ISDN數位使用者線路(IDSL)是未交換且不包含訊號(D通道)的租用線路ISDN基本速率介面(BRI)。IDSL和ISDN BRI使用相同的2B1Q線路調制。在路由器上,這等同於在租用線路配置中放置BRI介面。您可以將線路的速度配置為64 kbps、128 kbps或144 kbps。
通過線路傳輸的幀是標準的高級資料鏈路控制(HDLC)幀。您可以為租用線路BRI介面配置PPP或幀中繼封裝。將BRI介面視為以慢速運行的同步串列埠。
要使用IDSL,需要以下專案:
支援isdn leased-line全域性配置命令並具有BRI介面的路由器。
一種數字使用者線接入複用器(DSLAM),具有IDSL介面以終止連線的另一端。
目前,思科在Cisco 6160 DSLAM中使用八埠IDSL卡。計畫支援6130 DSLAM。不同之處在於,Cisco 6130僅支援每個IDSL卡四個埠。
與DSLAM配置匹配的速度和封裝。
IDSL DSLAM只有幾種型別。因此,很容易連線到其他供應商的裝置。
只有一個管道速度為64 kbps、128 kbps或144 kbps。
思科不支援通過通道化到兩個租用線路管道中的BRI介面。
本文中的資訊係根據以下軟體和硬體版本:
Cisco 804使用者端裝置(CPE)IOS ®軟體版本12.0(7)T
Cisco 6400 UAC節點路由處理器(NRP)IOS軟體版本12.0(7)DC
Cisco 6400 UAC節點交換處理器(NSP)IOS軟體版本12.0(4)DB
Cisco 6130 DSLAM-NI2 IOS軟體版本12.1(1)DA
本文中的資訊是根據特定實驗室環境內的裝置所建立。文中使用到的所有裝置皆從已清除(預設)的組態來啟動。如果您的網路正在作用,請確保您已瞭解任何指令可能造成的影響。
如需文件慣例的詳細資訊,請參閱思科技術提示慣例。
本節介紹如何為遠端使用者配置CPE。
本節提供可用於設定本檔案中所述功能的資訊。
注意:若要查詢有關本文檔中使用的命令的其他資訊,請使用命令查詢工具(僅限註冊客戶)。
本檔案會使用以下網路設定:
要為IDSL配置帶BRI介面的路由器,請完成以下步驟:
新增以下命令:
isdn leased-line bri [#] [128|144] ! interface bri [#] no shut !
此時線路會啟動,但線路協定不會啟動(如串列埠)。
不要發出show isdn status命令。它無關緊要,因為沒有D通道。有時,它會顯示第1層處於關閉狀態。
發出show int bri[#]命令,並根據線路協定和線路狀態遵循串列介面的規則。
新增PPP或幀中繼配置。
此示例顯示PPP配置:
isdn leased-line bri 0 128 ! username b-nrp password 0 cisco !--- b-nrp is the username assigned to the ISDN router !--- to authenticate with the ISP. !--- cisco is the password assigned to the ISDN router !--- to authenticate with the ISP. ! ! interface BRI0 ip address 7.7.7.2 255.255.255.0 encapsulation ppp ppp authentication chap !
這兩個示例顯示了幀中繼配置。確保使用Internet工程任務組(IETF)封裝。
範例 1
! interface BRI0/0 ip address 10.0.0.1 255.255.255.0 no ip directed-broadcast encapsulation frame-relay IETF fair-queue 64 16 0 frame-relay map ip 10.0.0.2 300 broadcast IETF frame-relay lmi-type ansi !
範例 2
! interface BRI0/0 no ip address no ip directed-broadcast encapsulation frame-relay IETF fair-queue 64 16 0 frame-relay lmi-type ansi ! interface BRI0/0.300 point-to-point ip address 10.0.0.2 255.255.255.0 no ip directed-broadcast frame-relay interface-dlci 300 IETF !
