To display status
and configuration information about the Ethernet interfaces on a specific node,
use the
show controllers
command in
XR EXEC mode.
show controllers {TenGigE | TwentyFiveGigE | FortyGigE | HundredGigE | FourHundredGigE} interface-path-id [all | bert | control | internal | mac | phy | regs | stats | xgxs]
Syntax Description
{TenGigE| TwentyFiveGigE|FortyGigE|HundredGigE|FourHundredGigE}
|
Specifies the type of Ethernet interface whose status and configuration information you want to display. Enter TenGigE or HundredGigE.
|
interface-path-id
|
Physical
interface or virtual interface.
Note
|
Use the
show
interfaces command to see a list of all interfaces
currently configured on the router.
|
For more
information about the syntax for the router, use the question mark (? ) online help function.
|
all
|
Displays
detailed information for the specified interface.
|
bert
|
Displays
BERT status information for the interface.
|
control
|
Displays configuration and control information for the interface.
|
internal
|
Displays
internal information for the interface.
|
mac
|
Displays
mac information for the interface.
|
phy
|
Displays
physical information for the interface.
|
regs
|
Displays registers information for the interface.
|
stats
|
Displays
statistical information for the interface.
|
xgxs
|
Displays
information about the 10 Gigabit Ethernet Extended Sublayer (XGXS).
|
Command Default
No default
behavior or values
Command Modes
XR EXEC mode
Command History
Release
|
Modification
|
Release 7.0.12
|
This command was introduced.
|
Usage Guidelines
For the interface-path-id argument, use the following guidelines:
-
If specifying a physical interface, the naming notation is rack/slot/module/port. The slash between values is required as part of the notation. An explanation of each component of the naming notation is
as follows:
-
rack: Chassis number of the rack.
-
slot: Physical slot number of the line card.
-
module: Module number. Always 0.
-
port: Physical port number of the interface.
-
If specifying a virtual interface, the number range varies, depending on interface type.
When there is a mismatch in port speeds between peer routers, no state difference is visible in the show controller optics
command. However, during such a mismatch, the traffic route is not functional.
The interface-path-id is rack/ slot/ module/ port. The slash between values is required as part of the notation. The supported interface-path-id ranges are:
-
TenGigE
— 0/0/0/0 - 0/0/0/31
-
TwentyFiveGigE
— 0/0/0/24 - 0/0/0/31
-
FortyGigE
— 0/0/1/0 - 0/0/1/1
-
HundredGigE
— 0/0/1/0 - 0/0/1/1
Task ID
Task ID
|
Operations
|
cisco-support
|
read
Note
|
Required
in addition to the interface (read) task ID to use the
control
keyword only.
|
|
dwdm
|
read
|
interface
|
read
|
sonet-sdh
|
read
|
Examples
The following example shows sample output from the base form of the show controllers TenGigE all command:
RP/0/RP0/CPU0:router#
Operational data for interface TenGigE0/0/0/4:
State:
Administrative state: disabled
Operational state: Down (Reason: The optics for the port are not present)
LED state: Yellow On
Media:
Media type: Initializing, true state or type not yet known
No optics present
MAC address information:
Operational address: 001d.353b.975e
Burnt-in address: 001d.353b.975e
No unicast addresses in filter
No multicast addresses in filter
Autonegotiation disabled.
