Cisco ONS 15454 and Cisco ONS 15327 TL1 Command Quick Reference Guide, Release 4.0

Table Of Contents

Cisco ONS 15454 and Cisco ONS 15327 TL1 Command Quick Reference Guide, Release 4.0

BLSR

Cross Connections

DWDM (Cisco ONS 15454 only)

Environment Alarms and Controls

Equipment

Fault

IOS

Log

Network

Performance

Ports

Security

SONET Line Protection

Software Download

STS and VT Paths

Synchronization

System

Test Access

Testing

UCP

Path Protection Configuration Switching

Quick Reference

Cisco ONS 15454 and Cisco ONS 15327 TL1 Command Quick Reference Guide, Release 4.0

---

---

Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration. Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's path protection feature, which may be used in any topological network configuration. Cisco does not recommend using its path protection feature in any particular topological network configuration.

---

This guide lists TL1 commands and autonomous messages by category. It includes basic descriptions and input and output formats supported by the Cisco ONS 15454 and the Cisco ONS 15327, Release 4.0. Refer to the Cisco ONS 15454 and Cisco ONS 15327 TL1 Command Guide, Release 4.0 for a complete description of TL1 commands.

TL1 commands conform to the following syntax:
a:b:c:d:e: ...z;
where:
"a" is the Command Code
"b" is the Target Identifier (TID)
"c" is the Access Identifier (AID) or the User Identifier (UID)
"d" is the Correlation Tag (CTAG)
"e: ...z;" are other positions required for various commands
The TID, AID, and CTAG route and control the TL1 command.
Other parameters provide additional information required to complete the action requested by the command.

1  BLSR

Table 1 BLSR 

DLT-BLSR:[<TID>]:<AID>:<CTAG>[:::]; Deletes the BLSR of the NE

ED-BLSR:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>,][NODEID=<NODEID>,] [RVRTV=<RVRTV>,][RVTM=<RVTM>,][SRVRTV=<SRVRTV>,][SRVTM=<SRVTM>][:]; Edits the BLSR attributes

ENT-BLSR:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>,]NODEID=<NODEID>, MODE=<MODE>,[RVRTV=<RVRTV>,][RVTM=<RVTM>,][SRVRTV=<SRVRTV>,] [SRVTM=<SRVTM>,]EASTWORK=<EASTWORK>,WESTWORK=<WESTWORK>, [EASTPROT=<EASTPROT>,][WESTPROT=<WESTPROT>]; Creates either a two-fiber or four-fiber BLSR

EX-SW-<OCN_BLSR>:[TID]:<AID>:[CTAG]::[<ST>]; Exercises the algorithm for switching from a working facility to a protection facility without actually performing a switch.

REPT EVT RING Reports the occurrence of a non-alarmed event against a ring object for a BLSR

RTRV-BLSR:[<TID>]:[<AID>]:<CTAG>[::::]; Retrieves all of the BLSR information of the network element (NE) Output format: SID DATE TIME M CTAG COMPLD "[<AID>]::[RINGID=<RINGID>,][NODEID=<NODEID>,][MODE=<MODE>,] [RVRTV=<RVRTV>,][RVTM=<RVTM>,][SRVRTV=<SRVRTV>,][SRVTM=<SRVTM>,] [EASTWORK=<EASTWORK>,][WESTWORK=<WESTWORK>,] [EASTPROT=<EASTPROT>,][WESTPROT=<WESTPROT>]" ;

RTRV-COND-RING:[<TID>]:[<AID>]:<CTAG>::[<TYPEREQ>][,,,]; Retrieves the current standing condition against a ring object for BLSR Output format: SID DATE TIME M CTAG COMPLD "<AID>:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>], [<OCRTM>],,,[<DESC>]" ;

RTRV-TRC-<OCN_BLSR>::[<TID>]:<AID>:<CTAG>; Retrieves the valid J1 expected trace string, retrieved trace string, trace mode, C2 byte, and STS bandwidth of the OCN port only if the port has a BLSR Output format: SID DATE TIME M CTAG COMPLD "<AID>::[LEVEL=<LEVEL>,][EXPTRC=<EXPTRC>,][INCTRC=<INCTRC>,] [TRCMODE=<TRCMODE>,][C2=<C2>]" ;

2  Cross Connections

Table 2 Cross Connections 

DLT-CRS-<STS_PATH>:[<TID>]:<SRC>,<DST>:<CTAG>[:::]; Deletes a cross-connection between STS paths

DLT-CRS-VT1:[<TID>]:<FROM>,<TO>:<CTAG>[:::]; Deletes the VT1 cross-connections

ED-CRS-<STS_PATH>:[<TID>]:<SRC>,<DST>:<CTAG>:::[ADD=<ADD>,] [REMOVE=<REMOVE>]:[<PST>],[<SST>]; Edits the state of an STS cross-connection

ED-CRS-VT1:[<TID>]:<SRC>,<DST>:<CTAG>:::[ADD=<ADD>,][REMOVE=<REMOVE>] :[<PST>],[<SST>]; Edits VT cross-connections

ENT-CRS-<STS_PATH>:[<TID>]:<SRC>,<DST>:<CTAG>::[<CCT>]::[<PST>],[<SST>]; Creates an STS cross-connection with cross-connection types (CCT)

ENT-CRS-VT1:[<TID>]:<FROM>,<TO>:<CTAG>::[<CCT>]::[<PST>],[<SST>]; Creates a VT1 cross-connect

RTRV-CRS:[<TID>]:<AID>:<CTAG>:::[CRSTYPE=<CRSTYPE>][:]; Retrieves all the cross-connections based on the required CRSTYPE (for all STS connections) Output format: SID DATE TIME M CTAG COMPLD "<FROM>,<TO>:<CCT>,<MOD>::<PST>,[<SST>]" ;

RTRV-CRS-<STS_PATH>:[<TID>]:<SRC>:<CTAG>[::::]; Retrieves any connections associated with the entered AID(s) or AID range Output format: SID DATE TIME M CTAG COMPLD "<CROSSCONNECTID>,<CROSSCONNECTID1>:<CCT>,<MOD>::<PST>,[<SST>]" ;

RTRV-CRS-VT1:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the VT cross-connection information Output format: SID DATE TIME M CTAG COMPLD "<VT>,<VT1>:<CCT>::<PST>,[<SST>]" ;

3  DWDM (Cisco ONS 15454 only)

Table 3 DWDM 

DLT-FFP-CLNT:[<TID>]:<WORKAID>,<PROTAID>:<CTAG>[:::]; Deletes Y-cable protection on client facilities

ED-CLNT:[<TID>]:<AID>:<CTAG>:::[SFBER=<SFBER>,][SDBER=<SDBER>,] [ALSMODE=<ALSMODE>,][ALSRCINT=<ALSRCINT>,][ALSRCPW=<ALSRCPW>,] [COMM=<COMM>,][MACADDR=<MACADDR>,][SYNCMSG=<SYNCMSG>,] [SENDDUS=<SENDDUS>,][RLASER=<RLASER>][SOAK=<SOAK>]:[<PST>],[<SST>]; Edits client facility attributes

