Table Of Contents
Cisco Wireless LAN Controller
Command ReferenceSHOW ADVANCED 802.11A COMMANDS
show advanced 802.11a receiver
SHOW ADVANCED 802.11B COMMANDS
show advanced 802.11b receiver
show advanced send-disassoc-on-handoff
show certificate compatibility
show radius rfc3576 statistics
config 802.11a antenna extAntGain
config 802.11a antenna diversity
config 802.11a antenna selection
config 802.11b antenna diversity
config 802.11b antenna extAntGain
config 802.11b antenna selection
config 802.11h powerconstraint
CONFIG ADVANCED 802.11A COMMANDS
config advanced 802.11a channel foreign
config advanced 802.11a channel load
config advanced 802.11a channel noise
config advanced 802.11a channel update
config advanced 802.11a factory
config advanced 802.11a group-mode
config advanced 802.11a logging channel
config advanced 802.11a logging coverage
config advanced 802.11a logging foreign
config advanced 802.11a logging load
config advanced 802.11a logging noise
config advanced 802.11a logging performance
config advanced 802.11a logging txpower
config advanced 802.11a monitor channel-list
config advanced 802.11a monitor coverage
config advanced 802.11a monitor load
config advanced 802.11a monitor mode
config advanced 802.11a monitor noise
config advanced 802.11a monitor signal
config advanced 802.11a profile clients
config advanced 802.11a profile coverage
config advanced 802.11a profile customize
config advanced 802.11a profile exception
config advanced 802.11a profile foreign
config advanced 802.11a profile level
config advanced 802.11a profile noise
config advanced 802.11a profile throughput
config advanced 802.11a profile utilization
config advanced 802.11a receiver
config advanced 802.11a txpower-update
CONFIG ADVANCED 802.11B COMMANDS
config advanced 802.11b 7920VSIEConfig
config advanced 802.11b channel foreign
config advanced 802.11b channel load
config advanced 802.11b channel noise
config advanced 802.11b channel update
config advanced 802.11b factory
config advanced 802.11b group-mode
config advanced 802.11b logging channel
config advanced 802.11b logging coverage
config advanced 802.11b logging foreign
config advanced 802.11b logging load
config advanced 802.11b logging noise
config advanced 802.11b logging performance
config advanced 802.11b logging txpower
config advanced 802.11b monitor channel-list
config advanced 802.11b monitor coverage
config advanced 802.11b monitor load
config advanced 802.11b monitor mode
config advanced 802.11b monitor noise
config advanced 802.11b monitor signal
config advanced 802.11b profile clients
config advanced 802.11b profile coverage
config advanced 802.11b profile customize
config advanced 802.11b profile exception
config advanced 802.11b profile foreign
config advanced 802.11b profile level
config advanced 802.11b profile noise
config advanced 802.11b profile throughput
config advanced 802.11b profile utilization
config advanced 802.11b receiver
config advanced 802.11b txpower-update
config advanced client-handoff
CONFIG ADVANCED TIMERS COMMANDS
config advanced timers ap-discovery-timeout
config advanced timers ap-heartbeat-timeout
config advanced timers auth-timeout
config advanced timers eap-timeout
config advanced timers eap-identity-request-delay
config ap crash-file clear-all
config ap crash-file get-crash-file
config ap crash-file get-radio-core-dump
config custom-web ext-webauth-mode
config custom-web ext-webauth-url
config custom-web ext-webserver
config location interface-mapping
config macfilter mac-delimiter
config macfilter radius-compat
config mobility statistics reset
config network allow-old-bridge-aps
config network bridging-shared-secret
config network fast-ssid-change
config network mgmt-via-wireless
config network rf-network-name
config port multicast appliance
config radius acct ipsec authentication
config radius acct ipsec disable
config radius acct ipsec enable
config radius acct ipsec encryption
config radius acct retransmit-timeout
config radius auth ipsec authentication
config radius auth ipsec disable
config radius auth ipsec enable
config radius auth ipsec encryption
config radius auth retransmit-timeout
config radius backward compatibility
config radius callStationIdType
CONFIG SNMP COMMUNITY COMMANDS
config snmp community accessmode
CONFIG SNMP TRAPRECEIVER COMMANDS
config snmp trapreceiver create
config snmp trapreceiver delete
CONFIG SPANNINGTREE PORT COMMANDS
config spanningtree port pathcost
config spanningtree port priority
CONFIG SPANNINGTREE SWITCH COMMANDS
config spanningtree switch bridgepriority
config spanningtree switch forwarddelay
config spanningtree switch hellotime
config spanningtree switch maxage
config spanningtree switch mode
config switchconfig flowcontrol
config trapflags 802.11-Security
config trapflags authentication
CONFIG WIRELESS LAN SECURITY COMMANDS
config wlan security ipsec disable
config wlan security ipsec enable
config wlan security ipsec authentication
config wlan security ipsec encryption
config wlan security ipsec config
config wlan security ipsec ike authentication
config wlan security ipsec ike dh-group
config wlan security ipsec ike lifetime
config wlan security ipsec ike phase1
config wlan security ipsec ike contivity
config wlan security static-wep-key authentication
config wlan security static-wep-key disable
config wlan security static-wep-key enable
config wlan security static-wep-key encryption
config wlan security web-passthrough acl
config wlan security web-passthrough disable
config wlan security web-passthrough email-input
config wlan security web-passthrough enable
config wlan security wpa1 disable
config wlan security wpa1 enable
config wlan security wpa1 pre-shared-key
config wlan security wpa2 disable
config wlan security wpa2 enable
config wlan security wpa2 pre-shared-key
config wlan security wpa2 tkip
config wlan security wpa2 wpa-compat
Clearing Configurations, Logfiles, and Other Actions
Uploading and Downloading Files and Configurations
transfer download certpassword
transfer download tftpPktTimeout
transfer download tftpMaxRetries
Cisco Wireless LAN Controller
Command Reference
The Cisco Wireless LAN Solution command line interface (CLI) enables operators to connect an ASCII console to the Cisco Wireless LAN Controller and configure the controller and its associated access points.
This document covers the commands available in the Cisco CLI release 4.0 on all the controllers listed in the Compatibility Matrix in Appendix A. This compatibility matrix allows the user to determine what commands operate on any individual controller. The controllers currently covered include:
•
WiSM
•
•
This chapter contains the following sections:
•
•
Using the ? command
To display all of the commands in your current level of the command tree, or to display more information about a particular command, use the ? command.
?
command name ?
When you enter a command information request, put a space between command name and ?.
Examples
The following command shows you all the commands and levels available from the root level.
> ?clear Clear selected configuration elements.config Configure switch options and settings.debug Manages system debug options.help Helplinktest Perform a link test to a specified MAC address.logout Exit this session. Any unsaved changes are lost.ping Send ICMP echo packets to a specified IP address.reset Reset options.save Save switch configurations.show Display switch options and settings.transfer Transfer a file to or from the switch.The following command shows you that datatype is the only entry at the transfer download level:
> transfer download d?datatypeThe following command shows you the permissible entries for the transfer download datatype command:
> transfer download datatype ?config Download Configuration File.code Download an executable image to the system.image Download a web page logo to the system.signature Download a signature file to the system.webadmincert Download a certificate for web administration to the system.webauthcert Download a web certificate for web portal to the system.Using the Help Command
To look up keyboard commands, use the help command at the root level.
help
Examples
> helpHELP:Special keys:DEL, BS... delete previous characterCtrl-A .... go to beginning of lineCtrl-E .... go to end of lineCtrl-F .... go forward one characterCtrl-B .... go backward one characterCtrl-D .... delete current characterCtrl-U, X. delete to beginning of lineCtrl-K .... delete to end of lineCtrl-W .... delete previous wordCtrl-T .... transpose previous characterCtrl-P .... go to previous line in history bufferCtrl-N .... go to next line in history bufferCtrl-Z .... return to root command promptTab, <SPACE> command-line completionExit .... go to next lower command prompt? .... list choicesViewing Configurations
To view Cisco Wireless LAN controller options and settings, use the show commands.
show 802.11a
To display basic 802.11a options and settings, use the show 802.11a command.
show 802.11a
Syntax Description
Defaults
None.
Examples
> show 802.11a802.11a Network................................. Enabled802.11a Low Band......................... Enabled802.11a Mid Band......................... Enabled802.11a High Band........................ Enabled802.11a Operational Rates802.11a 6M Rate............................ Mandatory802.11a 9M Rate............................ Supported802.11a 12M Rate........................... Mandatory802.11a 18M Rate........................... Supported802.11a 24M Rate........................... Mandatory802.11a 36M Rate........................... Supported802.11a 48M Rate........................... Supported802.11a 54M Rate........................... SupportedBeacon Interval................................. 100CF Pollable mandatory........................... DisabledCF Poll Request mandatory....................... DisabledCFP Period...................................... 4CFP Maximum Duration............................ 100Default Channel................................. 36Default Tx Power Level.......................... 1DTPC Status..................................... EnabledDTIM Period..................................... 10Fragmentation Threshold......................... 2346Long Retry Limit................................ 4Maximum Rx Life Time............................ 512Max Tx MSDU Life Time........................... 512Medium Occupancy Limit.......................... 100Pico-Cell Status................................ DisabledRTS Threshold................................... 2347Short Retry Limit............................... 7TI Threshold.................................... -50Related Commands
show 802.11b, show advanced 802.11a channel, show advanced 802.11a group, show advanced 802.11a logging, show advanced 802.11a monitor, show advanced 802.11a power, show advanced 802.11a profile, show advanced 802.11a summary
show 802.11b
To display basic 802.11b/g options and settings, use the show 802.11b command.
show 802.11b
Syntax Description
Defaults
None.
Examples
> show 802.11b802.11b Network.................................. Enabled11gSupport....................................... Enabled802.11b/g Operational Rates802.11b/g 1M Rate............................ Mandatory802.11b/g 2M Rate............................ Mandatory802.11b/g 5.5M Rate.......................... Mandatory802.11b/g 11M Rate........................... Mandatory802.11g 6M Rate.............................. Supported802.11g 9M Rate.............................. Supported802.11g 12M Rate............................. Supported802.11g 18M Rate............................. Supported802.11g 24M Rate............................. Supported802.11g 36M Rate............................. Supported802.11g 48M Rate............................. Supported802.11g 54M Rate............................. SupportedBeacon Interval.................................. 100CF Pollable mode................................. DisabledCF Poll Request mandatory........................ DisabledCFP Period....................................... 4CFP Maximum Duration............................. 60Default Channel.................................. 1Default Tx Power Level........................... 1DTPC Status..................................... EnabledCall Admission Limit ........................... 105G711 CU Quantum ................................. 15DTIM Period...................................... 1ED Threshold..................................... -50Fragmentation Threshold.......................... 2346Long Retry Limit................................. 4Maximum Rx Life Time............................. 512Max Tx MSDU Life Time............................ 512Medium Occupancy Limit........................... 100PBCC mandatory................................... DisabledPico-Cell Status................................. DisabledRTS Threshold.................................... 2347Short Preamble mandatory......................... EnabledShort Retry Limit................................ 7Related Commands
show 802.11a, show advanced 802.11b channel, show advanced 802.11b group, show advanced 802.11b logging, show advanced 802.11b monitor, show advanced 802.11b txpower, show advanced 802.11b profile, show advanced 802.11b summary
show 802.11h
To display basic 802.11h options and settings, use the show 802.11h command.
show 802.11h
Syntax Description
Defaults
None.
Examples
> show 802.11h802.11h ......................................... powerconstraint : 0802.11h ......................................... channelswitch : Disable802.11h ......................................... channelswitch mode : 0Related Commands
show 802.11a, show 802.11b, config 802.11h
show acl
To display the access control lists (ACLs) that are configured on the controller, use the show acl command.
show acl {summary | detailed acl_name}
Syntax Description
Defaults
None.
Examples
> show acl summaryACL Name Applied-------------------------------- -------Pubs Only YesMannina YesRelated Commands
config interface acl
show acl cpu
To display the access control lists (ACLs) configured on the central processing unit (CPU), use the show acl cpu command.
show acl cpu
Syntax Description
Command Default
None
Examples
> show acl cpuCPU Acl Name................................Wireless Traffic............................ DisabledWired Traffic............................... DisabledApplied to NPU.............................. NoRelated Commands
config acl cpu
SHOW ADVANCED 802.11A COMMANDS
Use the SHOW ADVANCED 802.11a commands to display advanced 802.11a configuration parameters.