Operational values:
Speed: 10Gbps
Duplex: Full Duplex
Flowcontrol: None
Loopback: None (or external)
MTU: 1526
MRU: 1526
Inter-packet gap: standard (12)
BERT status for TenGigE0/0/0/4:
BERT State : DISABLED
Test Pattern : None test pattern
Time Remaining : 0
Time Interval : 0
Statistics for interface TenGigE0/0/0/4 (cached values):
Ingress:
Input total bytes = 0
Input good bytes = 0
Input total packets = 0
Input 802.1Q frames = 0
Input pause frames = 0
Input pkts 64 bytes = 0
Input pkts 65-127 bytes = 0
Input pkts 128-255 bytes = 0
Input pkts 256-511 bytes = 0
Input pkts 512-1023 bytes = 0
Input pkts 1024-1518 bytes = 0
Input pkts 1519-Max bytes = 0
Input good pkts = 0
Input unicast pkts = 0
Input multicast pkts = 0
Input broadcast pkts = 0
Input drop overrun = 0
Input drop abort = 0
Input drop unknown 802.1Q = 0
Input drop other = 0
Input error giant = 0
Input error runt = 0
Input error jabbers = 0
Input error fragments = 0
Input error CRC = 0
Input error collisions = 0
Input error symbol = 0
Input error other = 0
Input MIB giant = 0
Input MIB jabber = 0
Input MIB CRC = 0
Egress:
Output total bytes = 0
Output good bytes = 0
Output total packets = 0
Output 802.1Q frames = 0
Output pause frames = 0
Output pkts 64 bytes = 0
Output pkts 65-127 bytes = 0
Output pkts 128-255 bytes = 0
Output pkts 256-511 bytes = 0
Output pkts 512-1023 bytes = 0
Output pkts 1024-1518 bytes = 0
Output pkts 1519-Max bytes = 0
Output good pkts = 0
Output unicast pkts = 0
Output multicast pkts = 0
Output broadcast pkts = 0
Output drop underrun = 0
Output drop abort = 0
Output drop other = 0
Output error other = 0
Management information for interface TenGigE0/0/0/4:
Port number: 2
Bay number: 0
Interface handle: 0x100000c0
Config:
Auto-negotiation: Configuration not supported (Off)
Carrier delay (up): Not configured
Carrier delay (down): Not configured
Speed: Configuration not supported (10Gbps)
Duplex: Configuration not supported (Full Duplex)
Flow Control: Not configured (None)
IPG: Not configured (standard (12))
Loopback: Not configured (None)
MTU: Not configured
Soft Bandwidth: Not configured
Driver constraints:
Min MTU: 64 bytes
Max MTU: 9216 bytes
Max speed: 10Gbps
Interface type: TenGigE
Management interface: No
Promiscuous mode: Yes
Allowed config mask: 0x27b
Cached driver state:
MTU: 1522 bytes
Burnt-in MAC address: 001d.353b.975e
Bundle settings:
Aggregated: No
Bundle MTU: 1514 bytes
Bundle MAC address: 001d.353b.975e
Port FSM state:
Port is disabled, due to an admin down condition.
Complete FSM state:
Admin down
Bundle admin up
Client admin up
Client admin tx not disabled
Port disabled
Port tx disabled
Hardware link down
IDB interface state information:
IDB bundle admin up
IDB client admin up
IDB client tx admin up
IDB error disable not set
0 Unicast MAC Addresses:
0 Multicast MAC Addresses:
0 Unicast Bundle MAC Addresses:
0 Multicast Bundle MAC Addresses:
Current Data
NP(01) Version : 0003
Structure Version : 2582
XAUI Interface : B
MAC addr : 00.1d.35.3b.97.5e
RX enabled : False
TX enabled : True
Obey Pause Frames : False
TX Pause Frames : False
Pause Re-TX Period : 3000000
Min Frame Len : 60
Max Frame Len : 1526
Ignore Errors : False
Add CRC : True
Strip CRC : True
Ignore CRC Errors : False
DMA Add CRC : False
DMA Strip CRC : False
Ignore Length Error: True
Pad Short Frames : True
Min TX IFG : 12
Min RX IFG : 4
IFG Rate Control : False
Hi Gig Mode : False
Discard Ctrl Frames: True
Enable Stats Update: True
RX Stats Int Mask : 0x00000000
TX Stats Int Mask : 0x00000000
Port Number : 2
Port Type : 10GE
Transport mode : LAN
BIA MAC addr : 001d.353b.975e
Oper. MAC addr : 001d.353b.975e
Port Available : true
Status polling is : enabled
Status events are : enabled
I/F Handle : 0x100000c0
Cfg Link Enabled : disabled
H/W Tx Enable : yes
MTU : 1526
H/W Speed : 10 Gbps
H/W Duplex : Full
H/W Loopback Type : None
H/W FlowCtrl type : None
H/W AutoNeg Enable: Off
H/W Link Defects : interface is admin down
Link Up : no
Link Led Status : Shutdown
Symbol errors : 0
Serdes version : 14.42
Input good underflow : 0
Input ucast underflow : 0
Output ucast underflow : 0
Input unknown opcode underflow: 0
Pluggable Present : no
Pluggable Type : Unknown pluggable optics
Pluggable Compl. : Not Checked
Pluggable Type Supp.: Not Checked
Pluggable PID Supp. : Not Checked
Pluggable Scan Flg: false
XFP #2 is not present
Serdes Registers and info port: 2
EDC Status : 000000050 - EDC Aquiring
Rx detected : No
Block lock : No
Tx aligned : Yes
Operational data for interface HundredGigE0/2/0/0:
State:
Administrative state: disabled
Operational state: Down (Reason: State undefined)
Phy:
Media type: IEEE 802.3/802.3ae clause 30.2.5
No optics present
MAC address information:
Burnt-in address: 0000.0000.0000
Autonegotiation disabled.
