답변 Firepower eXtensible 운영 체제 (FXOS) FAQ
목차
소개
이 문서에서는 FXOS 플랫폼 관련 FAQ에 대해 설명합니다.
배경 정보
FXOS(Firepower eXtensible Operating System)는 Firepower 또는 보안 방화벽 플랫폼의 기본 운영 체제입니다. 플랫폼에 따라 FXOS는 기능 구성, 섀시 상태 모니터링, 고급 문제 해결 기능 액세스에 사용됩니다.
플랫폼 모드의 Adaptive Secure Appliance 소프트웨어가 포함된 Firepower 4100/9300 및 Firepower 2100의 FXOS는 컨피그레이션 변경을 허용하지만, 특정 기능을 제외한 다른 플랫폼에서는 읽기 전용입니다.
Q. FXOS 시스템에서 Show Tech를 생성하는 방법
버전 2.8.x부터 fprm은 더 이상 사용되지 않습니다. 따라서 FXOS 2.8.x는 섀시 및 블레이드 쇼 기술만 지원합니다.
KSEC-FPR4115-2-1(local-mgmt)# show tech-support fprm detail WARNING: show tech-support fprm detail command is deprecated. Please use show tech-support chassis 1 detail command instead.
- 섀시: 섀시, 블레이드, 어댑터, BMC(Baseboard Management Controller) 및 CIMC(Cisco Integrated Management Controller)에 대한 로그 파일을 포함합니다.
- module: 논리적 디바이스 ASA(Adaptive Security Appliance) 또는 FTD(Firepower Threat Defense)가 있는 블레이드/모듈에 대한 로그 파일을 포함합니다. 여기에는 appAgent와 같은 구성 요소에 대한 로그가 포함됩니다.
2.8.x 이전 릴리스에서는 FXOS에서 3가지 show tech 출력을 제공합니다. FPRM 번들에는 MIO(Management Input/Output), 즉 수퍼바이저 엔진과 Service Manager에 대한 로그 파일이 포함되어 있습니다
일반적으로 3개의 번들을 모두 생성합니다. show tech-support <option> detail을 사용하여 TAC 분석을 위한 3가지 로그 번들을 생성합니다.
FPR4140-A# connect local-mgmt FPR4140-A(local-mgmt)# show tech-support fprm detail FPR4140-A(local-mgmt)# show tech-support chassis 1 detail FPR4140-A(local-mgmt)# show tech-support module 1 detail
- detail 옵션을 지정하지 않으면 화면에 출력이 표시됩니다
- detail 옵션은 tar 파일을 생성합니다
생성된 파일 이름을 확인하려면 다음을 수행합니다.
FPR4140-A(local-mgmt)# dir techsupport/ 1 15595520 Apr 09 17:29:10 2017 20170409172722_FPR4140_FPRM.tar 1 962560 Apr 09 17:32:20 2017 20170409172916_FPR4140_BC1_all.tar 1 7014400 Apr 09 18:06:25 2017 Firepower-Module1_04_09_2017_18_05_59.tar
CLI에서 번들을 내보내려면
FPR4140-A(local-mgmt)# copy workspace:///techsupport/20170409172722_FPR4140_FPRM.tar ftp|tftp|scp|sftp://username@192.168.0.1/
참고: FXOS show tech 출력 외에도 ASA 및/또는 FTD와 같은 논리적 디바이스에는 별도의 show tech 기능이 있습니다. MI(Multi-Instance)의 경우 각 인스턴스에는 별도의 show-tech 번들도 있습니다. 마지막으로 FCM에서는 MI show-techs가 지원되지 않습니다
FXOS 2.6부터 FXOS 기술 지원 생성 및 다운로드는 Tools(툴) > Troubleshooting Logs(문제 해결 로그) 아래의 FCM(Firepower 섀시 관리자) UI에서 제공됩니다
FP9300의 경우:
FP41xx의 경우:
Q. 섀시 관리 IP 주소, 넷마스크 및 게이트웨이를 확인하고 변경하는 방법은?
관리 인터페이스 컨피그레이션을 확인하는 방법에는 몇 가지가 있습니다.
FPR4115-2-1# show fabric-interconnect
Fabric Interconnect:
ID OOB IP Addr OOB Gateway OOB Netmask OOB IPv6 Address OOB IPv6 Gateway Prefix Operability Ingress VLAN Group Entry Count (Current/Max) Switch Forwarding Path Entry Count (Current/Max)
---- --------------- --------------- --------------- ---------------- ---------------- ------ ----------- -------------------------------------------- ------------------------------------------------
A 10.62.184.19 10.62.184.1 255.255.255.0 :: :: 64 Operable 0/500 14/1021
또는
FPR4115-2-1# scope fabric-interconnect a
FPR4115-2-1 /fabric-interconnect # show
Fabric Interconnect:
ID OOB IP Addr OOB Gateway OOB Netmask OOB IPv6 Address OOB IPv6 Gateway Prefix Operability Ingress VLAN Group Entry Count (Current/Max) Switch Forwarding Path Entry Count (Current/Max)
---- --------------- --------------- --------------- ---------------- ---------------- ------ ----------- -------------------------------------------- ------------------------------------------------
A 10.62.184.19 10.62.184.1 255.255.255.0 :: :: 64 Operable 0/500 14/1021
FPR4115-2-1 /fabric-interconnect # show detail
Fabric Interconnect:
ID: A
Product Name: Cisco FPR-4115-SUP
PID: FPR-4115-SUP
VID: V01
Vendor: Cisco Systems, Inc.
Serial (SN): JAD12345NY6
HW Revision: 0
Total Memory (MB): 8074
OOB IP Addr: 10.62.184.19
OOB Gateway: 10.62.184.1
OOB Netmask: 255.255.255.0
OOB IPv6 Address: ::
OOB IPv6 Gateway: ::
Prefix: 64
Operability: Operable
Thermal Status: Ok
Ingress VLAN Group Entry Count (Current/Max): 0/500
Switch Forwarding Path Entry Count (Current/Max): 14/1021
Current Task 1:
Current Task 2:
Current Task 3:
IP 설정을 변경하려면
FPR4115-2-1# scope fabric-interconnect a FPR4115-2-1 /fabric-interconnect # set out-of-band gw Gw ip Ip netmask Netmask KSEC-FPR4115-2-1 /fabric-interconnect # set out-of-band ip 10.62.184.19 netmask 255.255.255.0 gw 10.62.184.1 KSEC-FPR4115-2-1 /fabric-interconnect* # commit-buffer
커밋 정보:
FPR4115-2-1 /fabric-interconnect # commit-buffer verify-only ! verify the change for error FPR4115-2-1 /fabric-interconnect # commit-buffer ! commit the change FPR4115-2-1 /fabric-interconnect # discard-buffer ! cancel the change
자세한 내용은 다음을 참조하십시오.
Cisco Firepower 4100/9300 FXOS 명령 참조
Q. FXOS Ping 테스트를 실행하는 방법
local-mgmt CLI 범위로 이동하고 ping 명령을 사용합니다.
FPR4115-2-1# connect local-mgmt FPR4115-2-1(local-mgmt)# ping 10.62.184.1 PING 10.62.184.1 (10.62.184.1) from 10.62.184.19 eth0: 56(84) bytes of data. 64 bytes from 10.62.184.1: icmp_seq=1 ttl=255 time=0.602 ms 64 bytes from 10.62.184.1: icmp_seq=2 ttl=255 time=0.591 ms 64 bytes from 10.62.184.1: icmp_seq=3 ttl=255 time=0.545 ms 64 bytes from 10.62.184.1: icmp_seq=4 ttl=255 time=0.552 ms
Q. OOB(Out of Band) 관리 인터페이스의 Mac 주소를 확인하는 방법은 무엇입니까?
local-mgmt CLI 범위로 이동하고 다음 명령을 사용합니다.
FPR4115-2-1# connect local-mgmt
FPR4115-2-1(local-mgmt)# show mgmt-ip-debug | begin eth0
eth0 Link encap:Ethernet HWaddr 78:bc:1a:e7:a4:11
inet addr:10.62.184.19 Bcast:10.62.184.255 Mask:255.255.255.0
inet6 addr: fe80::7abc:1aff:fee7:a411/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3420589 errors:0 dropped:0 overruns:0 frame:0
TX packets:2551231 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:419362704 (399.9 MiB) TX bytes:1530147643 (1.4 GiB)
Q. OOB(Out of Band) 관리 인터페이스가 작동 중인지 확인하려면 어떻게 해야 합니까?
scope fabric-interconnect a(패브릭 인터커넥트 a) > show(쇼)에서 Operable(작동 가능) 외에 다음 명령을 사용할 수 있습니다.
FPR4115-2-1# connect local-mgmt
FPR4115-2-1(local-mgmt)# show mgmt-port
eth0 Link encap:Ethernet HWaddr 78:bc:1a:e7:a4:11
inet addr:10.62.184.19 Bcast:10.62.184.255 Mask:255.255.255.0
inet6 addr: fe80::7abc:1aff:fee7:a411/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3422158 errors:0 dropped:0 overruns:0 frame:0
TX packets:2552019 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:419611452 (400.1 MiB) TX bytes:1530247862 (1.4 GiB)
또는 이 명령을 사용할 수 있습니다. Scope(범위) 부분에는 Link UP(링크 업)이 표시됩니다. UP가 다음 줄에 표시됩니다.
FPR4115-2-1# connect local-mgmt
FPR4115-2-1(local-mgmt)# show mgmt-ip-debug | begin eth0
eth0 Link encap:Ethernet HWaddr 78:bc:1a:e7:a4:11
inet addr:10.62.184.19 Bcast:10.62.184.255 Mask:255.255.255.0
inet6 addr: fe80::7abc:1aff:fee7:a411/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3420589 errors:0 dropped:0 overruns:0 frame:0
TX packets:2551231 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:419362704 (399.9 MiB) TX bytes:1530147643 (1.4 GiB)
참고: UP 상태는 인터페이스의 관리자 상태입니다. 물리적 케이블 또는 SFP 모듈의 플러그를 뽑아도 상태는 UP로 유지됩니다. 또 다른 중요한 점은 RUNNING 상태이며, 이는 링크가 작동 중임을 의미합니다(라인 프로토콜이 작동 중).
인터페이스의 논리적 상태를 종료하려면
FPR4100-3-A(local-mgmt)# mgmt-port shut
FPR4100-3-A(local-mgmt)# show mgmt-ip-debug ifconfig | b eth0
eth0 Link encap:Ethernet HWaddr 58:97:BD:B9:76:EB
inet addr:10.62.148.88 Bcast:10.62.148.127 Mask:255.255.255.128
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:3685870 errors:0 dropped:0 overruns:0 frame:0
TX packets:7068372 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:295216623 (281.5 MiB) TX bytes:1049391193 (1000.7 MiB)
다시 언급하려면
FPR4100-3-A(local-mgmt)# mgmt-port no-shut
FPR4100-3-A(local-mgmt)# show mgmt-ip-debug ifconfig | b eth0
eth0 Link encap:Ethernet HWaddr 58:97:BD:B9:76:EB
inet addr:10.62.148.88 Bcast:10.62.148.127 Mask:255.255.255.128
inet6 addr: fe80::5a97:bdff:feb9:76eb/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3685885 errors:0 dropped:0 overruns:0 frame:0
TX packets:7068374 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:295218130 (281.5 MiB) TX bytes:1049391353 (1000.7 MiB)
참고: fxos 모드 아래에 각각 mgmt0 인터페이스가 down 및 Admin down으로 표시되는 show interface brief 및 show interface mgmt 0이 있습니다. 작동이 중지된 경우 이를 참조로 사용하지 마십시오.
FPR-4110-A# connect fxos FPR-4110-A(fxos)# show interface brief | include mgmt0 mgmt0 -- down 172.16.171.83 -- 1500
FPR-4110-A(fxos)# show interface mgmt 0 mgmt0 is down (Administratively down) Hardware: GigabitEthernet, address: 5897.bdb9.212d (bia 5897.bdb9.212d) Internet Address is 172.16.171.83/24 MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA auto-duplex, auto-speed EtherType is 0x0000 1 minute input rate 3080 bits/sec 2 packets/sec 1 minute output rate 0 bits/sec 0 packets/sec Rx 977 unicast packets 12571 multicast packets 5229 broadcast packets 18777 input packets 2333662 bytes Tx 0 unicast packets 0 multicast packets 0 broadcast packets 0 output packets 0 bytes
fxos 모드에서 show run interface mgmt0을 수행하는 경우 해당 인터페이스 아래에 shutdown force가 적용됩니다. 다시 한 번, 작동 중지되었음을 나타내는 참조로 사용하지 마십시오.
FPR4115-2-1(fxos)# show run interface mgmt0 !Command: show running-config interface mgmt0 !Time: Tue May 5 14:19:42 2020 version 5.0(3)N2(4.81) interface mgmt0 shutdown force ip address 10.62.184.19/24
Q. FXOS 라우팅 테이블을 확인하는 방법은 무엇입니까?
OOB(Out of Band) 관리는 기본 게이트웨이 집합에만 종속됩니다. 따라서 선택한 기본 게이트웨이가 시스템에 액세스해야 하는 클라이언트에 대한 연결을 허용하는지 확인합니다. connect fxos에 show ip route vrf all 명령이 있지만, 대역 외 관리에는 사용되지 않습니다.
Q. FXOS ARP 테이블을 확인하는 방법은 무엇입니까?
ARP 테이블은 FXOS CLI에서 표시되지 않습니다. fxos 모드(ethanalyzer)에서 패킷 캡처를 사용하여 ARP를 캡처하거나 관리자로부터 트래픽을 확인할 수도 있습니다.
