Configuration et vérification de la sécurité de couche 3 dans les WLAN Wi-Fi 6E

Mis à jour:11 août 2023
ID du document:220729

Langage exempt de préjugés

Dans le cadre de la documentation associée à ce produit, nous nous efforçons d’utiliser un langage exempt de préjugés. Dans cet ensemble de documents, le langage exempt de discrimination renvoie à une langue qui exclut la discrimination en fonction de l’âge, des handicaps, du genre, de l’appartenance raciale de l’identité ethnique, de l’orientation sexuelle, de la situation socio-économique et de l’intersectionnalité. Des exceptions peuvent s’appliquer dans les documents si le langage est codé en dur dans les interfaces utilisateurs du produit logiciel, si le langage utilisé est basé sur la documentation RFP ou si le langage utilisé provient d’un produit tiers référencé. Découvrez comment Cisco utilise le langage inclusif.

À propos de cette traduction

Cisco a traduit ce document en traduction automatisée vérifiée par une personne dans le cadre d’un service mondial permettant à nos utilisateurs d’obtenir le contenu d’assistance dans leur propre langue. Il convient cependant de noter que même la meilleure traduction automatisée ne sera pas aussi précise que celle fournie par un traducteur professionnel.

    Introduction

    Ce document décrit comment configurer la sécurité de couche 3 dans les WLAN Wi-Fi 6E et ce à quoi s'attendre sur différents clients.

    Conditions préalables

    Exigences

    Cisco vous recommande de prendre connaissance des rubriques suivantes :

    • Contrôleurs LAN sans fil Cisco (WLC) 9800
    • Points d'accès Cisco prenant en charge le Wi-Fi 6E. 
    • Norme IEEE 802.11ax.
    • Outils : Wireshark v4.0.6

    Composants utilisés

    Les informations contenues dans ce document sont basées sur les versions de matériel et de logiciel suivantes :

    • WLC 9800-CL avec IOS® XE 17.9.4.
    • AP C9136, CW9162, CW9164 et CW9166.
    • Clients Wi-Fi 6E :
      • Carte Lenovo X1 Carbon Gen11 avec Intel AX211 Wi-Fi 6 et 6E avec pilote version 22.200.2(1).
      • Téléphone portable Pixel 6a avec Android 13 ;
      • Téléphone portable Samsung S23 avec Android 13.

    The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. Si votre réseau est en ligne, assurez-vous de bien comprendre l’incidence possible des commandes.

    Informations générales

    Il est important de savoir que le Wi-Fi 6E n'est pas une norme entièrement nouvelle, mais une extension. À sa base, le Wi-Fi 6E est une extension de la norme sans fil Wi-Fi 6 (802.11ax) dans la bande de radiofréquences de 6 GHz.

    Le Wi-Fi 6E repose sur le Wi-Fi 6, qui est la dernière génération de la norme Wi-Fi, mais seuls les périphériques et applications Wi-Fi 6E peuvent fonctionner dans la bande 6 GHz.

    La sécurité de couche 3 dans WiFi 6E est la même que dans WiFi 5 ou 6, est un sentiment que le flux d'authentification Web ne diffère pas dans aucun scénario. La seule différence avec la sécurité de couche 3 dans WiFI 6E est le fait que tout WLAN dans WiFI 6E doit avoir une sécurité de couche 2 configurée avec WPA3 et PMF qui sont obligatoires dans WiFi 6E.

    Pour en savoir plus sur la sécurité de la couche 2 WiFi 6E, consultez le document : Configure and Verify Wi-Fi 6E WLAN Layer 2 Security . 

    Authentification Web 

    L'authentification Web est une solution de sécurité de couche 3 conçue pour fournir un accès invité facile et sécurisé aux hôtes sur WLAN avec authentification ouverte ou méthodes de sécurité de couche 2 appropriées.

    Voici les différents types de méthodes d'authentification Web :

    • Local Web Authentication (LWA) : configuré en tant que sécurité de couche 3 sur le contrôleur, la page d'authentification Web et la liste de contrôle d'accès de pré-authentification sont configurées localement sur le contrôleur. Le contrôleur intercepte le trafic htttp(s) et redirige le client vers la page Web interne pour authentification. Les informations d'identification entrées par le client sur la page de connexion sont authentifiées par le contrôleur localement ou via un serveur RADIUS ou LDAP.

    • External Web Authentication (EWA) : configuré en tant que sécurité de couche 3 sur le contrôleur, le contrôleur intercepte le trafic http(s) et redirige le client vers la page de connexion hébergée sur le serveur Web externe. Les informations d'identification entrées par le client sur la page de connexion sont authentifiées par le contrôleur localement ou via un serveur RADIUS ou LDAP. La liste de contrôle d'accès de pré-authentification est configurée de manière statique sur le contrôleur.

    • Central Web Authentication (CWA) : configurés principalement en tant que sécurité de couche 2 sur le contrôleur, l'URL de redirection et la liste de contrôle d'accès de pré-authentification résident sur ISE et sont envoyés au contrôleur lors de l'authentification de couche 2. Le contrôleur redirige tout le trafic Web du client vers la page de connexion ISE. ISE valide les informations d'identification saisies par le client via HTTPS et authentifie l'utilisateur.

    Vous trouverez plus de détails dans le document Authentification Web sur les contrôleurs de la gamme Cisco Catalyst 9800 .

    Traditionnellement, les points d'accès Wi-Fi et les WLAN invités utilisent la sécurité ouverte sans chiffrement ni authentification. La certification Wi-Fi CERTIFIED Enhanced Open définit une meilleure confidentialité des données dans les réseaux Wi-Fi ouverts.

    Cette certification est basée sur le protocole Opportunistic Wireless Encryption (OWE). OWE est défini dans la norme IETF RFC 8110. Le protocole OWE intègre des mécanismes de cryptographie établis pour fournir à chaque utilisateur un cryptage individuel unique, protégeant ainsi l'échange de données entre l'utilisateur et le point d'accès.

    L'OWE utilise le cryptage basé sur les algorithmes Diffie-Hellman pour configurer le cryptage sans fil. Avec OWE, le client et le point d'accès effectuent un échange de clés Diffie-Hellman au cours de la procédure d'accès et utilisent le secret PMK (Pairwise Master Key) résultant avec la connexion en 4 étapes.

    Comme l'illustre le schéma suivant, une authentification et une association ouvertes standard se produisent, puis le processus d'échange en quatre étapes génère les clés nécessaires au chiffrement.

    OWE frame exchangeéchange de trames OWE

    Vous pouvez trouver plus de détails dans le document Configure Enhanced Open SSID with Transition Mode - OWE .

    OWE est le successeur naturel d'un réseau ouvert dans WiFi 6E. Par conséquent, dans ce document, nous utilisons OWE comme sécurité de couche 2 pour la conformité WiFi6E.

    Points d'accès Cisco Catalyst Wi-Fi 6E

    Référence rapide aux points d'accès WiFi 6E disponibles au moment de la rédaction de ce document :

    Wi-Fi 6E Access PointsPoints d'accès Wi-Fi 6E

    Configuration et vérification

    Dans cette section, nous montrons comment configurer et vérifier la connexion des clients WiFi 6E à un WLAN à l'aide de l'authentification L3.

    Les paramètres de sécurité de couche 2 doivent être verrouillés sur Opportunistic Wireless Encryption (OWE) qui est le plus proche d'un réseau « ouvert » que nous pouvons avoir dans WiFi 6E. 

    Nous configurons et vérifions ces types d'authentification Web avec WiFi 6E :

    • Authentification Web locale
    • Authentification Web externe
    • Authentification Web centralisée

    Diagramme du réseau

    Voici le schéma de configuration des travaux pratiques utilisé dans ce document.

    Network DiagramDiagramme du réseau

    Configuration d'OWE avec authentification Web locale

    Étape 1. Créer une carte de paramètres pour l'authentification Web locale :

    LWA Parameter mapCarte des paramètres LWA

    Étape 2. Dans cet exemple, nous utilisons une base de données utilisateur externe pour l'authentification client. Le serveur AAA est ISE. Configurer le serveur RADIUS et le profil d'authentification :

    LWA AAA Authentication MethodMéthode d'authentification LWA AAA

    Étape 3. Configurez le WLAN avec la sécurité de couche 2 OWE et l'authentification Web comme sécurité de couche 3. Assurez-vous de sélectionner la carte de paramètre LocalWebAuth et la liste d'authentification LWA_Radius : 

    OWE with LWA Layer 3 configuration detailsDétails de la configuration OWE avec LWA de couche 3

    Le réseau local sans fil génère les paramètres de sécurité indiqués dans la partie droite :

    WLAN OWE with LWA L3 SecurityWLAN OWE avec sécurité LWA L3

    Étape 4. Mappez le WLAN à un profil de stratégie dans une balise de stratégie :

    LWA Policy Tag configurationConfiguration des balises de stratégie LWA

    Étape 5. Attribuez la balise de stratégie aux points d'accès.

    Étape 6. Configurez ISE en conséquence.

    note-icon

    Remarque : reportez-vous au document Configurer l'authentification Web locale avec l'authentification externe pour une configuration détaillée.

    Vérifier

    Il s'agit de la section de vérification de l'authentification Web locale.

    Vérifiez la configuration sur CLI :

    !
    aaa new-model
    !
    aaa group server radius ISE_RADIUS
     server name PSN01
     deadtime 5
     load-balance method least-outstanding
     subscriber mac-filtering security-mode mac
     mac-delimiter colon
    !
    aaa authentication login LWA_Radius group ISE_RADIUS
    !
    parameter-map type webauth global
     type webauth
     virtual-ip ipv4 192.0.2.1
     trustpoint eWLC-9800-01_WLC_TP
     webauth-http-enable
    !
    parameter-map type webauth LocalWebAuth
     type webauth
     timeout init-state sec 60
     max-http-conns 10
     custom-page login device bootflash:/custom_webauth/login.html
     custom-page success device bootflash:/custom_webauth/aup.html
     custom-page failure device bootflash:/custom_webauth/failed.html
     custom-page login expired device bootflash:/custom_webauth/logout.html
    !
    radius server PSN01
     address ipv4 192.168.1.7 auth-port 1812 acct-port 1813
     key 7 xxxxxxxxxxxx
    !
    wireless profile policy CentralSwPolicyProfile
    !
     ipv4 dhcp required
     vlan default
     no shutdown
    !
    wireless tag policy Wifi6E_TestPolicy
     wlan wifi6E_test policy CentralSwPolicyProfile
    !
    wlan wifi6E_test 5 wifi6E_test
     dot11ax target-waketime
     dot11ax twt-broadcast-support
     radio policy dot11 6ghz
     no security ft adaptive
     no security wpa wpa2
     no security wpa akm dot1x
     security wpa akm owe
     security wpa wpa3
     security dot1x authentication-list ISE_RADIUS
     security pmf mandatory
     security web-auth
     security web-auth authentication-list LWA_Radius
     security web-auth parameter-map LocalWebAuth
     no shutdown
    !

