- Quick Links to Catalyst 4500 Series Switch Cisco IOS Commands
- Index
- Preface
- aaa accounting dot1x default start-stop group radius through instance
- interface port-channel through shape
- Command-Line Interface
- show access-group mode interface through show vtp
- snmp ifindex clear through vtp v2-mode
- Acronyms and Abbreviations
- show access-group mode interface
- show adjacency
- show ancp multicast
- show arp access-list
- show authentication
- show auto install status
- show auto qos
- show bootflash:
- show bootvar
- show cable-diagnostics tdr
- show call-home
- show cdp neighbors
- show class-map
- show diagnostic content
- show diagnostic result module
- show diagnostic result module test
- show diagnostic result module test 2
- show diagnostic result module test 3
- show dot1x
- show energywise
- show environment
- show errdisable detect
- show errdisable recovery
- show etherchannel
- show flowcontrol
- show hw-module port-group
- show hw-module uplink
- show idprom
- show interfaces
- show interfaces capabilities
- show interfaces counters
- show interfaces description
- show interfaces link
- show interfaces mtu
- show interfaces private-vlan mapping
- show interfaces status
- show interfaces switchport
- show interfaces transceiver
- show interfaces trunk
- show ip arp inspection
- show ip arp inspection log
- show ip cef vlan
- show ip dhcp snooping
- show ip dhcp snooping binding
- show ip dhcp snooping database
- show ip igmp interface
- show ip igmp profile
- show ip igmp snooping
- show ip igmp snooping membership
- show ip igmp snooping mrouter
- show ip igmp snooping vlan
- show ip interface
- show ip mfib
- show ip mfib fastdrop
- show ip mroute
- show ip source binding
- show ip verify source
- show ipc
- show ipv6 mld snooping
- show ipv6 mld snooping mrouter
- show ipv6 mld snooping querier
- show issu capability
- show issu clients
- show issu comp-matrix
- show issu endpoints
- show issu entities
- show issu fsm
- show issu message
- show issu negotiated
- show issu rollback-timer
- show issu sessions
- show issu state
- show l2protocol-tunnel
- show lacp
- show mab
- show mac access-group interface
- show mac-address-table address
- show mac-address-table aging-time
- show mac-address-table count
- show mac-address-table dynamic
- show mac-address-table interface
- show mac-address-table multicast
- show mac-address-table notification
- show mac-address-table protocol
- show mac-address-table static
- show mac-address-table vlan
- show module
- show monitor
- show nmsp
- show pagp
- show policy-map
- show policy-map control-plane
- show policy-map interface
- show policy-map interface vlan
- show port-security
- show power
- show power inline police
- show pppoe intermediate-agent interface
- show qos
- show qos aggregate policer
- show qos dbl
- show qos interface
- show qos maps
- show redundancy
- show redundancy config-sync
- show running-config
- show slavebootflash:
- show slaveslot0:
- show slot0:
- show spanning-tree
- show spanning-tree mst
- show storm-control
- show system mtu
- show tech-support
- show udld
- show vlan
- show vlan access-map
- show vlan counters
- show vlan dot1q tag native
- show vlan internal usage
- show vlan mtu
- show vlan private-vlan
- show vlan remote-span
- show vmps
- show vtp
show access-group mode interface
To display the ACL configuration on a Layer 2 interface, use the show access-group mode interface command.
show access-group mode interface [interface interface-number]
Syntax Description
interface |
(Optional) Interface type; valid values are ethernet, fastethernet, gigabitethernet, tengigabitethernet, and port-channel. |
interface-number |
(Optional) Interface number. |
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
The valid values for the port number depend on the chassis used.
Examples
This example shows how to display the ACL configuration on the Fast Ethernet interface 6/1:
Switch# show access-group mode interface fa6/1
Interface FastEthernet6/1:
Access group mode is: merge
Switch#
Related Commands
|
|
---|---|
Specifies the override modes (for example, VACL overrides PACL) and the non-override modes (for example, merge or strict mode). |
show adjacency
To display information about the Layer 3 switching adjacency table, use the show adjacency command.
show adjacency [{interface interface-number} | {null interface-number} | {port-channel number} | {vlan vlan-id} | detail | internal | summary]
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
|
|
---|---|
12.2(25)EW |
Extended to include the 10-Gigabit Ethernet interface. |
Usage Guidelines
The interface-number argument designates the module and port number. Valid values for interface-number depend on the specified interface type and the chassis and module that are used. For example, if you specify a Gigabit Ethernet interface and have a 48-port 10/100BASE-T Ethernet module that is installed in a 13-slot chassis, valid values for the module number are from 1 to 13, and valid values for the port number are from 1 to 48.
Hardware Layer 3 switching adjacency statistics are updated every 60 seconds.
The following information is contained in the show adjacency command:
•Protocol interface.
•Type of routing protocol that is configured on the interface.
•Interface address.
•Method of adjacency that was learned.
•MAC address of the adjacent router.
•Time left before the adjacency rolls out of the adjacency table. After it rolls out, a packet must use the same next hop to the destination.
Examples
This example shows how to display adjacency information:
Switch# show adjacency
Protocol Interface Address
IP FastEthernet2/3 172.20.52.1(3045)
IP FastEthernet2/3 172.20.52.22(11)
Switch#
This example shows how to display a summary of adjacency information:
Switch# show adjacency summary
Adjacency Table has 2 adjacencies
Interface Adjacency Count
FastEthernet2/3 2
Switch#
This example shows how to display protocol detail and timer information:
Switch# show adjacency detail
Protocol Interface Address
IP FastEthernet2/3 172.20.52.1(3045)
0 packets, 0 bytes
000000000FF920000380000000000000
00000000000000000000000000000000
00605C865B2800D0BB0F980B0800
ARP 03:58:12
IP FastEthernet2/3 172.20.52.22(11)
0 packets, 0 bytes
000000000FF920000380000000000000
00000000000000000000000000000000
00801C93804000D0BB0F980B0800
ARP 03:58:06
Switch#
This example shows how to display adjacency information for a specific interface:
Switch# show adjacency fastethernet2/3
Protocol Interface Address
IP FastEthernet2/3 172.20.52.1(3045)
IP FastEthernet2/3 172.20.52.22(11)
Switch#
Related Commands
|
|
---|---|
Displays information about the adjacency debugging. |
show ancp multicast
To display multicast streams activated by ANCP, use the show ancp multicast command.
show ancp multicast [group groupaddr] [source sourceaddr] | [ interface interfacename]
Syntax Description
Defaults
Displays all the multicast streams activated with ANCP.
Command Modes
Privileged EXEC
Command History
|
|
---|---|
12.2(50)SG |
Support for this command was introduced on the Catalyst 4500 series switch. |
Usage Guidelines
This table of multicast streams on the box that have been activated with ANCP should match what is displayed on the standby table because its content is replicated for best availability.
Examples
This example shows how to display multicast streams activated by ANCP:
ANCP-Client# show ancp mul
ANCP Multicast Streams
ClientID VLAN Interface Joined on
Group 235.3.2.1
0x01060004000A0703 10 Fa7/3 18:27:35 UTC Sat Sep 13 2008
0x0106000400140703 20 Fa7/3 18:27:35 UTC Sat Sep 13 2008
0x01060004000A0704 10 Fa7/4 18:25:43 UTC Sat Sep 13 2008
0x0106000400140704 20 Fa7/4 18:25:43 UTC Sat Sep 13 2008
Group 238.1.2.3
0x01060004000A0703 10 Fa7/3 18:27:37 UTC Sat Sep 13 2008
0x0106000400140703 20 Fa7/3 18:27:35 UTC Sat Sep 13 2008
0x01060004000A0704 10 Fa7/4 18:25:43 UTC Sat Sep 13 2008
0x0106000400140704 20 Fa7/4 18:25:43 UTC Sat Sep 13 2008
ANCP-Client#
show arp access-list
To display detailed information on an ARP access list, use the show arp command.
show arp access-list
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
|
|
---|---|
12.1(19)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Examples
This example shows how to display the ARP ACL information for a switch:
Switch# show arp access-list
ARP access list rose
permit ip 10.101.1.1 0.0.0.255 mac any
permit ip 20.3.1.0 0.0.0.255 mac any
Related Commands
show authentication
To display the Auth Manager information, use the show authentication command in EXEC or Privileged EXEC mode.
show authentication {interface interface | registrations | sessions [session-id session-id] [handle handle] [interface interface] [mac mac] [method method]
Syntax Description
Command Default
None
Command Modes
EXEC
Command History
|
|
---|---|
12.2(50)SG |
This command was introduced. |
Usage Guidelines
Table 2-13 describes the significant fields shown in the show authentication display.
Note The possible values for the status of sessions are given below. For a session in terminal state, "Authz Success" or "Authz Failed" are displayed, with "No methods" if no method has provided a result.
Table 2-14 lists the possible values for the state of methods. For a session in terminal state, "Authc Success," "Authc Failed," or "Failed over" are displayed (the latter indicates a method ran and failed over to the next method which did not provide a result), with "Not run" in the case of sessions that are synchronized on standby.
Examples
The following example shows how to display authentication methods registered with Auth Manager:
Switch# show authentication registrations
Auth Methods registered with the Auth Manager:
Handle Priority Name
3 0 dot1x
2 1 mab
1 2 webauth
Switch#
The following example shows how to display Auth Manager details for a specific interface:
Switch# show authentication interface gigabitethernet1/23
Client list:
MAC Address Domain Status Handle Interface
000e.84af.59bd DATA Authz Success 0xE0000000 GigabitEthernet1/0/23
Available methods list:
Handle Priority Name
3 0 dot1x
Runnable methods list:
Handle Priority Name
3 0 dot1x
Switch#
The following example shows how to display all Auth Manager sessions on the switch:
Switch# show authentication sessions
Interface MAC Address Method Domain Status Session ID
Gi3/45 (unknown) N/A DATA Authz Failed 0908140400000007003651EC
Gi3/46 (unknown) N/A DATA Authz Success 09081404000000080057C274
The following example shows how to display all Auth Manager sessions on an interface:
Switch# show authentication sessions int gi 3/46
Interface: GigabitEthernet3/46
MAC Address: Unknown
IP Address: Unknown
Status: Authz Success
Domain: DATA
Oper host mode: multi-host
Oper control dir: both
Authorized By: Guest Vlan
Vlan Policy: 4094
Session timeout: N/A
Idle timeout: N/A
Common Session ID: 09081404000000080057C274
Acct Session ID: 0x0000000A
Handle: 0xCC000008
Runnable methods list:
Method State
dot1x Failed over
The following example shows how to display Auth Manager session for a specified MAC address:
Switch# show authentication sessions mac 000e.84af.59bd
Interface: GigabitEthernet1/23
MAC Address: 000e.84af.59bd
Status: Authz Success
Domain: DATA
Oper host mode: single-host
Authorized By: Authentication Server
Vlan Policy: 10
Handle: 0xE0000000
Runnable methods list:
Method State
dot1x Authc Success
Switch#
The following example shows how to display all clients authorized via a specified auth method:
Switch# show authentication sessions method mab
No Auth Manager contexts match supplied criteria
Switch# show authentication sessions method dot1x
MAC Address Domain Status Handle Interface
000e.84af.59bd DATA Authz Success 0xE0000000 GigabitEthernet1/23
Switch#
Related Commands
show auto install status
To display the status of an automatic installation, use the show auto install status command.
show auto install status
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.2(20)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Examples
This example shows how to display the IP address of the TFTP server and to display whether or not the switch is currently acquiring the configuration file on the TFTP server:
Switch# show auto install status
Status : Downloading config file
DHCP Server : 20.0.0.1
TFTP Server : 30.0.0.3
Config File Fetched : Undetermined
The first IP address in the display indicates the server that is used for the automatic installation. The second IP address indicates the TFTP server that provided the configuration file.
show auto qos
To display the automatic quality of service (auto-QoS) configuration that is applied, use the show auto qos user EXEC command.
show auto qos [interface [interface-id]] [{begin | exclude | include} expression]
Syntax Description
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(19)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Usage Guidelines
The show auto qos interface interface-id command displays the auto-QoS configuration; it does not display any user changes to the configuration that might be in effect.
To display information about the QoS configuration that might be affected by auto-QoS on a non-Supervisor Engine 6-E, use one of these commands:
•show qos
•show qos map
•show qos interface interface-id
•show running-config
Expressions are case sensitive. For example, if you enter exclude output, the lines that contain output do not appear, but the lines that contain Output appear.
Examples
This example shows output from the show auto qos command when auto-QoS is enabled:
Switch# show auto qos
GigabitEthernet1/2
auto qos voip cisco-phone
Switch#
Related Commands
|
|
---|---|
Automatically configures quality of service (auto-QoS) for Voice over IP (VoIP) within a QoS domain. |
show bootflash:
To display information about the bootflash: file system, use the show bootflash: command.
show bootflash: [all | chips | filesys]
Syntax Description
all |
(Optional) Displays all possible Flash information. |
chips |
(Optional) Displays Flash chip information. |
filesys |
(Optional) Displays file system information. |
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
|
|
---|---|
12.1(8a)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Examples
This example shows how to display file system status information:
Switch>
show bootflash: filesys
-------- F I L E S Y S T E M S T A T U S --------
Device Number = 0
DEVICE INFO BLOCK: bootflash
Magic Number = 6887635 File System Vers = 10000 (1.0)
Length = 1000000 Sector Size = 40000
Programming Algorithm = 39 Erased State = FFFFFFFF
File System Offset = 40000 Length = F40000
MONLIB Offset = 100 Length = C628
Bad Sector Map Offset = 3FFF8 Length = 8
Squeeze Log Offset = F80000 Length = 40000
Squeeze Buffer Offset = FC0000 Length = 40000
Num Spare Sectors = 0
Spares:
STATUS INFO:
Writable
NO File Open for Write
Complete Stats
No Unrecovered Errors
No Squeeze in progress
USAGE INFO:
Bytes Used = 917CE8 Bytes Available = 628318
Bad Sectors = 0 Spared Sectors = 0
OK Files = 2 Bytes = 917BE8
Deleted Files = 0 Bytes = 0
Files w/Errors = 0 Bytes = 0
Switch>
This example shows how to display system image information:
Switch>
show bootflash:
-# - ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name
1 .. image 8C5A393A 237E3C 14 2063804 Aug 23 1999 16:18:45 c4-boot-mz
2 .. image D86EE0AD 957CE8 9 7470636 Sep 20 1999 13:48:49 rp.halley
Switch>
This example shows how to display all bootflash information:
Switch>
show bootflash: all
-# - ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name
1 .. image 8C5A393A 237E3C 14 2063804 Aug 23 1999 16:18:45 c4-boot-
mz
2 .. image D86EE0AD 957CE8 9 7470636 Sep 20 1999 13:48:49 rp.halley
6456088 bytes available (9534696 bytes used)
-------- F I L E S Y S T E M S T A T U S --------
Device Number = 0
DEVICE INFO BLOCK: bootflash
Magic Number = 6887635 File System Vers = 10000 (1.0)
Length = 1000000 Sector Size = 40000
Programming Algorithm = 39 Erased State = FFFFFFFF
File System Offset = 40000 Length = F40000
MONLIB Offset = 100 Length = C628
Bad Sector Map Offset = 3FFF8 Length = 8
Squeeze Log Offset = F80000 Length = 40000
Squeeze Buffer Offset = FC0000 Length = 40000
Num Spare Sectors = 0
Spares:
STATUS INFO:
Writable
NO File Open for Write
Complete Stats
No Unrecovered Errors
No Squeeze in progress
USAGE INFO:
Bytes Used = 917CE8 Bytes Available = 628318
Bad Sectors = 0 Spared Sectors = 0
OK Files = 2 Bytes = 917BE8
Deleted Files = 0 Bytes = 0
Files w/Errors = 0 Bytes = 0
Switch>
show bootvar
To display BOOT environment variable information, use the show bootvar command.
show bootvar
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(8a)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Examples
This example shows how to display BOOT environment variable information:
Switch#
show bootvar
BOOT variable = sup:1;
CONFIG_FILE variable does not exist
BOOTLDR variable does not exist
Configuration register is 0x0
Switch#
show cable-diagnostics tdr
To display the test results for the TDR cable diagnostics, use the show cable-diagnostics tdr command.
show cable-diagnostics tdr {interface {interface interface-number}}
Note This command will be deprecated in future Cisco IOS releases. Please use the diagnostic start command.
Syntax Description
interface interface |
Interface type; valid values are fastethernet and gigabitethernet. |
interface-number |
Module and port number. |
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
12.2(25)SG |
Support for this command was introduced on the Catalyst 4500 series switch. |
Usage Guidelines
The TDR test is supported on Catalyst 4500 series switches running Cisco IOS Release 12.2(25)SG for the following line cards only:
•WS-X4548-GB-RJ45
•WS-X4548-GB-RJ45V
•WS-X4524-GB-RJ45V
•WS-X4013+TS
•WS-C4948
•WS-C4948-10GE
The distance to the fault is displayed in meters (m).
Examples
This example shows how to display information about the TDR test:
Switch# show cable-diagnostics tdr interface gi4/13
Interface Speed Local pair Cable length Remote channel Status
Gi4/13 0Mbps 1-2 102 +-2m Unknown Fault
3-6 100 +-2m Unknown Fault
4-5 102 +-2m Unknown Fault
7-8 102 +-2m Unknown Fault
Switch#
Table 2-15 describes the fields in the show cable-diagnostics tdr command output.
Related Commands
|
|
---|---|
Tests the condition of copper cables on 48-port 10/100/1000 BASE-T modules. |
show call-home
To display the configured call-home information, use the show call-home command in privileged EXEC mode.
show call-home [alert-group | detail | mail-server | profile {all | name} | statistics]
Syntax Description
Command Default
This command has no default settings.
Command Modes
Privileged EXEC (#)
Command History
|
|
---|---|
12.2(52)SG |
This command was introduced on the Catalyst 4500 series switch, Supervisor Engine 6-E, and Catalyst 4900M chassis. |
Examples
The following example displays the configured call-home settings:
Switch# show call-home
Current call home settings:
call home feature : disable
call home message's from address: switch@example.com
call home message's reply-to address: support@example.com
vrf for call-home messages: Not yet set up
contact person's email address: technical@example.com
contact person's phone number: +1-408-555-1234
street address: 1234 Picaboo Street, Any city, Any state, 12345
customer ID: ExampleCorp
contract ID: X123456789
site ID: SantaClara
Mail-server[1]: Address: smtp.example.com Priority: 1
Mail-server[2]: Address: 192.168.0.1 Priority: 2
Rate-limit: 20 message(s) per minute
Available alert groups:
Keyword State Description
------------------------ ------- -------------------------------
configuration Disable configuration info
diagnostic Disable diagnostic info
environment Disable environmental info
inventory Enable inventory info
syslog Disable syslog info
Profiles:
Profile Name: campus-noc
Profile Name: CiscoTAC-1
Switch#
Configured Call Home Information in Detail
Switch# show call-home detail
Current call home settings:
call home feature : disable
call home message's from address: switch@example.com
call home message's reply-to address: support@example.com
vrf for call-home messages: Not yet set up
contact person's email address: technical@example.com
contact person's phone number: +1-408-555-1234
street address: 1234 Picaboo Street, Any city, Any state, 12345
customer ID: ExampleCorp
contract ID: X123456789
site ID: SantaClara
Mail-server[1]: Address: smtp.example.com Priority: 1
Mail-server[2]: Address: 192.168.0.1 Priority: 2
Rate-limit: 20 message(s) per minute
Available alert groups:
Keyword State Description
------------------------ ------- -------------------------------
configuration Disable configuration info
diagnostic Disable diagnostic info
environment Disable environmental info
inventory Enable inventory info
syslog Disable syslog info
Profiles:
Profile Name: campus-noc
Profile status: ACTIVE
Preferred Message Format: long-text
Message Size Limit: 3145728 Bytes
Transport Method: email
Email address(es): noc@example.com
HTTP address(es): Not yet set up
Alert-group Severity
------------------------ ------------
inventory normal
Syslog-Pattern Severity
------------------------ ------------
N/A N/A
Profile Name: CiscoTAC-1
Profile status: ACTIVE
Preferred Message Format: xml
Message Size Limit: 3145728 Bytes
Transport Method: email
Email address(es): callhome@cisco.com
HTTP address(es): https://tools.cisco.com/its/service/oddce/services/DDCEService
Periodic configuration info message is scheduled every 1 day of the month at 09:27
Periodic inventory info message is scheduled every 1 day of the month at 09: 12
Alert-group Severity
------------------------ ------------
diagnostic minor
environment warning
inventory normal
Syslog-Pattern Severity
------------------------ ------------
.* major
Switch#
Available Call Home Alert Groups
Switch# show call-home alert-group
Available alert groups:
Keyword State Description
------------------------ ------- -------------------------------
configuration Disable configuration info
diagnostic Disable diagnostic info
environment Disable environmental info
inventory Enable inventory info
syslog Disable syslog info
Switch#
E-Mail Server Status Information
Switch# show call-home mail-server status
Please wait. Checking for mail server status ...
Translating "smtp.example.com"
Mail-server[1]: Address: smtp.example.com Priority: 1 [Not Available]
Mail-server[2]: Address: 192.168.0.1 Priority: 2 [Not Available]
Switch#
Information for All Destination Profiles (Predefined and User-Defined)
Switch# show call-home profile all
Profile Name: campus-noc
Profile status: ACTIVE
Preferred Message Format: long-text
Message Size Limit: 3145728 Bytes
Transport Method: email
Email address(es): noc@example.com
HTTP address(es): Not yet set up
Alert-group Severity
------------------------ ------------
inventory normal
Syslog-Pattern Severity
------------------------ ------------
N/A N/A
Profile Name: CiscoTAC-1
Profile status: ACTIVE
Preferred Message Format: xml
Message Size Limit: 3145728 Bytes
Transport Method: email
Email address(es): callhome@cisco.com
HTTP address(es): https://tools.cisco.com/its/service/oddce/services/DDCEService
Periodic configuration info message is scheduled every 1 day of the month at 09:27
Periodic inventory info message is scheduled every 1 day of the month at 09:12
Alert-group Severity
------------------------ ------------
diagnostic minor
environment warning
inventory normal
Syslog-Pattern Severity
------------------------ ------------
.* major
Switch#
Information for a User-Defined Destination Profile
Switch# show call-home profile CiscoTAC-1
Profile Name: CiscoTAC-1
Profile status: INACTIVE
Preferred Message Format: xml
Message Size Limit: 3145728 Bytes
Transport Method: email
Email address(es): callhome@cisco.com
HTTP address(es): https://tools.cisco.com/its/service/oddce/services/DDCEService
Periodic configuration info message is scheduled every 11 day of the month at 11:25
Periodic inventory info message is scheduled every 11 day of the month at 11:10
Alert-group Severity
------------------------ ------------
diagnostic minor
environment warning
inventory normal
Syslog-Pattern Severity
------------------------ ------------
.* major
Call Home Statistics
Switch# show call-home statistics
Message Types Total Email HTTP
------------- -------------------- -------------------- ------------------
Total Success 0 0 0
Config 0 0 0
Diagnostic 0 0 0
Environment 0 0 0
Inventory 0 0 0
SysLog 0 0 0
Test 0 0 0
Request 0 0 0
Send-CLI 0 0 0
Total In-Queue 0 0 0
Config 0 0 0
Diagnostic 0 0 0
Environment 0 0 0
Inventory 0 0 0
SysLog 0 0 0
Test 0 0 0
Request 0 0 0
Send-CLI 0 0 0
Total Failed 0 0 0
Config 0 0 0
Diagnostic 0 0 0
Environment 0 0 0
Inventory 0 0 0
SysLog 0 0 0
Test 0 0 0
Request 0 0 0
Send-CLI 0 0 0
Total Ratelimit
-dropped 0 0 0
Config 0 0 0
Diagnostic 0 0 0
Environment 0 0 0
Inventory 0 0 0
SysLog 0 0 0
Test 0 0 0
Request 0 0 0
Send-CLI 0 0 0
Last call-home message sent time: n/a
Related Commands
|
|
---|---|
Enters call-home configuration mode. |
|
Sends a specific alert group message. |
|
service call-home (refer to Cisco IOS documentation) |
Enables or disables call home. |
show cdp neighbors
To display detailed information about the neighboring devices that are discovered through CDP, use the show cdp neighbors command.
show cdp neighbors [type number] [detail]
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.2(25)EW |
Extended to include the 10-Gigabit Ethernet interface. |
Usage Guidelines
The vlan keyword is supported in Catalyst 4500 series switches that are configured with a Supervisor Engine 2.