ARP 패킷을 캡처하는 예입니다. capture-filter를 원하는 것으로 변경할 수 있습니다. 이 필터는 tcpdump 필터와 유사합니다.
fp9300-A# connect fxos
fp9300-A(fxos)# ethanalyzer local interface mgmt capture-filter arp
Capturing on eth0
2016-10-14 18:04:57.551221 00:50:56:85:be:44 -> ff:ff:ff:ff:ff:ff ARP Who has 172.16.171.240? Tell 172.16.171.101
2016-10-14 18:04:57.935562 00:12:80:85:a5:49 -> ff:ff:ff:ff:ff:ff ARP Who has 172.16.171.112? Tell 172.16.171.1
2016-10-14 18:04:58.167029 00:50:56:85:78:4e -> ff:ff:ff:ff:ff:ff ARP Who has 172.16.171.205? Tell 172.16.171.100
2016-10-14 18:04:59.156000 00:50:56:9f:b1:43 -> ff:ff:ff:ff:ff:ff ARP Who has 172.16.171.1? Tell 172.16.171.151
2016-10-14 18:04:59.165701 00:50:56:9f:b1:43 -> ff:ff:ff:ff:ff:ff ARP Who has 172.16.171.1? Tell 172.16.171.151
2016-10-14 18:04:59.166925 00:50:56:85:78:4e -> ff:ff:ff:ff:ff:ff ARP Who has 172.16.171.205? Tell 172.16.171.100
2016-10-14 18:04:59.268168 00:50:56:9f:b1:43 -> ff:ff:ff:ff:ff:ff ARP Who has 172.16.171.151? Tell 0.0.0.0
2016-10-14 18:05:00.150217 00:50:56:85:78:4e -> ff:ff:ff:ff:ff:ff ARP Who has 172.16.171.204? Tell 172.16.171.100
2016-10-14 18:05:00.268369 00:50:56:9f:b1:43 -> ff:ff:ff:ff:ff:ff ARP Who has 172.16.171.151? Tell 0.0.0.0
2016-10-14 18:05:01.150243 00:50:56:85:78:4e -> ff:ff:ff:ff:ff:ff ARP Who has 172.16.171.204? Tell 172.16.171.100
10 packets captured
Program exited with status 0.
fp9300-A(fxos)#
또한 캡처를 파일에 저장한 다음 원격 서버로 내보낼 수 있습니다.
FPR4140-A# connect fxos FPR4140-A(fxos)# ethanalyzer local interface mgmt capture-filter arp limit-captured-frames 0 write workspace:///ARP.pcap FPR4140-A# connect local-mgmt FPR4140-A(local-mgmt)# dir 1 23075 Jan 12 13:13:18 2020 ARP.pcap FPR4140-A(local-mgmt)# copy workspace:///ARP.pcap ftp://anonymous@10.48.40.70/ARP.pcap
Q. FXOS 결함 이벤트를 확인하는 방법은?
show fault 명령을 사용합니다.
FPR4115-2-1# show fault Severity Code Last Transition Time ID Description --------- -------- ------------------------ -------- ----------- Major F0909 2020-04-26T21:19:37.520 554924 default Keyring's certificate is invalid, reason: expired. Major F1769 2012-01-19T00:30:02.733 323268 The password encryption key has not been set. Minor F1437 2012-01-19T00:30:02.732 32358 Config backup may be outdated
심각도를 기준으로 결함을 필터링할 수도 있습니다.
FPR4115-2-1# show fault ? 0-18446744073709551615 ID <CR> > Redirect it to a file >> Redirect it to a file in append mode cause Cause detail Detail severity Severity suppressed Fault Suppressed | Pipe command output to filter FPR4115-2-1# show fault severity major Severity Code Last Transition Time ID Description --------- -------- ------------------------ -------- ----------- Major F0909 2020-04-26T21:19:37.520 554924 default Keyring's certificate is invalid, reason: expired. Major F1769 2012-01-19T00:30:02.733 323268 The password encryption key has not been set.
FXOS UI Overview(FXOS UI 개요) > FAULTS dashboard(FAULTS 대시보드)에서도 동일한 fault가 표시됩니다.
Q. 시스템의 호스트 이름을 변경하는 방법?
시스템 범위 아래에서 set name 명령을 사용합니다.
KSEC-FPR4115-2-1# scope system KSEC-FPR4115-2-1 /system # set name new-name Warning: System name modification changes FC zone name and redeploys them non-disruptively KSEC-FPR4115-2-1 /system* # commit-buffer KSEC-FPR4115-2-1 /system # exit new-name#
Q. show server status Output 아래의 "Compute Mismatch"란 무엇입니까?
새로 설치된 보안 모듈을 사용하려면 먼저 승인하고 다시 초기화해야 합니다. 이는 RMA를 통해 유닛을 교체하는 경우에도 마찬가지입니다.
FPR9300# show server status
Server Slot Status Overall Status Discovery
------- --------------------------------- --------------------- ---------
1/1 Mismatch Compute Mismatch Complete
1/2 Equipped Ok Complete
1/3 Empty
FPR9300#
컴퓨팅 불일치로 인해 다음과 같은 결함 이벤트가 발생할 수 있습니다.
Service profile ssp-sprof-1 configuration failed due to compute-unavailable,insufficient-resources
show service-profile status(서비스 프로파일 상태 표시)에는 모듈이 없는 것처럼 Unassociated(연결되지 않음)가 표시됩니다.
CLI에서 확인하는 단계:
scope chassis 1
acknowledge slot <slot#>
commit-buffer
또는 Chassis Manager UI를 사용하여 모듈을 승인합니다.
Q. show slot Output에서 "Token Mismatch"는 어떤 의미입니까?
이는 확인 응답을 받은 후 보안 모듈이 아직 다시 초기화되지 않았음을 나타냅니다.
FPR9300# scope ssa FPR9300 /ssa # show slot Slot: Slot ID Log Level Admin State Operational State ---------- --------- ------------ ----------------- 1 Info Ok Token Mismatch 2 Info Ok Online 3 Info Ok Not Available FPR9300 /ssa #
CLI를 통한 재초기화 단계:
scope ssa scope slot <#> reinitialize commit-buffer
firepower 41xx에서 이는 SSD가 없거나 결함이 있음을 의미할 수도 있습니다. 범위 서버 1/1의 show inventory storage를 통해 SSD가 여전히 존재하는지 확인합니다.
FPR4140-A# scope ssa
FPR4140-A /ssa # show slot 1
Slot:
Slot ID Log Level Admin State Oper State
---------- --------- ------------ ----------
1 Info Ok Token Mismatch
FPR4140-A /ssa # show fault severity critical
Severity Code Last Transition Time ID Description
--------- -------- ------------------------ -------- -----------
Critical F1548 2018-03-11T01:22:59.916 38768 Blade swap detected on slot 1
FPR4140-A /ssa # scope server 1/1
FPR4140-A /chassis/server # show inventory storage
Server 1/1:
Name:
User Label:
Equipped PID: FPR4K-SM-36
Equipped VID: V01
Equipped Serial (SN): FLM12345KL6
Slot Status: Equipped
Acknowledged Product Name: Cisco Firepower 4100 Series Extreme Performance Security Engine
Acknowledged PID: FPR4K-SM-36
Acknowledged VID: V00
Acknowledged Serial (SN): FLM12345KL6
Acknowledged Memory (MB): 262144
Acknowledged Effective Memory (MB): 262144
Acknowledged Cores: 36
Acknowledged Adapters: 2
Motherboard:
Product Name: Cisco Firepower 4100 Series Extreme Performance Security Engine
PID: FPR4K-SM-36
VID: V01
Vendor: Cisco Systems Inc
Serial (SN): FLM12345KL6
HW Revision: 0
RAID Controller 1:
Type: SATA
Vendor: Cisco Systems Inc
Model: CHORLEYWOOD
Serial: FLM12345KL6
HW Revision:
PCI Addr: 00:31.2
Raid Support:
OOB Interface Supported: No
Rebuild Rate: N/A
Controller Status: Unknown
Local Disk 1:
Vendor:
Model:
Serial:
HW Rev: 0
Operability: N/A
Presence: Missing
Size (MB): Unknown
Drive State: Unknown
Power State: Unknown
Link Speed: Unknown
Device Type: Unspecified
Local Disk Config Definition:
Mode: No RAID
Description:
Protect Configuration: No
Q. CLI를 통해 표준 시간대, NTP 및 DNS를 설정하려면 어떻게 해야 합니까?
이는 FXOS 플랫폼 설정에서 구성합니다. 이 문서의 지침을 적용합니다. FXOS 플랫폼 설정.
섀시 시간 설정을 확인하려면
KSEC-FPR4115-2-1# show clock
Tue May 5 21:30:55 CEST 2020
KSEC-FPR4115-2-1# show ntp
NTP Overall Time-Sync Status: Time Synchronized
모듈 부트 CLI에서 모듈/블레이드 시간을 확인하려면 다음 3가지 명령을 사용합니다.
Firepower-module1>show ntp peerstatus
remote local st poll reach delay offset disp
=======================================================================
*203.0.113.126 203.0.113.1 2 64 377 0.00006 0.000018 0.02789
remote 203.0.113.126, local 203.0.113.1
hmode client, pmode mode#255, stratum 2, precision -20
leap 00, refid [192.0.2.1], rootdistance 0.19519, rootdispersion 0.17641
ppoll 6, hpoll 6, keyid 0, version 4, association 43834
reach 377, unreach 0, flash 0x0000, boffset 0.00006, ttl/mode 0
timer 0s, flags system_peer, config, bclient, prefer, burst
reference time: dbef8823.8066c43a Mon, Dec 5 2016 8:30:59.501
originate timestamp: 00000000.00000000 Mon, Jan 1 1900 2:00:00.000
receive timestamp: dbefb27d.f914589d Mon, Dec 5 2016 11:31:41.972
transmit timestamp: dbefb27d.f914589d Mon, Dec 5 2016 11:31:41.972
filter delay: 0.00008 0.00006 0.00008 0.00009
0.00008 0.00008 0.00008 0.00009
filter offset: 0.000028 0.000018 0.000034 0.000036
0.000033 0.000036 0.000034 0.000041
filter order: 1 2 6 0
4 5 3 7
offset 0.000018, delay 0.00006, error bound 0.02789, filter error 0.00412
Firepower-module1>show ntp association
remote refid st t when poll reach delay offset jitter
==============================================================================
*203.0.113.126 192.0.2.1 2 u 37 64 377 0.062 0.018 0.017
ind assid status conf reach auth condition last_event cnt
===========================================================
1 43834 961d yes yes none sys.peer 1
associd=43834 status=961d conf, reach, sel_sys.peer, 1 event, popcorn,
srcadr=203.0.113.126, srcport=123, dstadr=203.0.113.1, dstport=123,
leap=00, stratum=2, precision=-20, rootdelay=195.190, rootdisp=176.407,
refid=192.0.2.1,
reftime=dbef8823.8066c43a Mon, Dec 5 2016 8:30:59.501,
rec=dbefb27d.f91541fc Mon, Dec 5 2016 11:31:41.972, reach=377,
unreach=0, hmode=3, pmode=4, hpoll=6, ppoll=6, headway=22, flash=00 ok,
keyid=0, offset=0.018, delay=0.062, dispersion=0.778, jitter=0.017,
xleave=0.011,
filtdelay= 0.08 0.06 0.08 0.10 0.08 0.09 0.08 0.10,
filtoffset= 0.03 0.02 0.03 0.04 0.03 0.04 0.03 0.04,
filtdisp= 0.00 0.03 1.04 1.07 2.06 2.09 3.09 3.12
Firepower-module1>show ntp sysinfo
associd=0 status=0618 leap_none, sync_ntp, 1 event, no_sys_peer,
version="ntpd 4.2.6p5@1.2349-o Fri Oct 7 17:08:03 UTC 2016 (2)",
processor="x86_64", system="Linux/3.10.62-ltsi-WR6.0.0.27_standard",
leap=00, stratum=3, precision=-23, rootdelay=195.271, rootdisp=276.641,
refid=203.0.113.126,
reftime=dbefb238.f914779b Mon, Dec 5 2016 11:30:32.972,
clock=dbefb2a7.575931d7 Mon, Dec 5 2016 11:32:23.341, peer=43834, tc=6,
mintc=3, offset=0.035, frequency=25.476, sys_jitter=0.003,
clk_jitter=0.015, clk_wander=0.011
system peer: 203.0.113.126
system peer mode: client
leap indicator: 00
stratum: 3
precision: -23
root distance: 0.19527 s
root dispersion: 0.27663 s
reference ID: [203.0.113.126]
reference time: dbefb238.f914779b Mon, Dec 5 2016 11:30:32.972
system flags: auth monitor ntp kernel stats
jitter: 0.000000 s
stability: 0.000 ppm
broadcastdelay: 0.000000 s
authdelay: 0.000000 s
time since restart: 1630112
time since reset: 1630112
packets received: 157339
packets processed: 48340
current version: 48346
previous version: 0
declined: 0
access denied: 0
bad length or format: 0
bad authentication: 0
rate exceeded: 0
Firepower-module1>
NTP 확인 및 문제 해결에 대한 자세한 내용은 이 문서를 확인하십시오. Firepower FXOS 어플라이언스에서 NTP(Network Time Protocol) 설정 구성, 확인 및 문제 해결
Q. Smart Licensing 및 HTTP 프록시를 설정하는 방법은?
ASA 논리적 디바이스의 경우 FXOS 섀시에서 스마트 라이센싱이 필요합니다. 자세한 내용은 이 문서를 참조하십시오. ASA용 라이센스 관리
다음은 라이센스 상태의 샘플 출력입니다.
FPR4115-2-1# scope license FPR4115-2-1 /license # show license all Smart Licensing Status ====================== Smart Licensing is ENABLED Registration: Status: REGISTERED Smart Account: BU Production Test Virtual Account: TAC-BETA Export-Controlled Functionality: Not Allowed Initial Registration: SUCCEEDED on Dec 15 14:41:55 2015 PST Last Renewal Attempt: SUCCEEDED on Dec 23 09:26:05 2015 PST Next Renewal Attempt: Jun 21 07:00:21 2016 PST Registration Expires: Dec 23 06:54:19 2016 PST License Authorization: Status: AUTHORIZED on Apr 07 15:44:26 2016 PST Last Communication Attempt: SUCCEEDED on Apr 07 15:44:26 2016 PST Next Communication Attempt: May 07 15:44:25 2016 PST Communication Deadline: Jul 06 15:38:24 2016 PST License Usage ============== No licenses in use Product Information =================== UDI: PID:FPR9K-SUP,SN:JAD123456AB Agent Version ============= Smart Agent for Licensing: 1.4.1_rel/31
또는
fp9300-A# connect local-mgmt
fp9300-A(local-mgmt)# show license all
Smart Licensing Status
======================
Smart Licensing is ENABLED
Registration:
Status: REGISTERED
Smart Account: Cisco Internal
Virtual Account: Escalations
Export-Controlled Functionality: Allowed
Initial Registration: SUCCEEDED on Feb 10 18:55:08 2016 CST
Last Renewal Attempt: SUCCEEDED on Oct 09 15:07:25 2016 CST
Next Renewal Attempt: Apr 07 15:16:32 2017 CST
Registration Expires: Oct 09 15:10:31 2017 CST
License Authorization:
Status: AUTHORIZED on Sep 20 07:29:06 2016 CST
Last Communication Attempt: SUCCESS on Sep 20 07:29:06 2016 CST
Next Communication Attempt: None Communication Deadline: None
Licensing HA configuration error:
No Reservation Ha config error
License Usage
==============
No licenses in use
Product Information
===================
UDI: PID:FPR9K-SUP,SN:JAD190800VU
Agent Version
=============
Smart Agent for Licensing: 1.6.7_rel/95
Q. CLI를 통해 Syslog를 구성하는 방법은 무엇입니까?
다음 문서를 확인하십시오.