    Dans cet exemple, nous pouvons observer la phase OWE à l'aide du client AX211. Pour noter qu'il s'agit d'un EPC sur l'interface WLC :

    LWA OWE Associationassociation de droit néerlandais des créditeurs d'entreprises

    Suivi de la redirection DHCP, DNS et HTTP :

    LWA OWE RedirectionRedirection LWA OWE

    Sur l'interface graphique utilisateur du WLC, nous pouvons voir les détails du client :

    LWA OWE Client details on WLC GUIDétails du client LWA OWE sur l'interface graphique WLC

    Configuration d'OWE avec authentification Web externe

    Étape 1. Créer une carte de paramètres pour l'authentification Web externe :

    EWA Parameter mapCarte des paramètres EWA

    Étape 2. Dans cet exemple, nous utilisons une base de données utilisateur externe pour l'authentification client. Le serveur AAA est ISE. Configurer le serveur RADIUS et le profil d'authentification :

    AAA Authentication method configurationAAA Authentication, méthode de configuration

    Étape 3. Configurez le WLAN avec la sécurité de couche 2 OWE et l'authentification Web comme sécurité de couche 3. Assurez-vous que vous sélectionnez la carte ExternalWebAuth Parameter et la liste d'authentification EWA_Radius : 

    OWE EWA Security configurationConfiguration de sécurité OWE EWA

    Le réseau local sans fil génère les paramètres de sécurité indiqués dans la partie droite :

    OWE EWA Security settingsParamètres de sécurité OWE EWA

    Étape 4. Mappez le WLAN à un profil de stratégie dans une balise de stratégie :

    Policy Tag configurationConfiguration des balises des politiques

    Étape 5. Attribuez la balise de stratégie aux points d'accès.

    Étape 6. Configurez ISE en conséquence.

    note-icon

    Remarque : référez-vous au document Configurer et dépanner l'authentification Web externe sur le WLC 9800 pour une configuration détaillée.

    Vérifier

    Il s'agit de la section de vérification de l'authentification Web externe.

    Vérifiez la configuration sur CLI :

    !
    aaa new-model
    !
    aaa group server radius ISE_RADIUS
     server name PSN01
     deadtime 5
     load-balance method least-outstanding
     subscriber mac-filtering security-mode mac
     mac-delimiter colon
    !
    aaa authentication login EWA_Radius group ISE_RADIUS
    !
    parameter-map type webauth global
     type webauth
     virtual-ip ipv4 192.0.2.1
     trustpoint eWLC-9800-01_WLC_TP
     webauth-http-enable
    !
    parameter-map type webauth ExternalWebAuth
     type webauth
     timeout init-state sec 60
     redirect for-login https://192.168.1.17/EWAPortal/login.html
     redirect append ap-mac tag ap_mac
     redirect append client-mac tag client_mac
     redirect append wlan-ssid tag ssid
     redirect portal ipv4 192.168.1.17
     max-http-conns 10
    !
    radius server PSN01
     address ipv4 192.168.1.7 auth-port 1812 acct-port 1813
     key 7 xxxxxxxxxxxx
    !
    wireless profile policy CentralSwPolicyProfile
    !
     ipv4 dhcp required
     vlan default
     no shutdown
    !
    wireless tag policy Wifi6E_TestPolicy
     wlan wifi6E_EWA policy CentralSwPolicyProfile
    !
    wlan wifi6E_EWA 6 wifi6E_EWA
     radio policy dot11 6ghz
     no security ft adaptive
     no security wpa wpa2
     no security wpa akm dot1x
     security wpa akm owe
     security wpa wpa3
     security pmf mandatory
     security web-auth
     security web-auth authentication-list EWA_Radius
     security web-auth parameter-map ExternalWebAuth
     no shutdown
    !

    Ici, nous pouvons observer la phase OWE OTA en utilisant Samsung S23 comme exemple :

    OWE detail in EWA WLAN Association/AuthenticationDétails OWE dans Association/Authentification WLAN EWA

    Suivi de la redirection DHCP, DNS et HTTP. Veuillez noter que cette capture est la vue via EPC au niveau du WLC parce que OTA le trafic est chiffré :

    Packet capture detail on EWADétail de la capture de paquets sur EWA

    À ce stade, le client est en attente d'authentification Web :

    EWA client in Web Auth PendingClient EWA en attente d'authentification Web

    Client Security details of EWA Web Auth PendingDétails de sécurité client de l'authentification Web EWA en attente

    Authentification Radius des informations d'identification fournies du WLC à ISE :

    EWA Radius authenticationAuthentification EWA Radius

    Et les détails du client après une connexion réussie :

    OWE EWA Client detailsDétails du client OWE EWA

    Configuration d'OWE avec authentification Web centralisée

    Étape 1. Créer une ACL de redirection :

    CWA Redirect ACLACL de redirection CWA

    Étape 2. Créez la méthode Authorization à utiliser avec le filtrage mac :

    CWA AAA Authorization methodMéthode d'autorisation AAA CWA

    Étape 3. Configurez le WLAN avec la sécurité de couche 2 OWE et le filtrage mac. Sélectionnez la liste d'autorisations créée précédemment.

    OWE CWA Security configurationConfiguration de la sécurité OWE CWA

    Le réseau local sans fil génère les paramètres de sécurité indiqués dans la partie droite :

    OWE CWA Security settingsParamètres de sécurité OWE CWA

    Étape 4. Créez un profil de stratégie avec remplacement AAA et NAC Radius activé :

    CWA Policy ProfileProfil de politique CWA

    Étape 5. Mappez le WLAN à un profil de stratégie dans une balise de stratégie :

    CWA Policy TagBalise de stratégie CWA

    Étape 6. Attribuez la balise de stratégie aux points d'accès.

    Étape 7. Configurez ISE en conséquence.

    note-icon

    Remarque : reportez-vous au document Configure Central Web Authentication (CWA) on Catalyst 9800 WLC and ISE pour une configuration CWA détaillée.

    Vérifier

    Il s'agit de la section de vérification de l'authentification Web centrale.

    Vérifiez la configuration sur CLI :

    !
    aaa new-model
    !
    aaa group server radius ISE_RADIUS
     server name PSN01
     deadtime 5
     load-balance method least-outstanding
     subscriber mac-filtering security-mode mac
     mac-delimiter colon
    !
    aaa authorization network RadiusAuthor group ISE_RADIUS local
    !
    parameter-map type webauth global
     type webauth
     virtual-ip ipv4 192.0.2.1
     trustpoint eWLC-9800-01_WLC_TP
     webauth-http-enable
    !
    radius server PSN01
     address ipv4 192.168.1.7 auth-port 1812 acct-port 1813
     key 7 xxxxxxxxxxxx
    !
    wireless profile policy CentralSwPolicyProfile
    !
     ipv4 dhcp required
     vlan default
     no shutdown
    !
    wireless tag policy Wifi6E_TestPolicy
     wlan wifi6E_CWA policy CentralSwPolicyProfile
    !
    wlan wifi6E_CWA 7 wifi6E_CWA
     mac-filtering RadiusAuthor
     radio policy dot11 6ghz
     no security ft adaptive
     no security wpa wpa2
     no security wpa akm dot1x
     security wpa akm owe
     security wpa wpa3
     security pmf mandatory
     no shutdown
    !

    Ici, nous pouvons observer la phase OWE OTA en utilisant le pixel 6a comme exemple :

    CWA OWE OTA connectionConnexion OTA CWA OWE

    Ensuite, nous avons le Radius Exchange pour le filtrage MAC :

    OEW CWA Mac filteringFiltrage Mac OEW CWA

    Suivi de la redirection DHCP, DNS et HTTP :

    CWA DHCP, DNS and RedirectionDHCP, DNS et redirection CWA

    Sur les journaux ISE Live, nous pouvons voir la redirection CWA :

    CWA Redirection URL and ACLURL et ACL de redirection CWA

    Les journaux ISE Live indiquent que le client a saisi les informations d'identification d'invité et a réussi l'authentification :

    CWA guest login successfulConnexion de l'invité CWA réussie

    Et les détails du client après une connexion réussie :

    OWE CWA Client details on WLC GUIDétails du client OWE CWA sur l'interface graphique WLC

    Dépannage

    Le dépannage utilisé dans ce document est basé sur le document en ligne :

    Dépannage des AP COS

    La ligne directrice générale pour le dépannage est de collecter la trace RA en mode de débogage à partir du WLC en utilisant l'adresse mac du client en s'assurant que le client se connecte en utilisant l'adresse mac du périphérique et non une adresse mac randomisée.

    Pour le dépannage Over the Air, la recommandation est d'utiliser AP en mode sniffer capturant le trafic sur le canal du client desservant AP.

    note-icon

    Remarque : reportez-vous à la section Informations importantes sur les commandes de débogage avant d'utiliser les commandes de débogage.

    DETTE à l'égard du droit

    Ici, nous pouvons voir un exemple de LWA dans les traces RA :

