Cisco Discovery Protocol Configuration Guide Cisco IOS XE Release 3SE (5700)

Available Languages

Download Options

  • PDF     (1.2 MB)
    View with Adobe Reader on a variety of devices
Updated:July 25, 2012

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Contents

Cisco Discovery Protocol Version 2

Cisco Discovery Protocol (formerly known as CDP) is a Layer 2, media-independent, and network-independent protocol that runs on Cisco devices and enables networking applications to learn about directly connected devices nearby. This protocol facilitates the management of Cisco devices by discovering these devices, determining how they are configured, and allowing systems using different network-layer protocols to learn about each other.

This module describes Cisco Discovery Protocol Version 2 and how it functions with Simple Network Management Protocol (SNMP).

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Prerequisites for Using Cisco Discovery Protocol

  • Interfaces must support Subnetwork Access Protocol (SNAP) headers.

Restrictions for Using Cisco Discovery Protocol

  • Cisco Discovery Protocol functions only on Cisco devices.

  • Cisco Discovery Protocol is not supported on Frame Relay multipoint subinterfaces.

Information About Using Cisco Discovery Protocol

VLAN Trunking Protocol

VLAN Trunking Protocol (VTP) is a discovery technique used by switches. A switch advertises its management domain, configuration revision number, VLANs, and their specific parameters on its trunk ports. A VTP domain is made up of a single device or interconnected devices that share the same VTP domain name. A switch can belong to only one VTP domain.

Type-Length-Value Fields

Type-Length-Value (TLV) fields are blocks of information embedded in Cisco Discovery Protocol advertisements. Information in advertisements varies, and the TLV frame format allows for extending advertisements when needed. The table below summarizes the TLV definitions.

Table 1 Type-Length-Value Definitions for Cisco Discovery Protocol Version 2

TLV

Definition

Address TLV

Contains network addresses of both receiving and sending devices.

Application TLV

Provides a mechanism to send an application-specific TLV through Cisco Discovery Protocol.

Capabilities TLV

Identifies the device type, which indicates the functional capability of the device. For example, a switch.

Device-ID TLV

Identifies the device name in the form of a character string.

Full or Half Duplex TLV

Indicates the duplex configuration of the Cisco Discovery Protocol broadcast interface. This information is used by network operators to diagnose connectivity problems between adjacent network devices.

IP Network Prefix TLV

Contains a list of network prefixes to which a sending device can forward IP packets. A prefix includes the interface protocol and the port number. For example, Ethernet 1/0.

Location TLV

Delivers location-based information to endpoint devices through access devices (switches or routers) by using Cisco Discovery Protocol. The location TLV can send the following types of information:

  • Civic location information—Provides the civic address information and the postal information. Examples include street address, road name, and postal community name.

  • ELIN location information—Provides the location information of a caller. The location is determined by the emergency location identifier number (ELIN), which is a phone number that routes an emergency call to the local public safety answering point (PSAP) and which the PSAP can use to call back the emergency caller.

You must configure the location TLV on the device before Cisco Discovery Protocol can deliver location-based information to endpoint devices. For more information about configuring location TLV, see the Using Link Layer Discovery Protocol in Multivendor Networks module.

Location-Server TLV

Provides a mechanism for location servers to transfer the required information to neighboring devices.

Native VLAN TLV

Indicates, per interface, the assumed VLAN for untagged packets on the interface. Cisco Discovery Protocol learns the native VLAN for an interface.

This field is implemented only for interfaces that support the IEEE 802.1Q protocol.

Platform TLV

Identifies the hardware platform of the device. For example, Cisco 4500.

Port-ID TLV

Identifies the port on which a Cisco Discovery Protocol packet is sent.

Version TLV

Contains the device software release information.

VTP Management Domain TLV

Advertises the configured VLAN Trunking Protocol (VTP)-management-domain name of the system. This name is used by network operators to verify VTP-domain configuration in adjacent network nodes.

Cisco Discovery Protocol

Cisco Discovery Protocol is a Layer 2, media-independent, and network-independent protocol that networking applications use to learn about nearby, directly connected devices. Cisco Discovery Protocol is enabled by default. Each device configured for Cisco Discovery Protocol advertises at least one address at which the device can receive messages and sends periodic advertisements (messages) to the well-known multicast address 01:00:0C:CC:CC:CC. Devices discover each other by listening at that address. They also listen to messages to learn when interfaces on other devices are up or go down.

