Table Of Contents

RMV Commands

19.1  RMV-<MOD2>

19.2  RMV-EQPT

RMV Commands

---

This chapter provides RMV (remove) commands for the Cisco ONS 15454, ONS 15327, ONS 15600 and ONS 15310-CL.

19.1  RMV-<MOD2>

Remove (10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, CLNT, D1VIDEO, DS1, DV6000, E1, E3, E4, EC1, ESCON, ETRCLO, FSTE, G1000, GFPOS, GIGE, HDTV, ISC1, OC12, OC192, OC3, OC48, OCH, OMS, OTS, POS, STS1, STS12C, STS18C, STS192C, STS24C, STS36C, STS3C, STS48C, STS6C, STS9C, T1, T3, VC12, VC3, VT1, VT2)

Usage Guidelines

Cisco ONS 15454, ONS 15327, ONS 15600, ONS 15310-CL

This command removes a facility from service.

See Table 27-1 on page 27-1 for supported modifiers by platform.

Category

Facility

Security

Maintenance

Related Commands

DLT-<MOD1PAYLOAD> DLT-FFP-<MOD2DWDMPAYLOAD> DLT-FFP-<OCN_TYPE> ED-<GIGE_TYPE> ED-<MOD1FCPAYLOAD> ED-<MOD1FICONPAYLOAD> ED-<MOD2DWDMPAYLOAD> ED-<OCN_TYPE> ED-ALS ED-DS1 ED-EC1 ED-FFP-<MOD2DWDMPAYLOAD> ED-FFP-<OCN_TYPE> ED-FSTE ED-G1000 ED-GFP ED-HDLC ED-POS ED-T1 ED-T3 ED-TRC-<MOD2DWDMPAYLOAD> ED-TRC-<OCN_TYPE> ENT-<MOD1PAYLOAD> ENT-FFP-<MOD2DWDMPAYLOAD> ENT-FFP-<OCN_TYPE> INIT-REG-<MOD2> OPR-ALS OPR-LPBK-<MOD2> OPR-PROTNSW-<MOD2DWDMPAYLOAD> OPR-PROTNSW-<OCN_TYPE> REPT PM <MOD2> RLS-PROTNSW-<MOD2DWDMPAYLOAD>

RLS-PROTNSW-<OCN_TYPE> RST-<MOD2> RTRV-<MOD1FCPAYLOAD> RTRV-<MOD1FICONPAYLOAD> RTRV-<MOD2DWDMPAYLOAD> RTRV-<OCN_TYPE> RTRV-10GIGE RTRV-ALMTH-<MOD2> RTRV-ALS RTRV-DS1 RTRV-EC1RTRV-FAC RTRV-FFP-<MOD2DWDMPAYLOAD> RTRV-FFP-<OCN_TYPE> RTRV-FSTE RTRV-G1000 RTRV-GFP RTRV-GIGE RTRV-HDLC RTRV-PM-<MOD2> RTRV-PMSCHED-<MOD2> RTRV-POS RTRV-PROTNSW-<MOD2DWDMPAYLOAD> RTRV-PROTNSW-<OCN_TYPE> RTRV-T1 RTRV-T3 RTRV-TH-<MOD2> RTRV-TRC-<MOD2DWDMPAYLOAD> RTRV-TRC-<OCN_TYPE> SCHED-PMREPT-<MOD2> SET-ALMTH-<MOD2> SET-TH-<MOD2>

Input Format

RMV-<MOD2>:[<TID>]:<AID>:<CTAG>[::];

Input Example

RMV-EC1:CISCO:FAC-1-1:1;

Input Parameters

Table 19-1 RMV-<MOD2> Input Parameters 

Parameter and Values	Description
AID	Access identifier from the "25.1.1  ALL" section on page 25-1

19.2  RMV-EQPT

Remove Equipment

Usage Guidelines

Cisco ONS 15454, ONS 15327, ONS 15600, ONS 15310-CL

This command removes equipment from the IS state and places it into the MT state.

---

Note Only applicable to equipment that is in transition from the IS state to the MT state.

---

Category

Equipment

Security

Maintenance

Related Commands

ALW-SWDX-EQPT ALW-SWTOPROTN-EQPT ALW-SWTOWKG-EQPT CHG-EQPT DLT-EQPT ED-EQPT ENT-EQPT INH-SWDX-EQPT INH-SWTOPROTN-EQPT INH-SWTOWKG-EQPT REPT ALM EQPT REPT EVT EQPT

REPT RMV EQPT REPT RST EQPT RST-EQPT RTRV-ALM-EQPT RTRV-ALMTH-EQPT RTRV-COND-EQPT RTRV-EQPT SET-ALMTH-EQPT SW-DX-EQPT SW-TOPROTN-EQPT SW-TOWKG-EQPT

Input Format

RMV-EQPT:[<TID>]:<AID>:<CTAG>[::];

Input Example

RMV-EQPT:CISCO:SLOT-1:1;

Input Parameters

Table 19-2 RMV-EQPT Input Parameters 

Parameter and Values	Description
AID	Access identifier from the "25.1.13  EQPT" section on page 25-27