-
Cisco ONS SONET TL1 Command Guide, Release 6.0
-
About This Guide
-
Chapter 1, ACT Commands
-
Chapter 2, ALW Commands
-
Chapter 3, APPLY Commands
-
Chapter 4, CANC Commands
-
Chapter 5, CHG Commands
-
Chapter 6, CLR Commands
-
Chapter 7, CONN Commands
-
Chapter 8, COPY Commands
-
Chapter 9, DISC Commands
-
Chapter 10, DLT Commands
-
Chapter 11, ED Commands
-
Chapter 12, ENT Commands
-
Chapter 13, EX Commands
-
Chapter 14, INH Commands
-
Chapter 15, INIT Commands
-
Chapter 16, OPR Commands
-
Chapter 17, REPT Messages
-
Chapter 18, RLS Commands
-
Chapter 19, RMV Commands
-
Chapter 20, RST Commands
-
Chapter 21, RTRV Commands
-
Chapter 22, SCHED Commands
-
Chapter 23, SET Commands
-
Chapter 24, SW Commands
-
Chapter 25, Access Identifiers
-
Chapter 26, Conditions
-
Chapter 27, Modifiers
-
Table Of Contents
11.19 ED-FFP-<MOD2DWDMPAYLOAD>
ED Commands
Note
The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration. Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's path protection feature, which may be used in any topological network configuration. Cisco does not recommend using its path protection feature in any particular topological network configuration.
This chapter provides ED (edit) commands for the Cisco ONS 15454, ONS 15327, ONS 15600 and ONS 15310-CL.
11.1 ED-<GIGE_TYPE>
Edit (10GIGE, GIGE)
Usage Guidelines
Cisco ONS 15454, ONS 15600
This command edits Ethernet facility attributes.
See Table 27-1 on page 27-1 for supported modifiers by platform.
Ports
Provisioning
Related Commands
ED-<GIGE_TYPE>:[<TID>]:<AID>:<CTAG>:::[NAME=<NAME>],[MACADDR=<MACADDR>],
[CMDMDE=<CMDMDE>],[FREQ=<FREQ>],[LOSSB=<LOSSB>]:[<PST>[,<SST>]];ED-GIGE:CISCO:FAC-1-1:123:::NAME="GIGE PORT",
MACADDR=00-0E-AA-BB-CC-FF,CMDMDE=CMDMDE,FREQ=1550,LOSSB=SX:IS,AINS;Input Parameters
Table 11-1 ED-<GIGE_TYPE> Input Parameters
AID
Access identifier from the "25.1.14 FACILITY" section on page 25-28
NAME
Port name. String. Defaults to NULL. Maximum length is 32 characters
MACADDR
String. Defaults to NULL. Maximum length is 18 characters
CMDMDE
Command execution mode. NORM for normal (default) and FRCD for forced. FRCD will override any safeguards that normally reject a request to delete an in service resource
Parameter type is CMDMDE—forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied
•
Force the system to override a state where the command would normally be denied
•
Execute the command normally. Do not override any conditions that might make the command fail
FREQ
Parameter type is OPTICAL-WLEN—optical wavelength
•
Wavelength 1
•
Wavelength 2
•
Wavelength 3
•
Wavelength 4
•
Wavelength 5
•
Wavelength 6
•
Wavelength 7
•
Wavelength 8
•
Wavelength 9
•
Wavelength 10
•
Wavelength 11
•
Wavelength 12
•
Wavelength 13
•
Wavelength 14
•
Wavelength 15
•
Wavelength 16
•
Wavelength 17
•
Wavelength 18
•
Wavelength 19
•
Wavelength 20
•
Wavelength 21
•
Wavelength 22
•
Wavelength 23
•
Wavelength 24
•
Wavelength 25
•
Wavelength 26
•
Wavelength 27
•
Wavelength 28
•
Wavelength 29
•
Wavelength 30
•
Wavelength 31
•
Wavelength 32
•
Use Tunable Wavelength 1
LOSSB
Parameter type is REACH—reach values
•
Autoprovisioning
•
Reach CX
•
Reach DX
•
Reach HX
•
Reach I1
•
Reach IR-1
•
Reach IR-2
•
Reach L1
•
Reach L2
•
Reach L3
•
Reach LR-1
•
Reach LR-2
•
Reach LR-3
•
Reach LX
•
Reach S1
•
Reach S2
•
Reach SR
•
Reach SR-1
•
Reach SX
•
Reach T
•
Reach VX
•
Reach ZX
PST
Primary state
Parameter type is PST—indicates the current overall service condition of an entity
•
In service
•
Out of service
SST
Secondary state
Parameter type is SST—provides additional information pertaining to PST and PSTQ
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.2 ED-<MOD1FCPAYLOAD>
Edit (1GFC, 2GFC, ESCON)
Usage Guidelines
Cisco ONS 15454
See Table 27-1 on page 27-1 for supported modifiers by platform.
This command edits the attributes related to the Fibre Channel (FC) facility. The state IS,AINS is not supported on the FC port.
Note
•
•
Ports
Provisioning
Related Commands
ED-<MOD1FCPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[LINKRCVRY=<LINKRCVRY>],
[DISTEXTN=<DISTEXTN>],[AUTODETECTION=<AUTODETECTION>],
[LINKCREDITS=<LINKCREDITS>],[MFS=<MFS>],[NAME=<NAME>],
[CMDMDE=<CMDMDE>],[SOAK=<SOAK>],[FREQ=<FREQ>],
[LOSSB=<LOSSB>]:[<PST>[,[<SST>]];ED-1GFC:CISCO:FAC-6-1:1:::LINKRCVRY=Y,DISTEXTN=NONE,AUTODETECTION=Y,
LINKCREDITS=10,MFS=2148,NAME="FC PORT",CMDMDE=CMDMDE,SOAK=32,
FREQ=1550,LOSSB=LR-1:OOS,MT;Input Parameters
Table 11-2 ED-<MOD1FCPAYLOAD> Input Parameters
AID
Access identifier from the "25.1.14 FACILITY" section on page 25-28
LINKRCVRY
Link recovery
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
DISTEXTN
Distance extension. It can be set to Buffer-to-Buffer (B2B) Credit Management state or None.
Note
Parameter type is DISTANCE_EXTENSION—distance extension
•
Buffer to buffer flow control
•
No distance extension
AUTODETECTION
Autodetection. Turns autodetection on or off
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
LINKCREDITS
Number of link credits. If autodetection is set to off the value of the link credits will be used to configure the hardware. Integer
MFS
Maximum frame size. Integer
NAME
String
CMDMDE
Command execution mode, forced or normal. FRCD deletes all the VCG members and member cross-connects of a VCG
Parameter type is CMDMDE—forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied
•
Force the system to override a state where the command would normally be denied
•
Execute the command normally. Do not override any conditions that might make the command fail
SOAK
OOS-AINS to IS transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). Integer
FREQ
Parameter type is OPTICAL-WLEN—optical wavelength
•
Wavelength 1
•
Wavelength 2
•
Wavelength 3
•
Wavelength 4
•
Wavelength 5
•
Wavelength 6
•
Wavelength 7
•
Wavelength 8
•
Wavelength 9
•
Wavelength 10
•
Wavelength 11
•
Wavelength 12
•
Wavelength 13
•
Wavelength 14
•
Wavelength 15
•
Wavelength 16
•
Wavelength 17
•
Wavelength 18
•
Wavelength 19
•
Wavelength 20
•
Wavelength 21
•
Wavelength 22
•
Wavelength 23
•
Wavelength 24
•
Wavelength 25
•
Wavelength 26
•
Wavelength 27
•
Wavelength 28
•
Wavelength 29
•
Wavelength 30
•
Wavelength 31
•
Wavelength 32
•
Use Tunable Wavelength 1
LOSSB
Parameter type is REACH—reach values
•
Autoprovisioning
•
Reach CX
•
Reach DX
•
Reach HX
•
Reach I1
•
Reach IR-1
•
Reach IR-2
•
Reach L1
•
Reach L2
•
Reach L3
•
Reach LR-1
•
Reach LR-2
•
Reach LR-3
•
Reach LX
•
Reach S1
•
Reach S2
•
Reach SR
•
Reach SR-1
•
Reach SX
•
Reach T
•
Reach VX
•
Reach ZX
PST
Primary state
Parameter type is PST—indicates the current overall service condition of an entity
•
In service
•
Out of service
SST
Secondary state
Parameter type is SST—provides additional information pertaining to PST and PSTQ
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.3 ED-<MOD1FICONPAYLOAD>
Edit (1GFICON, 2GFICON, ESCON)
Usage Guidelines
Cisco ONS 15454
See Table 27-1 on page 27-1 for supported modifiers by platform.
This command edits the attributes related with the FICON payload facility. The state IS,AINS is not supported on the FICON port.
Ports
Provisioning
Related Commands
ED-<MOD1FICONPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[LINKRCVRY=<LINKRCVRY>],
[DISTEXTN=<DISTEXTN>],[AUTODETECTION=<AUTODETECTION>],
[LINKCREDITS=<LINKCREDITS>],[MFS=<MFS>],[NAME=<NAME>],
[CMDMDE=<CMDMDE>],[SOAK=<SOAK>],[FREQ=<FREQ>],
[LOSSB=<LOSSB>]:[<PST>[,<SST>]];ED-1GFICON:CISCO:FAC-6-1:1:::LINKRCVRY=Y,DISTEXTN=NONE,AUTODETECTION=Y,
LINKCREDITS=10,MFS=2148,NAME="FC PORT",CMDMDE=CMDMDE,SOAK=32,FREQ=1550,
LOSSB=LR-1:OOS,MT;Input Parameters
Table 11-3 ED-<MOD1FICONPAYLOAD> Input Parameters
AID
Access identifier from the "25.1.14 FACILITY" section on page 25-28
LINKRCVRY
Link recovery
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
DISTEXTN
Distance extension. It can be set to Buffer-to-Buffer (B2B) Credit Management state or None.