Q. firepower 어플라이언스에서 SNMP를 구성하는 방법
이 문서 확인: Firepower NGFW 어플라이언스에 SNMP 구성
Q. Chassis Manager에서 사용하는 SSL 인증서를 설치/교체하는 방법은 무엇입니까?
이 문서에서는 FXOS 섀시 관리자용 신뢰할 수 있는 인증서 설치를 도와 줍니다.
Q. FPR9300 섀시를 통한 트래픽 흐름의 문제를 해결하려면 어떻게 해야 합니까?
다음 문서를 확인하십시오.
- Firepower 데이터 경로 문제 해결 1단계: 패킷 인그레스
- Firepower 데이터 경로 문제 해결: 개요
- Firepower 방화벽 캡처를 분석하여 네트워크 문제를 효과적으로 해결
Q. 섀시 Mac 주소 테이블을 보는 방법
FP41xx 및 FP93xx 플랫폼의 경우 다음 명령을 사용합니다.
FPR4115-2-1# connect fxos FPR4115-2-1(fxos)# show l2-table Ingress MAC Vlan Class VlanGrp Status Dst Eth1/1 78bc.1ae7.a45e 101 1 0 present 1 Veth776 78bc.1ae7.a45e 101 1 0 present 1 Po1 0100.5e00.0005 1001 1 0 present 1 Po1 0100.5e00.0006 1001 1 0 present 1 Po1 78bc.1ae7.a44e 1001 1 0 present 1 Po1 ffff.ffff.ffff 1001 63 0 present 1
FPR4115-2-1(fxos)# show mac address-table Legend: * - primary entry, G - Gateway MAC, (R) - Routed MAC, O - Overlay MAC age - seconds since first seen,+ - primary entry using vPC Peer-Link VLAN MAC Address Type age Secure NTFY Ports/SWID.SSID.LID ---------+-----------------+--------+---------+------+----+------------------ * 1001 0100.5e00.0005 static 0 F F Eth1/1 * 1001 0100.5e00.0006 static 0 F F Eth1/1 * 1001 78bc.1ae7.a44e static 0 F F Eth1/1 * 1001 ffff.ffff.ffff static 0 F F Eth1/1 * 101 78bc.1ae7.a45e static 0 F F Eth1/1 * 101 78bc.1ae7.a46f static 0 F F Veth776 * 4047 0015.a501.0100 static 0 F F Veth864 * 4047 0015.a501.0101 static 0 F F Veth1015 * 4043 78bc.1ae7.b000 static 0 F F Eth1/10 * 4043 78bc.1ae7.b00c static 0 F F Eth1/9 * 1 0015.a500.001f static 0 F F Veth887 * 1 0015.a500.002f static 0 F F Veth1018 * 1 0015.a500.01bf static 0 F F Veth905 * 1 0015.a500.01ef static 0 F F Veth1019
Q. 섀시 인터페이스 MAC 주소를 보려면 어떻게 해야 합니까?
다음 명령을 사용합니다.
FPR4115-2-1# connect fxos FPR4115-2-1(fxos)# show interface mac-address -------------------------------------------------------------------------------- Interface Mac-Address Burn-in Mac-Address -------------------------------------------------------------------------------- Ethernet1/1 78bc.1ae7.a417 78bc.1ae7.a418 Ethernet1/2 78bc.1ae7.a417 78bc.1ae7.a419 Ethernet1/3 78bc.1ae7.a417 78bc.1ae7.a41a Ethernet1/4 78bc.1ae7.a417 78bc.1ae7.a41b Ethernet1/5 78bc.1ae7.a417 78bc.1ae7.a41c Ethernet1/6 78bc.1ae7.a417 78bc.1ae7.a41d Ethernet1/7 78bc.1ae7.a417 78bc.1ae7.a41e Ethernet1/8 78bc.1ae7.a417 78bc.1ae7.a41f Ethernet1/9 78bc.1ae7.a417 78bc.1ae7.a420 Ethernet1/10 78bc.1ae7.a417 78bc.1ae7.a421 Ethernet1/11 78bc.1ae7.a417 78bc.1ae7.a422 Ethernet1/12 78bc.1ae7.a417 78bc.1ae7.a423 port-channel1 78bc.1ae7.a417 78bc.1ae7.a41a port-channel48 78bc.1ae7.a417 0000.0000.0000 mgmt0 78bc.1ae7.a411 78bc.1ae7.a411 Vethernet690 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet691 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet692 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet693 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet694 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet695 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet696 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet697 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet698 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet699 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet700 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet774 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet775 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet776 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet777 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet778 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet779 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet861 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet862 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet863 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet864 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet887 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet905 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet906 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet1015 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet1018 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet1019 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet1020 78bc.1ae7.a417 78bc.1ae7.a417 Vethernet1021 78bc.1ae7.a417 78bc.1ae7.a417
Q. FXOS Supervisor(MIO)에서 비밀번호 복구를 수행하는 방법은 무엇입니까?
FP41xx 및 FP9300의 비밀번호 복구 절차는 다음 문서를 참조하십시오. Firepower 9300/4100 Series 어플라이언스의 비밀번호 복구 절차
Q. ASA 또는 FTD 논리적 디바이스에서 비밀번호 복구를 수행하는 방법은 무엇입니까?
논리적 디바이스 비밀번호를 재설정하려면 디바이스를 다시 부트스트랩해야 합니다. 부트스트랩 재해 복구 프로세스에서는 다음 항목 중 하나를 변경할 수 있습니다.
- ASA/FTD 관리 IP - IP, 넷마스크, 게이트웨이, IPv6, 접두사 길이
- ASA 비밀번호
- FTD 등록 키, 비밀번호, FMC IP, 도메인 검색, 방화벽 모드, DNS 서버, FQDN
- ASA 클러스터 IP 풀, 넷마스크, 게이트웨이, 접두사 길이, 가상 IP
참고: 부트스트랩 복구 프로세스는 논리적 디바이스 재로드가 필요하므로 MW(유지 관리 기간)에서 실행해야 합니다
예 1
FXOS UI를 사용하여 논리적 디바이스의 부트스트랩 설정을 수정할 수 있습니다. Logical Devices(논리적 디바이스) 탭, Edit a device(디바이스 수정)로 이동합니다.
비밀번호를 설정합니다.
이 메시지를 저장하면 다음 메시지가 나타납니다.
예 2
다음은 ASA enable password change/recovery의 예입니다.
FP4110-A# scope ssa
FP4110-A /ssa # show logical-device
Logical Device:
Name Description Slot ID Mode Oper State Templa te Name
---------- ----------- ---------- ---------- ------------------------ ------ -------
asa 1 Standalone Ok asa
FP4110-A /ssa # scope logical-device asa
FP4110-A /ssa/logical-device # scope mgmt-bootstrap asa
FP4110-A /ssa/logical-device/mgmt-bootstrap # show config
enter mgmt-bootstrap asa
create bootstrap-key-secret PASSWORD
! set value
exit
enter ipv4 1 default
set gateway 172.16.171.1
set ip 172.16.171.226 mask 255.255.255.0
exit
exit
FP4110-A /ssa/logical-device/mgmt-bootstrap # enter bootstrap-key-secret PASSWORD
FP4110-A /ssa/logical-device/mgmt-bootstrap/bootstrap-key-secret # set value
Value: <enter new enable password in here>
Warning: Bootstrap changes are not automatically applied to app-instances. To apply the changes, please do clear-mgmt-bootstrap, and restart each app-instance.
FP4110-A /ssa/logical-device/mgmt-bootstrap/bootstrap-key-secret* # commit-buffer
FP4110-A /ssa/logical-device/mgmt-bootstrap/bootstrap-key-secret # top
FP4110-A# scope ssa
FP4110-A /ssa # scope slot 1
FP4110-A /ssa/slot # scope app-instance asa
FP4110-A /ssa/slot/app-instance # clear-mgmt-bootstrap
Warning: Clears the application management bootstrap. Application needs to be restarted for this action to be effective.
FP4110-A /ssa/slot/app-instance* # commit-buffer
FP4110-A /ssa/slot/app-instance # restart
FP4110-A /ssa/slot/app-instance* # commit-buffer
ASA에 연결하기 전에 ASA가 온라인 상태인지 확인하고 새 enable 비밀번호를 사용합니다.
FP4110-A /ssa/slot/app-instance # show
Application Instance:
App Name Admin State Oper State Running Version Startup Version Profile Name Cluster State Cluster Role
---------- ----------- ---------------- --------------- --------------- ------------ --------------- ------------
asa Enabled Online 9.9.1.76 9.9.1.76 Not Applicable None
FP4110-A /ssa/slot/app-instance #
Q. FXOS 사용자(예: admin)의 현재 비밀번호를 변경하려면 어떻게 해야 합니까?
다음 절차를 따르십시오.
FP4110-1-A# scope security FP4110-1-A /security # show local-user User Name First Name Last name --------------- --------------- --------- admin FP4110-1-A /security # enter local-user admin FP4110-1-A /security/local-user # set password Enter a password: Confirm the password: FP4110-1-A /security/local-user* # commit-buffer FP4110-1-A /security/local-user #
Q. FXOS를 다운그레이드하려면 어떻게 해야 합니까?
FXOS 이미지 다운그레이드는 공식적으로 지원되지 않습니다. Cisco에서 지원하는 유일한 FXOS 이미지 다운그레이드 방법은 디바이스의 전체 이미지를 다시 생성하는 것입니다. 이 내용은 Firepower 4100/9300 업그레이드 경로에 설명되어 있습니다
Q. ASA 논리적 디바이스를 다운그레이드/업그레이드하려면 어떻게 해야 합니까?
Chassis Manager를 통해 ASA 버전을 다운그레이드/업그레이드하려면: 논리적 디바이스의 이미지 버전 업데이트
CLI를 통해 변경하려면 다음 컨피그레이션 가이드 섹션을 사용하십시오. 논리적 디바이스의 이미지 버전 업데이트
참고: CLI에서 commit-buffer를 실행하면 모듈이 다시 시작됩니다. 마찬가지로 섀시 관리자도 ok를 누르면 모듈이 재시작됩니다. 수동으로 다시 시작할 필요가 없습니다.
Q. CLI를 통해 FXOS 업그레이드 상태를 확인하는 방법?
모든 구성 요소가 Ready(준비) 상태가 되면 업그레이드가 완료됩니다.
FP9300# scope system
FP9300 /system # show firmware monitor
FPRM:
Package-Vers: 2.0(1.37)
Upgrade-Status: Ready
Fabric Interconnect A:
Package-Vers: 2.0(1.23)
Upgrade-Status: Upgrading
Chassis 1:
Server 1:
Package-Vers: 2.0(1.23)
Upgrade-Status: Ready
Server 2:
Package-Vers: 2.0(1.23)
Upgrade-Status: Upgrading
기타 유용한 명령
FP9300 /firmware/auto-install # show fsm status FP9300 /firmware/auto-install # show fsm status expand
Q. FXOS CLI에서 논리적 디바이스를 다시 로드하는 방법은 무엇입니까?
FCM UI를 사용하는 것이 좋습니다. 어떤 이유로든 UI에 액세스할 수 없는 경우 다음 명령을 사용합니다.
# scope chassis 1
/chassis # scope server 1/1
/chassis/server # reset ?
hard-reset-immediate Perform an immediate hard reset
hard-reset-wait Wait for the completion of any pending management oper
/chassis/server # commit-buffer
Q. FXOS 섀시 가동 시간 및 마지막 다시 로드 이유를 확인하는 방법
FXOS 가동 시간 확인은 FXOS 역추적이 있는 경우에 유용합니다. UI(FCM) 또는 CLI에서 FXOS를 볼 수 있습니다.
FPR9K-1-A# connect fxos FPR9K-1-A(fxos)# show system uptime System start time: Sun Sep 25 09:57:19 2016 System uptime: 28 days, 9 hours, 38 minutes, 14 seconds Kernel uptime: 28 days, 9 hours, 38 minutes, 41 seconds Active supervisor uptime: 28 days, 9 hours, 38 minutes, 14 seconds
또한 마지막 다시 로드 이유를 확인하려면 다음 명령을 사용합니다.
FPR9K-1-A(fxos)# show system reset-reason
----- reset reason for Supervisor-module 1 (from Supervisor in slot 1) ---
1) At 212883 usecs after Fri Oct 21 22:34:35 2016
Reason: Kernel Panic
Service:
Version: 5.0(3)N2(3.02)
2) At 106690 usecs after Thu May 26 16:07:38 2016
Reason: Reset Requested by CLI command reload
Service:
Version: 5.0(3)N2(3.02)
FPR2100 업타임의 경우 다음을 수행합니다.
1. 'show tech-support fprm detail' 번들 다운로드
2. 번들의 내용을 추출합니다.
3. tmp/inventory_manager.xml 파일을 확인합니다.
가동 시간을 초 단위로 표시하는 항목이 있습니다.
tmp/inventory_manager.xml:
<uptime>151</uptime>
Q. FXOS에서 사용 가능한 디스크 공간을 확인하는 방법은?
'workspace'라고도 함:
FPR9K-1-A# connect local-mgmt FPR9K-1-A(local-mgmt)# dir 1 29 Sep 25 09:56:22 2016 blade_debug_plugin 1 19 Sep 25 09:56:22 2016 bladelog 1 16 Aug 05 15:41:05 2015 cores 1 2841476 Apr 26 14:13:12 2016 d 2 4096 Dec 01 10:09:11 2015 debug_plugin/ 1 31 Aug 05 15:41:05 2015 diagnostics 1 2842049 Feb 23 03:26:38 2016 dp 1 18053120 Feb 23 11:10:19 2016 fpr9k-1-0-sam_logs_all.tar 1 18176000 Feb 23 11:10:43 2016 fpr9k-1-1-sam_logs_all.tar 1 19302400 Feb 23 11:11:07 2016 fpr9k-1-2-sam_logs_all.tar 1 16312320 Feb 23 11:06:53 2016 fpr9k-1-3-sam_logs_all.tar 1 2841476 Feb 22 18:47:00 2016 fxos-dplug.5.0.3.N2.3.13.67g.gSSA 2 4096 Aug 05 15:38:58 2015 lost+found/ 1 25 Dec 01 11:11:50 2015 packet-capture 1 18493440 Feb 23 10:44:51 2016 sam_logs_all.tar 2 4096 Sep 14 11:23:11 2016 techsupport/ Usage for workspace:// 4032679936 bytes total 324337664 bytes used 3503489024 bytes free
FPR9K-1-A(local-mgmt)# dir volatile:/ 1 66 Oct 27 08:17:48 2016 xmlout_5816 Usage for volatile:// 251658240 bytes total 4096 bytes used 251654144 bytes free
부트 플래시 여유 공간을 확인합니다. 이 출력에는 Workspace 크기 및 사용량도 표시됩니다.
