The Authentication Proxy feature allows users to log in to the network or access the Internet via HTTP, with their specific access profiles automatically retrieved and applied from a RADIUS, or TACACS+ server. The user profiles are active only when there is active traffic from the authenticated users.
This sample configuration blocks traffic from the host device (at 184.108.40.206) on the internal network to all devices on the Internet until browser authentication is performed with the use of Authentication Proxy. The access control list (ACL) passed down from the server (permit tcp|ip|icmp any any) adds dynamic entries post-authorization to access list 116 that temporarily allow access from the host PC to the Internet.
Refer to Configuring Authentication Proxy for more information on Authentication Proxy.
There are no specific requirements for this document.
The information in this document is based on these software and hardware versions:
Cisco IOS® Software Release 12.2(15)T
Cisco 7206 router
Note: The ip auth-proxy command was introduced in Cisco IOS Firewall Software Release 12.0.5.T.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Refer to Cisco Technical Tips Conventions for more information on document conventions.
In this section, you are presented with the information to configure the features described in this document.
This document uses this network setup:
This document uses this configuration:
version 12.2 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname psy-rtr-2 ! logging queue-limit 100 ! username admin password 7 <deleted> aaa new-model !--- Enable AAA. aaa authentication login default group radius none !--- Use RADIUS to authenticate users. aaa authorization exec default group radius none aaa authorization auth-proxy default group radius !--- Utilize RADIUS for auth-proxy authorization. aaa session-id common ip subnet-zero ! ip cef ! ip auth-proxy auth-proxy-banner !--- Displays the name of the firewall router !--- in the Authentication Proxy login page. ip auth-proxy auth-cache-time 10 !--- Sets the global Authentication Proxy idle !--- timeout value in minutes. ip auth-proxy name restrict_pc http !--- Associates connections that initiate HTTP traffic with !--- the "restrict_pc" Authentication Proxy name. ip audit notify log ip audit po max-events 100 ! no voice hpi capture buffer no voice hpi capture destination ! mta receive maximum-recipients 0 ! ! interface FastEthernet0/0 ip address 192.168.10.10 255.255.255.0 ip access-group 116 in !--- Apply access list 116 in the inbound direction. ip auth-proxy restrict_pc !--- Apply the Authentication Proxy list !--- "restrict_pc" configured earlier. duplex full ! interface FastEthernet4/0 ip address 10.89.129.195 255.255.255.240 duplex full ! ip classless ip http server !--- Enables the HTTP server on the router. !--- The Authentication Proxy uses the HTTP server to communicate !--- with the client for user authentication. ip http authentication aaa !--- Sets the HTTP server authentication method to AAA. ! access-list 116 permit tcp host 192.168.10.200 host 192.168.10.10 eq www !--- Permit HTTP traffic (from the PC) to the router. access-list 116 deny tcp host 192.168.10.200 any access-list 116 deny udp host 192.168.10.200 any access-list 116 deny icmp host 192.168.10.200 any !--- Deny TCP, UDP, and ICMP traffic from the client by default. access-list 116 permit tcp 192.168.10.0 0.0.0.255 any access-list 116 permit udp 192.168.10.0 0.0.0.255 any access-list 116 permit icmp 192.168.10.0 0.0.0.255 any !--- Permit TCP, UDP, and ICMP traffic from other !--- devices in the 192.168.10.0/24 network. ! radius-server host 192.168.10.103 auth-port 1645 acct-port 1646 key 7 <deleted> !--- Specify the IP address of the RADIUS !--- server along with the key. radius-server authorization permit missing Service-Type call rsvp-sync ! ! line con 0 stopbits 1 line aux 0 stopbits 1 line vty 0 4 ! end
This section provides screen captures taken from the PC that show the authentication procedure. The first capture shows the window where a user enters the username and password for authentication and presses OK.
If authentication is successful, this window appears.
The RADIUS server must be configured with the proxy ACLs that are applied. In this example, these ACL entries are applied. This permits the PC to connect to any device.
permit tcp host 192.168.10.200 any permit udp host 192.168.10.200 any permit icmp host 192.168.10.200 any
This Cisco ACS window shows where to enter the proxy ACLs.
Note: Refer to Configuring Authentication Proxy for more information on how to configure the RADIUS/TACACS+ server.
This section provides information you can use to confirm your configuration works properly.
show ip access-lists—Displays the standard and extended ACLs configured on the firewall (includes dynamic ACL entries). The dynamic ACL entries are added and removed periodically based on whether the user authenticates or not.
show ip auth-proxy cache—Displays either the Authentication Proxy entries or the running Authentication Proxy configuration. The cache keyword to list the host IP address, the source port number, the timeout value for the Authentication Proxy, and the state for connections that use Authentication Proxy. If the Authentication Proxy state is HTTP_ESTAB, the user authentication is a success.
This section provides information you can use to troubleshoot your configuration.
For these commands, along with other troubleshooting information, refer to Troubleshooting Authentication Proxy.
Note: Refer to Important Information on Debug Commands before you use debug commands.
The Cisco Support Community is a forum for you to ask and answer questions, share suggestions, and collaborate with your peers.
Refer to Cisco Technical Tips Conventions for information on conventions used in this document.