Table Of Contents
SIP and SPA Product Overview
Introduction to SIPs and SPAs
SPA Interface Processors
Shared Port Adapters
SIP and SPA Compatibility
Modular Optics Compatibility
SIP and SPA Product Overview
This chapter provides an introduction to SPA interface processors (SIPs) and shared port adapters (SPAs). It includes the following sections:
•
Introduction to SIPs and SPAs
•SIP and SPA Compatibility
•Modular Optics Compatibility
For software details for the specific SIPs and SPAs that are supported on the Cisco ASR 1000 Series Aggregation Services Routers, refer to the companion publication, Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide.
Introduction to SIPs and SPAs
Cisco ASR 1000 Series Aggregation Services Routers SIPs and SPAs are a carrier card and port adapter architecture that increases modularity, flexibility, and density across Cisco routers for network connectivity. This section describes the SIPs and SPAs and provides some guidelines for their use.
SPA Interface Processors
The following list describes some of the general characteristics of a SIP:
•A SIP is a carrier card that inserts into a router slot like a line card. It provides no network connectivity on its own.
•A SIP contains one or more subslots, which are used to house one or more SPAs. The SPA provides interface ports for network connectivity.
•During normal operation, the SIP should reside in the router fully populated either with functional SPAs in all subslots, or with a blank filler plate (SPA-BLANK=) inserted in all empty subslots.
•SIPs support online insertion and removal (OIR) with SPAs inserted in their subslots. SPAs also support OIR and can be inserted or removed independently from the SIP.
Note Fully populate all slots and subslots with blank filler plates or functional SPAs for maximum efficiency of the cooling system.
Shared Port Adapters
The following list describes some of the general characteristics of a SPA:
•A SPA is a modular type of port adapter that inserts into a subslot of a compatible SIP carrier card to provide network connectivity and increased interface port density. A SIP can hold one or more SPAs, depending on the SIP type.
•A single-height SPA inserts into one SIP subslot. (See Figure 1-1.)
Figure 1-1 Slot Orientation for SPAs
Caution SIP subslot 0 is not available on the Cisco ASR 1002 Router as that is the slot occupied by the integrated Route Processor with native Gigabit Ethernet ports.
•Each SPA provides a certain number of connectors, or ports, that are the interfaces to one or more networks. These interfaces can be individually configured using the Cisco IOS command-line interface (CLI).
•Either a blank filler plate or a functional SPA should reside in every subslot of a SIP during normal operation to maintain cooling integrity. Blank filler plates are available in single-height form only.
•SPAs support online insertion and removal (OIR). They can be inserted or removed independently from the SIP. SIPs also support OIR with SPAs inserted in their subslots.
SIP and SPA Compatibility
Table 1-1, Table 1-2, Table 1-3, Table 1-4, and Table 1-5 show SIP and SPA compatibility by SPA technology area on the Cisco ASR 1000 series router.
Note For more information about the introduction of support for different SIPs and SPAs, refer to the "Release History" sections in the overview chapters of the Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide.