Operational values:
Speed: Unknown
Duplex: Unknown
Flowcontrol: None
Loopback: None (or external)
MTU: 0
MRU: 0
Statistics for interface HundredGigE0/2/0/0 (cached values):
Ingress:
Input total bytes = 0
Input good bytes = 0
Input total packets = 0
Input 802.1Q frames = 0
Input pause frames = 0
Input pkts 64 bytes = 0
Input pkts 65-127 bytes = 0
Input pkts 128-255 bytes = 0
Input pkts 256-511 bytes = 0
Input pkts 512-1023 bytes = 0
Input pkts 1024-1518 bytes = 0
Input pkts 1519-Max bytes = 0
Input good pkts = 0
Input unicast pkts = 0
Input multicast pkts = 0
Input broadcast pkts = 0
Input drop overrun = 0
Input drop abort = 0
Input drop invalid VLAN = 0
Input drop invalid DMAC = 0
Input drop invalid encap = 0
Input drop other = 0
Input error giant = 0
Input error runt = 0
Input error jabbers = 0
Input error fragments = 0
Input error CRC = 0
Input error collisions = 0
Input error symbol = 0
Input error other = 0
Input MIB giant = 0
Input MIB jabber = 0
Input MIB CRC = 0
Egress:
Output total bytes = 0
Output good bytes = 0
Output total packets = 0
Output 802.1Q frames = 0
Output pause frames = 0
Output pkts 64 bytes = 0
Output pkts 65-127 bytes = 0
Output pkts 128-255 bytes = 0
Output pkts 256-511 bytes = 0
Output pkts 512-1023 bytes = 0
Output pkts 1024-1518 bytes = 0
Output pkts 1519-Max bytes = 0
Output good pkts = 0
Output unicast pkts = 0
Output multicast pkts = 0
Output broadcast pkts = 0
Output drop underrun = 0
Output drop abort = 0
Output drop other = 0
Output error other = 0
Management information for interface HundredGigE0/2/0/0:
Bay number: 96
Port number: 0
Interface handle: 0x1000130
Config:
Auto-negotiation: Configuration not supported (Off)
Carrier delay (up): Not configured
Carrier delay (down): Not configured
Speed: Configuration not supported (100Gbps)
Duplex: Configuration not supported (Full Duplex)
Flow Control: Configuration not supported (None)
Forward Error Correction: Not configured
IPG: Configuration not supported (standard (12))
Loopback: Not configured (None)
MTU: Not configured
Bandwidth: Not configured
BER-SD Threshold: Configuration not supported
BER-SD Report: Configuration not supported
BER-SF Threshold: Configuration not supported
BER-SF Report: Configuration not supported
BER-SF Signal Remote Failure: Configuration not supported
Driver constraints:
Min MTU: 64 bytes
Max MTU: 9216 bytes
Max speed: 100Gbps
Interface type: HundredGigE
Management interface: No
Promiscuous mode: Yes
Default carrier delay up (auto-neg on): 0 ms
Default carrier delay down (auto-neg on): 0 ms
Default carrier delay up (auto-neg off): 0 ms
Default carrier delay down (auto-neg off): 0 ms
Default carrier delay down (tx enable): 0 ms
Allowed config mask: 0x1243
Cached driver state:
MTU: 1514 bytes
Burnt-in MAC address: 089f.40ec.b120
Operational carrier delay:
Carrier delay (up): 0 ms
Carrier delay (down): 0 ms
Not a member of a bundle interface.