    2023/08/08 13:37:58.196529135 {wncd_x_R0-0}{1}: [client-orch-sm] [15154]: (note): MAC: 286b.3598.580f Association received. BSSID 00df.1ddd.7d38, WLAN wifi6E_test, Slot 3 AP 00df.1ddd.7d30, AP9136_5C.F524
    [...]
    2023/08/08 13:37:58.198092314 {wncd_x_R0-0}{1}: [dot11] [15154]: (note): MAC: 286b.3598.580f Association success. AID 36, Roaming = False, WGB = False, 11r = False, 11w = True Fast roam = False
    [...]
    2023/08/08 13:37:58.198287303 {wncd_x_R0-0}{1}: [client-orch-sm] [15154]: (debug): MAC: 286b.3598.580f Starting L2 authentication. Bssid in state machine:00df.1ddd.7d38 Bssid in request is:00df.1ddd.7d38
    2023/08/08 13:37:58.198308994 {wncd_x_R0-0}{1}: [client-orch-state] [15154]: (note): MAC: 286b.3598.580f Client state transition: S_CO_ASSOCIATING -> S_CO_L2_AUTH_IN_PROGRESS
    [...]
    2023/08/08 13:37:58.200859342 {wncd_x_R0-0}{1}: [ewlc-infra-evq] [15154]: (note): Authentication Success. Resolved Policy bitmap:11 for client 286b.3598.580f 
    [...]
    2023/08/08 13:37:58.222523865 {wncd_x_R0-0}{1}: [client-auth] [15154]: (info): MAC: 286b.3598.580f Client auth-interface state transition: S_AUTHIF_ADD_MOBILE_ACK_WAIT_KM -> S_AUTHIF_PSK_AUTH_KEY_XCHNG_PENDING
    2023/08/08 13:37:58.222547149 {mobilityd_R0-0}{1}: [mm-client] [16404]: (debug): MAC: 0000.0000.0000 Received pmk_update, sub type: 0 of XID (0) from (WNCD[0])
    2023/08/08 13:37:58.222630557 {mobilityd_R0-0}{1}: [mm-dgram-io] [16404]: (debug): MAC: 0000.0000.0000 Sending message: pmk_update to group: holyfountain
    2023/08/08 13:37:58.222641428 {mobilityd_R0-0}{1}: [mm-dgram-io] [16404]: (debug): MAC: 0000.0000.0000 Failed to send message: pmk_update, total configured peers: 2, no active peers
    2023/08/08 13:37:58.222666535 {wncd_x_R0-0}{1}: [client-keymgmt] [15154]: (info): MAC: 286b.3598.580f EAP key M1 Sent successfully
    2023/08/08 13:37:58.222678418 {wncd_x_R0-0}{1}: [client-keymgmt] [15154]: (info): MAC: 286b.3598.580f Client key-mgmt state transition: S_INITPMK -> S_PTK_START
    2023/08/08 13:37:58.227626495 {wncd_x_R0-0}{1}: [client-keymgmt] [15154]: (info): MAC: 286b.3598.580f M2 Status: EAP key M2 validation success
    2023/08/08 13:37:58.227791247 {wncd_x_R0-0}{1}: [client-keymgmt] [15154]: (info): MAC: 286b.3598.580f EAP key M3 Sent successfully
    2023/08/08 13:37:58.227792680 {wncd_x_R0-0}{1}: [client-keymgmt] [15154]: (info): MAC: 286b.3598.580f Client key-mgmt state transition: S_PTK_START -> S_PTKINITNEGOTIATING
    2023/08/08 13:37:58.230572903 {wncd_x_R0-0}{1}: [client-keymgmt] [15154]: (info): MAC: 286b.3598.580f M4 Status: EAP key M4 validation is successful
    2023/08/08 13:37:58.230575999 {wncd_x_R0-0}{1}: [client-keymgmt] [15154]: (note): MAC: 286b.3598.580f EAP Key management successful. AKM:OWE Cipher:CCMP WPA Version: WPA3
    2023/08/08 13:37:58.230603571 {wncd_x_R0-0}{1}: [client-keymgmt] [15154]: (info): MAC: 286b.3598.580f Client key-mgmt state transition: S_PTKINITNEGOTIATING -> S_PTKINITDONE
    2023/08/08 13:37:58.230702678 {wncd_x_R0-0}{1}: [client-auth] [15154]: (note): MAC: 286b.3598.580f L2 Authentication initiated. method WEBAUTH, Policy VLAN 0, AAA override = 1
    2023/08/08 13:37:58.230791777 {wncd_x_R0-0}{1}: [auth-mgr] [15154]: (info): [286b.3598.580f:capwap_9000000b] Session Start event called from SANET-SHIM, vlan: 0
    2023/08/08 13:37:58.230807848 {wncd_x_R0-0}{1}: [auth-mgr] [15154]: (info): [286b.3598.580f:capwap_9000000b] Wireless session sequence, create context with method WebAuth
    2023/08/08 13:37:58.230831713 {wncd_x_R0-0}{1}: [auth-mgr-feat_wireless] [15154]: (info): [286b.3598.580f:capwap_9000000b] - authc_list: LWA_Radius
    2023/08/08 13:37:58.230834488 {wncd_x_R0-0}{1}: [auth-mgr-feat_wireless] [15154]: (info): [286b.3598.580f:capwap_9000000b] - authz_list: Not present under wlan configuration
    2023/08/08 13:37:58.230857151 {wncd_x_R0-0}{1}: [client-auth] [15154]: (info): MAC: 286b.3598.580f Client auth-interface state transition: S_AUTHIF_PSK_AUTH_KEY_XCHNG_PENDING -> S_AUTHIF_L2_WEBAUTH_PENDING
    2023/08/08 13:37:58.230912145 {wncd_x_R0-0}{1}: [auth-mgr] [15154]: (info): [286b.3598.580f:capwap_9000000b] Raised event RX_IDENTITY_UPDATE (18)
    2023/08/08 13:37:58.230915511 {wncd_x_R0-0}{1}: [auth-mgr] [15154]: (info): [286b.3598.580f:capwap_9000000b] SESSION_START from WCM (exp 1476396949, got 1476396949) overriding with latest
    2023/08/08 13:37:58.230971648 {wncd_x_R0-0}{1}: [auth-mgr] [15154]: (info): [286b.3598.580f:capwap_9000000b] Retrieved Client IIF ID 0x1476396949x in clientrx event
    2023/08/08 13:37:58.230998298 {wncd_x_R0-0}{1}: [auth-mgr] [15154]: (info): [286b.3598.580f:capwap_9000000b] DC Profile-name has been changed to LENOVO 21CCS43W0T 
    2023/08/08 13:37:58.231001354 {wncd_x_R0-0}{1}: [auth-mgr] [15154]: (info): [286b.3598.580f:capwap_9000000b] DC Device-name has been changed to CSCO-W-PF445DKE 
    2023/08/08 13:37:58.231043724 {wncd_x_R0-0}{1}: [auth-mgr] [15154]: (info): [286b.3598.580f:capwap_9000000b] Session start (restart) for 286b.3598.580f
    [...]
    2023/08/08 13:37:58.231245206 {wncd_x_R0-0}{1}: [webauth-state] [15154]: (info): capwap_9000000b[286b.3598.580f][ 0.0.0.0]Param-map used: LocalWebAuth
    2023/08/08 13:37:58.231251037 {wncd_x_R0-0}{1}: [webauth-state] [15154]: (info): capwap_9000000b[286b.3598.580f][ 0.0.0.0]State INIT -> INIT
    2023/08/08 13:37:58.231273499 {wncd_x_R0-0}{1}: [webauth-acl] [15154]: (info): capwap_9000000b[286b.3598.580f][ 0.0.0.0]Applying IPv4 intercept ACL via SVM, name: IP-Adm-V4-Int-ACL-global, priority: 50, IIF-ID: 0
    [...]
    2023/08/08 13:37:58.239843453 {wncd_x_R0-0}{1}: [client-iplearn] [15154]: (info): MAC: 286b.3598.580f IP-learn state transition: S_IPLEARN_INIT -> S_IPLEARN_IN_PROGRESS
    2023/08/08 13:37:58.239903667 {wncd_x_R0-0}{1}: [client-iplearn] [15154]: (note): MAC: 286b.3598.580f Client IP learn successful. Method: DHCP IP: 192.168.1.159
    [...]
    2023/08/08 13:37:58.240371152 {wncd_x_R0-0}{1}: [auth-mgr-feat_acct] [15154]: (info): [286b.3598.580f:capwap_9000000b] SM Notified attribute Add/Update addr 192.168.1.159
    2023/08/08 13:37:58.240390128 {wncd_x_R0-0}{1}: [client-iplearn] [15154]: (info): MAC: 286b.3598.580f IP-learn state transition: S_IPLEARN_IN_PROGRESS -> S_IPLEARN_COMPLETE
    2023/08/08 13:37:58.240437257 {wncd_x_R0-0}{1}: [client-orch-sm] [15154]: (debug): MAC: 286b.3598.580f Received ip learn response. method: IPLEARN_METHOD_DHCP
    2023/08/08 13:37:58.240457105 {wncd_x_R0-0}{1}: [client-orch-sm] [15154]: (debug): MAC: 286b.3598.580f Triggered L3 authentication. status = 0x0, Success
    2023/08/08 13:37:58.240459018 {wncd_x_R0-0}{1}: [client-orch-state] [15154]: (note): MAC: 286b.3598.580f Client state transition: S_CO_IP_LEARN_IN_PROGRESS -> S_CO_L3_AUTH_IN_PROGRESS
    2023/08/08 13:37:58.240527728 {wncd_x_R0-0}{1}: [dot1x] [15154]: (info): [0000.0000.0000:capwap_9000000b] Couldn't find the supplicant in the list
    2023/08/08 13:37:58.240760238 {wncd_x_R0-0}{1}: [client-auth] [15154]: (note): MAC: 286b.3598.580f L3 Authentication initiated. LWA 
    2023/08/08 13:37:58.240767232 {wncd_x_R0-0}{1}: [client-auth] [15154]: (info): MAC: 286b.3598.580f Client auth-interface state transition: S_AUTHIF_L2_WEBAUTH_DONE -> S_AUTHIF_WEBAUTH_PENDING
    [...]
    2023/08/08 13:37:58.924439975 {wncd_x_R0-0}{1}: [webauth-io] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]60437/5 IO state NEW -> READING
    2023/08/08 13:37:58.924590710 {wncd_x_R0-0}{1}: [webauth-io] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]60437/5 Read event, Message ready
    2023/08/08 13:37:58.924606621 {wncd_x_R0-0}{1}: [webauth-httpd] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]GET rcvd when in INIT state
    2023/08/08 13:37:58.924617631 {wncd_x_R0-0}{1}: [webauth-httpd] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]HTTP GET request
    2023/08/08 13:37:58.924646336 {wncd_x_R0-0}{1}: [webauth-httpd] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]Parse GET, src [192.168.1.159] dst [x.x.x.x] url [http://www.msftconnecttest.com/connecttest.txt]
    2023/08/08 13:37:58.924811559 {wncd_x_R0-0}{1}: [webauth-httpd] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]Read complete: parse_request return 8
    2023/08/08 13:37:58.924823291 {wncd_x_R0-0}{1}: [webauth-state] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]Param-map used: LocalWebAuth
    2023/08/08 13:37:58.924830184 {wncd_x_R0-0}{1}: [webauth-state] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]State INIT -> GET_REDIRECT
    2023/08/08 13:37:58.924836706 {wncd_x_R0-0}{1}: [webauth-io] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]60437/5 IO state READING -> WRITING
    2023/08/08 13:37:58.924893704 {wncd_x_R0-0}{1}: [webauth-io] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]60437/5 IO state WRITING -> END
    [...]
    2023/08/08 13:38:16.814516928 {wncd_x_R0-0}{1}: [webauth-io] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]60515/217 IO state NEW -> SSL_HANDSHAKING
    2023/08/08 13:38:16.814739389 {wncd_x_R0-0}{1}: [webauth-io] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]60516/218 IO state NEW -> SSL_HANDSHAKING
    2023/08/08 13:38:16.843721875 {wncd_x_R0-0}{1}: [webauth-io] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]60517/217 IO state NEW -> SSL_HANDSHAKING
    2023/08/08 13:38:16.863779947 {wncd_x_R0-0}{1}: [webauth-io] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]60517/217 Read event, Message ready
    2023/08/08 13:38:16.863799384 {wncd_x_R0-0}{1}: [webauth-httpd] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]POST rcvd when in LOGIN state
    2023/08/08 13:38:16.863812318 {wncd_x_R0-0}{1}: [webauth-httpd] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]get url: /undefined
    2023/08/08 13:38:16.863857023 {wncd_x_R0-0}{1}: [webauth-httpd] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]Read complete: parse_request return 4
    2023/08/08 13:38:16.863981829 {wncd_x_R0-0}{1}: [caaa-authen] [15154]: (info): [CAAA:AUTHEN:c8000018] NULL ATTR LIST 
    2023/08/08 13:38:16.864023268 {wncd_x_R0-0}{1}: [webauth-state] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]Param-map used: LocalWebAuth
    2023/08/08 13:38:16.864026684 {wncd_x_R0-0}{1}: [webauth-state] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]State LOGIN -> AUTHENTICATING
    2023/08/08 13:38:16.864039067 {wncd_x_R0-0}{1}: [webauth-io] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]60517/217 IO state READING -> AUTHENTICATING
    2023/08/08 13:38:16.864184873 {wncd_x_R0-0}{1}: [radius] [15154]: (info): RADIUS: Send Access-Request to 192.168.1.7:1812 id 0/5, len 390
    2023/08/08 13:38:16.864190705 {wncd_x_R0-0}{1}: [radius] [15154]: (info): RADIUS: authenticator 50 a9 ab 0d 42 ef 39 22 - 33 3d 07 b0 77 78 80 88
    2023/08/08 13:38:16.864194552 {wncd_x_R0-0}{1}: [radius] [15154]: (info): RADIUS: Calling-Station-Id [31] 19 "28-6b-35-98-58-0f"
    2023/08/08 13:38:16.864197568 {wncd_x_R0-0}{1}: [radius] [15154]: (info): RADIUS: User-Name [1] 7 "tiago"
    [...]
    2023/08/08 13:38:16.879241798 {wncd_x_R0-0}{1}: [radius] [15154]: (info): RADIUS: Received from id 1812/5 192.168.1.7:0, Access-Accept, len 128
    [...]
    2023/08/08 13:38:16.879504014 {wncd_x_R0-0}{1}: [webauth-state] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]Param-map used: LocalWebAuth
    2023/08/08 13:38:16.879513532 {wncd_x_R0-0}{1}: [webauth-state] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]State AUTHENTICATING -> AUTHC_SUCCESS
    2023/08/08 13:38:16.879530745 {wncd_x_R0-0}{1}: [webauth-acl] [15154]: (info): capwap_9000000b[286b.3598.580f][ 192.168.1.159]Unapply IPv4 intecept ACL via SVM, name "IP-Adm-V4-Int-ACL-global", pri 50, IIF 0 
    [...]
    2023/08/08 13:38:16.880956564 {wncd_x_R0-0}{1}: [ewlc-infra-evq] [15154]: (note): Authentication Success. Resolved Policy bitmap:4 for client 286b.3598.580f 
    [...]
    2023/08/08 13:38:16.882320225 {wncd_x_R0-0}{1}: [errmsg] [15154]: (info): %CLIENT_ORCH_LOG-6-CLIENT_ADDED_TO_RUN_STATE: R0/0: wncd: Username entry (tiago) joined with ssid (wifi6E_test) for device with MAC: 286b.3598.580f
    [...]
    2023/08/08 13:38:16.882451875 {wncd_x_R0-0}{1}: [rog-proxy-capwap] [15154]: (debug): Managed client RUN state notification: 286b.3598.580f
    2023/08/08 13:38:16.882495928 {wncd_x_R0-0}{1}: [client-orch-state] [15154]: (note): MAC: 286b.3598.580f Client state transition: S_CO_L3_AUTH_IN_PROGRESS -> S_CO_RUN
    [...]