Table 1-1 SIP and SPA Compatibility Table for ATM SPAs
SPA
|
Product ID
|
SIP Supported:
Cisco ASR1000-SIP10
|
1-Port Clear Channel OC-3 ATM SPA
|
SPA-1XOC3-ATM-V2
|
Yes
|
3-Port Clear Channel OC-3 ATM SPA
|
SPA-3XOC3-ATM-V2
|
Yes
|
1-Port Clear Channel OC-12 ATM SPA
|
SPA-1XOC12-ATM-V2
|
Yes
|
Table 1-2 SIP and SPA Compatibility Table for Ethernet SPAs
SPA
|
Product ID
|
SIP Supported:
Cisco ASR1000-SIP10
|
4-Port and 8-Port Fast Ethernet SPA
|
SPA-4X1FE-TX-V2 SPA-8X1FE-TX-V2
|
Yes
|
1-Port 10-Gigabit Ethernet SPA
|
SPA-1X10GE-L-V2
|
Yes
|
2-Port Gigabit Ethernet SPA
|
SPA-2X1GE-V2
|
Yes
|
5-Port Gigabit Ethernet SPA
|
SPA-5X1GE-V2
|
Yes
|
8-Port Gigabit Ethernet SPA
|
SPA-8X1GE-V2
|
Yes
|
10-Port Gigabit Ethernet SPA
|
SPA-10X1GE-V2
|
Yes
|
Table 1-3 SIP and SPA Compatibility Table for Packet Over SONET SPAs
SPA
|
Product ID
|
SIP Supported:
Cisco ASR1000-SIP10
|
1-Port OC-12c/STM-4 POS SPA
|
SPA-1XOC12-POS
|
Yes
|
2-Port, 4-Port, and 8-Port OC-12 POS SPA
|
SPA-2XOC12-POS
SPA-4XOC12-POS
SPA-8XOC12-POS
|
Yes
|
2-Port and 4-Port OC-3c/STM-1 POS SPA
|
SPA-2XOC3-POS SPA-4XOC3-POS
SPA-8XOC3-POS
|
Yes
|
1-Port OC-48 POS SPA
|
SPA-1XOC48-POS
|
Yes
|
2-Port and 4-Port OC-48c/STM-16 POS SPA
|
SPA-2XOC48-POS/RPR SPA-4XOC48-POS/RPR
|
Yes
|
1-Port OC-192 POS-XFP SPA
|
SPA-1XOC192-POS
|
Yes
|
Table 1-4 SIP and SPA Compatibility Table for Serial SPAs
SPA
|
Product ID
|
SIP Supported:
Cisco ASR1000-SIP10
|
2-Port and 4-Port Clear Channel T3/E3 SPA
|
SPA-2XT3/E3 SPA-4XT3/E3
|
Yes
|
2-Port and 4-Port Channelized T3 SPA
|
SPA-2XCT3/DS0 SPA-4XCT3/DS0
|
Yes
|
4-Port Serial Interface SPA
|
SPA-4XT-Serial
|
Yes
|
8-Port Channelized T1/E1 SPA
|
SPA-8XCHT1/E1
|
Yes
|
1-Port Channelized STM-1/OC-3 SPA
|
SPA-1XCHSTM1/OC3
|
Yes
|
Table 1-5 SIP and SPA Compatibility Table for Service SPAs
SPA
|
Product ID
|
SIP Supported:
Cisco ASR1000-SIP10
|
Cisco WebEx Node for ASR 1000 Series
|
SPA-WMA-K9
|
Yes
|
Modular Optics Compatibility
Some SPAs implement small form-factor pluggable (SFP) optical transceivers to provide network connectivity. An SFP module is a transceiver device that mounts into the front panel to provide network connectivity.
Cisco qualifies the SFP modules that can be used with SPAs.
Note The SPAs will only accept the SFP modules listed as supported in this document. An SFP module check is run every time an SFP module is inserted into a SPA and only SFP modules that pass this check will be usable.
Table 1-6, Table 1-7, Table 1-8, Table 1-9, and Table 1-10 show the types of optics modules that have been qualified for use with a SPA.