The port-channel values are from 0 to 282; values from 257 to 282 are supported on the CSM and the FWSM only.
Examples
This example shows how to display the information about the CDP neighbors:
Switch# show cdp neighbors
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone
Device ID Local Intrfce Holdtme Capability Platform Port ID
lab-7206 Eth 0 157 R 7206VXR Fas 0/0/0
lab-as5300-1 Eth 0 163 R AS5300 Fas 0
lab-as5300-2 Eth 0 159 R AS5300 Eth 0
lab-as5300-3 Eth 0 122 R AS5300 Eth 0
lab-as5300-4 Eth 0 132 R AS5300 Fas 0/0
lab-3621 Eth 0 140 R S 3631-telcoFas 0/0
008024 2758E0 Eth 0 132 T CAT3000 1/2
Switch#
Table 2-16 describes the fields that are shown in the example.
This example shows how to display detailed information about your CDP neighbors:
Switch# show cdp neighbors detail
-------------------------
Device ID: lab-7206
Entry address(es):
IP address: 172.19.169.83
Platform: cisco 7206VXR, Capabilities: Router
Interface: Ethernet0, Port ID (outgoing port): FastEthernet0/0/0
Holdtime : 123 sec
Version :
Cisco Internetwork Operating System Software
IOS (tm) 5800 Software (C5800-P4-M), Version 12.1(2)
Copyright (c) 1986-2002 by Cisco Systems, Inc.
advertisement version: 2
Duplex: half
-------------------------
Device ID: lab-as5300-1
Entry address(es):
IP address: 172.19.169.87
.
.
.
Switch#
Table 2-17 describes the fields that are shown in the example.
Related Commands
show class-map
To display class map information, use the show class-map command.
show class-map class_name
Syntax Description
class_name |
Name of the class map. |
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(8a)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
12.2(25)SG |
Displays results from the full flow option. |
Examples
This example shows how to display class map information for all class maps:
Switch# show class-map
Class Map match-any class-default (id 0)
Match any
Class Map match-any class-simple (id 2)
Match any
Class Map match-all ipp5 (id 1)
Match ip precedence 5
Class Map match-all agg-2 (id 3)
Switch#
This example shows how to display class map information for a specific class map:
Switch# show class-map ipp5
Class Map match-all ipp5 (id 1)
Match ip precedence 5
Switch#
Assume there are two active flows as shown below on Fast Ethernet interface 6/1:
SrcIp DstIp IpProt SrcL4Port DstL4Port
--------------------------------------------------------
192.168.10.10 192.168.20.20 20 6789 81
192.168.10.10 192.168.20.20 20 6789 21
With following configuration, each flow will be policed to a 1000000 bps with an allowed 9000-byte burst value.
Note If you use the match flow ip source-address|destination-address command, these two flows are consolidated into one flow and they have the same source and destination address.
Switch# config terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# class-map c1
Switch(config-cmap)# match flow ip source-address ip destination-address ip protocol l4 source-port l4 destination-port
Switch(config-cmap)# exit
Switch(config)# policy-map p1
Switch(config-pmap)# class c1
Switch(config-pmap-c)# police 1000000 9000
Switch(config-pmap-c)# exit
Switch(config-pmap)# exit
Switch(config)# interface fastEthernet 6/1
Switch(config-if)# service-policy input p1
Switch(config-if)# end
Switch# write memory
Switch# show policy-map interface
FastEthernet6/1
class-map c1
match flow ip source-address ip destination-address ip protocol l4 source-port l4 destination-port
!
policy-map p1
class c1
police 1000000 bps 9000 byte conform-action transmit exceed-action drop
!
interface FastEthernet 6/1
service-policy input p1
Switch# show class-map c1
Class Map match-all c1 (id 2)
Match flow ip source-address ip destination-address ip protocol l4 source-port l4 destination-port
Switch#
Related Commands
show diagnostic content
To display test information about the test ID, test attributes, and supported coverage test levels for each test and for all modules, use the show diagnostic content command.
show diagnostic content module {all | num}
Syntax Description
all |
Displays all the modules on the chassis. |
num |
Module number. |
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
|
|
---|---|
12.2(20)EWA |
Support for this command was introduced on the Catalyst 4500 series switch. |
Examples
This example shows how to display the test suite, monitoring interval, and test attributes for all the modules of the chassis:
Switch# show diagnostic content module all
module 1:
Diagnostics test suite attributes:
B/* - Basic ondemand test / NA
P/V/* - Per port test / Per device test / NA
D/N/* - Disruptive test / Non-disruptive test / NA
S/* - Only applicable to standby unit / NA
X/* - Not a health monitoring test / NA
F/* - Fixed monitoring interval test / NA
E/* - Always enabled monitoring test / NA
A/I - Monitoring is active / Monitoring is inactive
m/* - Mandatory bootup test, can't be bypassed / NA
o/* - Ongoing test, always active / NA
Testing Interval
ID Test Name Attributes (day hh:mm:ss.ms)
==== ========================================== ============ =================
1) supervisor-bootup -----------------------> **D****I** not configured
2) packet-memory-bootup --------------------> **D****I** not configured
3) packet-memory-ongoing -------------------> **N****I*o not configured
module 6:
Diagnostics test suite attributes:
B/* - Basic ondemand test / NA
P/V/* - Per port test / Per device test / NA
D/N/* - Disruptive test / Non-disruptive test / NA
S/* - Only applicable to standby unit / NA
X/* - Not a health monitoring test / NA
F/* - Fixed monitoring interval test / NA
E/* - Always enabled monitoring test / NA
A/I - Monitoring is active / Monitoring is inactive
m/* - Mandatory bootup test, can't be bypassed / NA
o/* - Ongoing test, always active / NA
Testing Interval
ID Test Name Attributes (day hh:mm:ss.ms)
==== ========================================== ============ =================
1) linecard-online-diag --------------------> **D****I** not configured
Switch#
Related Commands
|
|
---|---|
Displays the module-based diagnostic test results. |
|
Displays the results of the bootup packet memory test. |
|
Displays the results from the ongoing packet memory test. |
show diagnostic result module
To display the module-based diagnostic test results, use the show diagnostic result module command.
show diagnostic result module [slot-num | all] [test [test-id | test-id-range | all]] [detail]
Syntax Description
Defaults
A summary of the test results for all modules in the chassis is displayed.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.2(18)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Examples
This example shows how to display the summary results for all modules in the chassis:
Switch# show diagnostic result module
Current bootup diagnostic level: minimal
module 1:
Overall diagnostic result: PASS
Diagnostic level at card bootup: bypass
Test results: (. = Pass, F = Fail, U = Untested)
1) supervisor-bootup -----------------------> U
2) packet-memory-bootup --------------------> U
3) packet-memory-ongoing -------------------> U
module 4:
Overall diagnostic result: PASS
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
1) linecard-online-diag --------------------> .
module 5:
Overall diagnostic result: PASS
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
1) linecard-online-diag --------------------> .
module 6:
Overall diagnostic result: PASS
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
1) linecard-online-diag --------------------> .
This example shows how to display the online diagnostics for module 1:
Switch# show diagnostic result module 1 detail
Current bootup diagnostic level: minimal
module 1:
Overall diagnostic result: PASS
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
___________________________________________________________________________
1) supervisor-bootup -----------------------> .
Error code --------------------------> 0 (DIAG_SUCCESS)
Total run count ---------------------> 0
Last test execution time ------------> n/a
First test failure time -------------> n/a
Last test failure time --------------> n/a
Last test pass time -----------------> n/a
Total failure count -----------------> 0
Consecutive failure count -----------> 0
Power-On-Self-Test Results for ACTIVE Supervisor
Power-on-self-test for Module 1: WS-X4014
Port/Test Status: (. = Pass, F = Fail)
Reset Reason: PowerUp Software/User
Port Traffic: L2 Serdes Loopback ...
0: . 1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: . 9: . 10: . 11: .
12: . 13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: .
24: . 25: . 26: . 27: . 28: . 29: . 30: . 31: .
Port Traffic: L2 Asic Loopback ...
0: . 1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: . 9: . 10: . 11: .
12: . 13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: .
24: . 25: . 26: . 27: . 28: . 29: . 30: . 31: .
Port Traffic: L3 Asic Loopback ...
0: . 1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: . 9: . 10: . 11: .
12: . 13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: .
24: . 25: . 26: . 27: . 28: . 29: . 30: . 31: . au: .
Switch Subsystem Memory ...
1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: . 9: . 10: . 11: . 12: .
13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: . 24: .
25: . 26: . 27: . 28: . 29: . 30: . 31: . 32: . 33: . 34: . 35: . 36: .
37: . 38: . 39: . 40: . 41: . 42: . 43: . 44: . 45: . 46: . 47: . 48: .
49: . 50: . 51: . 52: . 53: . 54: .
Module 1 Passed
___________________________________________________________________________
2) packet-memory-bootup --------------------> .
Error code --------------------------> 0 (DIAG_SUCCESS)
Total run count ---------------------> 0
Last test execution time ------------> n/a
First test failure time -------------> n/a
Last test failure time --------------> n/a
Last test pass time -----------------> n/a
Total failure count -----------------> 0
Consecutive failure count -----------> 0
packet buffers on free list: 64557 bad: 0 used for ongoing tests: 979
Number of errors found: 0
Cells with hard errors (failed two or more tests): 0
Cells with soft errors (failed one test, includes hard): 0
Suspect bad cells (uses a block that tested bad): 0
total buffers: 65536
bad buffers: 0 (0.0%)
good buffers: 65536 (100.0%)
Bootup test results:1
No errors.
___________________________________________________________________________
3) packet-memory-ongoing -------------------> U
Error code --------------------------> 0 (DIAG_SUCCESS)
Total run count ---------------------> 0
Last test execution time ------------> n/a
First test failure time -------------> n/a
Last test failure time --------------> n/a
Last test pass time -----------------> n/a
Total failure count -----------------> 0
Consecutive failure count -----------> 0
packet buffers on free list: 64557 bad: 0 used for ongoing tests: 979
Packet memory errors: 0 0
Current alert level: green
Per 5 seconds in the last minute:
0 0 0 0 0 0 0 0 0 0
0 0
Per minute in the last hour:
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
Per hour in the last day:
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 0
Per day in the last 30 days:
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
Direct memory test failures per minute in the last hour:
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
Potential false positives: 0 0
Ignored because of rx errors: 0 0
Ignored because of cdm fifo overrun: 0 0
Ignored because of oir: 0 0
Ignored because isl frames received: 0 0
Ignored during boot: 0 0
Ignored after writing hw stats: 0 0
Ignored on high gigaport: 0
Ongoing diag action mode: Normal
Last 1000 Memory Test Failures:
Last 1000 Packet Memory errors:
First 1000 Packet Memory errors:
___________________________________________________________________________
Switch#
show diagnostic result module test
To display the results of the bootup packet memory test, use the show diagnostic result module test command. The output indicates whether the test passed, failed, or was not run.
show diagnostic result module [N | all] [test test-id] [detail]
Syntax Description
Defaults
Non-detailed results
Command Modes
EXEC mode
Command History
|
|
---|---|
12.2(25)SG |
This command was introduced on the Catalyst 4500 series switch. |
Usage Guidelines
The detail keyword is intended for use by Cisco support personnel when analyzing failures.
Examples
This example shows how to display the results of the bootup packet memory tests:
Switch# show diagnostic result module 6 detail
module 6:
Overall diagnostic result:PASS
Test results:(. = Pass, F = Fail, U = Untested)
___________________________________________________________________________
1) linecard-online-diag --------------------> .
Error code --------------------------> 0 (DIAG_SUCCESS)
Total run count ---------------------> 1
Last test execution time ------------> Jan 21 2001 19:48:30
First test failure time -------------> n/a
Last test failure time --------------> n/a
Last test pass time -----------------> Jan 21 2001 19:48:30
Total failure count -----------------> 0
Consecutive failure count -----------> 0
Slot Ports Card Type Diag Status Diag Details
---- ----- -------------------------------------- ---------------- ------------
6 48 10/100/1000BaseT (RJ45)V, Cisco/IEEE Passed None
Detailed Status
---------------
. = Pass U = Unknown
L = Loopback failure S = Stub failure
I = Ilc failure P = Port failure
E = SEEPROM failure G = GBIC integrity check failure
Ports 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
. . . . . . . . . . . . . . . .
Ports 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
. . . . . . . . . . . . . . . .
Ports 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
. . . . . . . . . . . . . . . .
___________________________________________________________________________
2) online-diag-tdr:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
----------------------------------------------------------------------------
. U U U U U U U U U U U U U U U U U U U U U U U
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
----------------------------------------------------------------------------
U U U U U U U U U U U U U U U U U U U U U U U U
Error code --------------------------> 0 (DIAG_SUCCESS)
Total run count ---------------------> 1
Last test execution time ------------> Jan 22 2001 03:01:54
First test failure time -------------> n/a
Last test failure time --------------> n/a
Last test pass time -----------------> Jan 22 2001 03:01:54
Total failure count -----------------> 0
Consecutive failure count -----------> 0
Detailed Status
---------------
TDR test is in progress on interface Gi6/1
___________________________________________________________________________
Switch#
Related Commands
|
|
---|---|
Runs the specified diagnostic test. |
show diagnostic result module test 2
To display the results of the bootup packet memory test, use the show diagnostic result module test 2 command. The output indicates whether the test passed, failed, or was not run.
show diagnostic result module N test 2 [detail]
Syntax Description
N |
Specifies the module number. |
detail |
(Optional) Specifies the display of detailed information for analysis. |
Defaults
Non-detailed results
Command Modes
EXEC mode
Command History
|
|
---|---|
12.2(18)EW |
This command was introduced on the Catalyst 4500 series switch. |
Usage Guidelines
The detail keyword is intended for use by Cisco support personnel when analyzing failures.
Examples
This example shows how to display the results of the bootup packet memory tests:
Switch# show diagnostic result module 1 test 2
Test results: (. = Pass, F = Fail, U = Untested)
2) packet-memory-bootup ------------> .
This example shows how to display detailed results from the bootup packet memory tests:
Switch# show diagnostic result module 2 test 2 detail
Test results: (. = Pass, F = Fail, U = Untested)
___________________________________________________________________________
2) packet-memory-bootup ------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 0
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
packet buffers on free list: 64557 bad: 0 used for ongoing tests: 979
Number of errors found: 0
Cells with hard errors (failed two or more tests): 0
Cells with soft errors (failed one test, includes hard): 0
Suspect bad cells (uses a block that tested bad): 0
total buffers: 65536
bad buffers: 0 (0.0%)
good buffers: 65536 (100.0%)
Bootup test results:
No errors.
Related Commands
|
|
---|---|
Directs the action of the switch when it detects a packet memory failure. |
|
Displays the results from the ongoing packet memory test. |
show diagnostic result module test 3
To display the results from the ongoing packet memory test, use the show diagnostic result module test 3 command. The output indicates whether the test passed, failed, or was not run.
show diagnostic result module N test 3 [detail]
Syntax Description
N |
Module number. |
detail |
(Optional) Specifies the display of detailed information for analysis. |
Defaults
Non-detailed results
Command Modes
EXEC mode
Command History
|
|
---|---|
12.2(18)EW |
This command was introduced on the Catalyst 4500 series switch. |
Usage Guidelines
The detail keyword is intended for use by Cisco support personnel when analyzing failures.
Examples
This example shows how to display the results from the ongoing packet memory tests:
Switch# show diagnostic result module 1 test 3
Test results: (. = Pass, F = Fail, U = Untested)
3) packet-memory-ongoing -----------> .
This example shows how to display the detailed results from the ongoing packet memory tests:
Switch# show diagnostic result module 1 test 3 detail
Test results: (. = Pass, F = Fail, U = Untested)
___________________________________________________________________________
3) packet-memory-ongoing -----------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 0
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
packet buffers on free list: 64557 bad: 0 used for ongoing tests: 979
Packet memory errors: 0 0
Current alert level: green
Per 5 seconds in the last minute:
0 0 0 0 0 0 0 0 0 0
0 0
Per minute in the last hour:
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
Per hour in the last day:
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 0
Per day in the last 30 days:
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
Direct memory test failures per minute in the last hour:
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
Potential false positives: 0 0
Ignored because of rx errors: 0 0
Ignored because of cdm fifo overrun: 0 0
Ignored because of oir: 0 0
Ignored because isl frames received: 0 0
Ignored during boot: 0 0
Ignored after writing hw stats: 0 0
Ignored on high gigaport: 0
Ongoing diag action mode: Normal
Last 1000 Memory Test Failures: v
Last 1000 Packet Memory errors:
First 1000 Packet Memory errors:
Related Commands
|
|
---|---|
Directs the action of the switch when it detects a packet memory failure. |
|
Displays the results of the bootup packet memory test. |
show dot1x
To display the 802.1X statistics and operational status for the entire switch or for a specified interface, use the show dot1x command.
show dot1x [interface interface-id] | [statistics [interface interface-id]] | [all]
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
If you do not specify an interface, the global parameters and a summary are displayed. If you specify an interface, the details for that interface are displayed.
If you enter the statistics keyword without the interface option, the statistics are displayed for all interfaces. If you enter the statistics keyword with the interface option, the statistics are displayed for the specified interface.
Expressions are case sensitive. For example, if you enter exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed.
The show dot1x command displays the currently assigned reauthentication timer and time remaining before reauthentication, if reauthentication is enabled.
Examples
This example shows how to display the output from the show dot1x command:
Switch# show dot1x
Sysauthcontrol = Disabled
Dot1x Protocol Version = 2
Dot1x Oper Controlled Directions = Both
Dot1x Admin Controlled Directions = Both
Critical Recovery Delay = 500
Critical EAP = Enabled
Switch#
This example shows how to display the 802.1X statistics for a specific port:
Switch# show dot1x interface fastethernet6/1
Dot1x Info for FastEthernet6/1
-----------------------------------
PAE = AUTHENTICATOR
PortControl = AUTO
ControlDirection = Both
HostMode = MULTI_DOMAIN
ReAuthentication = Disabled
QuietPeriod = 60
ServerTimeout = 30
SuppTimeout = 30
ReAuthPeriod = 3600 (Locally configured)
ReAuthMax = 2
MaxReq = 2
TxPeriod = 30
RateLimitPeriod = 0
Dot1x Authenticator Client List
-------------------------------
Domain = DATA
Supplicant = 0000.0000.ab01
Auth SM State = AUTHENTICATED
Auth BEND SM Stat = IDLE
Port Status = AUTHORIZED
Authentication Method = Dot1x
Authorized By = Authentication Server
Vlan Policy = 12
Domain = VOICE
Supplicant = 0060.b057.4687
Auth SM State = AUTHENTICATED
Auth BEND SM Stat = IDLE
Port Status = AUTHORIZED
Authentication Method = Dot1x
Authorized By = Authentication Server
Switch#
Note Table 2-18 provides a partial list of the displayed fields. The remaining fields in the display show internal state information. For a detailed description of these state machines and their settings, refer to the 802.1X specification.
This is an example of output from the show dot1x statistics interface gigabitethernet1/1 command. Table 2-19 describes the fields in the display.
Switch# show dot1x statistics interface gigabitethernet1/1
PortStatistics Parameters for Dot1x
--------------------------------------------
TxReqId = 0 TxReq = 0 TxTotal = 0
RxStart = 0 RxLogoff = 0 RxRespId = 0 RxResp = 0
RxInvalid = 0 RxLenErr = 0 RxTotal= 0
RxVersion = 0 LastRxSrcMac 0000.0000.0000
Switch#
Related Commands
show energywise
Use the show energywise privileged EXEC command to display the EnergyWise settings and status of the entity and the power over Ethernet (PoE) ports.
show energywise [categories | children | domain | events | level [children | current [children] | delta children] | neighbors | recurrences | statistics | usage [children] | version] [ | {begin | exclude | include} expression]
Syntax Description
Command Modes
Privileged EXEC
Command History
|
|
---|---|
12.2(52)SG |
This command was introduced. |
Usage Guidelines
Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear.