Advertisements contain time-to-live information, which indicates the length of time a receiving device should hold Cisco Discovery Protocol information before discarding it. Advertisements supported and configured in Cisco software are sent, by default, every 60 seconds on interfaces that support Subnetwork Access Protocol (SNAP) headers. Cisco devices never forward Cisco Discovery Protocol packets. Cisco devices that support Cisco Discovery Protocol store the information received in a table. Information in this table is refreshed every time an advertisement is received, and information about a device is discarded after three advertisements from that device are missed.

The information contained in Cisco Discovery Protocol advertisements varies based on the type of device and the installed version of the operating system. Some of the information that Cisco Discovery Protocol can learn includes:

  • Cisco IOS version running on Cisco devices

  • Hardware platform of devices

  • IP addresses of interfaces on devices

  • Locally connected devices advertising Cisco Discovery Protocol

  • Interfaces active on Cisco devices, including encapsulation type

  • Hostname

  • Duplex setting

  • VLAN Trunking Protocol (VTP) domain

  • Native VLAN

Cisco Discovery Protocol Version 2 provides more intelligent, device-tracking features than those available in Version 1. One of the features available is an enhanced reporting mechanism for more rapid error tracking, which helps to reduce network downtime. Errors reported include mismatched native VLAN IDs (IEEE 802.1Q) on connected ports and mismatched port-duplex states between connected devices. Messages about reported errors can be sent to the console or to a logging server.

You can use show commands for getting detailed output on VTP management domains and duplex modes of neighboring devices, counters related to Cisco Discovery Protocol, and VLAN IDs of connecting ports.

Using Cisco Discovery Protocol with SNMP

Using Cisco Discovery Protocol with Simple Network Management Protocol (SNMP) allows network management applications to learn the type of device and the SNMP agent address of neighboring devices. Applications can also send SNMP queries to these neighboring devices.

The SNMP management application learns protocol addresses and types of neighboring devices by retrieving the Cisco Discovery Protocol tables from SNMP agents on those devices. When enabled, the network management module (NMM) SNMP agent discovers neighboring devices and builds its local cache with information about these devices. A management workstation can retrieve this cache by sending SNMP requests to access CISCO-CDP-MIB.

Cisco Discovery Protocol and On-Demand Routing Support for ATM PVCs

Cisco Discovery Protocol and On-Demand Routing (ODR) support exists for ATM point-to-point permanent virtual circuits (PVCs). ODR uses Cisco Discovery Protocol to propagate IP address information in hub-and-spoke topologies. When ODR is enabled, spoke routers automatically advertise their subnets by using Cisco Discovery Protocol.

Cisco Discovery Protocol is disabled by default on ATM PVC interfaces. To enable Cisco Discovery Protocol, use the cdp run command in global configuration mode and the cdp enable command in interface configuration mode on both ends of the PVC. To enable ODR, use the router odr command in global configuration mode on the hub router, and turn off all dynamic-routing protocols on the spoke routers. For details about configuring ODR, see the “Configuring On-Demand Routing” section in the IP Routing: ODR Configuration Guide.

Cisco Discovery Protocol Support in IPv6

Cisco Discovery Protocol in IPv6 functions in the same way as in IPv4 and offers the same benefits. The IPv6 enhancement allows Cisco Discovery Protocol to exchange IPv6 and neighbor addressing information. The enhancement also provides IPv6 information to network management products and troubleshooting tools.

Benefits of Cisco Discovery Protocol

Cisco Discovery Protocol provides the following benefits:

  • Allows systems using different network layer protocols to learn about one another.

  • Facilitates management of Cisco devices by discovering them and discovering how they are configured.

  • Assists with troubleshooting Type-Length-Value Fields (TLV) fields.

  • Works with SNMP by learning SNMP agent addresses and sending SNMP queries.

How to Use Cisco Discovery Protocol Version 2

Disabling and Enabling Cisco Discovery Protocol on a Cisco Device

Disabling Cisco Discovery Protocol on a Supported Device

Procedure
     Command or ActionPurpose
    Step 1 enable


    Example:
    Device> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.

     
    Step 2 configure terminal


    Example:
    Device# configure terminal
     

    Enters global configuration mode.

