Table Of Contents

RST Commands

20.1  RST-<MOD2>

20.2  RST-EQPT

RST Commands

---

This chapter provides RST (restore) commands for the Cisco ONS 15454, ONS 15327, ONS 15600 and ONS 15310-CL.

20.1  RST-<MOD2>

Restore (10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, CLNT, D1VIDEO, DS1, DV6000, E1, E3, E4, EC1, ESCON, ETRCLO, FSTE, G1000, GFPOS, GIGE, HDTV, ISC1, OC12, OC192, OC3, OC48, OCH, OMS, OTS, POS, STS1, STS12C, STS18C, STS192C, STS24C, STS36C, STS3C, STS48C, STS6C, STS9C, T1, T3, VC12, VC3, VT1, VT2)

Usage Guidelines

Cisco ONS 15454, ONS 15327, ONS 15600, ONS 15310-CL

This command provisions a facility in service.

See Table 27-1 on page 27-1 for supported modifiers by platform.

---

Note This command can only be executed when the port is in OOS,MT state.

---

Category

Facility

Security

Maintenance

Related Commands

DLT-<MOD1PAYLOAD> DLT-FFP-<MOD2DWDMPAYLOAD> DLT-FFP-<OCN_TYPE> ED-<GIGE_TYPE> ED-<MOD1FCPAYLOAD> ED-<MOD1FICONPAYLOAD> ED-<MOD2DWDMPAYLOAD> ED-<OCN_TYPE> ED-ALS ED-DS1 ED-EC1 ED-FFP-<MOD2DWDMPAYLOAD> ED-FFP-<OCN_TYPE> ED-FSTE ED-G1000 ED-GFP ED-HDLC ED-POS ED-T1 ED-T3 ED-TRC-<MOD2DWDMPAYLOAD> ED-TRC-<OCN_TYPE> ENT-<MOD1PAYLOAD> ENT-FFP-<MOD2DWDMPAYLOAD> ENT-FFP-<OCN_TYPE> INIT-REG-<MOD2> OPR-ALS OPR-LPBK-<MOD2> OPR-PROTNSW-<MOD2DWDMPAYLOAD> OPR-PROTNSW-<OCN_TYPE> REPT PM <MOD2> RLS-PROTNSW-<MOD2DWDMPAYLOAD>

RLS-PROTNSW-<OCN_TYPE> RMV-<MOD2> RTRV-<MOD1FCPAYLOAD> RTRV-<MOD1FICONPAYLOAD> RTRV-<MOD2DWDMPAYLOAD> RTRV-<OCN_TYPE> RTRV-10GIGE RTRV-ALMTH-<MOD2> RTRV-ALS RTRV-DS1 RTRV-EC1RTRV-FAC RTRV-FFP-<MOD2DWDMPAYLOAD> RTRV-FFP-<OCN_TYPE> RTRV-FSTE RTRV-G1000 RTRV-GFP RTRV-GIGE RTRV-HDLC RTRV-PM-<MOD2> RTRV-PMSCHED-<MOD2> RTRV-POS RTRV-PROTNSW-<MOD2DWDMPAYLOAD> RTRV-PROTNSW-<OCN_TYPE> RTRV-T1 RTRV-T3 RTRV-TH-<MOD2> RTRV-TRC-<MOD2DWDMPAYLOAD> RTRV-TRC-<OCN_TYPE> SCHED-PMREPT-<MOD2> SET-ALMTH-<MOD2> SET-TH-<MOD2>

Input Format

RST-<MOD2>:[<TID>]:<AID>:<CTAG>::::[<PST>[,<sst>]];

Input Example

RST-EC1:CISCO:FAC-1-1:1::::IS,AINS;

Input Parameters

Table 20-1 RST-<MOD2> Input Parameters 

Parameter and Values	Description
AID	Access identifier from the "25.1.1  ALL" section on page 25-1
PST	Primary state. Defaults to IS Parameter type is PST—indicates the current overall service condition of an entity
•IS	In service
•OOS	Out of service
SST	Secondary state. Defaults to AINS Parameter type is SST—provides additional information pertaining to PST and PSTQ
•AINS	Automatic in service
•DSBLD	Disabled
•LPBK	Loopback
•MEA	Mismatch of equipment and attributes
•MT	Maintenance mode
•OOG	Out of group
•SWDL	Software downloading
•UAS	Unassigned
•UEQ	Unequipped

20.2  RST-EQPT

Restore Equipment

Usage Guidelines

Cisco ONS 15454, ONS 15327, ONS 15600, ONS 15310-CL

This command provisions equipment into the IS state from the MT state.

---

Note Only applicable to equipment that is in transition from the MT state to the IS state.

---

Category

Equipment

Security

Maintenance

Related Commands

ALW-SWDX-EQPT ALW-SWTOPROTN-EQPT ALW-SWTOWKG-EQPT CHG-EQPT DLT-EQPT ED-EQPT ENT-EQPT INH-SWDX-EQPT INH-SWTOPROTN-EQPT INH-SWTOWKG-EQPT REPT ALM EQPT REPT EVT EQPT

REPT RMV EQPT REPT RST EQPT RMV-EQPT RTRV-ALM-EQPT RTRV-ALMTH-EQPT RTRV-COND-EQPT RTRV-EQPT SET-ALMTH-EQPT SW-DX-EQPT SW-TOPROTN-EQPT SW-TOWKG-EQPT

Input Format

RST-EQPT:[<TID>]:<AID>:<CTAG>[::];

Input Example

RST-EQPT:CISCO:SLOT-1:1;

Input Parameters

Table 20-2 RST-EQPT Input Parameters 

Parameter and Values	Description
AID	Access identifier from the "25.1.13  EQPT" section on page 25-27