Cisco Remote PHY Shelf 7200 Software 1.3
Upgrading to Cisco Remote PHY Shelf 7200 Software 1.3
Downgrading from Cisco Remote PHY Shelf 7200 Software 1.3

Cisco Remote PHY Shelf 7200 Software 1.3

Upgrading to Cisco Remote PHY Shelf 7200 Software 1.3

Upgrading Cisco Remote PHY Shelf 7200 and cBR-8 Router

Before you begin

Before upgrading the system, make sure the following requirements are met:

All eRPDs are online.
Download two files from Cisco.com Software Center:
- IOS XE Software Version 17.3.1x: cbrsup-universalk9.17.03.01x.SPA.bin
- Cisco Remote PHY Shelf 7200 Software 1.3: HA-SHELF-V1-3.itb
- Cisco Remote PHY Shelf 7200 Firmware 1.3: hashelf_firmware-V1.3_20201215093439.pkg
Console access for both SUPs are required.

Note

For more information about upgrading the cBR-8 router, see https://www.cisco.com/c/en/us/td/docs/cable/cbr/upgrade/guide/b_cbr_upgrade_17_3.html.

Procedure

Step 1

Copy Cisco RPHY Shelf 7200 1.3 Firmware package to HTTP or TFTP server that RPDs can reach to.

Step 2

Telnet to FCC to upgrade FCC UBoot.


upgrade hw-programmable fcc uboot tftp <tftp_server_ip> hashelf_firmware-V1.3_20201215093439.pkg

Step 3

Reboot FCC as required in previous step output.

Step 4

After bootup, check UBoot version.


HA-Shelf-FCC#show platform diag
Chassis type: HA-RPHY-CHASSIS
 
HA-RPHY-FAN-TRAY:
                State                       : OK
                Software declared up time   : 30 minutes, 54 seconds
                Primary UBoot               : 200821 *
                Golden UBoot                : 180508
                IOFPGA version              : a209 (Primary)
                EOBC version                : 1.01

Step 5

Copy Cisco IOS XE Amsterdam 17.3.1x package to bootflash: and stby-bootflash:.


copy <location>/cbrsup-universalk9.17.03.01x.SPA.bin bootflash: 
copy <location>/cbrsup-universalk9.17.03.01x.SPA.bin stby-bootflash:

Step 6

Verify Cisco IOS XE Amsterdam 17.3.1x package against the md5 hash as provided in the Cisco.com Software center.


verify /md5 bootflash:cbrsup-universalk9.17.03.01x.SPA.bin.SPA.bin 
verify /md5 stby-bootflash:cbrsup-universalk9.17.03.01x.SPA.bin

Step 7

Backup current running config to bootflash:.


copy running-config bootflash:pre-upgrade.cfg

Step 8

Check system status prior to upgrade. Save the information to compare against the system status after upgrade. For the commands to use to check the status, see the show commands at the end of this section.

Note

Cisco recommends using HTTP server to upgrade RPHY Shelf 7200.

Step 9

Copy Cisco RPHY Shelf 7200 1.3 image package to HTTP or TFTP server that RPDs can reach to.

Step 10

Verify current RPHY Shelf 7200 software version.


show cable rpd sw-version

Step 11

Upgrade one or more RPHY Shelf image to 1.3 release from cBR-8.

To upgrade one RPHY Shelf image using HTTP server, run this command:


cable rpd group <HA-Shelf_chassis_base_mac> upgrade <http_server_ip>  http <HA_Shelf_V1.3_file_path>

To upgrade one RPHY Shelf image using TFTP server, run this command:

cable rpd group <HA-Shelf_chassis_base_mac> upgrade <tftp_server_ip>  tftp <HA_Shelf_V1.3_file_path>

To retrieve the RPHY Shelf 7200 base MAC address, run the show cable rpd group command. The Group ID column displays the base mac address for the respective HA Shelf 7200 chassis. If there is a primary RPD in the RPD group, which means the M column in the command output displays Y as shown below, you can upgrade the image of the RPD group.