For more information about any of the supported transceivers for SPAs in these tables, refer to the Cisco Transceiver Modules site for that module on Cisco.com at:
http://www.cisco.com/en/US/products/hw/modules/ps5455/prod_installation_guides_list.html
Table 1-6 ATM SPA Optics Compatibility
SPA
|
Qualified Optics Modules (Cisco Part Numbers)
|
1-Port Clear Channel OC-3 ATM SPA
|
•SFP-OC3-MM
•SFP-OC3-IR-1
•SFP-OC3-LR-1
|
3-Port Clear Channel OC-3 ATM SPA
|
•SFP-OC3-MM
•SFP-OC3-IR-1
•SFP-OC3-LR-1
|
1-Port Clear Channel OC-12 ATM SPA
|
•SFP-OC12-MM
•SFP-OC12-SR
•SFP-OC12-IR1
•SFP-OC12-LR1
•SFP-OC12-LR2
|
Table 1-7 Gigabit Ethernet SPA Optics Compatibility
SPA
|
Qualified Optics Modules (Cisco Part Numbers)
|
1-Port 10-Gigabit Ethernet SPA
|
•XFP-10GLR-OC192SR
•XFP-10GER-OC192IR
•XFP-10GZR-OC192LR
•XFP-10G-MM-SR
|
2-Port Gigabit Ethernet SPA
|
•GLC-BX-D
•GLC-BX-U
•SFP-GE-S
•SFP-GE-L
•SFP-GE-Z
•SFP-GE-T
|
5-Port Gigabit Ethernet SPA
|
•GLC-BX-D
•GLC-BX-U
•GLC-FE-100FX
•SFP-GE-S
•SFP-GE-L
•SFP-GE-Z
•SFP-GE-T
|
8-Port Gigabit Ethernet SPA
|
•SFP-GE-S
•SFP-GE-L
•SFP-GE-Z
•SFP-GE-T
|
10-Port Gigabit Ethernet SPA
|
•GLC-BX-D
•GLC-BX-U
•SFP-GE-S
•SFP-GE-L
•SFP-GE-Z
•GLC-FE-100FX
|
Table 1-8 Gigabit Ethernet SPA CWDM Optics Compatibility for All Gigabit Ethernet SPAs Supported on the Cisco ASR 1000 Series Routers
Qualified Optics Modules (Cisco Part Numbers)
|
CWDM-SFP-1470=
CWDM-SFP-1490=
CWDM-SFP-1510=
CWDM-SFP-1530=
CWDM-SFP-1550=
CWDM-SFP-1570=
CWDM-SFP-1590=
CWDM-SFP-1610=
|
Table 1-9 Gigabit Ethernet SPA DWDM Optics Compatibility
SPA
|
Qualified Optics Modules (Cisco Part Numbers)
|
2-Port Gigabit Ethernet SPA
5-Port Gigabit Ethernet SPA
8-Port Gigabit Ethernet SPA
10-Port Gigabit Ethernet Spa
|
DWDM-SFP-3033=
DWDM-SFP-3112=
DWDM-SFP-3190=
DWDM-SFP-3268=
DWDM-SFP-3425=
DWDM-SFP-3504=
DWDM-SFP-3582=
DWDM-SFP-3661=
DWDM-SFP-3819=
DWDM-SFP-3898=
DWDM-SFP-3977=
DWDM-SFP-4056=
DWDM-SFP-4214=
DWDM-SFP-4294=
DWDM-SFP-4373=
DWDM-SFP-4453=
DWDM-SFP-4612=
DWDM-SFP-4692=
DWDM-SFP-4772=
DWDM-SFP-4851=
DWDM-SFP-5012=
DWDM-SFP-5092=
DWDM-SFP-5172=
DWDM-SFP-5252=
DWDM-SFP-5413=
DWDM-SFP-5494=
DWDM-SFP-5575=
DWDM-SFP-5655=
DWDM-SFP-5817=
DWDM-SFP-5898=
DWDM-SFP-5979=
DWDM-SFP-6061=
|
Table 1-10 POS SPA SFP and CWDM Optics Compatibility
SPA
|
Qualified Optics Modules (Cisco Part Numbers)
|
2-Port and 4-Port OC-3c/STM-1 POS SPA
|
•SFP-OC3-MM
•SFP-OC3-SR
•SFP-OC3-IR1
•SFP-OC3-LR1
•SFP-OC3-LR2
|
1-Port OC-48c/STM-16 POS SPA
|
•SFP-OC48-SR
•SFP-OC48-IR1
•SFP-OC48-LR2
|
2-Port and 4-Port OC-48c/STM-16 POS SPA
|
•SFP-OC48-SR
•SFP-OC48-IR1
•SFP-OC48-LR2
|
2-Port, 4-Port, and 8-Port OC-12 POS SPA
|
•SFP-OC3-MM
•SFP-OC3-SR
•SFP-OC3-IR1
•SFP-OC3-LR1
•SFP-OC3-LR2
|
1-Port OC-12c/STM-4 POS SPA
|
•SFP-OC12-MM
•SFP-OC12-SR
•SFP-OC12-IR1
•SFP-OC12-LR1
•SFP-OC12-LR2
|
1-Port OC-192 POS SPA
|
•XFP-10GLR-OC192SR
•XFP-10GER-OC192IR
•XFP-10GZR-OC192LR
|