ED-DWDM:[<TID>]:<AID>:<CTAG>:::[PEERID=<PEERID>,][TERMMODE=<TERMMODE>,] [PAYLOAD=<PAYLOAD>,][PWL=<PWL>]; Edits an already pre-provisioned/provisioned MXP/TXP card

ED-FFP-CLNT:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>,][RVRTV=<RVRTV>,] [RVTM=<RVTM>,][PSDIRN=<PSDIRN>][:]; Edits a Y-cable protection group on client facilities

ED-OCH:[<TID>]:<AID>:<CTAG>:::[RDIRN=<RDIRN>,] [EXPWLEN=<EXPWLEN>,][VOAATTN=<VOAATTN>,] [VOAPWR=<VOAPWR>,][CALOPWR=<CALOPWR>,][SFBER=<SFBER>,] [SDBER=<SDBER>,][ALSMODE=<ALSMODE>,][ALSRCINT=<ALSRCINT>,] [ALSRCPW=<ALSRCPW>,][COMM=<COMM>,][GCCRATE=<GCCRATE>,] [OSFBER=<OSFBER>,][OSDBER=<OSDBER>,][DWRAP=<DWRAP>,] [FEC=<FEC>,][MACADDR=<MACADDR>,][SYNCMSG=<SYNCMSG>,] [SENDDUS=<SENDDUS>,][RLASER=<RLASER>,][SOAK=<SOAK>]:[<PST>],[<SST>]; Edits the attributes (service parameters) and state of an OCH facility

ED-TRC-CLNT:[<TID>]:<SRC>:<CTAG>:::[EXPTRC=<EXPTRC>,][TRC=<TRC>,] [TRCMODE=<TRCMODE>,]TRCLEVEL=<TRCLEVEL>,[TRCFORMAT=<TRCFORMAT>]; Edits trace-related attributes on client facilities

ED-TRC-OCH:[<TID>]:<SRC>:<CTAG>:::[EXPTRC=<EXPTRC>,][TRC=<TRC>,] [TRCMODE=<TRCMODE>,]TRCLEVEL=<TRCLEVEL>,[TRCFORMAT=<TRCFORMAT>]; Edits trace-related optical channel facilities

ENT-FFP-CLNT:[<TID>]:<WORKAID>,<PROTAID>:<CTAG>:::[PROTTYPE=<PROTTYPE>,] [PROTID=<PROTID>,][RVRTV=<RVRTV>,][RVTM=<RVTM>,][PSDIRN=<PSDIRN>][:]; Creates Y-cable protection on client facilities

OPR-PROTNSW-CLNT:[<TID>]:<AID>:<CTAG>::<SC>[:]; Operates a Y-cable protection switch request

RLS-PROTNSW-CLNT:[<TID>]:<AID>:<CTAG>[::]; Releases a Y-cable protection switch on client facilities

RTRV-CLNT:[<TID>]:<AID>:<CTAG>; Retrieves client facility attributes Output format: SID DATE TIME M CTAG COMPLD "<AID>:,,[<ROLE>],<STATUS>:[COMM=<COMM>,][SFBER=<SFBER>,] [SDBER=<SDBER>,][ALSMODE=<ALSMODE>,][ALSRCINT=<ALSRCINT>,] [ALSRCPW=<ALSRCPW>,][SYNCMSG=<SYNCMSG>,][SENDDUS=<SENDDUS>,] [LSRSTAT=<LSRSTAT>,][CLEI=<CLEI>,][PN=<PARTNUM>,][SN=<SERIALNUM>,] [VENDOR=<VENDOR>,][VENDORREV=<VENDORREV>,][OPTICS=<OPTICS>,] [MACADDR=<MACADDR>,][SOAK=<SOAK>]:<PST>,[<SST>]" ;

RTRV-DWDM:[<TID>]:<AID>:<CTAG>; Retrieves DWDM card-level attributes Output format: SID DATE TIME M CTAG COMPLD "<AID>:<AIDTYPE>,<EQUIP>,,[<STATUS>]:[PEERID=<PEERID>,] [TERMMODE=<TERMMODE>,][PAYLOAD=<PAYLOAD>,] [CARDNAME=<CARDNAME>,][PWL=<PWL>,] [TWL1=<TWL1>,][TWL2=<TWL2>,]:[<PST>],[<SST>]" ;

RTRV-FFP-CLNT:[<TID>]:<AID>:<CTAG>[::::]; Retrieves Y-cable protection on client facilities Output format: SID DATE TIME M CTAG COMPLD "<WORKAID>,<PROTAID>::[PROTTYPE=<PROTTYPE>,][PROTID=<PROTID>,] [RVRTV=<RVRTV>,][RVTM=<RVTM>,][PSDIRN=<PSDIRN>]" ;

RTRV-OCH:[<TID>]:<AID>:<CTAG>; Retrieves the attributes (service parameters) and state of an OCH facility Output format: SID DATE TIME M CTAG COMPLD "<AID>:,,,[<STATUS>],[<RDIRN>],[<OPTICALPORTTYPE>],[<POWER>],[<EXPWLEN>], [<ACTWLEN>]:[ILOSS=<ILOSS>,] [VOAMODE=<VOAMODE>,][VOAATTN=<VOAATTN>,] [VOAPWR=<VOAPWR>,][VOAREFATTN=<VOAREFATTN>,] [VOAREFPWR=<VOAREFPWR>,][REFOPWR=<REFOPWR>,][CALOPWR=<CALOPWR>,] [SFBER=<SFBER>,][SDBER=<SDBER>,][ALSMODE=<ALSMODE>,] [ALSRCINT=<ALSRCINT>,][ALSRCPW=<ALSRCPW>,][COMM=<COMM>,] [GCCRATE=<GCCRATE>,][DWRAP=<DWRAP>,][FEC=<FEC>,][OSFBER=<OSFBER>,] [OSDBER=<OSDBER>,][MACADDR=<MACADDR>,][SYNCMSG=<SYNCMSG>,] [SENDDUS=<SENDDUS>,][LSRSTAT=<LSRSTAT>,][SOAK=<SOAK>]:<PST>,[<SST>]" ;

RTRV-PROTNSW-CLNT:[<TID>]:<AID>:<CTAG>[::::]; Retrieves protection switch status of client facilities Output format: SID DATE TIME M CTAG COMPLD "<AID>:<SC>,[<SWITCHTYPE>]" ;