     
    Step 3 no cdp run


    Example:
    Device(config)# no cdp run
     

    Disables Cisco Discovery Protocol on a supported device.

     
    Step 4 end


    Example:
    Device(config)# end
     

    Returns the CLI to privileged EXEC mode.

     

    Enabling Cisco Discovery Protocol on a Supported Device

    Procedure
       Command or ActionPurpose
      Step 1 enable


      Example:
      Device> enable
       

      Enables privileged EXEC mode.

      • Enter your password if prompted.

       
      Step 2 configure terminal


      Example:
      Device# configure terminal
       

      Enters global configuration mode.

       
      Step 3 cdp run


      Example:
      Device(config)# cdp run
       

      Enables Cisco Discovery Protocol on a supported device.

       
      Step 4 end


      Example:
      Device(config)# end
       

      Exits configuration mode and returns to privileged EXEC mode.

       

      Disabling and Enabling Cisco Discovery Protocol on a Supported Interface

      Disabling Cisco Discovery Protocol on a Supported Interface

      If the encapsulation of an interface is changed, Cisco Discovery Protocol is reenabled on that interface even if Cisco Discovery Protocol was previously disabled. For example, when interface encapsulation changes from PPP to High-Level Data Link Control (HDLC), Cisco Discovery Protocol is reenabled on that interface even though it was explicitly disabled with the no cdp run command on that interface. This behavior is by design. The encapsulation changes the Layer 2 protocol configured for that interface and resets the interface configuration to the default Cisco Discovery Protocol state of being enabled, assuming that Cisco Discovery Protocol is enabled globally on the device.

      Procedure
         Command or ActionPurpose
        Step 1 enable


        Example: 
        Device> enable
         

        Enables privileged EXEC mode.

        • Enter your password if prompted.

         
        Step 2 configure terminal


        Example: 
        Device# configure terminal
         

        Enters global configuration mode.

         
        Step 3 interface type number [name-tag]


        Example: 
        Device(config)# interface Gigabitethernet 1/0/1
         

        Configures the specified interface and enters interface configuration mode.

         
        Step 4 no cdp enable


        Example: 
        Device(config-if)# no cdp enable
         

        Disables Cisco Discovery Protocol on the interface.

        Note   

        If the encapsulation of an interface is changed, Cisco Discovery Protocol is reenabled on that interface even if Cisco Discovery Protocol was previously disabled.

         
        Step 5 end


        Example: 
        Device(config-if)# end
         

        Exits to privileged EXEC mode.

         
        Example

        In the following example, Cisco Discovery Protocol is first disabled on an interface: 

        Device(config)#  interface Gigabitethernet 1/0/1
Device(config-if)# no ip address

Device(config-if)# shutdown
Device(config-if)# no cdp enable 
! Cisco Discovery Protocol is disabled.
Device(config-if)# end

        Enabling Cisco Discovery Protocol on a Supported Interface


        Note

        If the encapsulation of an interface is changed, Cisco Discovery Protocol is reenabled on that interface, even if Cisco Discovery Protocol was previously disabled.

        Procedure
           Command or ActionPurpose
          Step 1 enable


          Example: 
          Device> enable
           

          Enables privileged EXEC mode.

          • Enter your password if prompted.

           
          Step 2 configure terminal


          Example: 
          Device# configure terminal
           

          Enters global configuration mode.

           
          Step 3 interface type number [name-tag]


          Example: 
          Device(config)# interface Gigabitethernet 1/0/1
           

          Configures the specified interface and places the CLI in interface configuration mode.

          Note   

          If the encapsulation of an interface is changed, Cisco Discovery Protocol is reenabled on that interface, even if Cisco Discovery Protocol was previously disabled.

           
          Step 4 cdp enable


          Example: 
          Device(config-if)# cdp enable
           

          Enables Cisco Discovery Protocol on the interface.

           
          Step 5 end


          Example: 
          Device(config-if)# end
           

          Returns the CLI to privileged EXEC mode.

           

          Setting the Transmission Timer and Hold Time

          Perform this task to set the frequency of Cisco Discovery Protocol transmissions and the hold time for Cisco Discovery Protocol packets.

          Procedure
             Command or ActionPurpose
            Step 1 enable


            Example:
            Device> enable
             

            Enables privileged EXEC mode.