注意:請記住,沒有訊號、撥號程式介面、撥號程式清單、撥號程式字串以及撥號程式對映。這是一條專用線路,類似於專用的T1串列線路。唯一的區別是使用2B1Q調制代替用於資料服務單元/通道服務單元(DSU/CSU)的V.35。
如果PPP未啟動線路協定,請發出以下debug命令:
debug ppp negotiation
debug ppp authentication
debug ppp error
NI2 DSLAM組態假設瞭解DSL和ATM組態,包括使用ATM的PPP(PPPoA)。 IDSL配置比非對稱數字使用者線路(ADSL)或單線數字使用者線路(SDSL)設定更深入。
要在DSLAM中使用IDSL卡,必須使用Cisco IOS軟體版本12.1(2)DA或更高版本。
在DSLAM上,ADSL和SDSL介面在配置中顯示為ATM介面。Cisco的ADSL和SDSL實施使用ATM。但是,IDSL使用HDLC幀來傳輸資料。因此,介面在配置中顯示為IDSL介面。
對於Cisco 6160 DSLAM中的一個IDSL卡,配置類似於以下輸出:
! interface IDSL3/1 no ip address no logging event link-status no arp frame-relay ! interface IDSL3/2 no ip address no logging event link-status no arp frame-relay ! interface IDSL3/3 no ip address no logging event link-status no arp frame-relay ! interface IDSL3/4 no ip address no logging event link-status no arp frame-relay ! interface IDSL3/5 no ip address no logging event link-status no arp frame-relay ! interface IDSL3/6 no ip address no logging event link-status no arp frame-relay ! interface IDSL3/7 no ip address no logging event link-status no arp frame-relay ! interface IDSL3/8 no ip address no logging event link-status no arp frame-relay !
注意:NI1 DSLAM平台不支援IDSL,並且不計畫提供此支援。
每個IDSL介面都有一個偽ATM介面。在硬體上,HDLC幀在NI2 ATM交換矩陣交換之前會轉換為ATM信元。
對於PPP,定義具有目標虛擬路徑識別符號(VPI)和虛擬通道識別符號(VCI)的永久虛擬電路(PVC)。源VCI/VPI不是必需的,因為PPP只有一個連線。
對於幀中繼,請設定16個PVC,它們將轉換為16個資料鏈路連線識別符號(DLCI)。 此配置涉及提供源DLCI編號和目標VPI/VCI對。
DSL配置有兩個主要步驟。對於PPP配置,它們是:
設定IDSL DSL配置檔案。
在IDSL介面下設定PVC/SVC。
此外,請為IDSL鏈路設定服務品質(QoS),以便正確使用轉到IDSL埠的ATM資源。計算ATM成幀的開銷。下表顯示需要為等效IDSL位元率配置的最大ATM峰值信元速率/可持續信元速率(PCR/SCR)。
已配置IDSL位元率(kbps) | 最大ATM PCR/SCR(kbps) |
---|---|
56 | 71 |
64 | 81 |
128 | 163 |
144 | 183 |
以下PPP選項可用於IDSL配置檔案:
idsl bitrate [56 | 64 | 128 | 144] idsl encapsulation [cisco-ppp | llc-ppp | mux-ppp ]
位元率必須與CPE的位元率匹配。封裝指定在聚合器終止的PPPoA封裝型別。
以下語法用於建立連線到IDSL PPP終端的PVC:
ppp pvc interface atm 0/x [VPI] [VCI]
沒有輸入PVC,因為PPP鏈路只有一個連線。ATM 0/x是從DSLAM到聚合器的ATM管道。
要設定QoS引數,請使用此全域性命令。使用PCR/SCR表來檢視pcr和scr10值。
atm connection-traffic-table-row index [row #] vbr-nrt pcr [#] scr10 [#]
若要將這些值應用於IDSL PVC,請將ppp pvc interface atm 0/x [VPI] [VCI]更改為ppp pvc interface atm 0/x [VPI] [VCI] rx-cttr [row #] tx-cttr [row #] 。
使用128 Kbps和llc-ppp封裝到聚合器的PPP IDSL配置如下:
atm connection-traffic-table-row index 128 vbr-nrt pcr 163 scr10 163 ! dsl-profile idsl1 idsl encapsulation llc-ppp !--- 128 kbps is the default. ! ! interface IDSL3/1 dsl profile idsl1 ppp pvc interface ATM0/1 3 300 rx-cttr 128 tx-cttr 128 !