RTRV-TRC-CLNT:[<TID>]:<SRC>:<CTAG>::[<MSGTYPE>], [<TRCLEVEL>][::]; Retrieves the SONET J0 Section sent trace string, expected trace string, received trace string, trace mode, and the trace level for the client facility Output format: SID DATE TIME M CTAG COMPLD "[TRCLEVEL=<TRCLEVEL>,][EXPTRC=<EXPTRC>,][TRC=<TRC>,][INCTRC=<INCTRC>,] [TRCMODE=<TRCMODE>,][TRCFORMAT=<TRCFORMAT>]" ;

RTRV-TRC-OCH:[<TID>]:<SRC>:<CTAG>::[<MSGTYPE>],[<TRCLEVEL>][::]; Retrieves the sent trace string, expected trace string, received trace string, trace mode, and the trace level for the SONET J0 Section, the TTI PATH and SECTION monitoring levels of the DWDM facility Output format: SID DATE TIME M CTAG COMPLD "[TRCLEVEL=<TRCLEVEL>,][EXPTRC=<EXPTRC>,][TRC=<TRC>,][INCTRC=<INCTRC>,] [TRCMODE=<TRCMODE>,][TRCFORMAT=<TRCFORMAT>]" ;

4  Environment Alarms and Controls

Table 4 Environment Alarms and Controls 

OPR-ACO-ALL:[<TID>]::<CTAG>; Operates the cut-off of the office audible alarm indications without changing the local alarm indications

OPR-EXT-CONT:[<TID>]:<AID>:<CTAG>::[<CONTTYPE>],[<DURATION>]; Operates an external control and closes the external control contact

REPT ALM ENV Reports a user-defined condition on an environmental alarm input

REPT EVT ENV Reports a non-alarmed event against an environment alarm input

RLS-EXT-CONT:[<TID>]:<AID>:<CTAG>[::,]; Releases a forced contact state and returns the control of the contact to an automatic control state

RTRV-ALM-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>]; Retrieves the environmental alarms Output format: SID DATE TIME M CTAG COMPLD "<AID>:<NTFCNCDE>,<ALMTYPE>,,,[<DESC>]" ;

RTRV-ATTR-CONT:[<TID>]:<AID>:<CTAG>[::<CONTTYPE>]; Retrieves the attributes associated with an external control Output format: SID DATE TIME M CTAG COMPLD "<AID>:[<CONTTYPE>]" ;

RTRV-ATTR-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>]; Retrieves the attributes associated with an environmental alarm Output format: SID DATE TIME M CTAG COMPLD "<AID>:[<NTFCNCDE>],[<ALMTYPE>],[<DESC>]" ;

RTRV-COND-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>][,,,]; Retrieves the environmental conditions Output format: SID DATE TIME M CTAG COMPLD "<AID>:<NTFCNCDE>,<ALMTYPE>,[<OCRDAT>],[<OCRTM>],,,,[<DESC>]" ;

RTRV-EXT-CONT:[<TID>]:<AID>:<CTAG>[::<CONTTYPE>]; Retrieves the control state of an external control Output format: SID DATE TIME M CTAG COMPLD "<AID>:[<CONTTYPE>],<DUR>,[<CONTSTATE>]" ;

SET-ATTR-CONT:[<TID>]:<AID>:<CTAG>[::<CONTTYPE>]; Sets the attributes associated with an external control

SET-ATTR-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>],[<ALMMSG>]; Sets the attributes associated with an external alarm

5  Equipment

Table 5 Equipment 

ALW-SWDX-EQPT:[<TID>]:<AID>:<CTAG>[::]; Allows automatic or manual switching on a duplex system containing duplexed or redundant equipment

ALW-SWTOPROTN-EQPT:[<TID>]:<AID>:<CTAG>[::<DIRN>]; Allows automatic or manual switching of an equipment unit back to a protection status

ALW-SWTOWKG-EQPT:[<TID>]:<AID>:<CTAG>[::<DIRN>]; Allows automatic or manual switching of an equipment unit back to a working status

DLT-EQPT:[<TID>]:<AID>:<CTAG>[:::]; Deletes a card from the NE

ED-EQPT:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>,][PRTYPE=<PRTYPE>,] [RVRTV=<RVRTV>,][RVTM=<RVTM>][:]; Edits the attributes for a given equipment slot in the NE

ENT-EQPT:[<TID>]:<AID>:<CTAG>::<AIDTYPE>:[PROTID=<PROTID>,] [PRTYPE=<PRTYPE>,][RVRTV=<RVRTV>,][RVTM=<RVTM>][:]; Enters the card type and attributes for a given equipment slot in the NE

INH-SWDX-EQPT:[<TID>]:<AID>:<CTAG>[::]; Inhibits the automatic or manual switching on an NE containing duplex equipment

INH-SWTOPROTN-EQPT:[<TID>]:<AID>:<CTAG>[::<DIRN>]; Inhibits automatic or manual switching of an equipment unit to protection

INH-SWTOWKG-EQPT:[<TID>]:<AID>:<CTAG>[::<DIRN>]; Inhibits automatic or manual switching of an equipment unit back to the working unit

REPT ALM EQPT Reports an alarm condition against an equipment unit or slot

REPT EVT EQPT Reports the occurrence of a non-alarmed event against an equipment unit or slot

RTRV-ALM-EQPT:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>], [<SRVEFF>][,,,]; Retrieves and sends the current status of alarm conditions associated with the equipment units Output format: SID DATE TIME M CTAG COMPLD "[<AID>],[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,,,,:[<DESC>]" ;

RTRV-COND-EQPT:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,]; Retrieves the equipment conditions Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>], [<OCRTM>],,,[<DESC>]" ;

RTRV-EQPT:[<TID>]:<AID>:<CTAG>[::::]; Retrieves protection group information and status information for all cards Output format: SID DATE TIME M CTAG COMPLD "<AID>:<AIDTYPE>,<EQUIP>,[<ROLE>],[<STATUS>]:[PROTID=<PROTID>,] [PRTYPE=<PRTYPE>,][RVRTV=<RVRTV>,][RVTM=<RVTM>,] [CARDNAME=<CARDNAME>,][IOSCFG=<IOSCFG>]:[<PST>],[<SST>]" ;

SW-DX-EQPT:[<TID>]:<AID>:<CTAG>::[<MODE>][,]; Switches an XC/XCVT/XC10G card with the mate card within the NE

SW-TOPROTN-EQPT:[<TID>]:<AID>:<CTAG>::[<MODE>],[<PROTID>],[<DIRN>]; Performs an equipment unit protection switch

SW-TOWKG-EQPT:[<TID>]:<AID>:<CTAG>::[<MODE>],[<DIRN>]; Switches the protected working unit back to the working unit

6  Fault

Table 6 Fault 

REPT ALM <MOD2ALM> Reports an alarm condition against a facility or a path

REPT ALM COM Reports an alarm condition when an AID cannot be given

REPT ALM ENV Reports a customer-defined condition on an environmental alarm input