Note
Parameter type is DISTANCE_EXTENSION—distance extension
•
Buffer to buffer flow control
•
No distance extension
AUTODETECTION
Autodetection. Turns autodetection on or off
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
LINKCREDITS
Number of link credits. If autodetection is set to off the value of the link credits will be used to configure the hardware. Integer
MFS
Maximum frame size. Integer
NAME
String
CMDMDE
Command execution mode, forced or normal. FRCD deletes all the VCG members and member cross-connects of a VCG
Parameter type is CMDMDE—forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied
•
Force the system to override a state where the command would normally be denied
•
Execute the command normally. Do not override any conditions that might make the command fail
SOAK
OOS-AINS to IS transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). Integer
FREQ
Parameter type is OPTICAL-WLEN—optical wavelength
•
Wavelength 1
•
Wavelength 2
•
Wavelength 3
•
Wavelength 4
•
Wavelength 5
•
Wavelength 6
•
Wavelength 7
•
Wavelength 8
•
Wavelength 9
•
Wavelength 10
•
Wavelength 11
•
Wavelength 12
•
Wavelength 13
•
Wavelength 14
•
Wavelength 15
•
Wavelength 16
•
Wavelength 17
•
Wavelength 18
•
Wavelength 19
•
Wavelength 20
•
Wavelength 21
•
Wavelength 22
•
Wavelength 23
•
Wavelength 24
•
Wavelength 25
•
Wavelength 26
•
Wavelength 27
•
Wavelength 28
•
Wavelength 29
•
Wavelength 30
•
Wavelength 31
•
Wavelength 32
•
Use Tunable Wavelength 1
LOSSB
Parameter type is REACH—reach values
•
Autoprovisioning
•
Reach CX
•
Reach DX
•
Reach HX
•
Reach I1
•
Reach IR-1
•
Reach IR-2
•
Reach L1
•
Reach L2
•
Reach L3
•
Reach LR-1
•
Reach LR-2
•
Reach LR-3
•
Reach LX
•
Reach S1
•
Reach S2
•
Reach SR
•
Reach SR-1
•
Reach SX
•
Reach T
•
Reach VX
•
Reach ZX
PST
Primary state
Parameter type is PST—indicates the current overall service condition of an entity
•
In service
•
Out of service
SST
Secondary state
Parameter type is SST—provides additional information pertaining to PST and PSTQ
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.4 ED-<MOD2DWDMPAYLOAD>
Edit (10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, D1VIDEO, DV6000, ESCON,ETRCLO, GIGE, HDTV, ISC1, ISC3, PASSTHRU)
Usage Guidelines
Cisco ONS 15454
See Table 27-1 on page 27-1 for supported modifiers by platform.
This command edits the operating parameters for a DWDM client facility.
DWDM
Provisioning
Related Commands
ED-<MOD2DWDMPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[NAME=<NAME>],
[CMDMDE=<CMDMDE>],[FREQ=<FREQ>],[LOSSB=<LOSSB>]:[<PST>[,<SST>]];ED-HDTV::FAC-1-1:1:::NAME="PORTNAME",CMDMDE=CMDMDE,FREQ=1550,
LOSSB=LR-1:IS,AINS;Input Parameters
Table 11-4 ED-<MOD2DWDMPAYLOAD> Input Parameters
AID
Access identifier from the "25.1.14 FACILITY" section on page 25-28
LINKCREDITS
Number of link credits. If autodetection is set to off the value of the link credits will be used to configure the hardware. Integer
NAME
String
CMDMDE
Command execution mode, forced or normal. FRCD deletes all the VCG members and member cross-connects of a VCG
Parameter type is CMDMDE—forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied
•
Force the system to override a state where the command would normally be denied
•
Execute the command normally. Do not override any conditions that might make the command fail
FREQ
Parameter type is OPTICAL-WLEN—optical wavelength
•
Wavelength 1
•
Wavelength 2
•
Wavelength 3
•
Wavelength 4
•
Wavelength 5
•
Wavelength 6
•
Wavelength 7
•
Wavelength 8
•
Wavelength 9
•
Wavelength 10
•
Wavelength 11
•
Wavelength 12
•
Wavelength 13
•
Wavelength 14
•
Wavelength 15
•
Wavelength 16
•
Wavelength 17
•
Wavelength 18
•
Wavelength 19
•
Wavelength 20
•
Wavelength 21
•
Wavelength 22
•
Wavelength 23
•
Wavelength 24
•
Wavelength 25
•
Wavelength 26
•
Wavelength 27
•
Wavelength 28
•
Wavelength 29
•
Wavelength 30
•
Wavelength 31
•
Wavelength 32
•
Use Tunable Wavelength 1
LOSSB
Parameter type is REACH—reach values
•
Autoprovisioning
•
Reach CX
•
Reach DX
•
Reach HX
•
Reach I1
•
Reach IR-1
•
Reach IR-2
•
Reach L1
•
Reach L2
•
Reach L3
•
Reach LR-1
•
Reach LR-2
•
Reach LR-3
•
Reach LX
•
Reach S1
•
Reach S2
•
Reach SR
•
Reach SR-1
•
Reach SX
•
Reach T
•
Reach VX
•
Reach ZX
PST
Primary state
Parameter type is PST—indicates the current overall service condition of an entity
•
In service
•
Out of service
SST
Secondary state
Parameter type is SST—provides additional information pertaining to PST and PSTQ
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.5 ED-<MOD_PATH>
Edit (STS1, STS12C, STS18C, STS192C, STS24C, STS36C, STS3C, STS48C, STS6C, STS9C, VC12, VC3, VT1, VT2)
This command edits the attributes associated with STS and VT paths.
Usage Guidelines
Cisco ONS 15454, 15327, 15600, 15310
The SFBER, SDBER, RVRTV, and RVTM parameters only apply to path protection at the STS path level and ONS 15310_CL and ONS 15454 VT paths.
SFBER and SDBER also apply to the VT path level on the ONS 15310-CL and ONS 15454 when the ONS 15454 has an XC-VXC-10G card.
SWPDIP does not apply to the VT path level (VT1 and VT2).
The path trace message is a 64 character string including the terminating CR (carriage return) and LF (line feed) that is transported in the J1 byte of the SONET STS Path overhead. Both the EXPTRC and TRC string can be provisioned by user with up to 62 character string.
The EXPTRC indicates the contents of the expected incoming path trace are provisioned by the user. The TRC indicates the contents of the outgoing path trace message. The INCTRC indicates the contents of the incoming path trace message.
The path trace mode has three modes: OFF, MANUAL, and AUTO. The path trace mode defaults to OFF. The MANUAL mode performs the comparison of the received string with the user-entered expected string. The AUTO mode performs the comparison of the present received string with an expected string set to a previously received string. If there is a mismatch, TIM-P alarm is raised. When the path trace is in OFF mode, there is no path trace processing, and all the alarm and state conditions are reset.
The TACC parameter edits an existing single STS or VT and changes it to a test access point. When an editing command on TACC is executed, it assigns the STS or VT for the first 2-way connection and STS+1 as the second 2-way connection. For single FAD test access only a single STS/VT is used for the TAP creation. For more information on TACC, refer to the Cisco ONS SDH and Cisco ONS 15600 SDH TL1 Reference Guide.
J1 is implemented on the DS1/DS1N, DS3E/DS3NE, DS3XM, EC1, OC3, OC12-4, OC48AS and OC192 cards.
DS3/DS3N, OC12, OC48, E100, and E1000 cards do not support path trace.
DS1/DS1N, DS3E/DS3NE, and DS3XM support both TRC and EXPTRC in the ED-STS-PATH command.
EC1, OC3, OC48AS, and OC192 only support EXPTRC in the ED-STS-PATH command.
Note
The following actions will produce error messages:
1.
2.
3.
4.
5.
Note
•
•
•
•
•
•
–
–
–
•
•
•
•
For TACC creation, use the ED-STS3C command because the TACC path width (like the cross-connect) has to be 3C on the DS3I card. In this case, you are creating a new entity (TAP) on the DS3I card that has to be of 3C width. On the DS3I card the ED0STS command can be used either with STS1 or STS3C depending on the parameter to be modified.