如果DSLAM是在IDSL配置檔案下為encapsulation llc-ppp配置的(或者沒有為封裝設定任何內容,因為這是預設設定),則聚合器需要具有以下配置:
! interface ATM0/0/0.300 point-to-point no ip directed-broadcast pvc 3/300 encapsulation aal5snap protocol ppp Virtual-Template10 ! !
如果為encapsulation cisco-ppp配置了DSLAM,請將配置更改為:
! interface ATM0/0/0.300 point-to-point no ip directed-broadcast pvc 3/300 encapsulation aal5ciscoppp Virtual-Template10 ! !
如果為IDSL encapsulation mux-ppp配置了DSLAM,請確保聚合器上的配置為:
! interface ATM0/0/0.300 point-to-point no ip directed-broadcast pvc 3/300 encapsulation aal5mux ppp Virtual-Template10 ! !
對於幀中繼配置,兩個主要步驟與PPP配置中的步驟相同。
設定IDSL DSL配置檔案。
在IDSL介面下設定PVC/SVC。
對於幀中繼鏈路上的QoS,無需進行特殊轉換。在connection-table-row中設定最大速率,使其與CPE上定義的頻寬相匹配。
對於IDSL配置檔案,以下為幀中繼選項:
idsl bitrate [56 | 64 | 128 | 144] idsl frame-relay ? bc-default Default Bc in bytes lmi-n392dce LMI error threshold lmi-n393dce set LMI monitored event count lmi-t392dce set DCE polling verification timer lmi-type Use CISCO-ANSI-CCITT type LMI upc-intent UPC to use on Soft-VCs/PVCs
要啟用幀中繼封裝,還必須新增idsl encapsulation frame-relay命令。
此語法建立連線到IDSL幀中繼終端的PVC:
frame-relay pvc [DLCI] service translation interface atm0/1 [VPI] [VCI]
還有一個透明引數未在本文檔中討論。translation關鍵字將定義的幀中繼DLCI轉換為定義的ATM PVC。ATM PVC是AAL5SNAP PVC。
要設定QoS引數,請使用以下全域性命令:
frame-relay connection-traffic-table-row index [row #] [CIR] [Burst] [PIR] vbr-rt
通常,CIR=PIR等於鏈路的IDSL配置檔案中定義的頻寬。突發速率通常最大為32,768 bps。
若要將這些值應用於IDSL PVC,請將frame-relay pvc [DLCI]服務轉換介面atm0/1 [VPI] [VCI]更改為frame-relay pvc [DLCI] rx-cttr [Row #] tx-cttr [Row #] service translation interface atm0/1 [VPI] [VCI]。
使用128 Kbps和lmi-type ANSI的幀中繼IDSL配置為:
! dsl-profile idslframe idsl encapsulation frame-relay idsl frame-relay lmi-type ansi ! frame-relay connection-traffic-table-row index 128 128000 32768 128000 vbr-rt ! ! interface IDSL2/2 no ip address dsl profile idslframe no arp frame-relay frame-relay pvc 300 rx-cttr 128 tx-cttr 128 service translation interface ATM0/1 3 300 !
對於CPE端的幀中繼封裝,DSLAM將幀中繼PVC轉換為ATM PVC。ATM PVC封裝在AAL5SNAP中。
對於路由幀中繼PVC:
! interface ATM0/0/0.300 point-to-point ip address 10.0.0.1 255.255.255.0 pvc 3/300 encapsulation aal5snap protocol ip (inarp) broadcast ! !