FPR9K-1-A# scope fabric-interconnect a
FPR9K-1-A /fabric-interconnect # show storage
Storage on local flash drive of fabric interconnect:
Partition Size (MBytes) Used Percentage
---------------- ---------------- ---------------
bootflash 106490 9
opt 3870 2
spare 5767 1
usbdrive Nothing Empty
workspace 3845 9
Q. FXOS의 구성을 공장 기본값으로 재설정하려면 어떻게 해야 합니까?
다음 명령을 사용합니다.
FPR9K-1-A# connect local-mgmt FPR9K-1-A(local-mgmt)# erase configuration
참고: 시스템이 재부팅되고 관리 IP 주소를 포함하여 전체 컨피그레이션이 지워집니다. 따라서 콘솔이 연결되어 있는지 확인합니다. 시스템이 재부팅되면 설정 애플리케이션이 실행되고 관리 컨피그레이션 정보를 다시 입력할 수 있습니다.
예
FPR9K-1# connect local-mgmt
FPR9K-1(local-mgmt)# erase configuration
All configurations are erased and system must reboot. Are you sure? (yes/no): yes
Removing all the configuration. Please wait....
/bin/rm: cannot remove directory `/bootflash/sysdebug//tftpd_logs': Device or resource busy
sudo: cannot get working directory
sudo: cannot get working directory
Configurations are cleaned up. Rebooting....
...
System is coming up ... Please wait ...
System is coming up ... Please wait ...
2016 Oct 28 06:31:00 %$ VDC-1 %$ %USER-0-SYSTEM_MSG: Starting bcm_attach - bcm_usd
System is coming up ... Please wait ...
2016 Oct 28 06:31:06 %$ VDC-1 %$ %USER-0-SYSTEM_MSG: Finished bcm_attach... - bcm_usd
2016 Oct 28 06:31:07 %$ VDC-1 %$ %USER-0-SYSTEM_MSG: Enabling Filter on CPU port - bcm_usd
System is coming up ... Please wait ...
2016 Oct 28 06:31:11 switch %$ VDC-1 %$ %VDC_MGR-2-VDC_ONLINE: vdc 1 has come online
System is coming up ... Please wait ...
nohup: appending output to `nohup.out'
---- Basic System Configuration Dialog ----
This setup utility guides you through the basic configuration of
the system. Only minimal configuration including IP connectivity to
the Fabric interconnect and its clustering mode is performed through these steps.
Type Ctrl-C at any time to abort configuration and reboot system.
To back track or make modifications to already entered values,
complete input till end of section and answer no when prompted
to apply configuration.
You have chosen to setup a new Security Appliance. Continue? (y/n):
Q. FXOS CLI에서 논리적 디바이스의 부트스트랩 컨피그레이션(할당된 인터페이스, 버전 등)을 확인하는 방법은 무엇입니까?
FPR4100-3-A# scope ssa
FPR4100-3-A /ssa # show configuration
scope ssa
enter logical-device FTD4150-3 ftd 1 standalone
enter external-port-link Ethernet16_ftd Ethernet1/6 ftd
set decorator ""
set description ""
set port-name Ethernet1/6
exit
enter external-port-link Ethernet17_ftd Ethernet1/7 ftd
set decorator ""
set description ""
set port-name Ethernet1/7
exit
enter external-port-link Ethernet18_ftd Ethernet1/8 ftd
set decorator ""
set description ""
set port-name Ethernet1/8
exit
enter mgmt-bootstrap ftd
enter bootstrap-key DNS_SERVERS
set value 192.0.2.100
exit
enter bootstrap-key FIREPOWER_MANAGER_IP
set value 10.62.148.57
exit
enter bootstrap-key FIREWALL_MODE
set value routed
exit
enter bootstrap-key FQDN
set value FTD4150-3.lab.com
exit
enter bootstrap-key SEARCH_DOMAINS
set value lab.com
exit
enter bootstrap-key-secret PASSWORD
! set value
exit
enter bootstrap-key-secret REGISTRATION_KEY
! set value
exit
enter ipv4 1 firepower
set gateway 10.62.148.1
set ip 10.62.148.89 mask 255.255.255.128
exit
exit
set description ""
set res-profile-name ""
exit
scope slot 1
enter app-instance ftd
enable
set startup-version 6.0.1.1213
exit
set log-level info
exit
scope app asa 9.12.4.12
set-default
exit
scope app ftd 6.0.1.1213
accept-license-agreement
set-default
exit
exit
이 값은 다음과 같습니다.
모든 FXOS 컨피그레이션을 보려면 'all' 키워드를 추가합니다(출력은 여러 페이지 길이임).
FPR4100-3-A /ssa # show configuration all
Q. FXOS 인터페이스의 상태(포트 유형, 상태)를 확인하려면 어떻게 해야 합니까?
FPR4100-3-A# scope eth-uplink
FPR4100-3-A /eth-uplink # scope fabric a
FPR4100-3-A /eth-uplink/fabric # show interface Interface: Port Name Port Type Admin State Oper State State Reason --------------- ------------------ ----------- ---------------- ------------ Ethernet1/1 Data Disabled Admin Down Administratively down Ethernet1/2 Data Disabled Admin Down Administratively down Ethernet1/3 Data Disabled Admin Down Administratively down Ethernet1/4 Data Disabled Sfp Not Present Unknown Ethernet1/5 Data Disabled Admin Down Administratively down Ethernet1/6 Data Enabled Up Ethernet1/7 Mgmt Enabled Up Ethernet1/8 Data Enabled Up FPR4100-3-A /eth-uplink/fabric #
이 값은 다음과 같습니다.
Q. 섀시의 CPU 및 메모리 사용률을 확인하는 방법은 무엇입니까?
FPR9K-2-A# connect fxos FPR9K-2-A(fxos)# show system resources Load average: 1 minute: 1.60 5 minutes: 1.30 15 minutes: 1.15 Processes : 967 total, 1 running CPU states : 1.8% user, 1.1% kernel, 97.1% idle Memory usage: 16326336K total, 4359740K used, 11966596K free
참고: 동일한 모델에 속한 두 개의 디바이스에서도 출력에 표시되는 합계가 다를 수 있습니다. 특히, 합계는 자유 명령 출력에서 가져오며, 이는 다시 /proc/meminfo에서 가져옵니다.
메모리를 확인하려면
FPR4100-8-A /fabric-interconnect # show detail
Fabric Interconnect:
ID: A
Product Name: Cisco FPR-4140-SUP
PID: FPR-4140-SUP
VID: V02
Vendor: Cisco Systems, Inc.
Serial (SN): FLM12345KL6
HW Revision: 0
Total Memory (MB): 8074
OOB IP Addr: 10.62.148.196
OOB Gateway: 10.62.148.129
OOB Netmask: 255.255.255.128
OOB IPv6 Address: ::
OOB IPv6 Gateway: ::
Prefix: 64
Operability: Operable
Thermal Status: Ok
Current Task 1:
Current Task 2:
Current Task 3:
프로세스당 메모리 사용률 확인(RES = 물리적 메모리)을 확인하려면 다음을 수행합니다.
FPR4100-2-A-A# connect local-mgmt FPR4100-2-A-A(local-mgmt)# show processes Cpu(s): 8.0%us, 4.2%sy, 3.9%ni, 83.8%id, 0.0%wa, 0.0%hi, 0.1%si, 0.0%st Mem: 8267648k total, 3866552k used, 4401096k free, 288k buffers Swap: 0k total, 0k used, 0k free, 1870528k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 5024 root -2 0 354m 114m 34m R 43 1.4 7976:51 /isan/bin/bcm_usd 1096 root 20 0 10352 3992 3332 S 0 0.0 0:00.28 sshd: admin@pts/1 1140 root 20 0 117m 78m 53m S 0 1.0 0:00.42 /isan/bin/ucssh --ucs-mgmt -p admin 1856 root 20 0 2404 632 512 S 0 0.0 2:29.32 /nuova/bin/cmcmon -f /etc/cmcmon.conf 1859 root 20 0 23804 1932 1532 S 0 0.0 1427:47 dmserver -F 1860 root 20 0 2244 472 404 S 0 0.0 0:00.01 /sbin/hotplug2 --persistent --set-rules-file /etc/automount.rules --set-worker /lib/worker_single.so 1861 root 20 0 57116 10m 6552 S 0 0.1 7:28.76 /isan/sbin/sysmgr -V 1864 root 20 0 14044 4136 1072 S 0 0.1 1:06.19 rsyslogd -c3 -i/var/run/rsyslogd.pid 4909 root 20 0 3568 1100 876 S 0 0.0 0:00.48 /isan/sbin/xinetd -syslog local7 -loop 250 -stayalive -reuse -dontfork 4911 root 20 0 58232 12m 6152 S 0 0.2 18:39.24 /isan/sbin/syslogd -d -n -m 0 -r 4912 root 20 0 20076 3532 2368 S 0 0.0 0:00.02 /isan/bin/sdwrapd 4913 root 21 1 2756 300 192 S 0 0.0 0:00.04 /usr/sbin/in.tftpd -l -c -s /bootflash 4914 root 20 0 58312 17m 8724 S 0 0.2 13:45.34 /isan/bin/pfm 4937 root 20 0 2208 332 272 S 0 0.0 0:00.01 /sbin/klogd -2 -x -c 1 4939 root 20 0 26692 4656 3620 S 0 0.1 0:24.01 /isan/bin/vshd
...
팁:
1. show process memory 출력을 수집합니다.
2. Linux 시스템의 파일에 출력을 붙여넣습니다(cat > top.log).
3. RES 열을 기준으로 파일을 정렬합니다.
GB, MB 등을 보여줍니다
mzafeiro@MZAFEIRO-JA2YS:$ cat top.log | sort -V -k 6 1954 root 20 0 1645m 1.6g 1372 S 0.0 20.7 793:32.99 dmserver 7556 root 20 0 207m 9.8m 6184 S 0.0 0.1 73:52.25 udld 5563 root 20 0 333m 9.8m 7032 S 0.0 0.1 5:08.65 cdpd 5523 root 20 0 327m 103m 28m S 0.0 1.3 0:12.38 afm 24040 daemon 23 3 592m 115m 33m S 0.0 1.5 74:56.57 httpd 5329 root -2 0 384m 132m 29m S 9.4 1.7 27130:09 bcm_usd 5317 root 20 0 401m 150m 35m S 0.0 1.9 33:19.05 fwm 5625 root 24 4 450m 179m 35m S 0.0 2.3 275:38.25 svc_sam_statsAG 5614 root 23 3 495m 247m 54m S 0.0 3.2 355:59.95 svc_sam_dme 21688 root 20 0 2672 1080 880 S 0.0 0.0 3:15.29 ntpd 8819 root 35 15 2408 1084 748 R 5.6 0.0 0:00.06 top
Q. 섀시 인터페이스 트랜시버 유형을 확인하는 방법은?
firepower 4100/9300에서 다음 명령을 사용합니다.
FPR9K-2-A# connect fxos
FPR9K-2-A(fxos)# show interface e1/3 transceiver details
Ethernet1/3
transceiver is present
type is 1000base-T
name is CISCO-METHODE
part number is SP7041-R
revision is
serial number is FLM12345KL6
nominal bitrate is 1300 MBit/sec
Link length supported for copper is 100 m
cisco id is --
cisco extended id number is 4
DOM is not supported
FPR9K-2-A(fxos)#
파이버의 경우 출력은 다음과 같습니다.
FPR4100-1-A(fxos)# show interface e1/1 transceiver details
Ethernet1/1
transceiver is present
type is 10Gbase-SR
name is CISCO-JDSU
part number is PLRXPL-SC-S43-CS
revision is 1
serial number is FLM12345KL6
nominal bitrate is 10300 MBit/sec
Link length supported for 50/125um OM2 fiber is 82 m
Link length supported for 62.5/125um fiber is 26 m
Link length supported for 50/125um OM3 fiber is 300 m
cisco id is --
cisco extended id number is 4
Calibration info not available
firepower 1000/2100에서 다음 명령을 사용합니다.
FPR2100# scope fabric-interconnect
FPR2100 /fabric-interconnect # show inventory expand detail | egrep ignore-case "Port|Xcvr"
...
Slot 1 Port 13:
Xcvr: 10 Gbase SR
Xcvr Model: PLRXPL-SC-S43-C
Xcvr Vendor: Cisco Systems, Inc.
Xcvr Serial: ABCD1234
Slot 1 Port 14:
Xcvr: 10 Gbase SR
Xcvr Model: PLRXPL-SC-S43-C
Xcvr Vendor: Cisco Systems, Inc.
Xcvr Serial: VWXY1234
Slot 1 Port 15:
Xcvr: Non Present
Xcvr Model:
Xcvr Vendor:
Xcvr Serial:
Slot 1 Port 16:
Xcvr: Non Present
Xcvr Model:
Xcvr Vendor:
Xcvr Serial:
Q. 모듈/블레이드/서버/Netmod 정보(HW 유형/PID/SN/메모리/코어 등)를 확인하는 방법은?
이 명령은 섀시 및 모듈(netmod)의 제품 ID(PID) 및 일련 번호(SN)를 표시합니다
FP4110-7-A# connect fxos
FP4110-7-A(fxos)# show inventory NAME: "Chassis", DESCR: "Firepower 41xx Security Appliance" PID: FPR-4110-SUP , VID: V02 , SN: FLM12345KL6 <--- Chassis SN NAME: "Module 1", DESCR: "Firepower 41xx Supervisor" PID: FPR-4110-SUP , VID: V02 , SN: FLM12345KL6 <--- Embedded module on FPR4100 NAME: "Module 3", DESCR: "Firepower 6x10G FTW SFP+ SR NM" PID: FPR-NM-6X10SR-F , VID: V00 , SN: FLM12345KL6 <--- FTW Netmode SN
FPR4110에는 네트워크 모듈용 슬롯 2개(2 및 3)가 있으며, 이 예의 디바이스에는 슬롯 3에 FTW netmod가 설치되어 있습니다.