Show advanced 802.11a channel
To display the automatic channel assignment configuration and statistics, use the show advanced 802.11a channel command.
show advanced 802.11a channel
Syntax Description
show
Display configurations.
advanced
Advanced parameters.
802.11a
802.11a network.
channel
Channel status.
Defaults
None.
Examples
> show advanced 802.11a channelAutomatic Channel AssignmentChannel Assignment Mode........................ AUTOChannel Update Interval........................ 600 secondsChannel Update Contribution.................... SNI.Channel Assignment Leader...................... xx:xx:xx:xx:xx:xxLast Run....................................... 374 seconds agoChannel Energy LevelsMinimum...................................... -84 dBmAverage...................................... -84 dBmMaximum...................................... -84 dBmChannel Dwell TimesMinimum...................................... 0 days, 19 h 07 m 57 sAverage...................................... 0 days, 19 h 08 m 29 sMaximum...................................... 0 days, 19 h 09 m 11 sRelated Commands
config 802.11a channel
show advanced 802.11a group
To display the advanced 802.11a Cisco radio RF grouping, use the show advanced 802.11a group command.
show advanced 802.11a group
Syntax Description
show
Display configurations.
advanced
Advanced parameters.
802.11a
802.11a network.
group
RF grouping values.
Defaults
None.
Examples
> show advanced 802.11a groupRadio RF Grouping802.11a Group Mode................................... AUTO802.11a Group Update Interval........................ 600 seconds802.11a Group Leader................................. xx:xx:xx:xx:xx:xx802.11a Group Member............................... xx:xx:xx:xx:xx:xx802.11a Last Run..................................... 133 seconds agoRelated Commands
config advanced 802.11a group-mode
show advanced 802.11a logging
To display advanced 802.11a RF event and performance logging, use the show advanced 802.11a logging command.
show advanced 802.11a logging
Syntax Description
show
Display configurations.
advanced
Advanced parameters.
802.11a
802.11a network.
logging
RF event and performance logging.
Defaults
None.
Examples
> show advanced 802.11a loggingRF Event and Performance LoggingChannel Update Logging......................... OffCoverage Profile Logging....................... OffForeign Profile Logging........................ OffLoad Profile Logging........................... OffNoise Profile Logging.......................... OffPerformance Profile Logging.................... OffTxPower Update Logging......................... OffRelated Commands
config advanced 802.11a logging channel, config advanced 802.11a logging coverage, config advanced 802.11a logging foreign, config advanced 802.11a logging load, config advanced 802.11a logging noise, config advanced 802.11a logging performance, config advanced 802.11a logging power
show advanced 802.11a monitor
To display the advanced 802.11a default Cisco radio monitoring, use the show advanced 802.11a monitor command.
show advanced 802.11a monitor
Syntax Description
show
Display configurations.
advanced
Advanced parameters.
802.11a
802.11a network.
monitor
Cisco radio monitoring values.
Defaults
None.
Examples
> show advanced 802.11a monitorDefault 802.11a AP monitoring802.11a Monitor Mode........................... enable802.11a Monitor Channels....................... Country channels802.11a AP Coverage Interval................... 180 seconds802.11a AP Load Interval....................... 60 seconds802.11a AP Noise Interval...................... 180 seconds802.11a AP Signal Strength Interval............ 60 secondsRelated Commands
config advanced 802.11a monitor coverage, config advanced 802.11a monitor load, config advanced 802.11a monitor noise, config advanced 802.11a monitor signal
show advanced 802.11a profile
To display the advanced 802.11a Cisco 1000 series lightweight access point performance profiles, use the show advanced 802.11a profile command.
show advanced 802.11a profile {global | Cisco_AP}
Syntax Description
Defaults
None.
Examples
> show advanced 802.11a profile globalDefault 802.11a AP performance profiles802.11a Global Interference threshold.............. 10%802.11a Global noise threshold..................... -70 dBm802.11a Global RF utilization threshold............ 80%802.11a Global throughput threshold................ 1000000 bps802.11a Global clients threshold................... 12 clients802.11a Global coverage threshold.................. 12 dB802.11a Global coverage exception level............ 80%802.11a Global client minimum exception lev........ 3 clients> show advanced 802.11a profile AP1Cisco 1000 series lightweight access point performance profile not customizedThis response indicates that the performance profile for this Cisco 1000 series lightweight access point is using the global defaults and has not been individually configured.
Related Commands
config advanced 802.11b profile clients, config advanced 802.11b profile coverage, config advanced 802.11b profile customize, config advanced 802.11b profile exception, config advanced 802.11b profile foreign, config advanced 802.11b profile level, config advanced 802.11b profile noise, config advanced 802.11b profile throughput, config advanced 802.11b profile utilization
show advanced 802.11a receiver
To display the configuration and statistics of the 802.11a receiver, use the show advanced 802.11a receiver command.
show advanced 802.11a receiver
Syntax Description
show
Display configurations.
advanced
Advanced parameters.
802.11a
802.11a network.
receiver
Receiver.
Defaults
None.
Examples
> show advanced 802.11a receiver802.11a Advanced Receiver SettingsRxStart : Signal Threshold........................... 15RxStart : Signal Lamp Threshold...................... 5RxStart : Preamble Power Threshold................... 2RxReStart : Signal Jump Status......................... EnabledRxReStart : Signal Jump Threshold...................... 10TxStomp : Low RSSI Status.............................. EnabledTxStomp : Low RSSI Threshold........................... 30TxStomp : Wrong BSSID Status........................... EnabledTxStomp : Wrong BSSID Data Only Status................. EnabledRxAbort : Raw Power Drop Status........................ DisabledRxAbort : Raw Power Drop Threshold..................... 10RxAbort : Low RSSI Status.............................. DisabledRxAbort : Low RSSI Threshold........................... 0RxAbort : Wrong BSSID Status........................... DisabledRxAbort : Wrong BSSID Data Only Status................. DisabledRelated Commands
config advanced 802.11a monitor coverage, config advanced 802.11a monitor load, config advanced 802.11a monitor noise, config advanced 802.11a monitor signal
show advanced 802.11a summary
To display the advanced 802.11a Cisco 1000 series lightweight access point name, channel, and transmit level summary, use the show advanced 802.11a summary command.
show advanced 802.11a summary
Syntax Description
show
Display configurations.
advanced
Advanced parameters.
802.11a
802.11a network.
summary
Cisco 1000 series lightweight access point name, channel, and transmit level summary.
Defaults
None.
Examples
> show advanced 802.11a summaryAP Name Channel TxPower Level-------------------------------- ----------- -------------AP03 36* 1*AP02 52 5*AP01 64 5
Note
Related Commands
show advanced 802.11b summary
show advanced 802.11a txpower
To view the advanced 802.11a automatic transmit power assignment, use the show advanced 802.11a txpower command.
show advanced 802.11a txpower
Syntax Description
show
Display configurations.
advanced
Advanced parameters.
802.11a
802.11a network.
txpower
Transmit power.
Defaults
None.
Examples
> show advanced 802.11a txpowerAutomatic Transmit Power AssignmentTransmit Power Assignment Mode.................. AUTOTransmit Power Update Interval.................. 600 secondsTransmit Power Threshold........................ -65 dBmTransmit Power Neighbor Count................... 3 APsTransmit Power Update Contribution.............. SN.Transmit Power Assignment Leader................ xx:xx:xx:xx:xx:xxLast Run........................................ 384 seconds agoRelated Commands
config advanced 802.11a txpower-update, config 802.11a txPower
SHOW ADVANCED 802.11B COMMANDS
Use the SHOW ADVANCED 802.11b commands show advanced 802.11b parameters.
show advanced 802.11b channel
To display the automatic channel assignment status and statistics, use the show advanced 802.11b channel command.
show advanced 802.11b channel
Syntax Description
show
Display configurations.
advanced
Advanced parameters.
802.11b
802.11b/g network.
channel
Channel status.
Defaults
None.
Examples
> show advanced 802.11b channelAutomatic Channel AssignmentChannel Assignment Mode........................ OFFChannel Update Interval........................ 600 secondsChannel Update Contribution.................... SNI.Channel Assignment Leader...................... xx:xx:xx:xx:xx:xxLast Run....................................... 157 seconds agoChannel Energy LevelsMinimum...................................... unknownAverage...................................... unknownMaximum...................................... unknownChannel Dwell TimesMinimum...................................... unknownAverage...................................... unknownMaximum...................................... unknownRelated Commands
config 802.11b channel
show advanced 802.11b group
To display the advanced 802.11b/g Cisco radio RF grouping, use the show advanced 802.11b group command.
show advanced 802.11b group
Syntax Description
show
Display configurations.
advanced
Advanced parameters.
802.11b
802.11b/g network.
group
RF grouping values.
Defaults
None.
Examples
> show advanced 802.11b groupRadio RF Grouping802.11b Group Mode.............................. AUTO802.11b Group Update Interval................... 600 seconds802.11b Group Leader............................ xx:xx:xx:xx:xx:xx802.11b Group Member.......................... xx:xx:xx:xx:xx:xx802.11b Last Run................................ 511 seconds agoRelated Commands
config advanced 802.11b group-mode
show advanced 802.11b logging
To display advanced 802.11b/g RF event and performance logging, use the show advanced 802.11b logging command.
show advanced 802.11b logging
Syntax Description
show
Display configurations.
advanced
Advanced parameters.
802.11b
802.11b network.
logging
RF event and performance logging.
Defaults
None.
Examples
> show advanced 802.11b loggingRF Event and Performance LoggingChannel Update Logging........................... OffCoverage Profile Logging......................... OffForeign Profile Logging.......................... OffLoad Profile Logging............................. OffNoise Profile Logging............................ OffPerformance Profile Logging...................... OffTransmit Power Update Logging.................... OffRelated Commands
config advanced 802.11b logging channel, config advanced 802.11b logging coverage, config advanced 802.11b logging foreign, config advanced 802.11b logging load, config advanced 802.11b logging noise, config advanced 802.11b logging performance, config advanced 802.11b logging power
show advanced 802.11b monitor
To display the advanced 802.11b/g default Cisco radio monitoring, use the show advanced 802.11b monitor command.
show advanced 802.11b monitor
Syntax Description
show
Display configurations.
advanced
Advanced parameters.
802.11b
802.11b/g network.
monitor
Cisco radio monitoring values.
Defaults
None.
Examples
> show advanced 802.11b monitorDefault 802.11b AP monitoring802.11b Monitor Mode......................... enable802.11b Monitor Channels..................... Country channels802.11b AP Coverage Interval................. 180 seconds802.11b AP Load Interval..................... 60 seconds802.11b AP Noise Interval.................... 180 seconds802.11b AP Signal Strength Interval.......... 60 secondsRelated Commands
config advanced 802.11b monitor coverage, config advanced 802.11b monitor load, config advanced 802.11b monitor noise, config advanced 802.11b monitor signal
show advanced 802.11b profile
To display the advanced 802.11b/g Cisco radio performance profiles, use the show advanced 802.11b profile command.
show advanced 802.11b profile {global | Cisco_AP}
Syntax Description
Defaults
None.
Examples
> show advanced 802.11b profile globalDefault 802.11b AP performance profiles802.11b Global Interference threshold.............. 10%802.11b Global noise threshold..................... -70 dBm802.11b Global RF utilization threshold............ 80%802.11b Global throughput threshold................ 1000000 bps802.11b Global clients threshold................... 12 clients802.11b Global coverage threshold.................. 12 dB802.11b Global coverage exception level............ 80%802.11b Global client minimum exception lev........ 3 clients> show advanced 802.11b profile AP1Cisco 1000 series lightweight access point performance profile not customizedThis response indicates that the performance profile for this Cisco 1000 series lightweight access point is using the global defaults and has not been individually configured.
Related Commands
config advanced 802.11b profile clients, config advanced 802.11b profile coverage, config advanced 802.11b profile customize, config advanced 802.11b profile exception, config advanced 802.11b profile foreign, config advanced 802.11b profile level, config advanced 802.11b profile noise, config advanced 802.11b profile throughput, config advanced 802.11b profile utilization
show advanced 802.11b receiver
To display the advanced 802.11b/g default Cisco radio receiver parameters, use the show advanced 802.11b receiver command.
show advanced 802.11b receiver
Syntax Description
show
Display configurations.
advanced
Advanced parameters.
802.11b
802.11b/g network.
receiver
Cisco radio receiver values.
Defaults
None.
