BGP Attribute Filter and Enhanced Attribute Error Handling

The BGP Attribute Filter feature allows you to “treat-as-withdraw” updates that contain specific path attributes. The prefixes contained in the update are removed from the routing table. The feature also allows you to remove specific path attributes from incoming updates. Both behaviors provide an increased measure of security. The BGP Enhanced Attribute Error Handling feature prevents peer sessions from flapping due to errors from any malformed update, thereby saving resources.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Information About BGP Attribute Filtering

BGP Attribute Filter and Enhanced Attribute Error Handling

The BGP Attribute Filter feature provides two ways to achieve an increased measure of security:

  • The feature allows you to treat-as-withdraw an Update coming from a specified neighbor if the Update contains a specified attribute type. When an Update is treat-as-withdraw, the prefixes in the Update are removed from the BGP routing table (if they existed in the routing table).

  • The feature also allows you to drop specified path attributes from an Update, and then the system processes the rest of the Update as usual.

The BGP Enhanced Attribute Error Handling feature prevents peer sessions from flapping due to a malformed Update. The malformed Update is treat-as-withdraw and does not cause the BGP session to be reset. This feature is enabled by default, but can be disabled.

The features are implemented in the following order:

  1. Received Updates that contain user-specified path attributes are treat-as-withdraw (as long as the NLRI can be parsed successfully). If there is an existing prefix in the BGP routing table, it will be removed. The neighbor path-attribute treat-as-withdraw command configures this feature.

  2. User-specified path attributes are discarded from received Updates, and the rest of the Update is processed normally. The neighbor path-attribute discard command configures this feature.

  3. Received Updates that are malformed are treat-as-withdraw. This feature is enabled by default; it can be disabled by configuring the no bgp enhanced-error command.

Details About Specifying Attributes as Treat-as-Withdraw

Attribute types 1, 2, 3, 4, 8, 14, 15, and 16 cannot be configured for path attribute treat-as-withdraw.

Attribute type 5 (localpref), type 9 (Originator,) and type 10 (Cluster-id) can be configured for treat-as-withdraw for eBGP neighbors only.

Configuring path attributes to be treated as withdrawn will trigger an inbound Route Refresh to ensure that the routing table is up to date.

Details About Specifying Attributes as Discard

Attribute types 1, 2, 3, 4, 8, 14, 15, and 16 cannot be configured for path attribute discard.

Attribute type 5 (localpref), type 9 (Originator), and type 10 (Cluster-id) can be configured for discard for eBGP neighbors only.

Configuring path attributes to be discarded will trigger an inbound Route Refresh to ensure that the routing table is up to date.

Details About Enhanced Attribute Error Handling

If a malformed Update is received, it is treat-as-withdraw to prevent peer sessions from flapping due to the processing of BGP path attributes. This feature applies to eBGP and iBGP peers. This feature is enabled by default; it can be disabled.

If the BGP Enhanced Attribute Error Handling feature is enabled or disabled, BGP places the MP_REACH attribute (attribute 14) at the beginning of an attribute list while formatting an update. Enhanced attribute error handling functions more easily when the MP_REACH attribute is at the beginning of the attribute list.

How to Filter BGP Path Attributes

Treat-as-Withdraw BGP Updates Containing a Specified Path Attribute


Note


Performing this task will trigger an inbound Route Refresh to ensure that the routing table is up to date.


SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    router bgp as-number

    4.    neighbor {ip-address | ipv6-address} path-attribute treat-as-withdraw {attribute-value | range start-value end-value} in

    5.    Repeat Step 4 to configure other attributes not in a range or to configure a different neighbor.

    6.    end


DETAILED STEPS
     Command or ActionPurpose
    Step 1 enable


    Example:
    Device> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.

     
    Step 2 configure terminal


    Example:
    Device# configure terminal
     

    Enters global configuration mode.

     
    Step 3 router bgp as-number


    Example:
    Device(config)# router bgp 65000
     

    Configures a BGP routing process and enters router configuration mode.

     
    Step 4 neighbor {ip-address | ipv6-address} path-attribute treat-as-withdraw {attribute-value | range start-value end-value} in


    Example:
    Device(config-router)# neighbor 2001:DB8:1::1 path-attribute treat-as-withdraw 100 in
     

    Treat-as-withdraw any incoming Update messages that contain the specified path attribute or range of path attributes.

    • Any prefixes in an Update that is treat-as-withdraw are removed from the BGP routing table.

    • The specific attribute value and the range of attribute values are independent of each other.

     
    Step 5Repeat Step 4 to configure other attributes not in a range or to configure a different neighbor.    
    Step 6end


    Example:
    Device(config-router)# end
     

    Exits to privileged EXEC mode.

     

    Discarding Specific Path Attributes from an Update Message


    Note


    Performing this task will trigger an inbound Route Refresh to ensure that the routing table is up to date.


    SUMMARY STEPS

      1.    enable

      2.    configure terminal

      3.    router bgp as-number

      4.    neighbor {ip-address | ipv6-address} path-attribute discard {attribute-value | range start-value end-value} in

      5.    Repeat Step 4 to configure other attributes not in a range or to configure a different neighbor.

      6.    end


    DETAILED STEPS
       Command or ActionPurpose
      Step 1 enable


      Example:
      Device> enable
       

      Enables privileged EXEC mode.

      • Enter your password if prompted.

       
      Step 2 configure terminal


      Example:
      Device# configure terminal
       

      Enters global configuration mode.

