Release Notes for Cisco NCS 4000 Series, Cisco IOS XR Release 6.1.1.2
The release notes contain information about the new features introduced in the Cisco NCS 4000 Series. For detailed information regarding features, capabilities, hardware, and software introduced with this release, see the guides listed in the Additional References section.
Revision History
Date | Notes |
October 2016 | This is the first release of this publication. |
November 2016 |
Added a section on supported FPD versions. |
Software and Hardware Requirements
Before you begin to install the software, you must check whether your system meets the minimum software and hardware requirements.
-
Hardware—Intel Core i5, i7, or faster processor. A minimum of 4 GB RAM, 100 GB hard disk with 250 MB of available hard drive space.
-
One of these operating System:
-
Windows 7, Windows Server 2008, or later.
-
Apple Mac OS X
-
UNIX workstation with Solaris Version 9 or 10 on an UltraSPARC-III or faster processor, with a minimum of 1 GB RAM and a minimum of 250 MB of available hard drive space.
-
Ubuntu 12.10
-
-
Java Runtime Environment—Java Runtime Environment Version 1.8.
-
Browser:
-
Internet Explorer
-
Mozilla
-
Safari
-
Google Chrome
-
External Caveats
External Bugs in Release 6.1.1.2
Release 6.1.1.2 addresses the following external caveats:
-
CSCva93006: GMPLS Tunnel down after SU from 602 to 6112 14C.
-
CSCvb03651: ISSU downgrade button is not enabled after activation of standby RP, so activation of Active RP wasn't possible from CTC
-
CSCvb14468: TCM TIM stuck on NNI controller at tail after applying SNC-S profile.
-
CSCvb28819: CTC getting hang for 10-15 min after LCVMSO/RPVMSO.
-
CSCuz56046: Circuit diversity dropdown does not list all the tunnels after the hot Swap of NCS4K-2H10T-OP-KS card.
-
CSCva93152: NCS4016-FC2-M CCC-FPGA downgrade from 612_7C to 602_19C failed.
-
CSCvb20447: Incomplete circuit map in Edit Circuit tab after the OIR or shut down of the route processor card.
-
CSCvb20474: BO Lane Wise raised TCA do no show Lane number for very first Lane.
-
CSCvb24367: Pluggables are not updated after the line card recovery by reloading after OIR of the fan tray.
-
CSCvb28786: Protect path is not shown in Edit circuit detailed map for BO circuit.
-
CSCvb29090: Controller is not created at OTU level. Delete or create after loop back configuration.
-
CSCvb32597: Delay in response for Checkbox of inactive packages on System pane.
-
CSCvb59248: 0/FT0 was removed and reinstalled and the "FPD-NEED-UPGRADE" alarm was raised.
Supported FPD Versions
The following table lists the FPD versions supported in Release 6.1.1.2.
Card Type | FPD Description | Req. Reload | S/W Version | Min. Req. S/W Version | Min. Req. Board Version |
NCS4009-FC-S |
CCC-FPGA(A) CCC-Power-On(A) PLX-8608(A) SB Certificates(A) |
No No Yes No |
1.05 1.03 0.03 1.00 |
1.05 1.03 0.03 1.00 |
0.1 0.1 0.1 0.0 |
NCS4009-FC2-S |
CCC-FPGA(A) CCC-Power-On(A) PLX-8608(A) SB Certificates(A) |
No No Yes No |
1.11 1.01 0.03 1.00 |
1.11 1.01 0.03 1.00 |
0.1 0.1 0.1 0.0 |
NCS4016-FC-M |
CCC-FPGA(A) CCC-Power-On(A) PLX-8649(A) SB Certificates(A) |
No No Yes No |
4.40 1.12 0.08 1.00 |
4.40 1.12 0.08 1.00 |
0.1 0.1 0.1 0.0 |
NCS4016-FC-S |
CCC-FPGA(A) CCC-Power-On(A) PLX-8649(A) SB Certificates(A) CCC-FPGA(A) CCC-Power-On(A) PLX-8649(A) SB Certificates(A) |
Yes Yes Yes No No No Yes No |
0.05 1.12 0.08 1.00 5.07 1.01 0.08 1.00 |
0.01 1.08 0.08 1.00 5.07 1.01 0.08 1.00 |
0.1 0.1 0.1 0.0 0.1 0.1 0.1 0.0 |
NCS4009-FC2-M |
CCC-FPGA(A) CCC-Power-On(A) PLX-8649(A) SB Certificates(A) |
No No Yes No |
1.16 1.01 0.11 1.00 |
1.16 1.01 0.11 1.00 |
0.1 0.1 0.1 0.0 |
NCS4K-2OT-O-S |