•
•
•
•
•
Paths
Provisioning
Related Commands
ED-<MOD_PATH>:[<TID>]:<AID>:<CTAG>:::[SFBER=<SFBER>],[SDBER=<SDBER>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[SWPDIP=<SWPDIP>],
[HOLDOFFTIMER=<HOLDOFFTIMER>],[EXPTRC=<EXPTRC>],[TRC=<TRC>],
[TRCMODE=<TRCMODE>],[TRCFORMAT=<TRCFORMAT>][TACC=<TACC>],
[TAPTYPE=<TAPTYPE>],[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];ED-STS3C:FERNDALE:STS-2-1-4:115:::SFBER=1E-3,SDBER=1E-5,RVRTV=Y,RVTM=1.0,
SWPDIP=Y,HOLDOFFTIMER=2000,EXPTRC="EXPTRCSTRING",TRC="TRCSTRING",
TRCMODE=OFF,TRCFORMAT=64-BYTE,TACC=8,TAPTYPE=SINGLE,
CMDMDE=CMDMDE:IS,AINS;
Table 11-5 ED-<MOD_PATH> Input Parameters
AID
Access identifier from the "25.1.10 CrossConnectId1" section on page 25-20
SFBER
Signal failure threshold. Applies only to path protection. Applies to STS-level paths in SONET (STSn) and to VT-level paths on the ONS 15310-CL with an XC-VXC-10G card. Defaults to 1E-4
Parameter type is SF_BER—the threshold for declaring signal failure on a facility or path
•
SFBER is 1E-3
•
SFBER is 1E-4
•
SFBER is 1E-5
SDBER
Signal degrade threshold. Applies only to path protection. Applies to STS-level paths in SONET (STSn) and to VT-level paths on the ONS 15310-CL with an XC-VXC-10G card. 1E-9 is not allowed for VT-level/LO paths. Defaults to 1E-6
Parameter type is SD_BER—the threshold for declaring signal degrade on a facility or path
•
SDBER is 1E-5
•
SDBER is 1E-6
•
SDBER is 1E-7
•
SDBER is 1E-8
•
SDBER is 1E-9
RVRTV
Revertive mode. The value Y indicates that the protection switching system reverts service to the original line after restoration. The value N indicates that the protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. Only applies to path protection
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
RVTM
Revertive time. RVTM is not allowed to be set while "RVRTV" is N. Only applies to path protection
Parameter type is REVERTIVE_TIME—revertive time
•
Revertive time is 0.5 to 12.0 minutes
SWPDIP
On-off switch for path protection payload defect level switching. Applicable only to STS-level paths in SONET (STSn). For the selector path on a BLSR, SWPDIP is not editable and always ON. Defaults to N
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
HOLDOFFTIMER
Hold off timer for path protection DRI. Values must be within 0 and 10000 ms (0 - 10 seconds), with increments of 100 ms. Defaults to "existed value." Integer
EXPTRC
Expected path trace content. Indicates the expected path trace message (J1) contents. EXPTRC is any 64-character ASCII string, including the terminating CR (carriage return) and LF (line feed). Applicable to STS-level paths in SONET (STSn). Applicable to VT-level paths for the DS3XM-12 and CE-100T-8 card on the ONS 15454 and the CE-100T-8 card on ONS 15310-CL. Defaults to 64 null characters. String
TRC
The path trace message to be transmitted. The trace byte (J1) continuously transmits a 64-byte, fixed length ASCII string, one byte at a time. A null value defaults to the NE transmitting 62 null characters (hex 00) and CR and LF. Applicable to STS-level paths in SONET (STSn). Applicable to VT-level paths for the DS3XM-12 and CE-100T-8 card on the ONS 15454 and the CE-100T-8 card on ONS 15310-CL. For ONS 15310-CL, TRC is not provisionable on the EC/OC ports. Defaults to 64 null characters. String
TRCMODE
Path trace mode. Applicable only to STS-level paths in SONET (STSn). Defaults to the OFF mode. ONS 15310-CL EC/OC ports do not support MAN and AUTO, but can be configured as MAN-NO-AIS and AUTO-NO-AIS.
Note
Parameter type is TRCMODE—trace mode
•
Use the previously received path trace string as the expected string. Not applicable to MXP/TXP cards
•
Use the previously received path trace string as the expected string and do not turn on AIS and RDI if TIM-P is detected
•
Use the provisioned expected string as the expected string
•
Use the provisioned expected string as the expected string and do not turn on AIS and RDI if TIM-P is detected
•
Turn off path trace capability. Nothing will be reported
TRCFORMAT
Path trace format. Only 64-byte is supported. Defaults to 64-byte
Parameter type is TRCFORMAT—trace format
•
64 byte trace message
TACC
TAP number within a range of 0 to 999. Indicates whether the digroup being provisioned is to be used as a test access digroup. When TACC is 0 (zero), the TAP is deleted. Integer
TAPTYPE
TAP type. Defaults to DUAL
Parameter type is TAPTYPE—test access point type
•
Dual FAD
•
Single FAD
CMDMDE
Command mode
Parameter type is CMDMDE—forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied. Defaults to NORM
•
Force the system to override a state where the command would normally be denied
•
Execute the command normally. Do not override any conditions that might make the command fail
PST
Primary state. Defaults to IS
Parameter type is PST—indicates the current overall service condition of an entity
•
In service
•
Out of service
SST
Secondary state. Defaults to AINS
Parameter type is SST—provides additional information pertaining to PST and PSTQ
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.6 ED-<MOD_RING>
Edit Bidirectional Line Switched Ring
Usage Guidelines
Cisco ONS 15454, ONS 15327, ONS 15600
This command edits the BLSR attributes.
ONS 15327 and ONS 15600 do not support four-fiber BLSR.
The RVRTV, RVTM, SRVRTV, SRVTM, NODEID, and RINGID attributes can be edited for the four-fiber BLSR.
The RVRTV, RVTM, NODEID, and RINGID attributes can be edited for the two-Fiber BLSR.
The following actions will produce errors:
•
•
•
•
•
•
•
•
•
•
Note
•
BLSR
Provisioning
Related Commands
ED-<MOD_RING>:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>],[NODEID=<NODEID>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[SRVRTV=<SRVRTV>],[SRVTM=<SRVTM>][:];ED-BLSR:PETALUMA:BLSR-43:123:::RINGID=43,NODEID=3,RVRTV=Y,RVTM=2.0,
SRVRTV=Y,SRVTM=5.0;
Table 11-6 ED-<MOD_RING> Input Parameters
AID
Access identifier from the "25.1.3 AidUnionId1" section on page 25-12. Identifies the BLSR of the NE. ALL or BLSR-ALL AID is not allowed for editing a BLSR
RINGID
The BLSR ID of the NE up to six characters. Valid characters are A-Z and 0-9. String
NODEID
The BLSR node ID of the NE. NODEID ranges from 0 to 31. Integer
RVRTV
Revertive mode. The value Y indicates that the protection switching system reverts service to the original line after restoration. The value N indicates that the protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
RVTM
Revertive time. RVTM is not allowed to be set while "RVRTV" is N
Parameter type is REVERTIVE_TIME—revertive time
•
Revertive time is 0.5 to 12.0 minutes
SRVRTV
The span revertive mode for four-fiber BLSR only
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
SRVTM
The span revertive time for four-fiber BLSR only. SRVTM is not allowed to be set while SRVRTV is N
Parameter type is REVERTIVE_TIME—revertive time
•
Revertive time is 0.5 to 12.0 minutes
11.7 ED-<OCN_TYPE>
Edit (OC3, OC12, OC48, OC192)
Usage Guidelines
Cisco ONS 15454, 15327, 15600, 15310
See Table 27-1 on page 27-1 for supported modifiers by platform.
This command edits the attributes (for example, service parameters) and status of an OC-N facility. Allowable states for a facility are Out Of Service (OOS), Out Of Service with Automatic In Service transitioning (OOS-AINS), Out Of Service for Maintenance (OOS-MT), and In Service (IS).
The DCC transmit is bridged to both working and protect in a 1+1 protection scheme. On the receive side, the active one is selected for DCC. The DCC is provisioned on the working port only in a 1+1 protection scheme.
All lines in a 1+1 BLSR must have the same mode. If you change the mode of a line that is in a 1+1 BLSR, an error message will be returned.
UNI-C DCC provisioning notes:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Ports
Provisioning
Related Commands
ED-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>:::[DCC=<DCC>],[AREA=<AREA>],
[SYNCMSG=<SYNCMSG>],[SENDDUS=<SENDDUS>],[PJMON=<PJMON>],
[SFBER=<SFBER>],[SDBER=<SDBER>],[MODE=<MODE>],[MUX=<MUX>],
[SOAK=<SOAK>],[OSPF=<OSPF>],[LDCC=<LDCC>],[NAME=<NAME>],
[CMDMDE=<CMDMDE>],[EXPTRC=<EXPTRC>],[TRC=<TRC>],[TRCMODE=<TRCMODE>],
[TRCFORMAT=<TRCFORMAT>],[ADMSSM=<ADMSSM>],[SENDDUSFF=<SENDDUSFF>],
[AISONLPBK=<AISONLPBK>],[FREQ=<FREQ>],[LOSSB=<LOSSB>],
[FOREIGNFEND=<FOREIGNFEND>],[FOREIGNIP=<FOREIGNIP>]:[<PST>[,<SST>]];ED-OC48:PENNGROVE:FAC-6-1:114:::DCC=Y,AREA=10.92.63.1,SYNCMSG=N,
SENDDUS=N,PJMON=48,SFBER=1E-4,SDBER=1E-6,MODE=SONET,MUX=E2,SOAK=10,
OSPF=Y,LDCC=N,NAME="OCNPORT",CMDMDE=CMDMDE,EXPTRC="AAA",
TRC="AAA",TRCMODE=MAN,TRCFORMAT=16-BYTE,ADMSSM=PRS,SENDDUSFF=N,
AISONLPBK=AIS_ON_LPBK_ALL,FREQ=1550,LOSSB=LR-1,FOREIGNFEND=N,
FOREIGNIP="IP ADDRESS":IS,AINS;
Table 11-7 ED-<OCN_TYPE> Input Parameters
AID
Access identifier from the "25.1.14 FACILITY" section on page 25-28
DCC
Indicates whether or not the section DCC is to be used. Identifies the section DCC connection of the port
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
AREA
The area ID and shows up only if the DCC is enabled. String
SYNCMSG
Synchronization status message
Parameter type is EXT_RING—indicates if the ring supports the extended K1/K2/K3 protocol
•
The ring does not support the extended K1/K2/K3 protocol
•
The ring does support the extended K1/K2/K3 protocol
SENDDUS
The facility will send the DUS (Don't use for Synchronization) value as the sync status message for that facility
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
PJMON
Identifies an OC-N port PJMON. PJMON is an integer. It defaults to 0 (zero). Set a valid STS number of the optical port.
