Configuring a Supervisor Engine 32 PISA
This chapter describes how to configure a Supervisor Engine 32 PISA (Supervisor Engine 32 with a programmable intelligent services accelerator) in a Catalyst 6500 series switch. This chapter contains these sections:
•Flash Memory on a Supervisor Engine 32 PISA
•Supervisor Engine 32 PISA Ports
•Configuring Full PISA EtherChannel Bandwidth
•Displaying PISA Platform Statistics
Note•For complete syntax and usage information for the commands used in this chapter, see the Catalyst Supervisor Engine 32 PISA Cisco IOS Command Reference, Release 12.2ZY, at this URL:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2ZY/command/reference/cmdref.html
•This is the minimum required Supervisor Engine 32 PISA memory:
–512-MB DRAM on the Supervisor Engine 32
–1-GB DRAM on the PISA daughterboard
•Supervisor Engine 32 PISA has a PFC3B and operates in PFC3B mode.
•With a 3-slot or a 4-slot chassis, install the Supervisor Engine 32 PISA in either slot 1 or 2.
•With a 6-slot or a 9-slot chassis, install the Supervisor Engine 32 PISA in either slot 5 or 6.
•With a 13-slot chassis, install the Supervisor Engine 32 PISA in either slot 7 or 8.
•Supervisor Engine 32 PISA does not support switch fabric connectivity.
•For information about the hardware and software features supported by the Supervisor Engine 32 PISA, see the Release Notes for Cisco IOS Release 12.2ZY on the Supervisor Engine 32 PISA at this URL:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2ZY/release/notes/ol_13011.html
Flash Memory on a Supervisor Engine 32 PISA
The Supervisor Engine 32 PISA has these flash memory devices:
•disk0:
–One external CompactFlash Type II slot
–Supports CompactFlash Type II flash PC cards
•sup-bootdisk:
–Supervisor Engine 32 256-MB internal CompactFlash flash memory
–From the Supervisor Engine 32 ROMMON, it is bootdisk:
•bootdisk:
–PISA 256-MB internal CompactFlash flash memory
–Not accessible from the Supervisor Engine 32 ROMMON
Supervisor Engine 32 PISA Ports
These sections describe the ports on a Supervisor Engine 32 PISA:
•Supervisor Engine 32 PISA Management Ports
•Supervisor Engine 32 PISA Data Ports
Supervisor Engine 32 PISA Management Ports
The console port for the Supervisor Engine 32 PISA port is an EIA/TIA-232 (RS-232) port. The Supervisor Engine 32 PISA also has two Universal Serial Bus (USB) 2.0 ports that currently are not enabled.
Supervisor Engine 32 PISA Data Ports
The WS-S32-10GE-PISA has these ports:
•Ports 1 and 2: XENPAK 10 Gigabit Ethernet
•Port 3: 10/100/1000 Mbps RJ-45
Note•To avoid unexpected application of QoS to the PISA EtherChannel, do not configure QoS on WS-S32-10GE-PISA ports.
•You can disable Port 3 and reallocate its port ASIC capacity to the PISA EtherChannel (see the "Configuring Full PISA EtherChannel Bandwidth" section section).
The WS-S32-GE-PISA has these ports:
•Ports 1 through 8: Small form-factor pluggable (SFP) Gigabit Ethernet
•Port 9: 10/100/1000 Mbps RJ-45 port
Note•To avoid unexpected application of QoS to the PISA EtherChannel, do not configure QoS on WS-S32-GE-PISA ports.
•You can disable port 9 and reallocate its port ASIC capacity to the PISA EtherChannel (see the "Configuring Full PISA EtherChannel Bandwidth" section section).
Configuring Full PISA EtherChannel Bandwidth
A Supervisor Engine 32 PISA automatically creates an EtherChannel (port channel interface 256) that the Supervisor Engine 32 and the PISA daughterboard use to communicate with each other. By default, the PISA EtherChannel bandwidth is 1 Gbps. To increase the PISA EtherChannel bandwidth, you can disable supervisor engine ports and reallocate the port ASIC capacity to the PISA EtherChannel.
To increase the PISA EtherChannel bandwidth, perform this task:
|
|
|
Step 1 |
Router(config)# interface gigabitethernet slot/3 Or: |
On a WS-S32-10GE-PISA, selects the Ethernet port to be configured. |
Router(config)# interface gigabitethernet slot/[8 | 9] |
On a WS-S32-GE-PISA, selects the Ethernet port to be configured. Note On a WS-S32-GE-PISA, you can allocate both ports 8 and 9 to the PISA EtherChannel. |
Step 2 |
Router(config-if)# channel-group 256 mode on |
Disables the port and allocates its port ASIC capacity to the PISA EtherChannel. |
Router(config-if)# no channel-group 256 mode on |
Reverts to the default port ASIC capacity allocation. |
Note•You cannot enter any configuration under port channel interface 256.
•After the port becomes a member of the PISA EtherChannel, only the no channel-group 256 mode on command has any effect on the port until the port is no longer a member of the PISA EtherChannel. While the port is a member of the PISA EtherChannel, all port configuration commands except the [no] channel-group 256 mode on command are ignored.
•The PISA EtherChannel MTU size is 4,096 bytes.
This example shows how to allocate the port ASIC capacity of port 3 to the PISA EtherChannel on a WS-S32-10GE-PISA that is installed in slot 5:
Router# configure terminal
Router(config)# interface gigabitethernet 5/3
Router(config-if)# channel-group 256 mode on
Router(config-if)# end
This example shows how to allocate the port ASIC capacity of port 9 to the PISA EtherChannel on a WS-S32-GE-PISA that is installed in slot 5:
Router# configure terminal
Router(config)# interface gigabitethernet 5/9
Router(config-if)# channel-group 256 mode on
Router(config-if)# end
Displaying PISA Platform Statistics
To display platform statistics for the Supervisor Engine 32 PISA, perform this task:
|
|
Router# show platform pisa np counter-type counters |
Displays platform statistics for the Supervisor Engine 32 PISA. •counter-type—See Table 4-1 for the list of valid values. |
Table 4-1 shows the available counters.
Table 4-1 PISA Platform Counters
|
|
me num |
Microengine information (valid num values are from 0 to 15) |
acl |
ACL counter information |
all |
All Supervisor Engine 32 PISA-specific counters |
all pps |
Packets per second (pps) for all Supervisor Engine 32 PISA-specific counters |
fpm |
Flexible packet matching (FPM) counters |
mqc |
Modular QoS CLI information |
nbar |
Network-based application recognition (NBAR) counter information |
rx |
Receive engine counters |
tx |
Transmit engine counters |
For examples of the show platform pisa np command output, see the Catalyst Supervisor Engine 32 PISA Cisco IOS Command Reference, Release 12.2ZY, at this URL:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2ZY/command/reference/cmdref.html
To clear platform counters for the Supervisor Engine 32 PISA, perform this task:
|
|
Cisco IOS Release 12.2(33)ZYA and earlier releases Router# clear platform pisa ixp counters counter-type Cisco IOS Release 12.2(33)ZYA1 and later releases Router# clear platform pisa np counter-type counters |
Displays platform statistics for the Supervisor Engine 32 PISA. •counter-type—See Table 4-1 for the list of valid values. |
This example shows how to clear the ACL counters in Cisco IOS Release 12.2(33)ZYA1 and later releases:
Router# clear platform pisa np acl counters