Table Of Contents

ED Commands

11.1  ED-<GIGE_TYPE>

11.2  ED-<MOD1FCPAYLOAD>

11.3  ED-<MOD1FICONPAYLOAD>

11.4  ED-<MOD2DWDMPAYLOAD>

11.5  ED-<MOD_PATH>

11.6  ED-<MOD_RING>

11.7  ED-<OCN_TYPE>

11.8  ED-ALS

11.9  ED-APC

11.10  ED-BITS

11.11  ED-BULKROLL-<OCN_TYPE>

11.12  ED-BWP-ETH

11.13  ED-CMD-SECU

11.14  ED-COS-ETH

11.15  ED-CRS-<PATH>

11.16  ED-CRS-ETH

11.17  ED-DAT

11.18  ED-DS1

11.19  ED-EC1

11.20  ED-ETH

11.21  ED-EQPT

11.22  ED-FAC

11.23  ED-FFP-<MOD2DWDMPAYLOAD>

11.24  ED-FFP-<OCN_TYPE>

11.25  ED-FFP-OCH

11.26  ED-FFP-OTS

11.27  ED-FSTE

11.28  ED-FTPSERVER

11.29  ED-G1000

11.30  ED-GFP

11.31  ED-HDLC

11.32  ED-L2-ETH

11.33  ED-LMP

11.34  ED-LMP-CTRL

11.35  ED-LMP-TLINK

11.36  ED-LMP-DLINK

11.37  ED-LNK

11.38  ED-LNKTERM

11.39  ED-MCAST

11.40  ED-NE-GEN

11.41  ED-NE-PATH

11.42  ED-NE-SYNCN

11.43  ED-OCH

11.44  ED-OCHCC

11.45  ED-OCHNC

11.46  ED-OMS

11.47  ED-OTS

11.48  ED-PID

11.49  ED-POS

11.50  ED-PROTOCOL

11.51  ED-QNQ-ETH

11.52  ED-ROLL-<MOD_PATH>

11.53  ED-SLV-WDMANS

11.54  ED-SYNCN

11.55  ED-T1

11.56  ED-T3

11.57  ED-TRAPTABLE

11.58  ED-TRC-OCH

11.59  ED-USER-SECU

11.60  ED-VCG

11.61  ED-VLAN

11.62  ED-VLAN-ETH

11.63  ED-WDMANS

11.64  ED-WDMSIDE

ED Commands

---

---

Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration. Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's path protection feature, which may be used in any topological network configuration. Cisco does not recommend using its path protection feature in any particular topological network configuration.

---

This chapter provides edit (ED) commands for the Cisco ONS 15454, Cisco ONS 15310-CL, Cisco ONS 15310-MA, and Cisco ONS 15600.

11.1  ED-<GIGE_TYPE>

(Cisco ONS 15454 and ONS 15600) The Edit 10GIGE or GIGE (ED-<GIGE_TYPE>) command edits Ethernet facility attributes. See Table 28-1 on page 28-1 for supported modifiers by platform.

Usage Guidelines

The default values for all optional parameters are network element (NE) default values. These values might not be the current value for a parameter. Use a retrieve command to obtain the current value.

The user can change the service state of a facility to OOS-MA OR DSBLD, only if all the following conditions are met

•The facility is not sourcing a synchronization clock

•The facility's DCC is disabled.

•The facility is not part of a protection group

•The facility is not supporting cross-connects

---

Note The conditions stipulated can be overridden by using the CMDMDE=FRCD option. The FRCD option will immediately remove the facility from service with no consideration for orderly interruption. Do not use in scripts or automated batch operations.

---

---

Note To completely disable the CMDMDE=FRCD option, provision the <to be defined parameter> in the NE defaults to FALSE. This will prevent the FRCD option from being honored by the NE. The NE default parameter can be provisioned using the CTC only.

---

---

Note The following parameters apply only to ED-GIGE; ADMINSTATE, LINKSTATE, MTU, FLOWCTRL, AUTONEG, HIWMRK, LOWMRK, DUPLEX, SPEED, and SOAK.

---

---

Note The MACADDR parameter is applicable for ED-10GIGE only.

---

---

Note The LIENABLE and LITIMER parameters are applicable only to CE-1000 card.

---

Category

Ports

Security

Provisioning

Input Format

ED-<GIGE_TYPE>:[<TID>]:<AID>:<CTAG>:::[ADMINSTATE=<ADMINSTATE>],
[LINKSTATE=<LINKSTATE>],[MTU=<MTU>],[FLOWCTRL=<FLOWCTRL>],
[AUTONEG=<AUTONEG>],[HIWMRK=<HIWMRK>],[LOWMRK=<LOWMRK>],
[OPTICS=<OPTICS>],[DUPLEX=<DUPLEX>],[SPEED=<SPEED>],[NAME=<NAME>],
[CMDMDE=<CMDMDE>],[MACADDR=<MACADDR>],[FREQ=<FREQ>],[LOSSB=<LOSSB>],
[SOAK=<SOAK>],[LIENABLE=<LIENABLE>],[LITIMER=<LITIMER>]:[<PST>[,<SST>]];

Input Example

ED-GIGE:PETALUMA:FAC-1-1:123:::ADMINSTATE=DOWN,LINKSTATE=DOWN,MTU=1548,
FLOWCTRL=NONE,AUTONEG=Y,HIWMRK=485,LOWMRK=25,OPTICS=1000_BASE_LX,
DUPLEX=AUTO,SPEED=AUTO,NAME="GIGE PORT",CMDMDE=FRCD,
MACADDR=00-0E-AA-BB-CC-FF,FREQ=1550,LOSSB=SX,SOAK=32,LIENABLE=Y,
LITIMER=200:IS,AINS;

Input Parameters

<AID>	Access identifier from the "26.15  FACILITY" section on page 26-34.
<ADMINSTATE>	Administration type. The parameter type is UP_DOWN, which indicates an up or down value.
•DOWN	Down
•UP	Up
<LINKSTATE>	Link state. The parameter type is UP_DOWN, which indicates an up or down value.
•DOWN	Down
•UP	Up
<MTU>	Maximum transport unit. The parameter type is MTU_TYPE which indicates the maximum transport unit used by an Ethernet card. Defaults to 9600.
•10004	10004. Indicates jumbo size.
•1500	1500
•1548	1548
•9600	9600. Indicates the jumbo size.
•64	64
•9700	9700. Indicates the jumbo size.
<FLOWCTRL>	Flow control. The parameter is FLOW which indicates the type of flow control that has been negotiated for an Ethernet port. Defaults to NONE.
•ASYMMETRIC	Asymmetric flow control
•ASYMMETRIC_LOCAL	Asymmetric local flow control
•NONE	No flow control
•PASSTHRU	Passthrough flow control
•SYMMETRIC	Symmetric flow control
<AUTONEG>	Autonegotiation. The parameter is ON_OFF which disables or enables an attribute. Defaults to Y.
•N	Disable an attribute
•Y	Enable an attribute
<HIWMRK>	High water mark. Integer. Defaults to 485.
<LOWMRK>	Low water mark. Integer. Defaults to 25.
<OPTICS>	The parameter is OPTICS which indicates the type of Gigabyte Ethernet optics being used.
•1000_BASE_CX	1000 Base CX
•1000_BASE_LX	1000 Base LX
•1000_BASE_SX	1000 Base SX
•1000_BASE_T	1000BaseT
•1000_BASE_ZX	1000 Base ZX
•100_BASE_BX_D	100BaseBX_D
•100_BASE_BX_U	100BaseBX_U
•100_BASE_FX	100 Base FX
•100_BASE_LX	100 Base LX
•CWDM_1470	Coarse wavelength division multiplexing (CWDM) 1470
•CWDM_1490	CWDM 1490
•CWDM_1510	CWDM 1510
•CWDM_1530	CWDM 1530
•CWDM_1550	CWDM 1550
•CWDM_1570	CWDM 1570
•CWDM_1590	CWDM 1590
•CWDM_1610	CWDM 1610
•ITU_100G_1530_33	ITU-100G 1530.33
•ITU_100G_1531_12	ITU-100G 1531.12
•ITU_100G_1531_90	ITU-100G 1531.90
•ITU_100G_1532_68	ITU-100G 1532.68
•ITU_100G_1534_25	ITU-100G 1534.25
•ITU_100G_1535_04	ITU-100G 1535.04
•ITU_100G_1535_82	ITU-100G 1535.82
•ITU_100G_1536_61	ITU-100G 1536.61
•ITU_100G_1538_19	ITU-100G 1538.19
•ITU_100G_1538_98	ITU-100G 1538.98
•ITU_100G_1539_77	ITU-100G 1539.77
•ITU_100G_1540_56	ITU-100G 1540.56
•ITU_100G_1542_14	ITU-100G 1542.14
•ITU_100G_1542_94	ITU-100G 1542.94
•ITU_100G_1543_73	ITU-100G 1543.73
•ITU_100G_1544_53	ITU-100G 1544.53
•ITU_100G_1546_12	ITU-100G 1546.12
•ITU_100G_1546_92	ITU-100G 1546.92
•ITU_100G_1547_72	ITU-100G 1547.72
•ITU_100G_1548_51	ITU-100G 1548.51
•ITU_100G_1550_12	ITU-100G 1550.12
•ITU_100G_1550_92	ITU-100G 1550.92
•ITU_100G_1551_72	ITU-100G 1551.72
•ITU_100G_1552_52	ITU-100G 1552.52
•ITU_100G_1554_13	ITU-100G 1554.13
•ITU_100G_1554_94	ITU-100G 1554.94
•ITU_100G_1555_75	ITU-100G 1555.75
•ITU_100G_1556_55	ITU-100G 156.55
•ITU_100G_1558_17	ITU-100G 1558.17
•ITU_100G_1558_98	ITU-100G 1558.98
•ITU_100G_1559_79	ITU-100G 1559.79
•ITU_100G_1560_61	ITU-100G 1560.61
•UNKNOWN	Unknown
•UNPLUGGED	Unplugged
<DUPLEX>	The parameter is ETHER_DUPLEX which indicates duplex mode. Defaults to AUTO.
•AUTO	Auto mode
•FULL	Full mode
•HALF	Half mode
<SPEED>	The parameter type is ETHER_SPEED which indicates Ethernet speed. Defaults to AUTO.
•100_MBPS	100 Megabits per seconds
•10_GBPS	10 Gigabits per second
•10_MBPS	10 Megabits per second
•1_GBPS	1 Gigabit per second
•AUTO	Automatic
<NAME>	Port name. NAME is a string. Defaults to NULL. Maximum length is 32 characters.
<CMDMDE>	The parameter type is command mode (CMDMDE). Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in IS-NR or OOS-AU,AINS service states.
•FRCD	Force the system to override a state where the command would normally be denied.
•NORM	Execute the command normally. Do not override any conditions that might make the command fail.
<MACADDR>	MACADDR is a string. Defaults to NULL. Maximum length is 18 characters.
<FREQ>	The parameter type is OPTICAL_WLEN which indicates the optical wavelength.
•1310	Wavelength 1310
•1470	Wavelength 1470
•1490	Wavelength 1490
•1510	Wavelength 1510
•1529.55	Wavelength 1529.55
•1529.94	Wavelength 1529.94
•1530	Wavelength 1530
•1530.33	Wavelength 1530.33
•1530.73	Wavelength 1530.73
•1531.12	Wavelength 1531.12
•1531.51	Wavelength 1531.51
•1531.90	Wavelength 1531.90
•1532.29	Wavelength 1532.29
•1532.68	Wavelength 1532.68
•1533.07	Wavelength 1533.07
•1533.47	Wavelength 1533.47
•1533.86	Wavelength 1533.86
•1534.25	Wavelength 1534.25
•1534.64	Wavelength 1534.64
•1535.04	Wavelength 1535.04
•1535.43	Wavelength 1535.43
•1535.82	Wavelength 1535.82
•1536.22	Wavelength 1536.22
•1536.61	Wavelength 1536.61
•1537	Wavelength 1537
•1537.40	Wavelength 1537.40
•1537.79	Wavelength 1537.79
•1538.19	Wavelength 1538.19
•1538.58	Wavelength 1538.58
•1538.98	Wavelength 1538.98
•1539.37	Wavelength 1539.37
•1539.77	Wavelength 1539.77
•1540.16	Wavelength 1540.16
•1540.56	Wavelength 1540.56
•1540.95	Wavelength 1540.95
•1541.35	Wavelength 1541.35
•1541.75	Wavelength 1541.75
•1542.14	Wavelength 1542.14
•1542.35	Wavelength 1542.35
•1542.54	Wavelength 1542.54
•1542.94	Wavelength 1542.94
•1543.33	Wavelength 1543.33
•1543.73	Wavelength 1543.73
•1544.13	Wavelength 1544.13
•1544.53	Wavelength 1544.53
•1544.92	Wavelength 1544.92
•1545.32	Wavelength 1545.32
•1545.72	Wavelength 1545.72
•1546.12	Wavelength 1546.12
•1546.52	Wavelength 1546.52
•1546.92	Wavelength 1546.92
•1547.32	Wavelength 1547.32
•1547.72	Wavelength 1547.72
•1548.12	Wavelength 1548.12
•1548.51	Wavelength 1548.51
•1548.92	Wavelength 1548.92
•1549.32	Wavelength 1549.32
•1549.71	Wavelength 1549.71
•1550	Wavelength 1500
•1550.12	Wavelength 1550.12
•1550.52	Wavelength 1550.52
•1550.92	Wavelength 1550.92
•1551.32	Wavelength 1551.32
•1551.72	Wavelength 1551.72
•1552.12	Wavelength 1552.12
•1552.52	Wavelength 1552.52
•1552.93	Wavelength 1552.93
•1553.33	Wavelength 1553.33
•1553.73	Wavelength 1553.73
•1554.13	Wavelength 1554.13
•1554.13	Wavelength 1554.13
•1554.94	Wavelength 1554.94
•1555.34	Wavelength 1555.34
•1555.75	Wavelength 1555.75
•1556.15	Wavelength 1556.15
•1556.55	Wavelength 1556.55
•1556.96	Wavelength 1556.96
•1557.36	Wavelength 1557.36
•1557.77	Wavelength 1557.77
•1558.17	Wavelength 1558.17
•1558.58	Wavelength 1558.58
•1558.98	Wavelength 1558.98
•1559.39	Wavelength 1559.39
•1559.79	Wavelength 1559.79
•1560.20	Wavelength 1560.20
•1560.61	Wavelength 1560.61
•1561.01	Wavelength 1561.01
•1561.42	Wavelength 1561.42
•1561.83	Wavelength 1561.83
•1570	Wavelength 1570
•1570.83	Wavelength 1570.83
•1571.24	Wavelength 1571.24
•1571.65	Wavelength 1571.65
•1572.06	Wavelength 1572.06
•1572.48	Wavelength 1572.48
•1572.89	Wavelength 1572.89
•1573.30	Wavelength 1573.30
•1573.71	Wavelength 1573.71
•1574.13	Wavelength 1574.13
•1574.54	Wavelength 1574.54
•1574.95	Wavelength 1574.95
•1575.37	Wavelength 1575.37
•1575.78	Wavelength 1575.78
•1576.20	Wavelength 1576.20
•1576.61	Wavelength 1576.61
•1577.03	Wavelength 1577.03
•1577.44	Wavelength 1577.44
•1577.86	Wavelength 1577.86
•1578.27	Wavelength 1578.27
•1578.69	Wavelength 1578.69
•1579.10	Wavelength 1579.10
•1579.52	Wavelength 1579.52
•1579.93	Wavelength 1579.93
•1580.35	Wavelength 1580.35
•1580.77	Wavelength 1580.77
•1581.18	Wavelength 1581.18
•1581.60	Wavelength 1581.60
•1582.02	Wavelength 1582.02
•1582.44	Wavelength 1582.44
•1582.85	Wavelength 1582.85
•1583.27	Wavelength 1583.27
•1583.69	Wavelength 1583.69
•1584.11	Wavelength 1584.11
•1584.53	Wavelength 1584.53
•1584.95	Wavelength 1584.95
•1585.36	Wavelength 1585.36
•1585.78	Wavelength 1585.78
•1586.20	Wavelength 1586.20
•1586.62	Wavelength 1586.62
•1587.04	Wavelength 1587.04
•1587.46	Wavelength 1587.46
•1587.88	Wavelength 1587.88
•1588.30	Wavelength 1588.30
•1588.73	Wavelength 1588.73
•1589.15	Wavelength 1589.15
•1589.57	Wavelength 1589.57
•1589.99	Wavelength 1589.99
•1590	Wavelength 1590
•1590.41	Wavelength 1590.41
•1590.83	Wavelength 1590.83
•1591.26	Wavelength 1591.26
•1591.68	Wavelength 1591.68
•1592.10	Wavelength 1592.10
•1592.52	Wavelength 1592.52
•1592.95	Wavelength 1592.95
•1593.37	Wavelength 1593.37
•1593.79	Wavelength 1593.79
•1594.22	Wavelength 1594.22
•1594.64	Wavelength 1594.64
•1595.06	Wavelength 1595.06
•1595.49	Wavelength 1595.49
•1596.34	Wavelength 1596.34
•1596.76	Wavelength 1596.76
•1597.19	Wavelength 1597.19
•1597.62	Wavelength 1597.62
•1598.04	Wavelength 1598.04
•1598.47	Wavelength 1598.47
•1598.89	Wavelength 1598.89
•1599.32	Wavelength 1599.32
•1599.75	Wavelength 1599.75
•1600.06	Wavelength 1600.06
•1601.03	Wavelength 1601.03
•1601.46	Wavelength 1601.46
•1601.88	Wavelength 1601.88
•1602.31	Wavelength 1602.31
•1602.74	Wavelength 1602.74
•1603.17	Wavelength 1603.17
•1603.60	Wavelength 1603.60
•1604.03	Wavelength 1604.03
•1610	Wavelength 1610
•USE-TWL1	Use Tunable Wavelength 1
<LOSSB>	The parameter type is REACH which indicates the reach values.
•AUTOPROV	Autoprovisioning
•CX	Reach CX
•DX	Reach DX
•HX	Reach HX
•I1	Reach I1
•IR-1	Reach IR-1
•IR-2	Reach IR-2
•L1	Reach L1
•L2	Reach L2
•L3	Reach L3
•LR-1	Reach LR-1
•LR-2	Reach LR-2
•LR-3	Reach LR-3
•LX	Reach LX
•S1	Reach S1
•S2	Reach S2
•SR	Reach SR
•SR-1	Reach SR-1
•SX	Reach SX
•T	Reach T
•VX	Reach VX
•ZX	Reach ZX
<SOAK>	IS-AINS to IS transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer. Defaults to 32.
<LIENABLE>	(Optional) Enable or disable link integrity timer. Takes either Y or N. Value Y enables the LITIMER and value N disbales LITIMER. By default LITIMER is enabled.
<LITIMER>	(Optional) Link integrity timer duration in the range between 200 ms and 5000 ms in the multiples of 100 ms.
<PST>	The primary state. The parameter type is PST, which indicates the current overall service condition of an entity. Defaults to OOS.
•IS	In service
•OOS	Out of service
SST	The secondary state. The parameter type is SST, which provides additional information pertaining to PST and primary state qualifier (PSTQ). Defaults to DSBLD.
•AINS	Automatic in service
•DSBLD	Disabled
•LPBK	Loopback
•MEA	Mismatch of equipment and attributes
•MT	Maintenance mode
•OOG	Out of group
•SWDL	Software downloading
•UAS	Unassigned
•UEQ	Unequipped

