 Feedback
|
Table Of Contents
Memory and IOS Software Requirements
Determining the Firmware Version
Upgrading to a New Firmware Release
Cisco IOS Software Documentation Set
Obtaining Documentation, Obtaining Support, and Security
Release Notes for Cisco 880VA Series Multimode VDSL2/ADSL2/2+ DSL Router with firmware release A2pv6C032b.d23b
Published: January 24, 2011Last Revised: January 24, 2011, OL-24391-01Firmware Release: A2pv6C032b.d23bCisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)
Contents
•
Obtaining Documentation, Obtaining Support, and Security
Introduction
These release notes describe new enhancements and fixed caveats for the Cisco 880VA Series Multimode VDSL2/ADSL2/2+ DSL Routers using firmware release A2pv6C032b.d23b. These release notes are updated as needed.
System Requirements
This section describes the system requirements for firmware Release A2pv6C032b.d23b and includes the following sections:
•
•
•
Memory and IOS Software Requirements
Table 1 lists the memory and IOS Software requirements for the Cisco 880VA Series Multimode VDSL2/ADSL2/2+ DSL platforms, using firmware Release A2pv6C032b.d23b
Determining the Firmware Version
To determine the version of firmware currently running on your Cisco 880VA series router, issue the following IOS command and look for the output in BOLD:
Router#show controller vdsl 0Firmware Source File Name (version)-------- ------ -------------------VDSL user config flash:vdsl.bin.32bdslfw (10)Modem FW Version: 100929_1300-4.02L.03.A2pv6C032b.d23bModem PHY Version: A2pv6C032b.d23bUpgrading to a New Firmware Release
Perform the following steps to upgrade to a new firmware release:
1.
Choose Routers -> Branch Routers -> Cisco 800 Series Routers -> Cisco 887VA Integrated Services Router -> Very High Bitrate DSL (VDSL) Firmware
2.
3.
Router#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#controller vdsl 0Router(config-controller)#firmware filename ?archive: Download fw file namecns: Download fw file nameflash: Download fw file nameftp: Download fw file namehttp: Download fw file namehttps: Download fw file namenull: Download fw file namenvram: Download fw file namercp: Download fw file namescp: Download fw file namesystem: Download fw file nametar: Download fw file nametftp: Download fw file nametmpsys: Download fw file namexmodem: Download fw file nameymodem: Download fw file nameRouter(config-controller)#firmware filename flash:vdsl.bin.32bdslfw4.
Router#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#controller vdsl 0Router(config-controller)#shutRouter(config-controller)#no shutRouter(config-controller)#endRouter#Modem Settings
New modem commands are introduced with the release of the A2pv6C032b.d23b firmware and IOS release 15.1(2)T. These commands allow custom configurations of DSL modem settings to ensure DSL interoperability in different environments. Please consult your Service Provider on required modem settings for the particular SPs network.
Before you enable the modem settings, you must execute the service internal command in CONFIG mode. For example:
Router#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#service internalThe following list contains the modem settings:
UK Annex M FLAG
•
•
•
•
Note
•
–
test vdsl 0 modem exec adsl info—cfg
Bit 20 in adslAnnexAParam—ON
Bit 9 in adslDemodCap2Mask—ON
Bit 9 in adslDemodCap2Value—ON
adslAnnexAParam—00107985
adslDemodCap2Mask—00540200
adslDemodCap2Value—00540200
show controller vdsl 0 console—Custom UK Annex M Mask SET
–
test vdsl 0 modem exec adsl info—cfg
Bit 20 in adslAnnexAParam—OFF
Bit 9 in adslDemodCap2Mask—OFF
Bit 9 in adslDemodCap2Value—OFF
adslAnnexAParam—00007985
adslDemodCap2Mask—00540000
adslDemodCap2Value—00540000
show controller vdsl 0 console—Custom UK Annex M Mask NOT SET
UKfeature Carrier FLAG
•
•
•
•
Note
•
–
test vdsl 0 modem exec adsl info—cfg
Bit 21 vdslCfgFlagsMask—ON
Bit 21 vdslCfgFlagsValue—ON
xdslAuxFeaturesMask—00260003
xdslAuxFeaturesValue—00260003
