IPv6 over IPv4 GRE Tunnel Protection

The IPv6 over IPv4 GRE Tunnel Protection feature allows both IPv6 unicast and multicast traffic to pass through a protected generic routing encapsulation (GRE) tunnel.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.

Prerequisites for IPv6 over IPv4 GRE Tunnel Protection

  • To enable this feature, you must configure IPsec tunnel protection on an IPv4 GRE tunnel.

  • To enable IPv6 multicast, you must configure IPv6 multicast routing.

Restrictions for IPv6 over IPv4 GRE Tunnel Protection

The IPv6 over IPv4 GRE Tunnel Protection feature supports IPv6 over IPv4 point-to-point GRE tunnel protection and not IPv6 over IPv4 mGRE tunnel protection.

Information About IPv6 over IPv4 GRE Tunnel Protection

GRE Tunnels with IPsec

Generic routing encapsulation (GRE) tunnels sometimes are combined with IPSec, because IPSec does not support IPv6 multicast packets. This function prevents dynamic routing protocols from running successfully over an IPSec VPN network. Because GRE tunnels do support IPv6 multicast , a dynamic routing protocol can be run over a GRE tunnel. Once a dynamic routing protocol is configured over a GRE tunnel, you can encrypt the GRE IPv6 multicast packets using IPSec.

IPSec can encrypt GRE packets using a crypto map or tunnel protection. Both methods specify that IPSec encryption is performed after GRE encapsulation is configured. When a crypto map is used, encryption is applied to the outbound physical interfaces for the GRE tunnel packets. When tunnel protection is used, encryption is configured on the GRE tunnel interface.

The following figure shows encrypted packets that enter a router through a GRE tunnel interface using a crypto map on the physical interface. Once the packets are decrypted and decapsulated, they continue to their IP destination as clear text.

Figure 1. Using a Crypto Map to Configure IPv6 over IPv4 GRE Tunnel Encryption

The following figure shows encryption using tunnel protection command on the GRE tunnel interface. The encrypted packets enter the router through the tunnel interface and are decrypted and decapsulated before they continue to their destination as clear text.

Figure 2. Using Tunnel Protection to Configure IPv6 over IPv4 GRE Tunnel Encryption

There are two key differences in using the crypto map and tunnel protection methods:

  • The IPSec crypto map is tied to the physical interface and is checked as packets are forwarded out through the physical interface. At this point, the GRE tunnel has already encapsulated the packet.

  • Tunnel protection ties the encryption functionality to the GRE tunnel and is checked after the packet is GRE encapsulated but before the packet is handed to the physical interface.

How to Configure IPv6 over IPv4 GRE Tunnel Protection

Configuring IPv6 over IPv4 GRE Encryption Using a Crypto Map

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. ipv6 multicast-routing
  4. ipv6 unicast-routing
  5. interface type number
  6. ipv6 address {ipv6-address/prefix-length | prefix-name sub-bits/prefix-length}
  7. tunnel mode {aurp | cayman | dvmrp | eon | gre | gre multipoint | gre ip | gre ipv6 | ipip [decapsulate-any] | ipsec ipv4 | iptalk | ipv6 | ipsec ipv6 | mpls | nos | rbscp}
  8. tunnel source {ip-address | ipv6-address | interface-typeinterface-number}
  9. tunnel destination {hostname | ip-address | ipv6-address}
  10. exit
  11. crypto isakmp policy priority
  12. authentication {rsa-sig | rsa-encr | pre-share}
  13. hash {sha | md5}
  14. group {1 | 2 | 5}
  15. encryption {des | 3des | aes 192 | aes 256}
  16. exit
  17. crypto isakmp key enc-type-digit keystring {address peer-address [mask] | ipv6 {ipv6-address/ipv6-prefix} | hostname hostname} [no-xauth]
  18. crypto ipsec transform-set transform-set-name transform1 [transform2] [transform3] [transform4]
  19. access-list access-list-number [dynamic dynamic-name [timeout minutes]] {deny | permit} protocol source source-wildcard destination destination-wildcard [precedence precedence] [tos tos] [time-range time-range-name] [fragments] [log [word] | log-input [word]]
  20. crypto map [ipv6] map-name seq-num [ipsec-isakmp [dynamic dynamic-map-name | discover | profile profile-name]]
  21. set peer {hostname [dynamic] [default] | ip-address [default]}
  22. set transform-set transform-set-name [transform-set-name2...transform-set-name6]
  23. match address [access-list-id | name]
  24. exit
  25. interface type number
  26. crypto map map-name [redundancy standby-group-name [stateful]]
  27. end