Examples
> show advanced 802.11b receiverDefault 802.11b Receiver SettingsRxStart : Signal Threshold............... 15RxStart : Signal Jump Threshold.......... 5RxStart : Preamble Power Threshold....... 2RxRestart : Signal Jump Status............. EnabledRxRestart : Signal Jump Threshold.......... 10TxStomp : Low RSS Status. .............. DisabledTxStomp : Low RSSI Threshold............. 37TxStomp : Wrong BSSID Status............. DisabledTxStomp : Wrong BSSID Data Only Status... DisabledRxAbort : Raw Power Drop Status.......... DisabledRxAbort : Raw Power Drop Threshold....... 0RxAbort : Low RSSI Status................ EnabledRxAbort : Low RSSI Threshold............. 0RxAbort : Wrong BSSID Status............. DisabledRxAbort : Wrong BSSID Data Only Status... DisabledRelated Commands
config advanced 802.11b monitor coverage, config advanced 802.11b monitor load, config advanced 802.11b monitor noise, config advanced 802.11b monitor signal
show advanced 802.11b summary
To display the advanced 802.11b/g Cisco 1000 series lightweight access point name, channel, and transmit level summary, use the show advanced 802.11b summary command.
show advanced 802.11b summary
Syntax Description
show
Display configurations.
advanced
Advanced parameters.
802.11b
802.11b/g network.
summary
Cisco 1000 series lightweight access point name, channel, and transmit level summary.
Defaults
None.
Examples
> show advanced 802.11b summaryAP name Channel Txpower Level------------------- ---------- ------------AP1 11* 1*AP2 10* 4AP3 6* 2
Note
Related Commands
show advanced 802.11a summary
show advanced 802.11b txpower
To view the advanced 802.11b/g automatic transmit power assignment, use the show advanced 802.11b txpower command.
show advanced 802.11b txpower
Syntax Description
show
Display configurations.
advanced
Advanced parameters.
802.11b
802.11b/g network.
txpower
Transmit power.
Defaults
None.
Examples
> show advanced 802.11b txpowerAutomatic Transmit Power AssignmentTransmit Power Assignment Mode................. AUTOTransmit Power Update Interval................. 600 secondsTransmit Power Threshold....................... -65 dBmTransmit Power Neighbor Count.................. 3 APsTransmit Power Update Contribution............. SNI.Transmit Power Assignment Leader............... xx:xx:xx:xx:xx:xxLast Run....................................... 427 seconds agoRelated Commands
config 802.11b txPower
show advanced client-handoff
To display the number of automatic client handoffs after retries, use the show advanced client-handoff command.
show advanced client-handoff
Syntax Description
show
Display configurations.
advanced
Advanced parameters.
client-handoff
Advanced client handoff count.
Defaults
None.
Examples
> show advanced client-handoffClient auto handoff after retries................ 130Related Commands
config advanced timers auth-timeout, config advanced timers rogue-ap
show advanced eap
To displayadvanced Extensible Authentication Potocol settings, use the show advanced eap command.
show advanced eap
Syntax Description
Defaults
None.
Examples
> show advanced eapEAP-Identity-Request Timeout (seconds)........... 1EAP-Identity-Request Max Retries................. 20EAP Key-Index for Dynamic WEP.................... 0EAP-Request Timeout (seconds).................... 1EAP-Request Max Retries.......................... 2Related Commands
(tbd)
show advanced max-1x-sessions
To display the maximum number of simultaneous 802.1x sessions allowed per access point, use the show advanced max-1x-sessions command.
show advanced max-1x-sessions
Syntax Description
show
Display configurations.
advanced
Advanced parameters.
max-1x-sessions
Maximum number of simultaneous 802.1x sessions allowed per access point.
Defaults
None.
Examples
> show advanced max-1x-sessionsMax 802.1x session per AP at a given time........ 0Related Commands
(tbd)
show advanced probe-limit
To display the number of probes sent to the WLAN controller per access point per client and the probe interval in milliseconds, use the show advanced probe-limit command.
show advanced probe-limit
Syntax Description
show
Display configurations.
advanced
Advanced parameters.
probe-limit
Number of probes sent to the WLAN controller per access point per client and the probe interval in milliseconds.
Defaults
None.
Examples
> show advanced probe-limitProbes sent to switch per AP slot per client .... 2Probe interval in msec........................... 500Related Commands
(tbd)
show advanced rate
To display whether control path rate limiting is enabled or disabled, use the show advanced rate command.
show advanced rate
Syntax Description
show
Display configurations.
advanced
Advanced parameters.
rate
Control path rate limiting enabled or disabled.
Defaults
None.
Examples
> show advanced rateControl Path Rate Limiting....................... DisabledRelated Commands
(tbd)
show advanced send-disassoc-on-handoff
To display whether the WLAN controller disassociates clients after a handoff, use the show advanced send-disassoc-on-handoff command.
show advanced send-disassoc-on-handoff
Syntax Description
show
Display configurations.
advanced
Advanced parameters.
send-disassoc-on-handoff
WLAN controller disassociates clients after a handoff enabled or disabled.
Defaults
None.
Examples
> show advanced send-disassoc-on-handoffSend Disassociate on Handoff..................... DisabledRelated Commands
(tbd)
show advanced statistics
To display whether or not the Cisco Wireless LAN controller port statistics are enabled or disabled, use the show advanced statistics command.
show advanced statistics
Syntax Description
show
Display configurations.
advanced
Advanced parameters.
statistics
Show Cisco Wireless LAN controller port statistics state.
Defaults
None.
Examples
> show advanced statisticsSwitch port statistics........................... EnabledRelated Commands
config advanced timers auth-timeout, config advanced timers rogue-ap
show advanced timers
To display the advanced mobility anchor, authentication response, and rogue access point entry timers, use the show advanced timers command.
show advanced timers
Syntax Description
Defaults
Shown below in examples.
Examples
> show advanced timersAuthentication Response Timeout (seconds)...... 10Rogue Entry Timeout (seconds).................. 1200AP Heart Beat Timeout (seconds)................ 30AP Discovery Timeout (seconds)................. 10EAP Request Timeout (seconds).................. 8 (only when EAP is enabled)Related Commands
config advanced timers auth-timeout, config advanced timers rogue-ap
SHOW AP COMMANDS
Use the SHOW AP commands to show access point parameters.
show ap auto-rf
To display the auto-rf settings for a Cisco 1000 series lightweight access point, use the show ap auto-rf command.
show ap auto-rf {802.11a | 802.11b} Cisco_AP
Syntax Description
show
Display configurations.
ap auto-rf
Cisco radio.
{802.11a | 802.11b}
802.11a or 802.11b/g setting.
Cisco_AP
Cisco 1000 series lightweight access point name.
Defaults
None.
Examples
> show ap auto-rf 802.11a AP1Number Of Slots.................................. 2Rad Name......................................... AP03MAC Address...................................... 00:0b:85:01:18:b7Radio Type..................................... RADIO_TYPE_80211aNoise InformationNoise Profile................................ PASSEDChannel 36................................... -88 dBmChannel 40................................... -86 dBmChannel 44................................... -87 dBmChannel 48................................... -85 dBmChannel 52................................... -84 dBmChannel 56................................... -83 dBmChannel 60................................... -84 dBmChannel 64................................... -85 dBmInterference InformationInterference Profile......................... PASSEDChannel 36................................... -66 dBm @ 1% busyChannel 40................................... -128 dBm @ 0% busyChannel 44................................... -128 dBm @ 0% busyChannel 48................................... -128 dBm @ 0% busyChannel 52................................... -128 dBm @ 0% busyChannel 56................................... -73 dBm @ 1% busyChannel 60................................... -55 dBm @ 1% busyChannel 64................................... -69 dBm @ 1% busyLoad InformationLoad Profile................................. PASSEDReceive Utilization.......................... 0%Transmit Utilization......................... 0%Channel Utilization.......................... 1%Attached Clients............................. 1 clientsCoverage InformationCoverage Profile............................. PASSEDFailed Clients............................... 0 clientsClient Signal StrengthsRSSI -100 dBm................................ 0 clientsRSSI -92 dBm................................ 0 clientsRSSI -84 dBm................................ 0 clientsRSSI -76 dBm................................ 0 clientsRSSI -68 dBm................................ 0 clientsRSSI -60 dBm................................ 0 clientsRSSI -52 dBm................................ 0 clientsClient Signal To Noise RatiosSNR 0 dBm................................. 0 clientsSNR 5 dBm................................. 0 clientsSNR 10 dBm................................. 0 clientsSNR 15 dBm................................. 0 clientsSNR 20 dBm................................. 0 clientsSNR 25 dBm................................. 0 clientsSNR 30 dBm................................. 0 clientsSNR 35 dBm................................. 0 clientsSNR 40 dBm................................. 0 clientsSNR 45 dBm................................. 0 clientsNearby RADsRAD 00:0b:85:01:05:08 slot 0................. -46 dBm on 10.1.30.170RAD 00:0b:85:01:12:65 slot 0................. -24 dBm on 10.1.30.170Channel Assignment InformationCurrent Channel Average Energy............... -86 dBmPrevious Channel Average Energy.............. -75 dBmChannel Change Count......................... 109Last Channel Change Time..................... Wed Sep 29 12:53e:34 2004Recommended Best Channel..................... 44RF Parameter RecommendationsPower Level.................................. 1RTS/CTS Threshold............................ 2347Fragmentation Threshold...................... 2346Antenna Pattern.............................. 0Related Commands
config 802.11a antenna, config 802.11b antenna, config cell
show ap bmode
To display the backhaul mode for a Cisco 1030 or 1500 Series lightweight access point deployed in bridging or mesh mode, use the show ap bhmode command.
show ap bhmode Cisco_AP
Syntax Description
Defaults
None.
Examples
> show ap bhmode AP02Related Commands
config ap stats-timer
show ap bhrate
To display the backhaul rate for a Cisco 1030 or 1500 Series lightweight access point deployed in bridging or mesh mode, use the show ap bhrate command.
show ap bhrate Cisco_AP
Syntax Description
Defaults
None.
Examples
> show ap bhrate AP02Related Commands
config ap stats-timer
show ap config
To display the detailed configuration for an 802.11b/g Cisco 1000 series lightweight access point, use the show ap config command.
show ap config {802.11a | 802.11b | general} Cisco_AP
Syntax Description
show
Display configurations.
ap config
Cisco radio.
802.11a
802.11a settings.
802.11b
802.11b/g settings.
general
General settings.
Cisco_AP
Cisco 1000 series lightweight access point name.
Defaults
None.