    Référez-vous au document Configurer l'authentification Web locale avec l'authentification externe pour les étapes de dépannage détaillées.

    DETTE avec EWA

    Ici, nous pouvons voir un exemple d'EWA dans les traces RA :

    2023/08/10 14:35:20.685078384 {wncd_x_R0-0}{1}: [client-orch-sm] [15195]: (note): MAC: 0429.2ec9.e371 Association received. BSSID 00df.1ddd.7d39, WLAN wifi6E_EWA, Slot 3 AP 00df.1ddd.7d30, AP9136_5C.F524
    2023/08/10 14:35:20.685117718 {wncd_x_R0-0}{1}: [client-orch-sm] [15195]: (debug): MAC: 0429.2ec9.e371 Received Dot11 association request. Processing started,SSID: wifi6E_EWA, Policy profile: CentralSwPolicyProfile, AP Name: AP9136_5C.F524, Ap Mac Address: 00df.1ddd.7d30BSSID MAC0000.0000.0000wlan ID: 6RSSI: -57, SNR: 41
    2023/08/10 14:35:20.685226454 {wncd_x_R0-0}{1}: [client-orch-state] [15195]: (note): MAC: 0429.2ec9.e371 Client state transition: S_CO_INIT -> S_CO_ASSOCIATING
    2023/08/10 14:35:20.685420591 {wncd_x_R0-0}{1}: [dot11-validate] [15195]: (info): MAC: 0429.2ec9.e371 Dot11 ie validate ext/supp rates. Validation Passed for Supported rates radio_type 16
    2023/08/10 14:35:20.685422154 {wncd_x_R0-0}{1}: [dot11-validate] [15195]: (info): MAC: 0429.2ec9.e371 WiFi direct: Dot11 validate P2P IE. P2P IE not present.
    2023/08/10 14:35:20.685864592 {wncd_x_R0-0}{1}: [dot11] [15195]: (debug): MAC: 0429.2ec9.e371 dot11 send association response. Framing association response with resp_status_code: 0
    2023/08/10 14:35:20.685865002 {wncd_x_R0-0}{1}: [dot11] [15195]: (info): MAC: 0429.2ec9.e371 Dot11 capability privacy bit set TRUE
    2023/08/10 14:35:20.685867818 {wncd_x_R0-0}{1}: [dot11] [15195]: (debug): MAC: 0429.2ec9.e371 Dot11 Capability info byte1 11, byte2: 10
    2023/08/10 14:35:20.685886032 {wncd_x_R0-0}{1}: [dot11-frame] [15195]: (info): MAC: 0429.2ec9.e371 WiFi direct: skip build Assoc Resp with P2P IE: Wifi direct policy disabled
    2023/08/10 14:35:20.685991953 {wncd_x_R0-0}{1}: [dot11] [15195]: (info): MAC: 0429.2ec9.e371 dot11 send association response. Sending assoc response of length: 183 with resp_status_code: 0, DOT11_STATUS: DOT11_STATUS_SUCCESS
    2023/08/10 14:35:20.685995339 {wncd_x_R0-0}{1}: [dot11] [15195]: (note): MAC: 0429.2ec9.e371 Association success. AID 33, Roaming = False, WGB = False, 11r = False, 11w = True Fast roam = False
    2023/08/10 14:35:20.686003685 {wncd_x_R0-0}{1}: [dot11] [15195]: (info): MAC: 0429.2ec9.e371 DOT11 state transition: S_DOT11_INIT -> S_DOT11_ASSOCIATED
    2023/08/10 14:35:20.686061695 {wncd_x_R0-0}{1}: [client-orch-sm] [15195]: (debug): MAC: 0429.2ec9.e371 Station Dot11 association is successful. 
    2023/08/10 14:35:20.686088796 {wncd_x_R0-0}{1}: [client-orch-sm] [15195]: (debug): MAC: 0429.2ec9.e371 Starting L2 authentication. Bssid in state machine:00df.1ddd.7d39 Bssid in request is:00df.1ddd.7d39
    2023/08/10 14:35:20.686099576 {wncd_x_R0-0}{1}: [client-orch-state] [15195]: (note): MAC: 0429.2ec9.e371 Client state transition: S_CO_ASSOCIATING -> S_CO_L2_AUTH_IN_PROGRESS
    2023/08/10 14:35:20.686125926 {wncd_x_R0-0}{1}: [client-auth] [15195]: (note): MAC: 0429.2ec9.e371 L2 Authentication initiated. method PSK, Policy VLAN 0, AAA override = 1, NAC = 0
    [...]
    2023/08/10 14:35:20.687526737 {wncd_x_R0-0}{1}: [auth-mgr] [15195]: (info): [0429.2ec9.e371:capwap_90000010] Raised event AUTHZ_SUCCESS (11)
    2023/08/10 14:35:20.687530575 {wncd_x_R0-0}{1}: [auth-mgr] [15195]: (info): [0429.2ec9.e371:capwap_90000010] Context changing state from 'Idle' to 'Authz Success'
    2023/08/10 14:35:20.687533620 {wncd_x_R0-0}{1}: [auth-mgr] [15195]: (info): [0429.2ec9.e371:capwap_90000010] Authorized open auth session for 0429.2ec9.e371
    [...]
    2023/08/10 14:35:20.687804543 {wncd_x_R0-0}{1}: [client-auth] [15195]: (info): MAC: 0429.2ec9.e371 Client auth-interface state transition: S_AUTHIF_AWAIT_PSK_AUTH_START_RESP -> S_AUTHIF_PSK_AUTH_PENDING
    2023/08/10 14:35:20.687807038 {wncd_x_R0-0}{1}: [ewlc-infra-evq] [15195]: (note): Authentication Success. Resolved Policy bitmap:11 for client 0429.2ec9.e371 
    [...]
    2023/08/10 14:35:20.691676380 {wncd_x_R0-0}{1}: [client-auth] [15195]: (info): MAC: 0429.2ec9.e371 Client auth-interface state transition: S_AUTHIF_ADD_MOBILE_ACK_WAIT_KM -> S_AUTHIF_PSK_AUTH_KEY_XCHNG_PENDING
    2023/08/10 14:35:20.691841904 {wncd_x_R0-0}{1}: [client-keymgmt] [15195]: (info): MAC: 0429.2ec9.e371 EAP key M1 Sent successfully
    2023/08/10 14:35:20.691844278 {wncd_x_R0-0}{1}: [client-keymgmt] [15195]: (info): MAC: 0429.2ec9.e371 Client key-mgmt state transition: S_INITPMK -> S_PTK_START
    2023/08/10 14:35:20.721636921 {wncd_x_R0-0}{1}: [client-keymgmt] [15195]: (info): MAC: 0429.2ec9.e371 M2 Status: EAP key M2 validation success
    2023/08/10 14:35:20.721730809 {wncd_x_R0-0}{1}: [client-keymgmt] [15195]: (info): MAC: 0429.2ec9.e371 EAP key M3 Sent successfully
    2023/08/10 14:35:20.721736890 {wncd_x_R0-0}{1}: [client-keymgmt] [15195]: (info): MAC: 0429.2ec9.e371 Client key-mgmt state transition: S_PTK_START -> S_PTKINITNEGOTIATING
    2023/08/10 14:35:20.739641625 {wncd_x_R0-0}{1}: [client-keymgmt] [15195]: (info): MAC: 0429.2ec9.e371 M4 Status: EAP key M4 validation is successful
    2023/08/10 14:35:20.739644982 {wncd_x_R0-0}{1}: [client-keymgmt] [15195]: (note): MAC: 0429.2ec9.e371 EAP Key management successful. AKM:OWE Cipher:CCMP WPA Version: WPA3
    2023/08/10 14:35:20.739650121 {wncd_x_R0-0}{1}: [client-keymgmt] [15195]: (info): MAC: 0429.2ec9.e371 Client key-mgmt state transition: S_PTKINITNEGOTIATING -> S_PTKINITDONE
    2023/08/10 14:35:20.739744971 {wncd_x_R0-0}{1}: [client-auth] [15195]: (note): MAC: 0429.2ec9.e371 L2 Authentication initiated. method WEBAUTH, Policy VLAN 0, AAA override = 1
    2023/08/10 14:35:20.739838779 {wncd_x_R0-0}{1}: [auth-mgr] [15195]: (info): [0429.2ec9.e371:capwap_90000010] Session Start event called from SANET-SHIM, vlan: 0
    2023/08/10 14:35:20.739847004 {wncd_x_R0-0}{1}: [auth-mgr] [15195]: (info): [0429.2ec9.e371:capwap_90000010] Wireless session sequence, create context with method WebAuth
    2023/08/10 14:35:20.739861071 {wncd_x_R0-0}{1}: [auth-mgr-feat_wireless] [15195]: (info): [0429.2ec9.e371:capwap_90000010] - authc_list: EWA_Radius
    [...]
    2023/08/10 14:35:20.740069114 {wncd_x_R0-0}{1}: [webauth-state] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 0.0.0.0]Param-map used: ExternalWebAuth
    2023/08/10 14:35:20.740071629 {wncd_x_R0-0}{1}: [webauth-state] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 0.0.0.0]State INIT -> INIT
    2023/08/10 14:35:20.740083452 {wncd_x_R0-0}{1}: [webauth-sm] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 0.0.0.0]Initiate session, forward state to 0 IF 0x90000010 mac [0429.2ec9.e371]
    2023/08/10 14:35:20.740085425 {wncd_x_R0-0}{1}: [webauth-sm] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 0.0.0.0]Initiate session, SM init sessions 1
    2023/08/10 14:35:20.740091236 {wncd_x_R0-0}{1}: [webauth-state] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 0.0.0.0]Param-map used: ExternalWebAuth
    2023/08/10 14:35:20.740093601 {wncd_x_R0-0}{1}: [webauth-state] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 0.0.0.0]State INIT -> INIT
    2023/08/10 14:35:20.740103810 {wncd_x_R0-0}{1}: [webauth-acl] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 0.0.0.0]Applying IPv4 intercept ACL via SVM, name: WA-v4-int-192.168.1.17, priority: 50, IIF-ID: 0
    [...]
    2023/08/10 14:35:21.942607594 {wncd_x_R0-0}{1}: [client-iplearn] [15195]: (note): MAC: 0429.2ec9.e371 Client IP learn successful. Method: DHCP IP: 192.168.1.160
    [...]
    2023/08/10 14:35:21.943838504 {wncd_x_R0-0}{1}: [client-iplearn] [15195]: (info): MAC: 0429.2ec9.e371 IP-learn state transition: S_IPLEARN_IN_PROGRESS -> S_IPLEARN_COMPLETE