            • Enter your password if prompted.

             
            Step 2 configure terminal


            Example:
            Device# configure terminal
             

            Enters global configuration mode.

             
            Step 3 cdp timer seconds


            Example:
            Device(config)# cdp timer 30
             

            Specifies the frequency of transmission of Cisco Discovery Protocol packets.

             
            Step 4 cdp holdtime seconds


            Example:
            Device(config)# cdp holdtime 90
             

            Specifies the time for which a receiving device should hold information before discarding it.

             
            Step 5 end


            Example:
            Device(config)# end
             

            Enters privileged EXEC mode.

             

            Disabling and Reenabling Cisco Discovery Protocol Version 2 Advertisements

            The broadcasting of Cisco Discovery Protocol Version 2 advertisements is enabled by default on Cisco devices. To disable or reenable this broadcasting, perform these tasks.

            Disabling Cisco Discovery Protocol Version 2 Advertisements

            Procedure
               Command or ActionPurpose
              Step 1 enable


              Example:
              Device> enable
               

              Enables privileged EXEC mode.

              • Enter your password if prompted.

               
              Step 2 configure terminal


              Example:
              Device# configure terminal
               

              Enters global configuration mode.

               
              Step 3 no cdp advertise-v2


              Example:
              Device(config)# no cdp advertise-v2
               

              Disables the broadcasting of Cisco Discovery Protocol Version 2 advertisements.

               
              Step 4 end


              Example:
              Device(config)# end
               

              Exits to privileged EXEC mode.

               

              Enabling Cisco Discovery Protocol Version 2 Advertisements

              Procedure
                 Command or ActionPurpose
                Step 1 enable


                Example:
                Device> enable
                 

                Enables privileged EXEC mode.

                • Enter your password if prompted.

                 
                Step 2 configure terminal


                Example:
                Device# configure terminal
                 

                Enters global configuration mode.

                 
                Step 3 cdp advertise-v2


                Example:
                Device(config)# cdp advertise-v2
                 

                Enables the broadcasting of Cisco Discovery Protocol Version 2 advertisements.

                 
                Step 4 end


                Example:
                Device(config)# end
                 

                Exits to privileged EXEC mode.

                 

                Monitoring and Maintaining Cisco Discovery Protocol

                Perform this task to monitor and maintain Cisco Discovery Protocol on a device. This task and all its steps are optional, and the steps can be performed in any sequence.

                Procedure
                   Command or ActionPurpose
                  Step 1 enable


                  Example:
                  Device> enable
                   

                  Enables privileged EXEC mode.

                  • Enter your password if prompted.

                   
                  Step 2 clear cdp counters


                  Example:
                  Device# clear cdp counters
                   

                  Resets Cisco Discovery Protocol traffic counters to zero.

                   
                  Step 3 clear cdp table


                  Example:
                  Device# clear cdp table
                   

                  Clears the table that contains Cisco Discovery Protocol information about neighbors.

                   
                  Step 4 show cdp


                  Example:
                  Device# show cdp
                   

                  Displays the interval between advertisements, the number (in seconds) for which an advertisement is valid for a given port, and the version of the advertisement.

                   
                  Step 5 show cdp entry device-name [protocol | version]


                  Example:
                  Device# show cdp entry test-device protocol
                   

                  Displays information about a specific neighbor.

                   
                  Step 6 show cdp interface [type number]


                  Example:
                  Device# show cdp interface
                   

                  Displays information about interfaces on which Cisco Discovery Protocol is enabled.

                   
                  Step 7 show cdp neighbors [type number] [detail]


                  Example:
                  Device# show cdp neighbors
                   
                  Displays the type of device that has been discovered, the name of the device, the number and type of the local interface (port), the time (in seconds) the Cisco Discovery Protocol advertisement is valid for the interface, the device type, the device product number, and the port ID.

                  • The detail keyword displays information about the native VLAN ID, the duplex mode, and the VTP domain name associated with neighboring devices.

                   
                  Step 8 show cdp traffic


                  Example:
                  Device# show cdp traffic
                   

                  Displays information about Cisco Discovery Protocol traffic, including the number of packets sent and received and checksum errors.

                   
                  Step 9 show debugging


                  Example:
                  Device# show debugging
                   

                  Displays information about the types of debugging that are enabled for the device.