11.2  ED-<MOD1FCPAYLOAD>

(Cisco ONS 15454) The Edit 1GISC3, 2GISC3, D1VIDEO, DV6000, ESCON, ETRCLO, HDTV or PASSTHRU (ED-<MODFCPAYLOAD>) command edits the attributes related to the Fibre Channel (FC) facility. The state IS,AINS is not supported on the FC port. See Table 28-1 on page 28-1 for supported modifiers by platform.

Usage Guidelines

The user can change the service state of a facility to locked-enabled or disabled, only if all the following conditions are met

•The facility is not sourcing a synchronization clock

•The facility's DCC is disabled.

•The facility is not part of a protection group

•The facility is not supporting cross-connects

---

Note The conditions stipulated can be overridden by using the CMDMDE=FRCD option. The FRCD option will immediately remove the facility from service with no consideration for orderly interruption. Do not use in scripts or automated batch operations.

---

---

Note To completely disable the CMDMDE=FRCD option, provision the <to be defined parameter> in the NE defaults to FALSE. This will prevent the FRCD option from being honored by the NE. The NE default parameter can be provisioned using the CTC only.

---

---

Note•The port parameters VIZ, LINKRCVRY, DISTEXTN, AUTODETECTION, LINKCREDITS, and MFS can be edited only if the port state is OOS,MT or OOS,DSBLD.

•The port parameters AUTODETECTION, LINKCREDITS, and MFS can be edited only if distance extension is enabled (set to B2B).

•When 1GFICON and 2GFICON payloads are provisioned, distance extension=B2B is the default and only valid setting. Setting distance extension (using the ED-nGFICON command) to any other setting will be denied with an error message, for example, Provisioning Rules Failed.

---

Category

Ports

Security

Provisioning

Input Format

ED-<MOD1FCPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[LINKRCVRY=<LINKRCVRY>],[DISTEXTN= <DISTANCE_EXTENSION>],[AUTODETECTION=<AUTO_DETECTION>], [LINKCREDITS=<CREDITS>],[FASTSWITCH=<FASTSWITCH>],[MFS=<MAXFRMSIZE>] ,[NAME=<NAME>],[CMDMDE=<CMDMDE>],[SOAK=<SOAK>],[FREQ=<FREQ>], [LOSSB=<LOSSB>],[SQUELCH=<SQUELCH>][:<PST>[,<SST>]];

Input Example

ED-1GFC:PETALUMA:FAC-6-1:1:::LINKRCVRY=Y,DISTEXTN=NONE,AUTODETECTION=Y,
LINKCREDITS=10,FASTWITCH= ,MFS=2148,NAME="FC PORT",CMDMDE=CMDMDE,SOAK=32,
FREQ=1550,LOSSB=LR-1:OOS,MT;

