Table Of Contents
Catalyst 6500 Series Wireless LAN Services Module Installation and Verification Note
Front Panel Description
CONSOLE Port
STATUS LED
FIPS LED
SHUTDOWN Button
System Requirements
Safety Overview
Preparing to Install the Wireless LAN Services Module
Required Tools
Installing the Wireless LAN Services Module
Verifying the Installation
Removing the Wireless LAN Services Module
Related Documentation
Obtaining Documentation
Cisco.com
Ordering Documentation
Documentation Feedback
Obtaining Technical Assistance
Cisco Technical Support Website
Submitting a Service Request
Definitions of Service Request Severity
Obtaining Additional Publications and Information
Catalyst 6500 Series Wireless LAN Services Module Installation and Verification Note
Product number: WS-SVC-WLAN-1-K9
This document provides installation procedures for the Catalyst 6500 series Wireless LAN Services Module and contains these sections:
•
Front Panel Description
•System Requirements
•Safety Overview
•Preparing to Install the Wireless LAN Services Module
•Required Tools
•Installing the Wireless LAN Services Module
•Verifying the Installation
•Removing the Wireless LAN Services Module
•Related Documentation
•Obtaining Documentation
•Documentation Feedback
•Obtaining Technical Assistance
•Obtaining Additional Publications and Information
Front Panel Description
The Wireless LAN Services Module front panel (Figure 1) includes a STATUS LED, a Federal Information Processing Standards (FIPS) LED, a SHUTDOWN button, and a CONSOLE port.
Figure 1 Wireless LAN Services Module Front Panel
These sections describe the Wireless LAN Services Module front panel:
•CONSOLE Port
•STATUS LED
•FIPS LED
•SHUTDOWN Button
CONSOLE Port
The CONSOLE port is used for the initial configuration of the Wireless LAN Services Module.
Note The initial Wireless LAN Services Module configuration must be made through a direct connection to the CONSOLE port. After the initial configurations, you can make an SSH or Telnet connection to the module to further configure the module.
STATUS LED
The STATUS LED indicates the operating states of the module. Table 1 describes the STATUS LED operation.
Table 1 STATUS LED Description
Color
|
State
|
Description
|
Green
|
On
|
All diagnostic tests pass. The module is receiving power.
|
Red
|
On
|
A diagnostic other than an individual port test failed.
|
Orange
|
On
|
Indicates one of three conditions:
•The module is running through its boot and self-test diagnostic sequence.
•The module is disabled.
•The module is in the shutdown state.
|
| |
Off
|
The module power is off.
|
FIPS LED
The FIPS LED currently is not used.
SHUTDOWN Button
Caution Do not remove the Wireless LAN Services Module from the switch until the module has shut down completely and the STATUS LED is orange. You can damage the module if you remove it from the switch before it completely shuts down.
To avoid corrupting the Wireless LAN Services Module compact flash memory card, you must correctly shut down the Wireless LAN Services Module before you remove it from the chassis or disconnect the power. You can shut down the module by entering the hw-mod module mod shutdown command in privileged mode from the router CLI.
If the Wireless LAN Services Module fails to respond to this command, shut down the module by pressing the SHUTDOWN button on the front panel.
The shutdown procedure may require several minutes. The STATUS LED turns off when the module shuts down.
See the "Removing the Wireless LAN Services Module" section for detailed procedures on shutting down the Wireless LAN Services Module.
System Requirements
Before you install the Wireless LAN Services Module into the Catalyst 6500 series switch, refer to the Release Notes for Catalyst 6500 Series Wireless LAN Mobility Module to make sure that the switch meets the hardware and software requirements.
Safety Overview
Safety warnings appear throughout this publication in procedures that, if performed incorrectly, may harm you. A warning symbol precedes each warning statement.
|
Warning
|
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071
SAVE THESE INSTRUCTIONS
|
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030
Warning Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when servicing. Statement 1034
Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029
Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. Statement 1017
Preparing to Install the Wireless LAN Services Module
Note Before installing the Wireless LAN Services Module, you must install the Catalyst 6500 series switch chassis and at least one supervisor engine. For information on installing the switch chassis, refer to the Catalyst 6500 Series Switch Installation Guide.
Before installing the Wireless LAN Services Module, make sure that the following items are available:
•Catalyst 6500 series switch chassis
•Management station that is available through a console connection to perform configuration tasks
Required Tools
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030
These tools are required to install the Wireless LAN Services Module into the Catalyst 6500 series switch:
•Flat-blade screwdriver
•Wrist strap or other grounding device
•Antistatic mat or antistatic foam
Installing the Wireless LAN Services Module
Note Before installing the Wireless LAN Services Module, you must install the Catalyst 6500 series switch chassis and at least one supervisor engine. For information on installing the switch chassis, refer to the Catalyst 6500 Series Switch Installation Guide.