FPR9K-1-A# scope chassis 1
FPR9K-1-A /chassis # show inventory server
Chassis 1:
Servers:
Server 1/1:
Equipped Product Name: Cisco Firepower 9000 Series High Performance Security Module
Equipped PID: FPR9K-SM-36
Equipped VID: V01
Equipped Serial (SN): FLM12345KL6
Slot Status: Equipped
Acknowledged Product Name: Cisco Firepower 9000 Series High Performance Security Module
Acknowledged PID: FPR9K-SM-36
Acknowledged VID: V01
Acknowledged Serial (SN): FLM12345KL6
Acknowledged Memory (MB): 262144
Acknowledged Effective Memory (MB): 262144
Acknowledged Cores: 36
Acknowledged Adapters: 2
Server 1/2:
Equipped Product Name: Cisco Firepower 9000 Series High Performance Security Module
Equipped PID: FPR9K-SM-36
Equipped VID: V01
Equipped Serial (SN): FLM12345KL6
Slot Status: Equipped
Acknowledged Product Name: Cisco Firepower 9000 Series High Performance Security Module
Acknowledged PID: FPR9K-SM-36
Acknowledged VID: V01
Acknowledged Serial (SN): FLM12345KL6
Acknowledged Memory (MB): 262144
Acknowledged Effective Memory (MB): 262144
Acknowledged Cores: 36
Acknowledged Adapters: 2
Server 1/3:
Equipped Product Name: Cisco Firepower 9000 Series High Performance Security Module
Equipped PID: FPR9K-SM-36
Equipped VID: V01
Equipped Serial (SN): FLM12345KL6
Slot Status: Equipped
Acknowledged Product Name: Cisco Firepower 9000 Series High Performance Security Module
Acknowledged PID: FPR9K-SM-36
Acknowledged VID: V01
Acknowledged Serial (SN): FLM12345KL6
Acknowledged Memory (MB): 262144
Acknowledged Effective Memory (MB): 262144
Acknowledged Cores: 36
Acknowledged Adapters: 2
서버 1/1 = 모듈/블레이드 1
서버 1/2 = 모듈/블레이드 2
서버 1/3 = 모듈/블레이드 3
FPR41xx 모델 PID:
- FPR4K-SM-12 = FPR4110
- FPR4K-SM-24 = FPR4120
- FPR4K-SM-36 = FPR4140
- FPR4K-SM-44 = FPR4150
- FPR4K-SM-24S = FPR4115
- FPR4K-SM-32S = FPR4125
- FPR4K-SM-44S = FPR4145
범위 서버 <chassis-id/blade-id>에서 다른 정보를 얻을 수도 있습니다.
FP9300-A# scope server 1/1
FP9300-A /chassis/server # show inventory
<CR>
> Redirect it to a file
>> Redirect it to a file in append mode
adapter Adapter
bios Bios
board Board
cpu Cpu
detail Detail
expand Expand
memory Memory
mgmt Mgmt
storage Storage
| Pipe command output to filter
FP9300-A /chassis/server # show inventory storage
Server 1/1:
Name:
User Label:
Equipped PID: FPR9K-SM-36
Equipped VID: V01
Equipped Serial (SN): FLM12345PBD
Slot Status: Equipped
Acknowledged Product Name: Cisco Firepower 9000 Series High Performance Security Module
Acknowledged PID: FPR9K-SM-36
Acknowledged VID: 01
Acknowledged Serial (SN): FLM67890PBD
Acknowledged Memory (MB): 262144
Acknowledged Effective Memory (MB): 262144
Acknowledged Cores: 36
Acknowledged Adapters: 2
Motherboard:
Product Name: Cisco Firepower 9000 Series High Performance Security Module
PID: FPR9K-SM-36
VID: V01
Vendor: Cisco Systems Inc
Serial (SN): FLM12345KL6
HW Revision: 0
RAID Controller 1:
Type: SAS
Vendor: Cisco Systems Inc
Model: UCSB-MRAID12G
Serial: FLM12345KL6
HW Revision: C0
PCI Addr: 01:00.0
Raid Support: RAID0, RAID1
OOB Interface Supported: Yes
Rebuild Rate: 30
Controller Status: Optimal
Local Disk 1:
Product Name:
PID:
VID:
Vendor: TOSHIBA
Model: PX02SMF080
Vendor Description:
Serial: FLM12345KL6
HW Rev: 0
Block Size: 512
Blocks: 1560545280
Operability: Operable
Oper Qualifier Reason: N/A
Presence: Equipped
Size (MB): 761985
Drive State: Online
Power State: Active
Link Speed: 12 Gbps
Device Type: SSD
Local Disk 2:
Product Name:
PID:
VID:
Vendor: TOSHIBA
Model: PX02SMF080
Vendor Description:
Serial: FLM12345KL6
HW Rev: 0
Block Size: 512
Blocks: 1560545280
Operability: Operable
Oper Qualifier Reason: N/A
Presence: Equipped
Size (MB): 761985
Drive State: Online
Power State: Active
Link Speed: 12 Gbps
Device Type: SSD
Local Disk Config Definition:
Mode: RAID 1 Mirrored
Description:
Protect Configuration: Yes
Virtual Drive 0:
Type: RAID 1 Mirrored
Block Size: 512
Blocks: 1560545280
Operability: Operable
Presence: Equipped
Size (MB): 761985
Lifecycle: Allocated
Drive State: Optimal
Strip Size (KB): 64
Access Policy: Read Write
Read Policy: Normal
Configured Write Cache Policy: Write Through
Actual Write Cache Policy: Write Through
IO Policy: Direct
Drive Cache: No Change
Bootable: True
FP9300-A /chassis/server #
참고: FP41xx 플랫폼의 경우 RAID를 사용하지 않으므로 show inventory storage에 Controller Status(컨트롤러 상태)가 Unknown(알 수 없음)으로 표시됩니다. RAID가 아닌 주된 이유는 두 번째 SSD가 FTD 논리적 디바이스에서 MSP(Malware Storage Pack)와 같은 다른 기능에 사용되기 때문입니다.
Q. FXOS GUI 및 CLI에서 ASA 또는 FTD 이미지를 삭제하는 방법?
FCM GUI에서:
GUI에서 삭제하려면 System(시스템) > Updates(업데이트)로 이동하여 이미지를 삭제합니다.
FXOS CLI에서
FPR4100# scope ssa
FPR4100 /ssa # show app
Application:
Name Version Description Author Deploy Type CSP Type Is Default App
------ ---------- ----------- ---------- ----------- ----------- --------------
asa 9.6.1 N/A cisco Native Application Yes
ftd 6.0.1.1213 N/A cisco Native Application No
ftd 6.1.0.330 N/A cisco Native Application Yes
FPR4100 /ssa # delete app asa 9.6.1
FPR4100 /ssa* # commit
FPR4100 /ssa # show app
Application:
Name Version Description Author Deploy Type CSP Type Is Default App
---------- ---------- ----------- ---------- ----------- ----------- --------------
ftd 6.0.1.1213 N/A cisco Native Application No
ftd 6.1.0.330 N/A cisco Native Application Yes
Q. CLI에서 FXOS 버전을 확인하는 방법은 무엇입니까?
이 작업을 수행하는 몇 가지 방법이 있습니다.
방법 1
FPR4100# show fabric-interconnect firmware
Fabric Interconnect A:
Running-Kern-Vers: 5.0(3)N2(4.01.65)
Running-Sys-Vers: 5.0(3)N2(4.01.65)
Package-Vers: 2.0(1.86)
Startup-Kern-Vers: 5.0(3)N2(4.01.65)
Startup-Sys-Vers: 5.0(3)N2(4.01.65)
Act-Kern-Status: Ready
Act-Sys-Status: Ready
Bootloader-Vers:
이는 FCM GUI에서 볼 수 있는 것과 동일합니다.
2단계
FP4145-1# show version
Version: 2.6(1.192)
Startup-Vers: 2.6(1.192)
Q. FXOS에서 인터페이스 MTU를 확인하는 방법은?
firepower 4100/9300 섀시는 기본적으로 점보 프레임을 지원합니다. 다음 명령을 사용하여 인터페이스 MTU를 확인할 수 있습니다.
FPR9K-1-A# connect fxos
FPR9K-1-A(fxos)# show hardware internal bcm-usd info phy-info all +-----------------+------------------------------------------------------------+ | port phy info | +-----------------+------------------------------------------------------------+ front-port : 1 asic-port : 125 sfp installed : yes enable : ena speed : 1G autoneg : on interface : (10)XFI duplex: half linkscan : sw pause_tx : 0x0 pause_rx : 0x0 max frame : 9216 local_advert : 0x20 remote_advert : 0x420 port_40g_enable : 0 local_fault : 0x1 remote_fault : 0x0 xcvr sfp type : (1)PHY_SFP_1G_COPPER TSC4 registers: txfir(0xc252):0x0000 txdrv(0xc017):0x0000 lane(0x9003):0x1b1b Asic 56846 Registers signal_detect(1.0x81d0):0x0000 link_status(1.0x81d1):0x0000 rx_link_state(1.0x0):0x0000 pcs_rx_tx_fault(1.0x0008):0x0000 pcs_block_status_0x20(1.0x20) :0x0000 pcs_block_status_0x21(1.0x021) : 0x0000 transmitter_reg(1.0x8000):0x0000 micro_ver(1.0x81f0):0x0000
또는 fxos 명령 셸에서 MTU를 선택합니다.
KSEC-FPR4112-4# connect fxos
<output is skipped>
KSEC-FPR4112-4(fxos)# show interface ethernet 1/1
Ethernet1/1 is up
Dedicated Interface
Hardware: 1000/10000 Ethernet, address: 14a2.a02f.07c0 (bia 14a2.a02f.07c0)
Description: U: Uplink
MTU 9216 bytes, BW 1000000 Kbit, DLY 10 usec
Q. 설치된 애플리케이션을 확인하는 방법은 무엇입니까?
섀시 CLI에서 명령 범위 ssa를 사용한 다음 show slot expand detail을 사용합니다.
동일한 정보는 섀시 show tech bundle 내의 sam_techsupportinfo 파일에서 찾을 수 있습니다.
`scope ssa`
`show slot expand detail`
Slot:
Slot ID: 1
Log Level: Info
Admin State: Ok
Operational State: Online
Disk State: Ok
Clear Log Data: Available
Application Instance:
Application Name: asa
Admin State: Enabled
Operational State: Online
Running Version: 9.6.2
Startup Version: 9.6.2
Hotfixes:
Externally Upgraded: No
Cluster Oper State: Not Applicable
Current Job Type: Start
Current Job Progress: 100
Current Job State: Succeeded
Clear Log Data: Available
Error Msg:
Current Task:
App Attribute:
App Attribute Key: mgmt-ip
Value: 0.0.0.0
App Attribute Key: mgmt-url
Value: https://0.0.0.0/
Heartbeat:
Last Received Time: 2017-03-15T10:25:02.220
Heartbeat Interval: 1
Max Number of Missed heartbeats Permitted: 3
Resource:
Allocated Core NR: 46
Allocated RAM (KB): 233968896
Allocated Data Disk (KB): 20971528
Allocated Binary Disk (KB): 174964
Allocated Secondary Disk (KB): 0
Heartbeat:
Last Received Time: 2017-03-15T10:25:00.447
Heartbeat Interval: 5
Max Number of Missed heartbeats Permitted: 3
Monitor:
OS Version: 9.6(1.150)
CPU Total Load 1 min Avg: 48.110001
CPU Total Load 5 min Avg: 48.110001
CPU Total Load 15 min Avg: 48.110001
Memory Total (KB): 264377600
Memory Free (KB): 236835112
Memory Used (KB): 27542488
Memory App Total (KB): 233968896
Disk File System Count: 5
Blade Uptime: up 1 day, 6:56
Last Updated Timestamp: 2017-03-15T10:24:10.306
Disk File System:
File System: /dev/sda1
Mount Point: /mnt/boot
Disk Total (KB): 7796848
Disk Free (KB): 7694456
Disk Used (KB): 102392
File System: /dev/sda2
Mount Point: /opt/cisco/config
Disk Total (KB): 1923084
Disk Free (KB): 1734420
Disk Used (KB): 90976
File System: /dev/sda3
Mount Point: /opt/cisco/platform/logs
Disk Total (KB): 4805760
Disk Free (KB): 4412604
Disk Used (KB): 149036
File System: /dev/sda5
Mount Point: /var/data/cores
Disk Total (KB): 48061320
Disk Free (KB): 43713008
Disk Used (KB): 1906892
File System: /dev/sda6
Mount Point: /opt/cisco/csp
Disk Total (KB): 716442836
Disk Free (KB): 714947696
Disk Used (KB): 1495140
Q. FXOS CLI에서 포트 채널 구성을 확인하는 방법은 무엇입니까?
포트 채널 확인 명령
확인 1
현재 섀시에 구성된 포트 채널을 확인하려면 다음을 수행합니다.
FPR9K-1-A# connect fxos
FPR9K-1-A(fxos)# show port-channel summary Flags: D - Down P - Up in port-channel (members) I - Individual H - Hot-standby (LACP only) s - Suspended r - Module-removed S - Switched R - Routed U - Up (port-channel) M - Not in use. Min-links not met -------------------------------------------------------------------------------- Group Port- Type Protocol Member Ports Channel -------------------------------------------------------------------------------- 11 Po11(SU) Eth LACP Eth1/4(P) Eth1/5(P) 15 Po15(SD) Eth LACP Eth1/6(D) 48 Po48(SU) Eth LACP Eth1/2(P) Eth1/3(P)
확인 2
논리적 디바이스에 할당된 포트 채널을 확인하려면
FPR9K-1-A# scope ssa
FPR9K-1-A /ssa # show configuration
scope ssa
enter logical-device ftd_682021968 ftd "1,2,3" clustered
enter cluster-bootstrap
set chassis-id 1
set ipv4 gateway 0.0.0.0
set ipv4 pool 0.0.0.0 0.0.0.0
set ipv6 gateway ::
set ipv6 pool :: ::
set virtual ipv4 0.0.0.0 mask 0.0.0.0
set virtual ipv6 :: prefix-length ""
! set key
set mode spanned-etherchannel
set name 682021968
set site-id 0
exit
enter external-port-link Ethernet11_ftd Ethernet1/1 ftd
set decorator ""
set description ""
set port-name Ethernet1/1
exit
enter external-port-link PC11_ftd Port-channel11 ftd
set decorator ""
set description ""
set port-name Port-channel11
exit
enter external-port-link PC48_ftd Port-channel48 ftd
set decorator ""
set description ""
set port-name Port-channel48
exit
확인 3
포트당 포트 채널 트래픽 통계를 확인하려면
FPR9K-1-A(fxos)# show port-channel traffic interface port-channel 11
ChanId Port Rx-Ucst Tx-Ucst Rx-Mcst Tx-Mcst Rx-Bcst Tx-Bcst
------ --------- ------- ------- ------- ------- ------- -------
11 Eth1/4 62.91% 0.0% 58.90% 49.99% 100.00% 0.0%
11 Eth1/5 37.08% 0.0% 41.09% 50.00% 0.0% 0.0%
확인 4
특정 Port-Channel의 세부사항을 확인하려면
FPR9K-1-A(fxos)# show port-channel database interface port-channel 11
port-channel11
Last membership update is successful
2 ports in total, 2 ports up
First operational port is Ethernet1/4
Age of the port-channel is 0d:20h:26m:27s
Time since last bundle is 0d:18h:29m:07s
Last bundled member is Ethernet1/5
Ports: Ethernet1/4 [active ] [up] *
Ethernet1/5 [active ] [up]
확인 5
로컬 LACP 시스템 ID를 확인하려면
FPR9K-1-A(fxos)# show lacp system-identifier 32768,b0-aa-77-2f-81-bb
확인 6
LACP 상태 플래그와 함께 업스트림 디바이스의 LACP 시스템 ID를 확인하려면 다음을 수행합니다.
