IP-to-IP Gateway SIP-to-SIP Basic Functionality

Last Updated: December 3, 2012

SIP-to-SIP Basic Functionality for Cisco Unified Border Element (Cisco UBE) and Cisco Unified Border Element (Enterprise) (Cisco UBE (Enterprise)) provides termination and reorigination of both signaling and media between VoIP and video networks using SIP signaling in conformance with RFC3261. The SIP-to-SIP protocol interworking capabilities support the following:

  • Basic voice calls (Supported audio codecs include: G.711, G.729, G.728, G.726, G.723, G.722, gsmamr nb, AAC_LD, iLBC. Video codecs: H.263, and H.264)
  • Calling/called name and number
  • DTMF relay interworking
    • SIP RFC 2833 <-> SIP RFC 2833
    • SIP Notify <-> SIP Notify
  • Interworking between SIP early-media and SIP early-media signaling
  • Interworking between SIP delayed-media and SIP delayed-media signaling
  • RADIUS call-accounting records
  • RSVP synchronized with call signaling
  • SIP-to-SIP Video calls
  • TCL IVR 2.0 for SIP, including media playout and digit collection (RFC 2833 DTMF relay)
  • T.38 fax relay and Cisco fax relay
  • UDP and TCP transport

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.

Prerequisites for IP-to-IP Gateway SIP-to-SIP Basic Functionality

Cisco Unified Border Element

  • Cisco IOS Release 12.2(13)T3 or a later release must be installed and running on your Cisco Unified Border Element.

Cisco Unified Border Element (Enterprise)

  • Cisco IOS XE Release 2.5 or a later release must be installed and running on your Cisco ASR 1000 Series Router.

Restrictions for IP-to-IP Gateway SIP-to-SIP Basic Functionality

  • Connections are disabled by default in Cisco IOS images that support the Cisco UBE (Enterprise).

How to Configure SIP-to-SIP Connections in a Cisco Unified Border Element Enterprise

To configure SIP-to-SIP connection types, perform the steps in this section.

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    voice service voip

4.    allow-connections from-type to to-type

5.    exit


DETAILED STEPS
  Command or Action Purpose
Step 1
enable


Example:

Device> enable

 

Enables privileged EXEC mode.

  • Enter your password if prompted.
 
Step 2
configure terminal


Example:

Device# configure terminal

 

Enters global configuration mode.

 
Step 3
voice service voip


Example:

Device(config)# voice service voip

 

Enters VoIP voice-service configuration mode.

 
Step 4
allow-connections from-type to to-type


Example:

Device(config-voi-serv)# allow-connections sip to sip

 

Allows connections between specific types of endpoints in an Cisco UBE. Arguments are as follows:

  • from-type --Type of connection. Valid values: h323, sip.
  • to-type --Type of connection. Valid values: h323, sip.
Note    H.323-to-H.323: By default, H.323-to-H.323 connections are disabled and POTS-to-any and any-to-POTS connections are enabled.
 
Step 5
exit


Example:

Device(config-voi-serv)# exit

 

Exits the current mode.

 

Feature Information for IP-to-IP Gateway SIP-to-SIP Basic Functionality

The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.

Table 1 Feature Information for IP-to-IP Gateway: SIP-to-SIP Basic Functionality

Feature Name

Releases

Feature Information

SIP-to-SIP Basic Functionality

12.2(13)T3

12.3(7)T

This feature provides termination and reorigination of both signaling and media between VoIP and video networks using SIP signaling in conformance with RFC3261.

In Cisco IOS Release 12.2(13)T3, this feature was implemented on the Cisco Unified Border Element.

The following commands were introduced or modified: allow-connections

SIP-to-SIP Basic Functionality

Cisco IOS XE Release 2.5

This feature provides termination and reorigination of both signaling and media between VoIP and video networks using SIP signaling in conformance with RFC3261.

In Cisco IOS Release 12.2(13)T3, this feature was implemented on the Cisco Unified Border Element (Enterprise).

The following commands were introduced or modified: allow-connections

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

© 2012 Cisco Systems, Inc. All rights reserved.