REPT ALM RING Reports an alarm condition against a ring object for BLSR

REPT EVT <MOD2ALM> Reports the occurrence of a non-alarmed event

REPT EVT COM Reports a non-alarmed event against an NE when there is no AID associated with it

RTRV-ALM-<MOD2ALM>:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>], [<CONDTYPE>],[<SRVEFF>][,,,]; Retrieves and sends the current status of the alarm conditions Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,,,,:[<DESC>]" ;

RTRV-ALM-ALL:[<TID>]::<CTAG>::[<NTFCNCDE>],[<CONDITION>],[<SRVEFF>][,,,]; Retrieves and sends the current status of all active alarm conditions Output format: SID DATE TIME M CTAG COMPLD "[<AID>],[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,,,,:[<DESC>],[<AIDDET>]" ;

RTRV-ALM-RING:[<TID>]:[<AID>]:<CTAG>::[<NTFCNCDE>],[<CONDITION>], [<SRVEFF>][,,,]; Retrieves and sends the current status of all active alarm conditions against a ring object for BLSR Output format: SID DATE TIME M CTAG COMPLD "<AID>:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,,,,:[<DESC>]" ;

RTRV-COND-<MOD2ALM>:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,]; Retrieves the current standing condition and/or state associated with an entity Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>], [<OCRTM>],,,[<DESC>]" ;

RTRV-COND-ALL:[<TID>]::<CTAG>::[<TYPEREQ>][,,,]; Retrieves the current standing condition for all entities Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>], [<OCRTM>],,,[<DESC>]" ;

7  IOS

Table 7 IOS 

COPY-IOSCFG:[<TID>]:<AID>:<CTAG>::SRC=<SRC>,DEST=<DEST>; Uploads startup IOS configuration files from the network to the node and downloads startup IOS configuration files from the node to the network (ML-series Ethernet cards)

REPT EVT IOSCFG Reports the status of copying the IOS configuration file when the COPY-IOSCFG command is issued

8  Log

Table 8 Log 

ALW-MSG-DBCHG:[<TID>]::<CTAG>[::,,]; Enables REPT DBCHG

INH-MSG-DBCHG:[<TID>]::<CTAG>[::,,]; Disables REPT DBCHG

REPT DBCHG Reports any changes on the NE that result from certain TL1 commands or an external event

RTRV-LOG:[<TID>]::<CTAG>::<LOGNM>; Retrieves the alarm log of the NE Output format: SID DATE TIME M CTAG COMPLD "<AID>,<ALMNUMBER>:CURRENT=<CURRENT>,[PREVIOUS=<PREVIOUS>,] <CONDITION>,<SRVEFF>,[TIME=<OCRTIME>,][DATE=<OCRDAT>]:<ALMDESCR>" ;

9  Network

Table 9 Network 

RTRV-MAP-NETWORK:[<TID>]::<CTAG>; Retrieves all the NE attributes which are reachable from the GNE Output format: SID DATE TIME M CTAG COMPLD "<IPADDR>,<NODENAME>,<PRODUCT>" ;

RTRV-NE-IPMAP:[<TID>]:[<AID>]:<CTAG>; Retrieves the IP address and node name of the NEs that have the DCC connection with this NE Output format: SID DATE TIME M CTAG COMPLD "<AID>:<IPADDR>,<NODENAME>" ;

10  Performance

Table 10 Performance 

ALW-PMREPT-ALL:[<TID>]::<CTAG>; Resumes processing all the PM reports that are inhibited

INH-PMREPT-ALL:[<TID>]::<CTAG>; Inhibits all scheduled PM reporting

INIT-REG-<MOD2>:[<TID>]:<AID>:<CTAG>::,,[<LOCN>],[<DIRN>],[<TMPER>][,,]; Initializes the performance monitoring (PM) registers

REPT PM <MOD2> Reports of performance monitoring statistics as a result of schedule created by SCHED-PMREPT

RTRV-PM-<MOD2>:[<TID>]:<AID>:<CTAG>::[<MONTYPE>],[<MONLEV>],[<LOCN>], [<DIRN>],[<TMPER>],[<DATE>],[<TIME>]; Retrieves the values of PM parameters for a specified card type Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:<MONTYPE>,<MONVAL>,[<VLDTY>],[<LOCN>],[<DIRN>], [<TMPER>],[<MONDAT>],[<MONTM>]" ;

RTRV-PMMODE-<STS_PATH>:[<TID>]:<AID>:<CTAG>::<LOCN>; Retrieves the PM mode that has been previously set in the NE data collection Output format: SID DATE TIME M CTAG COMPLD "<AID>:[<LOCN>],<MODETYPE>" ;

RTRV-PMSCHED-<MOD2>:[<TID>]:<AID>:<CTAG>; Retrieves the PM reporting schedule that was set for the NE by SCHED-PMREPT Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:<REPTINVL>,<REPTDAT>,<REPTTM>,[<NUMINVL>],, [<MONLEV>],<LOCN>,,[<TMPER>],[<TMOFST>],[<INHMODE>]" ;

RTRV-PMSCHED-ALL:[<TID>]::<CTAG>; Retrieves all the PM reporting schedules that were set for the NE by SCHED-PMREPT Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:<REPTINVL>,<REPTDAT>,<REPTTM>,[<NUMINVL>],, [<MONLEV>],<LOCN>,,[<TMPER>],<TMOFST>,[<INHMODE>]" ;

RTRV-TH-<MOD2>:[<TID>]:<AID>:<CTAG>::[<MONTYPE>],[<LOCN>],<TMPER>[::]; Retrieves the current threshold level of one or more monitored parameters Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:<MONTYPE>,[<LOCN>],,<THLEV>,[<TMPER>]" ;

SCHED-PMREPT-<MOD2>:[<TID>]:<SRC>:<CTAG>::[<REPTINVL>], [<REPTSTATM>],[<NUMREPT>],,[<MONLEV>],[<LOCN>],,[<TMPER>],[<TMOFST>]; Schedules/reschedules the NE to report the performance monitoring data for a line facility or for an STS/VT path periodically, using an automatic REPT PM message

SET-PMMODE-<STS_PATH>:[<TID>]:<AID>:<CTAG>::<LOCN>,<MODETYPE>,[<PMSTATE>]; Sets the mode and turns the PM data collection mode on or off

SET-TH-<MOD2>:[<TID>]:<AID>:<CTAG>::<MONTYPE>,<THLEV>,[<LOCN>],,[<TMPER>]; Sets the threshold for PM and sets the alarm thresholds for the MXP/TXP cards

11  Ports

Table 11 Ports 

ED-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>:::[DCC=<DCC>,][SYNCMSG=<SYNCMSG>,] [SENDDUS=<SENDDUS>,][PJMON=<PJMON>,][SFBER=<SFBER>,][SDBER=<SDBER>,] [MODE=<MODE>,][MUX=<MUX>,][SOAK=<SOAK>]:[<PST>],[<SST>]; Edits the attributes and state of an OC-N facility