Router#show cable rpd group
Load for five secs: 4%/1%; one minute: 6%; five minutes: 6%
No time source, *09:05:11.393 CST Mon Jun 3 2019
Codes: M-Master
MAC Address    IP Address     I/F     State  Group Id       Slot  M Name 
a0f8.496f.f566 120.102.22.198 Te6/1/2 online 0027.900a.4c1a 1     N rphy61 
a0f8.496f.f5f0 120.102.22.199 Te6/1/2 online 0027.900a.4c1a 2     Y rphy62 
7abd.44a1.0083 120.102.22.194 Te7/1/7 online 7abd.44a1.0000 3     N erpd33 
7abd.44a1.0082 120.102.22.193 Te7/1/7 online 7abd.44a1.0000 3     N erpd32 
7abd.44a1.0085 120.102.22.196 Te7/1/7 online 7abd.44a1.0000 3     Y erpd35 
7abd.44a1.0084 120.102.22.195 Te7/1/7 online 7abd.44a1.0000 3     N erpd34 
7abd.44a1.0081 120.102.22.192 Te7/1/7 online 7abd.44a1.0000 3     N erpd31 
badb.ad17.0c20 120.102.22.102 Te6/1/7 online badb.ad17.0c00 0     N f02-00 
badb.ad17.0c21 120.102.22.101 Te6/1/7 online badb.ad17.0c00 0     N f02-01 
badb.ad17.0c24 120.102.22.106 Te6/1/7 online badb.ad17.0c00 0     N f02-04 
badb.ad17.0c22 120.102.22.104 Te6/1/7 online badb.ad17.0c00 0     N f02-02 
badb.ad17.0c23 120.102.22.105 Te6/1/7 online badb.ad17.0c00 0     Y f02-03 
badb.ad17.0c25 120.102.22.109 Te6/1/7 online badb.ad17.0c00 0     N f02-05

To upgrade all RPHY Shelf images using HTTP server, run this command

 cable rpd group all upgrade <http_server_ip>  http <HA_Shelf_V1.3_file_path>

To upgrade all RPHY Shelf images using TFTP server, run this command

cable rpd group all upgrade <tftp_server_ip>  tftp <HA_Shelf_V1.3_file_path>

Step 12

Verify one or more RPHY Shelf 7200 chassis status.

To verify one RPHY Shelf 7200 chassis status, run this command.

cable rpd group <chassis base mac> upgrade status

To verify all RPHY Shelf 7200 chassis status, run this command.

 cable rpd group all upgrade status

Step 13

Configure the chassis to boot the system with Cisco IOS XE Amsterdam 17.3.1x image and save running-configuration.


Configure terminal
no boot system
boot system bootflash:cbrsup-universalk9.17.03.01x.SPA.bin
config-register 0x2102
end
copy running-config startup-config

Step 14

Reload and bring up the cBR-8 router.

Reload

Step 15

Adjust RPHY Shelf 7200 max-carrier and type, re-apply rpd-ds base-power for each RPHY Shelf 7200, save and backup current running-config.


cBR8(config)#cable rpd shelf-1-1
cBR8(config-rpd)#rpd-ds 0 base-power ?
  <20-22>  Base Channel Power Value in dBmV
 
cBR8(config-rpd)#type shelf
cBR8(config-rpd)#rpd-ds 0 max-carrier 16
cBR8(config-rpd)#rpd-ds 0 base-power ?
  <37-46>  Base Channel Power Value in dBmV
 
cBR8(config-rpd)#rpd-ds 0 base-power x //depends on customer real env
cBR8(config-rpd)#end
cBR8#copy running-config startup-config
cBR8#copy running-config bootflash:post-upgrade.cfg

Step 16

To check if all RPHY Shelf 7200 chassis have been upgraded to new version 1.3 and come online succesfully you can either:

Telnet to FCC IP and run the show version command or

To check if one or more RPHY Shelf 7200 chassis have been upgraded, SSH to the eRPD and run the show version command.

What to do next

These show commands may be useful in the verification test:

select erpd slot slot_id index index_id — RPHY Shelf 7200 command, normally run on FCC, but can also run on primary eRPD and line cards.
select linecard slot slot_id — RPHY Shelf 7200 command, normally run on FCC, but can also run on primary eRPD and line cards.
show version— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show platform— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show platform diag— Supported on cBR-8 and RPHY Shelf 7200
show environment— Supported on cBR-8
show environment all | alarms— Supported on RPHY Shelf 7200
show environment power— Supported on cBR-8
show platform hardware slot P <0-5> mcu status— Supported on cBR-8
show facility-alarm status — Supported on cBR-8
show redundancy— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show redundancy line card all— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show ip ospf neighbor— Supported on cBR-8
show cable modem voice— Supported on cBR-8
show cable calls— Supported on cBR-8
show cable licenses all— Supported on cBR-8
show inventory— Supported on cBR-8
show log — Supported on cBR-8 and RPHY Shelf 7200 with different outputs
show cable rpd— Supported on cBR-8
show cable modem summary total— Supported on cBR-8
show cable rpd lcha— Supported on cBR-8
show running— Supported on cBR-8 and RPHY Shelf 7200 with different outputs
show tech— Supported on cBR-8 and RPHY Shelf 7200 with different outputs