DETAILED STEPS

  Command or Action Purpose
Step 1

enable

Example:

Router> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3

ipv6 multicast-routing

Example:

Router(config)# ipv6 multicast-routing

Enables multicast routing using Protocol Independent Multicast (PIM) and Multicast Listener Discovery (MLD) on all IPv6-enabled interfaces of the router and enables multicast forwarding.

  • Enable this command only if you are using IPv6 multicast. If you are using IPv6 unicast, you need not enable this command.

Step 4

ipv6 unicast-routing

Example:

Router(config)# ipv6 unicast-routing

Enables the forwarding of IPv6 unicast datagrams.

Step 5

interface type number

Example:

Router(config)# interface tunnel 10

Specifies a tunnel interface and number, and enters interface configuration mode.

Step 6

ipv6 address {ipv6-address/prefix-length | prefix-name sub-bits/prefix-length}

Example:

Router(config-if)# ipv6 address 0:0:0:7272::72/64

Configures an IPv6 address based on an IPv6 general prefix and enables IPv6 processing on an interface.

Step 7

tunnel mode {aurp | cayman | dvmrp | eon | gre | gre multipoint | gre ip | gre ipv6 | ipip [decapsulate-any] | ipsec ipv4 | iptalk | ipv6 | ipsec ipv6 | mpls | nos | rbscp}

Example:

Router(config-if)# tunnel mode gre ip

Sets the encapsulation mode for the tunnel interface.

Step 8

tunnel source {ip-address | ipv6-address | interface-typeinterface-number}

Example:

Router(config-if)# tunnel source ethernet0

Sets the source address for a tunnel interface.

Step 9

tunnel destination {hostname | ip-address | ipv6-address}

Example:

Router(config-if)# tunnel destination 172.16.0.12

Specifies the destination for a tunnel interface.

Step 10

exit

Example:

Router(config-if)# exit

Exits interface configuration mode and returns to global configuration mode.

Step 11

crypto isakmp policy priority

Example:

Router(config)# crypto isakmp policy 15

Defines an Internet Key Exchange (IKE) policy, and enters ISAKMP policy configuration mode.

  • Policy number 1 indicates the policy with the highest priority. The lower the priority argument value, the higher the priority.

Step 12

authentication {rsa-sig | rsa-encr | pre-share}

Example:

Router(config-isakmp-policy)# authentication pre-share

Specifies the authentication method within an IKE policy.

  • The rsa-sig and rsa-encr keywords are not supported in IPv6.

Step 13

hash {sha | md5}

Example:

Router(config-isakmp-policy)# hash md5

Specifies the hash algorithm within an IKE policy.

Step 14

group {1 | 2 | 5}

Example:

Router(config-isakmp-policy)# group 2

Specifies the Diffie-Hellman group identifier within an IKE policy.

Step 15

encryption {des | 3des | aes 192 | aes 256}

Example:

Router(config-isakmp-policy)# encryption 3des

Specifies the encryption algorithm within an IKE policy.

Step 16

exit

Example:

Router(config-isakmp-policy)# exit

Exits ISAKMP policy configuration mode and enters global configuration mode.