ED-DS1:[<TID>]:<AID>:<CTAG>[:::TACC=<TACC>]; Edits the test access attributes for DS1 access on a DS3XM card

ED-EC1:[<TID>]:<AID>:<CTAG>:::[PJMON=<PJMON>,][LBO=<LBO>,] [SOAK=<SOAK>]:[<PST>],[<SST>]; Edits the attributes of an EC1

ED-G1000:[<TID>]:<AID>:<CTAG>:::[MFS=<MFS>,][FLOW=<FLOW>,] [OPTICS=<OPTICS>,][ALS=<ALS>,][TRANS=<TRANS>]:[<PST>],[<SST>]; Edits the attributes related to a G1000 port

ED-T1:[<TID>]:<AID>:<CTAG>:::[LINECDE=<LINECDE>,][FMT=<FMT>,] [LBO=<LBO>,][TACC=<TACC>,][SOAK=<SOAK>]:[<PST>],[<SST>]; Edits the attributes related a DS1/T1 port

ED-T3:[<TID>]:<AID>:<CTAG>:::[FMT=<FMT>,][LINECDE=<LINECDE>,] [LBO=<LBO>,][TACC=<TACC>,][SOAK=<SOAK>]:[<PST>],[<SST>]; Edits the attributes related to a DS3/T3 port

INIT-REG-G1000:[<TID>]:<src>:<CTAG>::,,<LOCATION>,<DIRECTION>,<TMPER>[,,]; Initializes the performance monitoring registers for the G1000-4 and G1000-2 ports

RMV-<MOD2_IO>:[<TID>]:<AID>:<CTAG>::[<CMDMODE>],[<PST>],[<SST>]; Removes a facility from service

RST-<MOD2_IO>:[<TID>]:<AID>:<CTAG>[::]; Provisions a facility in service

RTRV-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the attributes and state of an OC-N facility Output format: SID DATE TIME M CTAG COMPLD "<AID>:,,[<ROLE>],[<STATUS>]:[DCC=<DCC>,][TMGREF=<TMGREF>,] [SYNCMSG=<SYNCMSG>,][SENDDUS=<SENDDUS>,] [PJMON=<PJMON>,][SFBER=<SFBER>,][SDBER=<SDBER>,] [MODE=<MODE>,][WVLEN=<WVLEN>,][RINGID=<RINGID>,] [BLSRTYPE=<BLSRTYPE>,][MUX=<MUX>,][UNIC=<UNIC>,] [CCID=<CCID>,][NBRIX=<NBRIX>,][SOAK=<SOAK>]:<PST>,[<SST>]" ;

RTRV-DS1:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the test access attributes on a DS1 layer of DS3XM card Output format: SID DATE TIME M CTAG COMPLD "<AID>::[TACC=<TACC>]" ;

RTRV-EC1:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the facility status of an EC1 card Output format: SID DATE TIME M CTAG COMPLD "<AID>::[PJMON=<PJMON>,][LBO=<LBO>,][RXEQUAL=<RXEQUAL>,] [SOAK=<SOAK>]:<PST>,[<SST>]" ;

RTRV-FSTE:[<TID>]:<AID>:<CTAG>; Retrieves the front end port information of the ML100T-12 Ethernet card Output format: SID DATE TIME M CTAG COMPLD "<AID>::[ADMINSTATE=<ADMINSTATE>,][LINKSTATE=<LINKSTATE>,] [MTU=<MTU>,][FLOWCTRL=<FLOWCTRL>,][DUPLEX=<DUPLEX>,][SPEED=<SPEED>]" ;

RTRV-G1000:[<TID>]:<AID>:<CTAG>; Retrieves the G1000 facilities configuration Output format: SID DATE TIME M CTAG COMPLD "<AID>::[MFS=<MFS>,][FLOW=<FLOW>,][LAN=<LAN>,][OPTICS=<OPTICS>]: <PST>,[<SST>]" ;

RTRV-GIGE:[<TID>]:<AID>:<CTAG>; Retrieves the front end port information for the ML1000-2 Ethernet card Output format: SID DATE TIME M CTAG COMPLD "<AID>::[ADMINSTATE=<ADMINSTATE>,][LINKSTATE=<LINKSTATE>,][MTU=<MTU>,] [FLOWCTRL=<FLOWCTRL>,][OPTICS=<OPTICS>,][DUPLEX=<DUPLEX>,] [SPEED=<SPEED>]" ;

RTRV-POS:[<TID>]:<AID>:<CTAG>; Retrieves the back end port information for the ML-series Ethernet cards when the back end port is working in POS mode Output format: SID DATE TIME M CTAG COMPLD "<AID>::[ADMINSTATE=<ADMINSTATE>,][LINKSTATE=<LINKSTATE>,][MTU=<MTU>]" ;

RTRV-T1:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the DS1 facilities configuration Output format: SID DATE TIME M CTAG COMPLD "<AID>::[LINECDE=<LINECDE>,][FMT=<FMT>,][LBO=<LBO>,][TACC=<TAP>,] [SOAK=<SOAK>]:<PST>,[<SST>]" ;

RTRV-T3:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the facilities properties of a DS3 and DS3XM card Output format: SID DATE TIME M CTAG COMPLD "<AID>::[FMT=<FMT>,][LINECDE=<LINECDE>,][LBO=<LBO>,][TACC=<TAP>,] [SOAK=<SOAK>]:<PST>,[<SST>]" ;

12  Security

Table 12 Security 

ACT-USER:[<TID>]:<UID>:<CTAG>::<PID>; Sets up a session with the NE

ALW-MSG-SECU:[<TID>]::<CTAG>; Allows REPT EVT SECU and REPT ALM SECU

CANC Reports the occurrence of a session timeout event Output format: SID DATE TIME A ATAG CANC "<UID>" ;

CANC-USER:[<TID>]:<USERID>:<CTAG>; Logs a user out of an active session with the NE

DLT-USER-SECU:[<TID>]:<UID>:<CTAG>; Deletes a user; can only be performed by a Superuser

ED-PID:[<TID>]:<UID>:<CTAG>::<OLDPID>,<NEWPID>; Allows a user to change his or her own password

ED-USER-SECU:[<TID>]:<UID>:<CTAG>::[<NEWUID>],[<NEWPID>],,[<UAP>][:]; Edits a user's privileges, password, or ID and can only be performed by a Superuser

ENT-USER-SECU:[<TID>]:<UID>:<CTAG>::<PID>,,<UAP>[:]; Adds a user account; can only be performed by a Superuser

INH-MSG-SECU:[<TID>]::<CTAG>; Inhibits the REPT EVT SECU and REPT ALM SECU messages

REPT EVT SECU Reports the occurrence of a non-alarmed security event against the NE

REPT EVT SESSION Reports a non-alarmed event related to establishing a session with the NE