Upgrading Cisco Remote PHY Shelf 7200 Only

Before you begin

Before upgrading the system, make sure the following requirements are met:

All eRPDs are in init(gcp), init(clock), or online state.
Download new image file from Cisco.com Software Center:
- Cisco Remote PHY Shelf 7200 Software 1.3: HA-SHELF-V1-3.itb
- Cisco Remote PHY Shelf 7200 Firmware 1.3: hashelf_firmware-V1.3_20201215093439.pkg

Note

For more information about upgrading the cBR-8 router, see https://www.cisco.com/c/en/us/td/docs/cable/cbr/upgrade/guide/b_cbr_upgrade_17_3.html.

Note

Cisco recommends that to upgrade only Cisco Remote PHY Shelf 7200, you must run all commands on the Cisco Remote PHY Shelf 7200.

Procedure

Step 1

Copy Cisco RPHY Shelf 7200 1.3 Firmware package to HTTP or TFTP server that RPDs can reach to.

Step 2

Telnet to FCC to upgrade FCC UBoot.


upgrade hw-programmable fcc uboot tftp <tftp_server_ip> hashelf_firmware-V1.3_20201215093439.pkg

Step 3

Reboot FCC as required in previous step output.

Step 4

After bootup, check UBoot version.


HA-Shelf-FCC#show platform diag
Chassis type: HA-RPHY-CHASSIS
 
HA-RPHY-FAN-TRAY:
                State                       : OK
                Software declared up time   : 30 minutes, 54 seconds
                Primary UBoot               : 200821 *
                Golden UBoot                : 180508
                IOFPGA version              : a209 (Primary)
                EOBC version                : 1.01

Step 5

Copy the Cisco RPHY Shelf 7200 V1.3 image package to HTTP or TFTP server that RPDs can reach to.

Note

Cisco recommends using HTTP server to upgrade RPHY Shelf 7200.

Step 6

Verify current RPHY Shelf 7200 software version.


show cable rpd sw-version

Step 7

Upgrade one or more RPHY Shelf image to 1.3 release from cBR-8.

To upgrade one RPHY Shelf image using HTTP server, run this command:


cable rpd group <HA-Shelf_chassis_base_mac> upgrade <http_server_ip>  http <HA_Shelf_V1.3_file_path>

To upgrade one RPHY Shelf image using TFTP server, run this command:

cable rpd group <HA-Shelf_chassis_base_mac> upgrade <tftp_server_ip>  tftp <HA_Shelf_V1.3_file_path>

Router#show cable rpd group
Load for five secs: 4%/1%; one minute: 6%; five minutes: 6%
No time source, *09:05:11.393 CST Mon Jun 3 2019
Codes: M-Master
MAC Address    IP Address     I/F     State  Group Id       Slot  M Name 
a0f8.496f.f566 120.102.22.198 Te6/1/2 online 0027.900a.4c1a 1     N rphy61 
a0f8.496f.f5f0 120.102.22.199 Te6/1/2 online 0027.900a.4c1a 2     Y rphy62 
7abd.44a1.0083 120.102.22.194 Te7/1/7 online 7abd.44a1.0000 3     N erpd33 
7abd.44a1.0082 120.102.22.193 Te7/1/7 online 7abd.44a1.0000 3     N erpd32 
7abd.44a1.0085 120.102.22.196 Te7/1/7 online 7abd.44a1.0000 3     Y erpd35 
7abd.44a1.0084 120.102.22.195 Te7/1/7 online 7abd.44a1.0000 3     N erpd34 
7abd.44a1.0081 120.102.22.192 Te7/1/7 online 7abd.44a1.0000 3     N erpd31 
badb.ad17.0c20 120.102.22.102 Te6/1/7 online badb.ad17.0c00 0     N f02-00 
badb.ad17.0c21 120.102.22.101 Te6/1/7 online badb.ad17.0c00 0     N f02-01 
badb.ad17.0c24 120.102.22.106 Te6/1/7 online badb.ad17.0c00 0     N f02-04 
badb.ad17.0c22 120.102.22.104 Te6/1/7 online badb.ad17.0c00 0     N f02-02 
badb.ad17.0c23 120.102.22.105 Te6/1/7 online badb.ad17.0c00 0     Y f02-03 
badb.ad17.0c25 120.102.22.109 Te6/1/7 online badb.ad17.0c00 0     N f02-05

To upgrade all RPHY Shelf images using HTTP server, run this command

 cable rpd group all upgrade <http_server_ip>  http <HA_Shelf_V1.3_file_path>

To upgrade all RPHY Shelf images using TFTP server, run this command

cable rpd group all upgrade <tftp_server_ip>  tftp <HA_Shelf_V1.3_file_path>

Step 8

Verify one or more RPHY Shelf 7200 chassis status.