Step 17

crypto isakmp key enc-type-digit keystring {address peer-address [mask] | ipv6 {ipv6-address/ipv6-prefix} | hostname hostname} [no-xauth]

Example:

Router(config)# crypto isakmp key cisco-10 address 172.16.0.12 255.240.0.0

Configures a preshared authentication key.

Step 18

crypto ipsec transform-set transform-set-name transform1 [transform2] [transform3] [transform4]

Example:

Router(config)# crypto ipsec transform-set myset0 ah-sha-hmac esp-3des

Defines a transform set.

Step 19

access-list access-list-number [dynamic dynamic-name [timeout minutes]] {deny | permit} protocol source source-wildcard destination destination-wildcard [precedence precedence] [tos tos] [time-range time-range-name] [fragments] [log [word] | log-input [word]]

Example:

Router(config)# access-list 110 permit gre host 192.168.0.16 host 172.16.0.12

Defines an extended IP access list.

Step 20

crypto map [ipv6] map-name seq-num [ipsec-isakmp [dynamic dynamic-map-name | discover | profile profile-name]]

Example:

Router(config)# crypto map mymap 10 ipsec-isakmp

Creates a new crypto map entry or profile and enters crypto map configuration mode.

Step 21

set peer {hostname [dynamic] [default] | ip-address [default]}

Example:

Router(config-crypto-map)# set peer 10.0.0.1

Specifies an IP Security (IPsec) peer in a crypto map entry.

Step 22

set transform-set transform-set-name [transform-set-name2...transform-set-name6]

Example:

Router(config-crypto-map)# set transform-set myset0

Specifies the transform set that can be used with the crypto map entry.

Step 23

match address [access-list-id | name]

Example:

Router(config-crypto-map)# match address 102

Specifies an extended access list for a crypto map entry.

Step 24

exit

Example:

Router(config-crypto-map)# exit

Exits crypto map configuration mode and returns to global configuration mode.

Step 25

interface type number

Example:

Router(config)# interface ethernet 1

Specifies an interface and number and enters interface configuration mode.

Step 26

crypto map map-name [redundancy standby-group-name [stateful]]

Example:

Router(config-if)# crypto map mymap

Applies a previously defined crypto map set to an outbound interface.

Step 27

end

Example:

Router(config-if)# end

Exits interface configuration mode and returns to privileged EXEC mode.

Configuring IPv6 over IPv4 GRE Encryption Using Tunnel Protection

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. ipv6 multicast-routing
  4. ipv6 unicast-routing
  5. crypto isakmp policy priority
  6. authentication {rsa-sig | rsa-encr | pre-share}
  7. hash {sha | md5}
  8. group {1 | 2 | 5}
  9. encryption {des | 3des | aes | aes 192 | aes 256}
  10. exit
  11. crypto isakmp key enc-type-digit keystring {address peer-address [mask] | ipv6 {ipv6-address/ipv6-prefix} | hostname hostname} [no-xauth]
  12. crypto ipsec transform-set transform-set-name transform1 [transform2 ] [transform3 ] [transform4 ]
  13. crypto ipsec profile profile-name
  14. set transform-set transform-set-name [transform-set-name2...transform-set-name6]
  15. exit
  16. interface type number
  17. ipv6 address {ipv6-address / prefix-length | prefix-name sub-bits /prefix-length }
  18. tunnel mode {aurp | cayman | dvmrp | eon | gre | gre multipoint | gre ip | gre ipv6 | ipip[decapsulate-any] | ipsec ipv4 | iptalk | ipv6 | ipsec ipv6 | mpls | nos | rbscp}
  19. tunnel source {ip-address | ipv6-address | interface-type interface-number }
  20. tunnel destination {hostname | ip-address | ipv6-address}
  21. tunnel protection ipsec profile name [shared]
  22. end

DETAILED STEPS

  Command or Action Purpose
Step 1

enable

Example:

Router> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3

ipv6 multicast-routing

Example:

Router(config)# ipv6 multicast-routing

Enables multicast routing using Protocol Independent Multicast (PIM) and Multicast Listener Discovery (MLD) on all IPv6-enabled interfaces of the router and enables multicast forwarding.

