تكوين Dynamic Multipoint VPN باستخدام GRE عبر IPSec مع EIGRP و NAT و CBAC

3620-B#write terminal
Building configuration...

Current configuration : 2607 bytes
!
version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname 3620-B
!
logging queue-limit 100
!
memory-size iomem 10
ip subnet-zero
!
!
ip cef
no ip domain lookup
!

!--- This is the CBAC configuration and what to inspect. !--- This will be applied outbound on the external interface.

ip inspect name in2out rcmd
ip inspect name in2out ftp
ip inspect name in2out tftp
ip inspect name in2out tcp timeout 43200
ip inspect name in2out http
ip inspect name in2out udp
ip audit po max-events 100
!
!
!

!--- Create an Internet Security Association and Key Management !--- Protocol (ISAKMP) policy for Phase 1 negotiations.

!
crypto isakmp policy 5
 authentication pre-share
 group 2

!--- Add dynamic pre-shared key.


!--- Here "dmvpn" is the word that is used as the key.

crypto isakmp key dmvpnkey address 0.0.0.0 0.0.0.0
crypto isakmp nat keepalive 20
!
!

!--- Create the Phase 2 policy for actual data encryption.

crypto ipsec transform-set dmvpnset esp-3des esp-sha-hmac
!

!--- Create an IPSec profile to be applied dynamically !--- to the GRE over IPSec tunnels.

crypto ipsec profile dmvpnprof
 set transform-set dmvpnset
!
!
no voice hpi capture buffer
no voice hpi capture destination
!
!
mta receive maximum-recipients 0
!
!

!--- This is the inside interface.

interface Loopback1
 ip address 192.168.117.1 255.255.255.0
 ip nat inside
!

!--- This is the mGRE interface for dynamic GRE tunnels.

interface Tunnel1
 description MULTI-POINT GRE TUNNEL for BRANCHES
 bandwidth 1000
 ip address 172.16.0.1 255.255.255.0
 no ip redirects
 ip mtu 1400
 ip nhrp authentication dmvpn
 ip nhrp map multicast dynamic
 ip nhrp network-id 99
 ip nhrp holdtime 300
 no ip split-horizon eigrp 1
 no ip mroute-cache
 delay 1000
 tunnel source FastEthernet0/0
 tunnel mode gre multipoint
 tunnel key 100000
 tunnel protection ipsec profile dmvpnprof
!

!--- This is the outside interface.

interface FastEthernet0/0
 ip address 14.24.117.1 255.255.0.0
 ip nat outside
 ip access-group 100 in
 ip inspect in2out out
 no ip mroute-cache
 duplex auto
 speed auto
!
interface Serial0/0
 no ip address
 shutdown
 clockrate 2000000
 no fair-queue
!
interface FastEthernet0/1
 no ip address
 no ip mroute-cache
 duplex auto
 speed auto
!

!--- Enable a routing protocol to send/receive dynamic !--- updates about the private networks over the tunnels.

router eigrp 1
 network 172.16.0.0 0.0.0.255
 network 192.168.117.0
 no auto-summary
!

!--- Perform NAT on local traffic !--- going directly out FastEthernet0/0.

ip nat inside source list 110 interface FastEthernet0/0 overload
ip http server
no ip http secure-server
ip classless
ip route 0.0.0.0 0.0.0.0 14.24.1.1
ip route 2.0.0.0 255.0.0.0 14.24.121.1
!
!
!

!--- Allow ISAKMP, ESP, and GRE traffic inbound. !--- CBAC will open other inbound access as needed.

access-list 100 permit udp any host 14.24.117.1 eq 500
access-list 100 permit esp any host 14.24.117.1
access-list 100 permit gre any host 14.24.117.1  
access-list 100 deny ip any any 
access-list 110 permit ip 192.168.117.0 0.0.0.255 any
!
!
call rsvp-sync
!
!
mgcp profile default
!
dial-peer cor custom
!
!
line con 0
 exec-timeout 0 0
line aux 0
line vty 0 4
 login
!
!
end

3620-B#

3620-A#write terminal
Building configuration...

Current configuration : 2559 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname 3620-A
!
boot system flash slot0:c3620-ik9o3s7-mz.122-15.T1.bin
logging queue-limit 100
!
memory-size iomem 15
ip subnet-zero
!
!
ip cef
no ip domain lookup
!

!--- This is the CBAC configuration and what to inspect. !--- This will be applied outbound on the external interface.

ip inspect name in2out rcmd
ip inspect name in2out tftp
ip inspect name in2out udp
ip inspect name in2out tcp timeout 43200
ip inspect name in2out realaudio
ip inspect name in2out vdolive
ip inspect name in2out netshow
ip audit po max-events 100
!
!
!

!--- Create an ISAKMP policy for !--- Phase 1 negotiations.

crypto isakmp policy 5
 authentication pre-share
 group 2

!--- Add dynamic pre-shared key.

crypto isakmp key dmvpnkey address 0.0.0.0 0.0.0.0
!
!