Examples
> show ap config 802.11a AP02Cisco AP Identifier.............................. 0Cisco AP Name.................................... AP02AP Regulatory Domain............................. UnconfiguredSwitch Port Number .............................. 1MAC Address...................................... 00:0b:85:18:b6:50IP Address Configuration......................... DHCPIP Address....................................... 1.100.49.240IP NetMask....................................... 255.255.255.0Gateway IP Addr.................................. 1.100.49.1Cisco AP Location................................ default-locationCisco AP Group Name.............................. default-groupPrimary Cisco Switch............................. Cisco_32:ab:63Secondary Cisco Switch...........................Tertiary Cisco Switch............................Administrative State ............................ ADMIN_ENABLEDOperation State ................................. REGISTEREDMirroring Mode .................................. DisabledAP Mode ......................................... LocalRemote AP Debug ................................. DisabledS/W Version .................................... 3.1.61.0Boot Version ................................... 1.2.59.6Stats Re--More-- or (q)uitporting Period .................................. 180LED State........................................ EnabledILP Pre Standard Switch.......................... DisabledILP Power Injector............................... DisabledNumber Of Slots.................................. 2AP Model......................................... AS-1200AP Serial Number................................. 044110223AAP Certificate Type.............................. Manufacture InstalledAttributes for Slot 0Radio Type................................... RADIO_TYPE_80211aAdministrative State ........................ ADMIN_ENABLEDOperation State ............................. UPWLAN Override................................ DisabledCellId ...................................... 0Station ConfigurationConfiguration ............................. AUTOMATICNumber Of WLANs ........................... 1Medium Occupancy Limit .................... 100CFP Period ................................ 4CFP MaxDuration ........................... 60BSSID ..................................... 00:0b:85:18:b6:50Operation Rate Set6000 Kilo Bits........................... MANDATORY9000 Kilo Bits........................... SUPPORTED12000 Kilo Bits.......................... MANDATORY18000 Kilo Bits.......................... SUPPORTED24000 Kilo Bits.......................... MANDATORY36000 Kilo Bits.......................... SUPPORTED48000 Kilo Bits.......................... SUPPORTED54000 Kilo Bits.......................... SUPPORTEDBeacon Period ............................. 100DTIM Period ............................... 1Fragmentation Threshold ................... 2346Multi Domain Capability Implemented ....... TRUEMulti Domain Capability Enabled ........... TRUECountry String ............................ USMulti Domain CapabilityConfiguration ............................. AUTOMATICFirst Chan Num ............................ 36Number Of Channels ........................ 4MAC Operation ParametersConfiguration ............................. AUTOMATICRTS Threshold ............................. 2347Short Retry Limit ......................... 7Long Retry Limit .......................... 4Fragmentation Threshold ................... 2346Maximum Tx MSDU Life Time ................. 512Maximum Rx Life Time ...................... 512Tx PowerNum Of Supported Power Levels ............. 5Tx Power Level 1 .......................... 18 dBmTx Power Level 2 .......................... 15 dBmTx Power Level 3........................... 12 dBmTx Power Level 4 .......................... 9 dBmTx Power Level 5 .......................... 6 dBmTx Power Configuration .................... CUSTOMIZEDCurrent Tx Power Level..................... 5Phy OFDM parametersConfiguration ............................. AUTOMATICCurrent Channel ........................... 36TI Threshold .............................. -50Antenna Type............................... INTERNAL_ANTENNAInternal Antenna Gain (in .5 dBm units).... 11AntennaMode................................ ANTENNA_OMNIPerformance Profile ParametersConfiguration ............................. AUTOMATICInterference threshold..................... 10%Noise threshold............................ -70 dBmRF utilization threshold................... 80%Data-rate threshold........................ 1000000 bpsClient threshold........................... 12 clientsCoverage SNR threshold..................... 16 dBCoverage exception level................... 25%Client minimum exception level............. 3 clientsRogue Containment InformationContainment Count............................ 0> show ap config 802.11b AP02Cisco AP Identifier.............................. 0Cisco AP Name.................................... AP02AP Regulatory Domain............................. UnconfiguredSwitch Port Number .............................. 1MAC Address...................................... 00:0b:85:18:b6:50IP Address Configuration......................... DHCPIP Address....................................... 1.100.49.240IP NetMask....................................... 255.255.255.0Gateway IP Addr.................................. 1.100.49.1Cisco AP Location................................ default-locationCisco AP Group Name.............................. default-groupPrimary Cisco Switch............................. Cisco_32:ab:63Secondary Cisco Switch...........................Tertiary Cisco Switch............................Administrative State ............................ ADMIN_ENABLEDOperation State ................................. REGISTEREDMirroring Mode .................................. DisabledAP Mode ......................................... LocalRemote AP Debug ................................. DisabledS/W Version .................................... 3.1.61.0Boot Version ................................... 1.2.59.6Stats Reporting Period .......................... 180LED State........................................ EnabledILP Pre Standard Switch.......................... DisabledILP Power Injector............................... DisabledNumber Of Slots.................................. 2AP Model......................................... AS-1200AP Serial Number................................. 044110223AAP Certificate Type.............................. Manufacture InstalledAttributes for Slot 1Radio Type................................... RADIO_TYPE_80211gAdministrative State ........................ ADMIN_ENABLEDOperation State ............................. UPWLAN Override ............................... DisabledCellId ...................................... 0Station ConfigurationConfiguration ............................. AUTOMATICNumber Of WLANs ........................... 1Medium Occupancy Limit .................... 100CFP Period ................................ 4CFP MaxDuration ........................... 60BSSID ..................................... 00:0b:85:18:b6:50Operation Rate Set1000 Kilo Bits........................... MANDATORY2000 Kilo Bits........................... MANDATORY5500 Kilo Bits........................... MANDATORY11000 Kilo Bits.......................... MANDATORY6000 Kilo Bits........................... SUPPORTED9000 Kilo Bits........................... SUPPORTED12000 Kilo Bits.......................... SUPPORTED18000 Kilo Bits.......................... SUPPORTED24000 Kilo Bits.......................... SUPPORTED36000 Kilo Bits.......................... SUPPORTED48000 Kilo Bits.......................... SUPPORTED54000 Kilo Bits.......................... SUPPORTEDBeacon Period ............................. 100DTIM Period ............................... 1Fragmentation Threshold ................... 2346Multi Domain Capability Implemented ....... TRUEMulti Domain Capability Enabled ........... TRUECountry String ............................ USMulti Domain CapabilityConfiguration ............................. AUTOMATICFirst Chan Num ............................ 1Number Of Channels ........................ 11MAC Operation ParametersConfiguration ............................. AUTOMATICRTS Threshold ............................. 2347Short Retry Limit ......................... 7Long Retry Limit .......................... 4Fragmentation Threshold ................... 2346Maximum Tx MSDU Life Time ................. 512Maximum Rx Life Time....................... 512Tx PowerNum Of Supported Power Levels.............. 5Tx Power Level 1 .......................... 17 dBmTx Power Level 2........................... 14 dBmTx Power Level 3........................... 11 dBmTx Power Level 4........................... 8 dBmTx Power Level 5........................... 5 dBmTx Power Configuration..................... CUSTOMIZEDCurrent Tx Power Level..................... 5Phy OFDM parametersConfiguration.............................. CUSTOMIZEDCurrent Channel............................ 1TI Threshold............................... -50Antenna Type............................... INTERNAL_ANTENNAInternal Antenna Gain (in5 dBm units)...... 11Diversity.................................. DIVERSITY_ENABLEDPerformance Profile ParametersConfiguration.............................. AUTOMATICInterference threshold..................... 10%Noise threshold............................ -70 dBmRF utilization threshold................... 80%Data-rate threshold........................ 1000000 bpsClient threshold........................... 12 clientsCoverage SNR threshold..................... 12 dBCoverage exception level................... 25%Client minimum exception level............. 3 clientsRogue Containment InformationContainment Count............................ 0> show ap config general AP02Cisco AP Identifier.............................. 0Cisco AP Name.................................... AP02AP Regulatory Domain............................. UnconfiguredSwitch Port Number............................... 1MAC Address...................................... xx:xx:xx:xx:xx:xxIP Address Configuration......................... DHCPIP Address....................................... 1.100.49.240IP NetMask....................................... 255.255.255.0Gateway IP Addr.................................. 1.100.49.1Cisco AP Location................................ default-locationCisco AP Group Name.............................. default-groupPrimary Cisco Switch............................. Cisco_32:ab:63Secondary Cisco Switch...........................Tertiary Cisco Switch............................Administrative State............................. ADMIN_ENABLEDOperation State.................................. REGISTEREDMirroring Mode................................... DisabledAP Mode.......................................... LocalRemote AP Debug.................................. DisabledS/W Version..................................... 3.1.61.0Boot Version.................................... 1.2.59.6porting Period................................... 180LED State........................................ EnabledILP Pre Standard Switch.......................... DisabledILP Power Injector............................... DisabledNumber Of Slots.................................. 2AP Model......................................... AS-1200AP Serial Number................................. 044110223AAP Certificate Type.............................. Manufacture InstalledRelated Commands
config 802.11a antenna, config 802.11b antenna, config cell
show ap core-dump
To display the memory core dump setting for a Cisco 1000 series lightweight access point, use the show ap core-dump command.
show ap core-dump Cisco_AP
Syntax Description
show
Display configurations.
ap
Cisco radio.
core-dump
Display the memory core dump setting for an access point.
Cisco_AP
Cisco 1000 series lightweight access point name.
Defaults
None.
Examples
> show ap core-dump AP02Related Commands
config ap stats-timer
show ap crash-file
To display the list of both crash and radio core dump files generated by Cisco 1000 series lightweight access points, use the show ap crash-file command.
show ap crash-file
Syntax Description
show
Display configurations.
ap
Cisco radio.
crash-file
Display the list of both crash and radio core dump files generated by access points. The generated information includes size and memory usage.
Defaults
None.
Examples
> show ap crash-fileRelated Commands
config ap stats-timer
show ap stats
To display the statistics for a Cisco 1000 series lightweight access point, use the show ap stats command.
show ap stats {802.11a | 802.11b} Cisco_AP
Syntax Description
show
Display configurations.
ap stats
Cisco radio.
802.11a
802.11a statistics.
802.11b
802.11b/g statistics.
Cisco_AP
Cisco 1000 series lightweight access point name.
Defaults
None.
Examples
> show ap stats 802.11b AP02Number Of Slots.................................. 2AP Name.......................................... AP02MAC Address...................................... 00:0b:85:18:b6:50Radio Type..................................... RADIO_TYPE_80211aStats InformationNumber of Users.............................. 0TxFragmentCount.............................. 1679MulticastTxFrameCnt.......................... 1260FailedCount.................................. 15892RetryCount................................... 331MultipleRetryCount........................... 0FrameDuplicateCount.......................... 0RtsSuccessCount.............................. 0RtsFailureCount.............................. 0AckFailureCount.............................. 80212RxFragmentCount.............................. 248671MulticastRxFrameCnt.......................... 0FcsErrorCount................................ 105968TxFrameCount................................. 1679WepUndecryptableCount........................ 0Related Commands
config ap stats-timer
show ap summary
To display a summary of all Cisco 1000 series lightweight access points attached to the Cisco Wireless LAN controller, use the show ap summary command. A list containing each Cisco 1000 series lightweight access point name, number of slots, manufacturer, MAC address, location and Cisco Wireless LAN controller port number is displayed.
show ap summary
Syntax Description
show
Display configurations.
ap
All Cisco 1000 series lightweight access points.
summary
Summary of all Cisco 1000 series lightweight access points.
Defaults
None.
Examples
> show ap summaryAP Name Slots AP Model EnetMAC Location Port------------------ ----- ------------------- ----------------- ---------------- ----- AP01 2 AIR-AP1210 xx:xx:xx:xx:xx:xx default location 12AP02 2 AIR-AP1210 xx:xx:xx:xx:xx:xx default location 11Related Commands
show advanced 802.11a summary, show advanced 802.11b summary, show certificate summary, show client summary, show mobility summary, show radius summary, show rogue-ap summary, show wlan summary
show ap wlan
To display whether or not a Cisco Wireless LAN controller radio is in wireless LAN override mode (as described in the related product guide), use the show ap wlan command.
show ap wlan {802.11a | 802.11b} Cisco_AP
Syntax Description
Defaults
None.
Examples
> show ap wlan 802.11a AP01Cisco AP is not in override mode.Related Commands
show advanced 802.11a summary, show advanced 802.11b summary, show certificate summary, show client summary, show mobility summary, show radius summary, show rogue-ap summary, show wlan summary
show arp switch
To display the Cisco Wireless LAN controller MAC addresses, IP Addresses, and port types, use the show arp switch command.
show arp switch
Syntax Description
show
Display configurations.
arp
arp MAC addresses, IP Addresses, and port types.
switch
Cisco Wireless LAN controller parameters.
Defaults
None.
Examples
> show arp switchMAC Address IP Address Port VLAN Type------------------- ---------------- ------------ ---- -------------------xx:xx:xx:xx:xx:xx xxx.xxx.xxx.xxx service port 1xx:xx:xx:xx:xx:xx xxx.xxx.xxx.xxx service portxx:xx:xx:xx:xx:xx xxx.xxx.xxx.xxx service portRelated Commands
debug arp
show auth-list
To display the access point authorization list, use the show auth-list command.
show auth-list
Syntax Description
Defaults
None.
Examples
> show auth-listAuthorize APs against AAA...................... disabledAllow APs with Self-signed Certificate (SSC)... disabledMac Addr Cert Type Key Hash----------------------- ---------- ------------------------------------------xx:xx:xx:xx:xx:xx MICRelated Commands
config auth-list
show boot
Each Cisco Wireless LAN controller retains one primary and one backup operating system software load in non-volatile RAM. This allows operators to have the Cisco Wireless LAN controllers boot off the primary load (default), or revert to the backup load when desired. To display the primary and backup software build numbers with an indication of which is active, use the show boot command.
show boot
Syntax Description
Defaults
None.
Examples
> show bootPrimary Boot Image............................... 3.2.13.0 (active)Backup Boot Image................................ 3.2.15.0Related Commands
config exclusionlist add, config exclusionlist delete, config exclusionlist description, show client
SHOW CERTIFICATE COMMANDS
Use the SHOW CERTIFICATE commands to display certificate settings.
show certificate compatibility
To display whether or not certificates are verified as compatible in the Cisco Wireless LAN controller, use the show certificate compatibility command.
show certificate compatibility
Syntax Description
show
Display configurations.
certificate
All certificates.
compatibility
Compatibility of certificates.