    2023/08/10 14:35:21.944028273 {wncd_x_R0-0}{1}: [client-orch-sm] [15195]: (debug): MAC: 0429.2ec9.e371 Received ip learn response. method: IPLEARN_METHOD_DHCP
    2023/08/10 14:35:21.944069521 {wncd_x_R0-0}{1}: [client-orch-sm] [15195]: (debug): MAC: 0429.2ec9.e371 Triggered L3 authentication. status = 0x0, Success
    2023/08/10 14:35:21.944074851 {wncd_x_R0-0}{1}: [client-orch-state] [15195]: (note): MAC: 0429.2ec9.e371 Client state transition: S_CO_IP_LEARN_IN_PROGRESS -> S_CO_L3_AUTH_IN_PROGRESS
    2023/08/10 14:35:21.944201671 {wncd_x_R0-0}{1}: [dot1x] [15195]: (info): [0000.0000.0000:capwap_90000010] Couldn't find the supplicant in the list
    2023/08/10 14:35:21.944759066 {wncd_x_R0-0}{1}: [client-auth] [15195]: (note): MAC: 0429.2ec9.e371 L3 Authentication initiated. LWA 
    2023/08/10 14:35:21.944776669 {wncd_x_R0-0}{1}: [client-auth] [15195]: (info): MAC: 0429.2ec9.e371 Client auth-interface state transition: S_AUTHIF_L2_WEBAUTH_DONE -> S_AUTHIF_WEBAUTH_PENDING
    [...]
    2023/08/10 14:35:24.110614486 {wncd_x_R0-0}{1}: [webauth-io] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 192.168.1.160][2001:8a0:fb91:1c00:96e8:ab91:47c8:3d6e]capwap_90000010 60486/213 IO state NEW -> READING
    2023/08/10 14:35:24.110679789 {wncd_x_R0-0}{1}: [webauth-io] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 192.168.1.160][2001:8a0:fb91:1c00:96e8:ab91:47c8:3d6e]capwap_90000010 60486/213 Read event, Message ready
    2023/08/10 14:35:24.110699827 {wncd_x_R0-0}{1}: [webauth-httpd] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 192.168.1.160][2001:8a0:fb91:1c00:96e8:ab91:47c8:3d6e]capwap_90000010 GET rcvd when in LOGIN state
    2023/08/10 14:35:24.110718893 {wncd_x_R0-0}{1}: [webauth-httpd] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 192.168.1.160][2001:8a0:fb91:1c00:96e8:ab91:47c8:3d6e]capwap_90000010 HTTP GET request
    2023/08/10 14:35:24.110754721 {wncd_x_R0-0}{1}: [webauth-httpd] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 192.168.1.160][2001:8a0:fb91:1c00:96e8:ab91:47c8:3d6e]capwap_90000010 Parse GET, src [2001:8a0:fb91:1c00:96e8:ab91:47c8:3d6e] dst [2a00:1450:4003:811::2003] url [http://connectivitycheck.gstatic.com/generate_204]
    2023/08/10 14:35:24.110951163 {wncd_x_R0-0}{1}: [webauth-httpd] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 192.168.1.160][2001:8a0:fb91:1c00:96e8:ab91:47c8:3d6e]capwap_90000010 Read complete: parse_request return 10
    2023/08/10 14:35:24.110960801 {wncd_x_R0-0}{1}: [webauth-state] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 192.168.1.160][2001:8a0:fb91:1c00:96e8:ab91:47c8:3d6e]capwap_90000010 Param-map used: ExternalWebAuth
    2023/08/10 14:35:24.110971331 {wncd_x_R0-0}{1}: [webauth-state] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 192.168.1.160][2001:8a0:fb91:1c00:96e8:ab91:47c8:3d6e]capwap_90000010 State LOGIN -> LOGIN
    2023/08/10 14:35:24.111046654 {wncd_x_R0-0}{1}: [webauth-page] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 192.168.1.160][2001:8a0:fb91:1c00:96e8:ab91:47c8:3d6e]capwap_90000010 Sending Webauth login form, len 8077
    [...]
    2023/08/10 14:35:35.761960632 {wncd_x_R0-0}{1}: [webauth-io] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 192.168.1.160][2001:8a0:fb91:1c00:d20a:fcc:5919:3f1a]capwap_90000010 47440/213 IO state NEW -> SSL_HANDSHAKING
    2023/08/10 14:35:35.776669018 {wncd_x_R0-0}{1}: [webauth-io] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 192.168.1.160][2001:8a0:fb91:1c00:d20a:fcc:5919:3f1a]capwap_90000010 47450/213 IO state NEW -> SSL_HANDSHAKING
    2023/08/10 14:35:37.805884475 {wncd_x_R0-0}{1}: [webauth-io] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 192.168.1.160][2001:8a0:fb91:1c00:d20a:fcc:5919:3f1a]capwap_90000010 55760/213 IO state NEW -> READING
    2023/08/10 14:35:37.807261842 {wncd_x_R0-0}{1}: [webauth-io] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 192.168.1.160][2001:8a0:fb91:1c00:d20a:fcc:5919:3f1a]capwap_90000010 55760/213 Read event, Message ready
    2023/08/10 14:35:37.807273253 {wncd_x_R0-0}{1}: [webauth-httpd] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 192.168.1.160][2001:8a0:fb91:1c00:d20a:fcc:5919:3f1a]capwap_90000010 POST rcvd when in LOGIN state
    2023/08/10 14:35:37.807287911 {wncd_x_R0-0}{1}: [webauth-httpd] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 192.168.1.160][2001:8a0:fb91:1c00:d20a:fcc:5919:3f1a]capwap_90000010 get url: /login.html
    2023/08/10 14:35:37.807331213 {wncd_x_R0-0}{1}: [webauth-httpd] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 192.168.1.160][2001:8a0:fb91:1c00:d20a:fcc:5919:3f1a]capwap_90000010 Read complete: parse_request return 4
    [...]
    2023/08/10 14:35:37.807498470 {wncd_x_R0-0}{1}: [webauth-state] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 192.168.1.160][2001:8a0:fb91:1c00:d20a:fcc:5919:3f1a]capwap_90000010 Param-map used: ExternalWebAuth
    2023/08/10 14:35:37.807503619 {wncd_x_R0-0}{1}: [webauth-state] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 192.168.1.160][2001:8a0:fb91:1c00:d20a:fcc:5919:3f1a]capwap_90000010 State LOGIN -> AUTHENTICATING
    2023/08/10 14:35:37.807515502 {wncd_x_R0-0}{1}: [webauth-io] [15195]: (info): capwap_90000010[0429.2ec9.e371][ 192.168.1.160][2001:8a0:fb91:1c00:d20a:fcc:5919:3f1a]capwap_90000010 55760/213 IO state READING -> AUTHENTICATING
    2023/08/10 14:35:37.807653884 {wncd_x_R0-0}{1}: [radius] [15195]: (info): RADIUS: Send Access-Request to 192.168.1.7:1812 id 0/1, len 531
    2023/08/10 14:35:37.807663221 {wncd_x_R0-0}{1}: [radius] [15195]: (info): RADIUS: authenticator 56 a6 f6 4e 84 f8 00 e9 - 06 14 c9 b3 8d 77 2b 4c
    2023/08/10 14:35:37.807667159 {wncd_x_R0-0}{1}: [radius] [15195]: (info): RADIUS: Calling-Station-Id [31] 19 "04-29-2e-c9-e3-71"
    2023/08/10 14:35:37.807670215 {wncd_x_R0-0}{1}: [radius] [15195]: (info): RADIUS: User-Name [1] 7 "tiago"
    2023/08/10 14:35:37.807673040 {wncd_x_R0-0}{1}: [radius] [15195]: (info): RADIUS: Vendor, Cisco [26] 49
    2023/08/10 14:35:37.807676226 {wncd_x_R0-0}{1}: [radius] [15195]: (info): RADIUS: Cisco AVpair [1] 43 "audit-session-id=0F01A8C00000000DDFDF94C0"
    2023/08/10 14:35:37.807680083 {wncd_x_R0-0}{1}: [radius] [15195]: (info): RADIUS: Framed-IP-Address [8] 6 192.168.1.160 
    2023/08/10 14:35:37.807682217 {wncd_x_R0-0}{1}: [radius] [15195]: (info): RADIUS: Message-Authenticator[80] 18 ...
    2023/08/10 14:35:37.807701825 {wncd_x_R0-0}{1}: [radius] [15195]: (info): RADIUS: Service-Type [6] 6 Outbound [5]
    2023/08/10 14:35:37.807703838 {wncd_x_R0-0}{1}: [radius] [15195]: (info): RADIUS: Vendor, Cisco [26] 29
    2023/08/10 14:35:37.807709459 {wncd_x_R0-0}{1}: [radius] [15195]: (info): RADIUS: Cisco AVpair [1] 23 "service-type=Outbound"
    2023/08/10 14:35:37.807711783 {wncd_x_R0-0}{1}: [radius] [15195]: (info): RADIUS: Vendor, Cisco [26] 22
    2023/08/10 14:35:37.807714509 {wncd_x_R0-0}{1}: [radius] [15195]: (info): RADIUS: Cisco AVpair [1] 16 "method=webauth"
    [...]
    2023/08/10 14:35:37.887128821 {wncd_x_R0-0}{1}: [radius] [15195]: (info): RADIUS: Received from id 1812/1 192.168.1.7:0, Access-Accept, len 130
    2023/08/10 14:35:37.887152085 {wncd_x_R0-0}{1}: [radius] [15195]: (info): RADIUS: authenticator c1 c5 a3 4b 49 5d 11 42 - 74 50 bd e7 37 f3 07 1f
    2023/08/10 14:35:37.887166342 {wncd_x_R0-0}{1}: [radius] [15195]: (info): RADIUS: User-Name [1] 7 "tiago"
    [...]
    2023/08/10 14:35:37.890143566 {wncd_x_R0-0}{1}: [auth-mgr] [15195]: (info): [0429.2ec9.e371:capwap_90000010] Authc success from WebAuth, Auth event success
    [...]
    2023/08/10 14:35:37.893926155 {wncd_x_R0-0}{1}: [rog-proxy-capwap] [15195]: (debug): Managed client RUN state notification: 0429.2ec9.e371
    2023/08/10 14:35:37.893979316 {wncd_x_R0-0}{1}: [client-orch-state] [15195]: (note): MAC: 0429.2ec9.e371 Client state transition: S_CO_L3_AUTH_IN_PROGRESS -> S_CO_RUN
    [...]

