Cisco uBR10000 Series Universal Broadband Routers

Revised May 6, 2008
May 13, 2002

NOTICE:

THIS FIELD NOTICE HAS BEEN EXPIRED AND IS NO LONGER MAINTAINED OR UPDATED BY CISCO.

THIS FIELD NOTICE IS PROVIDED ON AN "AS IS" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE, WARRANTY OR SUPPORT. USE OF THE INFORMATION ON THIS FIELD NOTICE OR MATERIALS LINKED FROM THIS FIELD NOTICE IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS FIELD NOTICE AT ANY TIME.

• More Field Notices

Products Affected

• Cisco UBR-RFSW

Problem Description

The default gateway address cannot be added to the RF switch in previous versions of the firmware. This causes difficulties in remote firmware upgrades to the RF switch across subnets.

Background

It has been discovered that remote firmware upgrades to the RF switch across subnets cannot be done because the default gateway on the switch cannot be set. Remote firmware upgrade is a very desirable feature. This capability has now been implemented in the version 2.5 of the RF switch firmware with the ability to set the default gateway.

Problem Symptoms

The RF switch will not upgrade firmware across subnets.

Workaround/Solution

To correct the problem, use the following steps:

1. Load the new images into the uBR10K with a flash disk in slot 0.

2. Set the 10K up with the following config. tftp-server disk0:rfsw250-bf-1935022d alias rfsw250-bf-1935022d tftp-server disk0:rfsw250-fl-1935030e alias rfsw250-fl-1935030e

3. Establish a console connection to the switch and type set tftp-host {ip-addr}. This is the IP address of the uBR10K for TFTP transfers.

4. Type copy tftp:rfsw250-bf-1935022d bf: to load the bootflash and copy tftp:rfsw250-fl-1935030e fl: to load the flash.

5. Perform a reload on the switch.

Caution:?You may need to reset some of the configuration after reloading such as the Switch IP address, so review your Switch config after reloading to verify.

Once upgraded to version 2.5, a default gateway address can be added to the switch and new upgrades to the switch can be done across subnets remotely. The only limit is that, if loading from Unix stations, the new image name must be lower case letters.

How To Identify Hardware Levels

rfswitch>show version

Controller firmware:
   RomMon: 1935033  V1.10
   Bootflash: 1935022  V1.20 <----------------- Bootflash Version
   Flash: 1935030C  V2.30    <----------------- Flash Version

   Slot      Model       Type     SerialNo    HwVer    SwVer
    999   193-5001    10BaseT         1069        E     2.30
      1   193-5002   upstream      1094953        F     1.30
      2   193-5002   upstream      1094943        F     1.30
      3   193-5002   upstream      1094951        F     1.30
      4   193-5002   upstream      1094954        F     1.30
      5   193-5002   upstream      1095318        F     1.30
      6   193-5002   upstream      1095245        F     1.30
      7   193-5002   upstream      1095326        F     1.30
      8   193-5002   upstream      1095243        F     1.30
      9   193-5002   upstream      1095080        F     1.30
     10   193-5002   upstream      1095322        F     1.30
     11   193-5003   dnstream      1095457        J     1.30
     12   193-5003   dnstream      1095442        J     1.30
     13   193-5003   dnstream      1095449        J     1.30
     14   not detected

For More Information

If you require further assistance, or if you have any further questions regarding this field notice, please contact the Cisco Systems Technical Assistance Center (TAC) by one of the following methods:

• Open a service request on Cisco.com
• By email
• By telephone