Defaults
None.
Examples
> show certificate compatibilityCertificate compatibility mode:................ offRelated Commands
show certificate summary
show certificate summary
To display a summary of all certificates active in the Cisco Wireless LAN controller, use the show certificate summary command.
show certificate summary
Syntax Description
Defaults
None.
Examples
> show certificate summaryWeb Administration Certificate................. Locally GeneratedWeb Authentication Certificate................. Locally GeneratedCertificate compatibility mode:................ offRelated Commands
show certificate compatibility
SHOW CLIENT COMMANDS
Use the SHOW CLIENT commands to display client settings.
show client ap
To display the clients on a Cisco 1000 series lightweight access point, use the show client ap command.
Note
show client ap {802.11a | 802.11b} Cisco_AP
Syntax Description
show
Display configurations.
client ap
Cisco radio.
802.11a
802.11a clients.
802.11b
802.11b/g clients.
Cisco_AP
Cisco 1000 series lightweight access point name.
Defaults
None.
Examples
> show client ap 802.11b AP1MAC Address AP Id Status WLAN Id Authenticated----------------- ------ ------------- --------- -------------xx:xx:xx:xx:xx:xx 1 Associated 1 NoRelated Commands
show client detail, show client summary, show client username, show exclusionlist
show client detail
To display detailed information for a client on a Cisco 1000 series lightweight access point, use the show client detail command.
Note
show client detail MAC
Syntax Description
show
Display configurations.
client
802.11a or 802.11b/g client.
detail
Connectivity information.
MAC
MAC address of the specific client.
Defaults
None.
Examples
> show client detail 00:0c:41:07:33:a6Client MAC Address............................... xx:xx:xx:xx:xx:xxClient Username.................................. N/AAP MAC Address................................... xx:xx:xx:xx:xx:xxClient State..................................... AssociatedWireless LAN Id.................................. 1IP Address....................................... UnknownAssociation Id................................... 1Authentication Algorithm......................... Shared KeyReason Code...................................... 0Status Code...................................... 0Session Timeout.................................. 0Mirroring........................................ DisabledQoS Level........................................ GoldDiff Serv Code Point (DSPC)...................... disabled802.1P Priority Tag.............................. disabledMobility State................................... LocalMobility Move Count.............................. 0Security Policy Completed........................ NoPolicy Manager State............................. DHCP_REQDPolicy Manager Rule Created...................... NoNPU Fast Notified................................ YesPolicy Type...................................... N/AEncryption Cipher................................ WEP (104 bits)EAP Type......................................... UnknownInterface........................................ managementVLAN............................................. 0Client Capabilities:CF Pollable................................ Not implementedCF Poll Request............................ Not implementedShort Preamble............................. Not implementedPBCC....................................... Not implementedChannel Agility............................ Not implementedListen Interval............................ 0Client Statistics:Number of Bytes Received................... 0Number of Bytes Sent....................... 0Number of Packets Received................. 0Number of Packets Sent..................... 0Number of Policy Errors.................... 0Radio Signal Strength Indicator............ UnavailableSignal to Noise Ratio...................... UnavailableNearby AP Statistics:AP03(slot 0) 24643 seconds ago............. -11 dBmRelated Commands
show client ap, show client summary, show client username, show exclusionlist
show client summary
To display a summary of clients associated with a Cisco 1000 series lightweight access point, use the show client summary command.
Note
show client summary
Syntax Description
Defaults
None.
Examples
> show client summaryNumber of Clients................................ 24MAC Address AP Name Status WLAN Auth Protocol Port----------------- ----------------- ------------- ---- ---- -------- ----xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11a 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11a 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11b 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11a 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11b 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11b 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11b 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11b 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11b 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11a 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11a 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11b 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11a 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11a 1Related Commands
show client ap, show client detail, show client username, show exclusionlist
show client username
To display client data by username, use the show client username command.
show client username username
Syntax Description
show
Display configurations.
client
Display client data.
username
Cisco radio.
username
Client's username.
Defaults
None.
Examples
> show client username IT_007MAC Address AP ID Status WLAN Id Authenticated----------------- ------ ------------- --------- -------------xx:xx:xx:xx:xx:xx 1 Associated 1 NoRelated Commands
show client ap, show client detail, show client summary
show country
The Cisco Wireless LAN controller must be configured to comply with the target country's permitted 802.11a and/or 802.11b frequency bands. To display a list of supported countries and their permitted frequency bands, use the show country command. This command also shows you the current country setting for the Cisco Wireless LAN controller.
Note
show country
Syntax Description
Defaults
None.
Examples
> show countryRelated Commands
show sysinfo
show cpu
To display current WLAN Controller CPU usage information, use the show cpu command.
show cpu
Syntax Description
Defaults
None.
Examples
> show cpuCurrent CPU load: 2.50%Related Commands
show sysinfo
show custom-web
To display web authentication customization information, use the show custom-web command.
show custom-web
Syntax Description
Defaults
None.
Examples
> show custom-webRadius Authentication Method..................... PAPCisco Logo....................................... EnabledCustomLogo....................................... NoneCustom Title..................................... NoneCustom Message................................... NoneCustom Redirect URL.............................. NoneExternal web authentication Mode................. DisabledExternal web authentication URL.................. NoneRelated Commands
config custom-web
show database summary
To display the local database configuration, use the show database command.
show database summary
Syntax Description
Defaults
None.
Examples
> show database summaryCurrent Max database entries.......................... 512Max database entries on next reboot................... 512Related Commands
show sysinfo
show debug
Use the show debug command, to determine if MAC address and other flag debugging is enabled or disabled.
show debug
Syntax Description
Defaults
disabled.
Examples
> show debugMAC debugging............................... disabledDebug Flags Enabled:arp error enabled.bcast error enabled.Related Commands
debug mac
show dhcp
Use the show dhcp command, to display the internal DHCP server configuration.
show dhcp {leases | summary | scope}
Syntax Description
Defaults
None.
Examples
> show dhcp leasesNo leases allocated.> show dhcp summaryScope Name Enabled Address Range003 No 0.0.0.0 -> 0.0.0.0> show dhcp 003Enabled....................................... NoLease Time.................................... 0Pool Start.................................... 0.0.0.0Pool End...................................... 0.0.0.0Network....................................... 0.0.0.0Netmask....................................... 0.0.0.0Default Routers............................... 0.0.0.0 0.0.0.0 0.0.0.0DNS Domain....................................DNS........................................... 0.0.0.0 0.0.0.0 0.0.0.0Netbios Name Servers.......................... 0.0.0.0 0.0.0.0 0.0.0.0Related Commands
config dhcp
show dhcp proxy
Use the show dhcp proxy command to display the status of DHCP proxy handling.
show dhcp proxy
Syntax Description
Defaults
None.
Examples
> show dhcp proxyDHCP Proxy Behaviour: enabledRelated Commands
config dhcp proxy
show eventlog
Use the show eventlog command, to display the event log.
show eventlog
Syntax Description
Defaults
None.
Examples
> show eventlogTimeFile Line TaskID Code d h m sEVENT> bootos.c 788 125CEBCC AAAAAAAA 0 0 0 6EVENT> bootos.c 788 125CEBCC AAAAAAAA 0 0 0 6EVENT> bootos.c 788 125C597C AAAAAAAA 0 0 0 6EVENT> bootos.c 788 125C597C AAAAAAAA 0 0 0 6EVENT> bootos.c 788 125C597C AAAAAAAA 0 0 0 6EVENT> bootos.c 788 125C597C AAAAAAAA 0 0 0 6EVENT> bootos.c 788 125C597C AAAAAAAA 0 0 0 6EVENT> bootos.c 788 125C597C AAAAAAAA 0 0 0 6EVENT> bootos.c 788 1216C36C AAAAAAAA 0 0 0 6EVENT> bootos.c 788 1216C36C AAAAAAAA 0 0 0 6EVENT> bootos.c 788 1216C36C AAAAAAAA 0 0 0 6EVENT> bootos.c 788 1216C36C AAAAAAAA 0 0 0 11Related Commands
show msglog
show exclusionlist
To display a summary of all clients on the manual exclusion list (blacklisted) from associating with this Cisco Wireless LAN controller, use the show exclusionlist command. A list containing each manually Excluded MAC address is displayed.
show exclusionlist
Syntax Description
Defaults
None.
Examples
> show exclusionlistMAC Address Description----------------------- --------------------------------xx:xx:xx:xx:xx:xx Disallowed ClientRelated Commands
config exclusionlist add, config exclusionlist delete, config exclusionlist description, show client
show ike
Use the show ike command to display active IKE SAs.
show ike {brief | IP_or_MAC_address}
Syntax Description
show
Command action.
ike
Display active IKE SAs.
brief
List of all active IKE SAs.
IP_or_MAC_address
IP or MAC address of active IKE SA.
Defaults
None.
Examples
> show ikeRelated Commands
None
show interface
Use the show interface command to display details of the system interfaces.
show interface {summary | detailed interface_name}
Syntax Description
show interface
Command action
summary
Display a summary of the local interfaces.
detailed
Display detailed interface information.
interface_name
Identifies interface name for detailed display
Defaults
None.
Examples
> show interface summaryInterface Name Vlan Id IP Address Type Ap Mgr-------------------------------- -------- --------------- ------- ------ap-manager 149 xxx.xxx.xxx.xxx Static Yesmanagement 149 xxx.xxx.xxx.xxx Static Noservice-port N/A xxx.xxx.xxx.xxx Static Novirtual N/A xxx.xxx.xxx.xxx Static No> show interface detailed managementInterface Name................................... managementMAC Address...................................... 00:0b:85:32:ab:60IP Address....................................... 1.100.49.30IP Netmask....................................... 255.255.255.0IP Gateway....................................... 1.100.49.1VLAN............................................. 149Active Physical Port............................. 1Primary Physical Port............................ 1Backup Physical Port............................. UnconfiguredPrimary DHCP Server.............................. 1.100.2.15Secondary DHCP Server............................ UnconfiguredACL.............................................. UnconfiguredAP Manager....................................... No
Note
Related Commands
config interface
show inventory
To display a physical inventory of the Cisco Wireless LAN controller, use the show inventory command.
show inventory
Syntax Description
Defaults
None.
Examples
> show inventorySwitch Description............................... Cisco ControllerMachine Model.................................... WLC4404-100Serial Number.................................... FLS0923003BBurned-in MAC Address............................ 00:0B:85:32:AB:60Crypto Accelerator 1............................. AbsentCrypto Accelerator 2............................. AbsentPower Supply 1................................... AbsentPower Supply 2................................... Present, OK
Note
Related Commands
show sysinfo
show ipsec
Use the show ipsec command to display active IPSec SAs.
show ipsec {brief | IP_or_MAC_address}
Syntax Description
show
Command action.
ipsec
Display active IPSec SAs
{brief |
IP_or_MAC_address}Enter brief to display active IPSec SAs.
Enter the IP address of MAC address of an IPSec SA.
Defaults
None.
Examples
> show ipsec briefRelated Commands
None
show known ap
To display known Cisco 1000 series lightweight access point information, use the show known ap command.
show known ap {summary | detailed MAC}
Syntax Description
Defaults
None.
Examples
> show known ap summaryMAC Address State # APs # Clients Last Heard----------- ----------- ----- -------- -----------------Related Commands
config ap
show l2tp
To display L2TP sessions, use the show l2tp command.
show l2tp {summary | ip_address}
Syntax Description
show l2tp
Display configurations.
summary
Displays all L2TP sessions.
ip_address
Displays an L2TP session.
Defaults
None.
Examples
> show l2tp summaryLAC_IPaddr LTid LSid RTid RSid ATid ASid State---------- ---- ---- ---- ---- ---- ---- -----Related Commands
None
show load-balancing
To display the status of the load-balancing feature, use the show load-balancing command.
show load-balancing
Syntax Description
Defaults
None.
Examples
> show load-balancingAggressive Load Balancing...................... EnabledAggressive Load Balancing Window............... 0 clientsRelated Commands
config load-balancing
show location summary
To display information about defined locations, use the show location summary command.
show location summary
Syntax Description
show location
Display command for locations.
summary
Display all location information defined in the system.
Defaults
None.
Examples
> show location summaryStatus...................................................... disabledRelated Commands
config location
show loginsession
To display the existing sessions, use the show loginsession command.
show loginsession
Syntax Description
Defaults
None.