與插入DSLAM機箱中的其它卡類似,可能需要在NI2配置中手動指定IDSL卡。
DSLAM(config)#slot 2 ituc-1-8IDSL
插入IDSL卡後,發出show oir status命令以顯示下載到卡的代碼的狀態。
DSLAM#show oir status 2 Slot 2: timer stopped delay 100 last heard 30348 ms ago, last sent 30348 ms ago Slot 2: loading. . . current offset 0x1CFD1, done at 0xBF858
出現此日誌輸出。
00:04:20: %SLOT-3-MODULE_DETECTED: CLEAR INFO Slot 2 Module was detected 00:04:45: %SLOT-3-MODULE_MISSING: CLEAR MAJOR Slot 2 Provisioned slot is empty 00:04:45: %SLOT-3-MODULE_DETECTED: ASSERT INFO Slot 2 Module was detected 00:04:48: %LINK-3-UPDOWN: Interface IDSL2/1 to IDSL2/8, changed state to down DSLAM#show hardware Chassis Type: C6160 Slot 1 : STUC-4-2B1Q-DIR-1 Slot 18: EMPTY Slot 2 : ITUC-1-8IDSL Slot 19: EMPTY Slot 3 : EMPTY Slot 20: EMPTY Slot 4 : EMPTY Slot 21: EMPTY Slot 5 : EMPTY Slot 22: EMPTY Slot 6 : EMPTY Slot 23: EMPTY Slot 7 : EMPTY Slot 24: EMPTY Slot 8 : EMPTY Slot 25: EMPTY Slot 9 : EMPTY Slot 26: EMPTY Slot 10: NI-2-155SM-DS3 Slot 27: EMPTY Slot 11: EMPTY Slot 28: EMPTY Slot 12: EMPTY Slot 29: EMPTY Slot 13: EMPTY Slot 30: EMPTY Slot 14: EMPTY Slot 31: EMPTY Slot 15: EMPTY Slot 32: EMPTY Slot 16: EMPTY Slot 33: EMPTY Slot 17: EMPTY Slot 34: EMPTY Fan Module: Present Power Supply Module 1: Present 2: Not Present
本節提供的資訊用於對組態進行疑難排解。
輸出直譯器工具(僅供註冊客戶使用)支援某些show命令,此工具可讓您檢視show命令輸出的分析。
注意:發出debug指令之前,請參閱有關Debug指令的重要資訊。
debug ppp negotiation — 監視PPP協商事件。
debug ppp authentication — 確定客戶端是否通過身份驗證。
show dsl interface idsl 2/2 — 顯示IDSL和連線統計資訊。
show atm vc interface — 顯示IDSL介面後面的偽ATM介面。
show users — 顯示有關活動使用者的資訊。
若要對IDSL PPP連線進行故障排除,請發出debug ppp negotiation和debug ppp authentication命令。對於活動連線,這是show users命令的輸出
Router#show users Line User Host(s) Idle Location * 0 con 0 idle 00:00:00 Interface User Mode Idle Peer Address BR0/0 b-nrp Sync PPP 00:00:03 10.0.0.2
在DSLAM上,這些命令顯示IDSL統計資訊和連線統計資訊。
DSLAM#show dsl interface idsl 2/2 Port Status: Subscriber Name: Circuit ID: IOS admin: UP oper: UP Card status: ITUC-1-8IDSL Last Change: 00 days, 00 hrs, 07 min, 13 sec No. of changes: 1 Loopback: none Firmware version: 961170635 BERT has not been executed on this interface Configured: Profile Name: default Alarms Enabled: NO IDSL profile parameters Bitrate: 128 kbit/sec Encapsulation: llc-ppp Frame Relay parameters: UPC intent: pass Bc default: 32768 bytes LMI type: cisco lmi-n392dce: 2 events lmi-n393dce: 2 events lmi-t392dce: 15 seconds Performance Statistics: Physical layer Coding violations : 0 Errored seconds : 0 Severely errored seconds : 0 Physical layer (far end) Coding violations : 0 Errored seconds : 0 Severely errored seconds : 0 HDLC layer Coding violations : 0 Aborts : 0 Aligns : 0 Shorts : 5 Longs : 0 Discards : 42 Alarm Status: NONE
