Table Of Contents
Preface
Purpose
Audience
Document Organization
Related Documentation
Conventions
Safety Information Referral Warning
Warning Definition
Terms and Acronyms
Obtaining Documentation and Submitting a Service Request
Preface
This section describes the purpose, audience, organization, and conventions used in this guide. This section also provides a revision history and a list of related documents as well as instructions for obtaining technical assistance and additional information.
Revision History
Date
|
Revision
|
Reason
|
16/11/2009
|
OL-18259-02
|
Added Cisco UBR-MC20X20V cable interface line card information.
|
12/15/2008
|
OL-18259-01
|
Updated with PRE4 information. Moved the document to online only.
|
04/05/2006
|
78-11450-03 Rev.B0
|
Updated Table 3-6.
|
06/28/2005
|
OL-5000-03
|
Added HHGE line card information.
|
10/18/2004
|
OL-5000-02
|
Updated with PRE2 information.
|
12/20/2003
|
OL-5000-01
|
Moved document to online only, updated format, added AC PEM specifications, and corrected PEM information, corrected PRE information, revised line card installation procedure.
|
03/20/2001
|
78-11450-03
|
Original publication and updates.
|
Purpose
This installation guide explains the initial hardware installation and basic configuration procedures for the Cisco uBR10012 universal broadband router. It contains procedures for installing the router hardware, creating a basic software configuration file, and starting up the router. After you complete the installation and basic configuration procedures covered in this guide, use the appropriate companion publications to more completely configure your system. See the documents listed in the "Related Documentation" section.
Audience
To use this publication, you should be familiar not only with Cisco router hardware and cabling, but also with electronic circuitry and wiring practices. You should be able to perform basic network configuration procedures, and preferably have experience as an electronic or electromechanical technician.
Warning 
Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030.
Document Organization
This publication is organized as follows:
Related Documentation
The following is a list of documents and URLs for the Cisco uBR10012 router:
•Cisco uBR10012 Universal Broadband Router Software Configuration Guide
http://www.cisco.com/en/US/docs/cable/cmts/ubr10012/configuration/guide/scg.html
•Regulatory Compliance and Safety Information for the Cisco uBR10012 Universal Broadband Router
http://www.cisco.com/en/US/docs/cable/cmts/ubr10012/regulatory/compliance/ub10rcsi.html
•Cisco UBR-MC20X20V Cable Interface Line Card Hardware Installation Guide
http://www.cisco.com/en/US/docs/interfaces_modules/cable/broadband_processing_engines/ubr10_mc20x20v/installation/guide/mc20x20v_hig.html
Additional documentation can be found here:
•For information on installing and replacing field-replaceable units (FRUs), such as the flash memory on Cisco uBR10012 routers, see the document for each FRU or go to the following URL:
http://www.cisco.com/en/US/products/hw/cable/ps2209/prod_installation_guides_list.html
•For information on using the Flash Disk, see the Using the Flash Disk document at the following URL:
http://www.cisco.com/en/US/docs/routers/7200/install_and_upgrade/flash_disk_install_config/6452fd.html
•For detailed Cisco IOS software configuration information and support, refer to the modular configuration and modular command reference publications in the Cisco IOS software configuration documentation set that corresponds to the software release installed on your Cisco hardware at the following URL:
http://www.cisco.com/en/US/products/ps6350/tsd_products_support_series_home.html
Specifically, you should refer to the following publications:
–For information on setting up quality of service (QoS), refer to the Quality of Service Solutions Configuration Guide and Quality of Service Solutions Command Reference publications.
–For information on encryption, refer to the Security Configuration Guide and the Security Command Reference publications.
–For information on interfaces, refer to the Cisco IOS Interface Configuration Guide and the Cisco IOS Interface Command Reference publications.
–For information on IP, refer to the Network Protocols Configuration Guide, Part 1 and the Network Protocols Command Reference, Part 1 publications.
You can also refer to the Cisco IOS software release notes for the version of software you are using on your Cisco uBR10012 router. Release notes for the Cisco uBR10012 router are found at the following URL:
http://www.cisco.com/en/US/products/sw/iosswrel/ps5012/prod_release_notes_list.html
•For information about cleaning fiber-optic connections, go to the following URL:
http://www.cisco.com/en/US/tech/tk482/tk876/technologies_white_paper09186a0080254eba.shtml
Conventions
Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in this publication.
Tip Means the following information might help you solve a problem.
Caution Means
reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.
Safety Information Referral Warning
See the following URL for the foreign language translations of all the warnings used in this guide:
http://www.cisco.com/en/US/docs/cable/cmts/ubr10012/regulatory/compliance/ub10rcsi.html
Warning Definition
|
Warning
|
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071
SAVE THESE INSTRUCTIONS
|
Waarschuwing
|
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.
BEWAAR DEZE INSTRUCTIES
|
Varoitus
|
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
|
Attention
|
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
|
Warnung
|
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
|
Avvertenza
|
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
|
Advarsel
|
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
|
Aviso
|
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
|
¡Advertencia!
|
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
|
Varning!
|
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.
SPARA DESSA ANVISNINGAR
|
|
|
|
|
|
|
|
|
|
|
Aviso
|
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
|
Advarsel
|
VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Terms and Acronyms
To fully understand the content of this guide, you should be familiar with the following terms and acronyms:
Note A complete list of terms and acronyms is available in the Internetworking Terms and Acronyms guide, available on Cisco.com and the Documentation CD-ROM. Also see the Glossary section at the end of this guide.
•ABR—Available bit rate
•AAL5—ATM adaptation layer 5
•AWG—American wire gauge
•CoS—Class of service
•CPE—Customer premises equipment
•CRC—Cyclic redundancy check
•CSU—Channel service unit
•CTS—Clear To Send
•DCD—Data Carrier Detect
•DCE—Data communications equipment
•DIMM—Dual in-line memory module
•DSR—Data set ready
•DSU—Data service unit
•DTE—Data terminal equipment
•DTR—Data terminal ready
•EMC—Electromagnetic compliance
•EMI—Electromagnetic interference
•ESD—Electrostatic discharge
•FRU—Field-replaceable unit (router components that do not require replacement by a Cisco-certified service provider)
•FTP—Foil twisted-pair
•HDLC—High-Level Data Link Control
•HHGE—Half-Height Gigabit Ethernet
•IPSec—IP Security Protocol
•MAC—Media Access Control
•MB—Megabyte
•MM—Multimode
•nrt-VBR—Non-real time variable bit rate
•NVRAM—Nonvolatile random-access memory
•OAM AIS—Operation, Administration, and Maintenance alarm indication signal
•OIR—Online insertion and removal
•PCI—Peripheral Component Interconnect
•PCMCIA—Personal Computer Memory Card International Association
•PPP—Point-to-Point Protocol
•QoS—Quality of service
•rcp—remote copy protocol
•RFI—Radio frequency interference
•RIP—Routing Information Protocol
•RISC—Reduced Instruction Set Computing
•RTS—Request To Send
•SDRAM—Synchronous dynamic random-access memory
•SIMM—Single in-line memory module
•SMI—Single-mode intermediate reach
•SNMP—Simple Network Management Protocol
•TCP/IP—Transmission Control Protocol/Internet Protocol
•TDM—Time-division multiplexing
•TFTP—Trivial File Transfer Protocol
•UBR—Unspecified bit rate
•UDP—User Datagram Protocol
•UNI—User-Network Interface
•UTP—Unshielded twisted-pair
•VC—Virtual circuit
•VPN—Virtual Private Network
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.