RTRV-USER-SECU:[<TID>]:<UID>:<CTAG>; Retrieves the security information of a specified user or list of users Output format: SID DATE TIME M CTAG COMPLD "<UID>:,<UAP>" ;

13  SONET Line Protection

Table 13 SONET Line Protection 

DLT-FFP-<OCN_TYPE>:[<TID>]:<WORK>,<PROTECT>:<CTAG>[:::]; Deletes an OCN facility protection group in a 1+1 architecture

ED-FFP-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>,][RVRTV=<RVRTV>,] [RVTM=<RVTM>,][PSDIRN=<PSDIRN>][:]; Edits the optical facility protection

ENT-FFP-<OCN_TYPE>:[<TID>]:<WORK>,<PROTECT>:<CTAG>:::[PROTID=<PROTID>,] [RVRTV=<RVRTV>,][RVTM=<RVTM>,][PSDIRN=<PSDIRN>][:]; Creates an optical 1+1 protection

OPR-PROTNSW-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>::<SC>,[<SWITCHTYPE>]; Initiates a SONET line protection switch request

RLS-PROTNSW-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>[::]; Releases a SONET line protection switch request

RTRV-FFP-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the optical facility protection information Output format: SID DATE TIME M CTAG COMPLD "<WORK>,<PROTECT>::[PROTID=<PROTID>,][RVRTV=<RVRTV>,][RVTM=<RVTM>,] [PSDIRN=<PSDIRN>]" ;

RTRV-PROTNSW-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the switching state of a SONET line specified in the AID Output format: SID DATE TIME M CTAG COMPLD "<AID>:<SC>,[<SWITCHTYPE>]" ;

14  Software Download

Table 14 Software Download 

APPLY:[<TID>]::<CTAG>[::<MEM_SW_TYPE>]; Activates or reverts a software load during a software upgrade or downgrade process

COPY-RFILE:[<TID>]:[<SRC>]:<CTAG>::TYPE=<XFERTYPE>,[SRC=<SRC1>,] [DEST=<DEST>]; Downloads a new software package from the location specified by the FTP URL. Also used to backup and restore the system database.

REPT EVT FXFR Reports the FTP software download status of the start, completion, and completed percentage

15  STS and VT Paths

Table 15 STS and VT Paths 

ED-<STS_PATH>:[<TID>]:<SRC>:<CTAG>:::[SFBER=<SFBER>,][SDBER=<SDBER>,] [RVRTV=<RVRTV>,][RVTM=<RVTM>,][SWPDIP=<SWPDIP>,] [HOLDOFFTIMER=<HOLDOFFTIMER>,][EXPTRC=<EXPTRC>,][TRC=<TRC>,] [TRCMODE=<TRCMODE>,][TACC=<TACC>]:[<PST>],[<SST>]; Edits the attributes associated with an STS path

ED-VT1:[<TID>]:<SRC>:<CTAG>:::[RVRTV=<RVRTV>,][RVTM=<RVTM>,] [HOLDOFFTIMER=<HOLDOFFTIMER>,][TACC=<TACC>]:[<PST>],[<SST>]; Edits the attributes associated with a VT1 path

RTRV-<STS_PATH>:[<TID>]:<AID>:<CTAG>:::[BLSRPTHTYPE=<BLSRPTHTYPE>][:]; Retrieves the attributes associated with an STS path Output format: SID DATE TIME M CTAG COMPLD "<AID>::[LEVEL=<LEVEL>,][SFBER=<SFBER>,][SDBER=<SDBER>,][RVRTV=<RVRTV>,] [RVTM=<RVTM>,][SWPDIP=<SWPDIP>,][HOLDOFFTIMER=<HOLDOFFTIMER>,] [EXPTRC=<EXPTRC>,][TRC=<TRC>,][INCTRC=<INCTRC>,][TRCMODE=<TRCMODE>,] [TACC=<TACC>,][UPSRPTHSTATE=<UPSRPTHSTATE>,][C2=<C2>,] [BLSRPTHSTATE=<BLSRPTHSTATE>]:[<PST>],[<SST>]" ;

RTRV-PTHTRC-<STS_PATH>:[<TID>]:<AID>:<CTAG>::[<MSGTYPE>][:<LOCN>]; Retrieves the contents of the SONET path trace message that is transported in the J1 byte of the SONET STS path Output format: SID DATE TIME M CTAG COMPLD "<TRACMSG>" ;

RTRV-VT1:[<TID>]:<SRC>:<CTAG>[::::]; Retrieves the attributes associated with a VT1 path Output format: SID DATE TIME M CTAG COMPLD "<VT>::[RVRTV=<RVRTV>,][RVTM=<RVTM>,][HOLDOFFTIMER=<HOLDOFFTIMER>,] [TACC=<TACC>][UPSRPTHSTATE=<UPSRPTHSTATE>]:[<PST>],[<SST>]" ;

16  Synchronization

Table 16 Synchronization 

ED-BITS:[<TID>]:<AID>:<CTAG>:::[LINECDE=<LINECDE>,][FMT=<FMT>,][LBO=<LBO>,] [SYNCMSG=<SYNCMSG>,][AISTHRSHLD=<AISTHRSHLD>][:<PST>]; Edits the BITS reference attributes

ED-NE-SYNCN:[<TID>]::<CTAG>:::[TMMD=<TMMD>,][SSMGEN=<SSMGEN>,] [QRES=<QRES>,][RVRTV=<RVRTV>,][RVTM=<RVTM>]; Edits the synchronization attributes of the NE

ED-SYNCN:[<TID>]:<AID>:<CTAG>:::[PRI=<PRI>,][SEC=<SEC>,][THIRD=<THIRD>][:]; Edits the synchronization reference list used to determine the sources for the NE's reference clock and the BITS output clock

OPR-SYNCNSW:[<TID>]:[<AID>]:<CTAG>::<SWITCHTO>,[<SC>]; Initiates a switch to the reference specified by the synchronization reference number if the reference supplied is valid

REPT ALM BITS Reports an alarm condition on a BITS facility

REPT ALM SYNCN Reports an alarm condition against a synchronization reference

REPT EVT BITS Reports the occurrence of a non-alarmed event against a BITS facility

REPT EVT SYNCN Reports the occurrence of a non-alarmed event against a synchronization entity

RLS-SYNCNSW:[<TID>]:[<AID>]:<CTAG>; Releases the previous synchronization reference provided by the OPR-SYNCNSW command

RTRV-ALM-BITS:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],[<SRVEFF>][,,,]; Retrieves and sends the current status of alarm conditions associated with the BITS facility Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,,,,:[<DESC>]" ;

RTRV-ALM-SYNCN:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>], [<SRVEFF>][,,,]; Retrieves and sends the current status of alarm conditions associated with a synchronization facility Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,,,,:[<DESC>]" ;