Input Parameters

<AID>	Access identifier from the "26.15  FACILITY" section on page 26-34.
<LINKRCVRY>	Link recovery. The parameter type is ON_OFF, which disables or enables an attribute.
•N	Disable an attribute.
•Y	Enable an attribute.
<DISTEXTN>	Distance extension. It can be set to Buffer-to-Buffer (B2B) Credit Management state or None. Note B2B and link recovery are mutually exclusive. You cannot turn on both B2B and link recovery at the same time. The parameter type is DISTANCE_EXTENSION (distance extension).
•B2B	Buffer to buffer flow control
•NONE	No distance extension
<AUTODETECTION>	Autodetection. Turns autodetection on or off. The parameter type is ON_OFF, which disables or enables an attribute.
•N	Disable an attribute
•Y	Enable an attribute
<LINKCREDITS>	Number of link credits. If autodetection is set to off, the value of the link credits will be used to configure the hardware. LINKCREDITS is an integer.
<FASTSWITCH>	When Fast Switchover is ON switchover must be less than 150 ms. In case of client Failure Fast Switchover is not supported. This switch time is achieved for fc1g/fc2g/fc4g traffic for trunk failures and manual/forced/lockout switches only. The parameter type is ON_OFF, which disables or enables an attribute.
•N	Disable an attribute.
•Y	Enable an attribute.
<MFS>	Maximum frame size. MFS is an integer.
<NAME>	String. User-assigned port name.
<CMDMDE>	The parameter type is command mode (CMDMDE). Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in IS-NR or OOS-AU,AINS service states.
•FRCD	Force the system to override a state where the command would normally be denied.
•NORM	Execute the command normally. Do not override any conditions that might make the command fail.
<SOAK>	OOS-AINS to IS transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer.
<FREQ>	The parameter type is OPTICAL_WLEN, which is the optical wavelength.
•1310	Wavelength 1310
•1470	Wavelength 1470
•1490	Wavelength 1490
•1510	Wavelength 1510
•1529.55	Wavelength 1529.55
•1529.94	Wavelength 1529.94
•1530	Wavelength 1530
•1530.33	Wavelength 1530.33
•1530.73	Wavelength 1530.73
•1531.12	Wavelength 1531.12
•1531.51	Wavelength 1531.51
•1531.90	Wavelength 1531.90
•1532.29	Wavelength 1532.29
•1532.68	Wavelength 1532.68
•1533.07	Wavelength 1533.07
•1533.47	Wavelength 1533.47
•1533.86	Wavelength 1533.86
•1534.25	Wavelength 1534.25
•1534.64	Wavelength 1534.64
•1535.04	Wavelength 1535.04
•1535.43	Wavelength 1535.43
•1535.82	Wavelength 1535.82
•1536.22	Wavelength 1536.22
•1536.61	Wavelength 1536.61
•1537	Wavelength 1537
•1537.40	Wavelength 1537.40
•1537.79	Wavelength 1537.79
•1538.19	Wavelength 1538.19
•1538.58	Wavelength 1538.58
•1538.98	Wavelength 1538.98
•1539.37	Wavelength 1539.37
•1539.77	Wavelength 1539.77
•1540.16	Wavelength 1540.16
•1540.56	Wavelength 1540.56
•1540.95	Wavelength 1540.95
•1541.35	Wavelength 1541.35
•1541.75	Wavelength 1541.75
•1542.14	Wavelength 1542.14
•1542.35	Wavelength 1542.35
•1542.54	Wavelength 1542.54
•1542.94	Wavelength 1542.94
•1543.33	Wavelength 1543.33
•1543.73	Wavelength 1543.73
•1544.13	Wavelength 1544.13
•1544.53	Wavelength 1544.53
•1544.92	Wavelength 1544.92
•1545.32	Wavelength 1545.32
•1545.72	Wavelength 1545.72
•1546.12	Wavelength 1546.12
•1546.52	Wavelength 1546.52
•1546.92	Wavelength 1546.92
•1547.32	Wavelength 1547.32
•1547.72	Wavelength 1547.72
•1548.12	Wavelength 1548.12
•1548.51	Wavelength 1548.51
•1548.92	Wavelength 1548.92
•1549.32	Wavelength 1549.32
•1549.71	Wavelength 1549.71
•1550	Wavelength 1500
•1550.12	Wavelength 1550.12
•1550.52	Wavelength 1550.52
•1550.92	Wavelength 1550.92
•1551.32	Wavelength 1551.32
•1551.72	Wavelength 1551.72
•1552.12	Wavelength 1552.12
•1552.52	Wavelength 1552.52
•1552.93	Wavelength 1552.93
•1553.33	Wavelength 1553.33
•1553.73	Wavelength 1553.73
•1554.13	Wavelength 1554.13
•1554.13	Wavelength 1554.13
•1554.94	Wavelength 1554.94
•1555.34	Wavelength 1555.34
•1555.75	Wavelength 1555.75
•1556.15	Wavelength 1556.15
•1556.55	Wavelength 1556.55
•1556.96	Wavelength 1556.96
•1557.36	Wavelength 1557.36
•1557.77	Wavelength 1557.77
•1558.17	Wavelength 1558.17
•1558.58	Wavelength 1558.58
•1558.98	Wavelength 1558.98
•1559.39	Wavelength 1559.39
•1559.79	Wavelength 1559.79
•1560.20	Wavelength 1560.20
•1560.61	Wavelength 1560.61
•1561.01	Wavelength 1561.01
•1561.42	Wavelength 1561.42
•1561.83	Wavelength 1561.83
•1570	Wavelength 1570
•1570.83	Wavelength 1570.83
•1571.24	Wavelength 1571.24
•1571.65	Wavelength 1571.65
•1572.06	Wavelength 1572.06
•1572.48	Wavelength 1572.48
•1572.89	Wavelength 1572.89
•1573.30	Wavelength 1573.30
•1573.71	Wavelength 1573.71
•1574.13	Wavelength 1574.13
•1574.54	Wavelength 1574.54
•1574.95	Wavelength 1574.95
•1575.37	Wavelength 1575.37
•1575.78	Wavelength 1575.78
•1576.20	Wavelength 1576.20
•1576.61	Wavelength 1576.61
•1577.03	Wavelength 1577.03
•1577.44	Wavelength 1577.44
•1577.86	Wavelength 1577.86
•1578.27	Wavelength 1578.27
•1578.69	Wavelength 1578.69
•1579.10	Wavelength 1579.10
•1579.52	Wavelength 1579.52
•1579.93	Wavelength 1579.93
•1580.35	Wavelength 1580.35
•1580.77	Wavelength 1580.77
•1581.18	Wavelength 1581.18
•1581.60	Wavelength 1581.60
•1582.02	Wavelength 1582.02
•1582.44	Wavelength 1582.44
•1582.85	Wavelength 1582.85
•1583.27	Wavelength 1583.27
•1583.69	Wavelength 1583.69
•1584.11	Wavelength 1584.11
•1584.53	Wavelength 1584.53
•1584.95	Wavelength 1584.95
•1585.36	Wavelength 1585.36
•1585.78	Wavelength 1585.78
•1586.20	Wavelength 1586.20
•1586.62	Wavelength 1586.62
•1587.04	Wavelength 1587.04
•1587.46	Wavelength 1587.46
•1587.88	Wavelength 1587.88
•1588.30	Wavelength 1588.30
•1588.73	Wavelength 1588.73
•1589.15	Wavelength 1589.15
•1589.57	Wavelength 1589.57
•1589.99	Wavelength 1589.99
•1590	Wavelength 1590
•1590.41	Wavelength 1590.41
•1590.83	Wavelength 1590.83
•1591.26	Wavelength 1591.26
•1591.68	Wavelength 1591.68
•1592.10	Wavelength 1592.10
•1592.52	Wavelength 1592.52
•1592.95	Wavelength 1592.95
•1593.37	Wavelength 1593.37
•1593.79	Wavelength 1593.79
•1594.22	Wavelength 1594.22
•1594.64	Wavelength 1594.64
•1595.06	Wavelength 1595.06
•1595.49	Wavelength 1595.49
•1596.34	Wavelength 1596.34
•1596.76	Wavelength 1596.76
•1597.19	Wavelength 1597.19
•1597.62	Wavelength 1597.62
•1598.04	Wavelength 1598.04
•1598.47	Wavelength 1598.47
•1598.89	Wavelength 1598.89
•1599.32	Wavelength 1599.32
•1599.75	Wavelength 1599.75
•1600.06	Wavelength 1600.06
•1601.03	Wavelength 1601.03
•1601.46	Wavelength 1601.46
•1601.88	Wavelength 1601.88
•1602.31	Wavelength 1602.31
•1602.74	Wavelength 1602.74
•1603.17	Wavelength 1603.17
•1603.60	Wavelength 1603.60
•1604.03	Wavelength 1604.03
•1610	Wavelength 1610
•USE-TWL1	Use Tunable Wavelength 1
<LOSSB>	The parameter type is REACH, which is the reach value.
•AUTOPROV	Autoprovisioning
•CX	Reach CX
•DX	Reach DX
•HX	Reach HX
•I1	Reach I1
•IR-1	Reach IR-1
•IR-2	Reach IR-2
•L1	Reach L1
•L2	Reach L2
•L3	Reach L3
•LR-1	Reach LR-1
•LR-2	Reach LR-2
•LR-3	Reach LR-3
•LX	Reach LX
•S1	Reach S1
•S2	Reach S2
•SR	Reach SR
•SR-1	Reach SR-1
•SX	Reach SX
•T	Reach T
•VX	Reach VX
•ZX	Reach ZX
<PST>	Primary state. the parameter type is PST, which indicates the current overall service condition of an entity.
•IS	In service
•OOS	Out of service
<SST>	Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•AINS	Automatic in service
•DSBLD	Disabled
•LPBK	Loopback
•MEA	Mismatch of equipment and attributes
•MT	Maintenance mode
•OOG	Out of group
•SWDL	Software downloading
•UAS	Unassigned
•UEQ	Unequipped

11.3  ED-<MOD1FICONPAYLOAD>

(Cisco ONS 15454) The Edit 1GFICON, 2GFICON, 4GFICON, or ESCON (ED-<MOD1FICONPAYLOAD>) command edits the attributes related with the fiber connectivity (FICON) payload facility. The state IS,AINS is not supported on the FICON port.

Usage Guidelines

See Table 28-1 on page 28-1 for supported modifiers by platform.

Category

Ports

Security

Provisioning

Input Format

ED-<MOD1FICONPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[LINKRCVRY=<LINKRCVRY>],[DISTEXTN= <DISTANCE_EXTENSION>],[AUTODETECTION=<AUTO_DETECTION>], [LINKCREDITS=<CREDITS>],[FASTSWITCH=<FASTSWITCH>],[MFS=<MAXFRMSIZE>] ,[NAME=<NAME>],[CMDMDE=<CMDMDE>],[SOAK=<SOAK>],[FREQ=<FREQ>], [LOSSB=<LOSSB>],[SQUELCH=<SQUELCH>][:<PST>[,<SST>]];

Input Example

ED-1GFICON:PETALUMA:FAC-6-1:1:::LINKRCVRY=Y,DISTEXTN=NONE,
AUTODETECTION=Y, LINKCREDITS=10, FASTSWITCH= ,MFS=2148,NAME="FCPORT",CMDMDE=CMDMDE,
SOAK=32,FREQ=1550,LOSSB=LR-1:OOS,MT;

Input Parameters

<AID>	Access identifier from the "26.15  FACILITY" section on page 26-34.
<LINKRCVRY>	Link recovery. The parameter type is ON_OFF, which disables or enables an attribute.
•N	Disable an attribute
•Y	Enable an attribute
<DISTEXTN>	Distance extension. It can be set to B2B Credit Management state or None. Note B2B and link recovery are mutually exclusive. You cannot turn on both B2B and link recovery at the same time. The parameter type is DISTANCE_EXTENSION (distance extension).
•B2B	Buffer-to-buffer flow control
•NONE	No distance extension
<AUTODETECTION>	Autodetection. Turns autodetection on or off. The parameter type is ON_OFF, which disables or enables an attribute.
•N	Disable an attribute
•Y	Enable an attribute
<LINKCREDITS>	Number of link credits. If autodetection is set to off the value of the link credits will be used to configure the hardware. LINKCREDITS is an integer.
<FASTSWITCH>	When Fast Switchover is ON switchover must be less than 150 ms. In case of client Failure Fast Switchover is not supported. This switch time is achieved for fc1g/fc2g/fc4g traffic for trunk failures and manual/forced/lockout switches only. The parameter type is ON_OFF, which disables or enables an attribute.
•N	Disable an attribute.
•Y	Enable an attribute.
<MFS>	Maximum frame size. MFS is an integer.
<NAME>	String. User-assigned port name.
<CMDMDE>	The parameter type is command mode (CMDMDE). Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in IS-NR or OOS-AU,AINS service states.
•FRCD	Force the system to override a state where the command would normally be denied.
•NORM	Execute the command normally. Do not override any conditions that might make the command fail.
<SOAK>	OOS-AINS to IS transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). SOAK is an integer.
<FREQ>	The parameter type is OPTICAL_WLEN (optical wavelength).
•1310	Wavelength 1310
•1470	Wavelength 1470
•1490	Wavelength 1490
•1510	Wavelength 1510
•1529.55	Wavelength 1529.55
•1529.94	Wavelength 1529.94
•1530	Wavelength 1530
•1530.33	Wavelength 1530.33
•1530.73	Wavelength 1530.73
•1531.12	Wavelength 1531.12
•1531.51	Wavelength 1531.51
•1531.90	Wavelength 1531.90
•1532.29	Wavelength 1532.29
•1532.68	Wavelength 1532.68
•1533.07	Wavelength 1533.07
•1533.47	Wavelength 1533.47
•1533.86	Wavelength 1533.86
•1534.25	Wavelength 1534.25
•1534.64	Wavelength 1534.64
•1535.04	Wavelength 1535.04
•1535.43	Wavelength 1535.43
•1535.82	Wavelength 1535.82
•1536.22	Wavelength 1536.22
•1536.61	Wavelength 1536.61
•1537	Wavelength 1537
•1537.40	Wavelength 1537.40
•1537.79	Wavelength 1537.79
•1538.19	Wavelength 1538.19
•1538.58	Wavelength 1538.58
•1538.98	Wavelength 1538.98
•1539.37	Wavelength 1539.37
•1539.77	Wavelength 1539.77
•1540.16	Wavelength 1540.16
•1540.56	Wavelength 1540.56
•1540.95	Wavelength 1540.95
•1541.35	Wavelength 1541.35
•1541.75	Wavelength 1541.75
•1542.14	Wavelength 1542.14
•1542.35	Wavelength 1542.35
•1542.54	Wavelength 1542.54
•1542.94	Wavelength 1542.94
•1543.33	Wavelength 1543.33
•1543.73	Wavelength 1543.73
•1544.13	Wavelength 1544.13
•1544.53	Wavelength 1544.53
•1544.92	Wavelength 1544.92
•1545.32	Wavelength 1545.32
•1545.72	Wavelength 1545.72
•1546.12	Wavelength 1546.12
•1546.52	Wavelength 1546.52
•1546.92	Wavelength 1546.92
•1547.32	Wavelength 1547.32
•1547.72	Wavelength 1547.72
•1548.12	Wavelength 1548.12
•1548.51	Wavelength 1548.51
•1548.92	Wavelength 1548.92
•1549.32	Wavelength 1549.32
•1549.71	Wavelength 1549.71
•1550	Wavelength 1500
•1550.12	Wavelength 1550.12
•1550.52	Wavelength 1550.52
•1550.92	Wavelength 1550.92
•1551.32	Wavelength 1551.32
•1551.72	Wavelength 1551.72
•1552.12	Wavelength 1552.12
•1552.52	Wavelength 1552.52
•1552.93	Wavelength 1552.93
•1553.33	Wavelength 1553.33
•1553.73	Wavelength 1553.73
•1554.13	Wavelength 1554.13
•1554.13	Wavelength 1554.13
•1554.94	Wavelength 1554.94
•1555.34	Wavelength 1555.34
•1555.75	Wavelength 1555.75
•1556.15	Wavelength 1556.15
•1556.55	Wavelength 1556.55
•1556.96	Wavelength 1556.96
•1557.36	Wavelength 1557.36
•1557.77	Wavelength 1557.77
•1558.17	Wavelength 1558.17
•1558.58	Wavelength 1558.58
•1558.98	Wavelength 1558.98
•1559.39	Wavelength 1559.39
•1559.79	Wavelength 1559.79
•1560.20	Wavelength 1560.20
•1560.61	Wavelength 1560.61
•1561.01	Wavelength 1561.01
•1561.42	Wavelength 1561.42
•1561.83	Wavelength 1561.83
•1570	Wavelength 1570
•1570.83	Wavelength 1570.83
•1571.24	Wavelength 1571.24
•1571.65	Wavelength 1571.65
•1572.06	Wavelength 1572.06
•1572.48	Wavelength 1572.48
•1572.89	Wavelength 1572.89
•1573.30	Wavelength 1573.30
•1573.71	Wavelength 1573.71
•1574.13	Wavelength 1574.13
•1574.54	Wavelength 1574.54
•1574.95	Wavelength 1574.95
•1575.37	Wavelength 1575.37
•1575.78	Wavelength 1575.78
•1576.20	Wavelength 1576.20
•1576.61	Wavelength 1576.61
•1577.03	Wavelength 1577.03
•1577.44	Wavelength 1577.44
•1577.86	Wavelength 1577.86
•1578.27	Wavelength 1578.27
•1578.69	Wavelength 1578.69
•1579.10	Wavelength 1579.10
•1579.52	Wavelength 1579.52
•1579.93	Wavelength 1579.93
•1580.35	Wavelength 1580.35
•1580.77	Wavelength 1580.77
•1581.18	Wavelength 1581.18
•1581.60	Wavelength 1581.60
•1582.02	Wavelength 1582.02
•1582.44	Wavelength 1582.44
•1582.85	Wavelength 1582.85
•1583.27	Wavelength 1583.27
•1583.69	Wavelength 1583.69
•1584.11	Wavelength 1584.11
•1584.53	Wavelength 1584.53
•1584.95	Wavelength 1584.95
•1585.36	Wavelength 1585.36
•1585.78	Wavelength 1585.78
•1586.20	Wavelength 1586.20
•1586.62	Wavelength 1586.62
•1587.04	Wavelength 1587.04
•1587.46	Wavelength 1587.46
•1587.88	Wavelength 1587.88
•1588.30	Wavelength 1588.30
•1588.73	Wavelength 1588.73
•1589.15	Wavelength 1589.15
•1589.57	Wavelength 1589.57
•1589.99	Wavelength 1589.99
•1590	Wavelength 1590
•1590.41	Wavelength 1590.41
•1590.83	Wavelength 1590.83
•1591.26	Wavelength 1591.26
•1591.68	Wavelength 1591.68
•1592.10	Wavelength 1592.10
•1592.52	Wavelength 1592.52
•1592.95	Wavelength 1592.95
•1593.37	Wavelength 1593.37
•1593.79	Wavelength 1593.79
•1594.22	Wavelength 1594.22
•1594.64	Wavelength 1594.64
•1595.06	Wavelength 1595.06
•1595.49	Wavelength 1595.49
•1596.34	Wavelength 1596.34
•1596.76	Wavelength 1596.76
•1597.19	Wavelength 1597.19
•1597.62	Wavelength 1597.62
•1598.04	Wavelength 1598.04
•1598.47	Wavelength 1598.47
•1598.89	Wavelength 1598.89
•1599.32	Wavelength 1599.32
•1599.75	Wavelength 1599.75
•1600.06	Wavelength 1600.06
•1601.03	Wavelength 1601.03
•1601.46	Wavelength 1601.46
•1601.88	Wavelength 1601.88
•1602.31	Wavelength 1602.31
•1602.74	Wavelength 1602.74
•1603.17	Wavelength 1603.17
•1603.60	Wavelength 1603.60
•1604.03	Wavelength 1604.03
•1610	Wavelength 1610
•USE-TWL1	Use Tunable Wavelength 1
<LOSSB>	The parameter type is REACH, which is the reach value.
•AUTOPROV	Autoprovisioning
•CX	Reach CX
•DX	Reach DX
•HX	Reach HX
•I1	Reach I1
•IR-1	Reach IR-1
•IR-2	Reach IR-2
•L1	Reach L1
•L2	Reach L2
•L3	Reach L3
•LR-1	Reach LR-1
•LR-2	Reach LR-2
•LR-3	Reach LR-3
•LX	Reach LX
•S1	Reach S1
•S2	Reach S2
•SR	Reach SR
•SR-1	Reach SR-1
•SX	Reach SX
•T	Reach T
•VX	Reach VX
•ZX	Reach ZX
<PST>	Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.
•IS	In service
•OOS	Out of service
<SST>	Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•AINS	Automatic in service
•DSBLD	Disabled
•LPBK	Loopback
•MEA	Mismatch of equipment and attributes
•MT	Maintenance mode
•OOG	Out of group
•SWDL	Software downloading
•UAS	Unassigned
•UEQ	Unequipped