This section describes how to install the Wireless LAN Services Module into the Catalyst 6500 series switch.
Note All modules, including the supervisor engine (if you have redundant supervisor engines), support hot swapping. You can add, replace, or remove modules without interrupting the system power or causing other software or interfaces to shut down. For more information about hot-swapping modules, refer to the Catalyst 6500 Series Switch Module Installation Guide.
Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94
To install the Wireless LAN Services Module into the Catalyst 6500 series switch, perform these steps:
Step 1 Make sure that you take the necessary precautions to prevent ESD damage.
Step 2 Choose a slot for the Wireless LAN Services Module. See Figure 2 for the slot numbers on a Catalyst 6500 series switch.
Figure 2 Slot Numbers on Catalyst 6500 Series Switches
Step 3 Check that there is enough clearance to accommodate any interface equipment that you will be connecting directly to the supervisor engine or switching module ports.
Note If possible, place switching modules between the empty slots that contain only switching-module filler plates (Cisco part number 800-00292-01).
Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029
Step 4 Loosen the captive installation screws that secure the switching module filler plate (or an existing switching module) to the desired slot.
Step 5 Remove the switching module filler plate (or an existing switching module).
Step 6 Hold the handle of the Wireless LAN Services Module with one hand, and place your other hand under the carrier support. Do not touch the printed circuit boards or connector pins.
Step 7 Place the Wireless LAN Services Module in the slot. Align the notch on the sides of the switching module carrier with the groove in the slot. (See Figure 3.)
Step 8 Keep the Wireless LAN Services Module at a 90-degree angle to the backplane and carefully slide the Wireless LAN Services Module into the slot until the switching module faceplate contacts the ejector levers. (See Figure 4.)
Step 9 Using the thumb and forefinger of each hand, simultaneously push in the left and right levers to fully seat the Wireless LAN Services Module in the backplane connector.
Caution Always use the ejector levers when installing or removing the Wireless LAN Services Module. A module that is partially seated in the backplane will cause the system to halt and subsequently crash.
Note If you perform a hot swap, the console displays the message "Module n has been inserted." This message does not appear if you are connected to the Catalyst 6500 series switch through a Telnet session.
Step 10 Use a screwdriver to tighten the captive installation screws on the left and right ends of the Wireless LAN Services Module.
Figure 3 Installing Modules in the Catalyst 6500 Series Switch
Figure 4 Ejector Levers and Captive Installation Screws
This completes the Wireless LAN Services Module installation procedure.
Verifying the Installation
When you install the Wireless LAN Services Module into the Catalyst 6500 series switch, the module goes through a boot sequence that requires no intervention. At the successful conclusion of the boot sequence, the green STATUS LED will light and remain on. If the STATUS LED is not green, or is a different color, see Table 1 to determine the status of the module.
Enter the show module command to verify the installation:
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 16 SFM-capable 16 port 10/100/1000mb RJ45 WS-X6516-GE-TX SAL064893ST
2 6 Firewall Module WS-SVC-FWM-1 SAD0707017D
4 8 Intrusion Detection System WS-SVC-IDSM-2 SAD072001DF
5 1 Wireless LAN Module WS-SVC-WLAN-1-K9 SAD074901K2
6 2 Supervisor Engine 720 (Active) WS-SUP720-BASE SAD07260096
5 Pass
Removing the Wireless LAN Services Module
This section describes how to remove the Wireless LAN Services Module from the Catalyst 6500 series switch.
Caution Do not remove the Wireless LAN Services Module from the switch until the module has shut down completely and the STATUS LED is orange or off. You can damage the module if you remove it from the switch before it completely shuts down.
Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94
To remove the Wireless LAN Services Module, perform these steps:
Step 1 Shut down the module by one of these methods:
•In privileged mode from the router prompt, enter the hw-mod module mod shutdown command.
Note If you enter this command to shut down the module, you will have to enter the following commands in config mode to restart (power down, and then power up) the module:
Router# no power enable module mod
Router# power enable module mod
•If the module does not respond to any commands, press the SHUTDOWN button located on the front panel of the module.
Note Shutdown may require several minutes.
Step 2 Verify that the Wireless LAN Mobility Module shuts down. Do not remove the module from the switch until the STATUS LED is off or orange.
Step 3 Use a screwdriver to loosen the captive installation screws at the left and right sides of the module.
