この製品のマニュアルセットは、偏向のない言語を使用するように配慮されています。このマニュアルセットでの偏向のない言語とは、年齢、障害、性別、人種的アイデンティティ、民族的アイデンティティ、性的指向、社会経済的地位、およびインターセクショナリティに基づく差別を意味しない言語として定義されています。製品ソフトウェアのユーザーインターフェイスにハードコードされている言語、RFP のドキュメントに基づいて使用されている言語、または参照されているサードパーティ製品で使用されている言語によりドキュメントに例外が存在する場合があります。シスコのインクルーシブランゲージに対する取り組みの詳細は、こちらをご覧ください。
このドキュメントは、米国シスコ発行ドキュメントの参考和訳です。リンク情報につきましては、日本語版掲載時点で、英語版にアップデートがあり、リンク先のページが移動/変更されている場合がありますことをご了承ください。あくまでも参考和訳となりますので、正式な内容については米国サイトのドキュメントを参照ください。
この章では、PA-4T ポート アダプタをサポート対象プラットフォームから取り外す手順について、さらに、新規または交換用ポート アダプタを取り付ける手順について説明します。この章で説明する内容は、次のとおりです。
• 「ルータの電源をオフにした場合は、30 秒以上経ってから再度電源を入れてください。」
• 「活性挿抜」
(注) ポート アダプタ スロットを使用しない場合、ルータまたはスイッチを EMI(電磁波干渉)放射規格に適合させ、ポート アダプタ周辺のエアフローが適切になるように、空スロットにブランク ポート アダプタを取り付けておく必要があります。したがって、未使用スロットに新しいポート アダプタを取り付ける場合、最初にブランク ポート アダプタを取り外す必要があります。
各ポート アダプタの回路基板は、金属フレームに搭載されており、静電破壊を受けやすくなっています。
一部のプラットフォームでは、ポート アダプタの活性挿抜(Online Insertion and Removal; OIR)が可能です。したがって、Cisco 7200 シリーズ ルータでは、PA-4T の取り外し/取り付け時に、ルータの電源を切る必要はありません。
VIP は活性挿抜対応ですが、各ポート アダプタは活性挿抜対応ではありません。ポート アダプタを交換する場合には、まずシャーシから VIP を取り外し、そのあとで必要に応じてポート アダプタを交換する必要があります。新しいポート アダプタを取り付ける VIP にブランク ポート アダプタが取り付けられている場合は、まずシャーシから VIP を取り外し、そのあとでブランク ポート アダプタを取り外す必要があります。
アクティブなトラフィックが発生しているポート アダプタを取り外す前に、システムをシャットダウンすることを推奨します。ポートでトラフィックをやりとりしている最中にモジュールを取り外すと、システム破壊が生じる可能性があります。モジュールを取り付けると、ポートを稼働状態に戻すことができます。
(注) ルータまたはスイッチからモジュールを取り外すと、活性挿抜により、取り外したモジュールのすべてのアクティブ インターフェイスが管理上のシャットダウンに切り替えられます。
活性挿抜により、システムの稼働中にモジュールの取り付けおよび取り外しを行うことができます。ソフトウェアに通知したり、システムの電源をシャットダウンする必要はありません。ただし、取り外し中のモジュールには、トラフィックが発生しないようにしてください。活性挿抜は、ネットワーク上のエンド ユーザに影響を与えず、すべてのルーティング情報を保持しながら、セッションを維持する方法です。
次に、活性挿抜の基本的な機能について説明します。サポート対象プラットフォームにおける特定のモジュールの取り付けおよび取り外し手順については、「ポート アダプタの取り外し/取り付け」を参照してください。
各モジュールには、ルータ接続用のバス コネクタが 1 つあります。コネクタには、3 種類の長さの階段状のピンがあり、モジュールに接続すると、システムに固有の信号を送信します。システムでは、受信信号およびその受信順序を確認して、モジュールがシステムから取り外されたのか、または取り付けられたのかを判断します。システムは、これらの信号から、新しいインターフェイスを再度初期化するか、または取り外されたインターフェイスをシャットダウンするかを判断します。
たとえば、モジュールを取り付ける場合、一番長いピンが最初にモジュールに接触して、一番短いピンが最後に接触します。システムは、この信号および受信順序を認識します。
モジュールを取り外す場合または取り付ける場合、ピンが信号を送信して、システムに変更を通知します。すると、ルータは次の処理を実行します。
1. システムを迅速にスキャンして、コンフィギュレーションの変更を確認します。
2. 新しく取り付けられたポート アダプタを初期化するか、または空のインターフェイスを管理上のシャットダウンにします。
3. 以前設定されていたモジュール上のインターフェイスを、すべて以前の状態に戻します。新しく取り付けられたインターフェイスは、起動時に未設定ではあるが存在していたものとして、管理上のシャットダウン状態にされます。同じタイプのモジュールをスロットに再度取り付けた場合、モジュールのポートは、当初取り付けられていた同じタイプのモジュールのポートの数まで設定され、オンラインになります。
(注) インストレーションを開始する前に、「インストレーションの準備」を参照し、必要な部品および工具を確認してください。
ポート アダプタの取り外し/取り付けを行うときは、次の警告および注意に従ってください。
(注) ポート アダプタ レバーまたは他の固定機構をロックの位置に移動できない場合、ポート アダプタはミッドプレーンに完全に装着されていません。ポート アダプタをスロットから半分ほど注意深く引き抜き、再び挿入してから、ポート アダプタのレバー(または他の機構)をロック位置に移動してください。
警告 作業中は、カードの静電破壊を防ぐため、必ず静電気防止用リスト ストラップを着用してください。感電する危険があるので、手や金属工具がミッドプレーンに直接触れないようにしてください。
ここでは、次のサポート対象プラットフォームごとに、ポート アダプタの取り付け/取り外し手順を、一連の図で説明します。ここでは、次の内容について説明します。
• 「Cisco 7200 シリーズ ― ポート アダプタの取り外しおよび取り付け」
• 「VIP ― ポート アダプタの取り外しおよび取り付け」
1 台の PA-4T では、同期シリアル接続を 4 つまで設定できます。ポート アダプタにはハンドルがありますが、各ポート アダプタ前面プレートの細部を示すために、図ではハンドルを省略しています。
PA-4T にシリアル ケーブルを接続する手順は次のとおりです。
ステップ 1 適切なシリアル ケーブルを PA-4T のレセプタクルに直接接続し、ストレインレリーフ ネジを締めます(図3-2 を参照)。
図3-2 PA-4T シリアル ケーブルの接続 ― 水平方向(ハンドルは省略)
ステップ 2 シリアル ケーブルのネットワーク側を DSU、CSU、DTE、またはその他の外部同期シリアル機器に接続し、ストレインレリーフ ネジを締めます。