To verify one RPHY Shelf 7200 chassis status, run this command.

cable rpd group <chassis base mac> upgrade status

To verify all RPHY Shelf 7200 chassis status, run this command.

 cable rpd group all upgrade status

Step 9

To check if all RPHY Shelf 7200 chassis have been upgraded to new version 1.3 and come online succesfully you can either:

Telnet to FCC IP and run the show version command or

To check if one or more RPHY Shelf 7200 chassis have been upgraded, SSH to the eRPD and run the show version command.

What to do next

These show commands may be useful in the verification test:

select erpd slot slot_id index index_id — RPHY Shelf 7200 command, normally run on FCC, but can also run on primary eRPD and line cards.
select linecard slot slot_id— RPHY Shelf 7200 command, normally run on FCC, but can also run on primary eRPD and line cards.
show version— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show platform— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show platform diag— Supported on cBR-8 and RPHY Shelf 7200
show environment— Supported on cBR-8
show environment all | alarms— Supported on RPHY Shelf 7200
show environment power— Supported on cBR-8
show platform hardware slot P <0-5> mcu status— Supported on cBR-8
show facility-alarm status — Supported on cBR-8
show redundancy— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show redundancy line card all— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show ip ospf neighbor— Supported on cBR-8
show cable modem voice— Supported on cBR-8
show cable calls— Supported on cBR-8
show cable licenses all— Supported on cBR-8
show inventory— Supported on cBR-8
show log — Supported on cBR-8 and RPHY Shelf 7200 with different outputs
show cable rpd— Supported on cBR-8
show cable modem summary total— Supported on cBR-8
show cable rpd lcha— Supported on cBR-8
show running— Supported on cBR-8 and RPHY Shelf 7200 with different outputs
show tech— Supported on cBR-8 and RPHY Shelf 7200 with different outputs

Upgrading cBR-8 Router Only

Before you begin

Before upgrading the system, make sure the following requirements are met:

All eRPDs are in init(gcp) state.
Download new image file from Cisco.com Software Center:
- IOS XE Software Version 17.3.1x: cbrsup-universalk9.17.03.01x.SPA.bin
Console access for both SUPs are required.

Note

For more information about upgrading the cBR-8 router, see https://www.cisco.com/c/en/us/td/docs/cable/cbr/upgrade/guide/b_cbr_upgrade_17_3.html.

Procedure

Step 1	Copy Cisco IOS XE Amsterdam 17.3.1x package to bootflash: and stby-bootflash:. `copy <location>/cbrsup-universalk9.17.03.01x.SPA.bin bootflash: copy <location>/cbrsup-universalk9.17.03.01x.SPA.bin stby-bootflash:`
Step 2	Verify Cisco IOS XE Amsterdam 17.3.1x package against the md5 hash as provided in the Cisco.com Software center. `verify /md5 bootflash:cbrsup-universalk9.17.03.01x.SPA.bin verify /md5 stby-bootflash:cbrsup-universalk9.17.03.01x.SPA.bin`
Step 3	Backup current running config to bootflash:. `copy running-config bootflash:pre-upgrade.cfg`
Step 4	Check system status prior to upgrade. Save the information to compare against the system status after upgrade. For the commands to use to check the status, see the show commands at the end of this section.
Step 5	Configure the chassis to boot the system with Cisco IOS XE Amsterdam 17.3.1x image and save running-configuration. `Configure terminal no boot system boot system bootflash:cbrsup-universalk9.17.03.01x.SPA.bin config-register 0x2102 end copy running-config startup-config`
Step 6	Reload and bring up the cBR-8 router. `Reload`
Step 7	Adjust RPD max-carrier and type, re-apply rpd-ds base-power for each RPD, save and backup current running-config. `cBR8(config)#cable rpd shelf-1-1 cBR8(config-rpd)#rpd-ds 0 base-power ? <20-22> Base Channel Power Value in dBmV cBR8(config-rpd)#type shelf cBR8(config-rpd)#rpd-ds 0 max-carrier 16 cBR8(config-rpd)#rpd-ds 0 base-power ? <37-46> Base Channel Power Value in dBmV cBR8(config-rpd)#rpd-ds 0 base-power x //depends on customer real env cBR8(config-rpd)#end cBR8#copy running-config startup-config cBR8#copy running-config bootflash:post-upgrade.cfg`
Step 8	To check if all RPHY Shelf 7200 chassis are upgraded and come online succesfully you can either: Telnet to FCC IP and run the show version command or To check if one or more RPHY Shelf 7200 chassis have been upgraded, SSH to the eRPD and run the show version command.