RTRV-BITS:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the BITS configuration command Output format: SID DATE TIME M CTAG COMPLD "<AID>::[LINECDE=<LINECDE>,][FMT=<FMT>,][LBO=<LBO>,][SYNCMSG=<SYNCMSG>,] [AISTHRSHLD=<AISTHRSHLD>]:[<PST>]" ;

RTRV-COND-BITS:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,]; Retrieves the standing condition on BITS Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>], [<OCRTM>],,,[<DESC>]" ;

RTRV-COND-SYNCN:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,]; Retrieves the synchronization condition Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>], [<OCRDAT>],[<OCRTM>],,,[<DESC>]" ;

RTRV-NE-SYNCN:[<TID>]::<CTAG>[::::]; Retrieves the synchronization attributes of the NE Output format: SID DATE TIME M CTAG COMPLD "::[TMMD=<TMMD>,][SSMGEN=<SSMGEN>,][QRES=<QRES>,][RVRTV=<RVRTV>,] [RVTM=<RVTM>]" ;

RTRV-SYNCN:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the synchronization reference list used to determine the sources for the NE's reference clock and the BITS output clock Output format: SID DATE TIME M CTAG COMPLD "<AID>:<REF>,<REFVAL>,[<QREF>],[<STATUS>],[<PROTECTSTATUS>]" ;

17  System

Table 17 System 

ALW-MSG-ALL:[<TID>]::<CTAG>[::,,]; Allows REPT ALM and REPT EVT autonomous messages to be transmitted

ED-DAT:[<TID>]::<CTAG>::[<DATE>],[<TIME>]; Edits the date and the time

ED-NE-GEN:[<TID>]::<CTAG>:::[NAME=<NAME>,][IPADDR=<IPADDR>,] [IPMASK=<IPMASK>,][DEFRTR=<DEFRTR>,][IIOPPORT=<IIOPPORT>,][NTP=<NTP>]; Edits the general node attributes of an NE

INH-MSG-ALL:[<TID>]::<CTAG>[::,,]; Inhibits REPT ALM and REPT EVT autonomous messages from being transmitted

INIT-SYS:[<TID>]:<AID>:<CTAG>[::]; Initializes the specified card and its associated subsystem(s)

RTRV-HDR:[<TID>]::<CTAG>; Retrieves the header of a TL1 response message

RTRV-INV:[<TID>]:<AID>:<CTAG>[::::]; Retrieves a listing of the equipment inventory Output format: SID DATE TIME M CTAG COMPLD "<AID>,<AIDTYPE>::[PN=<PN>,][HWREV=<HWREV>,] [FWREV=<FWREV>,][SN=<SN>,][CLEI=<CLEI>][TWL1=<TWL1>,][TWL2=<TWL2>,] [PLUGINVERNDORID=<PLUGINVERNDORID>,][PLUGINPN=<PLUGINPN>,] [PLUGINHWREV=<PLUGINHWREV>,][PLUGINFWREV=<PLUGINFWREV>,] [PLUGINSN=<PLUGINSN>,][ILOSSREF=<ILOSSREF>]" ;

RTRV-NE-GEN:[<TID>]::<CTAG>; Retrieves the general NE attributes Output format: SID DATE TIME M CTAG COMPLD "[IPADDR=<IPADDR>,][IPMASK=<IPMASK>,][DEFRTR=<DEFRTR>,] [IIOPPORT=<IIOPPORT>,][NTP=<NTP>,][ETHIPADDR=<ETHIPADDR>,] [ETHIPMASK=<ETHIPMASK>,][NAME=<NAME>,][SWVER=<SWVER>,][LOAD=<LOAD>,] [PROTSWVER=<PROTSWVER>,][PROTLOAD=<PROTLOAD>,][DEFDESC=<DEFDESC>] [PLATFORM=<PLATFORM>]" ;

RTRV-TOD:[<TID>]::<CTAG>; Retrieves the system date and time at the instant the command is executed Output format: SID DATE TIME M CTAG COMPLD "<YEAR>,<MONTH>,<DAY>,<HOUR>,<MINUTE>,<SECOND>,<TMTYPE>" ;

SET-TOD:[<TID>]::<CTAG>::<YEAR>,<MONTH>,<DAY>,<HOUR>,<MINUTE>, <SECOND>,[<DIFFERENCE>][:DST=<DST>]; Sets the system date and time for the NE

18  Test Access

Table 18 Test Access 

CHG-ACCMD-<MOD_TACC>:[<TID>]:<TAP>:<CTAG>::<MD>; Changes the test access mode for the circuit being tested

CONN-TACC-<MOD_TACC>:[<TID>]:<AID>:<CTAG>::<TAP>:MD=<MD>; Connects the STS or VT defined by AID to the STS specified by the TAP number Output format: SID DATE TIME M CTAG COMPLD "<TAP>" ;

DISC-TACC:[<TID>]:<TAP>:<CTAG>; Disconnects the TAP and puts the connection back to its original state

RTRV-TACC:[<TID>]:<TAP>:<CTAG>; Retrieves details associated with a TAP Output format: SID DATE TIME M CTAG COMPLD "<TAP>:<TACC_AID1>,<TACC_AID2>,[<MD>],[<E_CONN>],[<F_CONN>]" ;

19  Testing

Table 19 Testing 

OPR-LPBK-<MOD2>:[<TID>]:<SRC>:<CTAG>::,,,[<LPBKTYPE>]; Operates a signal loopback on an I/O card or on a cross-connect

RLS-LPBK-<MOD2>:[<TID>]:<SRC>:<CTAG>::,,,[<LPBKTYPE>]; Releases a signal loopback on an I/O card or on a cross-connect

20  UCP

Table 20 UCP 

DLT-UCP-CC:[<TID>]:<AID>:<CTAG>[::::]; Deletes a UCP IP control channel

DLT-UCP-IF:[<TID>]:<AID>:<CTAG>[::::]; Deletes a UCP interface

DLT-UCP-NBR:[<TID>]:<AID>:<CTAG>[::::]; Deletes a UCP neighbor

ED-UCP-CC:[<TID>]:<AID>:<CTAG>:::[LOCALIPCC=<LOCALIPCC>,] [REMOTEIPCC=<REMOTEIPCC>,][LMPHELLOINT=<LMPHELLOINT>,] [LMPHELLODEADINT=<LMPHELLODEADINT>,][MTU=<MTU>,] [CRCMD=<CRCMD>][:]; Edits UCP IP control channel attributes

ED-UCP-IF:[<TID>]:<AID>:<CTAG>:::[TNATYPE=<TNATYPE>,] [TNAADDR=<TNAADDR>,][CORENETWORKID=<CORENETWORKID>][:]; Edits UCP interface attributes

ED-UCP-NBR:[<TID>]:<AID>:<CTAG>:::[NAME=<NAME>,][HELLOEN=<HELLOEN>,] [HELLOINT=<HELLOINT>,][REFREDEN=<REFREDEN>][:]; Edits a UCP neighbor

