Cisco Nexus 6000 Series NX-OS Unicast Routing Command Reference
Show Commands
Downloads: This chapterpdf (PDF - 123.0KB) The complete bookPDF (PDF - 4.5MB) | Feedback

Show Commands

Table Of Contents

Show Commands

show ip rip

show ip rip interface

show ip rip neighbor

show ip rip policy statistics

show ip rip route

show ip rip statistics


Show Commands


This chapter describes the Cisco NX-OS Routing Information Protocol (RIP) show commands.

show ip rip

To display the configuration and status of the Routing Information Protocol (RIP), use the show ip rip command in any mode.

show ip rip [instance-tag] [vrf vrf-name]

Syntax Description

instance-tag

(Optional) RIP instance. The instance tag can be a maximum of 20 alphanumeric characters.

vrf vrf-name

(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-sensitive, alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.


Command Default

No default behavior or values

Command Modes

Any command mode

Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.


Examples

This example shows how to display the RIP configuration information:

switch(config-if)# show ip rip
 
   

Related Commands

Command
Description

show ip rip interface

Displays RIP information for an interface.

show ip rip neighbor

Displays RIP neighbor information.

show ip rip policy statistics

Displays RIP policy statistics.

show ip rip route

Displays RIP route information.

show ip rip statistics

Displays RIP statistics.


show ip rip interface

To display interface entry information from the Routing Information Protocol (RIP) topology table, use the show ip rip interface command in any mode.

show ip rip interface [type slot/port] [vrf vrf-name]

Syntax Description

interface type slot/port

(Optional) Specifies the interface.

vrf vrf-name

(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-sensitive, alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.


Command Default

This command has no default settings.

Command Modes

Any command mode

Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.


Examples

This example shows how to display the neighbor information for a specified interface from the RIP topology table:

switch(config-if)# show ip rip interface ethernet 1/2
 
   

Related Commands

Command
Description

show ip rip

Displays RIP information.

show ip rip neighbor

Displays RIP neighbor information.

show ip rip policy statistics

Displays RIP policy statistics.

show ip rip route

Displays RIP route information.

show ip rip statistics

Displays RIP statistics.


show ip rip neighbor

To display the neighbor information from the Routing Information Protocol (RIP) topology table, use the show ip rip neighbor command in any mode.

show ip rip neighbor [interface-type instance] [vrf vrf-name]

Syntax Description

interface-type

(Optional) Interface type. For more information, use the question mark (?) online help function.

instance

(Optional) Either a physical interface instance or a virtual interface instance.

vrf vrf-name

(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-sensitive, alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.


Command Default

No default behavior or values

Command Modes

Any command mode

Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.


Examples

The following is sample output from the show rip neighbor command:

switch(config-if)# show ip rip neighbor
 
   

Related Commands

Command
Description

show ip rip

Displays RIP information.

show ip rip interface

Displays RIP information for an interface.

show ip rip policy statistics

Displays RIP policy statistics.

show ip rip route

Displays RIP route information.

show ip rip statistics

Displays RIP statistics.


show ip rip policy statistics

To display the policy statistics for the Routing Information Protocol (RIP), use the show ip rip policy statistics command in any mode.

show ip rip policy statistics redistribute {bgp id | direct | eigrp id | ospf id | static} [vrf vrf-name]

Syntax Description

bgp

Displays policy statistics for the Border Gateway Protocol (BGP).

direct

Displays policy statistics for directly connected routes only.

eigrp

Displays policy statistics for Enhanced Interior Gateway Routing Protocol (EIGRP).

ospf

Displays policy statistics for Open Shortest Path First (OSPF) protocol.

static

Displays policy statistics for IP static routes.

id

For the bgp keyword, an autonomous system number. The range for 2-byte numbers is from 1 to 65535. The range for 4-byte numbers is from 1.0 to 65535.65535.

For the eigrp keyword, an EIGRP instance name from which routes are to be redistributed. The value takes the form of a string. You can enter a decimal number, but Cisco Nexus 6000 stores it internally as a string.

For the ospf keyword, an OSPF instance name from which routes are to be redistributed. The value takes the form of a string. You can enter a decimal number, but Cisco Nexus 6000 stores it internally as a string.

vrf vrf-name

(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-sensitive, alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.


Command Default

No default behavior or values.

Command Modes

Any command mode

Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.


Examples

This example shows how to show policy statistics for EIGRP:

switch# show ip rip policy statistics redistribute eigrp 201
 
   

Related Commands

Command
Description

clear ip rip policy statistics

Clears policy statistics for RIP.

show ip rip

Displays RIP information.

show ip rip interface

Displays RIP information for an interface.

show ip rip neighbor

Displays RIP information for a neighbor.

show ip rip route

Displays RIP route information.

show ip rip statistics

Displays RIP statistics.


show ip rip route

To display route information from the Routing Information Protocol (RIP) topology table, use the show ip rip route command in any mode.

show ip rip route [prefix/length] [summary] [vrf vrf-name]

Syntax Description

prefix/length

(Optional) IP prefix about which routing information should be displayed.

summary

(Optional) Displays information about summary routes.

vrf vrf-name

(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-sensitive, alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.


Command Default

No default behavior or values

Command Modes

Any command mode

Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.


Examples

This example shows how to display route information from the RIP topology table:

switch# show ip rip route
 
   

Related Commands

Command
Description

show ip rip

Displays RIP information.

show ip rip interface

Displays RIP information for an interface.

show ip rip neighbor

Displays RIP information for a neighbor.

show ip rip policy statistics

Displays policy statistics for RIP.

show ip rip statistics

Displays RIP statistics.


show ip rip statistics

To display statistical entry information from the Routing Information Protocol (RIP) topology table, use the show ip rip statistics command in any mode.

show ip rip statistics [interface-type instance] [vrf vrf-name]

Syntax Description

interface-type

(Optional) Interface type. For more information, use the question mark (?) online help function.

instance

(Optional) Either a physical interface instance or a virtual interface instance.

vrf vrf-name

(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-sensitive, alphanumeric string up to 32 characters. The strings "default" and "all" are reserved VRF names.


Command Default

No default behavior or values.

Command Modes

Any command mode

Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.


Examples

This example shows how to display the RIP statistics:

switch# show ip rip statistics
 
   

Related Commands

Command
Description

show ip rip

Displays RIP information.

show ip rip interface

Displays RIP information for an interface.

show ip rip neighbor

Displays RIP information for a neighbor.

show ip rip policy statistics

Displays policy statistics for RIP.

show ip rip route

Displays RIP route information.