Examples
> show loginsessionID User Name Connection From Idle Time Session Time-- --------------- --------------- ------------ ------------00 admin EIA-232 00:00:00 00:19:04Related Commands
config loginsession close
show macfilter
To display the MAC filter parameters, use the show macfilter command. The MAC delimiter (none, colon, or hyphen) for MAC addresses sent to RADIUS servers is displayed. The MAC filter table lists the clients that are always allowed to associate with a wireless LAN.
show macfilter {summary | detail MAC}
Syntax Description
show
Display configurations.
macfilter
Filter details.
summary
Display a summary of all MAC filter entries.
detail MAC
Detailed display of a MAC filter entry.
Defaults
None.
Examples
> show macfilter detail xx:xx:xx:xx:xx:xxMAC Address...................................... xx:xx:xx:xx:xx:xxWLAN Identifier.................................. AnyInterface Name................................... managementDescription...................................... RAP> show macfilter summaryMAC Filter RADIUS Compatibility mode............. Cisco ACSMAC Filter Delimiter............................. NoneLocal Mac Filter TableMAC Address WLAN Id Description----------------------- -------------- --------------------------------xx:xx:xx:xx:xx:xx Any RAPxx:xx:xx:xx:xx:xx Any PAP2 (2nd hop)xx:xx:xx:xx:xx:xx Any PAP1 (1st hop)Related Commands
config macfilter mac-delimiter, config macfilter add, config macfilter delete, config macfilter description, config macfilter ip-address, config macfilter wlan-id, show macfilter.
SHOW MESH COMMANDS
Use the SHOW MESH commands to display mesh settings.
show mesh linkrate
To display the mesh link rate for Cisco 1000 series lightweight access points, use the show mesh linkrate command.
show mesh linkrate <from Cisco_AP> <to Cisco_AP name|MAC address>
Syntax Description
Defaults
None.
Examples
> show mesh linkrateRelated Commands
None.
show mesh neigh
To display the mesh neighbors for a Cisco 1000 series lightweight access point, use the show mesh neigh command.
show mesh neigh Cisco_AP
Syntax Description
show
Display configurations.
mesh
Mesh configuration.
neigh
Show Cisco 1000 series lightweight access point neighborhood list.
Cisco_AP
Cisco 1000 series lightweight access point name.
Defaults
None.
Examples
> show mesh neighRelated Commands
None.
show mesh path
To display the mesh configuration for a Cisco 1000 series lightweight access point, use the show mesh path command.
show mesh path Cisco_AP
Syntax Description
show
Display configurations.
mesh
Mesh configuration.
path
Show Cisco 1000 series lightweight access point path.
Cisco_AP
Cisco 1000 series lightweight access point name.
Defaults
None.
Examples
> show mesh pathRelated Commands
None.
show mesh stats
To display the mesh statistics for a Cisco 1000 series lightweight access point, use the show mesh stats command.
show mesh stats Cisco_AP
Syntax Description
show
Display configurations.
mesh
Mesh configuration.
stats
Show Cisco 1000 series lightweight access point statistics.
Cisco_AP
Cisco 1000 series lightweight access point name.
Defaults
None.
Examples
> show mesh statsRelated Commands
None.
show mesh summary
To display the mesh configuration for a Cisco 1000 series lightweight access pointr, use the show mesh summary command.
show mesh summary Cisco_AP
Syntax Description
show
Display configurations.
summary
Show summary neighbor information for an access point.
Cisco_AP
Cisco 1000 series lightweight access point name.
Defaults
None.
Examples
> show mesh summaryRelated Commands
None.
show mgmtuser
To display the local management user accounts on the Cisco Wireless LAN controller, use the show mgmtuser command.
show mgmtuser
Syntax Description
Defaults
None.
Examples
> show mgmtuserUser Name Permissions Description----------------------- ------------ --------------------------------admin read-writeRelated Commands
config mgmtuser add, config mgmtuser delete, config mgmtuser password
SHOW MOBILITY COMMANDS
Use the SHOW MOBILITY commands to display mobility settings.
show mobility anchor
To display the wireless LAN anchor list for the Cisco Wireless LAN controller mobility groups, use the show mobility anchor command.
show mobility anchor
Syntax Description
show
Display configurations.
mobility
Mobility group.
anchor
Display the mobility wireless LAN anchor list.
Defaults
None.
Examples
> show mobility anchorMobility Anchor Export ListWLAN ID IP AddressRelated Commands
config mobility group discovery, config mobility group member
show mobility statistics
To display the statistics information for the Cisco Wireless LAN controller mobility groups, use the show mobility statistics command.
show mobility statistics
Syntax Description
show
Display configurations.
mobility
Mobility group.
statistics
Displays statistics for the mobility manager.
Defaults
None.
Examples
> show mobility statisticsGlobal Mobility StatisticsRx Errors..................................... 0Tx Errors..................................... 0Responses Retransmitted....................... 0Handoff Requests Received..................... 0Handoff End Requests Received................. 0State Transitions Disallowed.................. 0Resource Unavailable.......................... 0Mobility Initiator StatisticsHandoff Requests Sent......................... 0Handoff Replies Received...................... 0Handoff as Local Received..................... 2Handoff as Foreign Received................... 0Handoff Denys Received........................ 0Anchor Request Sent........................... 0Anchor Deny Received.......................... 0Anchor Grant Received......................... 0Anchor Transfer Received...................... 0Mobility Responder StatisticsHandoff Requests Ignored...................... 0Ping Pong Handoff Requests Dropped............ 0Handoff Requests Dropped...................... 0Handoff Requests Denied....................... 0Client Handoff as Local....................... 0Client Handoff as Foreign ................... 0Client Handoff Inter Group ................... 0Anchor Requests Received...................... 0Anchor Requests Denied........................ 0Anchor Requests Granted....................... 0Anchor Transferred............................ 0Related Commands
config mobility group discovery, config mobility group member
show mobility summary
To display the summary information for the Cisco Wireless LAN controller mobility groups, use the show mobility summary command.
show mobility summary
Syntax Description
show
Display configurations.
mobility
Mobility group.
summary
Display a summary of the mobility manager.
Defaults
None.
Examples
> show mobility summaryMobility Protocol Port........................... 16666Mobility Security Mode........................... DisabledDefault Mobility Domain.......................... mikemeshMobility Group members configured................ 1Switches configured in the Mobility GroupMAC Address IP Address Group Namexx:xx:xx:xx:xx:xx xxx.xxx.xxx.xxx <local>
Note
Related Commands
config mobility group discovery, config mobility group member
show msglog
To display the message logs written to the Cisco Wireless LAN controller database, use the show msglog command. If there are more that 15 entries you are prompted to display the messages shown in the example.
show msglog
Syntax Description
Defaults
None.
Examples
> show msglogMessage Log Severity Level..................... ERRORThu Aug 4 14:30:08 2005 [ERROR] spam_lrad.c 1540: AP 00:0b:85:18:b6:50 associated. Last AP failure was due to Link FailureThu Aug 4 14:30:08 2005 [ERROR] spam_lrad.c 13840: Updating IP info for AP 00:0b:85:18:b6:50 -- static 0, 1.100.49.240/255.255.255.0, gtw 1.100.49.1Thu Aug 4 14:29:32 2005 [ERROR] dhcpd.c 78: dhcp server: binding to 0.0.0.0Thu Aug 4 14:29:32 2005 [ERROR] rrmgroup.c 733: Airewave Director: 802.11a switch group resetThu Aug 4 14:29:32 2005 [ERROR] rrmgroup.c 733: Airewave Director: 802.11bg switch group resetThu Aug 4 14:29:22 2005 [ERROR] sim.c 2841: Unable to get link state for primary port 0 of interface ap-managerThu Aug 4 14:29:22 2005 [ERROR] dtl_l2_dot1q.c 767: Unable to get USPThu Aug 4 14:29:22 2005 Previous message occurred 2 timesThu Aug 4 14:29:14 2005 [CRITICAL] osapi_sem.c 794: Error! osapiMutexTake called with NULL pointer: osapi_bsntime.c:927Thu Aug 4 14:29:14 2005 [CRITICAL] osapi_sem.c 794: Error! osapiMutexTake called with NULL pointer: osapi_bsntime.c:919Thu Aug 4 14:29:14 2005 [CRITICAL] hwutils.c 1861: Security Module not foundThu Aug 4 14:29:13 2005 [CRITICAL] bootos.c 791: Starting code...Related Commands
show eventlog
show nac statistics
To display detailed Network Access Control (NAC) information about a Cisco Wireless LAN controller, use the show nac statistics command.
show nac statistics
Syntax Description
Defaults
None.
Examples
> show nac statisticsServer Index....................................................... 1Server Address..................................................... xxx.xxx.xxx.xxxNumber of requests sent............................................ 0Number of retransmissions.......................................... 0Number of requests received........................................ 0Number of malformed requests received.............................. 0Number of bad auth requests received............................... 0Number of pending requests......................................... 0Number of timed out requests....................................... 0Number of misc dropped request received............................ 0Number of requests sent............................................ 0Related Commands
show nac acl, show nac summary.
show nac summary
To display NAC summary information for a Cisco Wireless LAN controller, use the show nac summary command.
show nac summary
Syntax Description
Defaults
None.
Examples
> show nac summaryNAC ACL Name ...............................................Index Server Address Port State----- ---------------------------------------- ---- -----1 xxx.xxx.xxx.xxx 13336 EnabledRelated Commands
show nac acl, show nac statistics.
show netuser
To display local network user accounts, use the show netuser command.
show netuser
Syntax Description
Defaults
None.
Examples
> show netuserUser Name WLAN Id Description----------------------- -------------- --------------------------------krebbis 1 all krebbisRelated Commands
config netuser add, config netuser delete, config netuser password, config netuser wlan-id
show network
To display the network configuration of the Cisco Wireless LAN controller, use the show network command.
show network
Syntax Description
Defaults
None.
Examples
> show networkRF-Network Name............................. mikemeshWeb Mode.................................... DisableSecure Web Mode............................. EnableSecure Shell (ssh).......................... EnableTelnet...................................... DisableEthernet Multicast Mode..................... DisableUser Idle Timeout........................... 300 secondsARP Idle Timeout............................ 300 secondsARP Unicast Mode............................ DisabledCisco AP Default Master..................... DisableMgmt Via Wireless Interface................. DisableBridge AP Zero Config....................... EnableBridge Shared Secret........................ adminAllow Old Bridging Aps To Authenticate...... EnableOver The Air Provisioning of AP's........... EnableMobile Peer to Peer Blocking................ DisableApple Talk................................ DisableAP Fallback............................... EnableWeb Auth Redirect Ports................... 80Fast SSID Change.......................... DisabledRelated Commands
config network arptimeout, config network bcast-ssid, config network dsport, config network master-base, config network mgmt-via-wireless, config network params, config network rf-mobility-domain, config network secureweb, config network secweb-passwd, config network ssh, config network telnet, config network usertimeout, config network vlan, config network webmode
show pmk-cache
To display information about the PMK cache, use the show port command.
show pmk-cache {all | MAC}
Syntax Description
show
Display configurations.
pmk-cache
PMK cache.
all
Display information about all entries in the PMK cache.
MAC
Display information about a single entry in the PMK cache.
Defaults
None.
Examples
> show pmk-cache xx:xx:xx:xx:xx:xx> show pmk-cache allPMK CacheEntryStation Lifetime VLAN Override IP Override----------------- -------- -------------------- ---------------Related Commands
config pmk-cache delete
show port
To display the Cisco Wireless LAN controller port settings on an individual or global basis, use the show port command.
show port {port | summary}
Syntax Description
show
Display configurations.
port
Cisco Wireless LAN controller port.
{port | summary}
Individual port or all ports.
Defaults
None.
Examples
> show port 1STP Admin Physical Physical Link Link McastPr Type Stat Mode Mode Status Status Trap Appliance POE-- ------- ---- ------- ---------- ---------- ------ ------- --------- -------1 Normal Disa Enable Auto 1000 Full Down Enable Enable N/A
Note
> show port summarySTP Admin Physical Physical Link Link McastPr Type Stat Mode Mode Status Status Trap Appliance POE-- ------- ---- ------- ---------- ---------- ------ ------- --------- -------1 Normal Forw Enable Auto 1000 Full Up Enable Enable N/A2 Normal Disa Enable Auto 1000 Full Down Enable Enable N/A3 Normal Disa Enable Auto 1000 Full Down Enable Enable N/A4 Normal Disa Enable Auto 1000 Full Down Enable Enable N/A
Note
config ap port, config network dsport, config mirror port, config port adminmode, config port linktrap, config port power
show qos queue_length all
To display quality of service (QoS) information (queue length), use the show qos command.
show qos queue_length all
Syntax Description
show
Display configurations.
qos
Quality of Service information.
queue_length all
Display queue lengths.
