- Preface
- Overview
- Using the Command-Line Interface
- Assigning the Switch IP Address and Default Gateway
- Configuring Cisco IOS Configuration Engine
- Administering the Switch
- Configuring Web-Based Authentication
- Configuring Cisco TrustSec
- Clustering Switches
- Managing Switch Stacks
- Configuring SDM Templates
- Configuring Switch-Based Authentication
- Configuring IEEE 802.1x Port-Based Authentication
- Configuring Interface Characteristics
- Configuring VLANs
- Configuring VTP
- Configuring Voice VLAN
- Configuring STP
- Configuring MSTP
- Configuring Optional Spanning-Tree Features
- Configuring Flex Links and the MAC Address-Table Move Update Feature
- Configuring DHCP Features and IP Source Guard
- Configuring Dynamic ARP Inspection
- Configuring IGMP Snooping and MVR
- Configuring Port-Based Traffic Control
- Configuring UDLD
- Configuring CDP
- Configuring LLDP, LLDP-MED, and Wired Location Service
- Configuring SPAN and RSPAN
- Configuring RMON
- Configuring System Message Logging and Smart Logging
- Configuring Cisco IOS IP SLAs Operations
- Configuring SNMP
- Configuring Network Security with ACLs
- Configuring QoS
- Configuring Static IP Routing
- Configuring IPv6 Routing
- Configuring IPv6 MLD Snooping
- Configuring IPv6 ACLs
- Configuring EtherChannels and Link-State Tracking
- Troubleshooting
- Configuring Online Diagnostics
- Working with the Cisco IOS File System, Configuration Files, and Software Images
- Unsupported Commands in Cisco IOS Release 15.0(2)SE
- Recommendations for Upgrading a Catalyst 2950 Switch to a Catalyst 2960 Switch
- Index
Unsupported Commands in Cisco IOS Release 15.0(2)SE and Later
This appendix lists some of the command-line interface (CLI) commands that appear when you enter the question mark (?) at the Catalyst 2960, 2960-S, or 2960-C switch prompt but are not supported in this release, either because they are not tested or because of switch hardware limitations. This is not a complete list. These unsupported commands are listed by software feature and command mode:
Access Control Lists
Unsupported Privileged EXEC Commands
access-enable [ host ] [ timeout minutes ]
access-template [ access-list-number | name ] [ dynamic-name ] [ source ] [ destination ] [ timeout minutes ]
clear access-template [ access-list-number | name ] [ dynamic-name ] [ source ] [ destination ].
show access-lists rate-limit [ destination ]
show ip accounting [ checkpoint ] [ output-packets | access violations ]
Unsupported Global Configuration Commands
access-list rate-limit acl-index { precedence | mask prec-mask }
Unsupported Route-Map Configuration Commands
match ip address prefix-list prefix-list-name [ prefix-list-name...]
Boot Loader Commands
Unsupported Global Configuration Commands
Embedded Syslog Manager
Unsupported Global Configuration Commands
Unsupported Privileged EXEC Commands
IGMP Snooping Commands
Unsupported Global Configuration Commands
Interface Commands
Unsupported Privileged EXEC Commands
show interfaces [ interface-id | vlan vlan-id ] [ crb | fair-queue | irb | mac-accounting | precedence | irb | random-detect | rate-limit | shape ]
Unsupported Global Configuration Commands
Unsupported Interface Configuration Commands
MAC Address Commands
Unsupported Privileged EXEC Commands
show mac-address-table address
show mac-address-table aging-time
show mac-address-table dynamic
show mac-address-table interface
show mac-address-table multicast
show mac-address-table notification
show mac address-table multicast
Note Use the show ip igmp snooping groups privileged EXEC command to display Layer 2 multicast address-table entries for a VLAN.
Unsupported Global Configuration Commands
Miscellaneous
Unsupported User EXEC Commands
Unsupported Privileged EXEC Commands
Unsupported Global Configuration Commands
errdisable recovery cause unicast flood
Network Address Translation (NAT) Commands
Unsupported Privileged EXEC Commands
QoS
Unsupported Global Configuration Command
Unsupported Interface Configuration Commands
Unsupported Policy-Map Configuration Command
class class-default where class-default is the class-map-name.
RADIUS
Unsupported Global Configuration Commands
aaa authentication feature default enable
aaa authentication feature default line
authentication command bounce-port ignore (only on switches running the LAN Lite image)
authentication command disable-port ignore (only on switches running the LAN Lite image)
SNMP
Unsupported Global Configuration Commands
no monitor session all (only on switches running the LAN Lite image)
snmp-server enable traps rtr (only on switches running the LAN Lite image)
logging discriminator discr-name [[ facility ] [ mnemonics ] [ msg-body ] { drops string | includes string }] [ severity { drops sev-num | includes sev-num }] [ rate-limit msglimit ]
SNMPv3
Unsupported 3DES Encryption Commands
Spanning Tree
Unsupported Global Configuration Command
Unsupported Interface Configuration Command
VLAN
Unsupported Global Configuration Command
Unsupported vlan-config Command
Unsupported User EXEC Commands
Unsupported vlan-config Command
Unsupported VLAN Database Commands
VTP
Unsupported Privileged EXEC Commands
vtp { password password | pruning | version number }
Note This command has been replaced by the vtp global configuration command.