What to do next

These show commands may be useful in the verification test:

select erpd slot slot_id index index_id — RPHY Shelf 7200 command, normally run on FCC, but can also run on primary eRPD and line cards.
select linecard slot slot_id— RPHY Shelf 7200 command, normally run on FCC, but can also run on primary eRPD and line cards.
show version— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show platform— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show platform diag— Supported on cBR-8 and RPHY Shelf 7200
show environment— Supported on cBR-8
show environment all | alarms— Supported on RPHY Shelf 7200
show environment power— Supported on cBR-8
show platform hardware slot P <0-5> mcu status— Supported on cBR-8
show facility-alarm status — Supported on cBR-8
show redundancy— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show redundancy line card all— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show ip ospf neighbor— Supported on cBR-8
show cable modem voice— Supported on cBR-8
show cable calls— Supported on cBR-8
show cable licenses all— Supported on cBR-8
show inventory— Supported on cBR-8
show log — Supported on cBR-8 and RPHY Shelf 7200 with different outputs
show cable rpd— Supported on cBR-8
show cable modem summary total— Supported on cBR-8
show cable rpd lcha— Supported on cBR-8
show running— Supported on cBR-8 and RPHY Shelf 7200 with different outputs
show tech— Supported on cBR-8 and RPHY Shelf 7200 with different outputs

Downgrading from Cisco Remote PHY Shelf 7200 Software 1.3

Downgrading Cisco Remote PHY Shelf 7200 and cBR-8 Router

Before you begin

Before downgrading the system, make sure the following requirements are met:

All eRPDs are online.
Download two files from the following Cisco.com Software Center URL:
- IOS XE Software: https://software.cisco.com/download/home/286283913/type
  - IOS XE Software Version 16.10.1f: cbrsup-universalk9.16.10.01f.SPA.bin
  - IOS XE Software Version 16.10.1c: cbrsup-universalk9.16.10.01c.SPA.bin
- Cisco Remote PHY Shelf 7200 software: https://software.cisco.com/download/home/286321242/type
  - Cisco Remote PHY Shelf 7200 Software 1.2: HA-SHELF-V1-2.itb
  - Cisco Remote PHY Shelf 7200 Software 1.1: HA-SHELF-V1-1.itb
Console access for both SUPs are required.

Note

For more information about upgrading the cBR-8 router, see https://www.cisco.com/c/en/us/td/docs/cable/cbr/upgrade/guide/b_cbr_upgrade_17_3.html.