Port FSM state:
Port is enabled, link is up
Complete FSM state:
Admin down
Client admin down
Client admin tx not disabled
Port enabled
Port tx enabled
Hardware link up
IDB interface state information:
IDB client admin down
IDB client tx admin up
IDB error disable not set
0 Unicast MAC Addresses:
0 Multicast MAC Addresses:
The following example shows sample output from the show controllers hundredGigE control command:
RP/0/RP0/CPU0:router#
Management information for interface TenGigE0/0/0/2:
Port number: 2
Bay number: 0
Interface handle: 0x100000c0
Config:
Auto-negotiation: Configuration not supported (Off)
Carrier delay (up): Not configured
Carrier delay (down): Not configured
Speed: Configuration not supported (10Gbps)
Duplex: Configuration not supported (Full Duplex)
Flow Control: Not configured (None)
IPG: Not configured (standard (12))
Loopback: Not configured (None)
MTU: Not configured
Soft Bandwidth: Not configured
Driver constraints:
Min MTU: 64 bytes
Max MTU: 9216 bytes
Max speed: 10Gbps
Interface type: TenGigE
Management interface: No
Promiscuous mode: Yes
Allowed config mask: 0x27b
Cached driver state:
MTU: 1522 bytes
Burnt-in MAC address: 001d.353b.975e
Bundle settings:
Aggregated: No
Bundle MTU: 1514 bytes
Bundle MAC address: 001d.353b.975e
Port FSM state:
Port is disabled, due to an admin down condition.
Complete FSM state:
Admin down
Bundle admin up
Client admin up
Client admin tx not disabled
Port disabled
Port tx disabled
Hardware link down
IDB interface state information:
IDB bundle admin up
IDB client admin up
IDB client tx admin up
IDB error disable not set
0 Unicast MAC Addresses:
0 Multicast MAC Addresses:
0 Unicast Bundle MAC Addresses:
0 Multicast Bundle MAC Addresses:
Management information for interface HundredGigE0/2/0/0:
Bay number: 96
Port number: 0
Interface handle: 0x1000130
Config:
Auto-negotiation: Configuration not supported (Off)
Carrier delay (up): Not configured
Carrier delay (down): Not configured
Speed: Configuration not supported (100Gbps)
Duplex: Configuration not supported (Full Duplex)
Flow Control: Configuration not supported (None)
Forward Error Correction: Not configured
IPG: Configuration not supported (standard (12))
Loopback: Not configured (None)
MTU: Not configured
Bandwidth: Not configured
BER-SD Threshold: Configuration not supported
BER-SD Report: Configuration not supported
BER-SF Threshold: Configuration not supported
BER-SF Report: Configuration not supported
BER-SF Signal Remote Failure: Configuration not supported
Driver constraints:
Min MTU: 64 bytes
Max MTU: 9216 bytes
Max speed: 100Gbps
Interface type: HundredGigE
Management interface: No
Promiscuous mode: Yes
Default carrier delay up (auto-neg on): 0 ms
Default carrier delay down (auto-neg on): 0 ms
Default carrier delay up (auto-neg off): 0 ms
Default carrier delay down (auto-neg off): 0 ms
Default carrier delay down (tx enable): 0 ms
Allowed config mask: 0x1243
Cached driver state:
MTU: 1514 bytes
Burnt-in MAC address: 089f.40ec.b120
Operational carrier delay:
Carrier delay (up): 0 ms
Carrier delay (down): 0 ms
Not a member of a bundle interface.