Examples
Switch# show energywise
Interface Role Name Usage Lvl Imp Type
--------- ---- ---- ----- --- --- ----
Switch lobby.1 558.0 (W) 10 1 parent
Switch# show energywise children
Interface Role Name Usage Lvl Imp Type
--------- ---- ---- ----- --- --- ----
Switch lobby.1 558.0 (W) 10 1 parent
Gi3/3 interface Gi3.3 0.0 (W) 10 1 child
Gi3/4 interface Gi3.4 0.0 (W) 10 1 child
<output truncated>
Switch# show energywise domain
Name : lobby.1
Domain : area1
Protocol : udp
IP : 10.10.10.2
Port : 43440
Switch# show energywise events
--------------------------------------------
Sequence: 246818 References: 0:1 Errors:
Class: PN_CLASS_QUERY
Action: PN_ACTION_CPQR_POWERNET_QUERY_SET
Reply To: 8.8.8.24:43440
--------------------------------------------
Sequence: 246827 References: 0:1 Errors:
Class: PN_CLASS_DISCOVERY
Action: PN_ACTION_CPQR_POWERNET_DISCOVERY_DISCOVERY_UPDATE
Reply To: 8.8.8.24:43440
--------------------------------------------
Switch# show energywise level
Levels (Watts)
Interface Name 0 1 2 3 4 5 6 7 8 9 10
--------- ---- --------------------------------------------------------------
lobby.1 0.0 558.0 558.0 558.0 558.0 558.0 558.0 558.0 558.0 558.0 558.0
Switch# show energywise level children
Levels (Watts)
Interface Name 0 1 2 3 4 5 6 7 8 9 10
--------- ---- --------------------------------------------------------------
lobby.1 0.0 558.0 558.0 558.0 558.0 558.0 558.0 558.0 558.0 558.0 558.0
Gi1/0/1 Gi1.0.1 0.0 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4
Gi1/0/2 Gi1.0.2 0.0 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4
Gi1/0/3 Gi1.0.3 0.0 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4
Gi1/0/4 Gi1.0.4 0.0 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4
Gi1/0/5 Gi1.0.5 0.0 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4
Gi1/0/1 Gi1.0.1 0.0 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4
<output truncated>
Switch# show energywise level current
Interface Name Level Value
--------- ---- ----- -----
lobby.1 10 558.0 (W)
Switch# show energywise level current children
Interface Name Level Value
--------- ---- ----- -----
lobby.1 10 558.0 (W)
Gi1/0/1 Gi1.0.1 1 15.4 (W)
Gi1/0/2 Gi1.0.2 1 15.4 (W)
Gi1/0/3 Gi1.0.3 1 15.4 (W)
Gi1/0/4 Gi1.0.4 1 15.4 (W)
Gi1/0/5 Gi1.0.5 1 15.4 (W)
<output truncated>
Switch# show energywise level delta
Levels (Watts)
Interface Name 0 1 2 3 4 5 6 7 8 9 10
--------- ---- ------------------------------------------------------------------------
lobby.1 -558.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
Switch# show energywise level delta child
Levels (Watts)
Interface Name 0 1 2 3 4 5 6 7 8 9 10
--------- ---- ------------------------------------------------------------------------
lobby.1 -558.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
Gi1/0/1 Gi1.0.1 0.0 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4
Gi1/0/2 Gi1.0.2 0.0 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4
Gi1/0/3 Gi1.0.3 0.0 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4
Gi1/0/4 Gi1.0.4 0.0 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.4 <output truncated>
Switch# show energywise neighbors
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone
Id Neighbor Name Ip:Port Prot Capability
-- ------------- ------- ---- ----------
1 Switch.A 2.2.2.29:43440 cdp S I
5 Switch.B 2.2.2.22:43440 udp S I
7 Switch.C
Switch# show energywise recurrences
Id Addr Class Action Lvl Cron
-- ---- ----- ------ --- ----
2 Gi1/0/17 QUERY SET 3 minutes: 0 hour: 8 day: * month: * weekday: *
3 Gi1/0/18 QUERY SET 3 minutes: 0 hour: 8 day: * month: * weekday: *
4 Gi1/0/19 QUERY SET 3 minutes: 0 hour: 8 day: * month: * weekday: *
Switch# show energywise statistics
Children: 48 Errors: 2 Drops: 0 Events: 14
Switch# show energywise usage
Interface Name Usage Caliber
--------- ---- _____ _______
lobby.1 558.0 (W) max
Switch# show energywise usage child
Interface Name Usage Caliber
--------- ---- _____ _______
lobby.1 558.0 (W) max
Gi1/0/1 Gi1.0.1 0.0 (W) presumed
Gi1/0/2 Gi1.0.2 0.0 (W) presumed
Gi1/0/3 Gi1.0.3 0.0 (W) presumed
Gi1/0/4 Gi1.0.4 0.0 (W) presumed
Gi1/0/5 Gi1.0.5 0.0 (W) presumed
<output truncated>
Switch# show energywise version
EnergyWise is Enabled
IOS Version: 12.2(52)SG(0.91)
EnergyWise Specification: (t_nrgyz_v122_52_sg_throttle)1.0.14
Related Commands
|
|
---|---|
Enables and configures EnergyWise on the entity. |
|
Configures EnergyWise on the PoE port. |
show environment
To display the environment alarm, operational status, and current reading for the chassis, use the show environment command.
show environment [alarm] | [status [chassis | fantray | powersupply | supervisor]] | [temperature]
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
Examples
This example shows how to display information about the environment alarms, operational status, and current temperature readings for the chassis:
Switch#
show environment
no alarm
Chassis Temperature = 32 degrees Celsius
Chassis Over Temperature Threshold = 75 degrees Celsius
Chassis Critical Temperature Threshold = 95 degrees Celsius
Power Fan
Supply Model No Type Status Sensor
------ --------------- --------- ----------- ------
PS1 PWR-C45-1400AC AC 1400W good good
PS2 none -- -- --
Power Supply Max Min Max Min Absolute
(Nos in Watts) Inline Inline System System Maximum
-------------- ------ ------ ------ ------ --------
PS1 0 0 1360 1360 1400
PS2 -- -- -- -- --
Power supplies needed by system : 1
Chassis Type : WS-C4507R
Supervisor Led Color : Green
Fantray : good
Fantray removal timeout: 240
Power consumed by Fantray : 50 Watts
This example shows how to display information about the environment alarms:
Switch#
show environment alarm
no alarm
Switch#
This example shows how to display information about the power supplies, chassis type, and fan trays:
Switch#
show environment status
Power Fan
Supply Model No Type Status Sensor
------ --------------- --------- ----------- ------
PS1 PWR-C45-1400AC AC 1400W good good
PS2 none -- -- --
Power Supply Max Min Max Min Absolute
(Nos in Watts) Inline Inline System System Maximum
-------------- ------ ------ ------ ------ --------
PS1 0 0 1360 1360 1400
PS2 -- -- -- -- --
Power supplies needed by system : 1
Chassis Type : WS-C4507R
Supervisor Led Color : Green
Fantray : good
Power consumed by Fantray : 50 Watts
Switch#
This example shows how to display information about the chassis:
Switch# show environment status chassis
Chassis Type :WS-C4507R
Switch#
This example shows how to display information about the fan tray:
Switch# show environment status fantray
Fantray : good
Power consumed by Fantray : 50 Watts
Switch#
This example shows how to display information about the power supply:
Switch# show environment status powersupply
Power Fan
Supply Model No Type Status Sensor
------ --------------- --------- ------- ------
PS1 WS-X4008 AC 400W good good
PS2 WS-X4008 AC 400W good good
PS3 none -- -- --
Switch#
This example shows how to display information about the supervisor engine:
Switch# show environment status supervisor
Supervisor Led Color :Green
Switch#
This example shows how to display information about the temperature of the chassis:
Switch#
show environment temperature
Chassis Temperature = 32 degrees Celsius
Chassis Over Temperature Threshold = 75 degrees Celsius
Chassis Critical Temperature Threshold = 95 degrees Celsius
Switch#
show errdisable detect
To display the error disable detection status, use the show errdisable detect command.
show errdisable detect
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(8a)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
12.1(19)EW |
Display includes the status of storm control. |
Examples
This example shows how to display the error disable detection status:
Switch#
show errdisable detect
ErrDisable Reason Detection status
----------------- ----------------
udld Enabled
bpduguard Enabled
security-violatio Enabled
channel-misconfig Disabled
psecure-violation Enabled
vmps Enabled
pagp-flap Enabled
dtp-flap Enabled
link-flap Enabled
l2ptguard Enabled
gbic-invalid Enabled
dhcp-rate-limit Enabled
unicast-flood Enabled
storm-control Enabled
ilpower Enabled
arp-inspection Enabled
Switch#
Related Commands
|
|
---|---|
Enables error-disable detection. |
|
Configures the recovery mechanism variables. |
|
Displays the interface status or a list of interfaces in error-disabled state. |
show errdisable recovery
To display error disable recovery timer information, use the show errdisable recovery command.
show errdisable recovery
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(8a)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
12.1(19)EW |
Display includes the status of storm control. |
Examples
This example shows how to display recovery timer information for error disable:
Switch# show errdisable recovery
ErrDisable Reason Timer Status
----------------- --------------
udld Disabled
bpduguard Disabled
security-violatio Disabled
channel-misconfig Disabled
vmps Disabled
pagp-flap Disabled
dtp-flap Disabled
link-flap Disabled
l2ptguard Disabled
psecure-violation Disabled
gbic-invalid Disabled
dhcp-rate-limit Disabled
unicast-flood Disabled
storm-control Disabled
arp-inspection Disabled
Timer interval:30 seconds
Interfaces that will be enabled at the next timeout:
Interface Errdisable reason Time left(sec)
--------- ----------------- --------------
Fa7/32 arp-inspect 13
Related Commands
|
|
---|---|
Enables error-disable detection. |
|
Configures the recovery mechanism variables. |
|
Displays the interface status or a list of interfaces in error-disabled state. |
show etherchannel
To display EtherChannel information for a channel, use the show etherchannel command.
show etherchannel [channel-group] {port-channel | brief | detail | summary | port | load-balance | protocol}
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(8a)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
12.1(13)EW |
Support for LACP was added to this command. |
Usage Guidelines
If you do not specify a channel group, all channel groups are displayed.
In the output below, the Passive port list field is displayed for Layer 3 port channels only. This field means that the physical interface, which is still not up, is configured to be in the channel group (and indirectly is in the only port channel in the channel group).
Examples
This example shows how to display port-channel information for a specific group:
Switch#
show etherchannel 1 port-channel
Port-channels in the group:
----------------------
Port-channel: Po1
------------
Age of the Port-channel = 02h:35m:26s
Logical slot/port = 10/1 Number of ports in agport = 0
GC = 0x00000000 HotStandBy port = null
Passive port list = Fa5/4 Fa5/5
Port state = Port-channel L3-Ag Ag-Not-Inuse
Ports in the Port-channel:
Index Load Port
-------------------
Switch#
This example shows how to display load-balancing information:
Switch#
show etherchannel load-balance
Source XOR Destination mac address
Switch#
This example shows how to display a summary of information for a specific group:
Switch#
show etherchannel 1 brief
Group state = L3
Ports: 2 Maxports = 8
port-channels: 1 Max port-channels = 1
Switch#
This example shows how to display detailed information for a specific group:
Switch#
show etherchannel 1 detail
Group state = L3
Ports: 2 Maxports = 8
Port-channels: 1 Max Port-channels = 1
Ports in the group:
-------------------
Port: Fa5/4
------------
Port state = EC-Enbld Down Not-in-Bndl Usr-Config
Channel group = 1 Mode = Desirable Gcchange = 0
Port-channel = null GC = 0x00000000 Psudo-agport = Po1
Port indx = 0 Load = 0x00
Flags: S - Device is sending Slow hello. C - Device is in Consistent state.
A - Device is in Auto mode. P - Device learns on physical port.
Timers: H - Hello timer is running. Q - Quit timer is running.
S - Switching timer is running. I - Interface timer is running.
Local information:
Hello Partner PAgP Learning Group
Port Flags State Timers Interval Count Priority Method Ifindex
Fa5/4 d U1/S1 1s 0 128 Any 0
Age of the port in the current state: 02h:33m:14s
Port: Fa5/5
------------
Port state = EC-Enbld Down Not-in-Bndl Usr-Config
Channel group = 1 Mode = Desirable Gcchange = 0
Port-channel = null GC = 0x00000000 Psudo-agport = Po1
Port indx = 0 Load = 0x00
Flags: S - Device is sending Slow hello. C - Device is in Consistent state.
A - Device is in Auto mode. P - Device learns on physical port.
Timers: H - Hello timer is running. Q - Quit timer is running.
S - Switching timer is running. I - Interface timer is running.
Local information:
Hello Partner PAgP Learning Group
Port Flags State Timers Interval Count Priority Method Ifindex
Fa5/5 d U1/S1 1s 0 128 Any 0
Age of the port in the current state: 02h:33m:17s
Port-channels in the group:
----------------------
Port-channel: Po1
------------
Age of the Port-channel = 02h:33m:52s
Logical slot/port = 10/1 Number of ports in agport = 0
GC = 0x00000000 HotStandBy port = null
Passive port list = Fa5/4 Fa5/5
Port state = Port-channel L3-Ag Ag-Not-Inuse
Ports in the Port-channel:
Index Load Port
-------------------
Switch#
This example shows how to display a one-line summary per channel group:
Switch# show etherchannel summary
U-in use I-in port-channel S-suspended D-down i-stand-alone d-default
Group Port-channel Ports
----- ------------ ----------------------------------------------------------
1 Po1(U) Fa5/4(I) Fa5/5(I)
2 Po2(U) Fa5/6(I) Fa5/7(I)
Switch#
This example shows how to display EtherChannel port information for all ports and all groups:
Switch#
show etherchannel port
Channel-group listing:
-----------------------
Group: 1
----------
Ports in the group:
-------------------
Port: Fa5/4
------------
Port state = EC-Enbld Down Not-in-Bndl Usr-Config
Channel group = 1 Mode = Desirable Gcchange = 0
Port-channel = null GC = 0x00000000 Psudo-agport = Po1
Port indx = 0 Load = 0x00
Flags: S - Device is sending Slow hello. C - Device is in Consistent state.
A - Device is in Auto mode. P - Device learns on physical port.
Timers: H - Hello timer is running. Q - Quit timer is running.
S - Switching timer is running. I - Interface timer is running.
Local information:
Hello Partner PAgP Learning Group
Port Flags State Timers Interval Count Priority Method Ifindex
Fa5/4 d U1/S1 1s 0 128 Any 0
Age of the port in the current state: 02h:40m:35s
Port: Fa5/5
------------
Port state = EC-Enbld Down Not-in-Bndl Usr-Config
Channel group = 1 Mode = Desirable Gcchange = 0
Port-channel = null GC = 0x00000000 Psudo-agport = Po1
Port indx = 0 Load = 0x00
Flags: S - Device is sending Slow hello. C - Device is in Consistent state.
A - Device is in Auto mode. P - Device learns on physical port.
Timers: H - Hello timer is running. Q - Quit timer is running.
S - Switching timer is running. I - Interface timer is running.
<...output truncated...>
Switch#
This example shows how to display the protocol enabled:
Switch# show etherchannel protocol
Channel-group listing:
-----------------------
Group: 12
----------
Protocol: PAgP
Group: 24
----------
Protocol: - (Mode ON)
Switch#
Related Commands
|
|
---|---|
Assigns and configures an EtherChannel interface to an EtherChannel group. |
|
Accesses or creates a port-channel interface. |
show flowcontrol
To display the per-interface status and statistics related to flow control, use the show flowcontrol command.
show flowcontrol [module slot | interface interface]
Syntax Description
module slot |
(Optional) Limits the display to interfaces on a specific module. |
interface interface |
(Optional) Displays the status on a specific interface. |
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
Table 2-20 describes the fields in the show flowcontrol command output.
Examples
This example shows how to display the flow control status on all the Gigabit Ethernet interfaces:
Switch# show flowcontrol
Port Send FlowControl Receive FlowControl RxPause TxPause
admin oper admin oper
--------- -------- -------- -------- -------- ------- -------
Te1/1 off off on off 0 0
Te1/2 off off on off 0 0
Gi1/3 off off desired on 0 0
Gi1/4 off off desired on 0 0
Gi1/5 off off desired on 0 0
Gi1/6 off off desired on 0 0
Gi3/1 off off desired off 0 0
Gi3/2 off off desired off 0 0
Gi3/3 off off desired off 0 0
Gi3/4 off off desired off 0 0
Gi3/5 off off desired off 0 0
Gi3/6 off off desired off 0 0
Switch#
This example shows how to display the flow control status on module 1:
Switch# show flowcontrol module 1
Port Send FlowControl Receive FlowControl RxPause TxPause
admin oper admin oper
----- -------- -------- -------- -------- ------- -------
Gi1/1 desired off off off 0 0
Gi1/2 on disagree on on 0 0
Switch#
This example shows how to display the flow control status on Gigabit Ethernet interface 3/4:
Switch# show flowcontrol interface gigabitethernet3/4
Port Send FlowControl Receive FlowControl RxPause TxPause
admin oper admin oper
----- -------- -------- -------- -------- ------- -------
Gi3/4 off off on on 0 0
Switch#
This example shows how to display the flow control status on 10-Gigabit Ethernet interface 1/1:
Switch# show flowcontrol interface tengigabitethernet1/1
Port Send FlowControl Receive FlowControl RxPause TxPause
admin oper admin oper
--------- -------- -------- -------- -------- ------- -------
Te1/1 off off on off 0 0
Switch#
Related Commands
|
|
---|---|
Configures a Gigabit Ethernet interface to send or receive pause frames. |
|
Displays the interface status or a list of interfaces in error-disabled state. |
show hw-module port-group
To display how the X2 holes on a module are grouped, use the show hw-module port-group command.
show hw-module module number port-group
Syntax Description
module |
Specifies a line module. |
number |
Specifies a slot or module number. |
port-group |
Specifies a port-group on a switch. |
Defaults
X2 mode.
Command Modes
Global configuration mode
Command History
|
|
---|---|
12.2(40)SG |
Support for WS-X4606-10GE-E Twin Gigabit convertor introduced. |
Usage Guidelines
When a TwinGig Convertor is enabled or disabled, the number and type of ports on the linecard change dynamically. The terminology must reflect this behavior. In Cisco IOS, 10-Gigabit ports are named TenGigabit and 1-Gigabit ports are named Gigabit. Starting with Cisco IOS Release 12.2(40)SG, to avoid having ports named TenGigabit1/1 and Gigabit1/1, the 10-Gigabit and 1-Gigabit port numbers are independent. The WS-X4606-10GE-E module with six X2 ports are named TenGigabit<slot-num>/<1-6>, and the SFP ports are named Gigabit<slot-num>/<7-18.
In the Supervisor Engine 6-E and Catalyst 4900M chassis, the ports are connected to the switching engine through a stub ASIC. This stub ASIC imposes some limitations on the ports: Gigabit and 10-Gigabit ports cannot be mixed on a single stub ASIC; they must either be all 10-Gigabit (X2), or all Gigabit (TwinGig Converter and SFP). The faceplates of X2 modules show this stub-port grouping, either with an actual physical grouping, or a box drawn around a grouping.
Examples
This example shows to determine how the X2 holes on a module are grouped on a WS-X4606-10GE-E:
Switch# show hw-module module 1 port-group
Module Port-group Active Inactive
-------------------------------------------------------------
1 1 Te1/1-3 Gi1/7-12
1 2 Te1/4-6 Gi1/13-18
Switch#
Related Commands
|
|
---|---|
Selects either Gigabit Ethernet or Ten Gigabit Ethernet interfaces on your module. |
show hw-module uplink
To display the current uplink mode, use the show hw-module uplink command.
show hw-module uplink
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.2(25)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Usage Guidelines
If the active uplink mode is different than configured mode, the output displays the change.
By default, the current (operational) uplink selection is displayed.
Examples
This example shows the output displaying the current (active) uplinks:
Switch# show hw-module uplink
Active uplink configuration is TenGigabitEthernet
This example shows the output for redundant systems in SSO mode if the 10-Gigabit Ethernet uplinks are active, and the Gigabit Ethernet uplinks are selected:
Switch# show hw-module uplink
Active uplink configuration is TenGigabitEthernet
(will be GigabitEthernet after next reload)
A 'redundancy reload shelf' or power-cycle of chassis is required to
apply the new configuration
This example shows the output for redundant systems in RPR mode if the 10-Gigabit Ethernet uplinks are active, and the Gigabit Ethernet uplinks are selected:
Switch# show hw-module uplink
Active uplink configuration is TenGigabitEthernet
(will be GigabitEthernet after next reload)
A reload of active supervisor is required to apply the new configuration.
Related Commands
|
|
---|---|
Selects the 10-Gigabit Ethernet or Gigabit Ethernet uplinks on the Supervisor Engine V-10GE within the W-C4510R chassis. |
show idprom
To display the IDPROMs for the chassis, supervisor engine, module, power supplies, fan trays, clock module, and multiplexer (mux) buffer, use the show idprom command.
show idprom {all | chassis | module [mod] | interface int_name | supervisor | power-supply number | fan-tray}
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
When you enter the show idprom interface command, the output lines for Calibration type and Rx (receive) power measurement may not be displayed for all GBICs.
Examples
This example shows how to display IDPROM information for module 4:
Switch#
show idprom module 4
Module 4 Idprom:
Common Block Signature = 0xABAB
Common Block Version = 1
Common Block Length = 144
Common Block Checksum = 4199
Idprom Size = 256
Block Count = 2
FRU Major Type = 0x4201
FRU Minor Type = 303
OEM String = Cisco Systems, Inc.
Product Number = WS-X4306
Serial Number = 00000135
Part Number = <tbd>
Hardware Revision = 0.2
Manufacturing Bits = 0x0000
Engineering Bits = 0x0000
Snmp OID = 0.0.0.0.0.0.0.0
Power Consumption = 0
RMA Failure Code = 0 0 0 0
Linecard Block Signature = 0x4201
Linecard Block Version = 1
Linecard Block Length = 24
Linecard Block Checksum = 658
Feature Bits = 0x0000000000000000
Card Feature Index = 50
MAC Base = 0010.7bab.9830
MAC Count = 6
Switch#
This example shows how to display IDPROM information for the GBICs on the Gigabit Ethernet interface 1/2:
Switch#
show idprom interface gigabitethernet1/2
GBIC Serial EEPROM Contents:
Common Block:
Identifier = GBIC [0x1]
Extended Id = Not specified/compliant with defined MOD_DEF [0x0]
Connector = SC connector [0x1]
Transceiver
Speed = Not available [0x0]
Media = Not available [0x0]
Technology = Not available [0x0]
Link Length = Not available [0x0]
GE Comp Codes = Not available [0x0]
SONET Comp Codes = Not available [0x0]
Encoding = 8B10B [0x1]
BR, Nominal = 1300000000 MHz
Length(9u) in km = GBIC does not support single mode fibre, or the length
must be determined from the transceiver technology.
Length(9u) = > 25.4 km
Length(50u) = GBIC does not support 50 micron multi-mode fibre, or the
length must be determined from the transceiver technology.
Length(62.5u) = GBIC does not support 62.5 micron multi-mode fibre, or
the length must be determined from transceiver technology.
Length(Copper) = GBIC does not support copper cables, or the length must
be determined from the transceiver technology.
Vendor name = CISCO-FINISAR
Vendor OUI = 36965
Vendor Part No. = FTR-0119-CSC
Vendor Part Rev. = B
Wavelength = Not available
CC_BASE = 0x1A
Extended ID Fields
Options = Loss of Signal implemented TX_FAULT signal implemented TX_DISABLE is implemented and disables the serial output [0x1A]
BR, max = Unspecified
BR, min = Unspecified
Vendor Serial No. = K1273DH
Date code = 030409
Diag monitoring = Implemented
Calibration type = Internal
Rx pwr measuremnt = Optical Modulation Amplitude (OMA)
Address change = Required
CC_EXT = 0xB2
Vendor Specific ID Fields:
20944D30 29 00 02 80 22 33 38 3D C7 67 83 E8 DF 65 6A AF )..."38=Gg^Ch_ej/
20944D40 1A 80 ED 00 00 00 00 00 00 00 00 00 38 23 3C 1B ............8#<.
SEEPROM contents (hex) size 128:
0x0000 01 00 01 00 00 00 00 00 00 00 00 01 0D 00 00 FF ................
0x0010 00 00 00 00 43 49 53 43 4F 2D 46 49 4E 49 53 41 ....CISCO-FINISA
0x0020 52 20 20 20 00 00 90 65 46 54 52 2D 30 31 31 39 R ..^PeFTR-0119
0x0030 2D 43 53 43 20 20 20 20 42 20 20 20 00 00 00 1A -CSC B ....