Procedure

Step 1	Copy Cisco IOS XE software package to bootflash: and stby-bootflash:. `copy <location>/<ios_xe_software_file> bootflash: copy <location>/<ios_xe_software_file> stby-bootflash:`
Step 2	Verify Cisco IOS XE software package against the md5 hash as provided in the Cisco.com Software center. `verify /md5 bootflash:<ios_xe_software_file> verify /md5 stby-bootflash:<ios_xe_software_file>`
Step 3	Backup the current running config to bootflash:. `copy running-config bootflash:pre-upgrade.cfg`
Step 4	Check system status prior to downgrade. Save the information to compare against the system status after downgrade. For the commands to use to check the status, see the show commands at the end of this section.
Step 5	Copy the Cisco RPHY Shelf 7200 software image package to HTTP or TFTP server that RPHY Shelf 7200 can reach to.
Step 6	Verify current RPHY Shelf 7200 software version. `show cable rpd sw-version`
Step 7	Downgrade one or more RPHY Shelf images from cBR-8. To downgrade one RPHY Shelf image using HTTP server, run this command: `cable rpd group <HA-Shelf_chassis_base_mac> upgrade <http_server_ip> http <HA_Shelf_file_path>` To downgrade one RPHY Shelf image using TFTP server, run this command: `cable rpd group <HA-Shelf_chassis_base_mac> upgrade <tftp_server_ip> tftp <HA_Shelf_file_path>` To retrieve the RPHY Shelf 7200 base mac address, run the show cable rpd group command. The Group ID column displays the base mac address for the respective HA Shelf 7200 chassis. If there is a primary RPD in the RPD group, which means the M column in the command output displays Y as shown below, you can upgrade the image of the RPD group. Router#show cable rpd group Load for five secs: 4%/1%; one minute: 6%; five minutes: 6% No time source, *09:05:11.393 CST Mon Jun 3 2019 Codes: M-Master MAC Address IP Address I/F State Group Id Slot M Name a0f8.496f.f566 120.102.22.198 Te6/1/2 online 0027.900a.4c1a 1 N rphy61 a0f8.496f.f5f0 120.102.22.199 Te6/1/2 online 0027.900a.4c1a 2 Y rphy62 7abd.44a1.0083 120.102.22.194 Te7/1/7 online 7abd.44a1.0000 3 N erpd33 7abd.44a1.0082 120.102.22.193 Te7/1/7 online 7abd.44a1.0000 3 N erpd32 7abd.44a1.0085 120.102.22.196 Te7/1/7 online 7abd.44a1.0000 3 Y erpd35 7abd.44a1.0084 120.102.22.195 Te7/1/7 online 7abd.44a1.0000 3 N erpd34 7abd.44a1.0081 120.102.22.192 Te7/1/7 online 7abd.44a1.0000 3 N erpd31 badb.ad17.0c20 120.102.22.102 Te6/1/7 online badb.ad17.0c00 0 N f02-00 badb.ad17.0c21 120.102.22.101 Te6/1/7 online badb.ad17.0c00 0 N f02-01 badb.ad17.0c24 120.102.22.106 Te6/1/7 online badb.ad17.0c00 0 N f02-04 badb.ad17.0c22 120.102.22.104 Te6/1/7 online badb.ad17.0c00 0 N f02-02 badb.ad17.0c23 120.102.22.105 Te6/1/7 online badb.ad17.0c00 0 Y f02-03 badb.ad17.0c25 120.102.22.109 Te6/1/7 online badb.ad17.0c00 0 N f02-05 To downgrade all RPHY Shelf images using HTTP server, run this command `cable rpd group all upgrade <http_server_ip> http <HA_Shelf_file_path>` To downgrade all RPHY Shelf images using TFTP server, run this command `cable rpd group all upgrade <tftp_server_ip> tftp <HA_Shelf_file_path>`
Step 8	Verify one or more RPHY Shelf 7200 chassis status. To verify one RPHY Shelf 7200 chassis status, run this command. `cable rpd group <chassis base mac> upgrade status` To verify all RPHY Shelf 7200 chassis status, run this command. `cable rpd group all upgrade status`
Step 9	Configure the chassis to boot the system with target Cisco IOS XE image and save running-configuration. `Configure terminal no boot system boot system bootflash:<ios_xe_software_file> config-register 0x2102 end copy running-config startup-config`
Step 10	Reload and bring up the cBR-8 router. `Reload`
Step 11	To check if all RPHY Shelf 7200 chassis have been downgraded to the target version and come online succesfully, you can either: Telnet to FCC IP and run the show version command or To check if one or more RPHY Shelf 7200 chassis have been downgraded, SSH to the eRPD and run the show version command.

What to do next

These show commands may be useful in the verification test:

select erpd slot slot_id index index_id — RPHY Shelf 7200 command, normally run on FCC, but can also run on primary eRPD and line cards.
select linecard slot slot_id— RPHY Shelf 7200 command, normally run on FCC, but can also run on primary eRPD and line cards.
show version— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show platform— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show platform diag— Supported on cBR-8 and RPHY Shelf 7200
show environment— Supported on cBR-8
show environment all | alarms— Supported on RPHY Shelf 7200
show environment power— Supported on cBR-8
show platform hardware slot P <0-5> mcu status— Supported on cBR-8
show facility-alarm status — Supported on cBR-8
show redundancy— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show redundancy line card all— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show ip ospf neighbor— Supported on cBR-8
show cable modem voice— Supported on cBR-8
show cable calls— Supported on cBR-8
show cable licenses all— Supported on cBR-8
show inventory— Supported on cBR-8
show log — Supported on cBR-8 and RPHY Shelf 7200 with different outputs
show cable rpd— Supported on cBR-8
show cable modem summary total— Supported on cBR-8
show cable rpd lcha— Supported on cBR-8
show running— Supported on cBR-8 and RPHY Shelf 7200 with different outputs
show tech— Supported on cBR-8 and RPHY Shelf 7200 with different outputs

Downgrading Cisco Remote PHY Shelf 7200 Only

Before you begin

Before downgrading the system, make sure the following requirements are met:

All eRPDs are in init(gcp) state.
Download new image file from the following Cisco.com Software Center URL:

https://software.cisco.com/download/home/286321242/type
- Cisco Remote PHY Shelf 7200 Software 1.2: HA-SHELF-V1-2.itb
- Cisco Remote PHY Shelf 7200 Software 1.1: HA-SHELF-V1-1.itb

Note

For more information about upgrading the cBR-8 router, see https://www.cisco.com/c/en/us/td/docs/cable/cbr/upgrade/guide/b_cbr_upgrade_17_3.html.