show controller vdsl 0 console—ukfeatureBit SET
–
test vdsl 0 modem exec adsl info—cfg
Bit 21 vdslCfgFlagsMask—OFF
Bit 21 vdslCfgFlagsValue—OFF
xdslAuxFeaturesMask—00060003
xdslAuxFeaturesValue—00060003
show controller vdsl 0 console —ukfeatureBit CLEAR
CO5 FLAG
•
•
•
•
Note
•
–
test vdsl 0 modem exec adsl info—cfg
Bit 4 vdslCfgFlagsMask—ON
Bit 4 vdslCfgFlagsValue—ON
Bit 5 vdslCfgFlagsMask—ON
Bit 5 vdslCfgFlagsValue—ON
vdslCfgFlagsMask—00000434
vdslCfgFlagsValue—00000434
show controller vdsl 0 console—CO5 Flag SET
–
test vdsl 0 modem exec adsl info—cfg
Bit 4 vdslCfgFlagsMask—OFF
Bit 4 vdslCfgFlagsValue—OFF
Bit 5 vdslCfgFlagsMask—OFF
Bit 5 vdslCfgFlagsValue—OFF
vdslCfgFlagsMask—00000404
vdslCfgFlagsValue— 00000404
show controller vdsl 0 console—CO5 Flag NOT SET
"V.43" carrier set
•
•
•
•
Note
•
–
test vdsl 0 modem exec adsl info—cfg
Bit 16 vdslCfgFlagsMask—ON
Bit 16 vdslCfgFlagsValue—ON
vdslCfgFlagsMask—00010404
vdslCfgFlagsValue—00010404
show controller vdsl 0 console—Disable V43 SET
–
test vdsl 0 modem exec adsl info—cfg
Bit 16 vdslCfgFlagsMask—OFF
Bit 16 vdslCfgFlagsValue—OFF
vdslCfgFlagsMask—00000404
vdslCfgFlagsValue—00000404
show controller vdsl 0 console—Disable V43 CLEAR
"GinpDsSupport" carrier set
•
•
•
•
Note
•
–
test vdsl 0 modem exec adsl info—cfg
Bit 17 xdslAuxFeaturesMask—ON
Bit 17 xdslAuxFeaturesValue—ON
xdslAuxFeaturesMask—00040003
xdslAuxFeaturesValue—00040003
show controller vdsl 0 console—Disable GinpDsSupport
–
test vdsl 0 modem exec adsl info—cfg
Bit 17 xdslAuxFeaturesMask—OFF
Bit 17 xdslAuxFeaturesValue—OFF
xdslAuxFeaturesMask—00060003
xdslAuxFeaturesValue—00060003
show controller vdsl 0 console—Enable GinpDsSupport
New and Changed Information
This section contains changes introduced with firmware release A2pv6C032b.d23b.
VDSL interoperability improvements:
•
•
•
•
•
•
•
•
ADSL interoperability improvements:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Additional References
Use this release note with the documents and websites in this release note and the documents listed in
the following sections:
Release-Specific Documents
The following documents are specific to Release 15.0 and apply to Release 15.0(1)XA:
•
•
Platform-Specific Documents
Hardware installation guides, configuration and command reference guides, and additional documents
specific to the Cisco 800 series routers are available at:
http://www.cisco.com/en/US/products/hw/routers/ps380/tsd_products_support_series_home.html
Cisco IOS Software Documentation Set
The Cisco IOS software documentation set consists of the Cisco IOS configuration guides, Cisco IOS
command references, and several other supporting documents.
Documentation Modules
Each module in the Cisco IOS documentation set consists of one or more configuration guides and one
or more corresponding command references. Chapters in a configuration guide describe protocols,
configuration tasks, and Cisco IOS software functionality, and contain comprehensive configuration
examples. Chapters in a command reference provide complete command syntax information. Use each
configuration guide with its corresponding command reference. Cisco IOS Software Documentation is
available in html or pdf form.
Select your release and click the command references, configuration guides, or any other Cisco IOS
documentation you need.
Obtaining Documentation, Obtaining Support, and Security
For information on obtaining documentation, obtaining support, providing documentation feed-back,
security guidelines, and also recommended aliases and general Cisco documents, see the monthly What's
New in Cisco Product Documentation, which also lists all new and revised Cisco technical
documentation at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Notices
See the Notices section in About Cisco IOS Release Notes located at:
http://www.cisco.com/en/US/docs/ios/12_4/12_4x/12_4xy15/ReleaseNote.html.
Use this document in conjunction with the documents listed in the "Additional References" section.