    Référez-vous au document Configurer et dépanner l'authentification Web externe sur le WLC 9800 pour des étapes de dépannage plus détaillées.

    DETTE avec CWA

    Ici, nous pouvons voir un exemple de CWA dans les traces RA :

    2023/08/11 12:43:45.551148898 {wncd_x_R0-0}{1}: [client-orch-sm] [15200]: (note): MAC: 2495.2f72.8a66 Association received. BSSID 00df.1ddd.7d39, WLAN wifi6E_CWA, Slot 3 AP 00df.1ddd.7d30, AP9136_5C.F524
    2023/08/11 12:43:45.551185236 {wncd_x_R0-0}{1}: [client-orch-sm] [15200]: (debug): MAC: 2495.2f72.8a66 Received Dot11 association request. Processing started,SSID: wifi6E_CWA, Policy profile: CWA_PP, AP Name: AP9136_5C.F524, Ap Mac Address: 00df.1ddd.7d30BSSID MAC0000.0000.0000wlan ID: 7RSSI: -57, SNR: 41
    [...]
    2023/08/11 12:43:45.551873379 {wncd_x_R0-0}{1}: [client-auth] [15200]: (note): MAC: 2495.2f72.8a66 MAB Authentication initiated. Policy VLAN 0, AAA override = 1, NAC = 1
    2023/08/11 12:43:45.551925177 {wncd_x_R0-0}{1}: [auth-mgr] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] Session Start event called from SANET-SHIM, vlan: 0
    2023/08/11 12:43:45.551935427 {wncd_x_R0-0}{1}: [auth-mgr] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] Wireless session sequence, create context with method MAB
    2023/08/11 12:43:45.551947760 {wncd_x_R0-0}{1}: [auth-mgr-feat_wireless] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] - authc_list: RadiusAuthor
    [...]
    2023/08/11 12:43:45.553164283 {wncd_x_R0-0}{1}: [mab] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] MAB authentication started for 2495.2f72.8a66
    [...]
    2023/08/11 12:43:45.553769929 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Send Access-Request to 192.168.1.7:1812 id 0/19, len 394
    2023/08/11 12:43:45.553775189 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: authenticator e6 c2 9a 48 f2 59 6a 1a - ad 7b 53 0f 78 96 3a f5
    2023/08/11 12:43:45.553778666 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: User-Name [1] 14 "24952f728a66"
    2023/08/11 12:43:45.553781110 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: User-Password [2] 18 *
    2023/08/11 12:43:45.553786901 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Service-Type [6] 6 Call Check [10]
    2023/08/11 12:43:45.553789196 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Vendor, Cisco [26] 31
    2023/08/11 12:43:45.553792211 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Cisco AVpair [1] 25 "service-type=Call Check"
    2023/08/11 12:43:45.553795428 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Framed-MTU [12] 6 1485 
    2023/08/11 12:43:45.553797431 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Message-Authenticator[80] 18 ...
    2023/08/11 12:43:45.553814193 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: EAP-Key-Name [102] 2 *
    2023/08/11 12:43:45.553818431 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Vendor, Cisco [26] 49
    2023/08/11 12:43:45.553821036 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Cisco AVpair [1] 43 "audit-session-id=0F01A8C00000001EE49FCD0F"
    2023/08/11 12:43:45.553823100 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Vendor, Cisco [26] 18
    2023/08/11 12:43:45.553829221 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Cisco AVpair [1] 12 "method=mab"
    2023/08/11 12:43:45.553831265 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Vendor, Cisco [26] 32
    2023/08/11 12:43:45.553833720 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Cisco AVpair [1] 26 "client-iif-id=2801797648"
    2023/08/11 12:43:45.553835684 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Vendor, Cisco [26] 17
    2023/08/11 12:43:45.553838048 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Cisco AVpair [1] 11 "vlan-id=1"
    2023/08/11 12:43:45.553841395 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: NAS-IP-Address [4] 6 192.168.1.15 
    2023/08/11 12:43:45.553844270 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]
    2023/08/11 12:43:45.553846955 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: NAS-Port [5] 6 112 
    2023/08/11 12:43:45.553848758 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Vendor, Cisco [26] 34
    2023/08/11 12:43:45.553851193 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Cisco AVpair [1] 28 "cisco-wlan-ssid=wifi6E_CWA"
    2023/08/11 12:43:45.553853177 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Vendor, Cisco [26] 36
    2023/08/11 12:43:45.553855591 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Cisco AVpair [1] 30 "wlan-profile-name=wifi6E_CWA"
    2023/08/11 12:43:45.553858246 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Called-Station-Id [30] 30 "00-df-1d-dd-7d-30:wifi6E_CWA"
    2023/08/11 12:43:45.553860811 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Calling-Station-Id [31] 19 "24-95-2f-72-8a-66"
    2023/08/11 12:43:45.553863015 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Vendor, Airespace [26] 12
    2023/08/11 12:43:45.553865510 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Airespace-WLAN-ID [1] 6 7 
    2023/08/11 12:43:45.553867995 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Nas-Identifier [32] 14 "eWLC-9800-01"
    2023/08/11 12:43:45.553929331 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Started 5 sec timeout
    2023/08/11 12:43:45.570301533 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Received from id 1812/19 192.168.1.7:0, Access-Accept, len 538
    2023/08/11 12:43:45.570313767 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: authenticator 17 42 8f 8e 13 78 91 01 - 6c 89 9e cb 51 3b 69 c8
    2023/08/11 12:43:45.570319247 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: User-Name [1] 19 "24-95-2F-72-8A-66"
    2023/08/11 12:43:45.570321902 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Class [25] 51 ...
    2023/08/11 12:43:45.570375383 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Message-Authenticator[80] 18 ...
    2023/08/11 12:43:45.570390662 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Vendor, Cisco [26] 33
    2023/08/11 12:43:45.570393618 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Cisco AVpair [1] 27 "url-redirect-acl=REDIRECT"
    2023/08/11 12:43:45.570395732 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Vendor, Cisco [26] 208
    2023/08/11 12:43:45.570403947 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Cisco AVpair [1] 183 "url-redirect=https://192.168.1.7:8443/portal/gateway?sessionId=0F01A8C00000001EE49FCD0F&portal=26d19560-2e58-11e9-98fb-0050568775a3&action=cwa&token=a6a62b8619182aa81bd9f9f1781184f9"
    2023/08/11 12:43:45.570435186 {wncd_x_R0-0}{1}: [radius] [15200]: (info): Valid Response Packet, Free the identifier
    2023/08/11 12:43:45.570612622 {wncd_x_R0-0}{1}: [mab] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] MAB received an Access-Accept for (2495.2f72.8a66)
    2023/08/11 12:43:45.570621699 {wncd_x_R0-0}{1}: [mab] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] Received event 'MAB_RESULT' on (2495.2f72.8a66)
    2023/08/11 12:43:45.570648140 {wncd_x_R0-0}{1}: [auth-mgr] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] Authc success from MAB, Auth event success
    2023/08/11 12:43:45.570657648 {wncd_x_R0-0}{1}: [auth-mgr] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] Raised event APPLY_USER_PROFILE (14)
    2023/08/11 12:43:45.570668839 {wncd_x_R0-0}{1}: [auth-mgr] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] Raised event RX_METHOD_AUTHC_SUCCESS (3)
    2023/08/11 12:43:45.570709836 {wncd_x_R0-0}{1}: [aaa-attr-inf] [15200]: (info): Applying Attribute : username 0 "24-95-2F-72-8A-66"
    2023/08/11 12:43:45.570718393 {wncd_x_R0-0}{1}: [aaa-attr-inf] [15200]: (info): Applying Attribute : class 0 43 41 43 53 3a 30 46 30 31 41 38 43 30 30 30 30 30 30 30 31 45 45 34 39 46 43 44 30 46 3a 49 53 45 2d 30 31 2f 34 38 31 31 32 30 33 32 39 2f 32 31 
    2023/08/11 12:43:45.570719545 {wncd_x_R0-0}{1}: [aaa-attr-inf] [15200]: (info): Applying Attribute : Message-Authenticator 0 
    