Note
SFBER
Signal failure threshold
Parameter type is SF_BER—the threshold for declaring signal failure on a facility or path
•
SFBER is 1E-3
•
SFBER is 1E-4
•
SFBER is 1E-5
SDBER
Signal degrade threshold
Parameter type is SD_BER—the threshold for declaring signal degrade on a facility or path
•
SDBER is 1E-5
•
SDBER is 1E-6
•
SDBER is 1E-7
•
SDBER is 1E-8
•
SDBER is 1E-9
MODE
OCn port mode
Parameter type is OPTICAL_MODE—the facility's optical mode
•
SDH/ETSI optical mode using European/International format
•
SONET/ANSI optical mode using the American format
MUX
BLSR extension byte (supported only on the OC48AS card). MUX cannot be configured if:
•
•
•
Parameter type is MUX_TYPE—BLSR extension type
•
E2 byte (orderwire)
•
F1 byte (user)
•
K3 byte
•
Z2 byte
SOAK
OOS-AINS to IS transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). Defaults to 32. Integer
OSFP
The open shortest path first discovery. Defaults to Y
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
LDCC
The line DCC connection on the port. Defaults to N
Parameter type is EXT_RING—indicates if the ring supports the extended K1/K2/K3 protocol
•
The ring does not support the extended K1/K2/K3 protocol
•
The ring does support the extended K1/K2/K3 protocol
NAME
String. Defaults to NULL. Maximum length is 32 characters
CMDMDE
Command Mode. The FRCD mode of operation is applicable to delete a VCAT member cross-connect from IS-NR or OOS-AU,AINS service state. Defaults to NORM
Parameter type is CMDMDE—forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied
•
Force the system to override a state where the command would normally be denied
•
Execute the command normally. Do not override any conditions that might make the command fail
EXPTRC
Expected path trace content. Indicates the expected path trace message (J1) contents. EXPTRC is any 64-character ASCII string, including the terminating CR (carriage return) and LF (line feed). Applicable to STS-level paths in SONET (STSn). Applicable to VT-level paths for the DS3XM-12 card on the ONS 15454. Defaults to NULL. String
TRC
The path trace message to be transmitted. The trace byte (J1) continuously transmits a 64-byte, fixed length ASCII string, one byte at a time. A null value defaults to the NE transmitting 62 null characters (hex 00) and CR and LF. Applicable to STS-level paths in SONET (STSn). Applicable to VT-level paths for the DS3XM-12 card on the ONS 15454. String
TRCMODE
Path trace mode. Applicable only to STS-level Paths in SONET (STSn). Defaults to MAN
Parameter type is TRCMODE—trace mode
•
Use the previously received path trace string as the expected string. Not applicable to MXP/TXP cards
•
Use the previously received path trace string as the expected string and do not turn on AIS and RDI if TIMP is detected
•
Use the provisioned expected string as the expected string
•
Use the provisioned expected string as the expected string and do not turn on AIS and RDI if TIMP is detected
•
Turn off path trace capability. Nothing will be reported
TRCFORMAT
Trace message size
Parameter type is TRCFORMAT—trace format
•
1 byte trace message
•
16 byte trace message
•
64 byte trace message
ADMSSM
SSM selectable value. It will only appear when SSM is disabled. Defaults to STU
Parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL—clock source quality level for SONET
•
Do Not Use For Synchronization
•
Primary Reference Source, Stratum 1 Traceable
•
Reserved For Network Synchronization Use
•
SONET Minimum Clock Traceable
•
Stratum 2 Traceable
•
Stratum 3 Traceable
•
Stratum 3E Traceable
•
Stratum 4 Traceable
•
Synchronized, Traceability Unknown
•
Transit Node Clock (2nd Generation Only)
SENDDUSFF
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
AISONLPBK
Parameter type is AIS_ON_LPBK—Indicates if AIS is sent on a loopback
•
AIS is sent on facility loopbacks
•
AIS is sent on all loopbacks
•
AIS is not sent on loopbacks
•
AIS is sent on terminal loopbacks
FREQ
Parameter type is OPTICAL-WLEN—optical wavelength
•
Wavelength 1
•
Wavelength 2
•
Wavelength 3
•
Wavelength 4
•
Wavelength 5
•
Wavelength 6
•
Wavelength 7
•
Wavelength 8
•
Wavelength 9
•
Wavelength 10
•
Wavelength 11
•
Wavelength 12
•
Wavelength 13
•
Wavelength 14
•
Wavelength 15
•
Wavelength 16
•
Wavelength 17
•
Wavelength 18
•
Wavelength 19
•
Wavelength 20
•
Wavelength 21
•
Wavelength 22
•
Wavelength 23
•
Wavelength 24
•
Wavelength 25
•
Wavelength 26
•
Wavelength 27
•
Wavelength 28
•
Wavelength 29
•
Wavelength 30
•
Wavelength 31
•
Wavelength 32
•
Use Tunable Wavelength 1
LOSSB
Parameter type is REACH—reach values
•
Autoprovisioning
•
Reach CX
•
Reach DX
•
Reach HX
•
Reach I1
•
Reach IR-1
•
Reach IR-2
•
Reach L1
•
Reach L2
•
Reach L3
•
Reach LR-1
•
Reach LR-2
•
Reach LR-3
•
Reach LX
•
Reach S1
•
Reach S2
•
Reach SR
•
Reach SR-1
•
Reach SX
•
Reach T
•
Reach VX
•
Reach ZX
FOREIGNFEND
Indicates whether the far-end NE on the DCC is a foreign NE
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
FOREIGNIP
The IP address of the far-end NE on the DCC. Used only if FOREIGNFEND is Y. String
PST
Primary state. Defaults to IS
Parameter type is PST—indicates the current overall service condition of an entity
•
In service
•
Out of service
SST
Secondary state. Defaults to AINS
Parameter type is SST—provides additional information pertaining to PST and PSTQ
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.8 ED-ALS
Edit Automatic Laser Shutdown
Usage Guidelines
Cisco ONS 15454, ONS 15310-CL
This command is used to modify the ALS attributes of an OC-N facility and all the facilities that support the ALS feature. For MXP_2.5G_10E, TXP_MR_10E, MXP_2.5G_10G, TXP_MR_10G, TXP_MR_2.5G, and TXPP_MR_2.5G cards this command is used to modify the ALS parameter of the OC48 and OC192 ports.
Ports
Provisioning
Related Commands
ED-ALS:[<TID>]:<SRC>:<CTAG>:::[ALSMODE=<ALSMODE>],[ALSRCINT=<ALSRCINT>],
[ALSRCPW=<ALSRCPW>][:];ED-ALS:CISCO:FAC-1-1:100:::ALSMODE=AUTO,ALSRCINT=130,ALSRCPW=35.1;
Table 11-8 ED-ALS Input Parameters
SRC
Access identifier from the "25.1.2 AidUnionId" section on page 25-9
ALSMODE
ALS is enabled or disabled
Parameter type is ALS_MODE—the working mode for automatic laser shutdown
•
Automatic
•
Disabled
•
Manual
•
Manual restart for test
ALSRCINT
ALS recovery interval. The range is 60 to 300 seconds. Integer
ALSRCPW
ALS recovery pulse width. The range is 2.0 to 100.00 seconds, in increments of 100 ms. Float
11.9 ED-APC
Edit Amplification Power Control
Usage Guidelines
Cisco ONS 15454
This command is used to modify the APC application attributes. The default value for an optional parameter is the NE default value. The value might not be the current value for the parameter. Use a RTRV-xx command to retrieve the current value.
DWDM
Provisioning
Related Commands
ED-APC:[<TID>]::<CTAG>[:::APCENABLE=<APCENABLE>];
ED-APC:PENNGROVE::CTAG:::APCENABLE=N;
11.10 ED-BITS
Edit Building Integrated Timing Supply
Usage Guidelines
Cisco ONS 15454, 15327, 15600, 15310
This command edits the BITS reference attributes.
SYNC-BITS1 and SYNC-BITS2 AIDs can be used to set the BITS-OUT port state. For a BITS facility, 64 k and 6 MHz are only applicable to ON. SSM selectable (ADMSSM) is not applicable to ONS 15600.
The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.