!--- Create the Phase 2 policy for actual data encryption.

crypto ipsec transform-set dmvpnset esp-3des esp-sha-hmac
!

!--- Create an IPSec profile to be applied dynamically !--- to the GRE over IPSec tunnels.

crypto ipsec profile dmvpnprof
 set transform-set dmvpnset
!
!
no voice hpi capture buffer
no voice hpi capture destination
!
!
mta receive maximum-recipients 0
!
!

!--- This is the inside interface.

interface Loopback1
 ip address 192.168.118.1 255.255.255.0
 ip nat inside
!

!--- This is the mGRE interface for dynamic GRE tunnels.

interface Tunnel1
 description HOST DYNAMIC TUNNEL
 bandwidth 1000
 ip address 172.16.0.2 255.255.255.0
 no ip redirects
 ip mtu 1400
 ip nhrp authentication dmvpn
 ip nhrp map 172.16.0.1 14.24.117.1
 ip nhrp map multicast 14.24.117.1
 ip nhrp network-id 99
 ip nhrp holdtime 300
 ip nhrp nhs 172.16.0.1
 no ip mroute-cache
 delay 1000
 tunnel source Ethernet0/0
 tunnel mode gre multipoint
 tunnel key 100000
 tunnel protection ipsec profile dmvpnprof
!

!--- This is the outside interface.

interface Ethernet0/0
 ip address 14.24.118.1 255.255.0.0
 ip nat outside
 ip inspect in2out out
 ip access-group 100 in
 no ip mroute-cache
 half-duplex
!
interface Ethernet0/1
 no ip address
 half-duplex
!
interface Ethernet0/2
 no ip address
 shutdown
 half-duplex
!
interface Ethernet0/3
 no ip address
 shutdown
 half-duplex
!

!--- Enable a routing protocol to send/receive dynamic !--- updates about the private networks over the tunnel.

router eigrp 1
 network 172.16.0.0 0.0.0.255
 network 192.168.118.0
 no auto-summary
!

!--- Perform NAT on local traffic !--- going directly out Ethernet0/0.

ip nat inside source list 110 interface Ethernet0/0 overload
ip http server
no ip http secure-server
ip classless
ip route 0.0.0.0 0.0.0.0 14.24.1.1
!
!

!--- Allow ISAKMP, ESP, and GRE traffic inbound. !--- CBAC will open inbound access as needed.

access-list 100 permit udp any host 14.24.118.1 eq 500
access-list 100 permit esp any host 14.24.118.1
access-list 100 permit gre any host 14.24.118.1  
access-list 100 deny ip any any
access-list 110 permit ip 192.168.118.0 0.0.0.255 any
!
!
call rsvp-sync
!
!
mgcp profile default
!
dial-peer cor custom
!
!
line con 0
 exec-timeout 0 0
line aux 0
line vty 0 4
 login
!
!
end

3620-A#

1720-b#write terminal
Building configuration...

Current configuration : 2543 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname 1720-b
!
boot system flash flash:c1700-ny-mz.122-8.YJ
logging queue-limit 100
enable password cisco
!
username 7206-B password 0 cisco
ip subnet-zero
!
!
no ip domain lookup
!
ip cef

!--- This is the CBAC configuration and what to inspect. !--- This will be applied outbound on the external interface.

ip inspect name in2out rcmd
ip inspect name in2out tftp
ip inspect name in2out udp
ip inspect name in2out tcp timeout 43200
ip inspect name in2out realaudio
ip inspect name in2out vdolive
ip inspect name in2out netshow
ip audit po max-events 100
!
!
vpdn-group 1
 request-dialin
  protocol pppoe
!
!

!--- Create an ISAKMP policy for !--- Phase 1 negotiations.

crypto isakmp policy 5
 authentication pre-share
 group 2

!--- Add dynamic pre-shared key.

crypto isakmp key dmvpnkey address 0.0.0.0 0.0.0.0
!
!

!--- Create the Phase 2 policy for actual data encryption.

crypto ipsec transform-set dmvpnset esp-3des esp-sha-hmac
!

!--- Create an IPSec profile to be applied dynamically !--- to the GRE over IPSec tunnels.

crypto ipsec profile dmvpnprof
 set transform-set dmvpnset
!
!

!--- This is the inside interface.

interface Loopback1
 ip address 192.168.116.1 255.255.255.0
 ip nat inside
!

!--- This is the mGRE interface for dynamic GRE tunnels.

interface Tunnel1
 description HOST DYNAMIC TUNNEL
 bandwidth 1000
 ip address 172.16.0.3 255.255.255.0
 no ip redirects
 ip mtu 1400
 ip nhrp authentication dmvpn
 ip nhrp map 172.16.0.1 14.24.117.1
 ip nhrp map multicast 14.24.117.1
 ip nhrp network-id 99
 ip nhrp holdtime 300
 ip nhrp nhs 172.16.0.1
 no ip mroute-cache
 delay 1000
 tunnel source Dialer1
 tunnel mode gre multipoint
 tunnel key 100000
 tunnel protection ipsec profile dmvpnprof
!
interface Ethernet0
 no ip address
 half-duplex
!
interface FastEthernet0
 no ip address
 no ip mroute-cache
 speed auto
 pppoe enable
 pppoe-client dial-pool-number 1
!