Port FSM state:
Port is enabled, link is up
Complete FSM state:
Admin down
Client admin down
Client admin tx not disabled
Port enabled
Port tx enabled
Hardware link up
IDB interface state information:
IDB client admin down
IDB client tx admin up
IDB error disable not set
0 Unicast MAC Addresses:
0 Multicast MAC Addresses:
The following example shows sample output from the show controllers TenGigE regs command:
RP/0/RP0/CPU0:router# show controllers tenGigE 0/0/0/1 regs
MAC Registers for port: 1
GE MAC CFG (#0954): 704c5e5a
GPCS Config (#0147): 00000f08
GPCS Status (#0236): 000000ca
GSERDES Status (#0237): 0007fe09
RP/0/RP0/CPU0:router# show controllers tenGigE 0/0/0/4 regs
MAC Registers for port: 0
CONFIG1 (#1034): 03100a1a
CONFIG2 (#1035): 040c2398
CONTROL (#1036): 00000000
ADDRESS_LOW (#1037): 53ffa780
ADDRESS_HIGH (#1038): 0000001b
MII_MGMT_CONFIG (#1039): 00000007
MII_MGMT_CMD (#1040): 00000000
MII_MGMT_ADDRESS (#1041): 00000000
MII_MGMT_DATA (#1042): 40000000
STAT_CONFIG (#1043): 00000007
MASK_R (#1044): 00000000
MASK_T (#1045): 00000000
COMP (#1046): 00100d24
MAC_CONFIG (#1047): ffffffff
INTERRUPT_C (#1048): 00000000
The following example shows sample output from the show controllers hundredGigE stats command:
RP/0/RP0/CPU0:router#
Statistics for interface TenGigE0/0/0/0 (cached values):
Ingress:
Input total bytes = 9614339316
Input good bytes = 9614339316
Input total packets = 106713557
Input 802.1Q frames = 0
Input pause frames = 0
Input pkts 64 bytes = 103907216
Input pkts 65-127 bytes = 2494185
Input pkts 128-255 bytes = 3410
Input pkts 256-511 bytes = 3406
Input pkts 512-1023 bytes = 2
Input pkts 1024-1518 bytes = 0
Input pkts 1519-Max bytes = 305338
Input good pkts = 106713557
Input unicast pkts = 105627141
Input multicast pkts = 1086414
Input broadcast pkts = 2
Input drop overrun = 0
Input drop abort = 0
Input drop unknown 802.1Q = 0
Input drop other = 0
Input error giant = 0
Input error runt = 0
Input error jabbers = 0
Input error fragments = 0
Input error CRC = 0
Input error collisions = 0
Input error symbol = 0
Input error other = 0
Input MIB giant = 305338
Input MIB jabber = 0
Input MIB CRC = 0
Egress:
Output total bytes = 15202682421
Output good bytes = 15202682421
Output total packets = 107534855
Output 802.1Q frames = 0
Output pause frames = 0
Output pkts 64 bytes = 103862713
Output pkts 65-127 bytes = 2448054
Output pkts 128-255 bytes = 308716
Output pkts 256-511 bytes = 6
Output pkts 512-1023 bytes = 13
Output pkts 1024-1518 bytes = 0
Output pkts 1519-Max bytes = 915353
Output good pkts = 107534855
Output unicast pkts = 105321133
Output multicast pkts = 1298368
Output broadcast pkts = 1
Output drop underrun = 0
Output drop abort = 0
Output drop other = 0
Output error other = 0
Statistics for interface HundredGigE0/2/0/0 (cached values):
Ingress:
Input total bytes = 0
Input good bytes = 0
Input total packets = 0
Input 802.1Q frames = 0
Input pause frames = 0
Input pkts 64 bytes = 0
Input pkts 65-127 bytes = 0
Input pkts 128-255 bytes = 0
Input pkts 256-511 bytes = 0
Input pkts 512-1023 bytes = 0
Input pkts 1024-1518 bytes = 0
Input pkts 1519-Max bytes = 0
Input good pkts = 0
Input unicast pkts = 0
Input multicast pkts = 0
Input broadcast pkts = 0
Input drop overrun = 0
Input drop abort = 0
Input drop invalid VLAN = 0
Input drop invalid DMAC = 0
Input drop invalid encap = 0
Input drop other = 0
Input error giant = 0
Input error runt = 0
Input error jabbers = 0
Input error fragments = 0
Input error CRC = 0
Input error collisions = 0
Input error symbol = 0
Input error other = 0
Input MIB giant = 0
Input MIB jabber = 0
Input MIB CRC = 0
Egress:
Output total bytes = 0
Output good bytes = 0
Output total packets = 0
Output 802.1Q frames = 0
Output pause frames = 0
Output pkts 64 bytes = 0
Output pkts 65-127 bytes = 0
Output pkts 128-255 bytes = 0
Output pkts 256-511 bytes = 0
Output pkts 512-1023 bytes = 0
Output pkts 1024-1518 bytes = 0
Output pkts 1519-Max bytes = 0
Output good pkts = 0
Output unicast pkts = 0
Output multicast pkts = 0
Output broadcast pkts = 0
Output drop underrun = 0
Output drop abort = 0
Output drop other = 0
Output error other = 0