FPR9K-1-A(fxos)# show lacp neighbor
Flags: S - Device is sending Slow LACPDUs F - Device is sending Fast LACPDUs
A - Device is in Active mode P - Device is in Passive mode
port-channel11 neighbors
Partner's information
Partner Partner Partner
Port System ID Port Number Age Flags
Eth1/4 32768,4-62-73-d2-65-0 0x118 66828 FA
LACP Partner Partner Partner
Port Priority Oper Key Port State
32768 0xb 0x3d
Partner's information
Partner Partner Partner
Port System ID Port Number Age Flags
Eth1/5 32768,4-62-73-d2-65-0 0x119 66826 FA
LACP Partner Partner Partner
Port Priority Oper Key Port State
32768 0xb 0x3d
확인 7
포트 채널 이벤트 기록을 확인하려면
FPR9K-1-A(fxos)# show port-channel internal event-history all
Low Priority Pending queue: len(0), max len(1) [Thu Apr 6 11:07:48 2017]
High Priority Pending queue: len(0), max len(16) [Thu Apr 6 11:07:48 2017]
PCM Control Block info:
pcm_max_channels : 4096
pcm_max_channel_in_use : 48
pc count : 3
hif-pc count : 0
Max PC Cnt : 104
Load-defer timeout : 120
====================================================
PORT CHANNELS:
2LvPC PO in system : 0
port-channel11
channel : 11
bundle : 65535
ifindex : 0x1600000a
admin mode : active
oper mode : active
fop ifindex : 0x1a003000
nports : 2
active : 2
pre cfg : 0
ltl : 0x0 (0)
lif : 0x0
iod : 0x78 (120)
global id : 3
flag : 0
lock count : 0
num. of SIs: 0
ac mbrs : 0 0
lacp graceful conv disable : 0
lacp suspend indiv disable : 1
pc min-links : 1
pc max-bundle : 16
pc max active members : 32
pc is-suspend-minlinks : 0
port load defer enable : 0
lacp fast-select-hot-standby disable : 0
ethpm bundle lock count : 0
bundle res global id : 2
Members:
Ethernet1/4 [bundle_no = 0]
Ethernet1/5 [bundle_no = 0]
port-channel external lock:
Lock Info: resource [eth-port-channel 11]
type[0] p_gwrap[(nil)]
FREE @ 246108 usecs after Wed Apr 5 14:18:10 2017
type[1] p_gwrap[(nil)]
FREE @ 436471 usecs after Wed Apr 5 16:15:30 2017
type[2] p_gwrap[(nil)]
FREE @ 436367 usecs after Wed Apr 5 16:15:30 2017
0x1600000a
internal (ethpm bundle) lock:
Lock Info: resource [eth-port-channel 11]
type[0] p_gwrap[(nil)]
FREE @ 246083 usecs after Wed Apr 5 14:18:10 2017
type[1] p_gwrap[(nil)]
FREE @ 610546 usecs after Wed Apr 5 16:19:04 2017
type[2] p_gwrap[(nil)]
FREE @ 610437 usecs after Wed Apr 5 16:19:04 2017
0x1600000a
>>>>FSM: <eth-port-channel 11> has 194 logged transitions<<<<<
1) FSM:<eth-port-channel 11> Transition at 557291 usecs after Wed Apr 5 16:04:27 2017
Previous state: [PCM_PC_ST_WAIT_REL_RESRC]
Triggered event: [PCM_PC_EV_REL_RESRC_DONE]
Next state: [PCM_PC_ST_INIT]
2) FSM:<eth-port-channel 11> Transition at 49036 usecs after Wed Apr 5 16:07:18 2017
Previous state: [PCM_PC_ST_INIT]
Triggered event: [PCM_PC_EV_L2_CREATE]
Next state: [PCM_PC_ST_WAIT_CREATE]
3) FSM:<eth-port-channel 11> Transition at 49053 usecs after Wed Apr 5 16:07:18 2017
Previous state: [PCM_PC_ST_WAIT_CREATE]
Triggered event: [PCM_PC_EV_L2_CREATED]
Next state: [PCM_PC_ST_CREATED]
확인 8
Debug lacp all은 매우 큰 출력을 생성합니다.
FPR9K-1-A(fxos)# debug lacp all
2017 Jul 11 10:42:23.854160 lacp: lacp_pkt_parse_pdu(569): lacp_pkt_parse_pdu: got packet from actorport=220a partnerport= 43 2017 Jul 11 10:42:23.854177 lacp: lacp_pkt_compute_port_params(1163): Ethernet1/3(0x1a002000): pa aggregatable state=1 ac aggregatable state=1 pkt sync=1 port_stateactive=1 2017 Jul 11 10:42:23.854190 lacp: lacp_pkt_compute_port_params(1170): p_el=(8000, 2-0-0-0-0-1, 136, 8000, 220a) 2017 Jul 11 10:42:23.854198 lacp: lacp_pkt_compute_port_params(1172): p_el_pkt=(8000, 2-0-0-0-0-1, 136, 8000, 220a) 2017 Jul 11 10:42:23.854207 lacp: lacp_utils_get_obj_type_from_ifidx(390): lacp_utils_get_obj_type_from_ifidx: For if-index 1a002000 , if_type =26 2017 Jul 11 10:42:23.854218 lacp: Malloc in fu_fsm_event_new@../utils/fsmutils/fsm.c[5317]-ty[1]0x9bf719c[124] 2017 Jul 11 10:42:23.854228 lacp: lacp_utils_cr_fsm_event(572): Called from lacp_utils_create_fsm_event_with_params: Create event 0x9bf719c 2017 Jul 11 10:42:23.854237 lacp: Malloc in fu_fsm_event_pair_new@../utils/fsmutils/fsm.c[5327]-ty[2]0x9bf730c[132] 2017 Jul 11 10:42:23.854248 lacp: fu_fsm_execute_all: match_msg_id(0), log_already_open(0) 2017 Jul 11 10:42:23.854257 lacp: Malloc in fu_fsm_event_new@../utils/fsmutils/fsm.c[5317]-ty[1]0x9bf719c[124] 2017 Jul 11 10:42:23.854268 lacp: fu_fsm_execute: (Ethernet1/3) 2017 Jul 11 10:42:23.854275 lacp: current state [LACP_ST_PORT_MEMBER_COLLECTING_AND_DISTRIBUTING_ENABLED] 2017 Jul 11 10:42:23.854283 lacp: current event [LACP_EV_PARTNER_PDU_IN_SYNC_COLLECT_ENABLED_DISTRIBUTING_ENABLED] 2017 Jul 11 10:42:23.854291 lacp: next state [FSM_ST_NO_CHANGE] 2017 Jul 11 10:42:23.854304 lacp: lacp_proto_get_state(969): IF Ethernet1/3(0x1a002000): end PartnerEnd(2): state TimeOut(1): enable_flag False 2017 Jul 11 10:42:23.854314 lacp: lacp_proto_record_pdu(2266): Recording PDU for LACP pkt on IF Ethernet1/3(0x1a002000) 2017 Jul 11 10:42:23.854325 lacp: lacp_proto_set_state(900): IF Ethernet1/3(0x1a002000): Set end ActorEnd(1): state Defaulted(6) from False to False 2017 Jul 11 10:42:23.854335 lacp: lacp_proto_get_state(969): IF Ethernet1/3(0x1a002000): end PartnerEnd(2): state TimeOut(1): enable_flag False 2017 Jul 11 10:42:23.854344 lacp: lacp_proto_update_ntt(2211): updateNTT called for IF Ethernet1/3(0x1a002000) 2017 Jul 11 10:42:23.854355 lacp: lacp_proto_get_state(969): IF Ethernet1/3(0x1a002000): end ActorEnd(1): state TimeOut(1): enable_flag True 2017 Jul 11 10:42:23.854362 lacp: lacp_timer_start_w_chgd_time(681): lacp_timer_start_w_chgd_time: starting timer with time in ms = 15000 2017 Jul 11 10:42:23.854377 lacp: lacp_timer_start(637): Timer Started: Timer_Arg ([rid type IF-Rid: ifidx 0x1a002000: ch_num 0: event_id LACP_EV_RECEIVE_PARTNER_PDU_TIMED_OUT(17): timer_id 426092: type PartnerTimedOut: active True: period_in_ms 15000]) 2017 Jul 11 10:42:23.854386 lacp: lacp_timer_start(638): Timer period=15 seconds 2017 Jul 11 10:42:23.854396 lacp: Free ptr in fu_fsm_execute@../utils/fsmutils/fsm.c[1091] for addr 0x9bf719c 2017 Jul 11 10:42:23.854408 lacp: fu_fsm_execute_all: done processing event LACP_EV_PARTNER_PDU_IN_SYNC_COLLECT_ENABLED_DISTRIBUTING_ENABLED 2017 Jul 11 10:42:23.854419 lacp: fu_mts_drop ref 0x9bf7320 opc 90117 2017 Jul 11 10:42:23.854434 lacp: fu_fsm_execute_all: MTS_OPC_NET_L2_RX_DATA_HDR(msg_id 2623696) dropped 2017 Jul 11 10:42:23.854445 lacp: fu_fsm_engine_post_event_processing 2017 Jul 11 10:42:23.854453 lacp: end of while in fu_fsm_engine 2017 Jul 11 10:42:23.854461 lacp: fu_handle_process_hot_plugin_msg: Entered the function line 143 2017 Jul 11 10:42:23.854468 lacp: begin fu_fsm_engine: line[2357] 2017 Jul 11 10:42:24.361501 lacp: lacp_pkt_encode_pdu_helper(770): lacp_pkt_encode_pdu_helper: pkt_len=LACP_PDU_LEN=110 periodic_rate:1 2017 Jul 11 10:42:24.361530 lacp: lacp_pkt_encode_pdu_helper(797): lacp_pkt_encode_pdu_helper: if_idx=Ethernet1/3(0x1a002000) partner-mac=0-a6-ca-f3-c7-83 port_num=43 2017 Jul 11 10:42:24.361542 lacp: lacp_debug_wrapper_tl(1718): Executing [mcecm_api_is_pc_mcec] 2017 Jul 11 10:42:24.361551 lacp: lacp_debug_wrapper_tl(1718): input: if_index = [0x16000000] 2017 Jul 11 10:42:24.361559 lacp: lacp_debug_wrapper_tl(1718): Executing [mcecm_cache_is_pc_mcec] 2017 Jul 11 10:42:24.361568 lacp: lacp_debug_wrapper_tl(1718): output:0 2017 Jul 11 10:42:24.361589 lacp: lacp_pkt_encode_pdu_helper(842): 0x1a002000: Set short_timeout to periodic_rate:1 2017 Jul 11 10:42:24.361599 lacp: lacp_pkt_encode_pdu_helper(879): lacp_pkt_encode_pdu_helper: actor-port-state=3f agg=1 insync=1 coll=1 dis=1 active=1 short_timeout=1 2017 Jul 11 10:42:24.361612 lacp: lacp_pkt_encode_pdu_helper(906): lacp_pkt_encode_pdu_helper: if_idx=Ethernet1/3(0x1a002000) partner-port-state=3d agg=1 insync=1 coll=1 dis=1 active=1 short-timeout=0 2017 Jul 11 10:42:24.361624 lacp: lacp_pkt_encode_pdu_helper(910): lacp_pkt_encode_pdu_helper: if_idx=Ethernet1/3(0x1a002000) partner-mac=2-0-0-0-0-1 port_num=220a 2017 Jul 11 10:42:24.361636 lacp: lacp_net_tx_data(206): lacp_net_tx_data: Sending buffer with length 110 2017 Jul 11 10:42:24.361648 lacp: lacp_net_tx_data(215): 01 01 01 14 ffff 2017 Jul 11 10:42:24.361658 lacp: lacp_net_tx_data(215): ffff 2017 Jul 11 10:42:24.361668 lacp: lacp_net_tx_data(215): 00 00 00 02 14 ffff 2017 Jul 11 10:42:24.361678 lacp: lacp_net_tx_data(215): ffff 2017 Jul 11 10:42:24.361689 lacp: lacp_net_tx_data(215): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 2017 Jul 11 10:42:24.361700 lacp: lacp_net_tx_data(215): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 2017 Jul 11 10:42:24.361710 lacp: lacp_net_tx_data(215): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 2017 Jul 11 10:42:24.361721 lacp: lacp_net_tx_data(247): Ethernet1/3(0x1a002000): Tx LACP PDU len: 110 As:3f, Ps:3d 2017 Jul 11 10:42:24.361753 lacp: lacp_proto_get_state(969): IF Ethernet1/3(0x1a002000): end PartnerEnd(2): state TimeOut(1): enable_flag False 2017 Jul 11 10:42:24.361764 lacp: lacp_proto_restart_tx_timer(1802): lacp_proto_restart_tx_timer: got enable flag=0 before sending on interface Ethernet1/3(0x1a002000) 2017 Jul 11 10:42:24.361773 lacp: lacp_proto_restart_tx_timer(1825): lacp_proto_restart_tx_timer: flag 0 interface Ethernet1/3(0x1a002000) periodic_timer is fast 2017 Jul 11 10:42:24.361782 lacp: lacp_timer_start_w_chgd_time(681): lacp_timer_start_w_chgd_time: starting timer with time in ms = 1000 2017 Jul 11 10:42:24.361798 lacp: lacp_timer_start(637): Timer Started: Timer_Arg ([rid type IF-Rid: ifidx 0x1a002000: ch_num 0: event_id LACP_EV_PERIODIC_TRANSMIT_TIMER_EXPIRED(19): timer_id 400214: type PDUSendTime: active True: period_in_ms 1000]) 2017 Jul 11 10:42:24.361807 lacp: lacp_timer_start(638): Timer period=1 seconds 2017 Jul 11 10:42:24.361820 lacp: lacp_pkt_encode_pdu_helper(770): lacp_pkt_encode_pdu_helper: pkt_len=LACP_PDU_LEN=110 periodic_rate:1 2017 Jul 11 10:42:24.361833 lacp: lacp_pkt_encode_pdu_helper(797): lacp_pkt_encode_pdu_helper: if_idx=Ethernet1/4(0x1a003000) partner-mac=0-a6-ca-f3-c7-83 port_num=44 2017 Jul 11 10:42:24.361841 lacp: lacp_debug_wrapper_tl(1718): Executing [mcecm_api_is_pc_mcec] 2017 Jul 11 10:42:24.361849 lacp: lacp_debug_wrapper_tl(1718): input: if_index = [0x16000000] 2017 Jul 11 10:42:24.361857 lacp: lacp_debug_wrapper_tl(1718): Executing [mcecm_cache_is_pc_mcec] 2017 Jul 11 10:42:24.361865 lacp: lacp_debug_wrapper_tl(1718): output:0 2017 Jul 11 10:42:24.361879 lacp: lacp_pkt_encode_pdu_helper(842): 0x1a003000: Set short_timeout to periodic_rate:1 2017 Jul 11 10:42:24.361888 lacp: lacp_pkt_encode_pdu_helper(879): lacp_pkt_encode_pdu_helper: actor-port-state=7f agg=1 insync=1 coll=1 dis=1 active=1 short_timeout=1 2017 Jul 11 10:42:24.361899 lacp: lacp_pkt_encode_pdu_helper(906): lacp_pkt_encode_pdu_helper: if_idx=Ethernet1/4(0x1a003000) partner-port-state=0 agg=0 insync=0 coll=0 dis=0 active=0 short-timeout=0 2017 Jul 11 10:42:24.361910 lacp: lacp_pkt_encode_pdu_helper(910): lacp_pkt_encode_pdu_helper: if_idx=Ethernet1/4(0x1a003000) partner-mac=0-0-0-0-0-0 port_num=0 2017 Jul 11 10:42:24.361920 lacp: lacp_net_tx_data(206): lacp_net_tx_data: Sending buffer with length 110 2017 Jul 11 10:42:24.361930 lacp: lacp_net_tx_data(215): 01 01 01 14 ffff 2017 Jul 11 10:42:24.361940 lacp: lacp_net_tx_data(215): ffff 2017 Jul 11 10:42:24.361950 lacp: lacp_net_tx_data(215): 00 00 00 02 14 00 00 00 00 00 00 00 00 00 00 00 00 2017 Jul 11 10:42:24.361960 lacp: lacp_net_tx_data(215): 00 00 00 00 00 00 03 10 00 00 00 00 00 00 00 00 00 2017 Jul 11 10:42:24.361971 lacp: lacp_net_tx_data(215): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 2017 Jul 11 10:42:24.361981 lacp: lacp_net_tx_data(215): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 2017 Jul 11 10:42:24.361991 lacp: lacp_net_tx_data(215): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 2017 Jul 11 10:42:24.362001 lacp: lacp_net_tx_data(247): Ethernet1/4(0x1a003000): Tx LACP PDU len: 110 As:7f, Ps:00 2017 Jul 11 10:42:24.362022 lacp: lacp_proto_get_state(969): IF Ethernet1/4(0x1a003000): end PartnerEnd(2): state TimeOut(1): enable_flag False 2017 Jul 11 10:42:24.362032 lacp: lacp_proto_restart_tx_timer(1802): lacp_proto_restart_tx_timer: got enable flag=0 before sending on interface Ethernet1/4(0x1a003000) 2017 Jul 11 10:42:24.362042 lacp: lacp_proto_restart_tx_timer(1825): lacp_proto_restart_tx_timer: flag 0 interface Ethernet1/4(0x1a003000) periodic_timer is fast 2017 Jul 11 10:42:24.362050 lacp: lacp_timer_start_w_chgd_time(681): lacp_timer_start_w_chgd_time: starting timer with time in ms = 1000 2017 Jul 11 10:42:24.362062 lacp: lacp_timer_start(637): Timer Started: Timer_Arg ([rid type IF-Rid: ifidx 0x1a003000: ch_num 0: event_id LACP_EV_PERIODIC_TRANSMIT_TIMER_EXPIRED(19): timer_id 399340: type PDUSendTime: active True: period_in_ms 1000])
팁
피어에서 LACP 패킷을 수신하는지 확인합니다. 예를 들어 Ethernet1/3 인터페이스는 LACP 패킷을 수신하지만 Ethernet1/4는 다음을 수신하지 않습니다.
