Error
Message:
Pre-Upgrade check
failed.
Return code 0x40930062 (free space in the filesystem is below
threshold).
|
This error
indicates that there is not enough space in the
/var/sysmgr partition.
|
Reboot the
system.
|
Error
message:
Pre-Upgrade check failed. Return code 0x4093000A (SRG collection
failed)
|
A module is
removed during the upgrade.
|
- Make sure that the module
removal is complete.
- Restart the software upgrade
using the instructions in the
Cisco Nexus 1000V Installation and Upgrade Guide.
|
Error
message:
Pre-Upgrade check failed. Return code 0x40930076 (Standby sup is
offline. ISSU will not proceed)
|
The standby
VSM is not present or is not synchronized with the active VSM, and the VSMs do
not form a stable HA pair.
|
- Verify the HA
synchronization state.
show system redundancy status
The
output of this command must indicate the following:
Active VSM: Active with HA standby
Standby VSM: HA standby
- If the output of the
show system redundancy status command indicates that
the VSMs are not synchronized, see
Problems with High Availability.
- When the VSMs are
synchronized, restart the software upgrade using the detailed instructions in
the
Cisco
Nexus 1000V Installation and Upgrade Guide.
|
Error
message:
Pre-Upgrade check failed. Return code 0x807B0002 (No such file
or directory)
Error
message:
Pre-Upgrade check failed.
Return code 0x4093000F (Failed to copy image)
|
The
software image files required for the upgrade are not present or were not
copied to the
bootflash: repository.
There may
not be enough room in the
bootflash: repository for the files to be copied.
|
- Verify that there is enough
space in bootflash for the image files.
dir
- Do one of the following:
- If additional space is
needed, delete other files from the
bootflash: repository to make room for the software
image files.
delete
Caution
|
Do not delete kickstart or system image files from bootflash. If there are no
image files in bootflash, the system cannot reboot if required.
|
- If not, continue with the
next step.
- Download the required images
from
www.cisco.com to
the
bootflash: repository.
- Verify that the correct
images are in the
bootflash: repository.
show boot
- When the correct software
images are in the
bootflash: repository, restart the
software upgrade using the instructions in the
Cisco
Nexus 1000V Installation and Upgrade Guide.
|
The
install command fails with the following error:
Return code 0x4045001F
(image MD5 checksum error)
Pre-Upgrade check failed.
Return code 0x40930011 (Image verification failed)
|
The
software image file(s) required for the upgrade do not pass the MD5 checksum
verification, indicating that the correct file(s) are not present in
bootflash: repository for the upgrade to proceed.
A file
can be truncated when copied.
|
- Using the README file from
the upgrade zip folder at
www.cisco.com, verify
the MD5 checksum for each of the image files.
show file bootflash: filename md5sum
- Replace the file(s) that
do not match.
- Verify that the correct
images are in the
bootflash: repository and that the checksums match.
show file bootflash: filename md5sum
- When the correct software
images are in the
bootflash: repository, restart the software upgrade
using the instructions in the
Cisco Nexus 1000V Installation and Upgrade Guide.
|
Error
message:
Install has failed. Return
code 0x40970001 (Incompatible image)
|
You might
have used an incorrect filename when entering the
install all command.
|
Restart
the software upgrade using the correct filenames for new software images.
install all kickstart
filename1
system
filename2
|
After
upgrading, the VSMs are not running the new software version.
|
The boot
variables were not set properly.
|
- Verify that the running
images and boot variables match the upgrade version.
show version
show boot
- If needed, download the
required images from
www.cisco.com to your
local
bootflash: repository.
- Verify that the correct
images are in the
bootflash: repository.
show boot
- Restart the software
upgrade using the instructions in the
Cisco Nexus 1000V Installation and Upgrade Guide.
- If the problem persists,
collect details of the upgrade and open a support case.
show system internal log
install details
|
Performing the configuration copy process fails and stops the upgrade.
Performing configuration
copy.
[####------------]
30%
|
Service
or system errors.
|
- Manually copy the
configuration.
copy running-config
startup-config
- Do one of the following:
|
Error
message:
Another install procedure may be in progress.
(0x401E0007)
|
Another
upgrade session is in progress from a VSM console or SSH/Telnet.
|
Do one of
the following:
- Continue the first upgrade
session in progress.
- Stop the upgrade and
restart one session only using the instructions in the
Cisco Nexus 1000V Installation and Upgrade Guide.
|
The
install command fails with following error message:
-- FAIL. Return code
0x4093001E (Standby failed to come online)
Install has failed. Return
code 0x4093001E (Standby failed to come online)
|
The
standby VSM fails to boot with the new image.
|
Do one of
the following:
|
The
install command fails with following error message:
Install has failed. Return code 0x4093001F (Standby installer failed to take over the installation).
Please identify the cause of the failure, and try “install all” again”
|
The
standby VSM takes more than 10 minutes to come up and form a stable HA pair
with the active VSM.
|
- Reset the boot variables
to the original filenames.
boot kickstart filename
sup-1
sup-2
- If the standby is still
running the new software version, reload it.
reload
The
standby synchronizes with the active, so that both are running the original
software version.
|
The
install command fails with following error message:
Module 2: Waiting for
module online. -- SUCCESS -- Install has failed. Return code 0x40930000
(Current operation failed to complete within specified time)
|
A failure
at the standby VSM caused it to reload again after the
Continuing with installation, please wait message and
before the switchover.
|
- Inspect the logs.
show logging
- Look for standby reloads
caused by process failures.
show cores
If a
process crash is observed, collect details of the upgrade and open a support
case.
show system internal log
install details
-
Restart the software upgrade using the instructions in the
Cisco Nexus 1000V Installation and Upgrade Guide.
|