Synchronization
Provisioning
Related Commands
ED-NE-SYNCN
ED-SYNCN
OPR-SYNCNSW
REPT ALM BITS
REPT ALM SYNCN
REPT EVT BITS
REPT EVT SYNCN
RLS-SYNCNSW
RTRV-ALM-BITS
RTRV-ALM-SYNCN
RTRV-BITS
RTRV-COND-BITS
RTRV-COND-SYNCN
RTRV-NE-SYNCN
RTRV-SYNCN
ED-BITS:[<TID>]:<AID>:<CTAG>:::[LINECDE=<LINECDE>],[FMT=<FMT>],[LBO=<LBO>],
[SYNCMSG=<SYNCMSG>],[AISTHRSHLD=<AISTHRSHLD>],[SABIT=<SABIT>],
[BITSFAC=<BITSFAC>],[ADMSSM=<ADMSSM>][:<PST>];ED-BITS:SONOMA:BITS-2:779:::LINECDE=AMI,FMT=ESF,LBO=0-133,SYNCMSG=N,
AISTHRSHLD=PRS,SABIT=BYTE-5,IMPEDANCE=120-OHM,BITSFAC=T1,ADMSSM=PRS:IS;
Table 11-10 ED-BITS Input Parameters
AID
Access identifier from the "25.1.5 BITS" section on page 25-13
LINECDE
Line code
Parameter type is LINE_CODE—line code
•
Line code value is AMI
•
Line code value is B8ZS (bipolar with three-zero substitution)
FMT
Digital signal frame format
Parameter type is FRAME_FORMAT—frame format for a T1 port
•
Frame format is D4
•
Frame format is ESF
•
Frame format is unframed
LBO
Line build out settings. BITS line build out. Default value is 0 to 133. Integer
Parameter type is BITS_LineBuildOut—BITS line buildout
•
BITS line buildout range is 0-133
•
BITS line buildout range is 134-266
•
BITS line buildout range is 267-399
•
BITS line buildout range is 400-533
•
BITS line buildout range is 534-655
SYNCMSG
Indicates if the BITS facility supports synchronization status message. Default is on (Y)
Parameter type is EXT_RING—indicates if the ring supports the extended K1/K2/K3 protocol
•
The ring does not support the extended K1/K2/K3 protocol
•
The ring does support the extended K1/K2/K3 protocol
AISTHRSHLD
Alarm indication signal threshold
Parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL—clock source quality level for SONET
•
Do Not Use For Synchronization
•
Primary Reference Source, Stratum 1 Traceable
•
Reserved For Network Synchronization Use
•
SONET Minimum Clock Traceable
•
Stratum 2 Traceable
•
Stratum 3 Traceable
•
Stratum 3E Traceable
•
Stratum 4 Traceable
•
Synchronized, Traceability Unknown
•
Transit Node Clock (2nd Generation Only)
SABIT
When the frame format selection is E1, SABIT is the bit used to receive and transmit the SSM
Parameter type is SABITS—SA BITS
•
SABIT is BYTE-4
•
SABIT is BYTE-5
•
SABIT is BYTE-6
•
SABIT is BYTE-7
•
SABIT is BYTE-8
IMPEDANCE
When the frame format selection is E1, IMPEDANCE is the terminal impedance of the BITS-IN port
Parameter type is IMPEDANCE—the terminal impedance of the BITS-IN port
•
Impedance of 120 ohm
•
Impedance of 75 ohm
BITSFAC
BITS facility settings. BITS-2 always inherits the value of BITS-1
Parameter type is BITS_FAC—BITS facility rate. 64 k and 6 MHz are only applicable to the ONS 15454
•
2 MHz rate
•
64 K rate
•
6 MHz rate
•
E1 rate
•
T1 rate
ADMSSM
SSM selectable. Only applicable to BITS-IN when SSM is disabled.
Note
Parameter type is SYNC_CLOCK_REF_QUALITY_LEVEL—clock source quality level for SONET
•
Do Not Use For Synchronization
•
Primary Reference Source, Stratum 1 Traceable
•
Reserved For Network Synchronization Use
•
SONET Minimum Clock Traceable
•
Stratum 2 Traceable
•
Stratum 3 Traceable
•
Stratum 3E Traceable
•
Stratum 4 Traceable
•
Synchronized, Traceability Unknown
•
Transit Node Clock (2nd Generation Only)
PST
Primary state
Parameter type is PST—indicates the current overall service condition of an entity
•
In service
•
Out of service
11.11 ED-BULKROLL-<OCN_TYPE>
Edit Bulkroll (OC12, OC192, OC3, OC48)
Usage Guidelines
Cisco ONS 15454, ONS 15327, ONS 15600
This command edits information about rolling of traffic from one end point to another without interrupting service. This command uses the FORCE option to force a valid signal. The only parameters that can be edited are RMODE and FORCE. The time slots cannot be edited. Use ED-ROLL-<MOD_PATH> for single path level rolling.
See Table 27-1 on page 27-1 for supported modifiers by platform.
Bridge and Roll
Provisioning
Related Commands
ED-BULKROLL-<OCN_TYPE>:[<TID>]:<FROM>:<CTAG>:::
[RFROMSTART=<RFROMSTART>],[RFROMEND=<RFROMEND>],[CMDMDE=<CMDMDE>];ED-BULKROLL-OC48:CISCO:FAC-1-1:1:::RFROMSTART=STS-1-1-1,
RFROMEND=STS-1-1-11,CMDMDE=FRCD;
Table 11-11 ED-BULKROLL-<OCN_TYPE> Input Parameters
FROM
One of the end points. Access identifier from the "25.1.14 FACILITY" section on page 25-28 for line level rolling and bulk rolling
RFROMSTART
The starting time slot in the source roll port. For bulk rolling only. The AID is from the "25.1.10 CrossConnectId1" section on page 25-20 (except VCM and FACILITY). Defaults to STS-<FROMSLOT>-<FROMPORT>-1, where <FROMSLOT> and <FROMPORT> are the slot and port of the <FROM> AID.
RFROMEND
The ending time slot in the source roll port. For bulk rolling only. The AID is from the "25.1.10 CrossConnectId1" section on page 25-20 (except VCM and FACILITY). Defaults to STS-<FROMSLOT>-<FROMPORT>-N, where <FROMSLOT> and <FROMPORT> are the slot and port of the <FROM> AID and N is the value of OCn. (for example, OC48, n=48)
CMDMDE
Command execution mode. Defaults to NORM
Parameter type is CMDMDE—forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied
•
Force the system to override a state where the command would normally be denied
•
Execute the command normally. Do not override any conditions that might make the command fail
11.12 ED-CMD-SECU
Edit Command Security
Usage Guidelines
Cisco ONS 15454, 15327, 15600, 15310
This command edits the command security level of a particular command.
Security
Superuser
Related Commands
ED-CMD-SECU:[<TID>]:<AID>:<CTAG>::<CAP>;
ED-CMD-SECU::INIT-REG:1::SUPER;
11.13 ED-CRS-<PATH>
Edit Cross-Connect (STS1, STS12C, STS18C, STS192C, STS24C, STS36C, STS3C, STS48C, STS6C, STS9C, VT1, VT2)
Usage Guidelines
Cisco ONS 15454, 15327, 15600, 15310
See Table 27-1 on page 27-1 for supported modifiers by platform.
This command edits a cross-connection.
Note
•
•
•
•
Category
Cross Connections
Security
Provisioning
Input Format
ED-CRS-<PATH>:[<TID>]:<SRC>,<DST>:<CTAG>::[<CCT>]:[ADD=<ADD>],
[REMOVE=<REMOVE>],[CKTID=<CKTID>],[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];Input Example
ED-CRS-STS3C::STS-1-1-1,STS-2-1-1:1:::ADD=STS-13-1-1,REMOVE=STS-2-1-1,CKTID=CKTID
CMDMDE=FRCD:IS,AINS;Input Parameters
<SRC>
Source AID from the "25.1.10 CrossConnectId1" section on page 25-20.
<DST>
Destination AID from the "25.1.10 CrossConnectId1" section on page 25-20.
<CCT>
Cross-connection. The parameter type is CCT which indicates the type of cross-connection to be created.
•
A unidirectional connection from a source tributary to a destination tributary
•
Path Protection multicast drop (one-way continue)
•
Path Protection multicast end node (one-way continue)
•
A bidirectional connection between the two tributaries
Note
•
A unidirectional connection from a source tributary to a destination tributary on the protection path/fiber
•
A bidirectional connection between the two tributaries
•
A bidirectional drop and continue connection applicable only to path protection traditional and integrated DRIs
•
A bidirectional connection between the two tributaries on the extra protection path/fiber
•
Diagnostics cross-connect. Supports BERT (BLSR PCA diagnostics cross-connect).
<ADD>
AID from the "25.1.2 AidUnionId" section on page 25-9.
<REMOVE>
AID from the "25.1.2 AidUnionId" section on page 25-9.
<CKTID>
Cross-connect ID. The default is Blank or None. String of ASCII characters. Maximum length is 48. If CKTID is empty or null, the CKTID field will not be displayed.
<CMDMDE>
The parameter type is command mode (CMDMDE). Normal (NORM) mode is the default behavior for all commands but you can specify forced (FRCD) mode to force the system to override a state where the command would normally be denied. The FRCD mode of operation is applicable to delete a virtual concatenated (VCAT) member cross-connect in IS-NR or OOS-AU,AINS service states.
•
Force the system to override a state where the command would normally be denied.
•
Execute the command normally. Do not override any conditions that might make the command fail.
<PST>
Primary state. The parameter type is PST, which indicates the current overall service condition of an entity.
•
In service
•
Out of service
<SST>
Secondary state. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.14 ED-DAT
Edit Date and Time
Usage Guidelines
Cisco ONS 15454, 15327, 15600, 15310
This command edits the date and the time
System
Provisioning
Related Commands
ED-DAT:[<TID>]::<CTAG>::[<DATE>],[<TIME>];
ED-DAT:CISCO::1234::99-12-21,14-35-15;
Table 11-13 ED-DAT Input Parameters
DATE
Date. String
TIME
Time. String
11.15 ED-DS1
Edit DS1
Usage Guidelines
Cisco ONS 15454
This command edits the test access attribute for DS1 access on a DS3XM card.