Step 4 Grasp the left and right ejector levers. Simultaneously, pull the left lever to the left and the right lever to the right to release the module from the backplane connector.
Step 5 As you pull the module out of the slot, place one hand under the carrier to support it. Avoid touching the module itself.
Step 6 Carefully pull the module straight out of the slot, keeping one hand under the carrier to guide it. Keep the module at a 90-degree orientation to the backplane (horizontal to the floor).
Step 7 Place the removed module on an antistatic mat or antistatic foam.
Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029
Step 8 If the slot is to remain empty, install a module filler plate to keep dust out of the chassis and to maintain proper airflow through the module compartment.
Related Documentation
For more detailed installation and configuration information, refer to the following publications:
•Release Notes for Catalyst 6500 Series Wireless LAN Services Module
•Catalyst 6500 Series Switch Installation Guide
•Catalyst 6500 Series Switch Module Installation Guide
•Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide
•Catalyst 6500 Series Switch Cisco IOS Command Reference
•Regulatory Compliance and Safety Information for the Catalyst 6500 Series Switches
•Site Preparation and Safety Guide
Obtaining Documentation
Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems.
Cisco.com
You can access the most current Cisco documentation at this URL:
http://www.cisco.com/univercd/home/home.htm
You can access the Cisco website at this URL:
http://www.cisco.com
You can access international Cisco websites at this URL:
http://www.cisco.com/public/countries_languages.shtml
Ordering Documentation
You can find instructions for ordering documentation at this URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm
You can order Cisco documentation in these ways:
•Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Ordering tool:
http://www.cisco.com/en/US/partner/ordering/index.shtml
•Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in North America, by calling 800 553-NETS (6387).
Documentation Feedback
You can send comments about technical documentation to bug-doc@cisco.com.
You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address:
Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883
We appreciate your comments.
Obtaining Technical Assistance
For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco Technical Support provides 24-hour-a-day, award-winning technical assistance. The Cisco Technical Support Website on Cisco.com features extensive online support resources. In addition, Cisco Technical Assistance Center (TAC) engineers provide telephone support. If you do not hold a valid Cisco service contract, contact your reseller.
Cisco Technical Support Website
The Cisco Technical Support Website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The website is available 24 hours a day, 365 days a year at this URL:
http://www.cisco.com/techsupport
Access to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password. If you have a valid service contract but do not have a user ID or password, you can register at this URL:
http://tools.cisco.com/RPF/register/register.do
Submitting a Service Request
Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Service Request Tool automatically provides recommended solutions. If your issue is not resolved using the recommended resources, your service request will be assigned to a Cisco TAC engineer. The TAC Service Request Tool is located at this URL:
http://www.cisco.com/techsupport/servicerequest
For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.
To open a service request by telephone, use one of the following numbers:
Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553 2447
For a complete list of Cisco TAC contacts, go to this URL:
http://www.cisco.com/techsupport/contacts
Definitions of Service Request Severity
To ensure that all service requests are reported in a standard format, Cisco has established severity definitions.
Severity 1 (S1)—Your network is "down," or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.
Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your business operation are negatively affected by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normal business hours to resolve the situation.
Severity 3 (S3)—Operational performance of your network is impaired, but most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels.
Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations.
Obtaining Additional Publications and Information
Information about Cisco products, technologies, and network solutions is available from various online and printed sources.
•Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit Cisco Marketplace, the company store, at this URL:
http://www.cisco.com/go/marketplace/
•The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as ordering and customer support services. Access the Cisco Product Catalog at this URL:
http://cisco.com/univercd/cc/td/doc/pcat/
•Cisco Press publishes a wide range of general networking, training and certification titles. Both new and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press at this URL:
http://www.ciscopress.com
•Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and networking investments. Each quarter, Packet delivers coverage of the latest industry trends, technology breakthroughs, and Cisco products and solutions, as well as network deployment and troubleshooting tips, configuration examples, customer case studies, certification and training information, and links to scores of in-depth online resources. You can access Packet magazine at this URL:
http://www.cisco.com/packet
•iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies learn how they can use technology to increase revenue, streamline their business, and expand services. The publication identifies the challenges facing these companies and the technologies to help solve them, using real-world case studies and business strategies to help readers make sound technology investment decisions. You can access iQ Magazine at this URL:
http://www.cisco.com/go/iqmagazine
•Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL:
http://www.cisco.com/ipj
•World-class networking training is available from Cisco. You can view current offerings at this URL:
http://www.cisco.com/en/US/learning/index.html
This document is to be used in conjunction with the documents listed in the "Related Documentation" section.
Copyright © 2004 Cisco Systems, Inc. All rights reserved.