請注意,每個IDSL介面後面都有一個關聯的偽ATM介面。
DSLAM#show atm vc interface atm-p 2/2 Interface VPI VCI Type X-Interface X-VPI X-VCI Encap Status ATM-P2/2 0 37 PVC ATM0/1 3 300 UP DSLAM#show atm vc interface atm-p 2/2 0 37 Interface: ATM-P2/2, Type: ATM-PSEUDO VPI = 0 VCI = 37 Status: UP Time-since-last-status-change: 00:02:24 Connection-type: PVC Cast-type: point-to-point Packet-discard-option: disabled Usage-Parameter-Control (UPC): pass Number of OAM-configured connections: 0 OAM-configuration: disabled OAM-states: Not-applicable Cross-connect-interface: ATM0/1, Type: suni_dual Cross-connect-VPI = 3 Cross-connect-VCI = 300 Cross-connect-UPC: pass Cross-connect OAM-configuration: disabled Cross-connect OAM-state: Not-applicable Rx cells: 27, Tx cells: 0 Rx connection-traffic-table-index: 128 Rx service-category: VBR-NRT (Non-Realtime Variable Bit Rate) Rx pcr-clp01: 163 Rx scr-clp01: 163 Rx mcr-clp01: none Rx cdvt: none Rx mbs: 1024 (from default for interface) Tx connection-traffic-table-index: 128 Tx service-category: VBR-NRT (Non-Realtime Variable Bit Rate) Tx pcr-clp01: 163 Tx scr-clp01: 163 Tx mcr-clp01: none Tx cdvt: none Tx mbs: none
您也可以從另一端(從聚合器到CPE)檢視PVC。
DSLAM#show atm vc interface atm 0/1 3 300 Interface: ATM0/1, Type: suni_dual VPI = 3 VCI = 300 Status: UP Time-since-last-status-change: 00:03:20 Connection-type: PVC Cast-type: point-to-point Packet-discard-option: disabled Usage-Parameter-Control (UPC): pass Number of OAM-configured connections: 0 OAM-configuration: disabled OAM-states: Not-applicable Cross-connect-interface: ATM-P2/2, Type: ATM-PSEUDO Cross-connect-VPI = 0 Cross-connect-VCI = 37 Cross-connect-UPC: pass Cross-connect OAM-configuration: disabled Cross-connect OAM-state: Not-applicable Rx cells: 0, Tx cells: 68 Rx connection-traffic-table-index: 128 Rx service-category: VBR-NRT (Non-Realtime Variable Bit Rate) Rx pcr-clp01: 163 Rx scr-clp01: 163 Rx mcr-clp01: none Rx cdvt: none Rx mbs: 1024 (from default for interface) Tx connection-traffic-table-index: 128 Tx service-category: VBR-NRT (Non-Realtime Variable Bit Rate) Tx pcr-clp01: 163 Tx scr-clp01: 163 Tx mcr-clp01: none Tx cdvt: none Tx mbs: none
本節提供的資訊可用於對組態進行疑難排解。
輸出直譯器工具(僅供註冊客戶使用)支援某些show命令,此工具可讓您檢視show命令輸出的分析。
注意:發出debug指令之前,請參閱有關Debug指令的重要資訊。
show frame lmi — 顯示有關本地管理介面(LMI)的統計資訊。
debug frame lmi — 確定是否正確傳送和接收LMI資料包。
show frame-relay pvc — 顯示幀中繼介面的PVC統計資訊。
show frame map — 顯示當前對映條目和有關連線的資訊。
show frame-relay interface resource — 顯示QoS引數。
show interface idsl — 顯示幀中繼統計資訊。
show atm vc interface — 顯示IDSL介面後面的偽ATM介面。
要排除IDSL BRI埠連線故障,請使用用於排除串列埠故障的相同命令。