Note
•
•
•
•
•
–
–
–
•
Ports
Provisioning
Related Commands
ED-DS1:[<TID>]:<AID>:<CTAG>:::[TACC=<TACC>],[TAPTYPE=<TAPTYPE>],
[MODE=<MODE>],[FMT=<FMT>];ED-DS1:PETALUMA:DS1-2-1-6-12:123:::TACC=8,TAPTYPE=DUAL,MODE=FDL,FMT=ESF;
Table 11-14 ED-DS1 Input Parameters
AID
Access identifier from the "25.1.11 DS1" section on page 25-26
TACC
TAP number within a range of 0 to 999. Indicates whether the digroup being provisioned is to be used as a test access digroup. When TACC is 0 (zero), the TAP is deleted. Integer
TAPTYPE
TAP type
Parameter type is TAPTYPE—test access point type
•
Dual FAD
•
Single FAD
MODE
Mode with which the command is to be implemented. DS1 path mode of the DS3XM-12 card. Defaults to FDL
Parameter type is DS1MODE—the DS1 path mode of the DS3XM-12 card
•
The DS1 path of the DS3XM-12 card is in AT&T 54016 mode
•
The DS1 path of the DS3XM-12 card is in FDL T1-403 mode
FMT
Digital signal format. The DS1 path frame format of the DS3XM-12 card. Defaults to UNFRAMED
Parameter type is FRAME_FORMAT—frame format for a T1 port
•
Frame format is D4
•
Frame format is ESF
•
Frame format is unframed
11.16 ED-EC1
Edit Electrical Carrier
Usage Guidelines
Cisco ONS 15454, ONS 15310-CL
This command edits the attributes of an EC1.
Note
Ports
Provisioning
Related Commands
ED-EC1:[<TID>]:<AID>:<CTAG>:::[PJMON=<PJMON>],[LBO=<LBO>],[SOAK=<SOAK>],
[SFBER=<SFBER>],[SDBER=<SDBER>],[NAME=<NAME>],[EXPTRC=<EXPTRC>],
[TRC=<TRC>],[TRCMODE=<TRCMODE>],[<TRCFORMAT>],[AISONLPBK=<AISONLPBK>],
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];ED-EC1:CISCO:FAC-1-1:123:::PJMON=0,LBO=0-225,SOAK=10,SFBER=1E-4,SDBER=1E-6,
NAME="EC1 PORT",EXPTRC="AAA",TRC="AAA",TRCMODE=MAN,TRCFORMAT="16-BYTE,
AISONLPBK=AIS_ON_LPBK_ALL,CMDMDE=CMDMDE:IS,AINS;
Table 11-15 ED-EC1 Input Parameters
AID
Access identifier from the "25.1.14 FACILITY" section on page 25-28
PJMON
A SONET pointer number (0 or 1) of an EC1 port. Integer. Defaults to 0
LBO
Line build out settings. Integer. Defaults to 0-225
Parameter type is E_LBO—electrical signal line buildout
•
Electrical signal line buildout range is 0-225
•
Electrical signal line buildout range is 226-450
SOAK
IS-AINS to IS transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). Integer. Defaults to 32
SFBER
Signal failure threshold. Defaults to 1E-4
Parameter type is SF_BER—the threshold for declaring signal failure on a facility or path
•
SFBER is 1E-3
•
SFBER is 1E-4
•
SFBER is 1E-5
SDBER
Signal degrade threshold. Defaults to 1E-7
Parameter type is SD_BER—the threshold for declaring signal degrade on a facility or path
•
SDBER is 1E-5
•
SDBER is 1E-6
•
SDBER is 1E-7
•
SDBER is 1E-8
•
SDBER is 1E-9
NAME
String. Default value is NULL. Maximum length is 32 characters
EXPTRC
String
TRC
String
TRCMODE
Trace mode
Parameter type is TRCMODE—trace mode
•
Use the previously received path trace string as the expected string. Not applicable to MXP/TXP cards
•
Use the previously received path trace string as the expected string and do not turn on AIS and RDI if TIMP is detected
•
Use the provisioned expected string as the expected string
•
Use the provisioned expected string as the expected string and do not turn on AIS and RDI if TIMP is detected
•
Turn off path trace capability. Nothing will be reported
TRCFORMAT
Trace message size
Parameter type is TRCFORMAT—trace format
•
1 byte trace message
•
16 byte trace message
•
64 byte trace message
•
Enable an attribute
AISONLPBK
Defaults to AIS_ONLPBK_FACILITY
Parameter type is AIS_ON_LPBK—Indicates if AIS is sent on a loopback
•
AIS is sent on facility loopbacks
•
AIS is sent on all loopbacks
•
AIS is not sent on loopbacks
•
AIS is sent on terminal loopbacks
CMDMDE
Command Mode. Defaults to NORM
Parameter type is CMDMDE—forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied
•
Force the system to override a state where the command would normally be denied
•
Execute the command normally. Do not override any conditions that might make the command fail
PST
Primary state. Defaults to IS
Parameter type is PST—indicates the current overall service condition of an entity
•
In service
•
Out of service
SST
Secondary state. Defaults to AINS
Parameter type is SST—provides additional information pertaining to PST and PSTQ
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.17 ED-EQPT
Edit Equipment
Usage Guidelines
Cisco ONS 15454, 15327, 15600, 15310
This command edits the attributes for a given equipment slot in the NE. If the card is in an equipment slot, this command is allowed only on the working AID.
Note
The PROTID parameter indicates the unique identifier of the protection group (the protect card). "NULL" is a special value of the PROTID parameter and indicates absence of a protection group. For the 1:1 protection type, RVRTV and RVTM parameters can be changed. For the 1:1 protection type, if the PROTID parameter is entered as "NULL", the protection group is deleted.
ED-EQPT:[<TID>]:SLOT-2:<CTAG>:::PROTID=NULL;
For the 1:N protection type, if the PROTID is "NULL", the AIDs in the list are removed from the protection group. If all the working cards are in the AID list, the protection group is deleted.
Example: if Slot-1, Slot-2 and Slot-4 were the only working cards in the protection group. The following command will remove Slot-4 from the protection group:
ED-EQPT:[<TID>]:SLOT-4:<CTAG>:::PROTID=NULL;
The protection group still has Slot-1 and Slot-2 as working cards.
The following command will remove all the other working cards in the above example and consequently, delete the protection group itself:
ED-EQPT:[<TID>]:SLOT-2&SLOT-1:<CTAG>:::PROTID=NULL;
The ED-EQPT command can be successfully executed on an already provisioned card to add or remove a working card from a protection group. This command is not valid on a protect card. Only cards can be added to or removed from a protection group. Protection type is immutable and is determined at the time of creation of a protection group (while adding the first working card). Once provisioned, the equipment type cannot be edited either.
Examples of adding an existing card to a protection group using the ED-EQPT command:
1:1 protection group
ED-EQPT::SLOT-2:12:::PROTID=SLOT-1,RVRTV=Y,RVTM=9.0;
1:N protection group
ED-EQPT::SLOT-2:12:::PROTID=SLOT-3,PRTYPE=1-N,RVTM=6.5;
Error conditions for editing a 1:1 or 1:N protection group might be:
1.
2.
3.
4.
5.
a.
The DS3XM-12 card in the lower speed I/O slot with the XCVT/XC10G card only allows the DS3XM-12-STS12 CARDMODE. Other cases allow the CARDMODE to be DS3XM-12-STS-48
b.
c.
6.
7.
Note
Equipment
Provisioning
Related Commands
ED-EQPT:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>],[PRTYPE=<PRTYPE>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[CMDMDE=<CMDMDE>],
[CARDMODE=<CARDMODE>],[PEERID=<PEERID>],[REGENNAME=<REGENNAME>],
[PWL=<PWL>],[RETIME=<RETIME>]:[<PST>[,<SST>]];ED-EQPT:CISCO:SLOT-2:123:::PROTID=SLOT-1,PRTYPE=1-1,RVRTV=Y,RVTM=9.0,
CMDMDE=FRCD,CARDMODE=DS3XM12-STS48,PEERID=SLOT-2,
REGENNAME="THIS GROUP",PWL=1530.33,RETIME=Y:OOS,MT;
Table 11-16 ED-EQPT Input Parameters
AID
Access identifier from the "25.1.13 EQPT" section on page 25-27
PROTID
Protecting card slot number of the protection group from the "25.1.20 PRSLOT" section on page 25-33
PRTYPE
Protection group type
Parameter type is PROTECTION_GROUP—protection group type
•
1 for 1 protection group
•
1 for N protection group
RVRTV
Revertive mode. The value Y indicates that the protection switching system reverts service to the original line after restoration. The value N indicates that the protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
RVTM
Revertive time
Parameter type is REVERTIVE_TIME—revertive time
•
Revertive time is 0.5 to 12.0 minutes
CMDMDE
Command mode. Only applicable when creating or deleting a protection group (1:1 or 1:N) and/or adding cards to an existing protection group (1:N). Default is NORM. If creating or adding cards to a protection group, specifying FRCD requires the card to be physically plugged in and in the service state (IS). If removing cards from a protection group (1:N) or deleting the protection group (1:1, 1:N), specifying FRCD requires that there are no cross-connects (services) on the card
Parameter type is CMDMDE—forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied
•
Force the system to override a state where the command would normally be denied
•
Execute the command normally. Do not override any conditions that might make the command fail
CARDMODE
Card mode
Note
TL1 will not set a default CARD_MODE value at the management interface level if no PWL value is given
Parameter type is CARDMODE—card mode. Card mode is applicable to cards that have multiple capabilities, for example, the ML card can operate in two distinct modes: Linear Mapper Mode and L2/L3 Mode
•
The DS3XM-12 card in the STS12 back plane rate mode
•
The DS3XM-12 card in the STS48 back plane rate mode
•
Line terminating mode
•
Section terminating mode
•
Transparent mode AIS
•
Transparent mode SQUELCH
•
FC_MR-4 card with distance extension support
•
FC_MR-4 card without distance extension support
•
ML-Series card in DOS FPGA using GFP framing type
•
ML-Series card in DOS FPGA using HDLC framing type
•
Fibre channel or GIGE mode for the MXP-MR-2.5G card
PEERID
The regeneration peer slot from the "25.1.13 EQPT" section on page 25-27
REGENNAME
The name of a regeneration group. String
PWL
Provisioned wavelength. TL1 will not set a default PWL value at the management level if no PWL value is given
Parameter type is OPTICAL_WLEN—optical wavelength
•
Wavelength 1
•
Wavelength 2
•
Wavelength 3
•
Wavelength 4
•
Wavelength 5
•
Wavelength 6
•
Wavelength 7
•
Wavelength 8
•
Wavelength 9
•
Wavelength 10
•
Wavelength 11
•
Wavelength 12
•
Wavelength 13
•
Wavelength 14
•
Wavelength 15
•
Wavelength 16
•
Wavelength 17
•
Wavelength 18
•
Wavelength 19
•
Wavelength 20
•
Wavelength 21
•
Wavelength 22
•
Wavelength 23
•
Wavelength 24
•
Wavelength 25
•
Wavelength 26
•
Wavelength 27
•
Wavelength 28
•
Wavelength 29
•
Wavelength 30
•
Wavelength 31
•
Wavelength 32
•
Use Tunable Wavelength 1
RETIME
Indicates if retiming is needed. Applicable only to the DS1-E1-56 card (ONS 15454)
Parameter type is YES_NO—whether the user's password is about to expire, the user is logged into the NE, or the user is locked out of the NE
•
No
•
Yes
PST
Primary state
Parameter type is PST—indicates the current overall service condition of an entity
•
In service
•
Out of service
SST
Secondary state
Parameter type is SST—provides additional information pertaining to PST and PSTQ
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.18 ED-FAC
Edit Facility
Usage Guidelines
Cisco ONS 15454, 15327, 15600, 15310
This command provisions the payload (or signal) type of facility. The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command to retrieve them.