11.4  ED-<MOD2DWDMPAYLOAD>

(Cisco ONS 15454) The Edit 10GFC, 10GIGE, 1GFC, 1GFICON, 1GISC3, 2GFC, 2GFICON, 2GISC3, 4GFC, 4GFICON, D1VIDEO, DV6000, ESCON, ETRCLO, GIGE, HDTV, ISC3, or PASSTHRU (ED-<MOD2DWDMPAYLOAD>) command edits the operating parameters for a dense wavelength division multiplexing (DWDM) client facility.

Usage Guidelines

See Table 28-1 on page 28-1 for supported modifiers by platform.

Category

DWDM

Security

Provisioning

Input Format

ED-<MOD2DWDMPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[NAME=<NAME>],
[CMDMDE=<CMDMDE>],[FREQ=<FREQ>],[LOSSB=<LOSSB>]:[<PST>[,<SST>]];

Input Example

ED-HDTV::FAC-1-1:1:::NAME="PORTNAME",CMDMDE=CMDMDE,FREQ=1550,
LOSSB=LR-1:IS,AINS;

Input Parameters

<AID>	Access identifier from the "26.15  FACILITY" section on page 26-34.
<LINKCREDITS>	Number of link credits. If autodetection is set to off the value of the link credits will be used to configure the hardware. LINKCREDITS is an integer.
<NAME>	String. User-assigned port name.
<CMDMDE>	The parameter type is command mode (CMDMDE). Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in IS-NR or OOS-AU,AINS service states.
•FRCD	Force the system to override a state where the command would normally be denied.
•NORM	Execute the command normally. Do not override any conditions that might make the command fail.
<FREQ>	The parameter type is OPTICAL_WLEN (optical wavelength).
•1310	Wavelength 1310
•1470	Wavelength 1470
•1490	Wavelength 1490
•1510	Wavelength 1510
•1529.55	Wavelength 1529.55
•1529.94	Wavelength 1529.94
•1530	Wavelength 1530
•1530.33	Wavelength 1530.33
•1530.73	Wavelength 1530.73
•1531.12	Wavelength 1531.12
•1531.51	Wavelength 1531.51
•1531.90	Wavelength 1531.90
•1532.29	Wavelength 1532.29
•1532.68	Wavelength 1532.68
•1533.07	Wavelength 1533.07
•1533.47	Wavelength 1533.47
•1533.86	Wavelength 1533.86
•1534.25	Wavelength 1534.25
•1534.64	Wavelength 1534.64
•1535.04	Wavelength 1535.04
•1535.43	Wavelength 1535.43
•1535.82	Wavelength 1535.82
•1536.22	Wavelength 1536.22
•1536.61	Wavelength 1536.61
•1537	Wavelength 1537
•1537.40	Wavelength 1537.40
•1537.79	Wavelength 1537.79
•1538.19	Wavelength 1538.19
•1538.58	Wavelength 1538.58
•1538.98	Wavelength 1538.98
•1539.37	Wavelength 1539.37
•1539.77	Wavelength 1539.77
•1540.16	Wavelength 1540.16
•1540.56	Wavelength 1540.56
•1540.95	Wavelength 1540.95
•1541.35	Wavelength 1541.35
•1541.75	Wavelength 1541.75
•1542.14	Wavelength 1542.14
•1542.35	Wavelength 1542.35
•1542.54	Wavelength 1542.54
•1542.94	Wavelength 1542.94
•1543.33	Wavelength 1543.33
•1543.73	Wavelength 1543.73
•1544.13	Wavelength 1544.13
•1544.53	Wavelength 1544.53
•1544.92	Wavelength 1544.92
•1545.32	Wavelength 1545.32
•1545.72	Wavelength 1545.72
•1546.12	Wavelength 1546.12
•1546.52	Wavelength 1546.52
•1546.92	Wavelength 1546.92
•1547.32	Wavelength 1547.32
•1547.72	Wavelength 1547.72
•1548.12	Wavelength 1548.12
•1548.51	Wavelength 1548.51
•1548.92	Wavelength 1548.92
•1549.32	Wavelength 1549.32
•1549.71	Wavelength 1549.71
•1550	Wavelength 1500
•1550.12	Wavelength 1550.12
•1550.52	Wavelength 1550.52
•1550.92	Wavelength 1550.92
•1551.32	Wavelength 1551.32
•1551.72	Wavelength 1551.72
•1552.12	Wavelength 1552.12
•1552.52	Wavelength 1552.52
•1552.93	Wavelength 1552.93
•1553.33	Wavelength 1553.33
•1553.73	Wavelength 1553.73
•1554.13	Wavelength 1554.13
•1554.13	Wavelength 1554.13
•1554.94	Wavelength 1554.94
•1555.34	Wavelength 1555.34
•1555.75	Wavelength 1555.75
•1556.15	Wavelength 1556.15
•1556.55	Wavelength 1556.55
•1556.96	Wavelength 1556.96
•1557.36	Wavelength 1557.36
•1557.77	Wavelength 1557.77
•1558.17	Wavelength 1558.17
•1558.58	Wavelength 1558.58
•1558.98	Wavelength 1558.98
•1559.39	Wavelength 1559.39
•1559.79	Wavelength 1559.79
•1560.20	Wavelength 1560.20
•1560.61	Wavelength 1560.61
•1561.01	Wavelength 1561.01
•1561.42	Wavelength 1561.42
•1561.83	Wavelength 1561.83
•1570	Wavelength 1570
•1570.83	Wavelength 1570.83
•1571.24	Wavelength 1571.24
•1571.65	Wavelength 1571.65
•1572.06	Wavelength 1572.06
•1572.48	Wavelength 1572.48
•1572.89	Wavelength 1572.89
•1573.30	Wavelength 1573.30
•1573.71	Wavelength 1573.71
•1574.13	Wavelength 1574.13
•1574.54	Wavelength 1574.54
•1574.95	Wavelength 1574.95
•1575.37	Wavelength 1575.37
•1575.78	Wavelength 1575.78
•1576.20	Wavelength 1576.20
•1576.61	Wavelength 1576.61
•1577.03	Wavelength 1577.03
•1577.44	Wavelength 1577.44
•1577.86	Wavelength 1577.86
•1578.27	Wavelength 1578.27
•1578.69	Wavelength 1578.69
•1579.10	Wavelength 1579.10
•1579.52	Wavelength 1579.52
•1579.93	Wavelength 1579.93
•1580.35	Wavelength 1580.35
•1580.77	Wavelength 1580.77
•1581.18	Wavelength 1581.18
•1581.60	Wavelength 1581.60
•1582.02	Wavelength 1582.02
•1582.44	Wavelength 1582.44
•1582.85	Wavelength 1582.85
•1583.27	Wavelength 1583.27
•1583.69	Wavelength 1583.69
•1584.11	Wavelength 1584.11
•1584.53	Wavelength 1584.53
•1584.95	Wavelength 1584.95
•1585.36	Wavelength 1585.36
•1585.78	Wavelength 1585.78
•1586.20	Wavelength 1586.20
•1586.62	Wavelength 1586.62
•1587.04	Wavelength 1587.04
•1587.46	Wavelength 1587.46
•1587.88	Wavelength 1587.88
•1588.30	Wavelength 1588.30
•1588.73	Wavelength 1588.73
•1589.15	Wavelength 1589.15
•1589.57	Wavelength 1589.57
•1589.99	Wavelength 1589.99
•1590	Wavelength 1590
•1590.41	Wavelength 1590.41
•1590.83	Wavelength 1590.83
•1591.26	Wavelength 1591.26
•1591.68	Wavelength 1591.68
•1592.10	Wavelength 1592.10
•1592.52	Wavelength 1592.52
•1592.95	Wavelength 1592.95
•1593.37	Wavelength 1593.37
•1593.79	Wavelength 1593.79
•1594.22	Wavelength 1594.22
•1594.64	Wavelength 1594.64
•1595.06	Wavelength 1595.06
•1595.49	Wavelength 1595.49
•1596.34	Wavelength 1596.34
•1596.76	Wavelength 1596.76
•1597.19	Wavelength 1597.19
•1597.62	Wavelength 1597.62
•1598.04	Wavelength 1598.04
•1598.47	Wavelength 1598.47
•1598.89	Wavelength 1598.89
•1599.32	Wavelength 1599.32
•1599.75	Wavelength 1599.75
•1600.06	Wavelength 1600.06
•1601.03	Wavelength 1601.03
•1601.46	Wavelength 1601.46
•1601.88	Wavelength 1601.88
•1602.31	Wavelength 1602.31
•1602.74	Wavelength 1602.74
•1603.17	Wavelength 1603.17
•1603.60	Wavelength 1603.60
•1604.03	Wavelength 1604.03
•1610	Wavelength 1610
•USE-TWL1	Use Tunable Wavelength 1
<LOSSB>	the parameter type is REACH, which is the reach value.
•AUTOPROV	Autoprovisioning
•CX	Reach CX
•DX	Reach DX
•HX	Reach HX
•I1	Reach I1
•IR-1	Reach IR-1
•IR-2	Reach IR-2
•L1	Reach L1
•L2	Reach L2
•L3	Reach L3
•LR-1	Reach LR-1
•LR-2	Reach LR-2
•LR-3	Reach LR-3
•LX	Reach LX
•S1	Reach S1
•S2	Reach S2
•SR	Reach SR
•SR-1	Reach SR-1
•SX	Reach SX
•T	Reach T
•VX	Reach VX
•ZX	Reach ZX
<PST>	Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.
•IS	In service
•OOS	Out of service
<SST>	Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•AINS	Automatic in service
•DSBLD	Disabled
•LPBK	Loopback
•MEA	Mismatch of equipment and attributes
•MT	Maintenance mode
•OOG	Out of group
•SWDL	Software downloading
•UAS	Unassigned
•UEQ	Unequipped

