Step 1 |
enable
Example:
|
Enables privileged EXEC mode.
|
Step 2 |
configure
terminal
Example:
Router# configure terminal
|
Enters global configuration mode.
|
Step 3 |
hostname
name
Example:
Router(config)# hostname cust1-53a
|
Specifies the hostname for the network server.
|
Step 4 |
aaa
new-model
Example:
Router(config)# aaa new-model
|
Enables the AAA server.
|
Step 5 |
aaa
authentication
ppp
{default |
list-name}
method1 [method2...]
Example:
Router(config)# aaa authentication ppp default if-needed group radius
|
Specifies one or more AAA authentication methods for use on serial interfaces that are running PPP.
|
Step 6 |
aaa
authorization
configuration
default
{radius
|
tacacs+
Example:
Router(config)# aaa authorization configuration default radius
|
Downloads configuration information from the AAA server.
|
Step 7 |
show
ipv6
route
[ipv6-address |
ipv6-prefix
/
prefix-length |
protocol |
interface-type
interface-number
Example:
Router(config)# show ipv6 route
|
Shows the routes installed by the previous commands.
|
Step 8 |
virtual-profile
virtual-template
number
Example:
Router(config)# virtual-profile virtual-template 1
|
Enables virtual profiles by virtual interface template.
|
Step 9 |
interface
serial
controller-number
:
timeslot
Example:
Router(config)# interface serial 0:15
|
Specifies a serial interface created on a channelized E1 or channelized T1 controller (for ISDN PRI, channel-associated signaling, or robbed-bit signaling).
This command also puts the router into interface configuration mode.
|
Step 10 |
encapsulation
encapsulation-type
Example:
Router(config-if)# encapsulation ppp
|
Sets the encapsulation method used by the interface.
|
Step 11 |
exit
Example:
|
Returns to global configuration mode.
|
Step 12 |
dialer-group
group-number
Example:
Router(config)# dialer-group 1
|
Controls access by configuring an interface to belong to a specific dialing group.
|
Step 13 |
ppp
authentication
protocol1
[protocol2...] [if-needed] [list-name |
default] [callin] [one-time] [optional]
Example:
Router(config)# ppp authentication chap
|
Enables Challenge Handshake Authentication Protocol (CHAP) or Password Authentication Protocol (PAP) or both and specifies the order in which CHAP and PAP authentication are selected on the interface.
|
Step 14 |
interface
virtual-template
number
Example:
Router(config)# interface virtual-template 1
|
Creates a virtual template interface that can be configured and applied dynamically in creating virtual access interfaces.
|
Step 15 |
ipv6
enable
Example:
Router(config)# ipv6 enable
|
Enables IPv6 processing on an interface that has not been configured with an explicit IPv6 address.
|
Step 16 |
dialer-list
dialer-group
protocol
protocol-name
{permit |
deny |
list
access-list-number |
access-group}
Example:
Router(config)# dialer-list 1 protocol ipv6 permit
|
Defines a dial-on-demand routing (DDR) dialer list for dialing by protocol or by a combination of a protocol and a previously defined access list.
|
Step 17 |
radius-server
host
{hostname |
ip-address} [test
username
user-name] [auth-port
port-number] [ignore-auth-port] [acct-port
port-number] [ignore-acct-port] [timeout
seconds] [retransmit
retries] [key
string] [alias {hostname |
ip-address}] [idle-time
seconds
Example:
Router(config)# radius-server host 172.17.250.8 auth-port 1812 acct-port 1813 key testing123
|
Specifies a RADIUS server host.
|