Backup-ZYNQ CCC-FPGA(A) CCC-Power-On(A) DIGI1 DIGI2 Ethernet Switch(A) GENNUM PLX-8618(A) Primary-ZYNQ SB Certificates(A) |
Yes No No No No Yes No Yes No No |
1.68 3.27 1.17 2.03 2.03 1.40 3.01 0.09 1.68 1.00 |
1.00 3.27 1.17 2.03 2.03 1.40 3.01 0.09 1.68 1.00 |
0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.0 |
NCS4K-2OT-OP-S |
CCC-FPGA(A) CCC-Power-On(A) Ethernet Switch(A) PLX-8632(A) SB Certificates(A) |
No No Yes Yes No |
1.10 1.06 1.02 1.00 1.00 |
1.10 1.06 1.02 1.00 1.00 |
0.1 0.1 0.1 0.1 0.0 |
NCS4K-2OT-OP-S |
DIGI1 DIGI2 Primary-ZYNQ |
No No No |
2.03 2.03 1.01 |
2.03 2.03 1.01 |
0.1 0.1 0.1 |
NCS4K-24LR-O-S |
Backup-ZYNQ CCC-FPGA(A) CCC-Power-On(A) Ethernet Switch(A) PLX-8618(A) Primary-ZYNQ SB Certificates(A) |
Yes No No Yes Yes No No |
4.15 4.39 1.17 1.37 0.10 4.17 1.00 |
0.01 4.39 1.17 1.37 0.10 4.17 1.00 |
0.1 0.1 0.1 0.1 0.1 0.0 0.0 |
NCS4K-2H-O-K |
Backup-ZYNQ CCC-FPGA(A) CCC-Power-On(A) DIGI1 DIGI2 Ethernet Switch(A) GENNUM LEPTON PLX-8618(A) Primary-ZYNQ SB Certificates(A) |
Yes No No No No Yes No No Yes No No |
1.55 3.38 1.17 2.03 2.03 1.40 3.01 4.02 0.10 1.56 1.00 |
0.01 3.38 1.17 2.03 2.03 1.40 3.01 4.02 0.10 1.56 1.00 |
0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.0 |
NCS4K-2H-W |
Backup-ZYNQ CCC-FPGA(A) CCC-Power-On(A) EAGLE-0-FPD EAGLE-1-FPD Ethernet Switch(A) GN2411-FPD-1 GN2411-FPD-2 GN2411-FPD-3 GN2411-FPD-4 PLX-8608(A) Primary-ZYNQ SB Certificates(A) |
No No No No No Yes Yes Yes Yes Yes Yes No No |
1.53 4.30 1.16 5.05 5.05 1.35 3.05 3.05 3.05 3.05 0.10 1.53 1.00 |
1.00 4.30 1.16 5.05 5.05 1.35 3.05 3.05 3.05 3.05 0.10 1.53 1.00 |
0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.0 |
NCS4K-2H10T-OP-KS |
Backup-ZYNQ CCC-FPGA(A) CCC-Power-On(A) DIGI1 DIGI2 Ethernet Switch(A) GRIMA PLX-8649(A) Primary-ZYNQ SB Certificates(A) |
Yes No No No No Yes Yes Yes No No |
1.75 1.44 1.08 2.03 2.03 1.02 1.35 0.07 1.75 1.00 |
1.00 1.44 1.08 2.03 2.03 1.02 1.35 0.07 1.75 1.00 |
0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.0 |
NCS4K-4H-OP-K |
Backup-ZYNQ CCC-FPGA(A) CCC-Power-On(A) DIGI1 DIGI2 Ethernet Switch(A) LEPTON PLX-8649(A) Primary-ZYNQ SB Certificates(A) |
Yes Yes Yes No No Yes No Yes No No |
0.09 2.02 1.06 2.03 2.03 1.01 5.00 0.01 1.09 1.00 |
0.09 2.02 1.06 2.03 2.03 1.01 5.00 0.01 1.09 1.00 |
0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.0 |
NCS4K-AC-PSU |
AB-PriMCU(A) AB-Sec54vMCU(A) AB-Sec5vMCU(A) DT-PriMCU(A) DT-PriMCU(A) DT-PriMCU(A) DT-Sec54vMCU(A) DT-Sec54vMCU(A) DT-Sec54vMCU(A) DT-Sec54vMCU(A) DT-Sec54MCU(A) DT-Sec5vMCU(A) |
No No No No No No No No No No No Yes |
1.31 1.49 1.43 3.00 1.06 2.01 4.00 2.03 3.02 3.01 1.09 2.02 |
1.31 1.49 1.43 3.00 1.06 2.01 4.00 2.03 3.02 3.01 1.09 2.02 |
0.1 0.1 0.1 1.0 0.2 0.3 1.0 0.2 0.3 1.0 0.2 0.3 |
NCS4K-CRAFT |
Craft-NCS4009(A) Craft-NCS4016(A) |
No No |
1.03 1.04 |
1.03 1.04 |
0.1 0.1 |
NCS4K-DC-PSU-V1 |
AB-PriMCU(A) AB-Sec54vMCU(A) AB-Sec5vMCU(A) DT-Pri2MCU(A) DT-Pri2MCU(A) DT-PriMCU(A) DT-PriMCU(A) DT-Sec54v2MCU(A) DT-Sec54v2MCU(A) DT-Sec54vMCU(A) DT-Sec54vMCU(A) DT-Sec54MCU(A) DT-Sec5vMCU(A) |
No No No No No No No No No No No No No |
1.26 1.41 1.52 3.02 2.02 3.02 2.02 3.01 2.05 3.01 2.05 3.04 2.06 |
1.26 1.41 1.52 3.02 2.02 3.02 2.02 3.00 2.05 3.00 2.05 3.02 2.06 |
0.1 0.1 0.1 1.0 0.2 1.0 0.2 1.0 0.2 1.0 0.2 1.0 0.2 |
NCS4K-ECU |
ECU-FPGA(A) |
No |
3.01 |
3.01 |
0.1 |
NCS4K-FTA |
Fantray-FPGA(A) |
No |
3.01 |
3.01 |
0.1 |
NCS4K-RP |
BACKUP-BIOS(A) Backup-CCC-PwrOn(A) Backup-Ethswitch(A) Backup-Timing(A) BP-FPGA(A) CCC-Bootloader CCC-FPGA(A) CCC-Power-On(A) CPU-Complex-Bckkey(A) CPU-Complex-Boot(A) CPU-Complex-FPGA(A) CPU-Complex-Prikey(A) Ethernet Switch(A) PLX-8649(A) PLX-8696(A) Primary-BIOS(A) SB Backup(A) SB Certificates(A) SB Primary Key(A) Timing FPGA(A) |
Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No No Yes |
14.02 1.19 1.36 3.49 3.17 4.21 4.21 1.19 1.00 2.04 2.04 1.00 1.36 0.08 0.05 14.03 1.00 1.00 1.00 3.49 |
1.00 1.00 1.00 3.00 3.17 4.21 4.21 1.19 1.00 2.04 2.04 1.00 1.36 0.08 0.05 14.03 1.00 1.00 1.00 3.49 |
0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.0 0.0 0.0 0.1 |
P-S-FANTRAY |
Fantray-FPGA(A) |
No |
2.04 |
2.04 |
0.2 |
Cisco Bug Search Tool
Use the Bug Search Tool (BST) to view the list of outstanding and resolved bugs in a release.
BST, the online successor to Bug Toolkit, is designed to improve the effectiveness in network risk management and device troubleshooting. The tool allows partners and customers to search for software bugs based on product, release, and keyword, and aggregates key data such as bug details, product, and version. The tool has provision to filter bugs based on credentials to provide external and internal bug views for the search input.
Search Bugs in BST
Procedure
Step 1 |
Go to https://bst.cloudapps.cisco.com/bugsearch. You will be prompted to log into Cisco.com. After successful login, the Bug Toolkit page open. |
Step 2 |
Enter the bug ID in the Search For: field. To search for release bugs, enter the following parameters in the page:
|
Step 3 |
Press Enter.
|
Additional References
Related Documentation
Use the release notes with the following publications:
Document Title |
Description |
---|---|
Hardware Installation Guide for Cisco NCS 4000 Series |
Provides installation information about the Cisco NCS 4009 and Cisco NCS 4016 chassis. |
Cisco Network Convergence System 4000 Series Unpacking, Moving, and Securing Guide |
Provides instructions for unpacking the Cisco NCS 4009 and Cisco NCS 4016 chassis, moving the chassis to its permanent location, and mounting the chassis in a rack. |
Regulatory Compliance and Safety Information for the Cisco NCS 4000 Series |
Provides the international agency compliance, safety, and statutory information that apply to Cisco NCS 4009 and Cisco NCS 4016 chassis. |
Configuration Guide for Cisco NCS 4000 Series |
Provides background and reference material, procedures to configure and maintain the Cisco NCS 4009 and Cisco NCS 4016 chassis. |
Command Reference for Cisco NCS 4000 Series |
Provides the various commands available to configure and maintain the Cisco NCS 4009 and Cisco NCS 4016 chassis. |
System Setup and Software Installation Guide for Cisco NCS 4000 Series |
Provides instructions to set up the system and perform software installation. |
Alarms Troubleshooting Guide for Cisco NCS 4000 Series |
Provides a description, severity, and troubleshooting procedure for each commonly encountered NCS 4000 alarm and condition. |
Cisco IOS XR System Error Message Reference Guide |
Provides a list of the Cisco IOS XR system error messages for all Cisco IOS XR platforms |
Quality of Service Configuration Guide for Cisco NCS 4000 Series |
Provides features available to configure and maintain Quality of Service (QoS) for the Cisco NCS 4000 Series Routers. |
Quality of Service Command Reference for Cisco NCS 4000 Series |
Provides various commands available to configure and maintain Quality of Service (QoS) for the Cisco NCS 4000 Series Routers. |
Migration of Single Chassis to Multi Chassis for Cisco NCS 4000 Series |
Provides configuration procedures for the supported multi chassis configurations. |
Technical Assistance
Link | Description |
http://www.cisco.com/cisco/web/support/index.html |
The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies. To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds Access to most tools on the Cisco Support website requires a Cisco.com user ID and password. |