11.5  ED-<MOD_PATH>

(Cisco ONS 15454, 15327, 15600, 15310) The Edit STS1, STS12C, STS18C, STS192C, STS24C, STS36C, STS3C, STS48C, STS96C, STS6C, STS9C, VC12, VC3, VT1, or VT2 (ED-<MOD_PATH>) command edits the attributes associated with synchronous transport signal (STS) and Virtual Tributary (VT) paths.

Usage Guidelines

The SFBER, SDBER, RVRTV, and RVTM parameters only apply topath protection configurations at the STS path level and ONS 15310_CL and ONS 15454 VT paths.

SFBER and SDBER also apply to the VT path level on the ONS 15310-CL and ONS 15454 when the ONS 15454 has an XC-VXC-10G card.

SWPDIP does not apply to the VT path level (VT1 and VT2).

The path trace message is a 64 character string including the terminating CR (carriage return) and LF (line feed) that is transported in the J1 byte of the SONET STS Path overhead. Both the EXPTRC and TRC string can be provisioned by user with up to 62 character string.

The EXPTRC indicates that the contents of the expected incoming path trace are provisioned by the user. The TRC indicates the contents of the outgoing path trace message. The INCTRC indicates the contents of the incoming path trace message.

Path trace has three modes: OFF, MANUAL, and AUTO. The path trace mode defaults to OFF. The MANUAL mode performs the comparison of the received string with the user-entered expected string. The AUTO mode performs the comparison of the present received string with an expected string that is set to a previously received string. If there is a mismatch, a TIM-P alarm is raised. When the path trace is in OFF mode, there is no path trace processing, and all of the alarm and state conditions are reset.

The TACC parameter edits an existing single STS or VT and changes it to a test access point. When an editing command on TACC is executed, it assigns the STS or VT for the first two-way connection and STS+1 as the second two-way connection. For single facility access digroup (FAD) test access, only a single STS/VT is used for the test access point (TAP) creation. For more information on TACC, refer to the Cisco ONS SDH and Cisco ONS 15600 SDH TL1 Reference Guide.

J1 is implemented on the DS1/DS1N, DS3E/DS3NE, DS3XM, EC1, OC3, OC12-4, OC48AS, and OC192 cards.

DS3/DS3N, OC12, OC48, E100, and E1000 cards do not support path trace.

DS1/DS1N, DS3E/DS3NE, and DS3XM support both TRC and EXPTRC in the ED-STS-PATH command.

EC1, OC3, OC48AS, and OC192 only support EXPTRC in the ED-STS-PATH command.

---

Note Each TL1 command must be less than or equal to 255 characters. Any command larger than 255 characters must be split into multiple commands. For example, if you use the ED-<MOD_PATH> command to edit the J1 EXPTRC/TRC message, path protection attributes, and TACC attributes and the command exceeds 255 characters, the command will not be processed. You must use multiple ED-<MOD_PATH> commands instead.

---

The following actions will produce error messages:

•Sending this command to edit SFBER, SDBER, RVRTV, or RVTM for the non-path protection STS path.

•Sending this command to edit the EXPTRC string with the AUTO path trace mode (TRCMODE=AUTO).

•Sending this command to edit TRC on any card other than DS3(N)E, DS1(N), and DS3XM cards, will return the "TRC-not allowed for monitor paths. Incorrect card type" error message.

•Sending this command to edit both TACC and any other attribute(s) will return the "Parameters Not compatible" error message.

•Sending this command to edit TACC on an AID with cross-connections will return the "STS in Use" error message.

---

Note•TACC creation will be denied on the protect ports/cards for 1:1, 1:N, and 1+1 protection.

•The VFAC AID is only valid on slots containing an ML-Series card. TACC is not supported for the ML-Series cards.

•After bidirectional line switched ring (BLSR) switching, provisioning of the J1 trace string or trace mode is not allowed on the protection path.

•TACC creation is allowed on protection channel access (PCA) for two-fiber and four-fiber BLSR.

•TACC is not supported on G1000, MXP_2.5G_10G, TXP_MR_10G, ML1000-2, and ML100T-12 cards.

•HOLDOFFTIMER is not specific to a path. It is applicable to the path protection selector. If HOLDOFFTIMER is changed on one path associated with the selector, the HOLDOFFTIMER of the other path associated with the same selector is also changed.

•The test set physical connection set up through ED-T3/DS1/STS1/VT1 of the DS3XM-12 card is only allowed on the physical front ports (PORTED ports, Ports 1 to 12), which are the monitoring ports.

–The monitoring test access ports follow the common rules for the other cards. For example, with an ED-T3 command on Port 2 (FAC-6-2) that has a TACC number (8), the next port, Port 3 (FAC-6-3) is used as the monitoring point also. The RTRV-T3 on both Port 2 and Port 3 return the same TACC number (8) used to monitor the cross-connection end (A-B). The last port (Port 12) is not allowed to set up a physical connection with the test set because there is no next available port to be the monitoring port.

–The TACC disconnection (DISC-TACC) and the test access mode change command (CHG-TACC) follow the same requirement as in the previous step, but it is applied on the ported ports of the DS3XM-12 card.

–The test access connection setup command (CONN-TACC) has monitored points, which can be portless ports. This command is applied on both ported and portless ports of the DS3XM-12 card.

•If the entity has a TACC connection, the entity is not allowed to have ported or portless STS/VT cross-connection (or circuit) provisioning on the DS3XM-12 card.

•Test access is not supported on the ONS 15310-CL.

•J2 path trace is not supported on the 15310-CL-CTX card of the ONS 15310-CL, however the CE-100T-8 or ML-100T-8 card provisioned in mapper mode does allow J2 provisioning.

•The cross-connects on the DS3i-N-12 card will be STS3c width, but the individual STS 1s within the 3C will be accessible. To edit the path attributes, use the ED-STS1 command with the FAC AID.

For TACC creation, use the ED-STS3C command because the TACC path width (like the cross-connect) has to be 3C on the DS3i-N-12 card. In this case, you are creating a new entity (TAP) on the DS3i-N-12 card that has to be of 3C width. On the DS3i-N-12 card, the ED0STS command can be used either with STS1 or STS3C depending on the parameter to be modified.

•For the selector path on a BLSR, the SWPDIP is not editable and is always in the ON state. If you attempt to edit SWPDIP (for the selector path on a BLSR), an error message will be returned.

•You can create an STS1 or VT1.5 single TAP on the DS3XM-12 card's last ported port (12) if the bandwidth is available on that port.

•Optical ports do not support MAN and AUTO trace mode because they are not capable of raising AIS on TIM-P. Use the AUTO-NO-AIS or MAN-NO-AIS trace mode on optical ports.

•Sending the ED-VT1/VT2 commands over ONS 15454 path protection paths to edit SFBER or SDBER (when the ONS 15454 does not have an XC-VXC-10G cross-connect) will return the "Invalid Operation For The XCON" error message.

•Sending the ED-VT1/VT2 commands to edit SDBER with 1E-9 will return the "Out Of Range" error message.

•On the ONS 15310-MA, J2 path trace is supported on DS1 ports only. J2 path trace is not supported on ONS 15310-MA OCn ports and EC1 ports.

---

Category

Paths

Security

Provisioning

Input Format

ED-<MOD_PATH>:[<TID>]:<AID>:<CTAG>:::[SFBER=<SFBER>],[SDBER=<SDBER>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[SWPDIP=<SWPDIP>],
[HOLDOFFTIMER=<HOLDOFFTIMER>],[EXPTRC=<EXPTRC>],[TRC=<TRC>],
[TRCMODE=<TRCMODE>],[TRCFORMAT=<TRCFORMAT>][TACC=<TACC>],
[TAPTYPE=<TAPTYPE>],[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];

Input Example

ED-STS3C:FERNDALE:STS-2-1-4:115:::SFBER=1E-3,SDBER=1E-5,RVRTV=Y,RVTM=1.0,
SWPDIP=Y,HOLDOFFTIMER=2000,EXPTRC="EXPTRCSTRING",TRC="TRCSTRING",
TRCMODE=OFF,TRCFORMAT=64-BYTE,TACC=8,TAPTYPE=SINGLE,
CMDMDE=CMDMDE:IS,AINS;

Input Parameters

<AID>	Access identifier from the "26.11  CrossConnectId1" section on page 26-25.
<SFBER>	Signal failure threshold. Applies only to path protection. Applies to STS-level paths in SONET (STSn) and to VT-level paths on the ONS 15310-CL with an XC-VXC-10G card. Defaults to 1E-4. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.
•1E-3	SFBER is 1E-3.
•1E-4	SFBER is 1E-4.
•1E-5	SFBER is 1E-5.
<SDBER>	Signal degrade threshold. Applies only to path protection. Applies to STS-level paths in SONET (STSn) and to VT-level paths on the ONS 15310-CL with an XC-VXC-10G card. 1E-9 is not allowed for VT-level/LO paths. Defaults to 1E-6. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.
•1E-5	SDBER is 1E-5.
•1E-6	SDBER is 1E-6.
•1E-7	SDBER is 1E-7.
•1E-8	SDBER is 1E-8.
•1E-9	SDBER is 1E-9.
<RVRTV>	Revertive mode. The value Y indicates that protection switching system reverts service to the original line after restoration. The value N indicates that protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. Only applies to path protection. The parameter type is ON_OFF, which disables or enables an attribute.
•N	Does not revert service to original line after restoration.
•Y	Reverts service to original line after restoration.
<RVTM>	Revertive time. RVTM is not allowed to be set while RVRTV is N. Only applies to path protection. The parameter type is REVERTIVE_TIME (revertive time).
•0.5 to 12.0	Revertive time is 0.5 to 12.0 minutes.
<SWPDIP>	On/off switch for path protection payload defect level switching. Applicable only to STS-level paths in SONET (STSn). For the selector path on a BLSR, SWPDIP is not editable and always ON. Defaults to N. The parameter type is ON_OFF, which disables or enables an attribute.
•N	Disable an attribute.
•Y	Enable an attribute.
<HOLDOFFTIMER>	Hold off timer for path protection dual-ring interconnect (DRI). Values must be within 0 and 10000 ms (0 to 10 seconds), with increments of 100 ms. Defaults to "existed value." HOLDOFFTIMER is an integer.
<EXPTRC>	Expected path trace content. Indicates the expected path trace message (J1) contents. EXPTRC is any 64-character ASCII string, including the terminating CR (carriage return) and LF (line feed). Applicable to STS-level paths in SONET (STSn). Applicable to VT-level paths for the DS3XM-12 and CE-100T-8 card on the ONS 15454 and the CE-100T-8 card on ONS 15310-CL. Defaults to 64 null characters. EXPTRC is a string.
<TRC>	The path trace message to be transmitted. The trace byte (J1) continuously transmits a 64-byte, fixed length ASCII string, one byte at a time. A null value defaults to the network element (NE) transmitting 62 null characters (hex 00) and CR and LF. Applicable to STS-level paths in SONET (STSn). Applicable to VT-level paths for the DS3XM-12 and CE-100T-8 card on the ONS 15454 and the CE-100T-8 card on ONS 15310-CL. For ONS 15310-CL, TRC is not provisionable on the EC/OC ports. Defaults to 64 null characters. TRC is a string.
<TRCMODE>	Path trace mode. Applicable only to STS-level paths in SONET (STSn). Defaults to the OFF mode. ONS 15310-CL EC/OC ports do not support MAN and AUTO, but can be configured as MAN-NO-AIS and AUTO-NO-AIS. Note The ONS 15600 does not support MAN and AUTO The parameter type is TRCMODE (trace mode).
•AUTO	Use the previously received path trace string as the expected string. Not applicable to muxponder (MXP) and transponder (TXP) cards.
•AUTO-NO-AIS	Use the previously received path trace string as the expected string and do not turn on the alarm indication signal (AIS) and remote defect indication (RDI) if TIM-P is detected.
•MAN	Use the provisioned expected string as the expected string.
•MAN-NO-AIS	Use the provisioned expected string as the expected string and do not turn on AIS and RDI if TIM-P is detected.
•OFF	Turn off path trace capability. Nothing will be reported.
<TRCFORMAT>	Path trace format. Only 64-byte is supported. Defaults to 64-byte. The parameter type is TRCFORMAT (trace format).
•64-BYTE	64 byte trace message
<TACC>	TAP number within a range of 0 to 999. Indicates whether the digroup being provisioned is to be used as a test access digroup. When TACC is 0 (zero), the TAP is deleted. TACC is an integer.
<TAPTYPE>	TAP type. Defaults to DUA The parameter type is TAPTYPE, which is the test access point type.
•DUAL	Dual FAD
•SINGLE	Single FAD
<CMDMDE>	The parameter type is command mode (CMDMDE). Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in IS-NR or OOS-AU,AINS service states.
•FRCD	Force the system to override a state where the command would normally be denied.
•NORM	Execute the command normally. Do not override any conditions that might make the command fail.
<PST>	Primary state. Defaults to IS. The parameter type is PST, which indicates the current overall service condition of an entity.
•IS	In service
•OOS	Out of service
<SST>	Secondary state. Defaults to AINS. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•AINS	Automatic in service
•DSBLD	Disabled
•LPBK	Loopback
•MEA	Mismatch of equipment and attributes
•MT	Maintenance mode
•OOG	Out of group
•SWDL	Software downloading
•UAS	Unassigned
•UEQ	Unequipped