ED-UCP-NODE:[<TID>]::<CTAG>:::[NODEID=<NODEID>,][INITRETRY=<INITRETRY>,] [MAXRETRY=<MAXRETRY>,][RESTARTTM=<RESTARTTM>,][RECOVTM=<RECOVTM>,] [RXMTINT=<RXMTINT>,][RFRSHINT=<RFRSHINT>,][RESVTIMEOUT=<RESVTIMEOUT>,] [RESVCONFTIMEOUT=<RESVCONFTIMEOUT>,][SOURCEDIP=<SOURCEDIP>,] [DESTINATIONDIP=<DESTINATIONDIP>][:]; Edits a UCP node level attributes

ENT-UCP-CC:[<TID>]:[<AID>]:<CTAG>:::[NBRIX=<NBRIX>,][CCTYPE=<CCTYPE>,] [PORT=<PORT>,][LOCALCCID=<LOCALCCID>,][LOCALIPCC=<LOCALIPCC>,] [REMOTCCID=<REMOTECCID>,][REMOTEIPCC=<REMOTEIPCC>,] [LMPHELLOINT=<LMPHELLOINT>,][LMPHELLODEADINT=<LMPHELLODEADINT>,] [MTU=<MTU>,][CRCMD=<CRCMD>,][TUNMD=<TUNMD>][:]; Creates a UCP IP control channel

ENT-UCP-IF:[<TID>]:<AID>:<CTAG>:::[NBRIX=<NBRIX>,][CCID=<CCID>,] [LOCALIFID=<LOCALIFID>,][REMOTEIFID=<REMOTEIFID>,][TNATYPE=<TNATYPE>,] [TNAADDR=<TNAADDR>,][CORENETWORKID=<CORENETWORKID>][:]; Creates a UCP interface

ENT-UCP-NBR:[<TID>]:<AID>:<CTAG>:::[NBRIX=<NBRIX>,][NODEID=<NODEID>,] NAME=<NAME>,[NDEN=<NDEN>,][HELLOEN=<HELLOEN>,][HELLOINT=<HELLOINT>,] [REFREDEN=<REFREDEN>,][NUMRXMTS=<NUMRXMTS>][:]; Creates a UCP neighbor

REPT ALM UCP Reports an alarm condition against a UCP object

REPT EVT UCP Reports the occurrence of a non-alarmed event against a UCP object

RTRV-ALM-UCP:[<TID>]:<AID >:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],[<SRVEFF>][,,,]; Retrieves and sends the current status of all active alarm conditions against a UCP object Output format: SID DATE TIME M CTAG COMPLD "<AID>:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,,,,:[<DESC>]" ;

RTRV-COND-UCP:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,]; Retrieves the current standing condition against a UCP object Output format: SID DATE TIME M CTAG COMPLD "<AID>:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>], [<OCRTM>],,,[<DESC>]" ;

RTRV-UCP-CC:[<TID>]:[<AID >]:<CTAG>[::::]; Retrieves UCP IP control channel attributes Output format: SID DATE TIME M CTAG COMPLD "[<AID>]::NBRIX=<NBRIX>,CCTYPE=<CCTYPE>,[PORT=<PORT>,] LOCALCCID=<LOCALCCID>,LOCALIPCC=<LOCALIPCC>, REMOTECCID=<REMOTECCID>,[REMOTEIPCC=<REMOTEIPCC>,] LMPHELLOINT=<LMPHELLOINT>,OPERLMPHELLOINT=<OPERLMPHELLOINT>, LMPHELLODEADINT=<LMPHELLODEADINT>, OPERLMPHELLODEADINT=<OPERLMPHELLODEADINT>, [TUNMD=<TUNMD>,][MTU=<MTU>,][CRCMD=<CRCMD>]" ;

RTRV-UCP-IF:[<TID>]:[<AID>]:<CTAG>[::::]; Retrieves UCP interface attributes Output format: SID DATE TIME M CTAG COMPLD "[<AID>]::NBRIX=<NBRIX>,CCID=<CCID>,LOCALIFID=<LOCALIFID>, REMOTEIFID=<REMOTEIFID>,TNATYPE=<TNATYPE>, TNAADDR=<TNAADDR>,CORENETWORKID=<CORENETWORKID>" ;

RTRV-UCP-NBR:[<TID>]:[<AID>]:<CTAG>[::::]; Retrieves a UCP neighbor Output format: SID DATE TIME M CTAG COMPLD "<AID>::[NBRIX=<NBRIX>,][NODEID=<NODEID>,][NAME=<NAME>,] [NDEN=<NDEN>,][HELLOEN=<HELLOEN>,][HELLOINT=<HELLOINT>,] [REFREDEN=<REFREDEN>,][NUMRXMTS=<NUMRXMTS>]" ;

RTRV-UCP-NODE:[<TID>]::<CTAG>[::::]; Retrieves UCP node-level attributes Output formats: SID DATE TIME M CTAG COMPLD "::[NODEID=<NODEID>,][INITRETRY=<INITRETRY>,][MAXRETRY=<MAXRETRY>,] [RESTARTTM=<RESTARTTM>,][RECOVTM=<RECOVTM>,][RXMTINT=<RXMTINT>,] [RFRSHINT=<RFRSHINT>,][RESVTIMEOUT=<RESVTIMEOUT>,] [RESVCONFTIMEOUT=<RESVCONFTIMEOUT>,] [SOURCEDIP=<SOURCEDIP>,][DESTINATIONDIP=<DESTINATIONDIP>]" ;

21  Path Protection Configuration Switching

Table 21 Path Protection Configuration Switching 

OPR-PROTNSW-<STS_PATH>:[<TID>]:<AID>:<CTAG>::<SC>[:]; Initiates a SONET path protection (path protection configuration) switch request

OPR-PROTNSW-VT1:[<TID>]:<AID>:<CTAG>::<SC>[:]; Initiates a SONET path protection switch request

REPT SW Reports the autonomous switching of a unit in a duplex equipment pair to standby and its mate to the active state

RLS-PROTNSW-<STS_PATH>:[<TID>]:<AID>:<CTAG>[::]; Releases a SONET path protection switch request that was established with the OPR-PROTNSW-<STS_PATH> command

RLS-PROTNSW-VT1:[<TID>]:<AID>:<CTAG>[::]; Releases a SONET path protection switch request that was established with the OPR-PROTNSW-VT1 command

RTRV-PROTNSW-<STS_PATH>:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the switching state of a SONET path protection configuration STS path specified in the AID Output format: SID DATE TIME M CTAG COMPLD "<AID>:<SC>,[<SWITCHTYPE>]" ;

RTRV-PROTNSW-VT1:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the switching state of a SONET path protection configuration VT path specified in the AID Output format: SID DATE TIME M CTAG COMPLD "<AID>:<SC>,[<SWITCHTYPE>]" ;