There is a potential denial-of-service attack at ISPs that targets network devices.
User Datagram Protocol (UDP) diagnostic port attack: A sender transmits a volume of requests for UDP diagnostic services on the router. This causes all CPU resources to be consumed to service the phony requests.
This document describes how the potential UDP diagnostic port attack occurs and suggests the methods to use with Cisco IOS® software in order to defend against it.
There are no specific requirements for this document.
This document is not restricted to specific software and hardware versions. Some of the commands referred to in this document are only available starting in Cisco IOS Software Releases 10.2(9), 10.3(7), and 11.0(2), and all subsequent releases. These commands are the default in Cisco IOS Software Release 12.0 and later.
For more information on document conventions, refer to the Cisco Technical Tips Conventions.
By default, the Cisco router has a series of diagnostic ports enabled for certain UDP and TCP services. These services include echo, chargen, and discard. When a host attaches to these ports, a small amount of CPU capacity is consumed to service these requests.
If a single attacking device sends a large barrage of requests with different, random, phony source IP addresses, it is possible that the Cisco router becomes overwhelmed and slows down or fails.
The external manifestation of the problem includes a process table full error message (%SYS-3 NOPROC) or a very high CPU utilization. The exec command show process shows a lot of processes with the same name, such as "UDP Echo."
Any network device that has UDP and TCP diagnostic services needs to be protected by a firewall or have the services disabled. For a Cisco router, this can be accomplished by using these global configuration commands.
no service udp-small-servers no service tcp-small-servers
See the Appendix for further information on these commands. The commands are available starting in Cisco IOS Software Releases 10.2(9), 10.3(7), and 11.0(2) and all subsequent releases. These commands are the default in Cisco IOS Software Release 12.0 and later.
Since a primary mechanism of denial-of-service attacks is the generation of traffic sourced from random IP addresses, Cisco recommends filtering traffic destined for the Internet. The basic concept is to throw away packets with invalid source IP addresses as they enter the Internet. This does not prevent the denial-of-service attack on your network. However, it helps the attacked parties rule out your location as the source of the attacker. In addition, it prevents the use of your network for this class of attacks.
By filtering packets on your routers that connect your network to the Internet, you can permit only packets with valid source IP addresses to leave your network and get into the Internet.
For example, if your network consists of network 172.16.0.0, and your router connects to your ISP using a FDDI0/1 interface, you can apply the access list like this:
access-list 111 permit ip 172.16.0.0 0.0.255.255 any access-list 111 deny ip any any log ¹ interface Fddi 0/1 ip access-group 111 out
¹ The last line of the access list determines if there is any traffic with an invalid source address that enters the Internet. This helps to locate the source of the possible attacks.
For ISPs who provide service to end networks, Cisco highly recommends the validation of incoming packets from your clients. This can be accomplished by the use of inbound packet filters on your border routers.
For example, if your clients have these network numbers connected to your router through an FDDI interface named "FDDI 1/0", you can create this access list.
The network numbers are 192.168.0.0 to 192.168.15.0, and 172.18.0.0 access-list 111 permit ip 192.168.0.0 0.0.15.255 any access-list 111 permit ip 172.18.0.0 0.0.255.255 any access-list 111 deny ip any any log interface Fddi 1/0 ip access-group 111 in
Note: The last line of the access list determines if there is any traffic with an invalid source address that enters the Internet. This helps to locate the source of the possible attack.
The small servers are servers (daemons, in UNIX parlance) that run in the router which are useful for diagnostics. Therefore, they are on by default.
The commands for the TCP and UDP small servers are:
If you do not want your router to provide any non-routing services, turn them off (using the no form of the previous commands).
The TCP small servers are:
Echo—Echoes back whatever you type. Type the command telnet x.x.x.x echo to see.
Chargen—Generates a stream of ASCII data. Type the command telnet x.x.x.x chargen to see.
Discard—Throws away whatever you type. Type the command telnet x.x.x.x discard to see.
Daytime—Returns system date and time, if correct. It is correct if you run NTP or have set the date and time manually from the exec level. Type the command telnet x.x.x.x daytime to see.
The UDP small servers are:
Echo—Echoes the payload of the datagram you send.
Discard—Silently pitches the datagram you send.
Chargen—Pitches the datagram you send and responds with a 72 character string of ASCII characters terminated with a CR+LF.
Note: Almost all UNIX boxes support the small servers previously listed. The router also offers finger service and async line bootp service. These can be independently turned off with the configuration global commands no service finger and no ip bootp server, respectively.
The Cisco Support Community is a forum for you to ask and answer questions, share suggestions, and collaborate with your peers.
Refer to Cisco Technical Tips Conventions for information on conventions used in this document.