Procedure

Step 1

Copy the target Cisco RPHY Shelf 7200 software image package to HTTP or TFTP server that RPHY Shelf 7200 can reach to.

Note

Cisco recommends using HTTP server to upgrade RPHY Shelf 7200.

Step 2

Verify current RPHY Shelf 7200 software version.


show cable rpd sw-version

Step 3

Downgrade one or more RPHY Shelf image from cBR-8.

To downgrade one RPHY Shelf image using HTTP server, run this command:


cable rpd group <HA-Shelf_chassis_base_mac> upgrade <http_server_ip>  http <HA_Shelf_file_path>

To downgrade one RPHY Shelf image using TFTP server, run this command:

cable rpd group <HA-Shelf_chassis_base_mac> upgrade <tftp_server_ip>  tftp <HA_Shelf_file_path>

To retrieve the RPHY Shelf 7200 base mac address, run the show cable rpd group command. The Group ID column displays the base mac address for the respective HA Shelf 7200 chassis. If there is a primary RPD in the RPD group, which means the M column in the command output displays Y as shown below, you can upgrade the image of the RPD group.

Router#show cable rpd group
Load for five secs: 4%/1%; one minute: 6%; five minutes: 6%
No time source, *09:05:11.393 CST Mon Jun 3 2019
Codes: M-Master
MAC Address    IP Address     I/F     State  Group Id       Slot  M Name 
a0f8.496f.f566 120.102.22.198 Te6/1/2 online 0027.900a.4c1a 1     N rphy61 
a0f8.496f.f5f0 120.102.22.199 Te6/1/2 online 0027.900a.4c1a 2     Y rphy62 
7abd.44a1.0083 120.102.22.194 Te7/1/7 online 7abd.44a1.0000 3     N erpd33 
7abd.44a1.0082 120.102.22.193 Te7/1/7 online 7abd.44a1.0000 3     N erpd32 
7abd.44a1.0085 120.102.22.196 Te7/1/7 online 7abd.44a1.0000 3     Y erpd35 
7abd.44a1.0084 120.102.22.195 Te7/1/7 online 7abd.44a1.0000 3     N erpd34 
7abd.44a1.0081 120.102.22.192 Te7/1/7 online 7abd.44a1.0000 3     N erpd31 
badb.ad17.0c20 120.102.22.102 Te6/1/7 online badb.ad17.0c00 0     N f02-00 
badb.ad17.0c21 120.102.22.101 Te6/1/7 online badb.ad17.0c00 0     N f02-01 
badb.ad17.0c24 120.102.22.106 Te6/1/7 online badb.ad17.0c00 0     N f02-04 
badb.ad17.0c22 120.102.22.104 Te6/1/7 online badb.ad17.0c00 0     N f02-02 
badb.ad17.0c23 120.102.22.105 Te6/1/7 online badb.ad17.0c00 0     Y f02-03 
badb.ad17.0c25 120.102.22.109 Te6/1/7 online badb.ad17.0c00 0     N f02-05

To downgrade all RPHY Shelf images using HTTP server, run this command

 cable rpd group all upgrade <http_server_ip>  http <HA_Shelf_file_path>

To downgrade all RPHY Shelf images using TFTP server, run this command

cable rpd group all upgrade <tftp_server_ip>  tftp <HA_Shelf_file_path>

Step 4

Verify one or more RPHY Shelf 7200 chassis status.

To verify one RPHY Shelf 7200 chassis status, run this command.

cable rpd group <chassis base mac> upgrade status

To verify all RPHY Shelf 7200 chassis status, run this command.

 cable rpd group all upgrade status

Step 5

To check if all RPHY Shelf 7200 chassis have been downgraded to target version and come online succesfully, you can either:

Telnet to FCC IP and run the show version command or

To check if one or more RPHY Shelf 7200 chassis have been upgraded, SSH to the eRPD and run the show version command.

