Feedback
Table Of Contents
Mean Time Between Failure Ground Benign Environment
Technical Specifications
This appendix provides router, port, cabling specifications, and power adapters for the Cisco 819 Integrated Services Router (ISRs) and contains the following sections:
•
Mean Time Between Failure Ground Benign Environment
Warning
Note
Router Specifications
Table A-1 lists the operational limits of the Cisco 819 ISR. Operating the router outside of the limits specified is not supported. For the complete list of SKUs available for each Cisco 819 ISRs, see the "SKU Information" section.
Table A-1 Cisco 819 ISR Specifications
Dimensions (H x W x D)
1.73 x 7.7 x 8.1 in
(44 x 196 x 206 mm)
1.67 x 7.7 x 7.2 in
(42 x 196 x 183 mm)
1.73 x 7.7 x 9.0 in
(44 x 196 x 229 mm)
Weight
3.2 lb (1.5 kg)
2.3 lb (1.0 kg)
3.4 lb (1.54 kg)
Maximum Power Consumption
11 W
20 W
Operating Temperature and Altitude
-13 to 140°F
(-25 to 60°C)
32 to 104°F
(0 to 40°C)
-13 to 140°F
(-25 to 60°C)
Derate max operating temperature 1.5°C per 1000 feet above 5000 ft
10,000 ft maximum
Humidity
Maximum 95% non-condensing RH
Maximum 85% non-condensing RH
Maximum 95% non-condensing RH
Ingress Protection Rating
IP 41 per IEC 60529 for Vertical Falling Water, Pollution Degree 3
IP 20 per IEC 60529
IP 41 per IEC 60529 for Vertical Falling Water, Pollution Degree 3
Humidity
Non-condensing Relative Humidity: 5% to 95%
Pollution
Pollution 3 for Dust
Military Standard
MIL-STD-810G Method 514.6: Procedure 1 Category 4, Secured Cargo - Common Carrier
MIL-STD-810G Method 514.6: Procedure 1 Category 20, Ground Vehicles
MIL-STD-810G Method 516.6. Procedure 1, Functional Shock
MIL-STD-810G Method 516.6. Procedure 5, Crash Hazard
MIL-STD-810G Method 516.6. Procedure 6, Bench Handling
Vibration and Shock (Railway Vehicles)
EN61373 Functional Random Vibe - Category 1, Class B
EN61373 Simulated Non-op Long-life Vibe - Category 1, Class B
EN61373 Non-op Shock, Class B
Heavy-Duty Vehicle Applications
SAE J1455 Operating Random Vibe, Cab Mounted Truck
SAE J1455 Operating Sinusoidal Vibe, Category 3
SAE J1455 Non-operating Sinusoidal Vibe, Category 3
SAE J1455 Handling Drop Test
Standard Safety Certifications
UL 60950-1, 2nd edition; CAN/CSA C22.2 No. 60950-1, 2nd edition, EN 60950-1, 2nd edition; CB to IEC 60950-1, 2nd edition with all group differences and national deviations
UL 60950-1, 2nd edition; CAN/CSA C22.2 No. 60950-1, 2nd edition, EN 60950-1, 2nd edition; CB to IEC 60950-1, 2nd edition with all group differences and national deviations; S/NZS 60950-1, first edition (Australia/New Zealand)
EMC Emissions
EN55022/CISPR22, CFR 47 Part 15, ICES003, VCCI-V-3, AS/NZS CISPR22, CNS13438, CISPR22, CNS13438, EN300-386, EN61000-3-2, EN61000-3-3, and EN61000-6-1
EMC Immunity
EN55024/CISPR24, (EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-11), and EN300-386
Radio Immunity
EN301 489-1, EN 301 489-7, and EN301 489-24
Temperature
-40 to158°F (-40 to 70°C)
-40 to185°F
(-40 to 85°C)
Humidity
5-95%
Altitude
4570 m (15,000 ft)
Input Voltage
85-264 VAC
100-240 VAC nominal
Maximum Power Consumption
25 W
Maximum Output Power Rating
20 W
(5 VDC, 4 Amps)
Input Voltage
12 VDC nominal
PWRx-20W-12VDC (10 VDC to 36 VDC operating range)
24 VDC nominal
PWRx-20W-24VDC (18 VDC to 75 VDC operating range)
Maximum Power Consumption
25 W
Maximum Output Power Rating
20 W
(5 VDC, 4 Amps)
Altitude
Operating: -500 to 10,000 ft, de-rating operating temperature 1°C per 1,000 feet
Non-operating: -1,000 to 30,000 ft
Cable Length
Input cable: 1 m
Output cable: 1.3 m
Inrush Current
50 A @ 25°C
Temperature
Operating: -30 to 60°C, still air condition
Non-operating: -40 to 85°C
Humidity
Operating: 10% to 95%, non-condensing
Non-operating: 10% to 95%, non-condensing
Thermal Shock
Operating: -20 to 60°C at 0.5°C per minute
Non-operating: -40 to 85°C with change over time between 2 and 3 minutes.
Vibration
Operating: 0.41 grms from 3 to 500 Hz with spectral break points of 0.0005 g2/Hz at 10 Hz and 200 Hz and 5 dB/octave roll off at each end; 2 hours per axis.
Non-Operating: 1.12 grms from 3 to 500 Hz with spectral break points of 0.0065 g2/Hz at 10 Hz and 100 Hz and 5 dB/octave roll off at each end; 30 minutes per axis.
Shock
Half sine (operating):
Duration = <2ms
Velocity = 2.11m/s
Number of shocks: a series of 6 shocks one on each sideTrapezoidal shock (non-operating):
Duration = 12 to 25 ms
Number of shocks: a series of 6 shocks one on each sideNominal Input Voltages
—
—
24 V
52 V
72 V
In-ceiling Plenum
—
—
No
IP 65
—
—
Yes
Extended Shock-vibe
—
—
Yes
EN50155 (EN61373) and RIA20
Maximum Power Consumption
—
—
25 W
Maximum Output Power Rating
—
—
20 W
Operating Temperature
—
—
-13 to 140°F
(-25 to 60°C)
Antenna Dimensions
7.63 x 0.94 x 0.63 in (19.38 x 2.39 x 1.60 cm)
Frequency Range
806 to 960 MHz and 1710 to 2170 MHz
Gain
0 decibels relative to isotropic (dBi) (806 to 960 MHz) and 0 dBi (1710 to 2170 MHz)
Maximum Power
25 W
Connector
TNC male
Voltage Standing Wave Ratio
< 2.5:1
Nominal Impedance
50 ohms
1 AC Power Adapter is not IP 41 rated. Installation must include protection of the adapter and power plug from water.
2 Contact Martek Power directly for details.
Mean Time Between Failure Ground Benign Environment
Table A-2 lists the Mean Time Between Failire (MTBF) values for Cisco 819 ISRs. The MTBF is calculated based on the Ground Benign condition. The values may be adjusted based on the different router usage.
Supported Power Adapters
Table A-3 and Table A-4 list the supported power adapters for Cisco 819 ISRs. The PWR1 AC and DC adapters uses molex connector while PWR2 uses barrel-type connector.
Note
1 Quarter 1 Calendar Year 2013.