Router#show frame lmi !--- Check for status messages received and Enq. sent. LMI Statistics for interface BRI0/0 (Frame Relay DTE) LMI TYPE = CISCO Invalid Unnumbered info 0 Invalid Prot Disc 0 Invalid dummy Call Ref 0 Invalid Msg Type 0 Invalid Status Message 0 Invalid Lock Shift 0 Invalid Information ID 0 Invalid Report IE Len 0 Invalid Report Request 0 Invalid Keep IE Len 0 Num Status Enq. Sent 71 Num Status msgs Rcvd 0 Num Update Status Rcvd 0 Num Status Timeouts 70
超時表示沒有來自NI2交換機的通訊。
若要偵錯,請以與用於序列介面相同的方式發出debug frame lmi命令。您也可以發出show frame-relay pvc和show frame map命令。
Router#show frame lmi LMI Statistics for interface BRI0/0 (Frame Relay DTE) LMI TYPE = ANSI Invalid Unnumbered info 0 Invalid Prot Disc 0 Invalid dummy Call Ref 0 Invalid Msg Type 0 Invalid Status Message 0 Invalid Lock Shift 0 Invalid Information ID 0 Invalid Report IE Len 0 Invalid Report Request 0 Invalid Keep IE Len 0 Num Status Enq. Sent 17 Num Status msgs Rcvd 18 Num Update Status Rcvd 0 Num Status Timeouts 0 Router#show frame-relay pvc PVC Statistics for interface BRI0/0 (Frame Relay DTE) Active Inactive Deleted Static Local 1 0 0 0 Switched 0 0 0 0 Unused 0 0 0 0 DLCI = 300, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = BRI0/0 input pkts 0 output pkts 0 in bytes 0 out bytes 0 dropped pkts 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 0 out bcast bytes 0 pvc create time 00:02:30, last time pvc status changed 00:02:30 Router#show frame map BRI0/0 (up): ip 10.0.0.2 dlci 300(0x12C,0x48C0), static, broadcast, IETF, status defined, active
在DSLAM端,您還可以發出show frame lmi命令。
DSLAM#show frame-relay lmi interface idsl2/2 LMI Statistics for interface IDSL2/2 (Frame Relay DCE) LMI TYPE = ANSI Invalid Unnumbered info 0 Invalid Prot Disc 0 Invalid dummy Call Ref 0 Invalid Msg Type 0 Invalid Status Message 0 Invalid Lock Shift 0 Invalid Information ID 0 Invalid Report IE Len 0 Invalid Report Request 0 Invalid Keep IE Len 0 Num Status Enq. Rcvd 2 Num Status msgs Sent 2 Num Update Status Sent 0 Num St Enq. Timeouts 0
若要檢視QoS引數,請發出show frame-relay interface resource命令。
DSLAM#show frame-relay interface resource idSL 2/1 Encapsulation: FRAME-RELAY Resource Management state: Available bit rates (in bps): 128000 vbr-nrt RX, 128000 vbr-nrt TX 128000 vbr-rt RX, 128000 vbr-rt TX 128000 ubr RX, 128000 ubr TX Allocated bit rates (in bps): 0 vbr-nrt RX, 0 vbr-nrt TX 0 vbr-rt RX, 0 vbr-rt TX 0 ubr RX, 0 ubr TX
當介面配置為幀中繼模式時,發出show interface idsl命令以顯示幀中繼統計資訊。