2017 Jul 11 10:42:25.641920 lacp: lacp_net_get_pkt_info(746): Packet received on phy_if_idx Ethernet1/3(0x1a002000): log_if_idx Ethernet1/3(0x1a002000): pkt_len 124 l2 header len 14 2017 Jul 11 10:42:25.641937 lacp: lacp_net_process_rx_data(480): Ethernet1/3(0x1a002000): Rx LACP PDU len: 124 As:3f, Ps:3d
확인 9
이 출력에서 인터페이스 Ethernet1/4는 Port-Channel의 멤버이지만 개별 모드(스위치 측에서 일시 중단)에 있습니다.
ciscofcm01-A(fxos)# show lacp internal event-history interface ethernet 1/4
>>>>FSM: <Ethernet1/4> has 549 logged transitions<<<<<
1) FSM:<Ethernet1/4> Transition at 385779 usecs after Wed Jul 5 13:13:03 2017
Previous state: [LACP_ST_PORT_IS_DOWN_OR_LACP_IS_DISABLED]
Triggered event: [LACP_EV_CLNUP_PHASE_II]
Next state: [LACP_ST_PORT_IS_DOWN_OR_LACP_IS_DISABLED]
2) FSM:<Ethernet1/4> Transition at 955546 usecs after Wed Jul 5 13:13:03 2017
Previous state: [LACP_ST_PORT_IS_DOWN_OR_LACP_IS_DISABLED]
Triggered event: [LACP_EV_LACP_ENABLED_AND_PORT_UP]
Next state: [LACP_ST_DETACHED_LAG_NOT_DETERMINED]
3) FSM:<Ethernet1/4> Transition at 962224 usecs after Wed Jul 5 13:13:10 2017
Previous state: [LACP_ST_DETACHED_LAG_NOT_DETERMINED]
Triggered event: [LACP_EV_RECEIVE_PARTNER_PDU_TIMED_OUT]
Next state: [FSM_ST_NO_CHANGE]
4) FSM:<Ethernet1/4> Transition at 963838 usecs after Wed Jul 5 13:13:13 2017
Previous state: [LACP_ST_DETACHED_LAG_NOT_DETERMINED]
Triggered event: [LACP_EV_RECEIVE_PARTNER_PDU_TIMED_OUT]
Next state: [FSM_ST_NO_CHANGE]
5) FSM:<Ethernet1/4> Transition at 964002 usecs after Wed Jul 5 13:13:13 2017
Previous state: [LACP_ST_DETACHED_LAG_NOT_DETERMINED]
Triggered event: [LACP_EV_RECEIVE_PARTNER_PDU_TIMED_OUT_II_INDIVIDUAL]
Next state: [LACP_ST_INDIVIDUAL_OR_DEFAULT]
6) FSM:<Ethernet1/4> Transition at 735923 usecs after Wed Jul 5 13:13:36 2017
Previous state: [LACP_ST_INDIVIDUAL_OR_DEFAULT]
Triggered event: [LACP_EV_UNGRACEFUL_DOWN]
Next state: [LACP_ST_PORT_IS_DOWN_OR_LACP_IS_DISABLED]
확인 10
이 출력에서 Ethernet1/3 인터페이스는 작동하며 PortChannel1의 멤버이지만 Ethernet1/4는 PortChannel1의 멤버입니다. Ethernet1/3은 (tx) 패킷을 전송하고 (rx) 패킷을 수신하지만, Ethernet1/4는 (rx)만 전송하고 tx는 수신하지 않습니다.
ciscofcm01-A(fxos)# debug lacp pkt ciscofcm01-A(fxos)# 2017 Jul 11 11:04:05.278736 lacp: lacp_net_process_rx_data(480): Ethernet1/3(0x1a002000): Rx LACP PDU len: 124 As:3f, Ps:3d 2017 Jul 11 11:04:05.602855 lacp: lacp_net_tx_data(247): Ethernet1/3(0x1a002000): Tx LACP PDU len: 110 As:3f, Ps:3d 2017 Jul 11 11:04:05.983134 lacp: lacp_net_tx_data(247): Ethernet1/4(0x1a003000): Tx LACP PDU len: 110 As:7f, Ps:00 2017 Jul 11 11:04:06.249929 lacp: lacp_net_process_rx_data(480): Ethernet1/3(0x1a002000): Rx LACP PDU len: 124 As:3f, Ps:3d 2017 Jul 11 11:04:06.602815 lacp: lacp_net_tx_data(247): Ethernet1/3(0x1a002000): Tx LACP PDU len: 110 As:3f, Ps:3d 2017 Jul 11 11:04:06.992812 lacp: lacp_net_tx_data(247): Ethernet1/4(0x1a003000): Tx LACP PDU len: 110 As:7f, Ps:00 2017 Jul 11 11:04:07.163780 lacp: lacp_net_process_rx_data(480): Ethernet1/3(0x1a002000): Rx LACP PDU len: 124 As:3f, Ps:3d 2017 Jul 11 11:04:07.602814 lacp: lacp_net_tx_data(247): Ethernet1/3(0x1a002000): Tx LACP PDU len: 110 As:3f, Ps:3d 2017 Jul 11 11:04:08.002817 lacp: lacp_net_tx_data(247): Ethernet1/4(0x1a003000): Tx LACP PDU len: 110 As:7f, Ps:00 2017 Jul 11 11:04:08.102006 lacp: lacp_net_process_rx_data(480): Ethernet1/3(0x1a002000): Rx LACP PDU len: 124 As:3f, Ps:3d 2017 Jul 11 11:04:08.612810 lacp: lacp_net_tx_data(247): Ethernet1/3(0x1a002000): Tx LACP PDU len: 110 As:3f, Ps:3d 2017 Jul 11 11:04:09.002811 lacp: lacp_net_tx_data(247): Ethernet1/4(0x1a003000): Tx LACP PDU len: 110 As:7f, Ps:00 2017 Jul 11 11:04:09.091937 lacp: lacp_net_process_rx_data(480): Ethernet1/3(0x1a002000): Rx LACP PDU len: 124 As:3f, Ps:3d 2017 Jul 11 11:04:09.622810 lacp: lacp_net_tx_data(247): Ethernet1/3(0x1a002000): Tx LACP PDU len: 110 As:3f, Ps:3d 2017 Jul 11 11:04:10.002807 lacp: lacp_net_tx_data(247): Ethernet1/4(0x1a003000): Tx LACP PDU len: 110 As:7f, Ps:00 2017 Jul 11 11:04:10.004411 lacp: lacp_net_process_rx_data(480): Ethernet1/3(0x1a002000): Rx LACP PDU len: 124 As:3f, Ps:3d 2017 Jul 11 11:04:10.632806 lacp: lacp_net_tx_data(247): Ethernet1/3(0x1a002000): Tx LACP PDU len: 110 As:3f, Ps:3d 2017 Jul 11 11:04:10.854094 lacp: lacp_net_process_rx_data(480): Ethernet1/3(0x1a002000): Rx LACP PDU len: 124 As:3f, Ps:3d 2017 Jul 11 11:04:11.002789 lacp: lacp_net_tx_data(247): Ethernet1/4(0x1a003000): Tx LACP PDU len: 110 As:7f, Ps:00 2017 Jul 11 11:04:11.642807 lacp: lacp_net_tx_data(247): Ethernet1/3(0x1a002000): Tx LACP PDU len: 110 As:3f, Ps:3d 2017 Jul 11 11:04:11.714199 lacp: lacp_net_process_rx_data(480): Ethernet1/3(0x1a002000): Rx LACP PDU len: 124 As:3f, Ps:3d
자세한 내용은 다음 문서를 참조하십시오.
Q. Show Tech 결과에서 FXOS 번들 버전을 찾는 방법은 무엇입니까?
방법 1
FPRM tar 파일에서 FPRM_A_TechSupport.tar.gz 파일의 내용을 추출합니다. 그런 다음 sam_techsupportinfo 파일을 열고 Package-Verse를 검색합니다.
FPR4140-A# show fabric-interconnect firmware
Fabric Interconnect A:
Running-Kern-Vers: 5.0(3)N2(4.11.74)
Running-Sys-Vers: 5.0(3)N2(4.11.74)
Package-Vers: 2.1(1.77)
Startup-Kern-Vers: 5.0(3)N2(4.11.74)
Startup-Sys-Vers: 5.0(3)N2(4.11.74)
Act-Kern-Status: Ready
Act-Sys-Status: Ready
Bootloader-Vers:
2단계
FPM tar 파일에서 FPRM_A_TechSupport.tar.gz 파일의 내용을 추출합니다. 그런 다음 /var/sysmgr/sam_logs/svc_sam_dme.log 파일을 열고 aInPlatformVersion 키워드를 검색합니다.
Q. MIO는 어떻게 인터페이스 정보(추가/제거)를 블레이드 애플리케이션(FTD, ASA)에 전파합니까?
MIO 앱 에이전트 구성 요소를 사용합니다.