       
      Step 3 router bgp as-number


      Example:
      Device(config)# router bgp 6500
       

      Configures a BGP routing process and enters router configuration mode.

       
      Step 4 neighbor {ip-address | ipv6-address} path-attribute discard {attribute-value | range start-value end-value} in


      Example:
      Device(config-router)# neighbor 2001:DB8:1::1 path-attribute discard 128 in
       

      Drops specified path attributes from Update messages from the specified neighbor.

       
      Step 5Repeat Step 4 to configure other attributes not in a range or to configure a different neighbor.

      Example:

       

       
      Step 6end


      Example:
      Device(config-router)# end
       

      Exits to privileged EXEC mode.

       

      Displaying Withdrawn or Discarded Path Attributes

      Perform any of these steps in any order to display information about treat-as-withdraw, discarded, or unknown path attributes. You can use the show ip bgp command with any address family that BGP supports, such as show ip bgp ipv4 multicast, show ip bgp ipv6 unicast, etc.

      SUMMARY STEPS

        1.    enable

        2.    show ip bgp neighbor [ip-address | ipv6-address]

        3.    show ip bgp path-attribute unknown

        4.    show ip bgp path-attribute discard

        5.    show ip bgp vpnv4 all prefix

        6.    show ip bgp neighbors prefix


      DETAILED STEPS
         Command or ActionPurpose
        Step 1 enable


        Example:
        Device> enable
         

        Enables privileged EXEC mode.

        • Enter your password if prompted.

         
        Step 2show ip bgp neighbor [ip-address | ipv6-address]

        Example:
        Device# show ip bgp neighbor 2001:DB8:1::1
         

        (Optional) Displays the configured discard and treat-as-withdraw attribute values for the neighbor, counts of Updates with such attributes discarded or treat-as-withdraw, and the count of malformed treat-as-withdraw Updates.

         
        Step 3show ip bgp path-attribute unknown


        Example:
        Device# show ip bgp path-attribute unknown
         

        (Optional) Displays all prefixes that have an unknown attribute.

         
        Step 4show ip bgp path-attribute discard


        Example:
        Device# show ip bgp path-attribute discard
         

        (Optional) Displays all prefixes for which an attribute has been discarded.

         
        Step 5show ip bgp vpnv4 all prefix


        Example:
        Device# show ip bgp vpnv4 all 192.168.1.0
         

        (Optional) Displays the unknown attributes and discarded attributes associated with a prefix.

         
        Step 6show ip bgp neighbors prefix


        Example:
        Device# show ip bgp neighbors 192.168.1.0
         

        (Optional) Displays the configured discard and treat-as-withdraw attributes associated with a prefix.

         

        Configuration Examples for BGP Attribute Filter

        Examples: Withdraw Updates Based on Path Attribute

        The following example shows how to configure the device to treat-as-withdraw any Update messages from the specified neighbor that contain the unwanted path attribute 100 or 128:

        router bgp 65600
         neighbor 2001:DB8:1::2 path-attribute treat-as-withdraw 100 in
         neighbor 2001:DB8:1::2 path-attribute treat-as-withdraw 128 in
              

        The following example shows how to configure the device to treat-as-withdraw any Update messages from the specified neighbor that contain the unwanted path attributes in the range from 21 to 255:

        router bgp 65600
         neighbor 2001:DB8:1::2 path-attribute treat-as-withdraw 21 255 in
         
              

        Examples: Discard Path Attributes from Updates

        The following example shows how to configure the device to discard path attributes 100 and 128 from incoming Update messages from the specified neighbor. The rest of the Update message will be processed as usual.

         router bgp 65600
          neighbor 2001:DB8:1::1 path-attribute discard 100 in
          neighbor 2001:DB8:1::1 path-attribute discard 128 in 
              

        The following example shows how to configure the device to discard path attributes in the range from 17 to 255 from incoming Update messages from the specified neighbor. The rest of the Update message will be processed as usual.

         router bgp 65600
          neighbor 2001:DB8:1::1 path-attribute discard 17 255 in
        

        Additional References

        Related Documents

        Related Topic

        Document Title

        Cisco IOS commands

        Cisco IOS Master Commands List, All Releases

        BGP commands

        Cisco IOS IP Routing: BGP Command Reference

        Standards and RFCs

        Standard/RFC

        Title

        draft-ietf-idr-error-handling

        Revised Error Handling for BGP Updates from External Neighbors

        Technical Assistance

        Description

        Link

        The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

        http:/​/​www.cisco.com/​cisco/​web/​support/​index.html

        Feature Information for BGP Attribute Filter and Enhanced Attribute Error Handling

        The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

        Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.
        Table 1 Feature Information for BGP Attribute Filter and Enhanced Attribute Error Handling

        Feature Name

        Releases

        Feature Information

        BGP Attribute Filter and Enhanced Attribute Error Handling

        15.2(4)S

        The BGP Attribute Filter allows you to “treat-as-withdraw” updates that contain specific path attributes. The prefixes contained in the update are removed from the routing table. The feature also allows you to remove specific path attributes from incoming updates. Both behaviors provide an increased measure of security. The BGP Enhanced Attribute Error Handling feature prevents peer sessions from flapping due to errors from any malformed update, thereby saving resources.

        The following commands were introduced: bgp enhanced-error, neighbor path-attribute discard, neighbor path-attribute treat-as-withdraw, show ip bgp path-attribute discard, and show ip bgp path-attribute unknown.

        The following commands were modified: show ip bgp, show ip bgp neighbor, and show ip bgp vpnv4 all.