11.6  ED-<MOD_RING>

(Cisco ONS 15454 and ONS 15600) The Edit Bidirectional Line Switched Ring (ED-<MOD_RING>) command edits the BLSR attributes.

Usage Guidelines

ONS 15600 does not support four-fiber BLSR.

The RVRTV, RVTM, SRVRTV, SRVTM, NODEID, and RINGID attributes can be edited for the four-fiber BLSR.

The RVRTV, RVTM, NODEID, and RINGID attributes can be edited for the two-fiber BLSR.

The following actions will produce errors:

•If the system fails on getting IOR, a SROF (Get IOR Failed) error message is returned.

•If the AID is invalid, an IIAC (Invalid AID) error message is returned.

•If the BLSR does not exist, a SRQN (BLSR Does Not Exist) error message is returned.

•The SROF (Facility Not Provisioned) or (Cannot Access BLSR) error message will be returned for an invalid query.

•The SRQN (BLSR Edition Failed) error message is returned for an invalid edition query.

•Sending this command to modify SRVRTV or SRVTM on a two-fiber BLSR will return an IDNV (Invalid Data For 2F-BLSR) error message.

•Sending this command to modify the nodeid with invalid data will return an IIAC (Invalid NodeId) error message.

•Sending this command to change the ringid into invalid data will return an IIAC (Invalid RingId) error message.

•Changing the BLSR nodeid with a duplicated ID will return a SROF (Cannot Set NodeId) error message.

•Changing the BLSR ringid with a duplicated ID will return a SROF (Cannot Set RingId) error message is returned.

---

Note•The ALL AID is invalid for this command.

•The list AID format is supported for Software Release 4.6 and later.

Category

BLSR

Security

Provisioning

Input Format

ED-<MOD_RING>:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>],[NODEID=<NODEID>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[SRVRTV=<SRVRTV>],[SRVTM=<SRVTM>][:];

Input Example

ED-BLSR:PETALUMA:BLSR-43:123:::RINGID=43,NODEID=3,RVRTV=Y,RVTM=2.0,
SRVRTV=Y,SRVTM=5.0;

Input Parameters

<AID>	Access identifier from the "26.3  AidUnionId1" section on page 26-16. Identifies the BLSR of the NE. The ALL and BLSR-ALL AIDs are not allowed for editing BLSRs.
<RINGID>	The BLSR ID of the NE up to six characters. Valid characters are A-Z and 0-9. RINGID is a string.
<NODEID>	The BLSR node ID of the NE. NODEID ranges from 0 to 31. It is an integer.
<RVRTV>	Revertive mode. The value Y indicates that protection switching system reverts service to the original line after restoration. The value N indicates that protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. The parameter type is ON_OFF, which disables or enables an attribute.
•N	Does not revert service to original line after restoration.
•Y	Reverts service to original line after restoration.
<RVTM>	Revertive time. RVTM is not allowed to be set while RVRTV is N. The parameter type is REVERTIVE_TIME (revertive time).
•0.5 to 12.0	Revertive time is 0.5 to 12.0 minutes.
<SRVRTV>	The span revertive mode for four-fiber BLSR only. The parameter type is ON_OFF, which disables or enables an attribute.
•N	Disable an attribute.
•Y	Enable an attribute.
<SRVTM>	The span revertive time for four-fiber BLSR only. SRVTM is not allowed to be set while SRVRTV is N. The parameter type is REVERTIVE_TIME (revertive time).
•0.5 to 12.0	Revertive time is 0.5 to 12.0 minutes.

11.7  ED-<OCN_TYPE>

(Cisco ONS 15454, 15327, 15600, 15310) The Edit OC3, OC12, OC48, or OC192 (ED-<OCN_TYPE>) command edits the attributes (for example, service parameters) and status of an OC-N facility. Allowable states for a facility are Out Of Service (OOS), Out Of Service and Automatic In Service (OOS-AINS), Out Of Service and Maintenance (OOS-MT), and In Service (IS). See Table 28-1 on page 28-1 for supported modifiers by platform.

Usage Guidelines

•The data communications channel (DCC) transmit side is bridged to both working and protect in a 1+1 protection scheme. On the receive side, the active one is selected for DCC. The DCC is provisioned on the working port only in a 1+1 protection scheme.

•All lines in a 1+1 BLSR must have the same mode. If you change the mode of a line that is in a 1+1 BLSR, an error message will be returned.

•You cannot directly transition a facility from IS to OOS-MA,DSBLD service state. You can transition a facility to OOS-MA,DSBLD service state from any state except OOS-MA,MT. To transition a facility from OOS-MA,MT to OOS-MA,DSBLD service state, all the following conditions must be met:

–The facility is not sourcing a synchronization clock

–The facility's DCC is disabled

–The facility is not part of a protection group

–The facility is not supporting cross-connects

–The facility is not using overhead connections or overhead terminations (such as express orderwire, local orderwire, or user data channels [UDCs])

---

Note The conditions stipulated can be overridden by using the CMDMDE=FRCD option. The FRCD option will immediately remove the facility from service (except for IS to OOS-MA,DSBLD transition) with no consideration for orderly interruption.

---

---

Note OSI parameters are not supported in Release 9.0.

---

Category

Ports

Security

Provisioning

Input Format

ED-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>:::[DCC=<DCC>],[AREA=<AREA>],[SYNCMSG=<SYNCMSG>],[SENDDUS=<SENDDUS>],[PJMON=<PJMON>],[SFBER=<SFBER>],[SDBER=<SDBER>],[MODE=<MODE>],[SOAK=<SOAK>],[OSPF=<OSPF>],[LDCC=<LDCC>],[NAME=<NAME>],[CMDMDE=<CMDMDE>],[EXPTRC=<EXPTRC>],[TRC=<TRC>],[TRCMODE=<TRCMODE>],[TRCFORMAT=<TRCFORMAT>],[ADMSSM=<ADMSSM>],[SENDDUSFF=<SENDDUSFF>],[AISONLPBK=<AISONLPBK>],[FOREIGNFEND=<FOREIGNFAREND>],[FOREIGNIP=<FOREIGNIPADDRESS>],[FREQ=<FREQ>],[LOSSB=<LOSSB>],[OPRNOMINAL=<OPRNOMINAL>],[OSISDCC=<OSISDCC>],[OSILDCC=<OSILDCC>],[OSIROUTER=<OSIROUTER>],[:<PST>[,<SST>]];

Input Example

ED-OC48:PENNGROVE:FAC-6-1:114:::DCC=Y,AREA=10.92.63.1,SYNCMSG=N,
SENDDUS=N,PJMON=48,SFBER=1E-4,SDBER=1E-6,MODE=SINGLESHELF,MUX=E2,
SOAK=10,OSPF=Y,LDCC=N,NAME="OCNPORT",CMDMDE=CMDMDE,EXPTRC="AAA",
TRC="AAA",TRCMODE=MAN,TRCFORMAT=16-BYTE,ADMSSM=PRS,SENDDUSFF=N,
AISONLPBK=AIS_ON_LPBK_ALL,FREQ=1550,LOSSB=LR-1,FOREIGNFEND=N,
FOREIGNIP="IP ADDRESS",OSISDCC=Y,OSILDCC=Y,OSIROUTER=1:IS,AINS;