Defaults
None.
Examples
> show qos queue_length allPlatinum queue length.......................... 255Gold queue length.............................. 255Silver queue length............................ 150Bronze queue length............................ 100Related Commands
config qos
SHOW RADIUS COMMANDS
Use the SHOW RADIUS commands to display RADIUS settings.
show radius acct statistics
To display the RADIUS accounting server statistics for the Cisco Wireless LAN controller, use the show radius acct statistics command.
show radius acct statistics
Syntax Description
show
Display configurations.
radius acct
RADIUS accounting server.
statistics
Displays RADIUS accounting server statistics.
Defaults
None.
Examples
> show radius acct statisticsAccounting Servers:Server Index..................................... 1Server Address................................... 10.1.17.10Msg Round Trip Time.............................. 0 (1/100 second)First Requests................................... 0Retry Requests................................... 0Accounting Responses............................. 0Malformed Msgs................................... 0Bad Authenticator Msgs........................... 0Pending Requests................................. 0Timeout Requests................................. 0Unknowntype Msgs................................. 0Other Drops...................................... 0Related Commands
show radius auth statistics, show radius summary
show radius auth statistics
To display the RADIUS authentication server statistics for the Cisco Wireless LAN controller, use the show radius auth statistics command.
show radius auth statistics
Syntax Description
show
Display configurations.
radius auth
RADIUS authentication server.
statistics
Display RADIUS authentication server statistics.
Defaults
None.
Examples
> show radius auth statisticsAuthentication Servers:Server Index..................................... 1Server Address................................... 1.1.1.1Msg Round Trip Time.............................. 0 (1/100 second)First Requests................................... 0Retry Requests................................... 0Accept Responses................................. 0Reject Responses................................. 0Challenge Responses.............................. 0Malformed Msgs................................... 0Bad Authenticator Msgs........................... 0Pending Requests................................. 0Timeout Requests................................. 0Unknowntype Msgs................................. 0Other Drops...................................... 0Related Commands
show radius acct statistics, show radius summary
show radius rfc3576 statistics
To display the RADIUS rfc3576 server statistics for the Cisco Wireless LAN controller, use the show radius rfc3576 statistics command.
RFC 3576, an extension to the RADIUS protocol, allows dynamic changes to a user session. This includes support for disconnecting users and changing authorizations applicable to a user session; that is, it provides support for Disconnect and Change-of-Authorization (CoA) messages. Disconnect messages cause a user session to be terminated immediately, whereas CoA messages modify session authorization attributes such as data filters.
show radius rfc3576 statistics
Syntax Description
show
Display configurations.
radius rfc3576
RADIUS RFC3576 server.
statistics
Display RADIUS RFC-3576 server statistics.
Defaults
None.
Examples
> show radius rfc3576 statisticsRFC-3576 Servers:Server Index..................................... 1Server Address................................... 10.1.17.10Msg Round Trip Time.............................. 0 (1/100 second)First Requests................................... 0Retry Requests................................... 0Accounting Responses............................. 0Malformed Msgs................................... 0Bad Authenticator Msgs........................... 0Pending Requests................................. 0Timeout Requests................................. 0Unknown type Msgs................................. 0Other Drops...................................... 0Related Commands
show radius auth statistics, show radius summary, show radius rfc3576
show radius summary
To display the RADIUS authentication and accounting server summary, use the show radius summary command.
show radius summary
Syntax Description
Defaults
None.
Examples
> show radius summaryVendor Id Backward Compatibility................. DisabledCredentials Caching.............................. DisabledCall Station Id Type............................. IP AddressAdministrative Authentication via RADIUS......... EnabledAuthentication ServersIndex Type Server Address Port State Tout RFC-3576 IPSec - AuthMode/Phase1/Group/Lifetime/Auth/Encr----- ---- ---------------- ------ -------- ---- -------- ------------------------------------------------Accounting ServersIndex Type Server Address Port State Tout RFC-3576 IPSec - AuthMode/Phase1/Group/Lifetime/Auth/Encr----- ---- ---------------- ------ -------- ---- -------- ------------------------------------------------Related Commands
show radius auth statistics, show radius acct statistics
SHOW RFID COMMANDS
Use the SHOW RFID commands to display rfid settings.
show rfid config
To display Radio Frequency Identification (RFID) tag tracking information, use the show rfid config command.
show rfid config
Syntax Description
show
Display configurations.
rfid
Network configuration.
config
Configuration options for RFID tag tracking.
Defaults
None.
Examples
> show rfid configRFID Tag data Collection.................... EnabledRRID Tag Auto-Timeout....................... EnableRFID Client data Collection................. DisabledRFID data timeout........................... 1200 secondsRelated Commands
config rfid, show rfid summary, show rfid detail.
show rfid detail
To display detailed information about an RFID tag, use the show rfid detail command.
show rfid detail MAC
Syntax Description
show
Display configurations.
rfid
Network configuration.
detail
Detailed information for one RFID tag.
MAC
Show tag details for this MAC address.
Defaults
None.
Examples
> show rfid detail xx:xx:xx:xx:xx:xxRelated Commands
config rfid, show rfid config, show rfid summary.
show rfid summary
To display summary information about all known RFID tag tracking tags, use the show rfid summary command.
show rfid summary
Syntax Description
show
Display configurations.
rfid
Network configuration.
summary
Summary information for all known RFID tags.
Defaults
None.
Examples
> show rfid summaryRFID ID TYPE Closest AP RSSI Time Since Last Heard-------------- ------ ------------- ------ ---------------------Related Commands
config rfid, show rfid config, show rfid detail.
SHOW ROGUE ADHOC COMMANDS
Use the ROGUE ADHOC commands rogue adhoc settings.
show rogue adhoc detailed
To show details of an ad-hoc rogue access point detected by the Cisco Wireless LAN controller, use the show rogue adhoc client detailed command.
show rogue adhoc detailed MAC
Syntax Description
show
Display configurations.
rogue adhoc
Ad-hoc rogue.
detailed
Display detailed information.
MAC
Ad-hoc rogue MAC address.
Defaults
None.
Examples
> show rogue adhoc detailed 00:40:96:90:d1:6aAdhoc Rogue MAC Address........................ 00:40:96:90:d1:6aState.......................................... AlertFirst Time Adhoc Rogue was Reported............ Sat Aug 9 15:48:50 2003Last Time Adhoc Rogue was Reported............. Sat Aug 9 21:16:50 2003Reported ByAP 1MAC Address............................ 00:0b:85:01:88:b0Name................................... AP1Radio Type............................. 802.11bSSID................................... ChichenChannel................................ 6RSSI................................... -60 dBmSNR.................................... 40 dBRelated Commands
show rogue adhoc summary
show rogue adhoc summary
To display a summary of the ad-hoc rogue access points detected by the Cisco Wireless LAN controller, use the show rogue adhoc summary command.
show rogue adhoc summary
Syntax Description
show
Display configurations.
rogue adhoc
Ad-hoc rogue access point.
summary
Displays a list of all Adhoc Rogues.
Defaults
None.
Examples
> show rogue adhoc summaryClient MAC Address Adhoc BSSID State # APs Last Heard------------------ ----- ----- ----- --- -------xx:xx:xx:xx:xx:xx Alert 1 Sat Aug 9 21:12:50 2004xx:xx:xx:xx:xx:xx Alert 1 Aug 9 21:12:50 2003xx:xx:xx:xx:xx:xx Alert 1 Sat Aug 9 21:10:50 2003Related Commands
show rogue adhoc detailed
SHOW ROGUE AP COMMANDS
Use the ROGUE AP commands to display rogue access point settings.
show rogue ap clients
To show details of a rogue access point clients detected by the Cisco Wireless LAN controller, use the show rogue ap clients command.
show rogue ap clients MAC
Syntax Description
show
Display configurations.
rogue ap
Rogue access point.
clients
Summary information.
MAC
Rogue access point MAC address.
Defaults
None.
Examples
> show rogue ap clients xx:xx:xx:xx:xx:xxRelated Commands
show rogue ap summary
show rogue ap detailed
To show details of a rogue access point detected by the Cisco Wireless LAN controller, use the show rogue-ap detailed command.
show rogue ap detailed MAC
Syntax Description
show
Display configurations.
rogue ap
Rogue access point.
detailed
Display detailed information.
MAC
Rogue access point MAC address.
Defaults
None.
Examples
> show rogue ap detailed xx:xx:xx:xx:xx:xxRogue BSSID...................................... xx:xx:xx:xx:xx:xxIs Rogue on Wired Network........................ No (Unknown if WEP is enabled)State............................................ AlertFirst Time Rogue was Reported.................... Thu Aug 4 16:03:08 2005Last Time Rogue was Reported..................... Thu Aug 4 19:06:08 2005Reported ByAP 1MAC Address.............................. xx:xx:xx:xx:xx:xxName..................................... AP02Radio Type............................... 802.11aSSID..................................... vwentChannel.................................. 60RSSI..................................... -80 dBmSNR...................................... 8 dBEncryption............................... DisabledShortPreamble............................ DisabledWPA Support.............................. DisabledLast reported by this AP................. Thu Aug 4 19:06:08 2005Related Commands
show rogue ap summary, show rogue ap clients
show rogue ap summary
To display a summary of the rogue access points detected by the Cisco Wireless LAN controller, use the show rogue-ap summary command.
show rogue ap summary
Syntax Description
show
Display configurations.
rogue ap
Rogue access point.
summary
Display a list of all rogue access points.
Defaults
None.
Examples
> show rogue ap summaryRogue Location Discovery Protocol................ DisabledRLDP Auto-Contain................................ DisabledMAC Address State # APs # Clients Last Heard----------------- ------------------ ----- --------- -----------------------xx:xx:xx:xx:xx:xx Alert 1 0 Thu Aug 4 18:57:11 2005xx:xx:xx:xx:xx:xx Alert 1 0 Thu Aug 4 19:00:11 2005xx:xx:xx:xx:xx:xx Alert 1 0 Thu Aug 4 18:57:11 2005xx:xx:xx:xx:xx:xx Alert 1 0 Thu Aug 4 18:57:11 2005Related Commands
show rogue ap detailed, show rogue ap clients
SHOW ROGUE CLIENT COMMANDS
Use the following ROGUE CLIENT commands to display the rogue client settings.
show rogue client detailed
To show details of a rogue client detected by a Cisco Wireless LAN controller, use the show rogue client detailed command.
show rogue client detailed MAC
Syntax Description
show
Display configurations.
rogue client
Rogue client.
detailed
Provide detailed information for a rogue client.
MAC
Rogue client MAC address.
Defaults
None.
Examples
> show rogue client detailed xx:xx:xx:xx:xx:xxRogue BSSID...................................... xx:xx:xx:xx:xx:xxState............................................ AlertFirst Time Rogue was Reported.................... Thu Aug 4 18:51:08 2005Last Time Rogue was Reported..................... Thu Aug 4 19:00:08 2005Rogue Client IP address.......................... 192.168.1.117Reported ByAP 1MAC Address.............................. xx:xx:xx:xx:xx:xxName..................................... AP02Radio Type............................... 802.11aRSSI..................................... -1 dBmSNR...................................... -1 dBChannel.................................. 56Last reported by this AP................. Thu Aug 4 19:00:08 2005Related Commands
show rogue client summary
show rogue client summary
To display a summary of the rogue clients detected by the Cisco Wireless LAN controller, use the show rogue client summary command.
show rogue client summary
Syntax Description
show
Display configurations.
rogue client
Rogue client.
summary
Display a list of all rogue clients.
Defaults
None.
Examples
> show rogue client summaryMAC Address State # APs Last Heard----------------- ------------------ ----- -----------------------xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:00:08 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:00:08 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:00:08 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:00:08 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:00:08 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:00:08 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:09:11 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:03:11 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:03:11 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:09:11 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 18:57:08 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:12:08 2005Related Commands
show rogue client detailed
show route summary
To show the routes assigned to the Cisco Wireless LAN controller service port, use the show route summary command.
show route summary
Syntax Description
Defaults
None.