Ports
Provisioning
Related Commands
ED-FAC:[<TID>]:<SRC>:<CTAG>:::[PAYLOAD=<PAYLOAD>],
[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];ED-FAC:CISCO:FAC-3-9:2222:::PAYLOAD=E4-FRAMED,CMDMDE=CMDMDE:IS,AINS;
Table 11-17 ED-FAC Input Parameters
SRC
Source access identifier from the "25.1.14 FACILITY" section on page 25-28
PAYLOAD
The payload for the card
Parameter type is PAYLOAD—identifies payload type
•
10 Gigabit Ethernet Fibre Channel mode
•
10 Gigabit Ethernet
•
1 Gigabit Fibre Channel mode
•
1 Gigabit FICON mode
•
2 Gigabit Fibre Channel mode
•
2 Gigabit FICON mode
•
DS3 mode
•
Video mode
•
EC1 mode
•
ESCON mode
•
ETR/CLO payload mode
•
Gigabit Ethernet Payload
•
HDTV mode
•
ISC1 Mode
•
ISC3 Mode
•
SONET OC-12 mode
•
SONET OC-3 mode
•
SONET OC-48 mode
•
Pass through mode
•
SDI-D1-Video mode
•
SONET Payload Mode
CMDMDE
Command Mode. Defaults to NORM
Parameter type is CMDMDE—forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied
•
Force the system to override a state where the command would normally be denied
•
Execute the command normally. Do not override any conditions that might make the command fail
PST
Primary state. Defaults to IS
Parameter type is PST—indicates the current overall service condition of an entity
•
In service
•
Out of service
SST
Secondary state. Defaults to AINS
Parameter type is SST—provides additional information pertaining to PST and PSTQ
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.19 ED-FFP-<MOD2DWDMPAYLOAD>
Edit Facility Protection Group (10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, D1VIDEO, DV6000, ETRCLO, GIGE, HDTV, ISC1)
Usage Guidelines
Cisco ONS 15454
This command edits a Y-cable protection group on client facilities.
DWDM
Provisioning
Related Commands
ED-FFP-<MOD2DWDMPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[PSDIRN=<PSDIRN>][:];ED-FFP-CLNT:CISCO:FAC-1-1:100:::PROTID=DC-METRO,RVRTV=N,RVTM=1.0,PSDIRN=BI;
Table 11-18 ED-FFP-<MOD2DWDMPAYLOAD> Input Parameters
AID
Access identifier from the "25.1.14 FACILITY" section on page 25-28
PROTAID
The protection group identifier (protection group name). Defaults to the protecting port AID of the protection group. PROTAID can have a maximum length of 32 characters. String
RVRTV
Revertive mode. The value Y indicates that the protection switching system reverts service to the original line after restoration. The value N indicates that the protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N. Only applies to path protection
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
RVTM
Revertive time. RVTM is not allowed to be set while "RVRTV" is N. Only applies to path protection
Parameter type is REVERTIVE_TIME—revertive time
•
Revertive time is 0.5 to 12.0 minutes
PSDIRN
Protection switch operation. Identifies the switching mode. Defaults to UNI.
Note
Parameter type is UNI_BI—unidirectional switch operations
•
Bidirectional protection switching
•
Unidirectional protection switching
11.20 ED-FFP-<OCN_TYPE>
Edit Facility Protection Group (OC3, OC12, OC48, OC192)
Usage Guidelines
Cisco ONS 15454, 15327, 15600, 15310
See Table 27-1 on page 27-1 for supported modifiers by platform.
This command edits the optical facility protection.
Note
•
•
Protection
Provisioning
Related Commands
ED-FFP-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>],
[RVRTV=<RVRTV>],[RVTM=<RVTM>],[PSDIRN=<PSDIRN>],[VRGRDTM=<VRGRDTM>],
[DTGRDTM=<DTGRDTM>],[RCGRDTM=<RCGRDTM>][:];ED-FFP-OC3:PETALUMA:FAC-1-1:1:::PROTID=PROT_NAME,RVRTV=Y,RVTM=1.0,
PSDIRN=BI,VRGRDTM=0.5,DTGRDTM=1.0,RCGRDTM=1.0;
Table 11-19 ED-FFP-<OCN_TYPE> Input Parameters
AID
Access identifier from the "25.1.14 FACILITY" section on page 25-28
PROTAID
The protection group identifier (protection group name). PROTAID can have a maximum length of 32 characters. String
RVRTV
Revertive mode. The value Y indicates that the protection switching system reverts service to the original line after restoration. The value N indicates that the protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
RVTM
Revertive time
Parameter type is REVERTIVE_TIME—revertive time
•
Revertive time is 0.5 to 12.0 minutes
PSDIRN
Protection switch operation. Indicates the switch mode. Defaults to UNI
Parameter type is UNI_BI—unidirectional and bidirectional switch operations
•
Bidirectional protection switching
•
Unidirectional protection switching
VRGRDTM
Verification guard timer. Only applicable to optimized 1+1
Parameter type is VERIFICATION_GUARD_TIMER—optimized 1+1 verification guard timer
•
500 ms
•
1 second
DTGRDTM
Detection guard timer. Only applicable to optimized 1+1
Parameter type is DETECTION _GUARD_TIMER—optimized 1+1 detection guard timer
•
0 seconds
•
50 ms
•
100 ms
•
500 ms
•
1 second to 5 seconds
RCGRDTM
Recovery guard timer. Only applicable to optimized 1+1
Parameter type is RECOVERY_GUARD_TIMER—optimized 1+1 recovery guard timer
•
0 seconds
•
50 ms
•
100 ms
•
500 ms
•
1 second to 10 seconds
11.21 ED-FFP-OCH
Edit Facility Protection Group Optical Channel
Usage Guidelines
Cisco ONS 15454
This command changes the provisioning for the default protection group on the DWDM port of a TXP_MR_2.5G and TXPP_MR_2.5G card.
DWDM
Provisioning
Related Commands
ED-FFP-OCH:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>],[RVRTV=<RVRTV>],
[RVTM=<RVTM>],[PSDIRN=<PSDIRN>][:];ED-FFP-OCH:VA454-22:CHAN-2-2:100:::PROTID="FIXEDPROTECTION",RVRTV=N,
RVTM=1.0,PSDIRN=BI;
Table 11-20 ED-FFP-OCH Input Parameters
AID
Access identifier from the "25.1.7 CHANNEL" section on page 25-14
PROTAID
The protection group identifier (protection group name). String
RVRTV
Revertive mode. The value Y indicates that the protection switching system reverts service to the original line after restoration. The value N indicates that the protection switching system does not revert service to the original line after restoration. RVRTV is applicable only for 1+1 protection switching. Null defaults to N
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
RVTM
Revertive time
Parameter type is REVERTIVE_TIME—revertive time
•
Revertive time is 0.5 to 12.0 minutes
PSDIRN
Protection switch operation
Parameter type is TRANS_MODE—G1000 transponder mode
•
Bidirectional
•
Not in transponder mode
•
Unidirectional
11.22 ED-FSTE
Edit Fast Ethernet
Usage Guidelines
Cisco ONS 15454, ONS 15310-CL
This command edits the front end port information of the fast (10/100 Mbps) Ethernet card.
The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command to retrieve them.