0x0040 00 1A 00 00 4B 31 32 37 33 44 48 20 20 20 20 20 ....K1273DH
0x0050 20 20 20 20 30 33 30 34 30 39 20 20 64 00 00 B2 030409 d..2
0x0060 29 00 02 80 22 33 38 3D C7 67 83 E8 DF 65 6A AF )..^@"38=Gg^C._ej.
0x0070 1A 80 ED 00 00 00 00 00 00 00 00 00 38 23 3C 1B .^@m.........8#<.
Switch#
This example shows how to display IDPROM information for the 10-Gigabit Ethernet interface 1/1:
Switch#
show idprom interface tengigabitethernet1/1
X2 Serial EEPROM Contents:
Non-Volatile Register (NVR) Fields
X2 MSA Version supported :0xA
NVR Size in bytes :0x100
Number of bytes used :0xD0
Basic Field Address :0xB
Customer Field Address :0x77
Vendor Field Address :0xA7
Extended Vendor Field Address :0x100
Reserved :0x0
Transceiver type :0x2 =X2
Optical connector type :0x1 =SC
Bit encoding :0x1 =NRZ
Normal BitRate in multiple of 1M b/s :0x2848
Protocol Type :0x1 =10GgE
Standards Compliance Codes :
10GbE Code Byte 0 :0x2 =10GBASE-LR
10GbE Code Byte 1 :0x0
SONET/SDH Code Byte 0 :0x0
SONET/SDH Code Byte 1 :0x0
SONET/SDH Code Byte 2 :0x0
SONET/SDH Code Byte 3 :0x0
10GFC Code Byte 0 :0x0
10GFC Code Byte 1 :0x0
10GFC Code Byte 2 :0x0
10GFC Code Byte 3 :0x0
Transmission range in 10m :0x3E8
Fibre Type :
Fibre Type Byte 0 :0x40 =NDSF only
Fibre Type Byte 1 :0x0 =Unspecified
Centre Optical Wavelength in 0.01nm steps - Channel 0 :0x1 0xFF 0xB8
Centre Optical Wavelength in 0.01nm steps - Channel 1 :0x0 0x0 0x0
Centre Optical Wavelength in 0.01nm steps - Channel 2 :0x0 0x0 0x0
Centre Optical Wavelength in 0.01nm steps - Channel 3 :0x0 0x0 0x0
Package Identifier OUI :0xC09820
Transceiver Vendor OUI :0x3400800
Transceiver vendor name :CISCO-OPNEXT,INC
Part number provided by transceiver vendor :TRT5021EN-SMC-W
Revision level of part number provided by vendor :00
Vendor serial number :ONJ08290041
Vendor manufacturing date code :2004072000
Reserved1 : 00 02 02 20 D1 00 00
Basic Field Checksum :0x10
Customer Writable Area :
0x00: 58 32 2D 31 30 47 42 2D 4C 52 20 20 20 20 20 20
0x10: 20 20 20 20 20 4F 4E 4A 30 38 32 39 30 30 34 31
0x20: 31 30 2D 32 30 33 36 2D 30 31 20 20 41 30 31 20
Vendor Specific :
0x00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x30: 00 00 00 00 11 E2 69 A9 2F 95 C6 EE D2 DA B3 FD
0x40: 9A 34 4A 24 CB 00 00 00 00 00 00 00 00 00 EF FC
0x50: F4 AC 1A D7 11 08 01 36 00
Switch#
This example shows how to display IDPROM information for the supervisor engine:
Switch#
show idprom supervisor
Supervisor Idprom:
Common Block Signature = 0xABAB
Common Block Version = 1
Common Block Length = 144
Common Block Checksum = 4153
Idprom Size = 256
Block Count = 2
FRU Major Type = 0x4101
FRU Minor Type = 333
OEM String = Cisco Systems, Inc.
Product Number = WS-X4014
Serial Number = JAB05320CCE
Part Number = 73-6854-04
Part Revision = 05
Manufacturing Deviation String = 0
Hardware Revision = 0.4
Manufacturing Bits = 0x0000
Engineering Bits = 0x0000
Snmp OID = 0.0.0.0.0.0.0.0
Power Consumption = 0
RMA Failure Code = 0 0 0 0
Supervisor Block Signature = 0x4101
Supervisor Block Version = 1
Supervisor Block Length = 24
Supervisor Block Checksum = 548
Feature Bits = 0x0000000000000000
Card Feature Index = 95
MAC Base = 0007.0ee5.2a44
MAC Count = 2
Switch#
This example shows how to display IDPROM information for the chassis:
Switch#
show idprom chassis
Chassis Idprom:
Common Block Signature = 0xABAB
Common Block Version = 1
Common Block Length = 144
Common Block Checksum = 4285
Idprom Size = 256
Block Count = 2
FRU Major Type = 0x4001
FRU Minor Type = 24
OEM String = Cisco Systems, Inc.
Product Number = WS-C4507R
Serial Number = FOX04473737
Part Number = 73-4289-02
Part Revision = 02
Manufacturing Deviation String = 0x00
Hardware Revision = 0.2
Manufacturing Bits = 0x0000
Engineering Bits = 0x0000
Snmp OID = 0.0.0.0.0.0.0.0
Chassis Block Signature = 0x4001
Chassis Block Version = 1
Chassis Block Length = 22
Chassis Block Checksum = 421
Feature Bits = 0x0000000000000000
MAC Base = 0004.dd42.2600
MAC Count = 1024
Switch#
This example shows how to display IDPROM information for power supply 1:
Switch#
show idprom power-supply 1
Power Supply 0 Idprom:
Common Block Signature = 0xABAB
Common Block Version = 1
Common Block Length = 144
Common Block Checksum = 10207
Idprom Size = 256
Block Count = 1
FRU Major Type = 0xAB01
FRU Minor Type = 8224
OEM String = Cisco Systems, Inc.
Product Number = WS-CAC-1440W
Serial Number = ACP05180002
Part Number = 34-XXXX-01
Part Revision = A0
Manufacturing Deviation String =
Hardware Revision = 1.1
Manufacturing Bits = 0x0000
Engineering Bits = 0x3031
Snmp OID = 9.12.3.65535.65535.65535.65535.65535
Power Consumption = -1
RMA Failure Code = 255 255 255 255
Power Supply Block Signature = 0xFFFF
PowerSupply Block Version = 255
PowerSupply Block Length = 255
PowerSupply Block Checksum = 65535
Feature Bits = 0x00000000FFFFFFFF
Current @ 110V = -1
Current @ 220V = -1
StackMIB OID = 65535
Switch#
This example shows how to display IDPROM information for the fan tray:
Switch#
show idprom fan-tray
Fan Tray Idprom :
Common Block Signature = 0xABAB
Common Block Version = 1
Common Block Length = 144
Common Block Checksum = 19781
Idprom Size = 256
Block Count = 1
FRU Major Type = 0x4002
FRU Minor Type = 0
OEM String = "Cisco Systems"
Product Number = WS-X4502-fan
Serial Number =
Part Number =
Part Revision =
Manufacturing Deviation String =
Hardware Revision = 0.1
Manufacturing Bits = 0xFFFF
Engineering Bits = 0xFFFF
Snmp OID = 65535.65535.65535.65535.65535.65535.65535.65535
Power Consumption = -1
RMA Failure Code = 255 255 255 255
Switch#
show interfaces
To display traffic on a specific interface, use the show interfaces command.
show interfaces [{{fastethernet mod/interface-number} | {gigabitethernet mod/interface-number} | {tengigabitethernet mod/interface-number} | {null interface-number} | vlan vlan_id} | status}]
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
The statistics are collected per VLAN for Layer 2 switched packets and Layer 3 switched packets. The statistics are available for both unicast and multicast. The Layer 3 switched packet counts are available for both the ingress and egress directions. The per-VLAN statistics are updated every 5 seconds.
In some cases, the duplex mode that is displayed by the show interfaces command is different than that displayed by the show running-config command. The duplex mode that is displayed in the show interfaces command is the actual duplex mode that the interface is running. The show interfaces command shows the operating mode for an interface, but the show running-config command shows the configured mode for an interface.
If you do not enter any keywords, all counters for all modules are displayed.
Linecards that support auto-MDIX configuration on their copper media ports include: WS-X4124-RJ45, WS-X4148-RJ with hardware revision 3.0 or later, and WS-X4232-GB-RJ with hardware revision 3.0 or later.
Examples
This example shows how to display traffic for Gigabit Ethernet interface 2/5:
Switch# show interfaces gigabitethernet2/5
GigabitEthernet9/5 is up, line protocol is up (connected) (vlan-err-dis)
Hardware is C4k 1000Mb 802.3, address is 0001.64f8.3fa5 (bia 0001.64f8.3fa5)
Internet address is 172.20.20.20/24
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output never, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 1000 bits/sec, 2 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
L2 Switched: ucast: 8199 pkt, 1362060 bytes - mcast: 6980 pkt, 371952 bytes
L3 in Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes mcast
L3 out Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes
300114 packets input, 27301436 bytes, 0 no buffer
Received 43458 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
15181 packets output, 1955836 bytes, 0 underruns
0 output errors, 0 collisions, 3 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Switch#
This example shows how to display traffic for 10-Gigabit Ethernet interface 1/1:
Switch# show interfaces tengigabitethernet1/1
Name: Tengigabitethernet1/1
Switchport: Enabled
Administrative Mode: private-vlan promiscuous trunk
Operational Mode: private-vlan promiscuous (suspended member of bundle Po1)
Administrative Trunking Encapsulation: negotiate
Operational Trunking Encapsulation: native
Negotiation of Trunking: Off
Access Mode VLAN: none
Trunking Native Mode VLAN: none
Administrative Native VLAN tagging: enabled
Voice VLAN: none
Administrative private-vlan host-association: none
Administrative private-vlan mapping: 202 (VLAN0202) 303 (VLAN0303) 304 (VLAN0304)
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk
Native VLAN tagging: enabled
Administrative private-vlan trunk encapsulation: 802.1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk private VLANs: none
Administrative private-vlan mapping trunk: New 202 (VLAN0202) 303 (VLAN0303) 304 (VLAN0304) 204 (VLAN0204) 305 (VLAN0305) 306 (VLAN0306)
Operational private-vlan: 202 (VLAN0202) 303 (VLAN0303) 304 (VLAN0304)
Trunking VLANs Enabled: ALL
Pruning VLANs Enabled: 2-1001
Capture Mode Disabled
Capture VLANs Allowed: ALL
Switch#
This example shows how to verify the status of auto-MDIX on an RJ-45 port:
Note You can verify the configuration setting and the operational state of auto-MDIX on the interface by entering the show interfaces EXEC command. This field is applicable and appears only on the
show interfaces command output for 10/100/1000BaseT RJ-45 copper ports on supported linecards including WS-X4124-RJ45, WS-X4148-RJ with hardware revision 3.0 or later, and WS-X4232-GB-RJ with hardware revision 3.0 or later.
FastEthernet6/3 is up, line protocol is up (connected)
Hardware is Fast Ethernet Port, address is 0003.6ba8.ee68 (bia 0003.6ba8.ee68)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, link type is auto, media type is 10/100BaseTX
input flow-control is unsupported output flow-control is unsupported
Auto-MDIX on (operational: on)
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
157082 packets output, 13418032 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
1 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Switch#
This example shows how to display status information for Gigabit Ethernet interface 1/2:
Switch# show interfaces gigabitethernet1/2 status
Port Name Status Vlan Duplex Speed Type
Gi1/2 notconnect 1 auto 1000 1000-XWDM-RXONLY
Switch#
This example shows how to display status information for the interfaces on the supervisor engine:
Switch# show interfaces status
Port Name Status Vlan Duplex Speed Type
Te1/1 connected 1 full 10G 10GBase-LR
Te1/2 connected 1 full 10G 10GBase-LR
Switch#
show interfaces capabilities
To display the interface capabilities for an interface or for all the interfaces on a switch, use the
show interfaces capabilities command.
show interfaces capabilities [{module mod}]
show interfaces [interface interface-number] capabilities
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
The interface-number argument designates the module and port number. Valid values for interface-number depend on the chassis and module used. For example, if you have a 48-port 10/100-Mbps Fast Ethernet RJ-21 (telco connector) switching module installed in a Catalyst 4507 chassis, valid values for the slot number are from 2 to 13 and valid values for the port number are 1 to 48.
Linecards that support auto-MDIX configuration on their copper media ports include: WS-X4124-RJ45, WS-X4148-RJ with hardware revision 3.0 or higher, and WS-X4232-GB-RJ with hardware revision 3.0 or higher.
Examples
This example shows how to display the interface capabilities for a module:
Switch# show interfaces capabilities module 1
GigabitEthernet1/1
Model: WS-X4516-Gbic
Type: Unsupported GBIC
Speed: 1000
Duplex: full
Trunk encap. type: 802.1Q,ISL
Trunk mode: on,off,desirable,nonegotiate
Channel: yes
Broadcast suppression:percentage(0-100), hw
Flowcontrol: rx-(off,on,desired),tx-(off,on,desired)
VLAN Membership: static, dynamic
Fast Start: yes
Queuing: rx-(N/A), tx-(4q1t, Sharing/Shaping)
CoS rewrite: yes
ToS rewrite: yes
Inline power: no
SPAN: source/destination
UDLD yes
Link Debounce: no
Link Debounce Time: no
Port Security yes
Dot1x yes
GigabitEthernet1/2
Model: WS-X4516-Gbic
Type: Unsupported GBIC
Speed: 1000
Duplex: full
Trunk encap. type: 802.1Q,ISL
Trunk mode: on,off,desirable,nonegotiate
Channel: yes
Broadcast suppression:percentage(0-100), hw
Flowcontrol: rx-(off,on,desired),tx-(off,on,desired)
VLAN Membership: static, dynamic
Fast Start: yes
Queuing: rx-(N/A), tx-(4q1t, Sharing/Shaping)
CoS rewrite: yes
ToS rewrite: yes
Inline power: no
SPAN: source/destination
UDLD yes
Link Debounce: no
Link Debounce Time: no
Port Security yes
Dot1x yes
Switch#
This example shows how to display the interface capabilities for the 10-Gigabit Ethernet interface 1/1:
Switch# show interfaces tengigabitethernet1/1 capabilities
TenGigabitEthernet1/1
Model: WS-X4517-X2
Type: 10GBase-LR
Speed: 10000
Duplex: full
Trunk encap. type: 802.1Q,ISL
Trunk mode: on,off,desirable,nonegotiate
Channel: yes
Broadcast suppression: percentage(0-100), hw
Flowcontrol: rx-(off,on),tx-(off,on)
VLAN Membership: static, dynamic
Fast Start: yes
Queuing: rx-(N/A), tx-(1p3q1t, Sharing/Shaping)
CoS rewrite: yes
ToS rewrite: yes
Inline power: no
SPAN: source/destination
UDLD: yes
Link Debounce: no
Link Debounce Time: no
Port Security: yes
Dot1x: yes
Maximum MTU: 9198 bytes (Jumbo Frames)
Multiple Media Types: no
Diagnostic Monitoring: N/A
Switch#
This example shows how to display the interface capabilities for Gigabit Ethernet interface 1/1:
Switch# show interfaces gigabitethernet1/1 capabilities
GigabitEthernet1/1
Model: WS-X4014-Gbic
Type: No Gbic
Speed: 1000
Duplex: full
Trunk encap. type: 802.1Q,ISL
Trunk mode: on,off,desirable,nonegotiate
Channel: yes
Broadcast suppression:percentage(0-100), hw
Flowcontrol: rx-(off,on,desired),tx-(off,on,desired)
VLAN Membership: static, dynamic
Fast Start: yes
Queuing: rx-(N/A), tx-(4q1t, Sharing/Shaping)
CoS rewrite: yes
ToS rewrite: yes
Inline power: no
SPAN: source/destination
UDLD: yes
Link Debounce: no
Link Debounce Time: no
Port Security: yes
Dot1x: yes
MTU Supported: jumbo frames, baby giants
Switch#
This example shows how to display the interface capabilities for Fast Ethernet interface 3/1:
Switch# show interfaces fastethernet3/1 capabilities
FastEthernet3/1
Model: WS-X4148-RJ-RJ-45
Type: 10/100BaseTX
Speed: 10,100,auto
Duplex: half,full,auto
Trunk encap. type: 802.1Q,ISL
Trunk mode: on,off,desirable,nonegotiate
Channel: yes
Broadcast suppression:percentage(0-100), sw
Flowcontrol: rx-(none),tx-(none)
VLAN Membership: static, dynamic
Fast Start: yes
Queuing: rx-(N/A), tx-(4q1t, Shaping)
CoS rewrite: yes
ToS rewrite: yes
Inline power: no
SPAN: source/destination
UDLD: yes
Link Debounce: no
Link Debounce Time: no
Port Security: yes
Dot1x: yes
MTU Supported: no jumbo frames, baby giants
Switch#
This example shows how to verify that the auto-MDIX configuration is supported on a port:
Switch# show interfaces fastethernet6/3 capabilities
FastEthernet6/3
Model: WS-X4232-GB-RJ-RJ-45
Type: 10/100BaseTX
Speed: 10,100,auto
Duplex: half,full,auto
Auto-MDIX yes
Trunk encap. type: 802.1Q,ISL
Trunk mode: on,off,desirable,nonegotiate
Channel: yes
Broadcast suppression: percentage(0-100), hw
Flowcontrol: rx-(none),tx-(none)
VLAN Membership: static, dynamic
Fast Start: yes
Queuing: rx-(N/A), tx-(1p3q1t, Sharing/Shaping)
CoS rewrite: yes
ToS rewrite: yes
Inline power: no
SPAN: source/destination
UDLD: yes
Link Debounce: no
Link Debounce Time: no
Port Security: yes
Dot1x: yes
Maximum MTU: 1552 bytes (Baby Giants)
Multiple Media Types: no
Diagnostic Monitoring: N/A
Switch#
Related Commands
|
|
---|---|
Displays the traffic on the physical interface. |
show interfaces counters
To display the traffic on the physical interface, use the show interfaces counters command.
show interfaces counters [all | detail | errors | storm-control | trunk] [module mod]
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
If you do not enter any keywords, all the counters for all modules are displayed.
The display for the storm-control keyword includes the suppressed multicast bytes.
Examples
This example shows how to display the error counters for a specific module:
Switch#
show interfaces counters errors module 1
Port Align-Err FCS-Err Xmit-Err Rcv-Err UnderSize
Gi1/1 0 0 0 0 0
Gi1/2 0 0 0 0 0
Port Single-Col Multi-Col Late-Col Excess-Col Carri-Sen Runts Giants
Gi1/1 0 0 0 0 0 0 0
Gi1/2 0 0 0 0 0 0 0
Switch#
This example shows how to display the traffic that is seen by a specific module:
Switch#
show interfaces counters module 1
Port InOctets InUcastPkts InMcastPkts InBcastPkts
Gi1/1 0 0 0 0
Gi1/2 0 0 0 0
Port OutOctets OutUcastPkts OutMcastPkts OutBcastPkts
Gi1/1 0 0 0 0
Gi1/2 0 0 0 0
Switch#
This example shows how to display the trunk counters for a specific module:
Switch#
show interfaces counters trunk module 1
Port TrunkFramesTx TrunkFramesRx WrongEncap
Gi1/1 0 0 0
Gi1/2 0 0 0
Switch#
This example shows how to display the number of packets that are discarded due to suppression:
Switch#
show interfaces counters storm-control
Multicast Suppression : Enabled
Port BcastSuppLevel TotalSuppressionDiscards
Fa5/35 10.00% 6278550
Switch#
Related Commands
|
|
---|---|
Displays the interface capabilities for an interface or for all the interfaces on a switch. |
show interfaces description
To display a description and status of an interface, use the show interfaces description command.
show interfaces [interface] description
Syntax Description
interface |
(Optional) Type of interface. |
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(8a)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Examples
This example shows how to display information for all interfaces:
Switch# show interfaces description
Interface Status Protocol Description
PO0/0 admin down down First interface
PO0/1 admin down down
Gi1/1 up up GigE to server farm
Switch#
Related Commands
|
|
---|---|
description (refer to Cisco IOS documentation) |
Includes a specific description about the digital signal processor (DSP) interface. |
show interfaces link
To display how long a cable has been disconnected from an interface, use the show interfaces link command:
show interfaces link [module mod_num]
Syntax Description
module mod_num |
(Optional) Limits the display to interfaces on a module. |
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.2(18)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Usage Guidelines
If the interface state is up, the command displays 0:00. If the interface state is down, the time (in hours, minutes, and seconds) is displayed.
Examples
This example shows how to display active link-level information:
Switch# show interfaces link
Port Name Down Time
Gi1/1 00:00:00
Gi1/2 00:00:00
Gi3/1 00:00:00
Gi3/2 00:00:00
Fa4/1 00:00:00
Fa4/2 00:00:00
Fa4/3 00:00:00
Fa4/4 00:00:00
This example shows how to display inactive link-level information:
Switch# show interfaces link
Port Name Down Time
Gi3/4 1 minute 28 secs
Gi3/5 1 minute 28 secs
Gi3/6 1 minute 28 secs
Gi4/1 1 minute 28 secs
In this example, the cable has been disconnected from the port for 1 minute and 28 seconds.
show interfaces mtu
To display the maximum transmission unit (MTU) size of all the physical interfaces and SVIs on the switch, use the show interfaces mtu command.
show interfaces mtu [module mod]
Syntax Description
module mod |
(Optional) Limits the display to interfaces on a specific module. |
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
|
|
12.1(13)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Examples
This example shows how to display the MTU size for all interfaces on module 1:
Switch>
show interfaces mtu module 1
Port Name MTU
Gi1/1 1500
Gi1/2 1500
Switch>
Related Commands
|
|
---|---|
Enables jumbo frames on an interface by adjusting the maximum size of a packet or maximum transmission unit (MTU). |
show interfaces private-vlan mapping
To display PVLAN mapping information for VLAN SVIs, use the show interfaces private-vlan mapping command.
show interfaces private-vlan mapping [active]
Syntax Description
active |
(Optional) Displays active interfaces only. |
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(8a)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Usage Guidelines
This command displays SVI information only.
Examples
This example shows how to display PVLAN mapping information:
Switch# show interfaces private-vlan mapping
Interface Secondary VLAN Type
--------- -------------- -----------------
vlan2 301 isolated
vlan2 302 isolated
Switch#
Related Commands
show interfaces status
To display the interface status or a list of interfaces in error-disabled state, use the show interfaces status command.
show interfaces status [err-disabled | inactive ] [module {module}]
Syntax Description
err-disabled |
(Optional) Displays interfaces in error-disabled state. |
inactive |
(Optional) Displays interfaces in inactive state. |
module module |
(Optional) Displays interfaces on a specific module. |
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
When at least one VLAN on a port is error-disabled the output for the show interfaces status command will display vl-err-dis in the VLAN column.