Examples
> show route summaryNumber of Routes............................... 1Destination Network Genmask Gateway------------------- ------------------- -------------------xxx.xxx.xxx.xxx 255.255.255.0 xxx.xxx.xxx.xxxRelated Commands
config route
show rules
To show the active internal firewall rules, use the show rules command.
show rules
Syntax Description
Defaults
None.
Examples
> show rules--------------------------------------------------------Rule ID.............: 3Ref count...........: 0Precedence..........: 99999999Flags...............: 00000001 ( PASS )Source IP range:(Local stack)Destination IP range:(Local stack)--------------------------------------------------------Rule ID.............: 25Ref count...........: 0Precedence..........: 99999999Flags...............: 00000001 ( PASS )Service InfoService name........: GDBProtocol............: 6Source port low.....: 0Source port high....: 0Dest port low.......: 1000Dest port high......: 1000Source IP range:IP High............: 0.0.0.0Interface..........: ANYDestination IP range:(Local stack)--------------------------------------------------------...Related Commands
None.
show run-config
To show a comprehensive view of the current Cisco Wireless LAN controller configuration, use the show run-config command.
show run-config
Syntax Description
Defaults
None.
Examples
> show run-configPress Enter to continue...System InventorySwitch Description............................... Cisco ControllerMachine Model....................................Serial Number.................................... FLS0923003BBurned-in MAC Address............................ xx:xx:xx:xx:xx:xxCrypto Accelerator 1............................. AbsentCrypto Accelerator 2............................. AbsentPower Supply 1................................... AbsentPower Supply 2................................... Present, OKPress Enter to continue Or <Ctl Z> to abort...
Note
Related Commands
config route
show serial
To show the serial (console) port configuration, use the show serial command.
show serial
Syntax Description
Defaults
9600, 8, off, 1, none.
Examples
> show serialSerial Port Login Timeout (minutes)......... 45Baud Rate................................... 9600Character Size.............................. 8Flow Control:............................... DisableStop Bits................................... 1Parity Type:................................ noneRelated Commands
config serial baudrate, config serial timeout
show sessions
To show the console port login timeout and maximum number of simultaneous Command Line Interface (CLI) sessions, use the show sessions command.
show sessions
Syntax Description
Defaults
5 minutes, 5 sessions.
Examples
> show sessionsCLI Login Timeout (minutes)............ 0Maximum Number of CLI Sessions......... 5The response indicates that the CLI sessions never time out and that the Cisco Wireless LAN controller can host up to five simultaneous CLI sessions.
Related Commands
config sessions maxsessions, config sessions timeout
show snmpcommunity
To display SNMP community entries, use the show snmpcommunity command.
show snmpcommunity
Syntax Description
Defaults
None.
Examples
> show snmpcommunitySNMP Community Name Client IP Address Client IP Mask Access Mode Status------------------- ----------------- ----------------- ----------- --------public 0.0.0.0 0.0.0.0 Read Only Enable********** 0.0.0.0 0.0.0.0 Read/Write EnableRelated Commands
config snmp version, config snmp community mode, config snmp community accessmode, config snmp community create, config snmp community delete, config snmp community ipaddr
show snmptrap
To show the Cisco Wireless LAN controller SNMP trap receivers and their status, use the show snmptrap command.
show snmptrap
Syntax Description
Defaults
None.
Examples
> show snmptrapSNMP Trap Receiver Name IP Address Status------------------------ ----------------- --------xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx EnableRelated Commands
config snmp version, config snmp trapreceiver
show snmpv3user
To show the SNMP version 3 configuration, use the show snmpv3user command.
show snmpv3user
Syntax Description
Defaults
None.
Examples
> show snmpv3userSNMP v3 User Name AccessMode Authentication Encryption-------------------- ----------- -------------- ----------default Read/Write HMAC-MD5 CBC-DESRelated Commands
config snmp version, config snmp v3user
show snmpversion
To show the SNMP version status, use the show snmpversion command.
show snmpversion
Syntax Description
Defaults
Enable.
Examples
> show snmpversionSNMP v1 Mode.................................. DisableSNMP v2c Mode.................................. EnableSNMP v3 Mode.................................. EnableRelated Commands
config snmp version
show spanningtree port
To show the Cisco Wireless LAN controller spanning tree port configuration, use the show spanningtree port command.
When the a Cisco 4400 Series wireless LAN controller is configured for port redundancy, spanning tree protocol must be disabled for all ports on the Cisco 4400 series wireless LAN controller. Spanning tree protocol can remain enabled on the switch connected to the Cisco 4400 series wireless LAN controller.
show spanningtree port port
Syntax Description
Note
Defaults
800C, Disabled, 802.1D, 128, 100, Auto.
Examples
> show spanningtree port 3STP Port ID................................. 800CSTP Port State.............................. DisabledSTP Port Administrative Mode................ 802.1DSTP Port Priority........................... 128STP Port Path Cost.......................... 100STP Port Path Cost Mode..................... AutoRelated Commands
config spanningtree port
show spanningtree switch
To show the Cisco Wireless LAN controller network (DS port) spanning tree configuration, use the show spanningtree switch command.
show spanningtree switch
Syntax Description
show
Display configurations.
spanningtree
Spanning tree.
switch
Display spanning tree values on a per switch basis.
Note
Defaults
None.
Examples
> show spanningtree switchSTP Specification...................... IEEE 802.1DSTP Base MAC Address................... 00:0B:85:02:0D:20Spanning Tree Algorithm................ DisableSTP Bridge Priority.................... 32768STP Bridge Max. Age (seconds).......... 20STP Bridge Hello Time (seconds)........ 2STP Bridge Forward Delay (seconds)..... 15Related Commands
config spanningtree switch bridgepriority, config spanningtree switch forwarddelay, config spanningtree switch hellotime, config spanningtree switch maxage, config spanningtree switch mode
SHOW STATS COMMANDS
Use the SHOW STATS commands to display controller statistics.
show stats port
To show physical port receive and transmit statistics, use the show stats port command.
show stats port {detailed port | summary port}
Syntax Description
Defaults
None.
Examples
> show stats port summary 1Packets Received Without Error................. 399958Packets Received With Error.................... 0Broadcast Packets Received..................... 8350Packets Transmitted Without Error.............. 106060Transmit Packets Errors........................ 0Collisions Frames.............................. 0Time Since Counters Last Cleared............... 2 day 11 hr 16 min 23 sec> show stats port detailed 1PACKETS RECEIVED (OCTETS)Total Bytes...................................... 26779988164 byte pkts :91828165-127 byte pkts :354016 128-255 byte pkts :1283092256-511 byte pkts :8406 512-1023 byte pkts :30061024-1518 byte pkts :1184 1519-1530 byte pkts :0> 1530 byte pkts :2PACKETS RECEIVED SUCCESSFULLYTotal............................................ 2567987Unicast Pkts :2547844 Multicast Pkts:0 Broadcast Pkts:20143PACKETS RECEIVED WITH MAC ERRORSTotal............................................ 0Jabbers :0 Undersize :0 Alignment :0FCS Errors:0 Overruns :0RECEIVED PACKETS NOT FORWARDEDTotal............................................ 0Local Traffic Frames:0 RX Pause Frames :0Unacceptable Frames :0 VLAN Membership :0VLAN Viable Discards:0 MulticastTree Viable:0ReserveAddr Discards:0CFI Discards :0 Upstream Threshold :0PACKETS TRANSMITTED (OCTETS)Total Bytes...................................... 35383164 byte pkts :0 65-127 byte pkts :0128-255 byte pkts :0 256-511 byte pkts :0512-1023 byte pkts :0 1024-1518 byte pkts :21519-1530 byte pkts :0 Max Info :1522PACKETS TRANSMITTED SUCCESSFULLYTotal............................................ 5875Unicast Pkts :5868 Multicast Pkts:0 Broadcast Pkts:7TRANSMIT ERRORSTotal Errors..................................... 0FCS Error :0 TX Oversized :0 Underrun Error:0TRANSMIT DISCARDSTotal Discards................................... 0Single Coll Frames :0 Multiple Coll Frames:0Excessive Coll Frame:0 Port Membership :0VLAN Viable Discards:0PROTOCOL STATISTICSBPDUs Received :6 BPDUs Transmitted :0802.3x RX PauseFrame:0Time Since Counters Last Cleared............... 2 day 0 hr 39 min 59 secRelated Commands
config port adminmode
show stats switch
To show the network (DS port) receive and transmit statistics, use the show stats switch command.
show stats switch {detailed | summary}
Syntax Description
show
Display configurations.
stats
Statistics.
switch
Cisco Wireless LAN controller.
detailed
Display detailed switch statistics.
summary
Display switch summary statistics.
Defaults
None.
Examples
> show stats switch summaryPackets Received Without Error................. 136410Broadcast Packets Received..................... 18805Packets Received With Error.................... 0Packets Transmitted Without Error.............. 78002Broadcast Packets Transmitted.................. 3340Transmit Packet Errors......................... 2Address Entries Currently In Use............... 26VLAN Entries Currently In Use.................. 1Time Since Counters Last Cleared............... 2 day 11 hr 22 min 17 sec> show stats switch detailedRECEIVEOctets........................................... 19351718Total Pkts....................................... 183468Unicast Pkts..................................... 180230Multicast Pkts................................... 3219Broadcast Pkts................................... 19Pkts Discarded................................... 0TRANSMITOctets........................................... 354251Total Pkts....................................... 5882Unicast Pkts..................................... 5875Multicast Pkts................................... 0Broadcast Pkts................................... 7Pkts Discarded................................... 0ADDRESS ENTRIESMost Ever Used................................... 1Currently In Use................................. 1VLAN ENTRIESMaximum.......................................... 128Most Ever Used................................... 1Static In Use.................................... 1Dynamic In Use................................... 0VLANs Deleted.................................... 0Time Since Ctrs Last Cleared..................... 2 day 0 hr 43 min 22 secRelated Commands
config network dsport
show switchconfig
To display parameters that apply to the Cisco Wireless LAN controller use the show switchconfig command.
show switchconfig
Syntax Description
show
Display configurations.
switchconfig
Display parameters that apply to the Cisco Wireless LAN controller.
Defaults
None.
Examples
> show switchconfig802.3x Flow Control Mode......................... DisableCurrent LWAPP Transport Mode..................... Layer 3LWAPP Transport Mode after next switch reboot.... Layer 3Related Commands
config switchconfig flowcontrol, config switchconfig mode
show sysinfo
To show high-level Cisco Wireless LAN controller information, use the show sysinfo command.
show sysinfo
Syntax Description
Defaults
None.
Examples
> show sysinfoManufacturer's Name.......................... <company name>Product Name.................................Product Version.............................. 1.2.48.0RTOS Version................................. 1.2.48.0Bootloader Version........................... 1.1.11.0System Name.................................. IT2003System Location.............................. Andrew 1System Contact............................... Wireless_administratorSystem ObjectID.............................. 1.3.6.1.4.1.14179IP Address................................... 172.168.2.36System Up Time............................... 2 days 11 hrs 30 mins 1 secsConfigured Country........................... United StatesOperating Environment........................ Commercial (0 to 40 C)Internal Temp Alarm Limits................... 0 to 65 CInternal Temperature......................... +38 CState of 802.11b Network..................... EnabledState of 802.11a Network..................... EnabledNumber of WLANs.............................. 23rd Party Access Point Support............... DisabledNumber of Active Clients..................... 1xxxxxxxxxxxxxxxxxRelated Commands
config ap, config country, config sysname, config wlan
show syslog
To show the Cisco Wireless LAN controller SNMP trap logging status or target IP Address, use the show syslog command.
show syslog
Syntax Description
Defaults
None.
Examples
> show syslogSyslog destination............................. disabled> show syslogSyslog destination............................. xxx.xxx.xxx.xxxRelated Commands
config syslog
show tech-support
To show Cisco Wireless LAN controller variables frequently requested by Cisco Technical Assistance Center (TAC), use the show tech-support command.
show tech-support
Syntax Description
Defaults
None.
Examples
> show tech-supportCurrent CPU Load................................. 0%System BuffersMax Free Buffers.............................. 4608Free Buffers.................................. 4604Buffers In Use................................ 4Web Server ResourcesDescriptors Allocated......................... 152Descriptors Used.............................. 3Segments Allocated............................ 152Segments Used................................. 3System ResourcesUptime........................................ 747040 SecsTotal Ram..................................... 127552 KbytesFree Ram...................................... 19540 Kbytes