  • Enable this command only if you are using IPv6 multicast. If you are using IPv6 unicast, you do not need to enable this command.

Step 4

ipv6 unicast-routing

Example:

Router(config)# ipv6 unicast-routing

Enables the forwarding of IPv6 unicast datagrams.

Step 5

crypto isakmp policy priority

Example:

Router(config)# crypto isakmp policy 15

Defines an IKE policy, and enters ISAKMP policy configuration mode.

Policy number 1 indicates the policy with the highest priority. The lower the priority argument value, the higher the priority.

Step 6

authentication {rsa-sig | rsa-encr | pre-share}

Example:

Router(config-isakmp-policy)# authentication pre-share

Specifies the authentication method within an Internet Key Exchange (IKE) policy.

  • The rsa-sig and rsa-encr keywords are not supported in IPv6.

Step 7

hash {sha | md5}

Example:

Router(config-isakmp-policy)# hash md5

Specifies the hash algorithm within an IKE policy.

Step 8

group {1 | 2 | 5}

Example:

Router(config-isakmp-policy)# group 2

Specifies the Diffie-Hellman group identifier within an IKE policy.

Step 9

encryption {des | 3des | aes | aes 192 | aes 256}

Example:

Router(config-isakmp-policy)# encryption 3des

Specifies the encryption algorithm within an IKE policy.

Step 10

exit

Example:

Router(config-isakmp-policy)# exit

Exits ISAKMP policy configuration mode and returns to global configuration mode.

Step 11

crypto isakmp key enc-type-digit keystring {address peer-address [mask] | ipv6 {ipv6-address/ipv6-prefix} | hostname hostname} [no-xauth]

Example:

Router(config)# crypto isakmp key cisco-10 address 172.16.0.12 255.240.0.0

Configures a preshared authentication key.

Step 12

crypto ipsec transform-set transform-set-name transform1 [transform2 ] [transform3 ] [transform4 ]

Example:

Router(config)# crypto ipsec transform-set myset0 ah-sha-hmac esp-3des

Defines a transform set, and places the router in crypto transform configuration mode.

Step 13

crypto ipsec profile profile-name

Example:

Router(config)# crypto ipsec profile ipsecprof

Defines the IPsec parameters that are to be used for IPsec encryption between two IPsec routers and enters IPsec profile configuration mode.

Step 14

set transform-set transform-set-name [transform-set-name2...transform-set-name6]

Example:

Router(ipsec-profile)# set transform-set myset0

Specifies the transform set that can be used with the crypto map entry.

Step 15

exit

Example:

Router(ipsec-profile)# exit

Exits IPsec profile configuration mode and returns to global configuration mode.

Step 16

interface type number

Example:

Router(config)# interface tunnel 1

Specifies a tunnel interface and number and enters interface configuration mode.

Step 17

ipv6 address {ipv6-address / prefix-length | prefix-name sub-bits /prefix-length }

Example:

Router(config-if)# ipv6 address 3ffe:b00:c18:1::3/127

Specifies the IPv6 network assigned to the interface and enables IPv6 processing on the interface.

Step 18

tunnel mode {aurp | cayman | dvmrp | eon | gre | gre multipoint | gre ip | gre ipv6 | ipip[decapsulate-any] | ipsec ipv4 | iptalk | ipv6 | ipsec ipv6 | mpls | nos | rbscp}

Example:

Router(config-if)# tunnel mode gre ip

Specifies a GRE IPv6 tunnel.

Step 19

tunnel source {ip-address | ipv6-address | interface-type interface-number }

Example:

Router(config-if)# tunnel source 10.0.0.1

Specifies the source address or the source interface type and number for the tunnel interface.