Examples
This example shows how to display the status of all interfaces:
Switch#
show interfaces status
Port Name Status Vlan Duplex Speed Type
Te1/1 connected 1 full 10G 10GBase-LR
Te1/2 connected vl-err-dis full 10G 10GBase-LR
Switch#
This example shows how to display the status of interfaces in an error-disabled state:
Switch#
show interfaces status err-disabled
Port Name Status Reason Err-Disabled VLANs
---- ---- ------ ------- -------------------
Fa9/4 notconnect link-flap
Fa9/5 err-disabled psecure_violation 3-5
Fa9/6 connected psecure_violation 10,15
Switch#
This example shows how to display the Gigabit Ethernet interfaces on a WS-X4606-10GE-E switch using the TwinGig Convertor:
Switch# show interfaces status module 1
Port Name Status Vlan Duplex Speed Type
Te1/1 inactive 1 full 10G No X2
Te1/2 inactive 1 full 10G No X2
Te1/3 inactive 1 full 10G No X2
Te1/4 notconnect 1 full 10G No X2
Te1/5 notconnect 1 full 10G No X2
Te1/6 notconnect 1 full 10G No X2
Gi1/7 notconnect 1 full 1000 No Gbic
Gi1/8 notconnect 1 full 1000 No Gbic
Gi1/9 notconnect 1 full 1000 No Gbic
Gi1/10 notconnect 1 full 1000 No Gbic
Gi1/11 notconnect 1 full 1000 No Gbic
Gi1/12 notconnect 1 full 1000 No Gbic
Gi1/13 inactive 1 full 1000 No Gbic
Gi1/14 inactive 1 full 1000 No Gbic
Gi1/15 inactive 1 full 1000 No Gbic
Gi1/16 inactive 1 full 1000 No Gbic
Gi1/17 inactive 1 full 1000 No Gbic
Gi1/18 inactive 1 full 1000 No Gbic
Switch#
Related Commands
|
|
---|---|
Enables error-disable detection. |
|
Selects either Gigabit Ethernet or Ten Gigabit Ethernet interfaces on your module. |
|
Displays error-disable recovery timer information. |
show interfaces switchport
To display the administrative and operational status of a switching (nonrouting) port, use the show interfaces switchport command.
show interfaces [interface-id] switchport [module mod]
Syntax Description
interface-id |
(Optional) Interface ID for the physical port. |
module mod |
(Optional) Limits the display to interfaces on the specified module; valid values are from 1 to 6. |
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
Examples
This example shows how to display switch-port information using the begin output modifier:
Switch#
show interfaces switchport | include VLAN
Name: Fa5/6
Access Mode VLAN: 200 (VLAN0200)
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Pruning VLANs Enabled: ALL
Switch#
This example shows how to display switch-port information for module 1:
Switch#
show interfaces switchport module 1
Name:Gi1/1
Switchport:Enabled
Administrative Mode:dynamic auto
Operational Mode:down
Administrative Trunking Encapsulation:negotiate
Negotiation of Trunking:On
Access Mode VLAN:1 (default)
Trunking Native Mode VLAN:1 (default)
Administrative private-vlan host-association:none
Administrative private-vlan mapping:none
Operational private-vlan:none
Trunking VLANs Enabled:ALL
Pruning VLANs Enabled:2-1001
Name:Gi1/2
Switchport:Enabled
Administrative Mode:dynamic auto
Operational Mode:down
Administrative Trunking Encapsulation:negotiate
Negotiation of Trunking:On
Access Mode VLAN:1 (default)
Trunking Native Mode VLAN:1 (default)
Administrative private-vlan host-association:none
Administrative private-vlan mapping:none
Operational private-vlan:none
Trunking VLANs Enabled:ALL
Pruning VLANs Enabled:2-1001
Switch#
This example shows how to display the status of native VLAN tagging on the port:
Switch#
show interfaces f3/1 switchport
show interface f3/1 switchport
Name: Fa3/1
Switchport: Enabled
Administrative Mode: private-vlan trunk promiscuous
Operational Mode: private-vlan trunk promiscuous
Administrative Trunking Encapsulation: negotiate
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: On
Access Mode VLAN: 1 (default)
Trunking Native Mode VLAN: 1 (default)
Administrative Native VLAN tagging: enabled
Voice VLAN: none
Administrative private-vlan host-association: none
Administrative private-vlan mapping: none
Administrative private-vlan trunk native VLAN: 1
Administrative private-vlan trunk Native VLAN tagging: enabled
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: 1
Administrative private-vlan trunk associations: none
Administrative private-vlan trunk mappings:
10 (VLAN0010) 100 (VLAN0100)
Operational private-vlan:
10 (VLAN0010) 100 (VLAN0100)
Trunking VLANs Enabled: ALL
Pruning VLANs Enabled: 2-1001
Capture Mode Disabled
Capture VLANs Allowed: ALL
Unknown unicast blocked: disabled
Unknown multicast blocked: disabled
Appliance trust: none
Switch#
Related Commands
|
|
---|---|
Displays the interface capabilities for an interface or for all the interfaces on a switch. |
|
Displays the traffic on the physical interface. |
show interfaces transceiver
To display diagnostic-monitoring data for all interfaces that have transceivers installed, use the show interfaces transceiver command.
show interfaces {{[int_name] transceiver {[detail]} | {transceiver [module mod] | detail [module mod]}}
Syntax Description
Defaults
The noninterface-specific versions of the show interfaces transceiver command are enabled by default.
The interface-specific versions of these commands are enabled by default if the specified interface has a transceiver (GBIC or SFP) that is configured for diagnostic monitoring, and the transceiver is in a module that supports diagnostic monitoring.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(20)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
12.2(18)EW |
Support for the calibration keyword was withdrawn. |
Usage Guidelines
The show interfaces transceiver command provides useful information under the following conditions:
•At least one transceiver is installed on a chassis that is configured for diagnostic monitoring.
•The transceiver is in a module that supports diagnostic monitoring.
If you notice that the alarm and warning flags have been set on a transceiver, reenter the command to confirm.
Examples
This example shows how to display diagnostic monitoring data for all interfaces with transceivers installed on the switch:
Switch# show interfaces transceiver
If device is externally calibrated, only calibrated values are printed.
++ : high alarm, + : high warning, - : low warning, -- : low alarm.
NA or N/A: not applicable, Tx: transmit, Rx: receive.
mA: milliamperes, dBm: decibels (milliwatts).
Optical Optical
Temperature Voltage Current Tx Power Rx Power
Port (Celsius) (Volts) (mA) (dBm) (dBm)
------- ----------- ------- -------- -------- --------
Gi1/1 48.1 3.30 0.0 8.1 ++ N/A
Gi1/2 33.0 3.30 1.8 -10.0 -36.9
Gi2/1 43.7 5.03 50.6 + -16.7 -- N/A
Gi2/2 39.2 5.02 25.7 0.8 N/A
Switch#
Note The value for the Optical Tx Power (in dBm) equals ten times log (Tx Power in mW). If the Tx Power value is 3 mW, then the Optical Tx Power value equals 10 * log (3), which equals 10 * .477 or 4.77 dBm. The Optical Rx Power value behaves similarly. If the Tx Power or the Rx Power is zero, then its dBm value is undefined and is shown as N/A (not applicable).
This example shows how to display detailed diagnostic monitoring data, including calibrated values, alarm and warning thresholds, A2D readouts, and alarm and warning flags. The A2D readouts are reported separately in parentheses only if they differ from the calibrated values:
Switch# show interfaces transceiver detail
mA: milliamperes, dBm: decibels (milliwatts), NA or N/A: not applicable.
++ : high alarm, + : high warning, - : low warning, -- : low alarm.
A2D readouts (if they differ), are reported in parentheses.
The threshold values are calibrated.
High Alarm High Warn Low Warn Low Alarm
Temperature Threshold Threshold Threshold Threshold
Port (Celsius) (Celsius) (Celsius) (Celsius) (Celsius)
------- ------------------ ---------- --------- --------- ---------
Gi1/1 48.1 100.0 100.0 0.0 0.0
Gi1/2 34.9 100.0 100.0 0.0 0.0
Gi2/1 43.5 70.0 60.0 5.0 0.0
Gi2/2 39.1 70.0 60.0 5.0 0.0
High Alarm High Warn Low Warn Low Alarm
Voltage Threshold Threshold Threshold Threshold
Port (Volts) (Volts) (Volts) (Volts) (Volts)
------- --------------- ---------- --------- --------- ---------
Gi1/1 3.30 6.50 6.50 N/A N/A
Gi1/2 3.30 6.50 6.50 N/A N/A
Gi2/1 5.03 5.50 5.25 4.75 4.50
Gi2/2 5.02 5.50 5.25 4.75 4.50
High Alarm High Warn Low Warn Low Alarm
Current Threshold Threshold Threshold Threshold
Port (milliamperes) (mA) (mA) (mA) (mA)
------- ----------------- ---------- --------- --------- ---------
Gi1/1 0.0 130.0 130.0 N/A N/A
Gi1/2 1.7 130.0 130.0 N/A N/A
Gi2/1 50.6 + 60.0 40.0 10.0 5.0
Gi2/2 25.8 60.0 40.0 10.0 5.0
Optical High Alarm High Warn Low Warn Low Alarm
Transmit Power Threshold Threshold Threshold Threshold
Port (dBm) (dBm) (dBm) (dBm) (dBm)
------- ----------------- ---------- --------- --------- ---------
Gi1/1 8.1 ++ 8.1 8.1 N/A N/A
Gi1/2 -9.8 8.1 8.1 N/A N/A
Gi2/1 -16.7 (-13.0) -- 3.4 3.2 -0.3 -0.5
Gi2/2 0.8 ( 5.1) 3.4 3.2 -0.3 -0.5
Optical High Alarm High Warn Low Warn Low Alarm
Receive Power Threshold Threshold Threshold Threshold
Port (dBm) (dBm) (dBm) (dBm) (dBm)
------- ----------------- ---------- --------- --------- ---------
Gi1/1 N/A 8.1 8.1 N/A N/A
Gi1/2 -30.9 8.1 8.1 N/A N/A
Gi2/1 N/A (-28.5) 5.9 -6.7 -28.5 -28.5
Gi2/2 N/A (-19.5) 5.9 -6.7 -28.5 -28.5
Switch#
This example shows how to display the monitoring data for the interfaces that have transceivers installed on module 2:
Switch# show interfaces transceiver module 2
If device is externally calibrated, only calibrated values are printed.
++ : high alarm, + : high warning, - : low warning, -- : low alarm.
NA or N/A: not applicable, Tx: transmit, Rx: receive.
mA: milliamperes, dBm: decibels (milliwatts).
Optical Optical
Temperature Voltage Current Tx Power Rx Power
Port (Celsius) (Volts) (mA) (dBm) (dBm)
------- ----------- ------- -------- -------- --------
Gi2/1 43.7 5.03 50.6 + -16.7 -- N/A
Gi2/2 39.2 5.02 25.7 0.8 N/A
Switch#
This example shows how to display the detailed monitoring data for the interfaces that have transceivers installed on module 2:
Switch# show interfaces transceiver detail module 2
mA: milliamperes, dBm: decibels (milliwatts), NA or N/A: not applicable.
++ : high alarm, + : high warning, - : low warning, -- : low alarm.
A2D readouts (if they differ), are reported in parentheses.
The threshold values are calibrated.
High Alarm High Warn Low Warn Low Alarm
Temperature Threshold Threshold Threshold Threshold
Port (Celsius) (Celsius) (Celsius) (Celsius) (Celsius)
------- ------------------ ---------- --------- --------- ---------
Gi2/1 43.5 70.0 60.0 5.0 0.0
Gi2/2 39.1 70.0 60.0 5.0 0.0
High Alarm High Warn Low Warn Low Alarm
Voltage Threshold Threshold Threshold Threshold
Port (Volts) (Volts) (Volts) (Volts) (Volts)
------- --------------- ---------- --------- --------- ---------
Gi2/1 5.03 5.50 5.25 4.75 4.50
Gi2/2 5.02 5.50 5.25 4.75 4.50
High Alarm High Warn Low Warn Low Alarm
Current Threshold Threshold Threshold Threshold
Port (milliamperes) (mA) (mA) (mA) (mA)
------- ----------------- ---------- --------- --------- ---------
Gi2/1 50.6 + 60.0 40.0 10.0 5.0
Gi2/2 25.8 60.0 40.0 10.0 5.0
Optical High Alarm High Warn Low Warn Low Alarm
Transmit Power Threshold Threshold Threshold Threshold
Port (dBm) (dBm) (dBm) (dBm) (dBm)
------- ----------------- ---------- --------- --------- ---------
Gi2/1 -16.7 (-13.0) -- 3.4 3.2 -0.3 -0.5
Gi2/2 0.8 ( 5.1) 3.4 3.2 -0.3 -0.5
Optical High Alarm High Warn Low Warn Low Alarm
Receive Power Threshold Threshold Threshold Threshold
Port (dBm) (dBm) (dBm) (dBm) (dBm)
------- ----------------- ---------- --------- --------- ---------
Gi2/1 N/A (-28.5) 5.9 -6.7 -28.5 -28.5
Gi2/2 N/A (-19.5) 5.9 -6.7 -28.5 -28.5
Switch#
This example shows how to display the monitoring data for the transceivers on interface Gi1/2:
Switch# show interfaces g1/2 transceiver
ITU Channel 23 (1558.98 nm),
Transceiver is externally calibrated.
If device is externally calibrated, only calibrated values are printed.
++ : high alarm, + : high warning, - : low warning, -- : low alarm.
NA or N/A: not applicable, Tx: transmit, Rx: receive.
mA: milliamperes, dBm: decibels (milliwatts).
Optical Optical
Temperature Voltage Current Tx Power Rx Power
Port (Celsius) (Volts) (mA) (dBm) (dBm)
------- ----------- ------- -------- -------- --------
Gi2/1 43.7 5.03 50.6 + -16.7 -- N/A
Switch#
This example shows how to display detailed the monitoring data for the transceivers on interface Gi1/2:
Switch# show interfaces g1/2 transceiver detail
ITU Channel 23 (1558.98 nm),
Transceiver is externally calibrated.
mA: milliamperes, dBm: decibels (milliwatts), NA or N/A: not applicable.
++ : high alarm, + : high warning, - : low warning, -- : low alarm.
A2D readouts (if they differ), are reported in parentheses.
The threshold values are calibrated.
High Alarm High Warn Low Warn Low Alarm
Temperature Threshold Threshold Threshold Threshold
Port (Celsius) (Celsius) (Celsius) (Celsius) (Celsius)
------- ------------------ ---------- --------- --------- ---------
Gi2/1 43.5 70.0 60.0 5.0 0.0
High Alarm High Warn Low Warn Low Alarm
Voltage Threshold Threshold Threshold Threshold
Port (Volts) (Volts) (Volts) (Volts) (Volts)
------- --------------- ---------- --------- --------- ---------
Gi2/1 5.03 5.50 5.25 4.75 4.50
High Alarm High Warn Low Warn Low Alarm
Current Threshold Threshold Threshold Threshold
Port (milliamperes) (mA) (mA) (mA) (mA)
------- ----------------- ---------- --------- --------- ---------
Gi2/1 50.6 + 60.0 40.0 10.0 5.0
Optical High Alarm High Warn Low Warn Low Alarm
Transmit Power Threshold Threshold Threshold Threshold
Port (dBm) (dBm) (dBm) (dBm) (dBm)
------- ----------------- ---------- --------- --------- ---------
Gi2/1 -16.7 (-13.0) -- 3.4 3.2 -0.3 -0.5
Optical High Alarm High Warn Low Warn Low Alarm
Receive Power Threshold Threshold Threshold Threshold
Port (dBm) (dBm) (dBm) (dBm) (dBm)
------- ----------------- ---------- --------- --------- ---------
Gi2/1 N/A (-28.5) 5.9 -6.7 -28.5 -28.5
Switch#
Related Commands
|
|
---|---|
Displays the IDPROMs for the chassis. |
|
Displays the interface status or a list of interfaces in error-disabled state. |
show interfaces trunk
To display port and module interface-trunk information, use the show interfaces trunk command.
show interfaces trunk [module mod]
Syntax Description
module mod |
(Optional) Limits the display to interfaces on the specified module; valid values are from 1 to 6. |
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(8a)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Usage Guidelines
If you do not specify a keyword, only information for trunking ports is displayed.
Examples
This example shows how to display interface-trunk information for module 5:
Switch#
show interfaces trunk module 5
Port Mode Encapsulation Status Native vlan
Fa5/1 routed negotiate routed 1
Fa5/2 routed negotiate routed 1
Fa5/3 routed negotiate routed 1
Fa5/4 routed negotiate routed 1
Fa5/5 routed negotiate routed 1
Fa5/6 off negotiate not-trunking 10
Fa5/7 off negotiate not-trunking 10
Fa5/8 off negotiate not-trunking 1
Fa5/9 desirable n-isl trunking 1
Fa5/10 desirable negotiate not-trunking 1
Fa5/11 routed negotiate routed 1
Fa5/12 routed negotiate routed 1
...
Fa5/48 routed negotiate routed 1
Port Vlans allowed on trunk
Fa5/1 none
Fa5/2 none
Fa5/3 none
Fa5/4 none
Fa5/5 none
Fa5/6 none
Fa5/7 none
Fa5/8 200
Fa5/9 1-1005
Fa5/10 none
Fa5/11 none
Fa5/12 none
Fa5/48 none
Port Vlans allowed and active in management domain
Fa5/1 none
Fa5/2 none
Fa5/3 none
Fa5/4 none
Fa5/5 none
Fa5/6 none
Fa5/7 none
Fa5/8 200
Fa5/9 1-6,10,20,50,100,152,200,300,303-305,349-351,400,500,521,524,570,801-8
02,850,917,999,1002-1005
Fa5/10 none
Fa5/11 none
Fa5/12 none
Fa5/48 none
Port Vlans in spanning tree forwarding state and not pruned
Fa5/1 none
Fa5/2 none
Fa5/3 none
Fa5/4 none
Fa5/5 none
Fa5/6 none
Fa5/7 none
Fa5/8 200
Fa5/9 1-6,10,20,50,100,152,200,300,303-305,349-351,400,500,521,524,570,801-8
02,850,917,999,1002-1005
Fa5/10 none
Fa5/11 none
Fa5/48 none
Switch#
This example shows how to display trunking information for active trunking ports:
Switch#
show interfaces trunk
Port Mode Encapsulation Status Native vlan
Fa5/9 desirable n-isl trunking 1
Port Vlans allowed on trunk
Fa5/9 1-1005
Port Vlans allowed and active in management domain
Fa5/9 1-6,10,20,50,100,152,200,300,303-305,349-351,400,500,521,524,570,801-8
02,850,917,999,1002-1005
Port Vlans in spanning tree forwarding state and not pruned
Fa5/9 1-6,10,20,50,100,152,200,300,303-305,349-351,400,500,521,524,570,801-8
02,850,917,999,1002-1005
Switch#
show ip arp inspection
To show the status of dynamic ARP inspection for a specific range of VLANs, use the show ip arp inspection command.
show ip arp inspection {[statistics] vlan vlan-range | interfaces [interface-name]}
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(19)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Examples
This example shows how to display the statistics of packets that have been processed by DAI for
VLAN 3:
Switch# show ip arp inspection statistics vlan 3
Vlan Forwarded Dropped DHCP Drops ACL Drops
---- --------- ------- ---------- ----------
3 31753 102407 102407 0
Vlan DHCP Permits ACL Permits Source MAC Failures
---- ------------ ----------- -------------------
3 31753 0 0
Vlan Dest MAC Failures IP Validation Failures
---- ----------------- ----------------------
3 0 0
Switch#
This example shows how to display the statistics of packets that have been processed by DAI for all active VLANs:
Switch# show ip arp inspection statistics
Vlan Forwarded Dropped DHCP Drops ACL Drops
---- --------- ------- ---------- ----------
1 0 0 0 0
2 0 0 0 0
3 68322 220356 220356 0
4 0 0 0 0
100 0 0 0 0
101 0 0 0 0
1006 0 0 0 0
1007 0 0 0 0
Vlan DHCP Permits ACL Permits Source MAC Failures
---- ------------ ----------- -------------------
1 0 0 0
2 0 0 0
3 68322 0 0
4 0 0 0
100 0 0 0
101 0 0 0
1006 0 0 0
1007 0 0 0
Vlan Dest MAC Failures IP Validation Failures
---- ----------------- ----------------------
1 0 0
2 0 0
3 0 0
4 0 0
100 0 0
101 0 0
1006 0 0
1007 0 0
Switch#
This example shows how to display the configuration and operating state of DAI for VLAN 1:
Switch# show ip arp inspection vlan 1
Source Mac Validation : Disabled
Destination Mac Validation : Disabled
IP Address Validation : Disabled
Vlan Configuration Operation ACL Match Static ACL
---- ------------- --------- --------- ----------
1 Enabled Active
Vlan ACL Logging DHCP Logging
---- ----------- ------------
1 Deny Deny
Switch#
This example shows how to display the trust state of Fast Ethernet interface 6/1:
Switch# show ip arp inspection interfaces fastEthernet 6/1
Interface Trust State Rate (pps) Burst Interval
--------------- ----------- ---------- --------------
Fa6/1 Untrusted 20 5
Switch#
This example shows how to display the trust state of the interfaces on the switch:
Switch# show ip arp inspection interfaces
Interface Trust State Rate (pps)
--------------- ----------- ----------
Gi1/1 Untrusted 15
Gi1/2 Untrusted 15
Gi3/1 Untrusted 15
Gi3/2 Untrusted 15
Fa3/3 Trusted None
Fa3/4 Untrusted 15
Fa3/5 Untrusted 15
Fa3/6 Untrusted 15
Fa3/7 Untrusted 15
Switch#
Related Commands
|
|
---|---|
Defines an ARP access list or adds clauses at the end of a predefined list. |
|
Clears the status of the log buffer. |
|
Displays the status of the log buffer. |
show ip arp inspection log
To show the status of the log buffer, use the show ip arp inspection log command.
show ip arp inspection log
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(19)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Examples
This example shows how to display the current contents of the log buffer before and after the buffers are cleared:
Switch# show ip arp inspection log
Total Log Buffer Size : 10
Syslog rate : 0 entries per 10 seconds.
Interface Vlan Sender MAC Sender IP Num of Pkts
--------------- ----- ----------------- --------------- -----------
Fa6/3 1 0002.0002.0002 1.1.1.2 1(12:02:52 UTC Fri Apr 25 2003)
Fa6/3 1 0002.0002.0002 1.1.1.3 1(12:02:52 UTC Fri Apr 25 2003)
Fa6/3 1 0002.0002.0002 1.1.1.4 1(12:02:52 UTC Fri Apr 25 2003)
Fa6/3 1 0002.0002.0002 1.1.1.5 1(12:02:52 UTC Fri Apr 25 2003)
Fa6/3 1 0002.0002.0002 1.1.1.6 1(12:02:52 UTC Fri Apr 25 2003)
Fa6/3 1 0002.0002.0002 1.1.1.7 1(12:02:52 UTC Fri Apr 25 2003)
Fa6/3 1 0002.0002.0002 1.1.1.8 1(12:02:52 UTC Fri Apr 25 2003)
Fa6/3 1 0002.0002.0002 1.1.1.9 1(12:02:52 UTC Fri Apr 25 2003)
Fa6/3 1 0002.0002.0002 1.1.1.10 1(12:02:52 UTC Fri Apr 25 2003)
Fa6/3 1 0002.0002.0002 1.1.1.11 1(12:02:52 UTC Fri Apr 25 2003)
-- -- -- -- 5(12:02:52 UTC Fri Apr 25 2003)
Switch#
This example shows how to clear the buffer with the clear ip arp inspection log command:
Switch# clear ip arp inspection log
Switch# show ip arp inspection log
Total Log Buffer Size : 10
Syslog rate : 0 entries per 10 seconds.
