynchronous Transfer Mode Configuration Guide, Cisco IOS Release 12.4T
-
Configuring ATM
-
ATM OAM Ping
-
ATM OAM Support for F5 Continuity Check
-
ATM Policing by Service Category for SVC SoftPVC
-
Configuring ATM SNMP Trap and OAM Enhancements
-
ATM Multilink PPP Support on Multiple VCs
-
ATM Software Segmentation and Reassembly
-
ATM SVC Troubleshooting Enhancements
-
DHCP Client on WAN Interfaces
-
Lossless Compression and ATM Cell Switching and BITS Clocking
-
AAL1 CES on AIM-ATM
-
Enhanced Voice and QoS for ADSL and G.SHDSL
-
Unspecified Bit Rate Plus and ATM Enhancements
-
Multiprotocol over ATM Overview
-
MPLS Diff-Serv-aware Traffic Engineering over ATM
-
Configuring the Multiprotocol over ATM Client
-
Configuring the Multiprotocol over ATM Server
-
Configuring Token Ring LAN Emulation MPOA
-
LAN Emulation Overview
-
Configuring LAN Emulation
-
SNMP Trap Support for the Virtual Switch Interface Master MIB
-
Configuring Token Ring LAN Emulation
-
Feedback
Contents
ATM SVC Troubleshooting Enhancements
Finding Feature Information
Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the Feature Information Table at the end of this document.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
Feature Overview
The ATM SVC Troubleshooting Enhancements feature introduces two new debug commands: debug atm native and debug atm nmba. These commands can be used to troubleshoot ATM switched virtual circuits (SVCs). The debug atm nbmaand debug atm native commands are used to debug problems with Resource Reservation Protocol (RSVP) SVC creation and teardown. The debug atm nativecommand can also be used to debug problems with SVCs created using static maps.
Benefits
The ATM SVC Troubleshooting Enhancements feature provides two debug commands that can be used to troubleshoot ATM SVCs that were created using static maps or RSVP.
Supported Platforms
- Cisco 2600 series
- Cisco 3620
- Cisco 3631
- Cisco 3640
- Cisco 3660
- Cisco 3725
- Cisco 3745
- Cisco 7200 series
- Cisco 7500 series
- Cisco MC3810 series
- Universal Router Module (URM) for Cisco IGX 8400
Determining Platform Support Through Cisco Feature Navigator
Cisco IOS software is packaged in feature sets that support specific platforms. To get updated information regarding platform support for this feature, access Cisco Feature Navigator. Cisco Feature Navigator dynamically updates the list of supported platforms as new platform support is added for the feature.
Cisco Feature Navigator is a web-based tool that enables you to quickly determine which Cisco IOS software images support a specific set of features and which features are supported in a specific Cisco IOS image. You can search by feature or release. Under the release section, you can compare releases side by side to display both the features unique to each software release and the features in common.
To access Cisco Feature Navigator, you must have an account on Cisco.com. If you have forgotten or lost your account information, send a blank e-mail to cco-locksmith@cisco.com. An automatic check will verify that your e-mail address is registered with Cisco.com. If the check is successful, account details with a new random password will be e-mailed to you. Qualified users can establish an account on Cisco.com by following the directions at http://www.cisco.com/register .
Cisco Feature Navigator is updated regularly when major Cisco IOS software releases and technology releases occur. For the most current information, go to the Cisco Feature Navigator home page at the following URL:
Supported Standards and MIBs and and RFCs
MIBs
No new or modified MIBs are supported by this feature.
To obtain lists of supported MIBs by platform and Cisco IOS release, and to download MIB modules, go to the Cisco MIB website on Cisco.com at the following URL:
http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml
Monitoring and Maintaining ATM SVCs
To monitor and maintain RSVP SVCs or ATM SVCs that were created using static maps, use the following commands in privileged EXEC mode:
Command Reference
The following commands are introduced or modified in the feature or features documented in this module. For information about these commands, see the Cisco IOS Asynchronous Transfer Mode Command Reference. For information about all Cisco IOS commands, go to the Command Lookup Tool at http://tools.cisco.com/Support/CLILookup or to the Cisco IOS Master Commands List.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.