Cisco Nexus 6000 Series NX-OS Unicast Routing Command Reference
Show Commands
Downloads: This chapterpdf (PDF - 117.0KB) The complete bookPDF (PDF - 4.5MB) | Feedback

Show Commands

Table Of Contents

Show Commands

show hsrp

show hsrp delay

show hsrp summary


Show Commands


This chapter describes the Cisco NX-OS Hot Standby Router Protocol (HSRP) show commands.

show hsrp

To display Hot Standby Router Protocol (HSRP) information for each HSRP group, use the show hsrp command.

show hsrp [interface {ethernet slot/port | port-channel number | vlan vlan-id}] [group group-number] [active | init | listen | standby] [all] [brief] [detail] [ipv4]

Syntax Description

interface

(Optional) Specifies the interface for which to display HSRP information.

ethernet slot/port

Specifies the Ethernet interface and the slot number and port number. The slot number is from 1 to 255, and the port number is from 1 to 128.

port-channel number

Specifies the EtherChannel interface and EtherChannel number. The range is from 1 to 4096.

vlan vlan-id

Specifies the VLAN interface. The range is from 1 to 4094.

group group-number

(Optional) Specifies the HSRP group number of the interface to display information about. The range is from 0 to 4095.

active

(Optional) Displays HSRP groups that are in an active state.

init

(Optional) Displays HSRP groups that are in an initialization state.

listen

(Optional) Displays HSRP groups that are in an listen state.

standby

(Optional) Displays HSRP groups that are in an standby state.

all

(Optional) Displays all HSRP groups.

brief

(Optional) Summarizes each virtual gateway or virtual forwarder with a single line of output.

detail

(Optional) Displays detailed information about HSRP groups.

ipv4

(Optional) Displays HSRP IPv4 groups.


Command Default

None

Command Modes

Any command mode

Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.


Usage Guidelines

Use the show hsrp command to display information about HSRP groups. The brief keyword displays a single line of information about each virtual gateway or virtual forwarder.

If you have not configured authentication, the show hsrp command will display the following string:

Authentication text "cisco"
 
   

This is the default behavior of HSRP as defined in RFC 2281:

If no authentication data is configured, the RECOMMENDED default
value is 0x63 0x69 0x73 0x63 0x6F 0x00 0x00 0x00.
 
   

This command does not require a license.


Note Make sure the LAN Base Services license is installed on the switch to enable Layer 3 interfaces.


Examples

This example shows how to display the default information about HSRP:

switch# show hsrp
Vlan1 - Group 1 (HSRP-V1) (IPv4)
  Local state is Active, priority 150 (Cfged 150), may preempt
    Forwarding threshold(for vPC), lower: 1 upper: 150
  Preemption Delay (Seconds) Reload:300
  Hellotime 3 sec, holdtime 10 sec
  Next hello sent in 0.793000 sec(s)
  Virtual IP address is 10.1.1.3 (Cfged)
  Active router is local
  Standby router is unknown
  Authentication text "cisco"
  Virtual mac address is 0000.0c07.ac01 (Default MAC)
  17 state changes, last state change 1w0d
  IP redundancy name is hsrp-Vlan1-1 (default)
...
 
   

Note The authentication text string in the preceding example indicates that authentication has not been configured on the interface.


This example shows how to display a brief summary of HSRP information:

switch# show hsrp brief
                     P indicates configured to preempt.
                     |
Interface   Grp Prio P State    Active addr      Standby addr     Group addr
Vlan1       1   150  P Active   local            unknown          10.1.1.3        (conf)
Vlan2       2   150  P Active   local            unknown          10.1.2.3        (conf)
...
 
   

Related Commands

Command
Description

feature hsrp

Enables the HSRP feature.


show hsrp delay

To display the Hot Standby Router Protocol (HSRP) group delay information, use the show hsrp delay command.

show hsrp delay [interface {ethernet slot/port | port-channel number[.sub_if_number] | vlan vlan_id}] [group group-number] [all] [brief]

Syntax Description

interface

(Optional) Specifies the interface type and number for which to display HSRP information.

ethernet slot/port

(Optional) Specifies the Ethernet interface. The slot number is from 1 to 255, and the port number is from 1 to 128.

port-channel number

(Optional) Specifies the EtherChannel interface. The EtherChannel number is from 1 to 4096.

.sub_if-number

(Optional) Subinterface number. The range is from 1 to 4093.

vlan vlan-id

(Optional) Specifies the VLAN interface. The range is from 1 to 4094.

group group-number

(Optional) Specifies the HSRP group number of the interface to display information about. The range is from 0 to 4095.

all

(Optional) Specifies all HSRP information.

brief

(Optional) Specifies brief HSRP information.


Command Default

None

Command Modes

Any command mode

Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.


Usage Guidelines

This command does not require a license.


Note Make sure the LAN Base Services license is installed on the switch to enable Layer 3 interfaces.


Examples

This example shows how to display HSRP delay information:

switch# show hsrp delay
---------------------------------
Interface       Minimum    Reload
---------------------------------
Eth1/5          30         0
switch#
 
   

Related Commands

Command
Description

delay minimum

Configures the delay infromation for HSRP groups.

feature hsrp

Enables the HSRP feature.

hsrp delay

Configures the delay infromation for HSRP groups.


show hsrp summary

To display Hot Standby Router Protocol (HSRP) summary information for each HSRP group, use the show hsrp summary command.

show hsrp summary

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.


Usage Guidelines

This command does not require a license.


Note Make sure the LAN Base Services license is installed on the switch to enable Layer 3 interfaces.


Examples

This example shows how to display a summary of HSRP information:

switch# show hsrp summary
 
   
HSRP Summary:
 
   
Extended-hold (NSF) disabled
Global HSRP-BFD disabled
 
   
Total Groups: 1
     Version::    V1-IPV4: 1       V2-IPV4: 0      V2-IPV6: 0
       State::     Active: 0       Standby: 0       Listen: 0
       State::  V6-Active: 0    V6-Standby: 0    V6-Listen: 0
 
   
Total HSRP Enabled interfaces: 1
 
   
Total Packets:
             Tx - Pass: 0       Fail: 0
             Rx - Good: 0
 
   
Packet for unknown groups: 0
 
   
Total MTS: Rx: 25
 
   
switch#
 
   

Related Commands

Command
Description

feature hsrp

Enables the HSRP feature.

hsrp

Configures HSRP groups.