No entries in log buffer.
Switch#
Related Commands
|
|
---|---|
Defines an ARP access list or adds clauses at the end of a predefined list. |
|
Clears the status of the log buffer. |
show ip cef vlan
To view IP CEF VLAN interface status and configuration information and display the prefixes for a specific interface, use the show ip cef vlan command.
show ip cef vlan vlan_num [detail]
Syntax Description
vlan_num |
Number of the VLAN. |
detail |
(Optional) Displays detailed information. |
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(8a)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Examples
This example shows how to display the prefixes for a specific VLAN:
Switch# show ip cef vlan 1003
Prefix Next Hop Interface
0.0.0.0/0 172.20.52.1 FastEthernet3/3
0.0.0.0/32 receive
10.7.0.0/16 172.20.52.1 FastEthernet3/3
10.16.18.0/23 172.20.52.1 FastEthernet3/3
Switch#
This example shows how to display detailed IP CEF information for a specific VLAN:
Switch# show ip cef vlan 1003 detail
IP Distributed CEF with switching (Table Version 2364), flags=0x0
1383 routes, 0 reresolve, 0 unresolved (0 old, 0 new)
1383 leaves, 201 nodes, 380532 bytes, 2372 inserts, 989 invalidations
0 load sharing elements, 0 bytes, 0 references
universal per-destination load sharing algorithm, id 9B6C9823
3 CEF resets, 0 revisions of existing leaves
refcounts: 54276 leaf, 51712 node
Adjacency Table has 5 adjacencies
Switch#
show ip dhcp snooping
To display the DHCP snooping configuration, use the show ip dhcp snooping command.
show ip dhcp snooping
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(12c)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
12.2(25)EWA |
Support for option 82 on untrusted ports was added. |
Examples
This example shows how to display the DHCP snooping configuration:
Switch# show ip dhcp snooping
Switch DHCP snooping is enabled
DHCP snooping is configured on following VLANs:
500,555
DHCP snooping is operational on following VLANs:
500,555
DHCP snooping is configured on the following L3 Interfaces:
Insertion of option 82 is enabled
circuit-id default format: vlan-mod-port
remote-id: switch123 (string)
Option 82 on untrusted port is not allowed Verification of hwaddr field is enabled DHCP snooping trust/rate is configured on the following Interfaces:
Interface Trusted Rate limit (pps)
------------------------ ------- ----------------
FastEthernet5/1 yes 100
Custom circuit-ids:
VLAN 555: customer-555
FastEthernet2/1 no unlimited
Custom circuit-ids:
VLAN 500: customer-500
Switch#
Related Commands
show ip dhcp snooping binding
To display the DHCP snooping binding entries, use the show ip dhcp snooping binding command.
show ip dhcp snooping binding [ip-address] [mac-address] [vlan vlan_num]
[interface interface_num]
Syntax Description
Defaults
If no argument is specified, the switch will display the entire DHCP snooping binding table.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(12c)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Usage Guidelines
DHCP snooping is enabled on a VLAN only if both the global snooping and the VLAN snooping are enabled.
To configure a range of VLANs, use the optional last_vlan argument to specify the end of the VLAN range.
Examples
This example shows how to display the DHCP snooping binding entries for a switch:
Switch# show ip dhcp snooping binding
MacAddress IP Address Lease (seconds) Type VLAN Interface ----------- ----------- ---------------- ------------- ----- ------------ 0000.0100.0201 10.0.0.1 1600 dhcp-snooping 100 FastEthernet3/1
Switch#
This example shows how to display an IP address for DHCP snooping binding entries:
Switch# show ip dhcp snooping binding 172.100.101.102
MacAddress IP Address Lease (seconds) Type VLAN Interface ----------- ----------- ---------------- ------------- ----- ------------ 0000.0100.0201 172.100.101.102 1600 dhcp-snooping 100 FastEthernet3/1
Switch#
This example shows how to display the MAC address for the DHCP snooping binding entries:
Switch# show ip dhcp snooping binding 55.5.5.2 0002.b33f.3d5f
MacAddress IpAddress Lease(sec) Type VLAN Interface
------------------ --------------- ---------- ------------- ---- --------------------
00:02:B3:3F:3D:5F 55.5.5.2 492 dhcp-snooping 99 FastEthernet6/36
Switch#
This example shows how to display the DHCP snooping binding entries' MAC address for a specific VLAN:
Switch# show ip dhcp snooping binding 55.5.5.2 0002.b33f.3d5f vlan 99
MacAddress IpAddress Lease(sec) Type VLAN Interface
------------------ --------------- ---------- ------------- ---- --------------------
00:02:B3:3F:3D:5F 55.5.5.2 479 dhcp-snooping 99 FastEthernet6/36
Switch#
This example shows how to display the dynamic DHCP snooping binding entries:
Switch# show ip dhcp snooping binding dynamic
MacAddress IP Address Lease (seconds) Type VLAN Interface ----------- ----------- ---------------- ------------ ----- ------------ 0000.0100.0201 10.0.0.1 1600 dhcp-snooping 100 FastEthernet3/1
Switch#
This example shows how to display the DHCP snooping binding entries on VLAN 100:
Switch# show ip dhcp snooping binding vlan 100'
MacAddress IP Address Lease (seconds) Type VLAN Interface ----------- ----------- ---------------- ------------ ----- ------------ 0000.0100.0201 10.0.0.1 1600 dhcp-snooping 100 FastEthernet3/1
Switch#
This example shows how to display the DHCP snooping binding entries on Ethernet interface 0/1:
Switch# show ip dhcp snooping binding interface fastethernet3/1
MacAddress IP Address Lease (seconds) Type VLAN Interface ----------- ----------- ---------------- ------------ ----- ------------ 0000.0100.0201 10.0.0.1 1600 dhcp-snooping 100 FastEthernet3/1
Switch#
Table 2-21 describes the fields in the show ip dhcp snooping command output.
Related Commands
show ip dhcp snooping database
To display the status of the DHCP snooping database agent, use the show ip dhcp snooping database command.
show ip dhcp snooping database [detail]
Syntax Description
detail |
(Optional) Provides additional operating state and statistics information. |
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(12c)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
12.1(19)EW |
Added support of state and statistics information. |
Examples
This example shows how to display the DHCP snooping database:
Switch# show ip dhcp snooping database
Agent URL :
Write delay Timer : 300 seconds
Abort Timer : 300 seconds
Agent Running : No
Delay Timer Expiry : Not Running
Abort Timer Expiry : Not Running
Last Succeded Time : None
Last Failed Time : None
Last Failed Reason : No failure recorded.
Total Attempts : 0 Startup Failures : 0
Successful Transfers : 0 Failed Transfers : 0
Successful Reads : 0 Failed Reads : 0
Successful Writes : 0 Failed Writes : 0
Media Failures : 0
Switch#
This example shows how to view additional operating statistics:
Switch# show ip dhcp snooping database detail
Agent URL : tftp://10.1.1.1/directory/file
Write delay Timer : 300 seconds
Abort Timer : 300 seconds
Agent Running : No
Delay Timer Expiry : 7 (00:00:07)
Abort Timer Expiry : Not Running
Last Succeded Time : None
Last Failed Time : 17:14:25 UTC Sat Jul 7 2001
Last Failed Reason : Unable to access URL.
Total Attempts : 21 Startup Failures : 0
Successful Transfers : 0 Failed Transfers : 21
Successful Reads : 0 Failed Reads : 0
Successful Writes : 0 Failed Writes : 21
Media Failures : 0
First successful access: Read
Last ignored bindings counters :
Binding Collisions : 0 Expired leases : 0
Invalid interfaces : 0 Unsupported vlans : 0
Parse failures : 0
Last Ignored Time : None
Total ignored bindings counters:
Binding Collisions : 0 Expired leases : 0
Invalid interfaces : 0 Unsupported vlans : 0
Parse failures : 0
Switch#
Related Commands
show ip igmp interface
To view IP IGMP interface status and configuration information, use the show ip igmp interface command.
show ip igmp interface [fastethernet slot/port | gigabitethernet slot/port |
tengigabitethernet slot/port | null interface-number | vlan vlan_id]
Syntax Description
Defaults
If you do not specify a VLAN, information for VLAN 1 is shown.
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
If you omit the optional arguments, the show ip igmp interface command displays information about all interfaces.
Examples
This example shows how to view IGMP information for VLAN 200:
Switch# show ip igmp interface vlan 200
IGMP snooping is globally enabled
IGMP snooping is enabled on this Vlan
IGMP snooping immediate-leave is disabled on this Vlan
IGMP snooping mrouter learn mode is pim-dvmrp on this Vlan
IGMP snooping is running in IGMP-ONLY mode on this VLAN
Switch#
Related Commands
|
|
---|---|
Deletes the IGMP group cache entries. |
|
Displays information on the dynamically learned and manually configured multicast switch interfaces. |
show ip igmp profile
To view all configured IGMP profiles or a specified IGMP profile, use the show ip igmp profile privileged EXEC command.
show ip igmp profile [profile number]
Syntax Description
profile number |
(Optional) IGMP profile number to be displayed; valid ranges are from 1 to 4294967295. |
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(11b)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Usage Guidelines
If no profile number is entered, all IGMP profiles are displayed.
Examples
This example shows how to display IGMP profile 40:
Switch# show ip igmp profile 40
IGMP Profile 40
permit
range 233.1.1.1 233.255.255.255
Switch#
This example shows how to display all IGMP profiles:
Switch# show ip igmp profile
IGMP Profile 3
range 230.9.9.0 230.9.9.0
IGMP Profile 4
permit
range 229.9.9.0 229.255.255.255
Switch#
Related Commands
|
|
---|---|
Creates an IGMP profile. |
show ip igmp snooping
To display information on dynamically learned and manually configured VLAN switch interfaces, use the show ip igmp snooping command.
show ip igmp snooping [querier | groups | mrouter] [vlan vlan_id] a.b.c.d [summary | sources | hosts] [count]
Syntax Description
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
Usage Guidelines
You can also use the show mac-address-table multicast command to display the entries in the MAC address table for a VLAN that has IGMP snooping enabled.
You can display IGMP snooping information for VLAN interfaces by entering the show ip igmp snooping command.
Examples
This example shows how to display the global snooping information on the switch:
Switch# show ip igmp snooping
Global IGMP Snooping configuration:
-----------------------------------
IGMP snooping : Enabled
IGMPv3 snooping : Enabled
Report suppression : Enabled
TCN solicit query : Disabled
TCN flood query count : 2
Vlan 1:
--------
IGMP snooping : Enabled
IGMPv2 immediate leave : Disabled
Explicit host tracking : Enabled
Multicast router learning mode : pim-dvmrp
CGMP interoperability mode : IGMP_ONLY
Vlan 2:
--------
IGMP snooping : Enabled
IGMPv2 immediate leave : Disabled
Explicit host tracking : Enabled
Multicast router learning mode : pim-dvmrp
CGMP interoperability mode : IGMP_ONLY
Switch>
This example shows how to display the snooping information on VLAN 2:
Switch# show ip igmp snooping vlan 2
Global IGMP Snooping configuration:
-----------------------------------
IGMP snooping : Enabled
IGMPv3 snooping : Enabled
Report suppression : Enabled
TCN solicit query : Disabled
TCN flood query count : 2
Vlan 2:
--------
IGMP snooping : Enabled
IGMPv2 immediate leave : Disabled
Explicit host tracking : Enabled
Multicast router learning mode : pim-dvmrp
CGMP interoperability mode : IGMP_ONLY
Switch>
This example shows how to display IGMP querier information for all VLANs on a switch:
Switch# show ip igmp snooping querier
Vlan IP Address IGMP Version Port
---------------------------------------------------
2 10.10.10.1 v2 Router
3 172.20.50.22 v3 Fa3/15
Switch>
This example shows how to display IGMP querier information for VLAN 5 when running IGMPv2:
Switch# show ip igmp snooping querier vlan 5
IP address :5.5.5.10
IGMP version :v2
Port :Fa3/1
Max response time :10s
Switch>
This example shows how to display IGMP querier information for VLAN 5 when running IGMPv3:
Switch# show ip igmp snooping querier vlan 5
IP address :5.5.5.10
IGMP version :v3
Port :Fa3/1
Max response time :10s
Query interval :60s
Robustness variable :2
Switch>
This example shows how to display snooping information for a specific group:
Switch#
show ip igmp snooping group
Vlan Group Version Ports
---------------------------------------------------------
2 224.0.1.40 v3 Router
2 224.2.2.2 v3 Fa6/2
Switch>
This example shows how to display the group's host types and ports in VLAN 1:
Switch# show ip igmp snooping group vlan 1
Vlan Group Host Type Ports
---------------------------------------------------------
1 229.2.3.4 v3 fa2/1 fa2/3
1 224.2.2.2 v3 Fa6/2
Switch>
This example shows how to display the group's host types and ports in VLAN 1:
Switch# show ip igmp snooping group vlan 10 226.6.6.7
Vlan Group Version Ports
---------------------------------------------------------
10 226.6.6.7 v3 Fa7/13, Fa7/14
Switch>
This example shows how to display the current state of a group with respect to a source IP address:
Switch# show ip igmp snooping group vlan 10 226.6.6.7 sources
Source information for group 226.6.6.7:
Timers: Expired sources are deleted on next IGMP General Query
SourceIP Expires Uptime Inc Hosts Exc Hosts
-------------------------------------------------------
2.0.0.1 00:03:04 00:03:48 2 0
2.0.0.2 00:03:04 00:02:07 2 0
Switch>
This example shows how to display the current state of a group with respect to a host MAC address:
Switch# show ip igmp snooping group vlan 10 226.6.6.7 hosts
IGMPv3 host information for group 226.6.6.7
Timers: Expired hosts are deleted on next IGMP General Query
Host (MAC/IP) Filter mode Expires Uptime # Sources
-------------------------------------------------------------
175.1.0.29 INCLUDE stopped 00:00:51 2
175.2.0.30 INCLUDE stopped 00:04:14 2
Switch>
This example shows how to display summary information for a v3 group:
Switch# show ip igmp snooping group vlan 10 226.6.6.7 summary
Group Address (Vlan 10) : 226.6.6.7
Host type : v3
Member Ports : Fa7/13, Fa7/14
Filter mode : INCLUDE
Expires : stopped
Sources : 2
Reporters (Include/Exclude) : 2/0
Switch>
This example shows how to display multicast router information for VLAN 1:
Switch#
show ip igmp snooping mrouter vlan 1
vlan ports
-----+----------------------------------------
1 Gi1/1,Gi2/1,Fa3/48,Router
Switch#
This example shows how to display the total number of group addresses learned by the system globally:
Switch# show ip igmp snooping group count
Total number of groups: 54
Switch>
This example shows how to display the total number of group addresses learned on VLAN 5:
Switch# show ip igmp snooping group vlan 5 count
Total number of groups: 30
Switch>
Related Commands
show ip igmp snooping membership
To display host membership information, use the show ip igmp snooping membership command.
show ip igmp snooping membership [interface interface_num] [vlan vlan_id]
[reporter a.b.c.d] [source a.b.c.d group a.b.c.d]
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(20)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
12.2(25)EW |
Added support for the 10-Gigabit Ethernet interface. |
Usage Guidelines
This command is valid only if explicit host tracking is enabled on the switch.
Examples
This example shows how to display host membership for the Gigabit Ethernet interface 4/1:
Switch# show ip igmp snooping membership interface gigabitethernet4/1
#channels: 5
#hosts : 1
Source/Group Interface Reporter Uptime Last-Join Last-Leave
40.40.40.2/224.10.10.10 Gi4/1 20.20.20 .20 00:23: 37 00:06: 50 00:20:30
40.40.40.4/224.10.10.10 Gi4/1 20.20.20 .20 00:39: 42 00:09:17 -
Switch#
This example shows how to display host membership for VLAN 20 and group 224.10.10.10:
Switch# show ip igmp snooping membership vlan 20 source 40.40.40.2 group 224.10.10.10
#channels: 5
#hosts : 1
Source/Group Interface Reporter Uptime Last-Join Last-Leave
40.40.40.2/224.10.10.10 Gi4/1 20.20.20 .20 00:23: 37 00:06: 50 00:20:30
Switch#
This example shows how to display host membership information for VLAN 20 and to delete the explicit host tracking:
Switch# show ip igmp snooping membership vlan 20
Snooping Membership Summary for Vlan 20
------------------------------------------
Total number of channels:5
Total number of hosts :4
Source/Group Interface Reporter Uptime Last-Join/
Last-Leave
-------------------------------------------------------------------------------------------------------
40.0.0.1/224.1.1.1 Fa7/37 0002.4ba0.a4f6 00:00:04 00:00:04 /
-
40.0.0.2/224.1.1.1 Fa7/37 0002.fd80.f770 00:00:17 00:00:17 /
-
40.0.0.3/224.1.1.1 Fa7/36 20.20.20.20 00:00:04 00:00:04 /
-
40.0.0.4/224.1.1.1 Fa7/35 20.20.20.210 00:00:17 00:00:17 /
-
40.0.0.5/224.1.1.1 Fa7/37 0002.fd80.f770 00:00:17 00:00:17 /
-
Switch# clear ip igmp snooping membership vlan 20
Switch#
Related Commands
|
|
---|---|
Clears the explicit host tracking database. |
|
Enables per-VLAN explicit host tracking. |
|
Displays information on dynamically learned and manually configured VLAN switch interfaces. |
show ip igmp snooping mrouter
To display information on the dynamically learned and manually configured multicast switch interfaces, use the show ip igmp snooping mrouter command.
show ip igmp snooping mrouter [{vlan vlan-id}]
Syntax Description
vlan vlan-id |
(Optional) Specifies a VLAN; valid values are from 1 to 1001 and from 1006 to 4094. |
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(8a)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
12.1(19)EW |
Added support for extended VLAN addresses. |
Usage Guidelines
You can also use the show mac-address-table multicast command to display entries in the MAC address table for a VLAN that has IGMP snooping enabled.
You can display IGMP snooping information for the VLAN interfaces by entering the show ip igmp interface vlan vlan-num command.
Examples
This example shows how to display snooping information for a specific VLAN:
Switch#
show ip igmp snooping mrouter vlan 1
vlan ports
-----+----------------------------------------
1 Gi1/1,Gi2/1,Fa3/48,Switch
Switch#
Related Commands
show ip igmp snooping vlan
To display information on the dynamically learned and manually configured VLAN switch interfaces, use the show ip igmp snooping vlan command.
show ip igmp snooping vlan vlan_num
Syntax Description
vlan_num |
Number of the VLAN; valid values are from 1 to 1001 and from 1006 to 4094. |
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(8a)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
12.1(12c)EW |
Support for extended addressing was added. |
Usage Guidelines
You can also use the show mac-address-table multicast command to display the entries in the MAC address table for a VLAN that has IGMP snooping enabled.
Examples
This example shows how to display snooping information for a specific VLAN:
Switch#
show ip igmp snooping vlan 2
vlan 2
----------
IGMP snooping is globally enabled
IGMP snooping TCN solicit query is globally enabled
IGMP snooping global TCN flood query count is 2
IGMP snooping is enabled on this Vlan
IGMP snooping immediate-leave is disabled on this Vlan
IGMP snooping mrouter learn mode is pim-dvmrp on this Vlan
IGMP snooping is running in IGMP_ONLY mode on this Vlan
Switch#
Related Commands
show ip interface
To display the usability status of interfaces that are configured for IP, use the show ip interface command.
show ip interface [type number]
Syntax Description
type |
(Optional) Interface type. |
number |
(Optional) Interface number. |
Defaults
This command has no default settings.
Command Modes
EXEC
Command History
|
|
---|---|
12.2(25)EW |
Extended to include the 10-Gigabit Ethernet interface. |
Usage Guidelines
The Cisco IOS software automatically enters a directly connected route in the routing table if the interface is usable. A usable interface is one through which the software can send and receive packets. If the software determines that an interface is not usable, it removes the directly connected routing entry from the routing table. Removing the entry allows the software to use dynamic routing protocols to determine backup routes to the network, if any.
If the interface can provide two-way communication, the line protocol is marked "up." If the interface hardware is usable, the interface is marked "up."
If you specify an optional interface type, you see information only on that specific interface.
If you specify no optional arguments, you see information on all the interfaces.
When an asynchronous interface is encapsulated with PPP or Serial Line Internet Protocol (SLIP), IP fast switching is enabled. The show ip interface command on an asynchronous interface that is encapsulated with PPP or SLIP displays a message indicating that IP fast switching is enabled.
Examples
This example shows how to display the usability status for a specific VLAN:
Switch# show ip interface vlan 1
Vlan1 is up, line protocol is up
Internet address is 10.6.58.4/24
Broadcast address is 255.255.255.255
Address determined by non-volatile memory
MTU is 1500 bytes
Helper address is not set
Directed broadcast forwarding is disabled
Outgoing access list is not set
Inbound access list is not set
Proxy ARP is enabled
Local Proxy ARP is disabled
Security level is default
Split horizon is enabled
ICMP redirects are always sent
ICMP unreachables are always sent
ICMP mask replies are never sent
IP fast switching is enabled
IP fast switching on the same interface is disabled
IP Flow switching is disabled
IP CEF switching is enabled
IP Fast switching turbo vector
IP Normal CEF switching turbo vector
IP multicast fast switching is enabled
IP multicast distributed fast switching is disabled
IP route-cache flags are Fast, CEF
Router Discovery is disabled
IP output packet accounting is disabled
IP access violation accounting is disabled
TCP/IP header compression is disabled
RTP/IP header compression is disabled
Probe proxy name replies are disabled
Policy routing is disabled
Network address translation is disabled
WCCP Redirect outbound is disabled
WCCP Redirect inbound is disabled
WCCP Redirect exclude is disabled
BGP Policy Mapping is disabled
Sampled Netflow is disabled
IP multicast multilayer switching is disabled
Netflow Data Export (hardware) is enabled
Switch#
Table 2-22 describes the fields that are shown in the example.
show ip mfib
To display all active Multicast Forwarding Information Base (MFIB) routes, use the show ip mfib command.
show ip mfib [all | counters | log [n]]
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
In the Supervisor Engine 6-E and Catalyst 4900M chassis, the output of the show ip mfib command does not display any hardware counters.
The MFIB table contains a set of IP multicast routes; each route in the MFIB table contains several flags that associate to the route.
The route flags indicate how a packet that matches a route is forwarded. For example, the IC flag on an MFIB route indicates that some process on the switch needs to receive a copy of the packet. These flags are associated with MFIB routes:
•Internal Copy (IC) flag—Set on a route when a process on the switch needs to receive a copy of all packets matching the specified route.
•Signaling (S) flag—Set on a route when a switch process needs notification that a packet matching the route is received. In the expected behavior, the protocol code updates the MFIB state in response to having received a packet on a signaling interface.