    
    2023/08/11 12:43:45.570720517 {wncd_x_R0-0}{1}: [aaa-attr-inf] [15200]: (info): Applying Attribute : url-redirect-acl 0 "REDIRECT"
    2023/08/11 12:43:45.570722440 {wncd_x_R0-0}{1}: [aaa-attr-inf] [15200]: (info): Applying Attribute : url-redirect 0 "https://192.168.1.7:8443/portal/gateway?sessionId=0F01A8C00000001EE49FCD0F&portal=26d19560-2e58-11e9-98fb-0050568775a3&action=cwa&token=a6a62b8619182aa81bd9f9f1781184f9"
    [...]
    2023/08/11 12:43:45.571261140 {wncd_x_R0-0}{1}: [webauth-dev] [15200]: (info): [2495.2f72.8a66][ 192.168.1.162][2001:8a0:fb91:1c00:c093:8034:ca09:9d4f] Central Webauth URL Redirect, Received a request to create a CWA session for a mac [24:95:2f:72:8a:66]
    [...]
    2023/08/11 12:43:45.571316064 {wncd_x_R0-0}{1}: [webauth-state] [15200]: (info): [2495.2f72.8a66][ 0.0.0.0]Param-map used: global
    2023/08/11 12:43:45.571318869 {wncd_x_R0-0}{1}: [webauth-state] [15200]: (info): [2495.2f72.8a66][ 0.0.0.0]State Invalid State -> INIT
    [...]
    2023/08/11 12:43:45.572346865 {wncd_x_R0-0}{1}: [dot11] [15200]: (info): MAC: 2495.2f72.8a66 dot11 send association response. Sending assoc response of length: 183 with resp_status_code: 0, DOT11_STATUS: DOT11_STATUS_SUCCESS
    [...]
    2023/08/11 12:43:45.576047520 {wncd_x_R0-0}{1}: [client-auth] [15200]: (info): MAC: 2495.2f72.8a66 Client auth-interface state transition: S_AUTHIF_ADD_MOBILE_ACK_WAIT_KM -> S_AUTHIF_PSK_AUTH_KEY_XCHNG_PENDING
    2023/08/11 12:43:45.576136850 {wncd_x_R0-0}{1}: [client-keymgmt] [15200]: (info): MAC: 2495.2f72.8a66 EAP key M1 Sent successfully
    2023/08/11 12:43:45.576138984 {wncd_x_R0-0}{1}: [client-keymgmt] [15200]: (info): MAC: 2495.2f72.8a66 Client key-mgmt state transition: S_INITPMK -> S_PTK_START
    2023/08/11 12:43:45.576247599 {mobilityd_R0-0}{1}: [mm-client] [16431]: (debug): MAC: 0000.0000.0000 Received pmk_update, sub type: 0 of XID (0) from (WNCD[0])
    2023/08/11 12:43:45.576379639 {mobilityd_R0-0}{1}: [mm-dgram-io] [16431]: (debug): MAC: 0000.0000.0000 Sending message: pmk_update to group: holyfountain
    2023/08/11 12:43:45.576397212 {mobilityd_R0-0}{1}: [mm-dgram-io] [16431]: (debug): MAC: 0000.0000.0000 Failed to send message: pmk_update, total configured peers: 2, no active peers
    2023/08/11 12:43:45.632584865 {wncd_x_R0-0}{1}: [client-keymgmt] [15200]: (info): MAC: 2495.2f72.8a66 M2 Status: EAP key M2 validation success
    2023/08/11 12:43:45.632765557 {wncd_x_R0-0}{1}: [client-keymgmt] [15200]: (info): MAC: 2495.2f72.8a66 EAP key M3 Sent successfully
    2023/08/11 12:43:45.632766960 {wncd_x_R0-0}{1}: [client-keymgmt] [15200]: (info): MAC: 2495.2f72.8a66 Client key-mgmt state transition: S_PTK_START -> S_PTKINITNEGOTIATING
    2023/08/11 12:43:45.641844995 {wncd_x_R0-0}{1}: [client-keymgmt] [15200]: (info): MAC: 2495.2f72.8a66 M4 Status: EAP key M4 validation is successful
    2023/08/11 12:43:45.641846798 {wncd_x_R0-0}{1}: [client-keymgmt] [15200]: (note): MAC: 2495.2f72.8a66 EAP Key management successful. AKM:OWE Cipher:CCMP WPA Version: WPA3
    2023/08/11 12:43:45.641851597 {wncd_x_R0-0}{1}: [client-keymgmt] [15200]: (info): MAC: 2495.2f72.8a66 Client key-mgmt state transition: S_PTKINITNEGOTIATING -> S_PTKINITDONE
    [...]
    2023/08/11 12:43:45.645536693 {wncd_x_R0-0}{1}: [client-orch-state] [15200]: (note): MAC: 2495.2f72.8a66 Client state transition: S_CO_DPATH_PLUMB_IN_PROGRESS -> S_CO_IP_LEARN_IN_PROGRESS
    [...]
    2023/08/11 12:43:46.103210515 {wncd_x_R0-0}{1}: [client-iplearn] [15200]: (note): MAC: 2495.2f72.8a66 Client IP learn successful. Method: DHCP IP: 192.168.1.162
    2023/08/11 12:43:46.103745268 {wncd_x_R0-0}{1}: [auth-mgr] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] auth mgr attr add/change notification is received for attr addr(8)
    2023/08/11 12:43:46.104324815 {wncd_x_R0-0}{1}: [webauth-sess] [15200]: (info): [2495.2f72.8a66][ 0.0.0.0]Change notif CB, Add address 192.168.1.162 [2495.2f72.8a66]
    2023/08/11 12:43:46.104343430 {wncd_x_R0-0}{1}: [webauth-sess] [15200]: (info): adding webauth session to ipv4 hash table for vrf id 0, ipv4 vrf table id 0
    2023/08/11 12:43:46.104416388 {wncd_x_R0-0}{1}: [auth-mgr-feat_acct] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] SM Notified attribute Add/Update addr 192.168.1.162
    2023/08/11 12:43:46.104460371 {wncd_x_R0-0}{1}: [client-iplearn] [15200]: (info): MAC: 2495.2f72.8a66 IP-learn state transition: S_IPLEARN_IN_PROGRESS -> S_IPLEARN_COMPLETE
    2023/08/11 12:43:46.104607690 {wncd_x_R0-0}{1}: [client-orch-sm] [15200]: (debug): MAC: 2495.2f72.8a66 Received ip learn response. method: IPLEARN_METHOD_DHCP
    2023/08/11 12:43:46.104669668 {wncd_x_R0-0}{1}: [client-orch-sm] [15200]: (debug): MAC: 2495.2f72.8a66 Triggered L3 authentication. status = 0x0, Success
    2023/08/11 12:43:46.104674096 {wncd_x_R0-0}{1}: [client-orch-state] [15200]: (note): MAC: 2495.2f72.8a66 Client state transition: S_CO_IP_LEARN_IN_PROGRESS -> S_CO_L3_AUTH_IN_PROGRESS
    2023/08/11 12:43:46.104749168 {wncd_x_R0-0}{1}: [dot1x] [15200]: (info): [0000.0000.0000:capwap_9000000f] Couldn't find the supplicant in the list
    2023/08/11 12:43:46.104996176 {wncd_x_R0-0}{1}: [client-auth] [15200]: (note): MAC: 2495.2f72.8a66 L3 Authentication initiated. CWA 
    2023/08/11 12:43:46.105004562 {wncd_x_R0-0}{1}: [client-auth] [15200]: (info): MAC: 2495.2f72.8a66 Client auth-interface state transition: S_AUTHIF_L2_WEBAUTH_DONE -> S_AUTHIF_WEBAUTH_PENDING
    [...]
    2023/08/11 12:43:46.281818709 {wncd_x_R0-0}{1}: [webauth-state] [15200]: (info): [2495.2f72.8a66][ 192.168.1.162]Param-map used: global
    2023/08/11 12:43:46.281822877 {wncd_x_R0-0}{1}: [webauth-state] [15200]: (info): [2495.2f72.8a66][ 192.168.1.162]State INIT -> GET_REDIRECT
    2023/08/11 12:43:46.281825292 {wncd_x_R0-0}{1}: [webauth-io] [15200]: (info): [2495.2f72.8a66][ 192.168.1.162]43506/5 IO state READING -> WRITING
    2023/08/11 12:43:46.281856060 {wncd_x_R0-0}{1}: [webauth-io] [15200]: (info): [2495.2f72.8a66][ 192.168.1.162]43506/5 IO state WRITING -> END
    2023/08/11 12:43:46.281857933 {wncd_x_R0-0}{1}: [webauth-httpd] [15200]: (info): [2495.2f72.8a66][ 192.168.1.162]43506/5 Remove IO ctx and close socket, id [8800000D]
    [...]
    2023/08/11 12:44:20.312534457 {wncd_x_R0-0}{1}: [caaa-ch] [15200]: (info): [CAAA:COMMAND HANDLER:35000014] Processing CoA request under Command Handler ctx.
    2023/08/11 12:44:20.312571788 {wncd_x_R0-0}{1}: [caaa-ch] [15200]: (info): [CAAA:COMMAND HANDLER:35000014] Reauthenticate request (0x560210e99bf8) for 2495.2f72.8a66
    2023/08/11 12:44:20.312626401 {wncd_x_R0-0}{1}: [sadb-attr] [15200]: (info): Removing ipv6 addresses from the attr list 318769545,sm_ctx = 0x80806aea40, num_ipv6 = 3
    2023/08/11 12:44:20.312673230 {wncd_x_R0-0}{1}: [mab] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] MAB re-authentication started for (2495.2f72.8a66)
    2023/08/11 12:44:20.312713736 {wncd_x_R0-0}{1}: [auth-mgr] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] Context changing state from 'Authz Success' to 'Running'
    2023/08/11 12:44:20.312720158 {wncd_x_R0-0}{1}: [auth-mgr] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] Method mab changing state from 'Authc Success' to 'Running'
    2023/08/11 12:44:20.312740637 {wncd_x_R0-0}{1}: [aaa-coa] [15200]: (info): radius coa proxy relay coa resp(wncd)
    2023/08/11 12:44:20.312746478 {wncd_x_R0-0}{1}: [aaa-coa] [15200]: (info): CoA Response Details
    2023/08/11 12:44:20.312756237 {wncd_x_R0-0}{1}: [aaa-attr-inf] [15200]: (info): << ssg-command-code 0 32 >>
    2023/08/11 12:44:20.312758912 {wncd_x_R0-0}{1}: [aaa-attr-inf] [15200]: (info): << formatted-clid 0 "2495.2f72.8a66">>
    2023/08/11 12:44:20.312762318 {wncd_x_R0-0}{1}: [aaa-attr-inf] [15200]: (info): << error-cause 0 1 [Success]>>
    2023/08/11 12:44:20.312774040 {wncd_x_R0-0}{1}: [aaa-coa] [15200]: (info): server:192.168.1.15 cfg_saddr:192.168.1.15 udpport:42721 sport:0, tableid:0iden:4 rad_code:43 msg_auth_rcvd:TRUE coa_resp:ACK
    2023/08/11 12:44:20.312876905 {wncd_x_R0-0}{1}: [caaa-ch] [15200]: (info): [CAAA:COMMAND HANDLER] CoA response sent
    2023/08/11 12:44:20.312886633 {wncd_x_R0-0}{1}: [caaa-ch] [15200]: (info): [CAAA:COMMAND HANDLER:35000014] Identity preserved: mac (2495.2f72.8a66), ip (0), audit_sid (0F01A8C00000001EE49FCD0F), aaa_session_id (0)
    2023/08/11 12:44:20.312902744 {wncd_x_R0-0}{1}: [mab] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] Received event 'MAB_REAUTHENTICATE' on (2495.2f72.8a66)