!--- This is the outside interface.

interface Dialer1
 ip address 2.2.2.10 255.255.255.0
 ip inspect in2out out
 ip access-group 100 in
 encapsulation ppp
 dialer pool 1
 dialer-group 1
 ppp authentication pap chap callin
!

!--- Enable a routing protocol to send/receive dynamic !--- updates about the private networks.

router eigrp 1
 network 172.16.0.0 0.0.0.255
 network 192.168.116.0
 no auto-summary
!

!--- Perform NAT on local traffic !--- going directly out Dialer1.

ip nat inside source list 110 interface Dialer1 overload
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer1
no ip http server
no ip http secure-server
!
!
!

!--- Allow ISAKMP, ESP, and GRE traffic inbound. !--- CBAC will open inbound access as needed.

access-list 100 permit udp any host 14.24.116.1 eq 500
access-list 100 permit esp any host 14.24.116.1
access-list 100 permit gre any host 14.24.116.1  
access-list 100 deny ip any any
access-list 110 permit ip 192.168.116.0 0.0.0.255 any
dialer-list 1 protocol ip permit
!
!
!
line con 0
 exec-timeout 0 0
line aux 0
line vty 0 4
 login
!
no scheduler allocate
end

1720-b#

1720-A#write terminal
Building configuration...

Current configuration : 1770 bytes
!
version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname 1720-A
!
logging queue-limit 100
!
memory-size iomem 25
ip subnet-zero
!
!
!
ip cef

!--- This is the CBAC configuration and what to inspect. !--- This will be applied outbound on the external interface.

ip inspect name in2out rcmd
ip inspect name in2out tftp
ip inspect name in2out udp
ip inspect name in2out tcp timeout 43200
ip inspect name in2out realaudio
ip inspect name in2out vdolive
ip inspect name in2out netshow
ip audit po max-events 100
!
!

!--- Create an ISAKMP policy for !--- Phase 1 negotiations.

crypto isakmp policy 5
 authentication pre-share
 group 2

!--- Add dynamic pre-shared key.

crypto isakmp key dmvpnkey address 0.0.0.0 0.0.0.0
!
!

!--- Create the Phase 2 policy for actual data encryption.

crypto ipsec transform-set dmvpnset esp-3des esp-sha-hmac
!

!--- Create an IPSec profile to be applied dynamically !--- to the GRE over IPSec tunnels.

crypto ipsec profile dmvpnprof
 set transform-set dmvpnset
!
!

!--- This is the inside interface.

interface Loopback1
 ip address 192.168.120.1 255.255.255.0
 ip nat inside
!

!--- This is the mGRE interface for dynamic GRE tunnels.

interface Tunnel1
 description HOST DYNAMIC TUNNEL
 bandwidth 1000
 ip address 172.16.0.4 255.255.255.0
 no ip redirects
 ip mtu 1400
 ip nhrp authentication dmvpn
 ip nhrp map 172.16.0.1 14.24.117.1
 ip nhrp map multicast 14.24.117.1
 ip nhrp network-id 99
 ip nhrp holdtime 300
 ip nhrp nhs 172.16.0.1
 no ip mroute-cache
 delay 1000
 tunnel source FastEthernet0
 tunnel mode gre multipoint
 tunnel key 100000
 tunnel protection ipsec profile dmvpnprof
!
interface Ethernet0
 no ip address
 no ip mroute-cache
 half-duplex
!

!--- This is the outside interface.

interface FastEthernet0
 ip address 14.24.120.1 255.255.0.0
 ip nat outside
 ip inspect in2out out
 ip access-group 100 in
 no ip mroute-cache
 speed auto
!

!--- Enable a routing protocol to send/receive dynamic !--- updates about the private networks.

router eigrp 1
 network 172.16.0.0 0.0.0.255
 network 192.168.120.0
 no auto-summary
!

!--- Perform NAT on local traffic !--- going directly out FastEthernet0.

ip nat inside source list 110 interface FastEthernet0 overload
ip classless
ip route 0.0.0.0 0.0.0.0 14.24.1.1
no ip http server
no ip http secure-server
!
!
!

!--- Allow ISAKMP, ESP, and GRE traffic inbound. !--- CBAC will open inbound access as needed.

access-list 100 permit udp any host 14.24.116.1 eq 500
access-list 100 permit esp any host 14.24.116.1
access-list 100 permit gre any host 14.24.116.1  
access-list 100 deny ip any any
access-list 110 permit ip 192.168.120.0 0.0.0.255 any
!
!
!
line con 0
 exec-timeout 0 0
line aux 0
line vty 0 4
 login
!
no scheduler allocate
end

1720-A#