Input Parameters

<AID>	Access identifier from the "26.15  FACILITY" section on page 26-34.
<DCC>	Indicates whether or not the SDCC is to be used. Identifies the SDCC connection of the port. The parameter type is ON_OFF, which disables or enables an attribute.
•N	Disable an attribute.
•Y	Enable an attribute.
<AREA>	The area ID and shows up only if the DCC is enabled. AREA is a string.
<SYNCMSG>	Synchronization status message. The parameter type is EXT_RING, which indicates whether the ring supports the extended K1/K2/K3 protocol.
•N	The ring does not support the extended K1/K2/K3 protocol.
•Y	The ring does support the extended K1/K2/K3 protocol.
<SENDDUS>	The facility will send the DUS (Do not use for Synchronization) value as the SSM for that facility. The parameter type is ON_OFF, which disables or enables an attribute.
•N	Disable an attribute.
•Y	Enable an attribute.
<PJMON>	Identifies an OC-N port PJMON. PJMON is an integer. It defaults to 0 (zero). Set a valid STS number of the optical port. Note The PJMON number displayed in TL1 interface does not correspond to the PJVC4MON number in CTC, but instead corresponds to the STS number of the optical port.
<SFBER>	Signal failure threshold. The parameter type is SF_BER, which is the threshold for declaring signal failure on a facility or path.
•1E-3	SFBER is 1E-3.
•1E-4	SFBER is 1E-4.
•1E-5	SFBER is 1E-5.
<SDBER>	Signal degrade threshold. The parameter type is SD_BER, which is the threshold for declaring signal degrade on a facility or path.
•1E-5	SDBER is 1E-5.
•1E-6	SDBER is 1E-6.
•1E-7	SDBER is 1E-7.
•1E-8	SDBER is 1E-8.
•1E-9	SDBER is 1E-9.
<MODE>	OC-N port mode. the parameter type is OPTICAL_MODE, which is the facility's optical mode.
•SINGLESHELF	The NE contains only one shelf and the AID representation does not consider the shelf identifier for command requests/response and autonomous reports.
•MULTISHELF	The AID representation considers the shelf identifier for command requests/response and autonomous reports. This means the NE has more than one shelf configured or the user wants to use the new AID style.
•MULTISHELFETH	The AID representation considers the shelf identifier for command requests/response and autonomous reports. This means the NE has more than one shelf configured or the user wants to use the new AID style. The shelves are connected by means of an external Ethernet switch.
<MUX>	BLSR extension byte (supported only on the OC48AS card). MUX cannot be configured if: •The card is SONET and the media type is SDHT. •The card has an orderwire or user data channel (UDC) connection. •This is a protect line and the working line has an orderwire or UDC connection. The parameter type is MUX_TYPE, which is the BLSR extension type.
•E2	E2 byte (orderwire)
•F1	F1 byte (user)
•K3	K3 byte
•Z2	Z2 byte
<SOAK>	OOS-AINS to IS transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). Defaults to 32. SOAK is an integer.
<OSFP>	The Open Shortest Path First discovery. Defaults to Y. The parameter type is ON_OFF, which disables or enables an attribute.
•N	Disable an attribute.
•Y	Enable an attribute.
<LDCC>	The LDCC connection on the port. Defaults to N. the parameter type is EXT_RING, which indicates if the ring supports the extended K1/K2/K3 protocol.
•N	The ring does not support the extended K1/K2/K3 protocol.
•Y	The ring does support the extended K1/K2/K3 protocol.
<NAME>	NAME is a user-specified string to identify the facility. It defaults to NULL. Its maximum length is 32 characters.
<CMDMDE>	The parameter type is command mode (CMDMDE). Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in IS-NR or OOS-AU,AINS service states.
•FRCD	Force the system to override a state where the command would normally be denied.
•NORM	Execute the command normally. Do not override any conditions that might make the command fail.
<EXPTRC>	Expected path trace content. Indicates the expected path trace message (J1) contents. EXPTRC is any 64-character ASCII string, including the terminating CR (carriage return) and LF (line feed). Applicable to STS-level paths in SONET (STSn). Applicable to VT-level paths for the DS3XM-12 card on the ONS 15454. Defaults to NULL. EXPTRC is a string.
<TRC>	The path trace message to be transmitted. The trace byte (J1) continuously transmits a 64-byte, fixed length ASCII string, one byte at a time. A null value defaults to the NE transmitting 62 null characters (hex 00) and CR and LF. Applicable to STS-level paths in SONET (STSn). Applicable to VT-level paths for the DS3XM-12 card on the ONS 15454. TRC is a string.
<TRCMODE>	Path trace mode. Applicable only to STS-level paths in SONET (STSn). Defaults to MAN. The parameter type is TRCMODE (trace mode).
•AUTO	Use the previously received path trace string as the expected string. Not applicable to MXP or TXP cards.
•AUTO-NO-AIS	Use the previously received path trace string as the expected string and do not turn on AIS and RDI if TIMP is detected.
•MAN	Use the provisioned expected string as the expected string.
•MAN-NO-AIS	Use the provisioned expected string as the expected string and do not turn on AIS and RDI if TIMP is detected.
•OFF	Turn off path trace capability. Nothing will be reported.
<TRCFORMAT>	Trace message size. The parameter type is TRCFORMAT (trace format).
•1-BYTE	1 byte trace message
•16-BYTE	16 byte trace message
•64-BYTE	64 byte trace message
<ADMSSM>	SSM selectable value. It will only appear when SSM is disabled. Defaults to STU. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SONET.
•DUS	Do Not Use For Synchronization
•PRS	Primary Reference Source, Stratum 1 Traceable
•RES	Reserved For Network Synchronization Use
•SMC	SONET Minimum Clock Traceable
•ST2	Stratum 2 Traceable
•ST3	Stratum 3 Traceable
•ST3E	Stratum 3E Traceable
•ST4	Stratum 4 Traceable
•STU	Synchronized, Traceability Unknown
•TNC	Transit Node Clock (2nd Generation Only)
<SENDDUSFF>	The parameter type is ON_OFF, which disables or enables an attribute.
•N	Disable an attribute.
•Y	Enable an attribute.
<AISONLPBK>	The parameter type is AIS_ON_LPBK, which indicates if AIS is sent on a loopback.
•FACILITY	AIS is sent on facility loopbacks.
•ALL	AIS is sent on all loopbacks.
•OFF	AIS is not sent on loopbacks.
•TERMINAL	AIS is sent on terminal loopbacks.
<FREQ>	The parameter type is OPTICAL_WLEN (optical wavelength).
•1310	Wavelength 1310
•1470	Wavelength 1470
•1490	Wavelength 1490
•1510	Wavelength 1510
•1529.55	Wavelength 1529.55
•1529.94	Wavelength 1529.94
•1530	Wavelength 1530
•1530.33	Wavelength 1530.33
•1530.73	Wavelength 1530.73
•1531.12	Wavelength 1531.12
•1531.51	Wavelength 1531.51
•1531.90	Wavelength 1531.90
•1532.29	Wavelength 1532.29
•1532.68	Wavelength 1532.68
•1533.07	Wavelength 1533.07
•1533.47	Wavelength 1533.47
•1533.86	Wavelength 1533.86
•1534.25	Wavelength 1534.25
•1534.64	Wavelength 1534.64
•1535.04	Wavelength 1535.04
•1535.43	Wavelength 1535.43
•1535.82	Wavelength 1535.82
•1536.22	Wavelength 1536.22
•1536.61	Wavelength 1536.61
•1537	Wavelength 1537
•1537.40	Wavelength 1537.40
•1537.79	Wavelength 1537.79
•1538.19	Wavelength 1538.19
•1538.58	Wavelength 1538.58
•1538.98	Wavelength 1538.98
•1539.37	Wavelength 1539.37
•1539.77	Wavelength 1539.77
•1540.16	Wavelength 1540.16
•1540.56	Wavelength 1540.56
•1540.95	Wavelength 1540.95
•1541.35	Wavelength 1541.35
•1541.75	Wavelength 1541.75
•1542.14	Wavelength 1542.14
•1542.35	Wavelength 1542.35
•1542.54	Wavelength 1542.54
•1542.94	Wavelength 1542.94
•1543.33	Wavelength 1543.33
•1543.73	Wavelength 1543.73
•1544.13	Wavelength 1544.13
•1544.53	Wavelength 1544.53
•1544.92	Wavelength 1544.92
•1545.32	Wavelength 1545.32
•1545.72	Wavelength 1545.72
•1546.12	Wavelength 1546.12
•1546.52	Wavelength 1546.52
•1546.92	Wavelength 1546.92
•1547.32	Wavelength 1547.32
•1547.72	Wavelength 1547.72
•1548.12	Wavelength 1548.12
•1548.51	Wavelength 1548.51
•1548.92	Wavelength 1548.92
•1549.32	Wavelength 1549.32
•1549.71	Wavelength 1549.71
•1550	Wavelength 1500
•1550.12	Wavelength 1550.12
•1550.52	Wavelength 1550.52
•1550.92	Wavelength 1550.92
•1551.32	Wavelength 1551.32
•1551.72	Wavelength 1551.72
•1552.12	Wavelength 1552.12
•1552.52	Wavelength 1552.52
•1552.93	Wavelength 1552.93
•1553.33	Wavelength 1553.33
•1553.73	Wavelength 1553.73
•1554.13	Wavelength 1554.13
•1554.13	Wavelength 1554.13
•1554.94	Wavelength 1554.94
•1555.34	Wavelength 1555.34
•1555.75	Wavelength 1555.75
•1556.15	Wavelength 1556.15
•1556.55	Wavelength 1556.55
•1556.96	Wavelength 1556.96
•1557.36	Wavelength 1557.36
•1557.77	Wavelength 1557.77
•1558.17	Wavelength 1558.17
•1558.58	Wavelength 1558.58
•1558.98	Wavelength 1558.98
•1559.39	Wavelength 1559.39
•1559.79	Wavelength 1559.79
•1560.20	Wavelength 1560.20
•1560.61	Wavelength 1560.61
•1561.01	Wavelength 1561.01
•1561.42	Wavelength 1561.42
•1561.83	Wavelength 1561.83
•1570	Wavelength 1570
•1570.83	Wavelength 1570.83
•1571.24	Wavelength 1571.24
•1571.65	Wavelength 1571.65
•1572.06	Wavelength 1572.06
•1572.48	Wavelength 1572.48
•1572.89	Wavelength 1572.89
•1573.30	Wavelength 1573.30
•1573.71	Wavelength 1573.71
•1574.13	Wavelength 1574.13
•1574.54	Wavelength 1574.54
•1574.95	Wavelength 1574.95
•1575.37	Wavelength 1575.37
•1575.78	Wavelength 1575.78
•1576.20	Wavelength 1576.20
•1576.61	Wavelength 1576.61
•1577.03	Wavelength 1577.03
•1577.44	Wavelength 1577.44
•1577.86	Wavelength 1577.86
•1578.27	Wavelength 1578.27
•1578.69	Wavelength 1578.69
•1579.10	Wavelength 1579.10
•1579.52	Wavelength 1579.52
•1579.93	Wavelength 1579.93
•1580.35	Wavelength 1580.35
•1580.77	Wavelength 1580.77
•1581.18	Wavelength 1581.18
•1581.60	Wavelength 1581.60
•1582.02	Wavelength 1582.02
•1582.44	Wavelength 1582.44
•1582.85	Wavelength 1582.85
•1583.27	Wavelength 1583.27
•1583.69	Wavelength 1583.69
•1584.11	Wavelength 1584.11
•1584.53	Wavelength 1584.53
•1584.95	Wavelength 1584.95
•1585.36	Wavelength 1585.36
•1585.78	Wavelength 1585.78
•1586.20	Wavelength 1586.20
•1586.62	Wavelength 1586.62
•1587.04	Wavelength 1587.04
•1587.46	Wavelength 1587.46
•1587.88	Wavelength 1587.88
•1588.30	Wavelength 1588.30
•1588.73	Wavelength 1588.73
•1589.15	Wavelength 1589.15
•1589.57	Wavelength 1589.57
•1589.99	Wavelength 1589.99
•1590	Wavelength 1590
•1590.41	Wavelength 1590.41
•1590.83	Wavelength 1590.83
•1591.26	Wavelength 1591.26
•1591.68	Wavelength 1591.68
•1592.10	Wavelength 1592.10
•1592.52	Wavelength 1592.52
•1592.95	Wavelength 1592.95
•1593.37	Wavelength 1593.37
•1593.79	Wavelength 1593.79
•1594.22	Wavelength 1594.22
•1594.64	Wavelength 1594.64
•1595.06	Wavelength 1595.06
•1595.49	Wavelength 1595.49
•1596.34	Wavelength 1596.34
•1596.76	Wavelength 1596.76
•1597.19	Wavelength 1597.19
•1597.62	Wavelength 1597.62
•1598.04	Wavelength 1598.04
•1598.47	Wavelength 1598.47
•1598.89	Wavelength 1598.89
•1599.32	Wavelength 1599.32
•1599.75	Wavelength 1599.75
•1600.06	Wavelength 1600.06
•1601.03	Wavelength 1601.03
•1601.46	Wavelength 1601.46
•1601.88	Wavelength 1601.88
•1602.31	Wavelength 1602.31
•1602.74	Wavelength 1602.74
•1603.17	Wavelength 1603.17
•1603.60	Wavelength 1603.60
•1604.03	Wavelength 1604.03
•1610	Wavelength 1610
•USE-TWL1	Use Tunable Wavelength 1
<LOSSB>	The parameter type is REACH (reach value)
•AUTOPROV	Autoprovisioning
•CX	Reach CX
•DX	Reach DX
•HX	Reach HX
•I1	Reach I1
•IR-1	Reach IR-1
•IR-2	Reach IR-2
•L1	Reach L1
•L2	Reach L2
•L3	Reach L3
•LR-1	Reach LR-1
•LR-2	Reach LR-2
•LR-3	Reach LR-3
•LX	Reach LX
•S1	Reach S1
•S2	Reach S2
•SR	Reach SR
•SR-1	Reach SR-1
•SX	Reach SX
•T	Reach T
•VX	Reach VX
•ZX	Reach ZX
<FOREIGNFEND>	Indicates whether the far-end NE on the DCC is a foreign NE. The parameter type is ON_OFF, which disables or enables an attribute.
•N	Disable an attribute.
•Y	Enable an attribute.
<FOREIGNIP>	The IP address of the far-end NE on the DCC. Used only if FOREIGNFEND is Y. FOREIGHNIP is a string.
<OPRNOMINAL>	Set to Y reads the current raw optical receive power and sets the raw OPR value as nomimal optical receive power. After executing this command, the OPRN is set to approximately 100. Note The OPRNOMINAL value of N is not supported. The parameter type is ON_OFF, which disables or enables an attribute.
•N	Disable an attribute. Not supported for OPRNOMINAL.
•Y	Enable an attribute.
OSISDCC	Indicates whether or not the OSI SDCC is to be used. Identifies the SDCC connection of the port. The parameter type is ON_OFF, which disables or enables an attribute.
•Y	Enable an attribute.
•N	Disable an attribute.
OSILDCC	Indicates whether or not the OSI LDCC is to be used. Identifies the SDCC connection of the port. The parameter type is ON_OFF, which disables or enables an attribute.
•Y	Enable an attribute.
•N	Disable an attribute.
OSIROUTER	The OSI virtual router number in the range of 1 to 3 for 15454 SDH.
<PST>	Primary state. Defaults to IS. The parameter type is PST, which indicates the current overall service condition of an entity.
•IS	In service
•OOS	Out of service
<SST>	Secondary state. Defaults to AINS. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•AINS	Automatic in service
•DSBLD	Disabled
•LPBK	Loopback
•MEA	Mismatch of equipment and attributes
•MT	Maintenance mode
•OOG	Out of group
•SWDL	Software downloading
•UAS	Unassigned
•UEQ	Unequipped

11.8  ED-ALS

(Cisco ONS 15454, ONS 15310-CL, ONS 15310-MA, ONS 15600) The Edit Automatic Laser Shutdown (ED-ALS) command is used to modify the ALS attributes of an OC-N facility and all the facilities that support the ALS feature. For transponder and muxponder cards, this command is used to modify the ALS parameter of the OC48 and OC192 ports.