What to do next

These show commands may be useful in the verification test:

select erpd slot slot_id index index_id — RPHY Shelf 7200 command, normally run on FCC, but can also run on primary eRPD and line cards.
select linecard slot slot_id— RPHY Shelf 7200 command, normally run on FCC, but can also run on primary eRPD and line cards.
show version— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show platform— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show platform diag— Supported on cBR-8 and RPHY Shelf 7200
show environment— Supported on cBR-8
show environment all | alarms— Supported on RPHY Shelf 7200
show environment power— Supported on cBR-8
show platform hardware slot P <0-5> mcu status— Supported on cBR-8
show facility-alarm status — Supported on cBR-8
show redundancy— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show redundancy line card all— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show ip ospf neighbor— Supported on cBR-8
show cable modem voice— Supported on cBR-8
show cable calls— Supported on cBR-8
show cable licenses all— Supported on cBR-8
show inventory— Supported on cBR-8
show log — Supported on cBR-8 and RPHY Shelf 7200 with different outputs
show cable rpd— Supported on cBR-8
show cable modem summary total— Supported on cBR-8
show cable rpd lcha— Supported on cBR-8
show running— Supported on cBR-8 and RPHY Shelf 7200 with different outputs
show tech— Supported on cBR-8 and RPHY Shelf 7200 with different outputs

Downgrading cBR-8 Router Only

Before you begin

Before downgrading the system, make sure the following requirements are met:

All eRPDs are in init(gcp) state.
Download new image file from the following Cisco.com Software Center URL:

https://software.cisco.com/download/home/286283913/type
- IOS XE Software Version 16.10.1f: cbrsup-universalk9.16.10.01f.SPA.bin
- IOS XE Software Version 16.10.1c: cbrsup-universalk9.16.10.01c.SPA.bin
Console access for both SUPs are required.

Note

For more information about upgrading the cBR-8 router, see https://www.cisco.com/c/en/us/td/docs/cable/cbr/upgrade/guide/b_cbr_upgrade_17_3.html.

Procedure

Step 1	Copy Cisco IOS XE software package to bootflash: and stby-bootflash:. `copy <location>/<ios_xe_software_file> bootflash: copy <location>/<ios_xe_software_file> stby-bootflash:`
Step 2	Verify Cisco IOS XE software package against the md5 hash as provided in the Cisco.com Software center. `verify /md5 bootflash:<ios_xe_software_file> verify /md5 stby-bootflash:<ios_xe_software_file>`
Step 3	Backup current running config to bootflash:. `copy running-config bootflash:pre-upgrade.cfg`
Step 4	Check system status prior to downgrade. Save the information to compare against the system status after upgrade. For the commands to use to check the status, see the show commands at the end of this section.
Step 5	Configure the chassis to boot the system with target Cisco IOS XE image and save running-configuration. `Configure terminal no boot system boot system bootflash:<ios_xe_software_file> config-register 0x2102 end copy running-config startup-config`
Step 6	Reload and bring up the cBR-8 router. `Reload`
Step 7	To check if all RPHY Shelf 7200 chassis are downgraded and come online succesfully, you can either: Telnet to FCC IP and run the show version command or To check if one or more RPHY Shelf 7200 chassis have been upgraded, SSH to the eRPD and run the show version command.

What to do next

These show commands may be useful in the verification test:

select erpd slot slot_id index index_id — RPHY Shelf 7200 command, normally run on FCC, but can also run on primary eRPD and line cards.
select linecard slot slot_id— RPHY Shelf 7200 command, normally run on FCC, but can also run on primary eRPD and line cards.
show version— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show platform— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show platform diag— Supported on cBR-8 and RPHY Shelf 7200
show environment— Supported on cBR-8
show environment all | alarms— Supported on RPHY Shelf 7200
show environment power— Supported on cBR-8
show platform hardware slot P <0-5> mcu status— Supported on cBR-8
show facility-alarm status — Supported on cBR-8
show redundancy— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show redundancy line card all— Supported on cBR-8 and RPHY Shelf 7200 with different outputs.
show ip ospf neighbor— Supported on cBR-8
show cable modem voice— Supported on cBR-8
show cable calls— Supported on cBR-8
show cable licenses all— Supported on cBR-8
show inventory— Supported on cBR-8
show log — Supported on cBR-8 and RPHY Shelf 7200 with different outputs
show cable rpd— Supported on cBR-8
show cable modem summary total— Supported on cBR-8
show cable rpd lcha— Supported on cBR-8
show running— Supported on cBR-8 and RPHY Shelf 7200 with different outputs
show tech— Supported on cBR-8 and RPHY Shelf 7200 with different outputs

Upgrade Guide for Cisco Remote PHY Shelf 7200 Software 1.x

Bias-Free Language

Book Title

Upgrade Guide for Cisco Remote PHY Shelf 7200 Software 1.x

Chapter Title