•Connected (C) flag—When set on a route, the C flag has the same meaning as the S flag, except that the C flag indicates that only packets sent by directly connected hosts to the route should be signaled to a protocol process.
A route can also have a set of flags associated with one or more interfaces. For an (S,G) route, the flags on interface 1 indicate how the ingress packets should be treated and whether packets matching the route should be forwarded onto interface 1. These per-interface flags are associated with the MFIB routes:
•Accepting (A)—Set on the RPF interface when a packet that arrives on the interface and that is marked as Accepting (A) is forwarded to all Forwarding (F) interfaces.
•Forwarding (F)—Used with the A flag as described above. The set of forwarding interfaces together form a multicast olist or output interface list.
•Signaling (S)—Set on an interface when a multicast routing protocol process in Cisco IOS needs to be notified of ingress packets on that interface.
•Not Platform (NP) fast-switched—Used with the F flag. A forwarding interface is also marked as Not Platform fast-switched whenever that output interface cannot be fast-switched by the platform hardware and requires software forwarding.
For example, the Catalyst 4506 switch with Supervisor Engine III cannot switch tunnel interfaces in hardware so these interfaces are marked with the NP flag. When an NP interface is associated with a route, a copy of every ingress packet arriving on an Accepting interface is sent to the switch software forwarding path for software replication and then forwarded to the NP interface.
Examples
This example shows how to display all active MFIB routes:
Switch# show ip mfib
IP Multicast Forwarding Information Base
Entry Flags: C - Directly Connected, S - Signal,
IC - Internal Copy
Interface Flags: A - Accept, F - Forward, NS - Signal,
NP - Not platform switched
Packets: Fast/Partial/Slow Bytes: Fast/Partial/Slow:
(171.69.10.13, 224.0.1.40), flags (IC)
Packets: 2292/2292/0, Bytes: 518803/0/518803
Vlan7 (A)
Vlan100 (F NS)
Vlan105 (F NS)
(*, 224.0.1.60), flags ()
Packets: 2292/0/0, Bytes: 518803/0/0
Vlan7 (A NS)
(*, 224.0.1.75), flags ()
Vlan7 (A NS)
(10.34.2.92, 239.192.128.80), flags ()
Packets: 24579/100/0, 2113788/15000/0 bytes
Vlan7 (F NS)
Vlan100 (A)
(*, 239.193.100.70), flags ()
Packets: 1/0/0, 1500/0/0 bytes
Vlan7 (A)
Switch#
Related Commands
|
|
---|---|
Clears the global MFIB counters and the counters for all active MFIB routes. |
show ip mfib fastdrop
To display all currently active fast-drop entries and to show whether fast drop is enabled, use the show ip mfib fastdrop command.
show ip mfib fastdrop
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(8a)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Examples
This example shows how to display all currently active fast-drop entries and whether fast drop is enabled.
Switch# show ip mfib fasttdrop
MFIB fastdrop is enabled.
MFIB fast-dropped flows:
(10.0.0.1, 224.1.2.3, Vlan9 ) 00:01:32
(10.1.0.2, 224.1.2.3, Vlan9 ) 00:02:30
(1.2.3.4, 225.6.7.8, Vlan3) 00:01:50
Switch#
Related Commands
|
|
---|---|
Clears all the MFIB fast-drop entries. |
show ip mroute
To display IP multicast routing table information, use the show ip mroute command.
show ip mroute [interface_type slot/port | host_name | host_address [source] | active [kbps | interface_type num] | count | pruned | static | summary]
Syntax Description
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(8a)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
12.2(25)EW |
Added support for the 10-Gigabit Ethernet interface. |
Usage Guidelines
If you omit all the optional arguments and keywords, the show ip mroute command displays all the entries in the IP multicast routing table.
The show ip mroute active kbps command displays all the sources sending at a rate greater than or equal to kbps.
The multicast routing table is populated by creating source, group (S,G) entries from star, group (*,G) entries. The star refers to all source addresses, the "S" refers to a single source address, and the "G" refers to the destination multicast group address. In creating (S,G) entries, the software uses the best path to that destination group found in the unicast routing table (through Reverse Path Forwarding (RPF).
Examples
This example shows how to display all the entries in the IP multicast routing table:
Switch# show ip mroute
IP Multicast Routing Table
Flags:D - Dense, S - Sparse, s - SSM Group, C - Connected, L - Local,
P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set,
J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running
A - Advertised via MSDP, U - URD, I - Received Source Specific Host
Report
Outgoing interface flags:H - Hardware switched
Timers:Uptime/Expires
Interface state:Interface, Next-Hop or VCD, State/Mode
(*, 230.13.13.1), 00:16:41/00:00:00, RP 10.15.1.20, flags:SJC
Incoming interface:GigabitEthernet4/8, RPF nbr 10.15.1.20
Outgoing interface list:
GigabitEthernet4/9, Forward/Sparse-Dense, 00:16:41/00:00:00, H
(*, 230.13.13.2), 00:16:41/00:00:00, RP 10.15.1.20, flags:SJC
Incoming interface:GigabitEthernet4/8, RPF nbr 10.15.1.20, RPF-MFD
Outgoing interface list:
GigabitEthernet4/9, Forward/Sparse-Dense, 00:16:41/00:00:00, H
(10.20.1.15, 230.13.13.1), 00:14:31/00:01:40, flags:CJT
Incoming interface:GigabitEthernet4/8, RPF nbr 10.15.1.20, RPF-MFD
Outgoing interface list:
GigabitEthernet4/9, Forward/Sparse-Dense, 00:14:31/00:00:00, H
(132.206.72.28, 224.2.136.89), 00:14:31/00:01:40, flags:CJT
Incoming interface:GigabitEthernet4/8, RPF nbr 10.15.1.20, RPF-MFD
Outgoing interface list:Null
Switch#
This example shows how to display the rate that the active sources are sending to the multicast groups and to display only the active sources that are sending at greater than the default rate:
Switch# show ip mroute active
Active IP Multicast Sources - sending > = 4 kbps
Group: 224.2.127.254, (sdr.cisco.com)
Source: 146.137.28.69 (mbone.ipd.anl.gov)
Rate: 1 pps/4 kbps(1sec), 4 kbps(last 1 secs), 4 kbps(life avg)
Group: 224.2.201.241, ACM 97
Source: 130.129.52.160 (webcast3-e1.acm97.interop.net)
Rate: 9 pps/93 kbps(1sec), 145 kbps(last 20 secs), 85 kbps(life avg)
Group: 224.2.207.215, ACM 97
Source: 130.129.52.160 (webcast3-e1.acm97.interop.net)
Rate: 3 pps/31 kbps(1sec), 63 kbps(last 19 secs), 65 kbps(life avg)
Switch#
This example shows how to display route and packet count information:
Switch# show ip mroute count
IP Multicast Statistics
56 routes using 28552 bytes of memory
13 groups, 3.30 average sources per group
Forwarding Counts:Pkt Count/Pkts per second/Avg Pkt Size/Kilobits per second
Other counts:Total/RPF failed/Other drops(OIF-null, rate-limit etc)
Group:224.2.136.89, Source count:1, Group pkt count:29051
Source:132.206.72.28/32, Forwarding:29051/-278/1186/0, Other:85724/8/56665
Switch#
This example shows how to display summary information:
Switch# show ip mroute summary
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, s - SSM Group, C - Connected, L - Local,
P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set,
J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running
A - Advertised via MSDP, U - URD, I - Received Source Specific Host
Report
Outgoing interface flags: H - Hardware switched
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
Switch#
Table 2-23 describes the fields shown in the output.
Related Commands
show ip source binding
To display IP source bindings that are configured on the system, use the show ip source binding EXEC command.
show ip source binding [ip-address] [mac-address] [dhcp-snooping | static] [vlan vlan-id] [interface interface-name]
Syntax Description
Defaults
Displays both static and DHCP snooping bindings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(19)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Usage Guidelines
The optional parameters filter the display output result.
Examples
This example shows how to display the IP source bindings:
Switch# show ip source binding
MacAddress IpAddress Lease(sec) Type VLAN Interface
------------------ --------------- ---------- ------------- ---- --------------------
00:00:00:0A:00:0B 11.0.0.1 infinite static 10 FastEthernet6/10
Switch#
This example shows how to display the static IP binding entry of IP address 11.0.01:
Switch# show ip source binding 11.0.0.1 0000.000A.000B static vlan 10 interface Fa6/10
show ip source binding 11.0.0.1 0000.000A.000B static vlan 10 interface Fa6/10
MacAddress IpAddress Lease(sec) Type VLAN Interface
------------------ --------------- ---------- ------------- ---- --------------------
00:00:00:0A:00:0B 11.0.0.1 infinite static 10 FastEthernet6/10 Switch#
Related Commands
|
|
---|---|
Adds or deletes a static IP source binding entry. |
show ip verify source
To display the IP source guard configuration and filters on a particular interface, use the show ip verify source command.
show ip verify source [interface interface_num]
Syntax Description
interface interface_num |
(Optional) Specifies an interface. |
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(19)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Examples
These examples show how to display the IP source guard configuration and filters on a particular interface with the show ip verify source interface command:
•This output appears when DHCP snooping is enabled on VLANs 10-20, interface fa6/1 has IP source filter mode that is configured as IP, and an existing IP address binding 10.0.0.1 is on VLAN 10:
Interface Filter-type Filter-mode IP-address Mac-address Vlan
--------- ----------- ----------- --------------- -------------- ---------
fa6/1 ip active 10.0.0.1 10
fa6/1 ip active deny-all 11-20
Note The second entry shows that a default PVACL (deny all IP traffic) is installed on the port for those snooping-enabled VLANs that do not have a valid IP source binding.
•This output appears when you enter the show ip verify source interface fa6/2 command and DHCP snooping is enabled on VLANs 10-20, interface fa6/1 has IP source filter mode that is configured as IP, and there is an existing IP address binding 10.0.0.1 on VLAN 10:
Interface Filter-type Filter-mode IP-address Mac-address Vlan
--------- ----------- ----------- --------------- -------------- ---------
fa6/2 ip inactive-trust-port
•This output appears when you enter the show ip verify source interface fa6/3 command and the interface fa6/3 does not have a VLAN enabled for DHCP snooping:
Interface Filter-type Filter-mode IP-address Mac-address Vlan
--------- ----------- ----------- --------------- -------------- ---------
fa6/3 ip inactive-no-snooping-vlan
•This output appears when you enter the show ip verify source interface fa6/4 command and the interface fa6/4 has an IP source filter mode that is configured as IP MAC and the existing IP MAC that binds 10.0.0.2/aaaa.bbbb.cccc on VLAN 10 and 11.0.0.1/aaaa.bbbb.cccd on VLAN 11:
Interface Filter-type Filter-mode IP-address Mac-address Vlan
--------- ----------- ----------- --------------- -------------- ---------
fa6/4 ip-mac active 10.0.0.2 aaaa.bbbb.cccc 10
fa6/4 ip-mac active 11.0.0.1 aaaa.bbbb.cccd 11
fa6/4 ip-mac active deny-all deny-all 12-20
•This output appears when you enter the show ip verify source interface fa6/5 command and the interface fa6/5 has IP source filter mode that is configured as IP MAC and existing IP MAC binding 10.0.0.3/aaaa.bbbb.ccce on VLAN 10, but port security is not enabled on fa6/5:
Interface Filter-type Filter-mode IP-address Mac-address Vlan
--------- ----------- ----------- --------------- -------------- ---------
fa6/5 ip-mac active 10.0.0.3 permit-all 10
fa6/5 ip-mac active deny-all permit-all 11-20
Note Enable port security first because the DHCP security MAC filter cannot apply to the port or VLAN.
•This output appears when you enter the show ip verify source interface fa6/6 command and the interface fa6/6 does not have IP source filter mode that is configured:
DHCP security is not configured on the interface fa6/6.
This example shows how to display all the interfaces on the switch that have DHCP snooping security and IP Port Security tracking enabled with the show ip verify source command.
The output is an accumulation of per-interface show CLIs:
Interface Filter-type Filter-mode IP-address Mac-address Vlan
--------- ----------- ----------- --------------- -------------- ---------
fa6/1 ip active 10.0.0.1 10
fa6/1 ip active deny-all 11-20
fa6/2 ip inactive-trust-port
Fa6/3 ip trk active 40.1.1.24 10
Fa6/3 ip trk active 40.1.1.20 10
Fa6/3 ip trk active 40.1.1.21 10
fa6/4 ip-mac active 10.0.0.2 aaaa.bbbb.cccc 10
fa6/4 ip-mac active 11.0.0.1 aaaa.bbbb.cccd 11
fa6/4 ip-mac active deny-all deny-all 12-20
fa6/5 ip-mac active 10.0.0.3 permit-all 10
fa6/5 ip-mac active deny-all permit-all 11-20
Related Commands
show ipc
To display IPC information, use the show ipc command.
show ipc {nodes | ports | queue | status}
Syntax Description
nodes |
Displays the participating nodes. |
ports |
Displays the local IPC ports. |
queue |
Displays the contents of the IPC retransmission queue. |
status |
Displays the status of the local IPC server. |
Defaults
This command has no default settings.
Command Modes
Privileged EXEC mode
Command History
|
|
---|---|
12.1(12c)EW |
Support for this command was introduced on the Catalyst 4500 series switch. |
Examples
This example shows how to display the participating nodes:
Switch#
show ipc nodes
There are 3 nodes in this IPC realm.
ID Type Name Last Last
Sent Heard
10000 Local IPC Master 0 0
2010000 Local GALIOS IPC:Card 1 0 0
2020000 Ethernet GALIOS IPC:Card 2 12 26
Switch#
This example shows how to display the local IPC ports:
Switch#
show ipc ports
There are 11 ports defined.
Port ID Type Name (current/peak/total)
10000.1 unicast IPC Master:Zone
10000.2 unicast IPC Master:Echo
10000.3 unicast IPC Master:Control
10000.4 unicast Remote TTY Server Port
10000.5 unicast GALIOS RF :Active
index = 0 seat_id = 0x2020000 last sent = 0 heard = 1635 0/1/1635
10000.6 unicast GALIOS RED:Active
index = 0 seat_id = 0x2020000 last sent = 0 heard = 2 0/1/2
2020000.3 unicast GALIOS IPC:Card 2:Control
2020000.4 unicast GALIOS RFS :Standby
2020000.5 unicast Slave: Remote TTY Client Port
2020000.6 unicast GALIOS RF :Standby
2020000.7 unicast GALIOS RED:Standby
RPC packets: current/peak/total
0/1/17
Switch#
This example shows how to display the contents of the IPC retransmission queue:
Switch# show ipc queue
There are 0 IPC messages waiting for acknowledgement in the transmit queue.
There are 0 IPC messages waiting for a response.
There are 0 IPC messages waiting for additional fragments.
There are 0 IPC messages currently on the IPC inboundQ.
There are 0 messages currently in use by the system.
Switch#
This example shows how to display the status of the local IPC server:
Switch# show ipc status
IPC System Status:
This processor is the IPC master server.
6000 IPC message headers in cache
3363 messages in, 1680 out, 1660 delivered to local port,
1686 acknowledgements received, 1675 sent,
0 NACKS received, 0 sent,
0 messages dropped on input, 0 messages dropped on output
0 no local port, 0 destination unknown, 0 no transport
0 missing callback or queue, 0 duplicate ACKs, 0 retries,
0 message timeouts.
0 ipc_output failures, 0 mtu failures,
0 msg alloc failed, 0 emer msg alloc failed, 0 no origs for RPC replies
0 pak alloc failed, 0 memd alloc failed
0 no hwq, 1 failed opens, 0 hardware errors
No regular dropping of IPC output packets for test purposes
Switch#
show ipv6 mld snooping
To display IP version 6 (IPv6) Multicast Listener Discovery (MLD) snooping configuration of the switch or the VLAN, use the show ipv6 mld snooping command.
show ipv6 mld snooping [vlan vlan-id]
Syntax Description
vlan vlan-id |
(Optional) Specify a VLAN; the range is 1 to 1001 and 1006 to 4094. |
Command Modes
User EXEC mode
Command History
|
|
---|---|
12.2(40)SG |
This command was introduced on the Catalyst 4500. |
Usage Guidelines
Use this command to display MLD snooping configuration for the switch or for a specific VLAN.
VLAN numbers 1002 through 1005 are reserved for Token Ring and FDDI VLANs and cannot be used in MLD snooping.
Examples
This is an example of output from the show ipv6 mld snooping vlan command. It shows snooping characteristics for a specific VLAN.
Switch>
show ipv6 mld snooping vlan 100
Global MLD Snooping configuration:
-------------------------------------------
MLD snooping : Enabled
MLDv2 snooping (minimal) : Enabled
Listener message suppression : Enabled
TCN solicit query : Disabled
TCN flood query count : 2
Robustness variable : 3
Last listener query count : 2
Last listener query interval : 1000
Vlan 100:
--------
MLD snooping : Disabled
MLDv1 immediate leave : Disabled
Explicit host tracking : Enabled
Multicast router learning mode : pim-dvmrp
Robustness variable : 3
Last listener query count : 2
Last listener query interval : 1000
This is an example of output from the show ipv6 mld snooping command. It displays snooping characteristics for all VLANs on the switch.
Switch
>
show ipv6 mld snooping
Global MLD Snooping configuration:
-------------------------------------------
MLD snooping : Enabled
MLDv2 snooping (minimal) : Enabled
Listener message suppression : Enabled
TCN solicit query : Disabled
TCN flood query count : 2
Robustness variable : 3
Last listener query count : 2
Last listener query interval : 1000
Vlan 1:
--------
MLD snooping : Disabled
MLDv1 immediate leave : Disabled
Explicit host tracking : Enabled
Multicast router learning mode : pim-dvmrp
Robustness variable : 1
Last listener query count : 2
Last listener query interval : 1000
<output truncated>
Vlan 951:
--------
MLD snooping : Disabled
MLDv1 immediate leave : Disabled
Explicit host tracking : Enabled
Multicast router learning mode : pim-dvmrp
Robustness variable : 3
Last listener query count : 2
Last listener query interval : 1000
Related Commands
|
|
---|---|
Enables IP version 6 (IPv6) Multicast Listener Discovery (MLD) snooping globally or on the specified VLAN. |
show ipv6 mld snooping mrouter
To display dynamically learned and manually configured IP version 6 (IPv6) Multicast Listener Discovery (MLD) switch ports for the switch or a VLAN, use the show ipv6 mld snooping mrouter command.
show ipv6 mld snooping mrouter [vlan vlan-id]
Syntax Description
vlan vlan-id |
(Optional) Specify a VLAN; the range is 1 to 1001 and 1006 to 4094. |
Command Modes
User EXEC mode
Command History
|
|
---|---|
12.2(40)SG |
This command was introduced on Catalyst 4500. |
Usage Guidelines
Use this command to display MLD snooping switch ports for the switch or for a specific VLAN.
VLAN numbers 1002 through 1005 are reserved for Token Ring and FDDI VLANs and cannot be used in MLD snooping.
Examples
This is an example of output from the show ipv6 mld snooping mrouter command. It displays snooping characteristics for all VLANs on the switch that are participating in MLD snooping.
Switch> show ipv6 mld snooping mrouter
Vlan ports
---- -----
2 Gi1/0/11(dynamic)
72 Gi1/0/11(dynamic)
200 Gi1/0/11(dynamic)
This is an example of output from the show ipv6 mld snooping mrouter vlan command. It shows multicast switch ports for a specific VLAN.
Switch> show ipv6 mld snooping mrouter vlan 100
Vlan ports
---- -----
2 Gi1/0/11(dynamic)
Related Commands
show ipv6 mld snooping querier
To display IP version 6 (IPv6) Multicast Listener Discovery (MLD) snooping querier-related information most recently received by the switch or the VLAN, use the show ipv6 mld snooping querier command.
show ipv6 mld snooping querier [vlan vlan-id]
Syntax Description
vlan vlan-id |
(Optional) Specify a VLAN; the range is 1 to 1001 and 1006 to 4094. |
Command Modes
User EXEC mode
Command History
|
|
---|---|
12.2(40)SG |
This command was introduced on the Catalyst 4500. |
Usage Guidelines
Use the show ipv6 mld snooping querier command to display the MLD version and IPv6 address of a detected device that sends MLD query messages, which is also called a querier. A subnet can have multiple multicast switches but has only one MLD querier. The querier can be a Layer 3 switch.
The show ipv6 mld snooping querier command output also shows the VLAN and interface on which the querier was detected. If the querier is the switch, the output shows the Port field as Router. If the querier is a router, the output shows the port number on which the querier is learned in the Port field.
The output of the show ipv6 mld snoop querier vlan command displays the information received in response to a query message from an external or internal querier. It does not display user-configured VLAN values, such as the snooping robustness variable on the particular VLAN. This querier information is used only on the MASQ message that is sent by the switch. It does not override the user-configured robustness variable that is used for aging out a member that does not respond to query messages.
VLAN numbers 1002 through 1005 are reserved for Token Ring and FDDI VLANs and cannot be used in MLD snooping.
Examples
This is an example of output from the show ipv6 mld snooping querier command:
Switch>
show ipv6 mld snooping querier
Vlan IP Address MLD Version Port
-------------------------------------------------------------
2 FE80::201:C9FF:FE40:6000 v1 Gi3/0/1
This is an example of output from the show ipv6 mld snooping querier vlan command:
Switch>
show ipv6 mld snooping querier vlan 2
IP address : FE80::201:C9FF:FE40:6000
MLD version : v1
Port : Gi3/0/1
Max response time : 1000s
Related Commands
show issu capability
To display the ISSU capability for a client, use the show issu capability command.
show issu capability {entries | groups | types} [client_id]
Syntax Description
Defaults
This command has no default settings.
Command Modes
User EXEC mode
Command History
|
|
---|---|
12.2(31)SGA |
This command was introduced on the Catalyst 4500 series switch. |
Usage Guidelines
Capability is a functionality that an ISSU client can support and is required to interoperate with peers.
When an ISSU-aware client establishes its session with the peer, an ISSU negotiation takes place. The ISSU infrastructure uses the registered information to negotiate the capabilities and the message version to be used during the session.
Examples
The following example shows how to display the ISSU capability types for the IP host ISSU client (clientid=2082):
Switch#show issu capability types 2082
Client_ID = 2082, Entity_ID = 1 :
Cap_Type = 0
Switch#
The following example shows how to display the ISSU capabilities entries for the IP host ISSU client (clientid=2082):
Switch#show issu capability entries 2082
Client_ID = 2082, Entity_ID = 1 :
Cap_Entry = 1 :
Cap_Type = 0
Switch#
The following example shows how to display the ISSU capabilities groups for the IP host ISSU client (clientid=2082):
Switch#show issu capability groups 2082
Client_ID = 2082, Entity_ID = 1 :
Cap_Group = 1 :
Cap_Entry = 1
Cap_Type = 0
Switch#
Related Commands
|
|
---|---|
Displays the ISSU clients. |
show issu clients
To display the ISSU clients, use the show issu clients command.
show issu clients [peer_uid]
Syntax Description
peer_uid |
(Optional) Displays a list of clients registered to ISSU infrastructure at the peer supervisor engine. |
Defaults
Displays a list of clients registered to the ISSU infrastructure at the supervisor engine where the command is entered.