Note
Ports
Provisioning
Related Commands
ED-FSTE:[<TID>]:<AID>:<CTAG>:::[FLOW=<FLOW>],[EXPDUPLEX=<EXPDUPLEX>],
[EXPSPEED=<EXPSPEED>],[VLANCOS=<VLANCOS>],[IPTOS=<IPTOS>],
[NAME=<NAME>],[CMDMDE=<CMDMDE>],[SOAK=<SOAK>]:[<PST>[,<SST>]];ED-FSTE:CISCO:FAC-1-1:123:::FLOW=FLOW,EXPDUPLEX=EXPDUPLEX,
EXPSPEED=EXPSPEED, VLANCOS=VLANCOS,IPTOS=IPTOS,
NAME="FSTE PORT",CMDMDE=CMDMDE,SOAK=32:IS,AINS;
Table 11-21 ED-FSTE Input Parameters
AID
Access identifier from the "25.1.14 FACILITY" section on page 25-28
FLOW
Flow control
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
EXPDUPLEX
Ethernet duplex mode
Parameter type is ETHER_DUPLEX—duplex mode
•
Auto mode
•
Full mode
•
Half mode
EXPSPEED
Ethernet speed
Parameter type is ETHER_SPEED—Ethernet speed
•
100 Mbps
•
10 Gbps
•
10 Mbps
•
1 Gbps
•
Auto
VLANCOS
Priority queuing threshold based on VLAN class of service of incoming Ethernet packets. Default value is 1175. Integer
IPTOS
Priority queuing threshold based on IP type of service of incoming Ethernet packets. Default value is 368. Integer
NAME
Name. String
CMDMDE
Command Mode. The FRCD mode of operation is applicable to delete a VCAT member cross-connect from IS-NR or OOS-AU,AINS service state
Parameter type is CMDMDE—forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied
•
Force the system to override a state where the command would normally be denied
•
Execute the command normally. Do not override any conditions that might make the command fail
SOAK
OOS-AINS to IS transition soak time as measured in 15 minute intervals, so a value of 4 translates to a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). Integer
PST
Primary state
Parameter type is PST—indicates the current overall service condition of an entity
•
In service
•
Out of service
SST
Secondary state
Parameter type is SST—provides additional information pertaining to PST and PSTQ
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.23 ED-G1000
Edit G1000
Usage Guidelines
Cisco ONS 15454
This command edits the attributes related to a G1000 port.
The default values for all optional parameters are NE default values. These values might not be the current value for a parameter. In order to obtain the current value, issue the RTRV-XX command.
Ports
Provisioning
Related Commands
ED-G1000:[<TID>]:<AID>:<CTAG>:::[MFS=<MFS>],[FLOW=<FLOW>],
[LOWMRK=<LOWMRK>],[HIWMRK=<HIWMRK>],[AUTONEG=<AUTONEG>],
[NAME=<NAME>],[CMDMDE=<CMDMDE>],[SOAK=<SOAK>]:[<PST>[,<SST>]];ED-G1000:TID:FAC-1-1:CTAG:::MFS=1548,FLOW=Y,LOWMRK=20,HIWMRK=492,
AUTONEG=Y,NAME="G1000 PORT",CMDMDE=FRCD,SOAK=32:OOS,DSBLD;
Table 11-22 ED-G1000 Input Parameters
AID
Access identifier from the "25.1.14 FACILITY" section on page 25-28
MFS
Maximum frame size
Parameter type is MFS_TYPE—maximum frame size used by an Ethernet card
•
Normal frame size
•
Jumbo frame size
FLOW
Flow control
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
LOWMRK
Low watermark value. Integer. Defaults to 25. LOWMRK is available starting with Release 4.0.1
HIWMRK
High watermark value. Integer. Defaults to 485
AUTONEG
Automatic negotiation. Defaults to Y
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
NAME
Name. String. Default is NULL. Maximum length is 32 characters
CMDMDE
Command execution mode
Parameter type is CMDMDE—forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied
•
Force the system to override a state where the command would normally be denied
•
Execute the command normally. Do not override any conditions that might make the command fail
SOAK
OOS-AINS to IS transition soak time as measured in 15-minute intervals. A value of 4 equals a soak time of 1 hour. The allowable range is 0 to 192 intervals (maximum of 48 hours). Integer. Defaults to 32
ENCAP
Encapsulation. String
PST
Primary state. Defaults to OOS
Parameter type is PST—indicates the current overall service condition of an entity
•
In service
•
Out of service
SST
Secondary state. Defaults to DSBLD
Parameter type is SST—provides additional information pertaining to PST and PSTQ
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.24 ED-GFP
Edit Generic Framing Protocol
Usage Guidelines
Cisco ONS 15454, ONS 15310-CL, ONS 15600
This command applies to the ONS 15454 CE-100T-8 card, the ONS 15454 FC_MR-4 card, the ONS 15310-CL CE-100T-8 card and the ONS 15600 ASAP card.
Note
•
•
Ports
Provisioning
Related Commands
ED-GFP:[<TID>]:<AID>:<CTAG>:::[FCS=<FCS>],[AUTOTHGFPBUF=<AUTOTHGFPBUF>],
[GFPBUF=<GFPBUF>],[FILTER=<FILTER>];ED-GFP:CISCO:VFAC-1-0:123:::FCS=N,AUTOTHGFPBUF=Y,GFPBUF=16,FILTER=EGRESS;
Table 11-23 ED-GFP Input Parameters
AID
Access identifier from the "25.1.14 FACILITY" section on page 25-28.
Note
FCS
Payload frame check sequence
Parameter type is FCS—frame check sequence
•
Frame check sequencing using 16 bits
•
Frame check sequencing using 32 bits
•
No frame check sequence
AUTOTHGFPBUF
Parameter type is ON_OFF—disable or enable an attribute
•
Disable an attribute
•
Enable an attribute
FILTER
Parameter type is GFP_FILTER—filter feature in GFP
•
Activate filter feature on egress port
•
Turn off filter feature
11.25 ED-HDLC
Edit High-Level Data Link Control
Usage Guidelines
Cisco ONS 15600
This command edits HDLC-related attributes for HDLC-encapsulated payloads.
Ports
Provisioning
Related Commands
ED-HDLC:[<TID>]:<SRC>:<CTAG>[:::FCS=<FCS>];
ED-HDLC:TID:VFAC-SLOT-PORT:CTAG:::FCS=FCS-16;
Table 11-24 ED-HDLC Input Parameters
SRC
Access identifier from the "25.1.14 FACILITY" section on page 25-28. The ONS 15600 ASAP card uses the VFAC AID
FCS
Payload frame check sequence
Parameter type is FCS—frame check sequence
•
Frame check sequence using 16 bits
•
Frame check sequence using 32 bits
•
No frame check sequence
11.26 ED-LNK-<MOD2O>
Edit Link (OCH, OMS, OTS)
Usage Guidelines
Cisco ONS 15454
This command edits an optical link state.
DWDM
Provisioning
Related Commands
ED-LNK-<MOD2O>:[<TID>]:<FROM>,
<TO>:<CTAG>:::[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];ED-LNK-OMS:PENNGROVE:BAND-6-1-TX,BAND-13-1-RX:114:::CMDMDE=CMDMDE:IS,
AINS;
Table 11-25 ED-LNK-<MODO> Input Parameters
FROM
Identifier at one end of the optical link from the "25.1.4 BAND" section on page 25-13
TO
Identifier at the other end of the optical link from the "25.1.4 BAND" section on page 25-13
CMDMDE
Command Mode. The FRCD mode of operation is applicable to delete a VCAT member cross-connect from IS-NR or OOS-AU,AINS service state
Parameter type is CMDMDE—forces the system to execute a given command regardless of any standing conditions. Normal mode is the default behavior for all commands but you can specify FRCD to force the system to override a state where the command would normally be denied
•
Force the system to override a state where the command would normally be denied
•
Execute the command normally. Do not override any conditions that might make the command fail
PST
Primary state
Note
Parameter type is PST—indicates the current overall service condition of an entity
•
In service
•
Out of service
SST
Secondary state
Note
Parameter type is SST—provides additional information pertaining to PST and PSTQ
•
Automatic in service
•
Disabled
•
Loopback
•
Mismatch of equipment and attributes
•
Maintenance mode
•
Out of group
•
Software downloading
•
Unassigned
•
Unequipped
11.27 ED-LNKTERM
Edit Provisionable Patchcord Termination
Usage Guidelines
Cisco ONS 15454, ONS 15327, ONS 15310-CL
This command edits the attributes of a provisionable patchcord that has already been created. Only the remote end attributes (REMOTENODE, REMOTELNKTERMID) can be edited.
Note
•
•
•
Provisionable Patchcords
Provisioning
Related Commands
ED-LNKTERM:[<TID>]:<AID>:<CTAG>:::[REMOTENODE=<REMOTENODE>],
[REMOTELNKTERMID=<REMOTELNKTERMID>];ED-LNKTERM::LNKTERM-1:CTAG:::REMOTENODE=172.20.208.226,
REMOTELNKTERMID=25;
Table 11-26 ED-LNKTERM Input Parameters
AID
Access identifier from the "25.1.17 LNKTERM" section on page 25-32. Indicates a link (provisionable patchcord) termination on the local node
REMOTENODE
The node where the other end of the provisionable patchcord resides. This can be an IP address or a valid TID. Defaults to the IP address of the local node/existing value. String
REMOTELNKTERMID
The corresponding provisionable patchcord termination on the remote node (as specified by the REMOTENODE parameter). Integer value within the range of 1 to 65535. Defaults to existing value
11.28 ED-NE-GEN
Edit Network Element General
Usage Guidelines
Cisco ONS 15454, 15327, 15600, 1