                   

                  Configuration Examples for Cisco Discovery Protocol Version 2

                  Example: Setting the Transmission Timer and Hold Time

                  In the following example, the timer is set to send updates every 30 seconds and a show cdp interface command is used to verify that the update is effective: 

                  Device(config)# cdp timer 30
Device(config)# end
Device# show cdp interface

Serial0 is up, line protocol is up
Encapsulation is HDLC
Sending CDP packets every 30 seconds
Holdtime is 180 seconds

                  In the following example, the hold time is set to 90 seconds and a show cdp interface command is used to verify that the update is effective: 

                  Device(config)# cdp holdtime 90
Device(config)# end
Device# show cdp interface

Serial0 is up, line protocol is up
Encapsulation is HDLC
Sending CDP packets every 30 seconds
Holdtime is 90 seconds

                  Example: Monitoring and Maintaining Cisco Discovery Protocol

                  The following example shows a series of commands that you can use to view Cisco Discovery Protocol information: 

                  Device# show cdp

Global CDP information:
        Sending CDP packets every 60 seconds
        Sending a holdtime value of 180 seconds
        Sending CDPv2 advertisements is enabled
 
Device# show cdp neighbors

Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
                  S - Switch, H - Host, I - IGMP, r - Repeater
 
Device ID        Local Interfce     Holdtme    Capability  Platform  Port ID
C2950-1          Fas 0/0            148         S I       WS-C2950T-Fas 0/15
RX-SWV.cisco.com Fas 0/1            167         T S       WS-C3524-XFas 0/13
Device# show cdp neighbors detail

-------------------------
Device ID: C2950-1
Entry address(es): 
Platform: Cisco WS-C2950T-24,  Capabilities: Switch IGMP 
Interface: FastEthernet0/0,  Port ID (outgoing port): FastEthernet0/15
Holdtime : 139 sec
Version :
Cisco IOS C2950 Software (C2950-I6Q4L2-M), Version 12.1(9)EA1, RELEASE SOFTWARE
 .
 .
 .
Device# show cdp traffic

CDP counters :
        Total packets output: 81684, Input: 81790
        Hdr syntax: 0, Chksum error: 0, Encaps failed: 0
        No memory: 0, Invalid packet: 0, Fragmented: 0
        CDP version 1 advertisements output: 0, Input: 0
        CDP version 2 advertisements output: 81684, Input: 81790

                  Additional References for Cisco Discovery Protocol Version 2

                  Related Documents

                  Related Topic

                  Document Title

                  Cisco IOS commands

                  Cisco IOS Master Command List, All Releases

                  Cisco Discovery Protocol commands

                  Cisco IOS Cisco Discovery Protocol Command Reference

                  SNMP support configuration tasks

                  “Configuring SNMP Support” module

                  On-Demand Routing configuration tasks

                  “Configuring On-Demand Routing” module

                  Debug commands

                  Cisco IOS Debug Command Reference

                  Standards

                  Standard

                  Title

                  IEEE 802.1Q

                  Virtual LANs

                  MIBs

                  MIB

                  MIBs Link

                  CISCO-CDP-MIB

                  To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

                  http:/​/​www.cisco.com/​go/​mibs

                  Technical Assistance

                  Description

                  Link

                  The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

                  To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

                  Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

                  http:/​/​www.cisco.com/​cisco/​web/​support/​index.html

                  Feature Information for Cisco Discovery Protocol Version 2

                  The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

                  Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to . An account on Cisco.com is not required.
                  Table 2 Feature Information for Cisco Discovery Protocol Version 2

                  Feature Name

                  Releases

                  Feature Information

                  Cisco Discovery Protocol Version 2

                  Cisco IOS XE Release 3.3SE

                  Cisco Discovery Protocol is a Layer 2, media-independent, and network-independent protocol that runs on Cisco devices and enables networking applications to learn about nearby, directly connected devices. This protocol facilitates the management of Cisco devices and allows systems using different network layer protocols to learn about one another.

                  In Cisco IOS XE Release 3.3SE, this feature is supported on Cisco 5700 Wireless LAN Controllers.

                  Configuration guide

                  Copyright © 2015, Cisco Systems, Inc. All rights reserved.

                  Was this Document Helpful?

                  FeedbackFeedback

                  Contact Cisco