DSLAM#show interface idsl2/2 IDSL2/2 is up, line protocol is up Hardware is idsl MTU 1500 bytes, BW 128 Kbit, DLY 0 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY IETF, loopback not set Keepalive set (10 sec) LMI enq sent 0, LMI stat recvd 0, LMI upd recvd 0 LMI enq recvd 8, LMI stat sent 8, LMI upd sent 0, DCE LMI up LMI DLCI 0 LMI type is ANSI Annex D frame relay DCE Broadcast queue 0/64, broadcasts sent/dropped 0/0, interface broadcasts 0 Last input 00:00:03, output 00:00:03, output hang never Last clearing of "show interface" counters 00:01:20 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 8 packets input, 112 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 8 packets output, 117 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out 0 carrier transitions DSLAM#show dsl interface idsl 2/2 Port Status: Subscriber Name: Circuit ID: IOS admin: UP oper: UP Card status: ITUC-1-8IDSL Last Change: 00 days, 00 hrs, 06 min, 09 sec No. of changes: 64 Loopback: none Firmware version: 961170635 BERT has not been executed on this interface Configured: Profile Name: idslframe Alarms Enabled: NO IDSL profile parameters Bitrate: 128 kbit/sec Encapsulation: frame-relay Frame Relay parameters: UPC intent: pass Bc default: 32768 bytes LMI type: ansi lmi-n392dce: 2 events lmi-n393dce: 2 events lmi-t392dce: 15 seconds Performance Statistics: Physical layer Coding violations : 0 Errored seconds : 0 Severely errored seconds : 0 Physical layer (far end) Coding violations : 0 Errored seconds : 0 Severely errored seconds : 0 HDLC layer Coding violations : 0 Aborts : 0 Aligns : 0 Shorts : 0 Longs : 0 Discards : 0 Alarm Status: NONE DSLAM#show atm vc interface atm-p 2/2 Interface VPI VCI Type X-Interface X-VPI X-VCI Encap Status ATM-P2/2 0 37 PVC ATM0/1 3 300 UP DSLAM#show atm vc interface atm-p 2/2 0 37 Interface: ATM-P2/2, Type: ATM-PSEUDO VPI = 0 VCI = 37 Status: UP Time-since-last-status-change: 00:06:59 Connection-type: PVC Cast-type: point-to-point Packet-discard-option: disabled Usage-Parameter-Control (UPC): pass Number of OAM-configured connections: 2 OAM-configuration: Ais-on OAM-states: OAM-Up OAM-Loopback-Tx-Interval: 5 Cross-connect-interface: ATM0/1, Type: suni_dual Cross-connect-VPI = 3 Cross-connect-VCI = 300 Cross-connect-UPC: pass Cross-connect OAM-configuration: Ais-on Cross-connect OAM-state: OAM-Up OAM-Loopback-Tx-Interval: 5 Rx cells: 0, Tx cells: 0 Rx connection-traffic-table-index: 100 Rx service-category: VBR-NRT (Non-Realtime Variable Bit Rate) Rx pcr-clp01: 106 Rx scr-clp0 : 106 Rx mcr-clp01: none Rx cdvt: none Rx mbs: 50 Tx connection-traffic-table-index: 100 Tx service-category: VBR-NRT (Non-Realtime Variable Bit Rate) Tx pcr-clp01: 106 Tx scr-clp0 : 106 Tx mcr-clp01: none Tx cdvt: none Tx mbs: 50
Cisco 800系列IDSL不支援使用訊框中繼的PPP。
如果您希望將Cisco路由器用於IDSL應用,並且路由器運行早於12.1的Cisco IOS軟體版本,則必須配置ISDN交換機型別。如需詳細資訊,請參閱設定Cisco路由器以用於IDSL。
如果不配置ISDN交換機型別,則在IDSL線路關閉並恢復後,路由器的BRI介面可能不會恢復。若要防止此問題,請在全域組態模式下發出isdn switch-type basic-ni指令。
如果Cisco路由器運行Cisco IOS軟體版本12.1或更高版本,則不會發生此問題。