Usage Guidelines

None

Category

Ports

Security

Provisioning

Input Format

ED-ALS:[<TID>]:<SRC>:<CTAG>:::[ALSMODE=<ALSMODE>],[ALSRCINT=<ALSRCINT>],
[ALSRCPW=<ALSRCPW>][:];

Input Example

ED-ALS::CHAN-1-1-1:100:::ALSMODE=AUTO,ALSRCINT=130,ALSRCPW=80.1;

Input Parameters

<SRC>	Access identifier from the "26.2  AidUnionId" section on page 26-12.
<ALSMODE>	ALS is enabled or disabled. The parameter type is ALS_MODE, which is the working mode for automatic laser shutdown.
•AUTO	Automatic
•DISABLED	Disabled
•MAN	Manual
•MAN-RESTART	Manual restart for test
<ALSRCINT>	ALS recovery interval. The range is 60 to 300 seconds. ALSRCINT is an integer.
<ALSRCPW>	ALS recovery pulse width. The range is 2.0 to 100.00 seconds, in increments of 100 ms. ALSRCWP is a float.

11.9  ED-APC

(Cisco ONS 15454) The Edit Amplification Power Control (ED-APC) command is used to modify the APC application attributes. The default value for an optional parameter is the NE default value. The value might not be the current value for the parameter. Use a retrieve command to retrieve the current value.

Usage Guidelines

None

Category

DWDM

Security

Provisioning

Input Format

ED-APC[:<TID>]:<AID>:<CTAG>[::<ROLE>][:APCENABLE=<APCENABLE>][:];

Input Example

ED-APC:PENNGROVE:WDMSIDE-A:CTAG:::APCENABLE=N;

Input Parameters

<WDMSIDE>	The AID is used to access the WDM side of an MSTP node.
•WDMSIDE-{UNKNOWN,A,B,C,D,E,F,G,H}	MSTP side identifier
<ROLE>	The role the unit is playing in the protection group.
•PROT	The entity is the protection unit in the protection group.
•WORK	The entity is the working unit in the protection group.
<APCENABLE>	Enable or disable the APC application. Default is N. The parameter type is ON_OFF, which disables or enables an attribute.
•N	Disable an attribute.
•Y	Enable an attribute.

11.10  ED-BITS

(Cisco ONS 15454, 15327, 15600, 15310) The Edit Building Integrated Timing Supply (ED-BITS) command edits the building integrated timing supply (BITS) reference attributes.

Usage Guidelines

The SYNC-BITS1 and SYNC-BITS2 AIDs can be used to set the BITS-OUT port state. For a BITS facility, 64 k and 6 MHz are only applicable to ON. SSM selectable (ADMSSM) is not applicable to ONS 15600. The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. Use a retrieve command to obtain the current value.

Category

Synchronization

Security

Provisioning

Input Format

ED-BITS:[<TID>]:<AID>:<CTAG>:::[LINECDE=<LINECDE>],[FMT=<FMT>],[LBO=<LBO>],
[SYNCMSG=<SYNCMSG>],[AISTHRSHLD=<AISTHRSHLD>],[SABIT=<SABIT>],
[BITSFAC=<BITSFAC>],[ADMSSM=<ADMSSM>][:<PST>];

Input Example

ED-BITS:SONOMA:BITS-2:779:::LINECDE=AMI,FMT=ESF,LBO=0-133,SYNCMSG=N,
AISTHRSHLD=PRS,SABIT=BYTE-5,IMPEDANCE=120-OHM,BITSFAC=T1,ADMSSM=PRS:IS;

Input Parameters

<AID>	Access identifier from the "26.6  BITS" section on page 26-18.
<LINECDE>	The parameter type is LINE_CODE (line code).
•AMI	Line code value is AMI.
•B8ZS	Line code value is B8ZS (binary 8-zero substitution).
<FMT>	Digital signal frame format. The parameter type is FRAME_FORMAT, which is the frame format for a T1 port.
•D4	Frame format is D4.
•ESF	Frame format is Extended Superframe (ESF).
•UNFRAMED	Frame format is unframed.
<LBO>	Line build-out settings. BITS line build-out. Default value is 0 to 133. LBO is an integer. The parameter type is BITS_LineBuildOut (BITS line build-out).
•0-133	BITS line build-out range is 0-133.
•134-266	BITS line build-out range is 134-266.
•267-399	BITS line build-out range is 267-399.
•400-533	BITS line build-out range is 400-533.
•534-655	BITS line build-out range is 534-655.
<SYNCMSG>	Indicates if the BITS facility supports synchronization status message. Default is ON (Y). The parameter type is EXT_RING, which indicates whether the ring supports the extended K1/K2/K3 protocol.
•N	The ring does not support the extended K1/K2/K3 protocol.
•Y	The ring does support the extended K1/K2/K3 protocol.
<AISTHRSHLD>	Alarm indication signal threshold. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SONET.
•DUS	Do Not Use For Synchronization
•PRS	Primary Reference Source, Stratum 1 Traceable
•RES	Reserved For Network Synchronization Use
•SMC	SONET Minimum Clock Traceable
•ST2	Stratum 2 Traceable
•ST3	Stratum 3 Traceable
•ST3E	Stratum 3E Traceable
•ST4	Stratum 4 Traceable
•STU	Synchronized, Traceability Unknown
•TNC	Transit Node Clock (2nd Generation Only)
<SABIT>	When the frame format selection is E1, SABIT is the bit used to receive and transmit the SSM. The parameter type is SABITS (SA BITS).
•BYTE-4	SABIT is BYTE-4.
•BYTE-5	SABIT is BYTE-5.
•BYTE-6	SABIT is BYTE-6.
•BYTE-7	SABIT is BYTE-7.
•BYTE-8	SABIT is BYTE-8.
<IMPEDANCE>	When the frame format selection is E1, IMPEDANCE is the terminal impedance of the BITS-IN port. The parameter type is IMPEDANCE, which is the terminal impedance of the BITS-IN port.
•120-OHM	Impedance of 120 ohm
•75-OHM	Impedance of 75 ohm
<BITSFAC>	BITS facility settings. BITS-2 always inherits the value of BITS-1. The parameter type is BITS_FAC (the BITS facility rate). 64 k and 6 MHz are only applicable to the ONS 15454.
•2 M	2 MHz rate
•64 K	64 K rate
•6 M	6 MHz rate
•E1	E1 rate
•T1	T1 rate
<ADMSSM>	SSM selectable. Only applicable to BITS-IN when SSM is disabled. Note Not applicable for ONS 15600. The parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL, which is the clock source quality level for SONET.
•DUS	Do Not Use For Synchronization
•PRS	Primary Reference Source, Stratum 1 Traceable
•RES	Reserved For Network Synchronization Use
•SMC	SONET Minimum Clock Traceable
•ST2	Stratum 2 Traceable
•ST3	Stratum 3 Traceable
•ST3E	Stratum 3E Traceable
•ST4	Stratum 4 Traceable
•STU	Synchronized, Traceability Unknown
•TNC	Transit Node Clock (2nd Generation Only)
<PST>	The primary state. The parameter type is PST, which indicates the current overall service condition of an entity.
•IS	In service
•OOS	Out of service

11.11  ED-BULKROLL-<OCN_TYPE>

(Cisco ONS 15454, 15327, 15600, 15310) The Edit Bulkroll for OC12, OC192, OC3, or OC48 (ED-BULROLL-<OCN_TYPE>) command edits information about the rolling of traffic from one endpoint to another without interrupting service. This command uses the FORCE option to force a valid signal. The only parameters that can be edited are RMODE and FORCE. The time slots cannot be edited. Use ED-ROLL-<MOD_PATH> for single path level rolling.

Usage Guidelines

See Table 28-1 on page 28-1 for supported modifiers by platform.

Category

Bridge and Roll

Security

Provisioning

Input Format

ED-BULKROLL-<OCN_TYPE>:[<TID>]:<FROM>:<CTAG>:::
[RFROMSTART=<RFROMSTART>],[RFROMEND=<RFROMEND>],[CMDMDE=<CMDMDE>];

Input Example

ED-BULKROLL-OC48:PETALUMA:FAC-1-1:1:::RFROMSTART=STS-1-1-1,
RFROMEND=STS-1-1-11,CMDMDE=FRCD;

Input Parameters

<FROM>	One of the endpoints. Access identifier from the "26.15  FACILITY" section on page 26-34 for line level rolling and bulk rolling.
<RFROMSTART>	The starting time slot in the source roll port. For bulk rolling only. The AID is from the "26.11  CrossConnectId1" section on page 26-25 (except VCM and FACILITY). Defaults to STS-<FROMSLOT>-<FROMPORT>-1, where <FROMSLOT> and <FROMPORT> are the slot and port of the <FROM> AID.
<RFROMEND>	The ending time slot in the source roll port. For bulk rolling only. The AID is from the "26.11  CrossConnectId1" section on page 26-25 (except VCM and FACILITY). Defaults to STS-<FROMSLOT>-<FROMPORT>-N, where <FROMSLOT> and <FROMPORT> are the slot and port of the <FROM> AID and N is the value of OCn. (for example, OC48, n=48).
<CMDMDE>	The parameter type is command mode (CMDMDE). Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in IS-NR or OOS-AU,AINS service states.
•FRCD	Force the system to override a state where the command would normally be denied.
•NORM	Execute the command normally. Do not override any conditions that might make the command fail.

11.12  ED-BWP-ETH

(Cisco ONS 15454) This command is used to modify a Bandwidth Profile entry in BWP DB. The BWP DB is a collection of BWP used in a Network Element.

Usage Guidelines

Error conditions for deleting bandwidth profile can be:

•Invalid AID. If the AID is invalid, an IIAC (Invalid AID) error message is returned.

•The "ALL" AID is invalid for this command.

•The BWP having the specified AID should be present in the node, that is, already been entered by ENT-BWP-ETH command.

Category

ETHERNET

Security

Provisioning

Input Format

ED-BWP-ETH:[<TID>]:<AID>:<CTAG>:::[NAME=<NAME>],[CIR=<CIR>],[CBS=<CBS>],[PBS=<PBS>],[PIR=<PIR>],[CFMSTATE=<CFM_STATE>][:];

Input Example

ED-BWP-ETH:ROCKS:BWP-10000:1:::NAME="MyBWP",CIR=10,CBS=1M,PBS=1M,PIR=20,CFMSTATE=Y;

Input Parameters

<AID>	This AID is used to access BWP.BWP AID Format is: BWP-[bwpid]Values
•BWP-ALL	All aid for BWP.
•BWP-{1-10000}	Single AID for BWP. The valid identifiers ranges from 1 to 10000.
<NAME>	indicates the BWP name. bwp name is a String. - Default value is -
<CIR>	Ingress committed information rate. This is a value between 0 and 100.Default value is - 100.
<CBS>	Ingress committed burst bucket size.
•4K	4 Kbit bucket size
•8K	16 Kbit bucket size
•16K	32 Kbit bucket size
•32K	64 Kbit bucket size
•64K	128 Kbit bucket size
•128K	256 Kbit bucket size
•256K	512 Kbit bucket size
•512K	1 Mbit bucket size
•1M	2 Mbit bucket size
•2M	4 Mbit bucket size
•4M	8 Mbit bucket size
•8M	16 Mbit bucket size
•16M	16 Kbit bucket size
<EBS>	Ingress peak burst bucket size
•4K	4 Kbit bucket size
•8K	8 Kbit bucket size
•16K	16 Kbit bucket size
•32K	32 Kbit bucket size
•64K	64 Kbit bucket size
•128K	128 Kbit bucket size
•256K	256 Kbit bucket size
•512K	512 Kbit bucket size
•1M	1 Mbit bucket size
•2M	2 Mbit bucket size
•4M	4 Mbit bucket size
•8M	8 Mbit bucket size
•16M	16 Mbit bucket size
<PIR>	Excess information rate. This is a value between 0 and 100. Default value is - 100.
<CFMSTATE>	Link Integrity status
•Y	Enabled
•N	Disabled

11.13  ED-CMD-SECU

(Cisco ONS 15454, 15327, 15600, 15310) The Edit Command Security (ED-CMD-SECU) command edits the command security level of a particular command.

Usage Guidelines

None

Category

Security

Security

Superuser

Input Format

ED-CMD-SECU:[<TID>]:<AID>:<CTAG>::<CAP>;

Input Example

ED-CMD-SECU::INIT-REG:1::SUPER;

Input Parameters

<AID>	Access identifier string. Identifies the entity in the NE to which the command pertains. It is the command verb along with verb modifier(s), as it currently exists. It can be a single command or a block of commands, where the block might include all commands. Only INIT-REG will be supported. String. Must not be null.
<CAP>	Command access privilege. Must not be null. The parameter type is PRIVILEGE, which is the security level.
•PROV	Provision security level. 60 minutes of idle time.
•SUPER	Superuser security level. 15 minutes of idle time.

11.14  ED-COS-ETH

(Cisco ONS 15454) The Edit Ethernet Cost of Service Table (ED-COS-ETH) command edits the egress parameter of a cost of service table associated to an L2 Ethernet port.

Usage Guidelines

The default values for all optional parameters are NE default values, but these values might not be the current value for a parameter. Use a retrieve command to obtain the current value.

Category