-
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide
-
About this Guide
-
SIP and SPA Product Overview
-
Overview: Cisco ASR 1000 Series Aggregation Services Routers SIPs
-
Overview: Cisco ASR 1000 Series Aggregation Services Routers Shared Port Adapters
-
Preparing to Install a SIP or a Shared Port Adapter
-
Installing and Removing a SIP
-
Installing and Removing a Shared Port Adapter
-
Troubleshooting the Installation
-
Table Of Contents
Preparing for Online Removal of a SIP
Verifying Deactivation and Activation of a SIP
Preparing for Online Removal of a SPA
Verifying Deactivation and Activation of a SPA
Deactivation and Activation Configuration Examples
Deactivation of a SIP Configuration Example
Activation of a SIP Configuration Example
Deactivation of a SPA Configuration Example
Activation of a SPA Configuration Example
Installing and Removing a SIP
This chapter describes how to install or remove SIPs on the Cisco ASR 1000 Series Aggregation Services Routers. This chapter contains the following sections:
Handling SIPs
Each SIP circuit board is mounted to a metal carrier and is sensitive to electrostatic discharge (ESD) damage. See the "Preventing Electrostatic Discharge Damage" section on page 4-8 for ESD precautions.
Before you begin installation, read Chapter 4, "Preparing to Install a SIP or a Shared Port Adapter," for a list of parts and tools required for installation.
CautionAlways handle the SIP by the carrier edges and handle; never touch the SIP components or connector pins. (See Figure 5-1.)
When a slot is not in use, a blank filler plate must be installed in the empty slot to allow the router or switch to conform to electromagnetic interference (EMI) emissions requirements and to allow proper airflow across the installed modules. If you plan to install a SIP in a slot that is not in use, you must first remove the blank filler plate.
Figure 5-1 Handling a SIP
Online Insertion and Removal
The Cisco ASR 1000 Series Routers support online insertion and removal (OIR) of the SPA interface processor (SIP), in addition to each of the shared port adapters (SPAs). Therefore, you can remove a SIP with its SPAs still intact, or you can remove a SPA independently from the SIP, leaving the SIP installed in the router.
This section includes the following topics on OIR support:
•
•
•
•
•
Preparing for Online Removal of a SIP
The Cisco ASR 1000 Series Routers support OIR of the SIP. To do this, you can power down a SIP (which automatically deactivates any installed SPAs) and remove the SIP with the SPAs still intact.
Although graceful deactivation of a SIP is preferred using the hw-module slot stop command, the Cisco ASR 1000 Series Routers support removal of the SIP without deactivating it first. If you plan to remove a SIP, you can deactivate the SIP first, using the hw-module slot stop command in global configuration mode. When you deactivate a SIP using this command, it automatically deactivates each of the SPAs that are installed in that SIP. Therefore, it is not necessary to deactivate each of the SPAs prior to deactivating the SIP.
Either a blank filler plate or a functional SPA should reside in every subslot of a SIP during normal operation.
Deactivating a SIP
To deactivate a SIP and its installed SPAs prior to removal of the SIP, use the following command in global configuration mode:
For more information about chassis slot numbering, see the "Identifying Slots and Subslots for SIPs and SPAs" section on page 2-2.
Reactivating a SIP
If you did deactivate the SIP using the hw-module slot stop command, then you do not need to reactivate the SPAs after an OIR of the SIP. The installed SPAs automatically reactivate upon reactivation of the SIP in the Cisco ASR 1000 Series Router.
For example, consider the case where you remove a SIP from the Cisco ASR 1000 Series Router to replace it with another SIP. You reinstall the same SPAs into the new SIP. When you enter the hw-module slot start command on the Cisco ASR 1000 Series Router, the SPAs automatically reactivate with the new SIP.
To activate a SIP and its installed SPAs after the SIP has been deactivated, use the following command in global configuration mode:
For more information about chassis slot numbering, see the "Identifying Slots and Subslots for SIPs and SPAs" section on page 2-2.
Verifying Deactivation and Activation of a SIP
To verify the deactivation of a SIP, enter the show platform command in privileged EXEC configuration mode. Observe the State field associated with the SIP that you want to verify.
The following example shows that the Cisco ASR1000-SIP10 located in slot 1 is deactivated.
Router# show platformChassis type: ASR1006Slot Type State Insert time (ago)--------- ------------------- --------------------- -----------------0 ASR1000-SIP10 ok 2d20h0/0 SPA-1XOC12-POS ok 2d20h0/1 SPA-1XOC12-POS ok 1d21h0/2 SPA-5X1GE-V2 ok 2d20h0/3 SPA-4XOC3-POS-V2 ok 2d20h1 ASR1000-SIP10 disabled 1d23hR0 ASR1000-RP1 ok, active 1w3dF0 ASR1000-ESP10 ok, active 1w3dP0 Unknown ps, fail neverP1 Unknown ps, fail neverSlot CPLD Version Firmware Version--------- ------------------- ---------------------------------------0 06120701 12.2(20071009:051408) [gschnorr-mcp_...1 07091401 12.2(20070807:170946) [gschnorr-mcp_...R0 07010515 12.2(33r)XN2F0 07021400 12.2(20071030:180953) [gschnorr-mcp_...To verify activation and proper operation of a SIP, enter the show platform command and observe "ok" in the State field as shown in the following example:
Router# show platformChassis type: ASR1006Slot Type State Insert time (ago)--------- ------------------- --------------------- -----------------0 ASR1000-SIP10 ok 03:19:460/0 SPA-5X1GE-V2 ok 03:18:280/1 SPA-8X1FE-TX-V2 ok 03:18:280/2 SPA-2XCT3/DS0 ok 03:18:191 ASR1000-SIP10 ok 03:19:461/0 SPA-2XOC3-POS ok 03:18:281/1 SPA-8XCHT1/E1 ok 03:18:281/2 SPA-2XT3/E3 ok 03:18:18R0 ASR1000-RP1 ok, active 03:19:46F0 ASR1000-ESP10 ok, active 03:19:46P0 ASR1006-PWR-AC ok 03:19:14P1 ASR1006-FAN ok 03:19:14Preparing for Online Removal of a SPA
The Cisco ASR 1000 Series Routers support OIR of a SPA independently of removing the SIP. This means that a SIP can remain installed in the Cisco ASR 1000 Series Router with one SPA remaining active, while you remove another SPA from one of the SIP subslots. If you are not planning to immediately replace a SPA into the SIP, then be sure to install a blank filler plate in the subslot. The SIP should always be fully installed with either functional SPAs or blank filler plates.