    2023/08/11 12:44:20.313249801 {wncd_x_R0-0}{1}: [sadb-attr] [15200]: (info): Removing ipv6 addresses from the attr list -855635574,sm_ctx = 0x80806aea40, num_ipv6 = 3
    2023/08/11 12:44:20.313380288 {wncd_x_R0-0}{1}: [caaa-author] [15200]: (info): [CAAA:AUTHOR:35000014] NULL ATTR LIST 
    2023/08/11 12:44:20.313702758 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Send Access-Request to 192.168.1.7:1812 id 0/20, len 544
    2023/08/11 12:44:20.313714140 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: authenticator 7b 62 36 99 3d 55 15 f1 - c3 b9 08 ea 93 7f 26 79
    2023/08/11 12:44:20.313722686 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: User-Name [1] 14 "24952f728a66"
    [...]
    2023/08/11 12:44:20.313914609 {smd_R0-0}{1}: [aaa-coa] [17281]: (info): ++++++ Received CoA response Attribute List ++++++
    2023/08/11 12:44:20.313917665 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: NAS-IP-Address [4] 6 192.168.1.15 
    2023/08/11 12:44:20.313924488 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]
    2023/08/11 12:44:20.313931051 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: NAS-Port [5] 6 112 
    2023/08/11 12:44:20.313935559 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Vendor, Cisco [26] 34
    2023/08/11 12:44:20.313941611 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Cisco AVpair [1] 28 "cisco-wlan-ssid=wifi6E_CWA"
    2023/08/11 12:44:20.313946640 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Vendor, Cisco [26] 36
    2023/08/11 12:44:20.313952692 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Cisco AVpair [1] 30 "wlan-profile-name=wifi6E_CWA"
    2023/08/11 12:44:20.313959174 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Called-Station-Id [30] 30 "00-df-1d-dd-7d-30:wifi6E_CWA"
    2023/08/11 12:44:20.313965616 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Calling-Station-Id [31] 19 "24-95-2f-72-8a-66"
    2023/08/11 12:44:20.313978210 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Vendor, Airespace [26] 12
    2023/08/11 12:44:20.313978350 {smd_R0-0}{1}: [radius] [17281]: (info): RADIUS(00000000): Send CoA Ack Response to 192.168.1.7:42721 id 4, len 69
    2023/08/11 12:44:20.313984442 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Airespace-WLAN-ID [1] 6 7 
    2023/08/11 12:44:20.313989972 {smd_R0-0}{1}: [radius] [17281]: (info): RADIUS: authenticator c3 10 c5 26 16 87 54 7f - 9f 63 a2 03 db 61 3a 65
    2023/08/11 12:44:20.313990713 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Nas-Identifier [32] 14 "eWLC-9800-01"
    2023/08/11 12:44:20.313993459 {smd_R0-0}{1}: [radius] [17281]: (info): RADIUS: Vendor, Cisco [26] 9
    2023/08/11 12:44:20.313996655 {smd_R0-0}{1}: [radius] [17281]: (info): RADIUS: ssg-command-code [252] 3 ...
    2023/08/11 12:44:20.314073240 {smd_R0-0}{1}: [radius] [17281]: (info): RADIUS: Calling-Station-Id [31] 16 "2495.2f72.8a66"
    2023/08/11 12:44:20.314077337 {smd_R0-0}{1}: [radius] [17281]: (info): RADIUS: Dynamic-Author-Error-Cause[101] 6 Success [200]
    2023/08/11 12:44:20.314079431 {smd_R0-0}{1}: [radius] [17281]: (info): RADIUS: Message-Authenticator[80] 18 ...
    2023/08/11 12:44:20.314098387 {smd_R0-0}{1}: [aaa-pod] [17281]: (info): CoA response source port = 0, udpport = 42721, 
    2023/08/11 12:44:20.314099289 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Started 5 sec timeout
    2023/08/11 12:44:20.327831023 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Received from id 1812/20 192.168.1.7:0, Access-Accept, len 131
    2023/08/11 12:44:20.327850400 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: authenticator a6 13 03 f0 f7 62 06 e0 - f3 c6 95 6e 36 cb 13 0b
    2023/08/11 12:44:20.327861140 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: User-Name [1] 7 "tiago"
    2023/08/11 12:44:20.327867512 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Class [25] 51 ...
    2023/08/11 12:44:20.327938827 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Message-Authenticator[80] 18 ...
    2023/08/11 12:44:20.327978472 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Vendor, Cisco [26] 35
    2023/08/11 12:44:20.327985516 {wncd_x_R0-0}{1}: [radius] [15200]: (info): RADIUS: Cisco AVpair [1] 29 "profile-name=Android-Google"
    2023/08/11 12:44:20.328027385 {wncd_x_R0-0}{1}: [radius] [15200]: (info): Valid Response Packet, Free the identifier
    2023/08/11 12:44:20.328322423 {wncd_x_R0-0}{1}: [mab] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] MAB received an Access-Accept for (2495.2f72.8a66)
    2023/08/11 12:44:20.328341299 {wncd_x_R0-0}{1}: [mab] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] Received event 'MAB_RESULT' on (2495.2f72.8a66)
    2023/08/11 12:44:20.328394871 {wncd_x_R0-0}{1}: [auth-mgr] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] Authc success from MAB, Auth event success
    2023/08/11 12:44:20.328412885 {wncd_x_R0-0}{1}: [auth-mgr] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] Raised event APPLY_USER_PROFILE (14)
    2023/08/11 12:44:20.328421270 {wncd_x_R0-0}{1}: [auth-mgr] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] Raised event RX_METHOD_AUTHC_SUCCESS (3)
    2023/08/11 12:44:20.328519506 {wncd_x_R0-0}{1}: [aaa-attr-inf] [15200]: (info): Applying Attribute : username 0 "tiago"
    [...]
    2023/08/11 12:44:20.328759310 {wncd_x_R0-0}{1}: [auth-mgr] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] Received User-Name tiago for client 2495.2f72.8a66
    2023/08/11 12:44:20.328773066 {wncd_x_R0-0}{1}: [auth-mgr] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] Method mab changing state from 'Running' to 'Authc Success'
    2023/08/11 12:44:20.328791892 {wncd_x_R0-0}{1}: [auth-mgr] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] Context changing state from 'Running' to 'Authc Success'
    [...]
    2023/08/11 12:44:20.330928236 {wncd_x_R0-0}{1}: [auth-mgr] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] Raised event AUTHZ_SUCCESS (11)
    2023/08/11 12:44:20.330937604 {wncd_x_R0-0}{1}: [auth-mgr] [15200]: (info): [2495.2f72.8a66:capwap_9000000f] Context changing state from 'Authc Success' to 'Authz Success'
    2023/08/11 12:44:20.331059194 {wncd_x_R0-0}{1}: [client-auth] [15200]: (note): MAC: 2495.2f72.8a66 L3 Authentication Successful. ACL:[]
    2023/08/11 12:44:20.331065276 {wncd_x_R0-0}{1}: [client-auth] [15200]: (info): MAC: 2495.2f72.8a66 Client auth-interface state transition: S_AUTHIF_WEBAUTH_PENDING -> S_AUTHIF_WEBAUTH_DONE
    [...]
    2023/08/11 12:44:20.332171950 {wncd_x_R0-0}{1}: [errmsg] [15200]: (info): %CLIENT_ORCH_LOG-6-CLIENT_ADDED_TO_RUN_STATE: R0/0: wncd: Username entry (tiago) joined with ssid (wifi6E_CWA) for device with MAC: 2495.2f72.8a66
    [...]
    2023/08/11 12:44:20.332437363 {wncd_x_R0-0}{1}: [rog-proxy-capwap] [15200]: (debug): Managed client RUN state notification: 2495.2f72.8a66
    2023/08/11 12:44:20.332544836 {wncd_x_R0-0}{1}: [client-orch-state] [15200]: (note): MAC: 2495.2f72.8a66 Client state transition: S_CO_L3_AUTH_IN_PROGRESS -> S_CO_RUN
    [...]
    2023/08/11 12:44:20.337221359 {wncd_x_R0-0}{1}: [client-auth] [15200]: (info): MAC: 2495.2f72.8a66 Client auth-interface state transition: S_AUTHIF_WEBAUTH_DONE -> S_AUTHIF_WEBAUTH_DONE

    Référez-vous au document Configure Central Web Authentication (CWA) on Catalyst 9800 WLC and ISE pour des étapes de dépannage plus détaillées.

    Informations connexes

    Qu'est-ce que le Wi-Fi 6E ?

    Qu'est-ce que le Wi-Fi 6 et le Wi-Fi 6E ?

    Wi-Fi 6E en quelques mots

    Wi-Fi 6E : le prochain grand chapitre du livre blanc sur le Wi-Fi

    Cisco Live : concevoir un réseau sans fil de nouvelle génération avec des points d'accès Wi-Fi 6E Catalyst

    Guide de configuration du logiciel du contrôleur sans fil Cisco Catalyst 9800 17.9.x

    Guide de déploiement WPA3

    Configurer l'authentification Web locale avec l'authentification externe

    Configurer l'authentification Web centrale (CWA) sur le WLC Catalyst 9800 et ISE

    Historique de révision

    Révision Date de publication Commentaires
    1.0
    14-Aug-2023
    Première publication
    TAC Authored

    Contribution d’experts de Cisco

    • Tiago Antunes
      TAC Cisco

    Ce document vous est-il utile?

    FeedbackCommentaires

    Contacter Cisco

    Ce document s’applique à ces produits