Step 20

tunnel destination {hostname | ip-address | ipv6-address}

Example:

Router(config-if)# tunnel destination 172.16.0.12

Specifies the destination address or hostname for the tunnel interface.

Step 21

tunnel protection ipsec profile name [shared]

Example:

Router(config-if)# tunnel protection ipsec profile ipsecprof

Associates a tunnel interface with an IPsec profile.

Step 22

end

Example:

Router(config-if)# end

Exits interface configuration mode and returns to privileged EXEC mode.

Configuration Examples for IPv6 over IPv4 GRE Tunnel Protection

Example: Configuring IPv6 over IPv4 GRE Encryption Using a Crypto Map

Router> enable
Router# configure terminal
Router(config)# ipv6 multicast-routing
Router(config)# ipv6 unicast-routing
Router(config)# interface tunnel 10
Router(config-if)# ipv6 address my-prefix 0:0:0:7272::72/64
Router(config-if)# tunnel mode gre ip
Router(config-if)# tunnel source ethernet0
Router(config-if)# tunnel destination 172.16.0.12
Router(config-if)# exit
Router(config)# crypto isakmp policy 15
Router(config-isakmp-policy)# authentication pre-share
Router(config-isakmp-policy)# hash md5
Router(config-isakmp-policy)# group 2
Router(config-isakmp-policy)# encryption 3des
Router(config-isakmp-policy)# exit
Router(config)# crypto isakmp key cisco-10 address 172.16.0.12 255.240.0.0
Router(config)# crypto ipsec transform-set myset0 ah-sha-hmac esp-3des
Router(config)# access-list 110 permit gre host 192.168.0.16 host 172.16.0.12
Router(config)# crypto map mymap 10 ipsec-isakmp
Router(config-crypto-map)# set peer 10.0.0.1
Router(config-crypto-map)# set transform-set myset0
Router(config-crypto-map)# match address 102
Router(config-crypto-map)# exit
Router(config)# interface ethernet1
Router(config-if)# crypto map mymap
Router(config-if)# end

Example: Configuring IPv6 over IPv4 GRE Encryption Using Tunnel Protection

The following example configures IPsec tunnel protection on an IPv4 GRE tunnel. IPv6 multicast routing is enabled using the ipv6 multicast-routing command.
Router> enable
Router# configure terminal
Router(config)# ipv6 multicast-routing
Router(config)# ipv6 unicast-routing
Router(config)# crypto isakmp policy 15
Router(config-isakmp-policy)# authentication pre-share
Router(config-isakmp-policy)# hash md5
Router(config-isakmp-policy)# group 2
Router(config-isakmp-policy)# encryption 3des
Router(config-isakmp-policy)# exit
Router(config)# crypto isakmp key cisco-10 address 172.16.0.12 255.240.0.0
Router(config)# crypto ipsec transform-set myset0 ah-sha-hmac esp-3des
Router(config)# crypto ipsec profile ipsecprof
Router(ipsec-profile)# set transform-set myset0
Router(ipsec-profile)# exit
Router(config)# interface tunnel 1
Router(config-if)# ipv6 address 3ffe:b00:c18:1::3/127
Router(config-if)# tunnel mode gre ip
Router(config-if)# tunnel source 10.0.0.1
Router(config-if)# tunnel destination 172.16.0.12
Router(config-if)# tunnel protection ipsec profile ipsecprof
Router(config-if)# end

Additional References

Related Documents

Related Topic

Document Title

IPv6 Multicast Routing

IPv6 Implementation Guide

Cisco IOS commands

Cisco IOS Master Commands List, All Releases

Security commands: complete command syntax, command mode, command history, defaults, usage guidelines, and examples

Technical Assistance

Description

Link

The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

http://www.cisco.com/cisco/web/support/index.html

Feature Information for IPv6 over IPv4 GRE Tunnel Protection

The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.