예를 들어 MIO에서 새 포트 채널이 FTD에 할당되는 경우
FTD app-agent debug는 다음을 보여줍니다.
firepower# debug app-agent 255 appagent : part 0 : ftd_001_JAD19500BAB0Z690F2.interfaceMapping.update appagent : part 1 : ssp-xml:3 appagent : part 2 : 7 appagent : part 3 : appAG appagent : part 4 : <interfaceMappingConfigUpdateRequest><interfaceMapping action="insert"><externalPort><portName>Port-channel11</portName><vlan>1011</vlan><role>data</role><mode>individual</mode><mc_mode>individual</mc_mode><status>down</status><speed>1000</speed><mac type="system">5897.bdb9.367e</mac></externalPort><internalPort><bladeVNIC>9</bladeVNIC>
<bladeVNIC>22</bladeVNIC></internalPort></interfaceMapping></interfaceMappingConfigUpdateRequest> appagent : Process the request message appagent : It is an update request command appagent : Invoke request msg handler for cmd interfaceMapping.update appagent : Processing InterfaceMapping Update Message appagent : Creating Interface Mapping Structure. appagent : Processing the tag externalPort. appagent : ================================ appagent : PortName=Port-channel11 appagent : ftw capability=0 appagent : no available ftw peers appagent : cleaning external_port_ftw_peers_t appagent : Sending Response message for Interface Mapping update Message appagent : Send response message to appAG appagent : resp_msg->cmdName =appAG.interfaceMapping.update appagent : resp_msg->content_version =ssp-xml:3 appagent : resp_msg->msgId =7 appagent : resp_msg->statuscode =100 appagent : resp_msg->data =<interfaceMappingConfigUpdateResponse> <response> <code>100</code> <message>Request success</message> </response> </interfaceMappingConfigUpdateResponse> appagent : part 0 : ftd_001_JAD19500BAB0Z690F2.interfaceStatus.update appagent : part 1 : ssp-xml:3 appagent : part 2 : 8 appagent : part 3 : appAG appagent : part 4 : <interfaceStatusUpdateRequest><interface><interfaceName>Port-channel11</interfaceName><externalOperationalStatus>down</externalOperationalStatus><internalOperationalStatus>up</internalOperationalStatus></interface></interfaceStatusUpdateRequest> appagent : Process the request message appagent : It is an update request command appagent : Invoke request msg handler for cmd interfaceStatus.update appagent : Processing Interface Status Update Request. appagent : The Fxos version is 2.1.1 or newer appagent : Parsing interface status update request message for FXOS > 211 appagent : Parsing Interface Status Req. appagent : Interface Status Successfully Updated. appagent : Sending Response for Interface Status Update Request appagent : Send response message to appAG appagent : resp_msg->cmdName =appAG.interfaceStatus.update appagent : resp_msg->content_version =ssp-xml:3 appagent : resp_msg->msgId =8 appagent : resp_msg->statuscode =100 appagent : resp_msg->data =<interfaceStatusUpdateResponse> <response> <code>100</code> <message>Request success</message> </response> </interfaceStatusUpdateResponse>
Q. Firepower 섀시의 RMA의 경우 어떤 일련 번호(SN)를 사용해야 합니까?
firepower 섀시에는 여러 SN이 있습니다. RMA 요청에 사용된 것은 다음 출력에서 가져올 수 있습니다.
FP4120-5-A# scope chassis 1
FP4120-5-A /chassis # show inventory
Chassis PID Vendor Serial (SN) HW Revision
---------- --------------- ----------------- ----------- -----------
1 FPR-4120-K9 Cisco Systems Inc FLM12345KL6 0
또는:
FP4120-5-A# connect local-mgmt FP4120-5-A(local-mgmt)# show license all Smart Licensing Status ====================== Smart Licensing is ENABLED Registration: Status: UNREGISTERED Export-Controlled Functionality: Not Allowed License Authorization: Status: No Licenses in Use License Usage ============== No licenses in use Product Information =================== UDI: PID:FPR-4120-SUP,SN:JAD19500BAB
또는:
FP4120-5-A# scope license FP4120-5-A /license # show license all Smart Licensing Status ====================== Smart Licensing is ENABLED Registration: Status: UNREGISTERED Export-Controlled Functionality: Not Allowed License Authorization: Status: No Licenses in Use License Usage ============== No licenses in use Product Information =================== UDI: PID:FPR-4120-SUP,SN:JAD19500BAB
Q. 서로 다른 2개의 FXOS 섀시 간에 SSD1을 교체할 수 있습니까?
간단히 말해 no입니다. SSD1에는 애플리케이션 이미지(예: FTD 또는 ASA)가 포함됩니다. SSD1을 섀시에서 꺼낸 다음 다른 섀시에 꽂으면 모듈이 UP되지 않으며 다음과 같은 오류가 나타납니다.
중요 F1548 2017-11-08T11:36:40.095 427280 블레이드 스왑이 슬롯 1에서 탐지됨
보안 모듈 이미지 불일치
서버 1/1에 로컬 디스크 1이 없습니다.
Q. 섀시 전력 소비량은 어떻게 확인합니까?
FXOS 2.2.1 버전에서처럼 show environment summary 명령을 사용할 수 있습니다.
FPR4100-1 /chassis # show environment summary
Chassis INFO :
Total Power Consumption: 440.000000
Inlet Temperature (C): 21.000000
CPU Temperature (C): 39.000000
Last updated Time: 2018-07-01T09:39:55.157
PSU 1:
Type: AC
Input Feed Status: Ok
12v Output Status: Ok
Overall Status: Operable
PSU 2:
Type: AC
Input Feed Status: N/A
12v Output Status: N/A
Overall Status: Removed
FAN 1
Fan Speed RPM (RPM): 12110
Speed Status: Ok
Overall Status: Operable
FAN 2
Fan Speed RPM (RPM): 12110
Speed Status: Ok
Overall Status: Operable
FAN 3
Fan Speed RPM (RPM): 12100
Speed Status: Ok
Overall Status: Operable
추가 정보 확인:
Q. 부트로더 버전을 확인하는 방법은?
FPR-4110-7-A# scope chassis 1
FPR-4110-7-A /chassis # scope server 1
FPR-4110-7-A /chassis/server # scope adapter 1
FPR-4110-7-A /chassis/server/adapter # show version detail
Adapter 1:
Running-Vers: 5.3(1.91)
Package-Vers: 2.3(1.88)
Update-Status: Ready
Activate-Status: Ready
Bootloader-Update-Status: Ready
Startup-Vers: 5.3(1.91)
Backup-Vers: 5.3(1.48)
Bootloader-Vers: MF-111-234949
Q. 부트로더를 업그레이드하려면 어떻게 해야 합니까?
FXOS 2.3.1.58 이상 설치 후, 시스템에 보안 어플라이언스에서 어댑터 펌웨어 업그레이드가 필요하다는 중대한 결함이 표시될 수 있습니다.
Critical F1715 2017-05-11T11:43:33.121 339561 Adapter 1 on Security Module 1 requires a critical firmware upgrade. Please see Adapter Bootloader Upgrade instructions in the FXOS Release Notes posted with this release.
부트로더 업그레이드 절차는 다음 링크에서 설명합니다.
https://www.cisco.com/c/en/us/td/docs/security/firepower/fxos/fxos231/release/notes/fxos231_rn.html#pgfId-173826
부트로더를 업그레이드하는 동안 아래의 오류가 발생하면 'force' 옵션을 사용할 수 있습니다.
FPR-4110-7-A# scope chassis 1
FPR-4110-7-A /chassis # scope server 1
FPR-4110-7-A /chassis/server # scope adapter 1/1/1
FPR-4110-7-A /chassis/server/adapter # show image
Name Type Version
--------------------------------------------- -------------------- -------
fxos-m83-8p40-cruzboot.4.0.1.62.bin Adapter Boot 4.0(1.62)
fxos-m83-8p40-vic.4.0.1.51.bin Adapter 4.0(1.51)
fxos-m83-8p40-vic.5.3.1.2.bin Adapter 5.3(1.2)
fxos-m83-8p40-vic.5.3.1.48.bin Adapter 5.3(1.48)
fxos-m83-8p40-vic.5.3.1.91.bin Adapter 5.3(1.91)
FPR-4110-7-A /chassis/server/adapter # update boot-loader 4.0(1.62)
Warning: Please DO NOT reboot blade or chassis during uprgade, otherwise, it may cause adapter UNUSABLE
After upgrade completed, blade must be power cycled automatically
FPR-4110-7-A /chassis/server/adapter* # commit-buffer
Error: Update failed: [This adaptor is not applicable for boot-loader upgrade.]
Q. 절대 SSH 시간 초과를 비활성화하는 방법
이 기능은 랩 테스트 및 트러블슈팅 중에 유용합니다. 이 절대 시간 초과는 0이 아닌 보안 모범 사례이므로 사용자 환경에서 일시적으로 수행되는 경우 주의해야 합니다.
FPR-4115-A# scope security
FPR-4115-A /security # scope default-auth
FPR-4115-A /security/default-auth # show detail
Default authentication:
Admin Realm: Local
Operational Realm: Local
Web session refresh period(in secs): 600
Idle Session timeout(in secs) for web, ssh, telnet sessions: 3600
Absolute Session timeout(in secs) for web, ssh, telnet sessions: 3600
Serial Console Idle Session timeout(in secs): 3600
Serial Console Absolute Session timeout(in secs): 3600
Admin Authentication server group:
Operational Authentication server group:
Use of 2nd factor: No
FPR-4115-A /security/default-auth # set absolute-session-timeout 0
FPR-4115-A /security/default-auth* # commit-buffer
FPR-4115-A /security/default-auth # show detail
Default authentication:
Admin Realm: Local
Operational Realm: Local
Web session refresh period(in secs): 600
Idle Session timeout(in secs) for web, ssh, telnet sessions: 3600
Absolute Session timeout(in secs) for web, ssh, telnet sessions: 0
Serial Console Idle Session timeout(in secs): 3600
Serial Console Absolute Session timeout(in secs): 3600
Admin Authentication server group:
Operational Authentication server group:
Use of 2nd factor: No
Q. 섀시 수퍼바이저(컨트롤 플레인)로 향하는 LACP 패킷을 캡처하는 방법은 무엇입니까?
Firepower 4100/9300 섀시 수퍼바이저(컨트롤 플레인)로 향하는 LACP 패킷은 특정 패킷의 데이터 섹션 내부에 캡슐화되며, ethanalyzer 명령을 사용하여 내부 인바운드-hi 인터페이스에서 캡처할 수 있습니다. LACP PDU 바이트는 값이 01 80 C2 00 00 02(IEEE 802.3 Slow_Protocols_Multicast 주소)인 바이트부터 데이터 섹션이 끝날 때까지 포함됩니다.
firepower# connect fxos
...
firepower(fxos)# ethanalyzer local interface inbound-hi limit-captured-frames 10000 limit-frame-size 9000 detail
Capturing on 'eth4'
Frame 1: 188 bytes on wire (1504 bits), 188 bytes captured (1504 bits) on interface 0
Interface id: 0 (eth4)
Interface name: eth4
Encapsulation type: Ethernet (1)
Arrival Time: Dec 5, 2023 09:16:06.736180828 UTC
[Time shift for this packet: 0.000000000 seconds]
Epoch Time: 1701767766.736180828 seconds
[Time delta from previous captured frame: 0.000000000 seconds]
[Time delta from previous displayed frame: 0.000000000 seconds]
[Time since reference or first frame: 0.000000000 seconds]
Frame Number: 1
Frame Length: 188 bytes (1504 bits)
Capture Length: 188 bytes (1504 bits)
[Frame is marked: False]
[Frame is ignored: False]
[Protocols in frame: eth:ethertype:vlan:ethertype:data]
Ethernet II, Src: 02:10:18:a3:4f:f5 (02:10:18:a3:4f:f5), Dst: 58:97:bd:b9:36:4e (58:97:bd:b9:36:4e)
Destination: 58:97:bd:b9:36:4e (58:97:bd:b9:36:4e)
Address: 58:97:bd:b9:36:4e (58:97:bd:b9:36:4e)
.... ..0. .... .... .... .... = LG bit: Globally unique address (factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Source: 02:10:18:a3:4f:f5 (02:10:18:a3:4f:f5)
Address: 02:10:18:a3:4f:f5 (02:10:18:a3:4f:f5)
.... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Type: 802.1Q Virtual LAN (0x8100)
802.1Q Virtual LAN, PRI: 0, DEI: 0, ID: 4048
000. .... .... .... = Priority: Best Effort (default) (0)
...0 .... .... .... = DEI: Ineligible
.... 1111 1101 0000 = ID: 4048
Type: Unknown (0xde08)
Data (170 bytes)
0000 b8 50 20 04 00 00 00 00 00 00 00 00 00 00 81 00 .P .............
0010 00 00 00 00 00 04 09 04 cd 00 00 00 00 00 00 00 ................
0020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01 80 ................
0030 c2 00 00 02 58 97 bd b9 36 51 88 09 01 01 01 14 ....X...6Q......
0040 80 00 58 97 bd b9 36 4d 00 28 80 00 00 44 3f 00 ..X...6M.(...D?.
0050 00 00 02 14 80 00 00 17 df d6 ec 00 00 33 80 00 .............3..
0060 02 2c 3d 00 00 00 03 10 00 00 00 00 00 00 00 00 .,=.............
0070 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
0080 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
0090 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00a0 00 00 00 00 00 00 00 00 00 00 ..........
Data: b85020040000000000000000000081000000000000040904...
16진수 덤프는 온라인 툴을 사용하여 PCAP로 변환할 수 있습니다.
Q. SSD 정보를 찾는 방법은?
섀시 수퍼바이저 내부 SSD 정보는 FN72077의 해결 방법/솔루션, 1단계에서 언급된 모든 FXOS 버전에서 사용할 수 있습니다.
KSEC-FPR4112-4 # scope chassis 1
KSEC-FPR4112-4 /chassis # show sup version detail
SUP FIRMWARE:
ROMMON:
Running-Vers: 1.0.15
Package-Vers: 1.0.18
Activate-Status: Ready
Upgrade Status: SUCCESS
FPGA:
Running-Vers: 2.00
Package-Vers: 1.0.18
Activate-Status: Ready
SSD:
Running-Vers: MU03
Model: Micron_M500IT_MTFDDAT128MBD
보안 엔진(블레이드) SSD:
KSEC-FPR4112-4# show server storage detail
Server 1/1:
<output skipped>
RAID Controller 1:
Type: SATA
Vendor: Cisco Systems Inc
Model: FPR4K-PT-01
Serial: JAD260508TZ
HW Revision:
PCI Addr: 00:31.2
Raid Support:
OOB Interface Supported: No
Rebuild Rate: N/A
Controller Status: Unknown
Local Disk 1:
Vendor: INTEL
Model: SSDSC2KG48
Serial: PHYG109603PA480BGN
HW Rev: 0
Operability: Operable
Presence: Equipped
Size (MB): 400000
Drive State: Online
Power State: Active
Link Speed: 6 Gbps
Device Type: SSD
Local Disk 2:
Vendor: INTEL
Model: SSDSC2KG96
Serial: PHYG143301JG960CGN
HW Rev: 0
Operability: Operable
Presence: Equipped
Size (MB): 800000
Drive State: Online
Power State: Active
Link Speed: 6 Gbps
Device Type: SSD
Local Disk Config Definition:
Mode: No RAID
Description:
Protect Configuration: No
Q. FXOS(Internal Switch) 캡처를 구성하는 방법
Configure and Verify Secure Firewall and Monitoring(보안 방화벽 및 Firepower 내부 스위치 캡처 구성 및 확인) 문서를 참조하십시오.
참조
개정 이력
| 개정 | 게시 날짜 | 의견 |
|---|---|---|
5.0 |
06-Apr-2024 |
콘텐츠를 업데이트했습니다. |
2.0 |
05-Jul-2023 |
제목, 소개, 메모, 머리글 서식 업데이트
제거된 라틴어 약어 및 방향 언어
PII가 없음을 확인했습니다. |
1.0 |
26-May-2020 |
최초 릴리스 |
피드백