If you are planning to remove a SIP along with its SPAs, then you do not need to follow the instructions in this section. To remove a SIP, see the "Preparing for Online Removal of a SIP" section.
Deactivating a SPA
Although graceful deactivation of a SPA is preferred using the hw-module subslot stop command in EXEC mode, the Cisco ASR 1000 Series Routers support removal of the SPA without deactivating it first. Before deactivating a SPA, ensure that the SIP is seated securely into the slot before pulling out the SPA itself.
Note
Choosing the Mode of the hw-module subslot Command
You can deactivate a SPA and all of its interfaces by using the hw-module subslot command in one of two modes:
•
•
To deactivate a SPA and all of its interfaces prior to removal of the SPA, use the following commands in global configuration mode:
For more information about chassis slot and SIP subslot numbering, refer to the "Identifying Slots and Subslots for SIPs and SPAs" section on page 2-2.
Reactivating a SPA
Note
If you deactivate a SPA using the hw-module subslot stop command and need to reactivate it without performing an OIR, you must use the hw-module subslot start command to reactivate the SPA and its interfaces.
To activate a SPA and its interfaces after the SPA has been deactivated, use the following command in global configuration mode:
Verifying Deactivation and Activation of a SPA
When you deactivate a SPA, the corresponding interfaces are also deactivated. This means that these interfaces will no longer appear in the output of the show interface command.
To verify the deactivation of a SPA, enter the show hw-module subslot all oir command in privileged EXEC configuration mode. Observe the Operational Status field associated with the SPA that you want to verify.
In the following example, the SPA located in subslot 1 of the SIP in slot 2 of the Cisco ASR 1000 Series Router is administratively down from the hw-module subslot shutdown command:
Router# show hw-module subslot all oirModule Model Operational Status-------------- ------------------ -------------------------subslot 2/0 SPA-1X10GE-L-V2 oksubslot 2/1 SPA-8X1GE-v2 admin downTo verify activation and proper operation of a SPA, enter the show hw-module subslot all oir command and observe "ok" in the Operational Status field as shown in the following example:
Router# show hw-module subslot all oirModule Model Operational Status-------------- ------------------ -------------------------subslot 2/0 SPA-1X10GE-L-V2 oksubslot 2/1 SPA-8X1GE-v2 okDeactivation and Activation Configuration Examples
This section provides the following examples of deactivating and activating SIPs and SPAs:
•
•
•
•
Deactivation of a SIP Configuration Example
Deactivate a SIP when you want to perform OIR of the SIP. The following example deactivates the SIP that is installed in slot 1 of the Cisco ASR 1000 Series Router, its SPAs, and all of the interfaces:
Router(config)# hw-module slot 1 stopActivation of a SIP Configuration Example
Activate a SIP if you have previously deactivated it. If you did not deactivate the SPAs, the SPAs automatically reactivate with reactivation of the SIP.
The following example activates the SIP that is installed in slot 1 of the Cisco ASR 1000 Series Router, its SPAs, and all of the interfaces (as long as the hw-module subslot shutdown command was not issued to also deactivate the SPA):
Router(config)# hw-module slot 1 startThere are no corresponding console messages shown with activation using this command. If you re-enter the hw-module slot start command, a message displays indicating that the module is already enabled.
Deactivation of a SPA Configuration Example
Deactivate a SPA when you want to perform OIR of that SPA. The following example deactivates the SPA (and its interfaces) that is installed in subslot 0 of the SIP located in slot 1 of the Cisco ASR 1000 Series Router and removes power to the SPA.
Router(config)# hw-module subslot 1/0 shutdown unpoweredActivation of a SPA Configuration Example
Activate a SPA if you have previously deactivated it. If you have not deactivated a SPA and its interfaces during OIR of a SIP, then the SPA is automatically reactivated upon reactivation of the SIP.
The following example activates the SPA that is installed in subslot 0 of the SIP located in slot 1 of the Cisco ASR 1000 Series Router.
Router(config)# no hw-module subslot 1/0 shutdown
SIP Installation and Removal
This section provides step-by-step instructions for installing and removing a SIP.
Caution
Caution
To install a SIP, refer to Figure 5-2 and do the following:
Step 1
Step 2
Step 3
Step 4
Step 5
To remove a SIP, refer to Figure 5-2 and do the following:
Step 1
Step 2
Step 3
Figure 5-2 illustrates how to install and remove a SIP in Cisco ASR 1000 Series Routers.
Figure 5-2 SIP Installation and Removal