Command Modes
User EXEC mode
Command History
|
|
---|---|
12.2(31)SGA |
This command was introduced on the Catalyst 4500 series switch. |
Usage Guidelines
To implement ISSU versioning functionality, a client must first register itself, client capability, and client message information with the ISSU infrastructure during the system initialization.
Examples
The following example shows how to display the ISSU clients:
Switch# show issu clients
Client_ID = 2, Client_Name = ISSU Proto client, Entity_Count = 1
Client_ID = 3, Client_Name = ISSU RF, Entity_Count = 1
Client_ID = 4, Client_Name = ISSU CF client, Entity_Count = 1
Client_ID = 5, Client_Name = ISSU Network RF client, Entity_Count = 1
Client_ID = 7, Client_Name = ISSU CONFIG SYNC, Entity_Count = 1
Client_ID = 8, Client_Name = ISSU ifIndex sync, Entity_Count = 1
Client_ID = 9, Client_Name = ISSU IPC client, Entity_Count = 1
Client_ID = 10, Client_Name = ISSU IPC Server client, Entity_Count = 1
Client_ID = 11, Client_Name = ISSU Red Mode Client, Entity_Count = 1
Client_ID = 100, Client_Name = ISSU rfs client, Entity_Count = 1
Client_ID = 110, Client_Name = ISSU ifs client, Entity_Count = 1
Client_ID = 200, Client_Name = ISSU Event Manager client, Entity_Count = 1
Client_ID = 2002, Client_Name = CEF Push ISSU client, Entity_Count = 1
Client_ID = 2003, Client_Name = ISSU XDR client, Entity_Count = 1
Client_ID = 2004, Client_Name = ISSU SNMP client, Entity_Count = 1
Client_ID = 2010, Client_Name = ARP HA, Entity_Count = 1
Client_ID = 2012, Client_Name = ISSU HSRP Client, Entity_Count = 1
Client_ID = 2021, Client_Name = XDR Int Priority ISSU client, Entity_Count = 1
Client_ID = 2022, Client_Name = XDR Proc Priority ISSU client, Entity_Count = 1
Client_ID = 2023, Client_Name = FIB HWIDB ISSU client, Entity_Count = 1
Client_ID = 2024, Client_Name = FIB IDB ISSU client, Entity_Count = 1
Client_ID = 2025, Client_Name = FIB HW subblock ISSU client, Entity_Count = 1
Client_ID = 2026, Client_Name = FIB SW subblock ISSU client, Entity_Count = 1
Client_ID = 2027, Client_Name = Adjacency ISSU client, Entity_Count = 1
Client_ID = 2028, Client_Name = FIB IPV4 ISSU client, Entity_Count = 1
Client_ID = 2054, Client_Name = ISSU process client, Entity_Count = 1
Client_ID = 2058, Client_Name = ISIS ISSU RTR client, Entity_Count = 1
Client_ID = 2059, Client_Name = ISIS ISSU UPD client, Entity_Count = 1
Client_ID = 2067, Client_Name = ISSU PM Client, Entity_Count = 1
Client_ID = 2068, Client_Name = ISSU PAGP_SWITCH Client, Entity_Count = 1
Client_ID = 2070, Client_Name = ISSU Port Security client, Entity_Count = 1
Client_ID = 2071, Client_Name = ISSU Switch VLAN client, Entity_Count = 1
Client_ID = 2072, Client_Name = ISSU dot1x client, Entity_Count = 1
Client_ID = 2073, Client_Name = ISSU STP, Entity_Count = 1
Client_ID = 2077, Client_Name = ISSU STP MSTP, Entity_Count = 1
Client_ID = 2078, Client_Name = ISSU STP IEEE, Entity_Count = 1
Client_ID = 2079, Client_Name = ISSU STP RSTP, Entity_Count = 1
Client_ID = 2081, Client_Name = ISSU DHCP Snooping client, Entity_Count = 1
Client_ID = 2082, Client_Name = ISSU IP Host client, Entity_Count = 1
Client_ID = 2083, Client_Name = ISSU Inline Power client, Entity_Count = 1
Client_ID = 2084, Client_Name = ISSU IGMP Snooping client, Entity_Count = 1
Client_ID = 4001, Client_Name = ISSU C4K Chassis client, Entity_Count = 1
Client_ID = 4002, Client_Name = ISSU C4K Port client, Entity_Count = 1
Client_ID = 4003, Client_Name = ISSU C4K Rkios client, Entity_Count = 1
Client_ID = 4004, Client_Name = ISSU C4K HostMan client, Entity_Count = 1
Client_ID = 4005, Client_Name = ISSU C4k GaliosRedundancy client, Entity_Count = 1
Base Clients:
Client_Name = ISSU Proto client
Client_Name = ISSU RF
Client_Name = ISSU CF client
Client_Name = ISSU Network RF client
Client_Name = ISSU CONFIG SYNC
Client_Name = ISSU ifIndex sync
Client_Name = ISSU IPC client
Client_Name = ISSU IPC Server client
Client_Name = ISSU Red Mode Client
Client_Name = ISSU rfs client
Client_Name = ISSU ifs client
Client_Name = ISSU Event Manager client
Client_Name = CEF Push ISSU client
Client_Name = ISSU XDR client
Client_Name = ARP HA
Client_Name = XDR Int Priority ISSU client
Client_Name = XDR Proc Priority ISSU client
Client_Name = FIB HWIDB ISSU client
Client_Name = FIB IDB ISSU client
Client_Name = FIB HW subblock ISSU client
Client_Name = FIB SW subblock ISSU client
Client_Name = Adjacency ISSU client
Client_Name = FIB IPV4 ISSU client
Client_Name = ISSU process client
Client_Name = ISSU PM Client
Client_Name = ISSU C4K Chassis client
Client_Name = ISSU C4K Port client
Client_Name = ISSU C4K Rkios client
Client_Name = ISSU C4K HostMan client
Client_Name = ISSU C4k GaliosRedundancy client
Related Commands
|
|
---|---|
Displays the ISSU capability for a client. |
|
Displays the ISSU entity information. |
show issu comp-matrix
To display information regarding the In Service Software Upgrade (ISSU) compatibility matrix, use the show issu comp-matrix command.
show issu comp-matrix {negotiated | stored | xml}
Syntax Description
negotiated |
Displays negotiated compatibility matrix information. |
stored |
Displays stored compatibility matrix information. |
xml |
Displays negotiated compatibility matrix information in XML format. |
Defaults
This command has no default settings.
Command Modes
User EXEC mode
Command History
|
|
---|---|
12.2(31)SGA |
This command was introduced on the Catalyst 4500 series switch. |
Usage Guidelines
Before attempting an ISSU, you should know the compatibility level between the old and the new Cisco IOS software versions on the active and the standby-supervisor engines. ISSU will not work if the two versions are incompatible.
The compatibility matrix is available on Cisco.com so that you can also veiw in advance whether an upgrade can be performed with the ISSU process. The compatibility matrix during the ISSU process and later by entering the show issu comp-matrix command. To display information on the negotiation of the compatibility matrix data between two software versions on a given system, use the show issu comp-matrix negotiated command.
Compatibility matrix data is stored with each Cisco IOS software image that supports ISSU capability. To display stored compatibility matrix information, use the show issu comp-matrix stored command.
The compatibility matrix information are built-in any IOS ISSU image. The ISSU infrastructure performs a matrix lookup as soon as the communication with the standby supervisor engine is established. There are three possible results from the lookup operation:
•Compatible—The Base-level system infrastructure and all optional HA-aware subsystems are compatible. In-service upgrade or downgrade between these versions will succeed with minimal service impact.
•Base-Level Compatible—One or more of the optional HA-aware subsystems are not compatible. Although an in-service upgrade or downgrade between these versions will succeed, some subsystems will not be able to maintain their state during the switchover. Prior to attempting an in-service upgrade or downgrade, the impact of this on operation and service of the switch must be considered carefully.
•Incompatible—A set of core system infrastructure must be able to execute in a stateful manner for SSO to function correctly. If any of these "required" features or subsystems is not compatible in two different IOS images, the two versions of the Cisco IOS images are declared "Incompatible". This means that an in-service upgrade or downgrade between these versions is not possible. The systems operates in RPR mode during the period when the versions of IOS at the active and standby supervisor engines differ.
Examples
This example displays negotiated compatibility matrix information:
Switch# show issu comp-matrix negotiated
CardType: WS-C4507R(112), Uid: 2, Image Ver: 12.2(31)SGA
Image Name: cat4500-ENTSERVICES-M
Cid Eid Sid pSid pUid Compatibility
=======================================================
2 1 262151 3 1 COMPATIBLE
3 1 262160 5 1 COMPATIBLE
4 1 262163 9 1 COMPATIBLE
5 1 262186 25 1 COMPATIBLE
7 1 262156 10 1 COMPATIBLE
8 1 262148 7 1 COMPATIBLE
9 1 262155 1 1 COMPATIBLE
10 1 262158 2 1 COMPATIBLE
11 1 262172 6 1 COMPATIBLE
100 1 262166 13 1 COMPATIBLE
110 113 262159 14 1 COMPATIBLE
200 1 262167 24 1 COMPATIBLE
2002 1 - - - UNAVAILABLE
2003 1 262185 23 1 COMPATIBLE
2004 1 262175 16 1 COMPATIBLE
2008 1 262147 26 1 COMPATIBLE
2008 1 262168 27 1 COMPATIBLE
2010 1 262171 32 1 COMPATIBLE
2012 1 262180 31 1 COMPATIBLE
2021 1 262170 41 1 COMPATIBLE
2022 1 262152 42 1 COMPATIBLE
2023 1 - - - UNAVAILABLE
2024 1 - - - UNAVAILABLE
2025 1 - - - UNAVAILABLE
2026 1 - - - UNAVAILABLE
2027 1 - - - UNAVAILABLE
2028 1 - - - UNAVAILABLE
2054 1 262169 8 1 COMPATIBLE
2058 1 262154 29 1 COMPATIBLE
2059 1 262179 30 1 COMPATIBLE
2067 1 262153 12 1 COMPATIBLE
2068 1 196638 40 1 COMPATIBLE
2070 1 262145 21 1 COMPATIBLE
2071 1 262178 11 1 COMPATIBLE
2072 1 262162 28 1 COMPATIBLE
2073 1 262177 33 1 COMPATIBLE
2077 1 262165 35 1 COMPATIBLE
2078 1 196637 34 1 COMPATIBLE
2079 1 262176 36 1 COMPATIBLE
2081 1 262150 37 1 COMPATIBLE
2082 1 262161 39 1 COMPATIBLE
2083 1 262184 20 1 COMPATIBLE
2084 1 262183 38 1 COMPATIBLE
4001 101 262181 17 1 COMPATIBLE
4002 201 262164 18 1 COMPATIBLE
4003 301 262182 19 1 COMPATIBLE
4004 401 262146 22 1 COMPATIBLE
4005 1 262149 4 1 COMPATIBLE
Message group summary:
Cid Eid GrpId Sid pSid pUid Nego Result
=============================================================
2 1 1 262151 3 1 Y
3 1 1 262160 5 1 Y
4 1 1 262163 9 1 Y
5 1 1 262186 25 1 Y
7 1 1 262156 10 1 Y
8 1 1 262148 7 1 Y
9 1 1 262155 1 1 Y
10 1 1 262158 2 1 Y
11 1 1 262172 6 1 Y
100 1 1 262166 13 1 Y
110 113 115 262159 14 1 Y
200 1 1 262167 24 1 Y
2002 1 2 - - - N - did not negotiate
2003 1 1 262185 23 1 Y
2004 1 1 262175 16 1 Y
2008 1 1 262147 26 1 Y
2008 1 2 262168 27 1 Y
2010 1 1 262171 32 1 Y
2012 1 1 262180 31 1 Y
2021 1 1 262170 41 1 Y
2022 1 1 262152 42 1 Y
2023 1 1 - - - N - did not negotiate
2024 1 1 - - - N - did not negotiate
2025 1 1 - - - N - did not negotiate
2026 1 1 - - - N - did not negotiate
2027 1 1 - - - N - did not negotiate
2028 1 1 - - - N - did not negotiate
2054 1 1 262169 8 1 Y
2058 1 1 262154 29 1 Y
2059 1 1 262179 30 1 Y
2067 1 1 262153 12 1 Y
2068 1 1 196638 40 1 Y
2070 1 1 262145 21 1 Y
2071 1 1 262178 11 1 Y
2072 1 1 262162 28 1 Y
2073 1 1 262177 33 1 Y
2077 1 1 262165 35 1 Y
2078 1 1 196637 34 1 Y
2079 1 1 262176 36 1 Y
2081 1 1 262150 37 1 Y
2082 1 1 262161 39 1 Y
2083 1 1 262184 20 1 Y
2084 1 1 262183 38 1 Y
4001 101 1 262181 17 1 Y
4002 201 1 262164 18 1 Y
4003 301 1 262182 19 1 Y
4004 401 1 262146 22 1 Y
4005 1 1 262149 4 1 Y
List of Clients:
Cid Client Name Base/Non-Base
================================================
2 ISSU Proto client Base
3 ISSU RF Base
4 ISSU CF client Base
5 ISSU Network RF client Base
7 ISSU CONFIG SYNC Base
8 ISSU ifIndex sync Base
9 ISSU IPC client Base
10 ISSU IPC Server client Base
11 ISSU Red Mode Client Base
100 ISSU rfs client Base
110 ISSU ifs client Base
200 ISSU Event Manager clientBase
2002 CEF Push ISSU client Base
2003 ISSU XDR client Base
2004 ISSU SNMP client Non-Base
2008 ISSU Tableid Client Base
2010 ARP HA Base
2012 ISSU HSRP Client Non-Base
2021 XDR Int Priority ISSU cliBase
2022 XDR Proc Priority ISSU clBase
2023 FIB HWIDB ISSU client Base
2024 FIB IDB ISSU client Base
2025 FIB HW subblock ISSU clieBase
2026 FIB SW subblock ISSU clieBase
2027 Adjacency ISSU client Base
2028 FIB IPV4 ISSU client Base
2054 ISSU process client Base
2058 ISIS ISSU RTR client Non-Base
2059 ISIS ISSU UPD client Non-Base
2067 ISSU PM Client Base
2068 ISSU PAGP_SWITCH Client Non-Base
2070 ISSU Port Security clientNon-Base
2071 ISSU Switch VLAN client Non-Base
2072 ISSU dot1x client Non-Base
2073 ISSU STP Non-Base
2077 ISSU STP MSTP Non-Base
2078 ISSU STP IEEE Non-Base
2079 ISSU STP RSTP Non-Base
2081 ISSU DHCP Snooping clientNon-Base
2082 ISSU IP Host client Non-Base
2083 ISSU Inline Power client Non-Base
2084 ISSU IGMP Snooping clientNon-Base
4001 ISSU C4K Chassis client Base
4002 ISSU C4K Port client Base
4003 ISSU C4K Rkios client Base
4004 ISSU C4K HostMan client Base
4005 ISSU C4k GaliosRedundancyBase
This example displays stored compatibility matrix information:
Switch> show issu comp-matrix stored
Number of Matrices in Table = 1
(1) Matrix for cat4500-ENTSERVICES-M(112) - cat4500-ENTSERVICES-M(112)
==========================================
Start Flag (0xDEADBABE)
My Image ver: 12.2(31)SGA
Peer Version Compatibility
------------ -------------
12.2(31)SGA Comp(3)
Related Commands
|
|
---|---|
Displays the ISSU clients. |
|
Displays ISSU session information for a specified client. |
show issu endpoints
To display the ISSU endpoint information, use the show issu endpoints command.
show issu endpoints
Syntax Description
This command has no arguments or keywords
Defaults
This command has no default settings.
Command Modes
User EXEC mode
Command History
|
|
---|---|
12.2(31)SGA |
This command was introduced on the Catalyst 4500 series switch. |
Usage Guidelines
Endpoint is an execution unit within a redundancy domain. There are only 2 endpoints on the Catalyst 4500 series switch redundant chassis: 1 and 2; they correspond to the slot numbers for the supervisor engine. The ISSU infrastructure communicates between these two endpoints to establish session and to perform session negotiation for ISSU clients.
Examples
The following example shows how to display the ISSU endpoints:
Switch# show issu endpoints
My_Unique_ID = 1/0x1, Client_Count = 46
This endpoint communicates with 1 peer endpoints :
Peer_Unique_ID CAP VER XFORM ERP Compatibility
2/0x2 1 1 1 1 Same
Shared Negotiation Session Info :
Nego_Session_ID = 15
Nego_Session_Name = shared nego session
Transport_Mtu = 4096
Ses_In_Use = 2
Switch#
Related Commands
|
|
---|---|
Displays the ISSU clients. |
show issu entities
To display the ISSU entity information, use the show issu entities command.
show issu entities [client_id]
Syntax Description
client_id |
(Optional) ISSU client ID. |
Defaults
This command has no default settings.
Command Modes
User EXEC mode
Command History
|
|
---|---|
12.2(31)SGA |
This command was introduced on the Catalyst 4500 series switch. |
Usage Guidelines
Entity is a logical group of sessions with some common attributes (like capability list and message type). Currently, most ISSU clients on the Catalyst 4500 series switch have only one entity.
Examples
The following example shows how to display the entity information for a specified ISSU client:
Switch#show issu entities 2072
Client_ID = 2072 :
Entity_ID = 1, Entity_Name = ISSU dot1x entity :
MsgType MsgGroup CapType CapEntry CapGroup
Count Count Count count Count
28 1 1 1 1
Switch#
Related Commands
|
|
---|---|
Displays the ISSU clients. |
show issu fsm
Note This command is not intended for end-users.
To display the ISSU finite state machine (FSM) information corresponding to an ISSU session, use the show issu fsm command.
show issu fsm [session_id]
Syntax Description
session_id |
(Optional) Provides detailed information about the FSM for the specified session. |
Defaults
This command has no default settings.
Command Modes
User EXEC mode
Command History
|
|
---|---|
12.2(31)SGA |
This command was introduced on the Catalyst 4500 series switch. |
Examples
The following example displays and verifies the ISSU state after LOADVERSION:
Switch# show issu fsm 26
Session_ID = 26 :
FSM_Name Curr_State Old_State Error_Reason
FSM_L1 TRANS A_VER none
FSM_L2_HELLO EXIT RCVD none
FSM_L2_A_CAP A_EXIT A_RSP none
FSM_L2_P_CAP P_INIT unknown none
FSM_L2_A_VER A_EXIT A_RES_RSP none
FSM_L2_P_VER P_INIT unknown none
FSM_L2_TRANS COMP COMP none
Current FSM is FSM_L2_TRANS
Session is compatible
Negotiation started at 00:01:07.688, duration is 0.148 seconds
Switch#
Related Commands
|
|
---|---|
Displays the ISSU clients. |
|
Displays ISSU session information for a specified client. |
show issu message
To display checkpoint messages for a specified ISSU client, use the show issu message command.
show issu message {groups | types} [client_id]
Syntax Description
Defaults
If client ID is not specified, displays message groups or message types information for all clients registered to the ISSU infrastructure.
Command Modes
User EXEC mode
Command History
|
|
---|---|
12.2(31)SGA |
This command was introduced on the Catalyst 4500 series switch. |
Usage Guidelines
Messages are sync-data (also known as checkpoint data) sent between two endpoints
When an ISSU-aware client establishes its session with a peer, an ISSU negotiation takes place. The ISSU infrastructure uses the registered information to negotiate the capabilities and the message version to be used during the session.
Examples
The following example shows how to display the message groups for Client_id 2082:
Switch#show issu message groups 2082
Client_ID = 2082, Entity_ID = 1 :
Message_Group = 1 :
Message_Type = 1, Version_Range = 1 ~ 2
Message_Type = 2, Version_Range = 1 ~ 2
Switch#
The following example shows how to display the message types for Client_id 2082:
Switch#show issu message types 2082
Client_ID = 2082, Entity_ID = 1 :
Message_Type = 1, Version_Range = 1 ~ 2
Message_Ver = 1, Message_Mtu = 12
Message_Ver = 2, Message_Mtu = 8
Message_Type = 2, Version_Range = 1 ~ 2
Message_Ver = 1, Message_Mtu = 32
Message_Ver = 2, Message_Mtu = 28
Switch#
Related Commands
|
|
---|---|
Displays the ISSU clients. |
show issu negotiated
To display the negotiated capability and message version information of the ISSU clients, use the
show issu negotiated command.
show issu negotiated {capability | version} [session_id]
Syntax Description
Defaults
Displays negotiated capability or version information for all ISSU sessions.
Command Modes
User EXEC mode
Command History
|
|
---|---|
12.2(31)SGA |
This command was introduced on the Catalyst 4500 series switch. |
Examples
The following example shows how to display the message types for a specific group:
Switch# show issu negotiated capability 26
Session_ID = 26 :
Cap_Type = 0, Cap_Result = 1 No cap value assigned
Switch# show issu negotiated version 26
Session_ID = 26 :
Message_Type = 1, Negotiated_Version = 1, Message_MTU = 44
Message_Type = 2, Negotiated_Version = 1, Message_MTU = 4
Related Commands
|
|
---|---|
Displays ISSU session information for a specified client. |
show issu rollback-timer
To display ISSU rollback-timer status, use the show issu rollback-timer command.
show issu rollback-timer
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Priviledged EXEC mode
Command History
|
|
---|---|
12.2(31)SGA |
This command was introduced on the Catalyst 4500 series switch. |
Examples
The following example shows how to display the rollback-timer status:
Switch#show issu rollback-timer
Rollback Process State = Not in progress
Configured Rollback Time = 45:00
Switch#
Related Commands
show issu sessions
To display ISSU session information for a specified client, use the show issu sessions command.
show issu sessions [client_id]
Syntax Description
client_id |
(Optional) Specifies the ISSU client ID. |
Defaults
Displays session information for all clients registered to the ISSU infrastructure.
Command Modes
User EXEC mode
Command History
|
|
---|---|
12.2(31)SGA |
This command was introduced on the Catalyst 4500 series switch. |
Usage Guidelines
Session is bidirectional and a reliable connection is established between two endpoints. Sync-data and negotiation messages are sent to the peer endpoint through a session. On a Catalyst 4500 series switch, each ISSU-aware client has a maximum of one session at each endpoint.
When an ISSU-aware client establishes its session with the peer, an ISSU negotiation takes place. The ISSU infrastructure uses the registered information to negotiate the capabilities and the message version to be used during the session.
Examples
The following example shows how to display the rollback-timer status:
Switch#show issu sessions 2072
Client_ID = 2072, Entity_ID = 1 :
*** Session_ID = 26, Session_Name = dot1x :
Peer Peer Negotiate Negotiated Cap Msg Session
UniqueID Sid Role Result GroupID GroupID Signature
2 26 PRIMARY COMPATIBLE 1 1 0
(no policy)
Negotiation Session Info for This Message Session:
Nego_Session_ID = 26
Nego_Session_Name = dot1x
Transport_Mtu = 17884
Switch#
Related Commands
|
|
---|---|
Displays the ISSU clients. |
show issu state
To display the ISSU state and current booted image name during the ISSU process, use the
show issu state command.
show issu state [slot_number] [detail]
Syntax Description
|